First complete the electrical connections, and then check them for correctness.
Installation
This unit can be installed
dashboard having an opening as
shown on the picture. The
dashboard should be
mm thick
support the unit.
1.
Insert mounting collar into the
dashboard, and bend the
mounting tabs out with a
screwdriver.
Make sure that lock lever C
flush with the mounting collar (not
projecting outward).
2.
Secure the rear
After fixing mounting bolt and power connector, fix the rear
cushion.
3.
Insert trim plate.
When you prepare to insert trim plate, please check its direction. Once it was up side down, it
cannot be fixed.
in
order to be able to
of
in
any
4.
75 - 5.56
*)
the unit.
is
Lock lever ( * )
of
the unit to the car body by rubber
U n-installation
Remove Trim Ring and insert Release Keys into left and
right side-end holes as shown
the unit out
of
the dashboard.
in
below picture and pull 0
~
..
5
Make sure you have good chassis ground. A good ground connection
will eliminate
most
electrical noise problems. A good chassis ground requires a tight connection to the vehicle's
metal chassis. The area around the ground connection should be clean, bare metal without rust,
paint, plastic, dust, or dirt for a good electrical connection.
Caution:
Do not interchange the connection of the wiring!!!
For some car models you may need to modify wiring
authorized car dealer before
installing
this unit.
SeUNDSTREAM
ISO
AJ
To
co
nn
(GNOJ[B
A4
To
te
rmin
wi
th
pow
A5
To
sys
of
the
contr
DC)(
Blue)
A7
To
el
ec
by
ign
ON/
OF
AS
To
v
ehicl
Speaker
ect
ro
al
er
tem
pow
ol
ter
tric
it
ion
F(
ACC B +](R ed )
e (
Pa
rking t o se e vi
wn)
alw
ays supplied
(M
em
or y
contr
ol
er
a
mp
mmal(
max.
termina
switch(
meta
l)b
Connection
deo
B+)(Yell
ow
)
ter
mi
nal
or
Au
to
-an
tenna
30DmA
12V
l con
tr
oll ed
1
2V
DC)
ody.(GNO)(Biack)
FJnWID~
Fr
83
84
85
86
Rear
81
82
87
88
ont
speaker
Ri
gh
Ri
ght
Left+
Left
speaker
Ri
ght+
Ri
ght
Left+
Left-
~
mm~
t +
-
-
-
of
the supplied power cord. Contact your
USB/SD,MP3/MP4,AM/FM
immrr==n
~r
+-+-
STEREO
--
Using the ISO
1.
If
your car is equipped with the
2.
For connections without the
Connector
ISO
connector, then connect the
ISO connectors, check the wiring
ISO
in
the vehicle
connecting, incorrect connection may cause serious damage to this unit.
3.
Cut the connector; connect the colored leads
of
the power cord to the car battery as shown
the color code table below for speaker and power cable connections.
Location Function
Connector A Connector B
1
2
3
4
5
6
7
8
Parking (GND)---Brown
Battery 12V
(+)---Yellow
Auto Antenna---Blue
ACC(
+)---Red
Ground---Black
Rear Right(+ )---Purple
Rear Right(-)---Purple/Black Stripe
Front Right(+ )---Grey
Front Right(-)---Grey/Black Stripe
Front Left(+ )---White
Front Left(- )---White/Black Stripe
Rear Left(+ )---Green
Rear Left(-)---Green/Black Stripe
connectors as illustrated.
carefully
before
in
6
f-l:!::::i!~
--t
1
--t---
2
3
----.~
4
6 7 8 9
10
14
1)
2)
3)
4)
5)
6)
7)
8)
9)
Power
EQ
SEL
Mode button
SCAN
MENU button
Volume/OK
AS/PS
BAND