Soundstream REF300.2, REF600.2, REF480.4, REF800.4, REF880.5 Owner's Manual
...
REFERENCE
AMPLIFIER SERIES
REF300.2 / REF600.2 / REF800.2 / REF1600.2
REF480.4 / REF800.4 / REF880.5
OWNER’S MANUAL
BEDIENUNGSANLEITUNG
[ 2 ]
TABLE OF CONTENTS
Features / Specifications
Power Ratings / Dimensions
Wiring
Panel Layout
Key to Callouts
2Ch System Design #1, 2
2Ch System Design #3
4Ch System Design #1
4Ch System Design #2
4Ch System Design #3
5Ch System Design #1, 2
5Ch System Design #3
5Ch System Design #4
Trouble Shooting
BEDIENUNGSANLEITUNG DEUTSCH
3
4
5
6 / 7
8
9
10
10
11
12
13
14
15
16
17
PAGE
[ 3 ]
FEATURES
• RUBI™ (Rapid-Use Branched Impulse) – proprietary power supply topology
• STACT™ (Stabilized Apex Current Topology) – reduces power supply stress by 50%
• Trident™ amplifier protection topology
• Ultra-Low ESR Capacitance Bank – ensures rapid power delivery for dynamic peaks
• Hawkins Bass Control™– proprietary bass equalization topology
• IDI™ (Intelligent Distress Indicator) – visual indication of amplifier protection status
• Harmonic Bass Alignment™ – produces tighter, more accurate bass
• Fully regulated MOSFET power supply
• Triple Darlington Output Circuitry
• BIP™ (Bias Input Protection)
• Rail Stabilization Protection Circuitry
• Bi-Linear selectable two-way crossovers for amplifier and line output
• Continuously Variable High and Low Pass Crossovers
• Vortex Induction Fan Thermor Management
• Gold RCA Inputs and Outputs
• Gold 4-gauge Power Connectors
• Tri-mode operation
SPECIFICATIONS
10 Hz - 70 kHz
< 0.02 %
115dB
0.15~12.0 Volts
10k Ohms
2 - 8 Ohms
4 - 8 Ohms
11 - 15 Volts
>500
>50 V/µS
Up to +18dB Boost @ 18Hz~80Hz
18dB/Octave
30Hz-4kHz
Power Bandwidth
Total Harmonic Distortion
S/N Ratio
Input Sensitivity
Input Impedance
Load Impedance (stereo)
Load Impedance (bridged)
Supply Voltage
Damping Factor
Slew Rate
Hawkins Bass
Crossovers
Crossover Frequency
[ 4 ]
POWER RATINGS & FUSES
MODEL
REF620.2
REF800.2
REF1600.2
REF480.4
REF800.4
REF880.5
4 ohm STEREO
175w x 2ch
240w x 2ch
480w x 2ch
70w x 4ch
125w x 4ch
70w x 4ch
200w x 1ch(sub)
2 ohm STEREO
310w x 2ch
400w x 2ch
800w x 1ch
140w x 4ch
200w x 4ch
120w x 4ch
400w x 1ch(sub)
4 ohm BRIDGED
620w x 1ch
800w x 1ch
1600w x 1ch
280w x 2ch
400w x 2ch
240w x 2ch
400w x 1ch
FUSE
80 Amp
133 Amp
240 Amp
90 Amp
150 Amp
125 Amp
MODEL
REF300.2
REF620.2
REF800.2
REF1600.2
REF480.4
REF800.4
REF880.5
Height
54 mm
54 mm
54 mm
54 mm
54 mm
54 mm
54 mm
Length
280 mm
345 mm
415 mm
505 mm
390 mm
415 mm
525 mm
Width
250 mm
250 mm
250 mm
250 mm
250 mm
250 mm
250 mm
DIMENSIONS
REF300.2
100w x 2ch
150w x 2ch 300w x 1ch
40 Amp
[ 5 ]
Positive
Battery
Terminal
Fuse must be
installed within
18" of battery
Drill a hole in the
firewall and use
a rubber grommet
to keep wire
from shortings
Run the cables under
the carpet near the
side of the vehicle.
Be careful not to drill
or screw into the
wires when you
replace the trim.
Ground wire to solid
metal of rear chassis
Avoid sharp edges that
could chafe through the
insulation
Run signal cables
(RCAs) and
remote turn-on
lead
down the
opposite side of
the vehicle of the
power
wire to avoid
radiated noise
Factory Ground wire may
need to be replaced if it is
small, frayed, or broken
Before beginning, disconnect the negative (-) terminal of the battery prior to
working on the positive (+) terminal to prevent a short to ground. This is important to avoid serious damage to your car audio system and your car electrics.
Reconnect the negative terminal only after all connections have been made.
WIRING
[ 6 ]
PANEL LAYOUT
REF300.2 / REF620.2 / REF800.2 / REF1600.2
PANEL LAYOUT
REF300.2 / REF620.2 / REF800.2 / REF1600.2
[ 7 ]
[ 8 ]
KEY TO CALLOUTS
GND - Main ground connection. Bolt to a clean chassis point in the vehicle.
+12V - Connected to a fuse or circuit breaker, then to the battery’s positive terminal.
REM - Remote Turn-ON is connected to Radio's power antenna lead or a switchable
+12V - FUSES- Satellite channels power supply fuses.
Warning: Replace only with the same value fuses
Speaker Connection Terminal - Connect Speakers here - ensure correct polarity.
Subsonic Filter - Frequency adjustment control for Subsonic Filter.
Selectable X-Over LP/HP/FULL
LP - Frequency adjustment control for Low Pass Filter
HP - Frequency adjustment control for High Pass Filter
Full - Full Range Signal Output
Hawkins Bass-EQ Control Adjustment
Frequency adjustment control for Hawkins Bass Control filter.
Hawkins Bass-Boost Control Adjustment
Varies from 0 to + 18 dB of boost when the Hawkins Bass Control circuit is engaged.
Input Attention: ATT. Switch ‘ON’ for high voltage input (4V to 12V) capability. This
switch ‘ON’ must be used for speaker level input on common ground headunits
or high voltage line drivers.
Input Gain - Input gain control variable from 150mV to 4V or 4V to 12V
RCA Inputs - Connect the RCA cables from source unit, or line driver to these
RCA connectors.
RCA Line Outputs - Left and right RCA Line outputs provides Full Range Signal.
Status LED - Indicates amplifier power. (Power: Green / Protection : Red)
[ 9 ]
2 CHANNEL SYSTEM DESIGN #1
REF300.2/620.2/800.2/REF1600.2
2 CHANNEL SYSTEM DESIGN #2
REF300.2/620.2/800.2/REF1600.2
[ 10 ]
2 CHANNEL SYSTEM DESIGN #3
REF300.2/620.2/800.2/REF1600.2
4 CHANNEL SYSTEM DESIGN #1
REF480.4/800.4
Loading...