Page 1
Please read this manual carefully and proper take care of this manual.
USER MANUAL
PAR-18-18W-IP65
18x18W RGBWA+UV 6in1 LED PAR Light for
Outdoor use (IP65)
Page 2
Dear customer,
First of all thanks for purchasing a SOUNDSATION® product. Our mission is to satisfy
all possible needs of musical instrument, professional audio and lighting users offering
a wide range of products using the latest technologies.
We hope you will be satised with this item and, if you want to collaborate, we are
looking for a feedback from you about the operation of the product and possible improvements to introduce in the next future. Go to our website www.soundsationmusic.
com and send an e-mail with your opinion, this will help us to build instruments ever
closer to customer’s real requirements.
One last thing: read this manual before using the instrument, an incorrect operation
can cause damages to you and to the unit. Take care!
The SOUNDSATION Team
Page 3
TABLE OF CONTENTS
1. 1. INTRODUCTION ....................................................................................................5
1.1. UNPACKING .............................................................................................................................................................6
1.2. ACCESSORIES ..........................................................................................................................................................6
2. OVERVIEW ..................................................................................................................6
3. MAIN FEATURES ........................................................................................................ 6
4. OVERHEAD RIGGING ................................................................................................7
5. MAINS CONNECTIONS .............................................................................................7
6. DMX CONNECTION ................................................................................................... 7
6.1. DMX Terminator ..................................................................................................................................................... 8
6.2. 3-Pin vs 5-Pin DMX cables .................................................................................................................................9
7. FRONT PANEL ............................................................................................................9
8. MENU INSTRUCTION .............................................................................................. 10
9. OPERATION MODES ................................................................................................10
10. DMX Channel Chart ................................................................................................11
11. SPECIFICATIONS ......................................................................................................13
12. WARRANTY AND SERVICE .....................................................................................14
13. WARNING.................................................................................................................14
3
ENGLISH
Page 4
IMPORTANT SAFETY SYMBOLS
The symbol is used to indicate that some hazardous live terminals are
involved within this apparatus, even under the normal operating con-
ditions, which may be sufcient to constitute the risk of electric shock
or death.
The symbol is used in the service documentation to indicate that spe-
cic component shall be replaced only by the component specied in
that documentation for safety reasons.
Protective grounding terminal
Alternating current/voltage
Hazardous live terminal
Denotes the apparatus is turned on
Denotes the apparatus is turned off
WARNING:
Describes precautions that should be observed to prevent the danger
of injury or death to the operator.
CAUTION:
Describes precautions that should be observed to prevent danger of
the apparatus.
To protect the environment, please try to recycle the packing material
as much as possible
Don’t throw this product away just as general trash, please deal with
the product follow the abandon electronic product regulation in your
country.
TAKING CARE OF YOUR PRODUCT
f Read these instructions
f Keep these instructions
f Follow all instructions
Water / Moisture
The apparatus should be protected from moisture and rain and can not be used near
water; for example near a bathtub, a kitchen sink, a swimming pool, etc.
Heat
The apparatus should be located away from heat sources such as radiators, stoves or
4
ENGLISH
PAR-18-18W-IP65 User manual
Page 5
other appliances that produce heat. Don not use it when maximum ambient temperature is higher than 40°C.
Object and Liquid Entry
Objects do not fall into and liquids are not spilled into the inside of the apparatus for
safety.
Power Cord and Plug
Protect power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus. Do not defeat the safety
purpose of the polarized or grounding-type plug. A polarized plug has two poles; a
grounding-type plug has two poles and a third grounding terminal. The third prong is
provided for your safety. If the provided plug does not t into your outlet, refer to an
electrician for replacement. Unplug the unit when it is not used for a longer time.
Electrical Connection
Always disconnect from the power source before servicing or replacing fuse and be
sure to replace with same fuse size and type. Cut off power before moving, repairing
and cleaning the unit. Improper electrical wiring may invalidate the product warranty.
To avoid electric shock, all xtures must be connected to circuits with a suitable ground.
Do not power on and power off the xture in a short time.
DMX connection
When use DMX controller, please make sure that there is no interference sources (e.g.
intercom, high frequency radio waves and radiation source).
Cleaning
Clean only with a dry cloth. Do not use any solvents such as benzene or alcohol.
Servicing
Do not implement any servicing other than those means described in the manual. Refer
all servicing to qualied service personnel only. Only use accessories/attachments or
parts recommended by the manufacturer.
1. 1. INTRODUCTION
Thank you for purchasing our PAR-18-18W-IP65 graphic laser. Enjoy your new equipment and make sure to read this manual carefully before operation!
This user manual is made to provide both an overview of controls, as well as information on how to use them. In order to help you to understand the connections between
the various controls, we have gathered in groups according to their functions.
5
ENGLISH
PAR-18-18W-IP65 pro User manual
Page 6
1.1. UNPACKING
Your PAR-18-18W-IP65 was carefully packed to ensure safe transport. Despite this, we
recommend you to carefully examine the package and its contents for any signs of
physical damage, which can occur during transport. It is composed by following parts:
f Waterproof PAR light
f Power Cable
f DMX Cable
f User manual
ATTENTION: Packaging bag is not a toy! Keep out of reach of children!!! Keep in
a safe place the original packaging material for future use.
1.2. ACCESSORIES
SOUNDSATION can supply a wide range of quality accessories that you can use with
your PAR-18-18W-IP65, like Cables, Splitters, DMX controllers, and a wide range of
xtures.
All products in our catalogue has been long tested with this device, so we recommend
you to use Genuine SOUNDSATION Accessories and Parts.
Ask your SOUNDSATION dealer or check out our website www.soundsationmusic.com
for any accessories you could need to ensure best performance of the product.
2. OVERVIEW
Especially designed for outdoor use thanks to the IP65 protection degree, SOUNDSATION PAR-18-18W-IP65 is the right choice for architectural applications when a powerful (18 x 18W) projector is required. It offers a complete color palette thanks to the 6in1
LED technology, which provides Red, Green, Blue, White, Amber and Ultra Violet basic
colors. The accurate and smooth color mixing, the 6CH/7CH/10CH DMX control mode,
the Master/Slave, Auto, and Sound Active modes make this xture extremely versatile.
3. MAIN FEATURES
f DMX512 protocol, Master/Slave mode, Sound Active mode, Auto Run mode
f Light source: 18x18W RGBWA+UV 6in1 LED
f Light Emission: 30000 Lux @1m (RGBWA+UV max)
f Beam Angle: 25°
f DMX channel modes: 6CH / 10CH-1 / 10CH-2
f LED display fox quick access to setup
f Suitable for Disco, club, bar, DJ gig, etc.
6
ENGLISH
PAR-18-18W-IP65 User manual
Page 7
4. OVERHEAD RIGGING
WARNING: The installation must be carried out by qualied service personal
only. Improper installation can result in serious injuries and /or damage to
property. Overhead rigging required extensive experience! Working load
limits should be respected, Certied installation materials should be used,
the installed device should be inspected regularly for safety.
• Make sure the area below the installation place is free from unwanted persons
during rigging, de -rigging and servicing.
• Locate the xture in a well ventilated spot, far away from any ammable materials
and/or liquids. The xture must be xed at least 50cm from surrounding walls.
• The device should be installed out of reach of people and outside areas where
persons may walk by or be seated.
• Before rigging, make sure that the installation area can hold minimum point load
of 10 times the device”s weight. The device should be well xed; a free swinging
mounting is dangerous and may not be considered!
• Before the rst time use, it must be inspected by professional staff to make sure
safety, inspection regularly every year.
5. MAINS CONNECTIONS
Connect the device to the mains with the supplied power cable. Please note that power
voltage and frequency are the same as the marked voltage and frequency of device
when connecting power. Wire correspondence is as follow:
Cable (EU) Pin International
Brown Live L
Blue Neutral N
Yellow/Green Earth
The earth must to be connected! Pay attention to the safety! Before taking
into operation for the rst time, the installation has to be approved by an
expert.
6. DMX CONNECTION
DMX xtures are designed to receive data through a serial Daisy Chain. A Daisy Chain
connection is where the DATA OUT of one xture connects to the DATA IN of the next
xture. The order in which the xtures are connected is not important and has no effect
on how a controller communicates to each xture. Use an order that provides for the
easiest and most direct cabling.
7
ENGLISH
PAR-18-18W-IP65 pro User manual
Page 8
DMX Termonator
Unit 1 Unit 2 Last Unit
DMX 512
Connect xtures using shielded 2-conductor twisted pair cable with 3-pin XLR male to
female connectors. The shield connection is pin 1, while pin 2 is Data Negative (S-), and
pin 3 is Data positive (S+).
3-Pin XLR
Pin 1: GND
Pin 2: DMX Pin 3: DMX +
OUTPUTINPUT
DMX use of 3-Pin XLR Connectors
CAUTION: Wires must not come into contact with each other; otherwise the
xtures will not work at all, or will not work properly.
6.1. DMX Terminator
DMX is a resilient communication protocol, however errors still occasionally occur.
In order to prevent electrical noise from disturbing and corrupting the DMX control
signals, a good habit is to connect DMX output of last xture in the chain to a DMX
terminator, especially over long signal cable runs.
120ohm, 1/4W
resistor
DMX Terminator
The DMX terminator is simply an XLR connector with a 120Ω (ohm), 1/4 Watt resistor
connected across Signal (-) and Signal (+), respectively, pins 2 and 3, which is then
plugged into the output socket on last projector in the chain. The connections are
illustrated below.
Complimentary signal cable can transmits signals to 20 unit xtures at most.
8
ENGLISH
PAR-18-18W-IP65 User manual
Page 9
Signal amplier is a must to connect more xtures.
6.2. 3-Pin vs 5-Pin DMX cables
DMX connection protocols used by controllers and xtures manufacturers are not standardized around the world. However, two are the most common standards: 5-Pin XLR
and 3-Pin XLR system. If you wish to connect SCENESPLIT 8 RACK to a 5-Pin XLR input
xture, you need to use an adapter-cable or make it by yourself.
Following the wiring correspondence between 3-Pin and 5-Pin plug and socket standards
5-Pins XLR (plug)
Pin 1: GND (Screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
3-Pins XLR (socket)
Pin 1: GND (Screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
5-Pins XLR (socket)
Pin 1: GND (Screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
3-Pins XLR (plug)
Pin 1: GND (Screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
7. FRONT PANEL
POWER out
POWER in
(100-240v/50-60Hz)
DMX OUT
DMX IN
PAR-18-18W-IP65
enterMENU
2
4
1
3
5
1. Power Input: Power input cable
2. Power Output: Power output cable
3. DMX input: 3-wire DMX input cable
4. DMX output: 3-wire DMX output cable
5. LED display: User interface to control xture operation and settings.
9
ENGLISH
PAR-18-18W-IP65 pro User manual
Page 10
enterMENU
6
9
7
8
6. MENU: Used to select different menu items.
7. UP: To go up in the menu and to increase values shown on the display.
8. DOWN: To go back in the menu and to lower values shown on the display.
9. ENTER: Used to conrm your choice.
8. MENU INSTRUCTION
With the help of the LED display, it’s very easy to set and change operating mode.
Display Instruction
A001 (A001 - A512) 10 channel mode
d001 (d001 - d512) 6 channel mode
H001 (H001 - H512) 10 channel mode
CL01 (CL01 - CL32) 32 build-in color
CC01 (CC01 - CC99) Color jump, speed from slow to fast
EE01 (EE01 - EE99) Slow off, quick on, speed from slow to fast
FF01 (FF01 - FF99) Color fade, speed from slow to fast
ST01 (ST01 - ST32)
SP01 - SP99
1-32 kinds of strobe effect
Speed from slow to fast
SOU1 (SE01-SE99)
SOU2 (SE01-SE99)
SOU3 (SE01-SE99)
SOU1: led changeable effect
SOU2: strobe effect
SOU3: Lightning strobe effect
R255 (R000—R255) Red Dimmer, 0-100%
G255 (R000—R255) Green Dimmer, 0-100%
B255 (R000—R255) Blue Dimmer, 0-100%
W255 (R000—R255) White Dimmer, 0-100%
Y255 (R000—R255) Amber Dimmer, 0-100%
P255 (R000—R255) Ultra Violet Dimmer, 0-100%
9. OPERATION MODES
The unit has several working modes:
f Auto mode - Built-in programs (Color Jump, Color Fade, Strobe)
10
ENGLISH
PAR-18-18W-IP65 User manual
Page 11
f Sound mode - 3 built-in Sound modes
f Master/Slave mode - When active, the unit controls other PARs connected via DMX
cables. To set Master mode please refer to “8. MENU INSTRUCTION” at page 10,
you can use CL01 (CL01-CL32) in case of 32-internal colors, or CC01 (CC01-CC99)
for jump function, or EE01 (EE01-EE99) in case of color change program, FF01 (FF01FF99) for color fade, ST01 (ST01-ST32) for strobe effect, SOU1-3 (SE01-SE99) to set
Strobe effect type, R255 - G255, B255, W255, Y255, and P255 for single x colors. The
controlled units must be set to Slave mode; slave is A001/d001/H001.
f DMX512 mode - DMX512 control via controller.
10. DMX Channel Chart
6CH Mode (d001)
Channel Value Description
CH1 000 - 255 Red Dimmer 0 - 100%
CH2 000 - 255 Green Dimmer 0 - 100%
CH3 000 - 255 Blue Dimmer 0 - 100%
CH4 000 - 255 White Dimmer 0 - 100%
CH5 000 - 255 Amber Dimmer 0 - 100%
CH6 000 - 255 Ultra Violet Dimmer 0 - 100%
10CH-1 (A001)
Channel Value Description
CH1 000 - 255 Linear dimmer, 0-100%
CH2 000 - 255 Red Dimmer, 0-100%
CH3 000 - 255 Green Dimmer, 0-100%
CH4 000 - 255 Blue Dimmer, 0-100%
CH5 000 - 255 White Dimmer, 0-100%
CH6 000 - 255 Amber Dimmer, 0-100%
CH7 000 - 255 Ultra Violet Dimmer, 0-100%
CH8
Strobo
000 - 009 Strobo (No Function)
010 - 255 Strobo, Slow to fast
CH9
Macro Function
000 - 009 No function
010 - 050 Static color
051 - 100 Slow off, quick on
101 - 150 Led jump
151 - 200 Led fade
201 - 220 SOU1: led changeable effect
221 - 240 SOU2: strobe effect
241 - 255 SOU3: Lightning strobe effect
11
ENGLISH
PAR-18-18W-IP65 pro User manual
Page 12
CH10
Color change /
Speed adjustment
(Works with CH9)
000 - 255
(When CH9: 010-050) push CH10 to a static color selection
(When CH9: 051-200) push CH10 for the additional speed. Speed
changes from slow to fast.
10CH-2 (H001)
Channel Value Description
CH1 000 - 255 Linear dimmer, 0-100%
CH2
Strobo
000 - 008 Strobo (No Function)
009 - 255 Strobo, Slow to fast
CH3
Macro Function
000 - 009 No function
010 - 050 Static color
051 - 100 LED jump
101 - 150 Slow off, quick on
151 - 200 Led fade
201 - 255 Sound active
CH4
Color change /
Speed adjustment
(Works with CH3)
000 - 255
(When CH3: 010-050) pushes CH4 to a static color selection
(When CH9: 051-200) pushes CH4 for the additional speed. Speed
changes from slow to fast.
CH5 000 - 255 Red Dimmer, 0-100%
CH6 000 - 255 Green Dimmer, 0-100%
CH7 000 - 255 Blue Dimmer, 0-100%
CH8 000 - 255 White Dimmer, 0-100%
CH9 000 - 255 Amber Dimmer, 0-100%
CH10 000 - 255 Ultra Violet Dimmer, 0-100%
12
ENGLISH
PAR-18-18W-IP65 User manual
Page 13
11. SPECIFICATIONS
Model PAR-18-18W-IP65
Light source 18 x 18W RGBWA+UV 6IN1 LED
Beam angle 25°
Lux @ 1m
R 3000 Lux, G 6000 Lux, B 6000 Lux, W12000 Lux, A 3000
Lux, UV 2500 Lux, RGBWA+UV 30000 Lux
DMX Channel Modes 6CH, 10CH-1, 10CH-2
Maximum External Temp 104°F (40°C)
Cooling System Convection (No Fan)
Power Supply Type Switching (internal)
Range 100-240V 50/60Hz
Consumption 230W
Light Size (LxHxD)
260x310x250 mm (bracket installed)
Light Weight
4 kg
Packing Size (LxHxD)
290x290x340 mm
Packing Weight
4.5 kg
13
ENGLISH
PAR-18-18W-IP65 pro User manual
Page 14
12. WARRANTY AND SERVICE
All SOUNDSATION products feature a limited two-year warranty. This two-year warranty is specic
to the date of purchase as shown on your purchase receipt.
The following cases/components are not covered from the above warranty:
• Any accessories supplied with the product
• Improper use
• Fault due to wear and tear
• Any modication of the product effected by the user or a third party
SOUNDSATION shall satisfy the warranty obligations by remedying any material or manufacturing
faults free of charge at SOUNDSATION’s discretion either by repair or by exchanging individual
parts or the entire appliance. Any defective parts removed from a product during the course of a
warranty claim shall become the property of SOUNDSATION.
While under warranty period, defective products may be returned to your local SOUNDSATION
dealer together with original proof of purchase. To avoid any damages in transit, please use the
original packaging if available. Alternatively you can send the product to SOUNDSATION SERVICE
CENTER – Via Enzo Ferrari , 10 – 62017 Porto Recanati - Italy . In order to send a product to service
center you need an RMA number. Shipping charges have to be covered by the owner of the product.
For further information please visit www.soundsationmusic.com
13. WARNING
PLEASE READ CAREFULLY – EU and EEA (Norway, Iceland and Liechtenstein) only
This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE Directive (2202/96/EC) and your national law.
This product should be handed over to a designated collection point, e.g., on an authorized onefor-one basis when you buy a new similar product or to an authorized collection site for recycling
waste electrical and electronic equipment (WEEE).
Improper handling of this type of waste could have a possible negative impact on the environment
and human health due to potentially hazardous substances that are generally associated with EEE.
At the same time, your cooperation in the correct disposal of this product will contribute to the
effective usage of natural resources.
For more information about where you can drop off your waste equipment for recycling, please
contact your local city ofce, waste authority, approved WEEE scheme or your household waste
disposal service.
14
ENGLISH
Page 15
This product is imported in EU by
Questo prodotto viene importato nella UE da
FRENEXPORT SPA – Via Enzo Ferrari, 10 - 62017 Porto Recanati - Italy
www.soundsationmusic.com
Soundsation® is a registered trademark of FRENEXPORT SPA - Italy
Soundsation® è un marchio di fabbrica registrato della FRENEXPORT SPA - Italy
Page 16
www.soundsationmusic.com
Ver 1.0 - July 2017
Loading...