Soundmax SM-CMD3019 User manual

SM-CMD3019

Мультимедийный DVD/CD/MP3-ресивер со встроенным 3” TFT-дисплеем Руководство по эксплуатации

Multimedia DVD/CD/MP3 receiver with built-in 3” TFT display Instruction manual

Dear customer!

Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future.

Table of contents

TABLE OF CONTENTS ...................................................................................................................................................... 2

IMPORTANT SAFEGUARDS ............................................................................................................................................ 3

ACCESSORIES .................................................................................................................................................................... 4

INSTALLATION/CONNECTIONS ................................................................................................................................... 5

PANEL CONTROLS ............................................................................................................................................................. 10

GENERAL OPERATIONS .................................................................................................................................................. 13

RADIO OPERATIONS ........................................................................................................................................................ 15

DISC/USB/SD/MMC OPERATIONS .............................................................................................................................. 17

SYSTEM SETUP .................................................................................................................................................................. 20

HANDLING COMPACT DISCS ........................................................................................................................................ 22

CLEANING ............................................................................................................................................................................ 22

TROUBLESHOOTING GUIDE .......................................................................................................................................... 23

SPECIFICATION ................................................................................................................................................................. 25

Important safeguards

Read carefully through the manual to familiarize yourself with this unit. Keep this manual handy as a reference for operating procedures and precautions. Do not allow persons

who have not read through this manual to use this unit.

“CLASS 1 LASER PRODUCT”

This product contains a laser diode of higher class than 1. Laser beams from the optical pickup are dangerous to the eyes. To ensure continued safety, do not remove any covers or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel.

Do not allow this unit to come into contact with liquids. Electrical shock could result. Also, damage to this

unit, smoke, and overheating could result from contact with liquids or dust. Protect this unit from moisture.

Make sure that foreign objects do not get inside the unit; they may cause malfunctions, or create safety

hazards such as electrical shock or laser beam exposure.

The beginning of operation is the moment of the unit installation. Before use the device in winter it is

recommended to heat up the passenger compartment during 20 seconds or to the operation temperature.

Using the unit with the temperature that goes beyond the operation temperature greatly decreases the

operation resource of the screen and other components of the unit and can result in an outage.

Disconnect the vehicle’s negative battery terminal while mounting and connecting the unit. The unit is designed for negative terminal of the battery, which is connected to the vehicle metal. Please

ensure it before installation.

When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher

amperage rating may cause serious damage to the unit.

Do not allow the speaker wires to be shorted together when the unit is switched on. Otherwise it may

overload or burn out the power amplifier.

Make sure you disconnect the power supply and aerial if you will not be using the system for a long period

or during a thunderstorm.

Make sure you disconnect the power supply if the system appears to be working incorrectly, is making an

unusual sound, has a strange smell, has smoke emitting from it or liquids have got inside it. Let a qualified technician check the system.

Always keep the volume low enough so that you can hear sounds from outside the vehicle. Should this product fail to operate properly, contact your dealer or nearest service center.

Accessories

1. Receiver 1 pc

2. Front panel 1 pc

3. Protective case 1 pc

4. Remote controller 1 pc

5. ISO connector 1 pc

6. Mounting parts: Nut 1 pc Spring washer 2 pcs Flat washer 2 pcs Screw M5 1 pc Screw M5x5 1 pc Metal strap 1 pc Release key 2 pcs

7. Instruction manual 1 pc

8. Warranty card 1 pc

9. Consumer information 1 pc

Installation/Connections

Choose the mounting location where the unit will not interfere with the normal driving function of the

driver.

Before finally installing the unit, connect the wiring and make sure that the unit works properly. Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the

vehicle.

Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a

sudden stop, like an emergency stop.

If installation angle exceeds 30° from horizontal, the unit may not perform properly. Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or

from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration.

Din Front/Rear-Mount

This unit can be properly installed either from 'Front' (conventional DIN Front-mount) or 'Rear' (DIN Rearmount installation, utilizing threaded screw Holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods.

DIN FRONT-MOUNT (Method A)

1. Car dashboard

2. Sleeve

3. Screw

4. Nut

5. Spring washer

6. Screw

7. Metal strap

8. Flat washer

1. Install the sleeve into the dashboard; ensure it is installed with the correct side and there are no

obstacles (wires, dashboard elements, etc) for the unit installation.

2. After installing the sleeve into the dashboard, bend tabs fitting to the size of the

dashboard to fix the sleeve in place.

3. Use the metal strap to fix the rear side of the unit. Determine a place for fixing

and install the strap as shown in the picture. You can bend the strap to the needed angle with your hands.

4. Make the necessary wire connections. Ensure the connections are correct.

5. Install the unit into the sleeve until the side locks are fixed.

Dismantling the unit

а – Trim frame б – Frame uninstall direction в – Release key insertion

1. Switch off the unit and detach the front panel.

2. Insert your fingers into the groove in the front side of the trim frame

(apply some effort to detach the frame). Pull the frame to detach it.

3. Insert the supplied release keys into the both sides of the unit body to click,

as shown in the picture. To extract the unit from the dashboard, pull the release keys or the unit body to pull it out. Before detaching the unit, ensure it is not fixed with the metal strap.

Trim frame installation

To install the trim frame, press it to the unit body and push it to fix it in place. This should be done before installing the front panel; otherwise you are not able to install the trim frame. When the trim frame being installed, the side with the groove should face down and fixed first.

2. DIN REAR-MOUNT (Method B)

For this method, use the screw holes in the lateral sides of the unit. Fix the unit with the help of the factory radio mounting brackets.

1. Select a position in which the screw holes of the brackets (3) are aligned with the screw holes in the unit body, and screw in two screws (2) in each side.

2. Screw.

3. Factory radio mounting brackets.

4. Vehicle dashboard.

5. Lock (remove this part). Note: The outer trim frame and mounting sleeve are not used for method of installation.

Detachable front panel

Install the fastening hole on the right side of the front panel in the right fastening of the unit. Then insert the left fastening on the panel into the fixing hole on the left part of the unit. Press on the upper right part of the panel until a click. Ensure that the panel is properly fixed. To detach the front panel, press OPEN button, then distract the left side of the panel from the fastening of the unit.

Anti-theft system

The front panel of this unit can be stored in the included protective case when not in used and carried away when you leave the vehicle to deter theft. Switch off the power of the unit. Detach the front panel, then put it to the protective case and take it with you. Cautions: The control panel can easily be damaged by shocks. After removing it, place it in a protective case and be careful not to drop it or subject it to strong shocks. The rear connector that connects the main unit and the control panel is an extremely important part. Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc. Note: If the control panel is dirty, wipe off the dirt with soft, dry cloth only. And use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the control panel.

Connection diagram

Notes:

In spite of having any kinds of speaker system, must use 4 ohms impedance of speaker to reduce the

distortion during high volume level.

Prohibited to make the conductors of auto antenna and ground touch with each other.

Using the ISO Connector

1. If your car is equipped with the ISO connector, then connect the ISO connectors as illustrated.

2. For connections without the ISO connectors, check the wiring in the vehicle carefully before connecting, incorrect connection may cause serious damage to this unit.

Cut the connector, connect the colored leads of the power cord to the car battery as shown in the colour code table below for speaker and power cable connections.

Parking wire connection

Note: The parking brake wire must be connected in order to watch video on this unit. If that wire has not been connected then a

“PARKING BRAKE” message will appear on the LCD screen.

Panel controls

Front panel

1. POWER button

2. PLAY/PAUSE/CH 1-6 button

3. MOD button

4. VOL multifunctional button

5. EQ button

6. TFT display

7. OPEN button

8. USB port

9. IR sensor

10. NEXT button

11. APS button

12. SEL button

13. PREVIOUS button

14. BAND button

15. MUTE button

16. AUX-IN jack

Inner panel

Press OPEN button on the front panel to detach it.

1. SD/MMC memory card slot

2. EJECT button

3. RESET button (hole)

Pressing RESET hole will erase the clock setting and stored stations. Panel status indicator lights up when you slide the panel down, flashes when you remove the panel.

Remote controller

1. CLK button

2. MODE button

3. STOP button

4. SETUP button

5. MO/ST button

6. LO/DX button

7. REPEAT button

8. GOTO button

9. PREVIOUS/NEXT button

10. SEL button

11. VOL+/VOL- buttons

12. Cursor buttons

13. MENU/SUBWOOFER button

14. BAND (OSD) button

15. POWER button

16. PLAY/PAUSE button

17. MUTE button

18. TITLE/PBC (A/PS) button

19. ZOOM button 25. 4/RDM button

20. ANGLE button 26. +10 button

21. EQ button 27. 0/TA button

22. FAST FORWARD button 28. 9/AP button

23. ENTER button 29. 3/INT button

24. REWIND button 30. 1/TOP button

Changing the battery

1. Press the catch and at the same time pull out the battery tray.

2. Insert the 1 x lithium battery with (+) mark facing up. Insert the battery tray into the remote control.

General operations

Opening the front panel

Press the OPEN button to flip down the front panel. Now you can insert CDs into the CD compartment and eject them by pressing EJECT button.

Reset the unit

Operating the unit for the first time or after replacing the car battery, you must reset the unit. Press RESET button (hole) with a pointed object, such as a ballpoint pen, to set the unit to initial state. Note: When some errors occur, you can also press RESET button to resume to normal, and it will erase some memorized functions.

Turning the unit on/off

Press POWER button on the panel or the RC to turn on the unit. Press POWER button on the panel or on the RC again to turn the unit off.

Mode selection

Repeatedly press MOD button on the panel or MODE button on the RC to select a mode: Radio => Disc => USB => Memory card => AUX. Note: The Disc, Card and USB modes are only available when corresponding storages are connected to the unit.

Mute function

Press MUTE button on the RC to turn off the sound. “MUTE ON” appears on the display. Press the button

again or adjust volume to resume the sound output.

Volume control

Press VOL+/VOL- buttons on the RC or rotate VOL regulator on the panel to decrease or increase sound volume level.

TFT monitor adjustment

Press SEL button on the front panel or on the RC to access Picture mode selection menu: COLOR => BRIGHTNESS => CONTRAST => TINT. Use VOL+/VOL- buttons/regulator to adjust the selected mode.

Audio quality adjustment

Press SEL button on the front panel or on the RC to switch between BASS, TREBLE, BALANCE, FADE and VOLUME. Press and hold SEL button to display REG, then press the button repeatedly to switch between PI, TA, AF, SWF, EQ, LOCAL/DX(in radio mode), STEREO/MONO(in radio mode), CLK FMT, SET CLK, FREQUENCY AREA, ANIMATION and WALLPAPER. Use VOL knob to adjust.

Animation

In RADIO mode press and hold SEL button on the front panel or on the RC for 2 seconds, choose ANIMATION and select the playing time of the animation: OFF => 10s => 30s =>

EQ modes

Press and hold SEL button on the panel or SEL button on the RC until the display shows ROCK. Press VOL+/VOL- buttons on the RC or rotate VOLUME regulator on the panel to choose an equalizer effect: ROCK => USER => JAZZ => CLASSIC => POP. After you have reached your desired effect, leave the unit idle in order for the new setting to take effect.

Loudness

Press repeatedly SEL button on the panel or SEL button on the RC until the display shows LOUDNESS ON (LOUDNESS OFF). Press VOL+/VOL- buttons on the RC or rotate VOLUME regulator on the panel to select between LOUDNESS ON/LOUDNESS OFF. LOUDNESS function is to emphasize the bass output; the word LOUDNESS ON indicates that the LOUDNESS mode is on.

Clock setting

Press CLK button on the RC to show the time on the display.

AUX in jack

AUX-in jack is intended for connecting external audio equipment to amplify the sound. If connection is made correctly, the audio signal from the external source will be translated through the acoustics of the head unit. This enables to adjust the volume and quality of the sounding. For example, you can connect an MP3-player to listen to tracks using the car acoustic system.

Setting the background

Press and hold SEL button on the panel or SEL button on the RC and select BACKGROUND COLOR. Use VOL+/VOL- buttons/regulator to change background color between AUTO, GREEN, YELLOW, RED, LIGHT BLUE, BLUE and PINK. If you set the background color to AUTO, the device will change colors automatically.

The brake function

If the parking brake is not engaged, a “parking brake” warning will flash on the screen, and video playback

will not start. Audio playback will be still available. This warning appears only in case if the parking brake wire is connected to the parking brake system of the car.

Rear view camera

After connecting the rear view camera, the image will be automatically displayed on the screen of the unit when you set gear on Reverse.

Radio operations

Band select

Press BAND button on the panel or BAND (OSD) button on the RC to select your desired radio band in Radio mode: FM1, FM2, FM3, AM1 (MW1), AM2 (MW2).

Auto/Manual tuning

Manual tuning: Press UP/DOWN joystick buttons on the RC to manually adjust the radio frequency. Auto tuning: Press and hold UP/DOWN joystick buttons on the RC for 2 seconds, the radio will seek to the

next up or down strong and clear frequency station automatically. Repeat this action to seek for other desired stations.

Programming tuner stations

There are six numbered preset buttons, under which you can store and recall stations for each band. Select the needed frequency, then press and hold a preset button. The station will be saved in the memory under the corresponding number. To recall a stored station, press the corresponding preset button.

Automatic store/preset scan

Automatic store: Press and hold APS button on the panel or A/PS button on the RC. The radio will

automatically store the 6 strongest available stations to the 6 preset memories of the current band. To stop auto store, press this button again.

Preset scan: Press APS button on the panel or A/PS button on the RC. The receiver will scan the saved

stations in all bands for 5 seconds.

Mono/Stereo control (in FM radio mode)

Press ST/MO button on the RC to select MONO or STEREO mode.

Local radio station search

Press LOC/DX button on the RC to choose between the local and long-distance stations.

Storing Stations in memory

This system can keep in 6 memory slots up to 30 stations. Select the needed frequency band(FM1/FM2/FM3/AM1(MW1)/AM2(MW2)) and then select the station. Press and hold one of 1-6 buttons on the RC until the broadcast is heard again after an interruption.

RDS operations

TA function: Press TA/AF button to activate/deactivate this function. If the FM station is transmitting the

latest traffic announcement, the device will automatically interrupt any playback an display TRAFFIC on the screen. After the end of the announcement the device will resume playback.

AF function: Press and hold TA/AF button to turn this function ON/OFF. The radio will automatically switch

to the AF station with stronger signal if available an display a message “NEW FREQUENCY”.

PTY operation

Press and hold MU/PTY button to select the type of the program (NEWS, POP etc.)

DISC/USB/SD/MMC operations

AUX operation

Connect your external device to the AUX input on the front panel via AUX cable. Press MODE button repeatedly until you select AUX mode. You can adjust volume with VOL button.

USB operation

Play/Pause/Stop

During playback press PLAY/PAUSE button on the RC to pause playback. Do this operation again to resume playback. To stop playback, press STOP button on the RC.

Selecting tracks/chapters

During playback press PREVIOUS button on the panel or on the RC to play the previous track/chapter (depending on the format). Press NEXT button on the panel or on the RC to play the next track/chapter.

Fast forward/rewind

Press and hold PREVIOUS or NEXT button on the panel or RC for fast backward or forward playing correspondingly. While fast playback, press PLAY/PAUSE button on the RC or PLAY/PAUSE/CH 1-6 button on the panel to resume normal speed.

Repeat playback

For digital video: Press REPEAT button on the RC to select the repeat mode as follows. CHAPTER REPEAT

ON => TITLE REPEAT ON => REPEAT ALL => REPEAT OFF.

For VCD/CD: REPEAT button on the RC to select the repeat mode as follows. REPEAT ONE => REPEAT

ALL => REPEAT OFF.

+ 37 hidden pages