Sorelle Urban Changing Table, Berkley Changing Table Assembly Instruction Manual

Made in HY, China

Important Information:

Assembly Instruction

Read all instructions

By Sorelle - A Division of C & T International, Inc.

46 Whelan Road, East Rutherford, N.J.07073 U.S.A.
Tel, [phone] Fax, [phone]

BEFORE assembling Changing Table.

KEEP INSTRUTIONS FOR FUTURE USE.

Urban Changing Table

Website: www.sorellefurniture.com

Page 2

51 Urban Changing Table Instruction Sheet

Sorelle

TC

HB

A

Changing Table Warnings:

WARNING

FALL HAZARD - to prevent death or serious injury, always keep child within arm’s reach.
Read all instructions before use of the changing table.
KEEP THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE USE.
Inspect the changing table periodically. Do not use the changing table if it is damaged or
broken. Contact C&T International Inc. with any questions.
Tighten all loose screws and bolts before each use.
The maximum recommended weight of the child is 30lbs for the changing table.
Use only the pad provided by C&T International / Sorelle or Manufacturer’s
Always secure the pad to the changing surface. See Instructions.
NEVER use crib without Changing Table attached

AU

BE A

A THI

NOTES ON ASSEMBLY:

-During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on
the diagram of the item which is drawn actual size and design. Be sure to use the proper size and shape
specified in the instructions.

-To assemble this unit you may be required to place the unit on it’s side and face. It is strongly
recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.

NOTES ON CARE AND MAINTENANCE:

- Do not scratch or chip the finish.

- Inspect the product periodically, contact C&T International / Sorelle for replacement parts or questions.

- Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a
damp, cold basement. These extremes can cause a loss of structural integrity.

-To preserve the luster of the high quality finish on your product, it is recommended to place a daily or
felt pad under any items you place on the finish.

-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.

-Do not use abrasive chemicals.

-Do not spray cleaners directly onto furniture.

-Lift slightly when moving on carpeting to prevent leg breakage.

-Use of a vaporizer near furniture will cause wood to swell and finish to peel.

NOTES ON USE:

Keep children and others safe by following these simple rules:

- Do not allow any child to play on furniture

- Do not allow climbing on any piece of furniture.

- Do not allow hanging from any piece of furniture.

- Always monitor your child’s activity when in the nursery.

WHEN CHILD REACHES A MAXIMUM WEIGHT OF 30 LBS.,
THE CHANGING TABLE SHALL NO LONGER BE USED

Page 3

51 Urban Changing Table Instruction Sheet

Sorelle

C
B

A

A

BE

A T

PARTS LIST

Important: In order to properly assemble the changing table, carry out the operations in order specified. Failure to assemble the changing table in the manner
recommended could make the changing table hazardous

1x1x

16x

No.
A
B
C
C1
D
D1
E
E1
F
G
H

I
J
K

Description

Back Frame
Front Frame
Left Non-grooved Rail
Right Non-grooved Rail
Left Upper Grooved Rail
Right Upper Grooved Rail
Left Grooved Rails
Right Grooved Rails
Top Shelf
Shelfs
M6 * 30mm Bolts
Changing Pad
Safety Harness

Allen Key

Qty
1
1
1
1
1
1
2
2
1
2
16
1
1
1

A

Tool required

ASSEMBLY INSTRUCTIONS

H

B

I

1x

K

C1

F

G

G

E

E1

E1

C

E

D

D1

J

*THIS PRODUCT MAY BE DIFFERENT FROM

THE INSTRUCTION SHEET SHOWN*

2x2x

2x

S T U

S
T
U

16mm (5 / 8 ”) Bolts
Washers
Nuts

2
2
2

A

C1

E

E

C

D

D1

Page 4

51 Urban Changing Table Instruction Sheet

Sorelle

Changing Table Assembly Steps

Step 1

Figure 1

Figure 2

Connect Rails to Back Frame as Figure 1 shows.

c

H

H

H

H

H

H

H

H

Step 2

Shelves Assembled as Figure 2 shows.

Slide the shelves through the grooves in the
Rails and Back Frame .

F

G

G

E1

E1

B

Figure 4

H

H

H

H

H

H

H

H

Step 4

Safety Harness Assembled as Figure 4 shows.

Page 5

51 Urban Changing Table Instruction Sheet

Sorelle

Changing Table Assembly Steps

Step 3

Figure 3

Tighten all Bolts

Connect Front Frame To Changing Table as Figure 3 shows.

SAFETY HARNESS/RESTRANT SYSTEM USE

1. Place the infant on the changing table foam pad

2. Position the safety harness over the middle of the
infant’s torso and insert the buckled ends into each
other until they lock shut with a click.

3. Gently pull the loose end of the safety to lightly snug
the safety harness around the infant.

Step 1
To attach the safety harness, place the safety harness (Part “J”)
on the top shelf and align the hole on the safety harness end with
the hole on the top shelf

Step 2
Insert the bolt (Part “S”) through a washer
(Part “T”), the harness hole and the top shelf
hole.

Step 3
Secure with a nut (Part “U”) on the underside
of the top shelf.

Step 4
Repeat the process to attach the other side
of the harness to the top shelf.

Step 5
Place changing pad on top of safety harness.

S

S

T

U

U

J