Sony ZL31 User Manual

For assistance and information

call toll free I-800-BUY-AIWA

8Z-MA4-91 3-11 981 115BKM-Y-9

(United States and Puerto Rico)

mil!i

DIGITALAUDIO

Am!!!!!m

“CAUTION:TO REDUCE THE RISK OF

ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.”

Explanation of Graphical Symbols:

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated

●

Owner’s record ~

For your convenience, record the model number and serial number (you will find them on the rear of your unit) in the space provided below. Please refer to them when you contact your Aiwa dealer in case of difficulty.

~ Model No. I CX-ZL31 I

I SX-WZL60

I PX-E860 I I

Read the Operating Instructions carefully and completely before operating the unit. Be sure to keep the Operating Instructions for future reference. All warnings and cautions in the Operating Instructions and on the unit should be strictly followed, as well as the safety suggestions below.

Installation

Water and moisture — Do not use this unit near water, such as near a bathtub, washbowl, swimming pool, or the like.

Heat — Do not use this unit near sources of heat, including

heating vents, stoves, or other appliances that generate heat. It also should not be placed in temperatures less than 5°C (41‘F) or greater than 35°C (95°F). Mounting surface — Place the unit on a flat, even surface.

“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the

presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Serial No. (Lot No.)

I I

Ventilation — The unit should be situated with adequate space around it so that proper heat ventilation is assured. Allow 10 cm (4 in.) clearance from the rear and the top of the unit, and 5 cm (2 in.) from each side.

- Do not place the unit on a bed, rug, or similar surface that may block the ventilation openings.

- Do not install the unit in a bookcase, cabinet, or airtight rack where ventilation may be impeded.

Objects and liquid entry — Take care that objects or liquid do not get inside the unit through the ventilation openings.

Carts and stands — When placed or mounted on a stand or cart, the unit should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the unit or cart to overturn or fall.

Condensation — Moisture may form on the CD pickup lens when:

- The unit is moved from a cold spot to a warm spot

- The heating system has just been turned on

- The unit is used in a very humid room

- The unit is cooled by an air conditioner

When this unit has condensation inside, it may not function normally. Should this occur, leave the unit for a few hours, then try to operate again. Wall or ceiling mounting —The unit should not be mounted

on a wall or ceiling, unless specified in the Operating Instructions.

Electric Power 1 Power sources — Connect this unit onlv to Dower sources

specified in the Operating Instructions, an-das’marked on the unit. Polarization — As a safety feature, some units are equipped

with polarized AC power plugs which can only be inserted one way into a power outlet. If it is difficult or impossible to insert the AC power plug into an outlet, turn the plug over and try again. If it is not still inserted easily into the outlet, please call a qualified service technician to service or replace the outlet. To avoid defeating the safety feature of the polarized plug, do not force it into a power outlet.

AC power cord

- When disconnecting the AC power cord, pull it out by the AC power plug. Do not pull the cord itself.

- Never handle the AC power plug with wet hands, as this could result in fire or shock.

- Power cords should be firmly secured to avoid being severely bent, pinched, or walked upon. Pay particular attention to the cord from the unit to the power socket.

- Avoid overloading AC power plugs and extension cords beyond their capacity, as this could result in fire or shock.

Extension cord — To help prevent electric shock, do not use a polarized AC power plug with an extension cord, receptacle, or other outlet unless the polarized plug can be completely inserted to prevent exposure of the blades of the plug. When not in use — Unplug the AC power cord from the power

outlet if the unit will not be used for several months or more. When the cord is plugged in, a small amount of current continues to flow to the unit, even when the power is turned off.

[ (Al

AA*

ENGLISH

Outdoor Antenna 1 Power lines — When connecting an outdoor antenna, make

sure it is located away from power lines.

2 Outdoor antenna grounding — Be sure the antenna system

is properly grounded to provide protection against unexpected voltage surges or static electricity build-up. Article 810 of the National Electrical Code, ANS1/NFPA 70, provides information on proper grounding of the mast, supporting structure, and the lead-in wire to the antenna discharge unit, as well as the size of the grounding unit, connection to grounding terminals, and requirements for grounding terminals themselves.

Antenna GroundingAccordingtothe National ElectricalCode

, ANTENNA LEAD IN WIRE

z’

ANTENNA DISCHARGE

(NEC SECTION 810-20)

ELECTRIC SERVICE EQUIPMENT

NEC-NATIONAL ELECTRICAL CODE

, / ELECTRODE SYSTEM

GROUNDING CONDUCTORS

GROUND CLAMPS

POWER SERVICE GROUNDING

(NEC ART 250 PART H)

Maintenance

Clean the unit only as recommended in the Operating Instructions.

PREPARATIONS

CONNECTIONS

REMOTE CONTROL ...........................................................6

BEFORE OPERATION ........................................................6

................................................................. 4

SOIJND

AUDIO ADJUSTMENTS ....................................................

GRAPHIC Equalizer .......................................................9

RADIO RECEPTION

MANUAL TUNING .............................................ms............. 10

PRESETTING STATIONS ................................................ 11

TAPE PLAYBACK

BASIC OPERATIONS ......................................................

CD PLAYING

BASIC OPERATIONS ...................................................... 12

PROGRAMMED PLAY ..................................................... 14

RECORDING

BASIC RECORDING ........................................................ 15

Al EDIT RECORDING ...................................................... 16

PROGRAMMED EDIT RECORDING ...............................

Damage Reuuirina Service

Have the units serviced by a qualified service technician if:

- The AC power cord or plug has been damaged

- Foreign objects or liquid have got inside the unit

- The unit has been exposed to rain or water

- The unit does not seem to operate normally

- The unit exhibits a marked change in performance

- The unit has been dropped, or the cabinet has been damaged DO NOT ATTEMPT TO SERVICE THE UNIT YOURSELF

CLOCK AND TIMER

SETTING THE CLOCK ..................................................... 18

SETTING THE SLEEP TiMER ......................................... 18

SE:TTING THE TIMER ...................................................... 19

TURNTABLE

BASIC OPERATION .................................................m....... 20

OTHER CONNECTIONS

CONNECTING OPTIONAL EQUIPMENT ....................... 21

LISTENING TO EXTERNAL SOURCES ......................... 21

GENERAL

CARE AND MAINTENANCE ........................................... 22

TROUBLESHOOTING GUIDE ......................................... 22

SPECIFICATIONS

PARTS INDEX ................................................... Back cover

............................................................

ENGLISH

your system and accessories

Check

E!2!.-

CX-ZL31 Compact disc stereo cassette receiver SX-WZL60 Front speakers PX-E860 Stereo turntable

Remote control AM antenna

Operating Instructions, etc.

FM antenna

1 Connect the right speaker to the main unit.

Connect the speaker cord with the plug to the SPEAKERS

HIGH FREQ R terminal.

@ Connect the speaker cord with the white stri~e to the

SPEAKERS LOW FREQ R 0 terminal and the black cord

O terminal.

to the

. ,4

.,. @

Before connecting the AC cord

The rated voltage of your unit shown on the rear panel is 120 V AC. Check that the rated voltage matches your local voltage.

IMPORTANT

Connect the speakers, antennas, and all optional equipment first, Then connect the AC cord.

There are no difference between the front speakers. Both speakers can be connected as L (left) or R (right).

AM antenna

Right speaker

FM antenna

2 Connect the left speaker to the main unit.

Connect the speaker cord with the plug to the SPEAKERS

HIGH FREQ L terminal, and another sDeaker cord to the SPEAKERS LOW FREQ L terminals in the same manner as step 1.

4 ENGLISH

~+5

AC cord

Connect the stereo turntable to the main unit.

Connect the red plug to PHONO IN R jack, and the white plug to PHONO IN L jack.

● Be sure to connect the speaker cords correctly. Improper

connections can cause short circuits in SPEAKERS terminals. ,,~

, *’-

,0°

II@

Connect the supplied antenhas.

Connect the FM antenna to FM 75 Q terminals and the AM antenna to AM LOOP terminals.

/..,

;,:J

FM antenna

5 Connect the AC cord to an AC outlet.

● The game Demo will begin when the AC cord is plugged

into an AC outlet. See page 8 “Game Demo” for details.

To position the antennas

FM antenna:

Extend the antenna horizontally in a T-shape and fix its ends to the wall. AM antenna: Position to find the best reception.

● Do not leave objects generating magnetism, such as credit

cards, near the speakers, as the objects may be damaged.

● Do not bring the FM antenna near metal objects or curtain rails.

● Do not bring the AM antenna near other optional equipment,

the stereo system itself, the AC cord or speaker cords, since noise will be picked

● Do not unwind the AM antenna wire.

up.

,., ,

CONNECTING AN OUTDOOR ANTENNA--

For better FM reception, use of an outdoor antenna is recommended. Connect the outdoor antenna to FM 75 Q terminals.

7r Flvl

‘

stand the AM antenna on a surface

Fix the claw to the slot.

To connect other optional equipment+ page 27.

ENGLISH

Inserting batteries

Detach the battery cover on the rear of the remote control and insert two R6 (size AA) batteries.

R6(AA)

When to replace the batteries

The maximum operational distance between the remote control and the sensor on the main unit should be approximately 5 meters (16 feet). When this distance decreases, replace the batteries

with new ones.

To use SHIFT on the remote control

Buttons @)have two different functions. One of these functions is indicated on the button, and the other on the plate above the button. To use the function on the button, simply press the button. To use the function on the plate above the button, press the button while pressing SHIFT.

To use

FUNCTION on the remote control

FUNCTION substitutes for the function buttons (TAPE, TUNER/

BAND, PHONO, VIDEO/AUX, CD) on the main unit.

Each time FUNCTION is pressed, the next function is selected cyclically.

To turn the unit on

Press one of the function buttons (TAPE, TUNER/BAND,

PHONO, VIDEO/AUX, CD). Playback of the inserted disc begins,

or the previously tuned station is received (Direct Play Function). POWER is also available.

To turn the power off Press POWER.

Illumination guide

Whenever POWER or one of the function buttons is pressed, the buttons for the selected operation light up or flash.

Flash window

The window on the top of the unit lights up or flashes while the unit’s power is on. To turn off the light of the top window, press

CD. To turn back on, repeat the above.

■ while pressing

FUNCTION

● If the remote control is not going to be used for an extended

period of time, remove the batteries to prevent possible electrolyte leakage.

● The remote control may not operate correctly when:

- The line of sight between the remote control and the remote sensor inside the display window is exposed to intense light, such as direct sunlight

- Other remote controls are used nearby (those of a television, etc.)

When you press CD to turn on/off the flash window, the BLANK SKIP PLAY is also switched to ON/OFF.

To change the brightness level of the display

Press ECO so that “ECO MODE” is displayed.

Within 4 seconds, turn MULTI JOG to display “DIM MODE”, and then press ENTER within 4 seconds.

Within 4 seconds, turn MULTI JOG to select the dimmer mode as below. The mode will be automatically set after 4 seconds. It will also be set if ENTER is pressed within 4 seconds after step

DIM-OFF* DIMMER l* DIMMER 2 * DIMMER 3

DIM-OFF: The normal display. DIMMER 1: The illumination of the display is dimmer than usual. DIMMER 2: The illumination of the display is dimmer than

DIMMER 1. DIMMER 3: The illumination of the display is dimmer than

DIMMER 2. The spectrum analyzer, the window on the top of the unit, and the button lamps light off.

6 ENGLISH

4-CHANNEL MULTI-AMPLIFIER SYSTEM

To provide reinforcement for the ultra-low frequencies, in addition to the Left/Right 2-channel amplifier used to reproduce mid-to-

high-range frequencies, this system incorporates a second L/R 2-channel amplifier just for reproduction of ultra-low frequencies

— making it, in effect, a 4-amplifier system. By utilizing discrete

amplifiers for mid to-high-frequencies and low frequencies, highquality sonic reproduction that is virtually free from distortion can be realized. This Multi Amplifier System, which utilizes independent circuitry for the different frequency ranges, enables superb sonic

reprc)duction free from distortion.

SETTING POWER ECONOMIZING MODE

Setting this unit to power economizing mode reduces power consumption as follows.

● When the power is turned off, all the display lights turn off, and

only the @3TANDf3Y/ON indicator lights.

However, if the clock is not set, the game Demo (page 8) will

begin when the power is turned off.

● If CD or Tape does not play for 10 minutes or if there is no

audio input from any connected external equipment for 10 minutes when VIDEO/AUX or PHONO is selected as the source,

the power shuts off.

● The display brightens only when operating the unit. When the

unit has not been used for 10 seconds, the brightness level switches to the mode previously selected in “DIM MODE”. (Page

6) (If the display brightness level is set to “DIM-OFF”, the

brightness does not change. When the level is “DIMMER 3“, the button lamps are also turned off.)

Press ECC).

“ECO MODE” will be displayed.

Press ENTER within 4 seconds.

The current power-economizing mode status will be displayed.

If the power-economizing mode is OFF: ECO OFF If the power-economizing mode is ON: ECO ON

BUILT-IN SUBWOOFER SYSTEM

The built-in subwoofer System has a separate subwoofer cavity

area that is part of the loudspeaker cabinet structure, which acts as a sonic filter to cut distortion components. (In the Multi Amplifier System, the ultra-low frequency signals transmitted from their own independent amplifier are reproduced in this area.) This separate construction gives a clear, rich definition to bass reproduction and it can realize clear, well-defined mid-to-high frequency signals. And AlWA’s built-in subwoofer system incorporates a subwoofer capable of powerful, satisfying bass performance with true stereo separation.

Subwoofer Cavity area

Amplifiers for Low frequencies

Turn MULTI JOG within 4 seconds to switch the

power-economizing mode on or off.

Example: When “ON” is selected

The mode will be automatically set after 4 seconds. It will

also be set if ENTER is pressed within 4 seconds after step

.5.

Standby power consumption

If the power-economizing mode is OFF: 17 W If the power-economizing mode is ON: 1.7 W

To view the clock when all the display lights turn off, press II so that the time is displayed for 4 seconds.

ENGLISH

To reset the game Demo

Press DEMO twice, then press P. The game starts again.

To change the probability of equalizing the three numbers

Press + or - repeatedly to select one of the three probability levels when playing the game Demo. The tray number indicator in the display changes between 1 and 3. As the tray number increases from 1 to 3, the higher the probability of equalizing.

Ill

“’”d

When the AC cord is plugged into an AC outlet for the first time after purchase, the game Demo will begin in the display. When

the power is turned on, the game Demo will end. When the power

is turned off, the game Demo will begin again. Until the clock is set, the game Demo will begin whenever the power is turned off.

When the clock is set, the game Demo will not begin even if the

power is turned off. (See “SETTING THE CLOCK on page 18.)

To start or end game Demo when the clock is set

Press DEMO when the power is off, the game Demo will begin.

To end the game Demo, press DEMO again.

To play the game Demo 1

Press DEMO so that the game Demo displays.

Press ~. Three numbers on the display start to run.

■ once.

Press

The number on the left side stops. Press W twice to stop the remaining two numbers.

4 Scoring:

20 points are given to start the game. If all the numbers are eaual, 50 points are added to the score. If not equal, one point is subtracted. If the gained points reach 9999, you win. If the gained points fall to O, you lose.

● During the game Demo, ■ , +, - and > are available

only for the game Demo. Cancel the game Demo to use these buttons for the functions such as CD playing, etc.

● During the game Demo, some indicators unrelated with the

actual operation light up on the display.

8 ENGLISH

VOLUME.

PHONES

VOLUME CONTROL

Turn VOLUME on the main unit, or press VOL A or V on the remote control.

The volume level is displayed as a number from Oto MAX (50). The volume level is automatically set to 20 when the power is

turned off with the volume level set to 21 or more.

This unit provides the following three different equalization curves. ROCK: Powerful sound emphasizing treble and bass POP: More presence in the vocals and midrange CLASSIC: Enriched sound with heavy bass and fine treble.

Press GEQ repeatedly to select the equalization mode.

The GEQ mode is displayed cyclically as follows.

ROCK—

POP— CLASSIC— GEQ OFF

(cancel)

SUPER T-BASS SYSTEM

The T-BASS system enhances the realism of low-frequency sound.

Press T-BASS.

Each time it is pressed, the level changes. Select one of the three levels or the off position to suit your preference.

To select with the remote control

Press T-BASS while pressing SHIFT.

Low frequency sound may be distorted when the T-BASS system is used for a disc or tape in which low frequency sound is already emphasized. In this case, cancel the T-BASS system.

The selected equalization mode is displayed.

To cancel the selected mode

Press GEQ repeatedly until ‘(GEQ OFF is displayed.

To ~elect With the remote control

Press GEQ repeatedly while pressing SHIFT.

MULTI JOG is also availableto changethe equalizationmode

Using the headphones

Connect headphones to PHONES jack with a standard stereo plug (a6.3 mm, No sound is output from the speakers while the headphones are plugged in.

‘/4 inch).

ENGLISH

To search for a station quickly (Auto Search)

Press TUNER PRESET repeatedly to display “SEARCH” (auto search mode), counterclockwise until the frequency starts to change rapidly. After tuning into a station, the search stops.

To stop the Auto Search manually, turn MULTI JOG a little in either direction.

● The Auto Search may not stop at the stations with very weak

signals.

● +4 DOWN and -UP are also available to search for a

station. Keep + DOWN or -UP pressed until the tuner starts searching. Press the button to stop the search manually.

and turn MULTI JOG clockwise or

PressTUNER/BAND to select the FM or AM band.

When TUNER/BAND is pressed while the power is off, the

power is turned on directly (Direct Play Function).

To select a band with the remote control

Press BAND while pressing SHIFT.

Press TUNER PRESET repeatedly to select the

manual tuning mode.

Each time the button is pressed, the following three tuning modes are selected cyclically. @l Preset tuning @ Auto @

search mode:“SEARCH” is displayed.

Manual tuning mode: “SEARCH” is not displayed and

mode:The preset number flashes.

the preset number does not flash.

Frequency SEARCH

Preset number

m The preset tuning mode is skipped if no station is preset.

Turn MULTI JOG clockwise or counter-clockwise

to tune in to a station.

The frequency changes as you turn MULTI JOG. When a station is received, “TUNE” is displayed for 2 seconds.

FM stereo reception, 1110111is displayed.

During

When an FM stereo broadcast contains noise

Press MONO TUNER on the remote control while pressing SHIFT so that “MONO” appears on the display. Noise is reduced, although reception is monaural.

To restore stereo reception, press MONO TUNER on the remote control while pressing SHIFT so that “MONO disappears.

To change the

AM tuning interval

The default setting of the AM tuning interval is 10 kHz/step. If you use this unit in an area where the frequency allocation system is 9 kHz/step, change the tuning interval.

Press POWER while pressing E on the unit. To reset the interval, repeat this procedure.

m When the AM tuning interval is changed, all preset stations are cleared. The preset stations have to be set again.

● ++ DOWN and -UP are also available to tune in to a

station.

10 ENGLISH

MULTI JOG

..””..... .=. @

.—

I !,–-’1

i,~ ‘... --.----2

(Deck 1)

(Deck 2)

The unit can store a total of 32 preset stations. When a station is stored, a preset number is assigned to the station. Use the preset number to tune in to a preset station directly.

7 Press TUNER/BAND to select a band, and press

- DOWN or -UP to select a station.

2 Press 1I SET to store the station.

A preset number beginning from 1 in consecutive order for each band is assigned to the station.

Frequency

Preset number

3 Repeat steps 1 and 2.

No more stations will be stored if a total of 32 preset stations have already been stored.

“FULL” is displayed if you attempt to store more than 32 preset stat ions.

PRESET NUMBER TUNING

Use the remote control to select the preset number directly.

Usable tapes

Use Type I (normal) tapes only.

12PressTAPE, then press WA to open the cassette

holder.

...

■

Insert a tape with the exposed side down. Push the cassette holder to close.

Press - to start Dlaw

Only the side facing o..df;om the unit can be played back.

To stop play, press W=. To pause play, press 1I. To resume play, press again. To fast forward or rewind, press + or - in stop mode.

Then press WA to stop the tape.

When both Deck 1 and Deck 2 are set in the playback

mode

Deck 2 is heard.

1 Press BAND while pressing SHIFT to select a

band.

2 Press numbered buttons O-9 and +1Oto select a

preset number.

Example:

To select preset number 20, press +10, +10

To select preset number

15, press +10 and 5.

Selecting a preset number on the main unit

Press TUNER/BAND to select a band. Press TUNER PRESET repeatedly until the preset number flashes (preset tuning mode), and turn MULTI JOG. The preset numbers are selected

sequence as you turn MULTI JOG.

● >P13ESET is also available to select the preset number. Each

time the button is pressed, the next highest number is selected.

To clear a preset station

Select the preset number of the station to be cleared with the

numbered buttons. Then, press

■CLEAR, and press 1I SET

within 4 seconds. The preset numbers of all other stations in the band with higher numbers are decreased by one.

and O.

MULTI JOG

CD EDIT/CHECK

— ml. .

Press CD, then press A OPEN/CLOSE to open the disc compartment. Load disc(s) with the label side up.

To load one or two discs, place the disc(s) on the tray(s) in the

direction of the arrows as illustrated.

Tray number

Load discs.

~, press E. Play begins with the disc on tray 1.

Number of track being played

To rXav one disc only, press one of DISC DIRECT PLAY 1-

The selected disc is played once.

Selected disc tray, number Elapsed playing time

Number of track being played

To stop play, press To pause play, press II. To search for a particular point during playback, keep + or - pressed and release the button at the desired point. To skip to the beginning of a track during playback, turn

MULTI JOG or press + or > repeatedly. To remove discs, press AOPEN/CLOSE. ~ to be removed does(do) not face you, press DISC CHANGE

repeatedly.

■ .

To resume play, press again.

discs that face you. When the disc(s)

Elapsed playing time

DISC CHANGE

To load three to five discs, press DISC CHANGE to rotate the

trays after placing two discs. Place the next disc on empty tray. Each time DISC CHANGE is pressed, the trays rotate and one

disc can be placed.

After placing the discs, press AOPEN/CLOSE to close the disc compartment. The display shows the information of the disc to be played.

Tray number of the disc to be played

Total ;umber of tracks

Total playing time

To start play when the power is off (Direct Play Function)

Press CD. The power is turned on and play of the loaded disc(s) begins. When AOPEN/CLOSE is pressed, the power is also turned on and the disc compartment is opened.

To check the remaining time

During play, press CD EDIT/CHECK on the remote control while pressing SHIFT. The amount of time remaining until all tracks finish playing is displayed. To restore the playing time display, repeat the above.

Selecting a track with the remote control

Press one of DISC DIRECT PLAY 1-5 to select a disc.

To select disc 4 or 5, press DISC DIRECT PLAY 4 or 5 while pressing SHIFT.

2 Press numbered buttons O-9and +1O

Example: To select the 25th track, press +1O,+1Oand 5. To select the 10th track, press +10 and O. The selected track starts to play and continues to the end of

disc.

that

Replacing discs during play

While one disc is playing, the other discs can be replaced without interrupting play. 1 Press

2 Remove the discs and replace with other discs.

3 Press AOPEN/CLOSE to close the disc compartment.

DISC CHANGE.

Two discs can be replaced.

To replace the other two discs, press DISC CHANGE again.

to select a track.

12 ENGL/SH

● uen Ioadina an 8-cm (3-inch) disc, make sure to place it onto

@_~nner circle of the trav p

be damaged or the disc compartment will not open. [f it does not open, please consult your

● Do not place more than one compact disc on one disc tray.

● Do Inot tilt the unit with discs loaded, Doing so may cause

malfunctions.

● When transporting the unit, remove the discs from the trays.

● When replacing the discs during play, do not replace discs other

than those facing you.

If you place a disc on the empty right inner tray, and then press = OPEN/CLOSE, “ERROR” is displayed and the disc

compartment may not close. Remove the disc on that tray.

● Do not use irregular shape CDs (example: heart-shaped,

octagonal ones). It may result in malfunctions.

Never place here.

Use the remote control.

RANDOM play

All the tracks on the selected disc or all the discs can be played

randomly.

recisely. Otherwise, the disc may

Aiwa dealer for repair.

The silent portions between tracks recorded on a CD can be , :, skipped during playback.

r)~~~~ CD BLANK SKIP ~~ the main ~nit.

‘;*

,, ‘-!,

;’ ‘“:,

~,”.

“(CDBLANK SKIP ON” is displayed and a small dot will appear in the display.

Sm~ll dot

2 F%ess > to start playback.

The silent portions between tracks will be skipped, and the sound will be played back without interruption. If a track fades out (ends with the sound gradually decreasing), the fadeout portion will also be skipped.

To return to normal playback

Press CD BLANK SKIP again. “CD BLANK SKIP OFF” is displayed and the dot in the display will disappear,

● There may be a case where BLANK SKIP PLAY does not

function correctly.

● BLANK SKIP PLAY is automatically canceled when performing

Al EDIT RECORDING (page 16), PROGRAMMED EDIT

RECORDING (page 17), or recording during PROGRAMMED PLAY (page 14) or RANDOM PLAY (page 13).

● When you press CD BLANK SKIP to turn on/off the flash

window, the BLANK SKIP PLAY is also switched to ON/OFF.

REPEAT play

A single disc or all the discs can be played repeatedly.

Press RANDOM/REPEAT while pressing SHIFT.

Each time it is pressed, the function can be selected cyclically.

RANDOM piay — RANDOM lights upon the display.

REPEAT play — ~ lights up on the display.

RANDOM/REPEAT play —

display.

RANDOM and ~ light upon the

Cancel — RANDOM and CE disappear from the display.

To play all discs, press E to start play.

To play a single disc, press one of DISC DIRECT PLAY 1-5 to start play. Toselect disc 4 or 5 from the remote control, press DISC DIRECT

PLAY 4 or 5 while pressing

SHIFT.

Durin[g random play it is not possible to skip to the previously played track with 44.

ENGLISH 13

To check the program

Each time + or - is pressed in stop mode, a disc number, track number, and program number will be displayed.

Up to 30 tracks can be programmed from any of the inserted discs.

Use the remote control.

Press PRGM while pressing SHIFT in stop mode.

is displayed

“--”

Press one of DISC DIRECT PLAY 1-5 to select a

disc.

To select disc 4 or 5, press DISC DIRECT PLAY 4 or 5 while

pressing SHIFT. Go to the next step when the tray stops rotating.

Press numbered buttons O-9 and +1Oto program

a track.

Example: To select the 25th track, press +1O,+1Oand 5. To select the 10th track, press +1Oand O.

Selected track number

Total number of selected tracks

To clear the program

Press

■CLEAR in stop mode.

To add tracks to the program

Repeat steps 2 and 3 instop mode. The track will be programmed after the last track.

To change the programmed tracks

Clear the program and repeat all the steps again.

To play the programmed tracks repeatedly

After programming the tracks, press RANDOM/REPEAT repeatedly while pressing SHIFT until CL appears on the display.

● During programmed play, you can not use random play, check

the remaining time or select a track.

● “FULL” is displayed if you attempt to program more than 30

tracks.

Program number

Repeat steps 2 and 3 to program other tracks.

5 Press -to start play.

Total playing time of the selected tracks

14 ENGLISH

Preparation

● Use Type I (normal) tapes only.

oSet the tape to the point where recording will start. * Note that recording is

done on only one side of the tape.

To record part of the CD

When ● is pressed, recording always starts from the first track.

Tostart in the middle of a track, play the CD first and press 1I SET

CD at the point you wish to start recording from. Then, press

for

..-rhe pause mode for CD button is released automatically and recc)rding starts.

Sound adjustment during recording

The output volume and tone of the speakers or headphones are freely varied without affecting the recording.

● Dc)not press the buttons on Deck 2 during recording.

● ● cannot be depressed if the erasure prevention tab on the

side of the tape to be recorded is broken off.

erase a recording

A previous recording is erased when a new recording is made on that part of that tape.

1 Insert the tape you want to erase into Deck 1.

2 F)ress TAPE and stop all the tape operation in Deck 2.

3 Windup the tape to the point where the erasure is to be started. 4 F’ress

● on Deck 1 to start the erasure.

7 Insert the tape to be recorded on into Deck 1.

Insertthetapewiththesidetobe

from the unit.

recorded on first facing out

Press one of the function buttons and prepare

...............

the source to be recorded.

record from a CD, press CD and load the disc(s).

~record from a tage, press TAPE. Then, insert the original tape into Deck 2 and play it. To record from a radio broadcast, press TUNER/BAND and tune into a station. To record from a connected source, press PHONO or VIDEO/AUX and play.

Press ● cm Deck 1 to start recording.

> is depressed simultaneously. When the selected function is CD, playback and recording start simultaneously.

I ! !

About cassette tapes

● To prevent accidental erasure, break off the plastic tabs

on the cassette tape after recording with a screwdriver or other pointed tool.

Side A

To stop recording, press To pause recording, press II on Deck 1. ‘To resume recording, press it again.

To record selected tracks of the CD

Before pressing ●, program the tracks (page 14).

■/A on Deck 1.

To record on the tape again, cover the tab openings with adhesive tape, etc.

● “120-minute or longer tapes are extremely thin and easily

deformed or damaged. They are not recommended.

● Take up any slack in the tape with a pencil or similar tool

before use. Slack tape may break or jam in the mechanism.

ENGLISH ~ ~

—nisc

The Al edit recording function enables CD recording without

worrying about tape length and track length. When a CD is

inserted, the unit automatically calculates the total track length. if necessary, the order of tracks is rearranged so that no track is cut short. (Al: Artificial Intelligence)

Insert the tape into Deck 1.

Insert the tape with the side to be recorded on first facing out

from the unit, and wind up the tape with -.

Press ● on Deck 1 to start recording on the first side.

flashes for 10 seconds, and then CD play and recording

of edited tracks for the first side start simultaneously. When

the end of the tape is reached, Deck 1 enters the recording

stop mode. After entering the recording stop mode go to step

Press CD EDIT/CHECK while pressing SHIFT on

the remote control to display the program for the

second recording.

“B” is displayed.

Turn over the tape in Deck 1 and press ● to start

recording on the second side. -

To stop recording

Press WA on Deck 1. Recording and CD play stop simultaneously.

To clear the edit program

■CLEAR twice in the stop mode so that “EDIT disappears

Press

on the display, or press AOPEN/CLOSE.

To check the order of the programmed track numbers

Before recording, press CD EDIT/CHECK while pressing SHIFT on the remote control to select side A or B, and press < or

- repeatedly or turn MULTI JOG. Track number

Programmed track numbers

Press CD and load the disc(s).

Press CD EDIT/CHECK once while pressing

SHIFT on the remote control.

“Al EDIT” is displayed.

Al EDIT

● When “PRGM” is displayed, press CD EDIT/CHECK while

pressing SHIFT again.

Press one of DISC DIRECT PLAY 1-5 to select a

disc.

To select disc 4 or 5 from the remote control, press DISC DIRECT PLAY 4 or 5 while pressing SHIFT.

Press numbered buttons O-9 on the remote

control to designate the tape length.

10 to 99 minutes can be specified. Example: When using a 60-minute tape, press 6 and O. In a few seconds, the tracks to be recorded on each side of the tape are determined,

● 4, - or MULTI JOG are also available to designate

the tape length.

Tape length

Remaining time Programmed of recording

tracks for side A

Tape side

Program number

To add tracks from other discs to the edit program

If there is any time remaining on the tape after step 5, you can add tracks from other discs in the CD compartment. 1 Press CD EDIT/CHECK while pressing SHIFT on the

control to select side A or B.

Press one of DISC DIRECT PLAY 1-5 to select a disc. To select disc 4 or 5 from the remote control, press DISC DIRECT PLAY 4 or 5 while pressing SHIFT.

3 Press numbered buttons on the remote control to select

tracks. A track whose playing time is longer than the remaining time cannot be programmed.

4 Repeat steps 2 and 3 to add more tracks.

Time on cassette tapes and editing time

The actual cassette recording time is usually a little longer than the specified recording time printed on the label. This unit can program tracks to use the extra time. When the total recording time is a little longer than the tape’s specified recording time after editing, the display shows the extra time (without a minus mark), instead of the time remaining on the tape (with the minus mark).

The Al edit recording function cannot be used with discs containing 31 tracks or more. “TR OVER” is displayed if this is attempted.

remote

16 ENGLISH

I Minus mark Tape side A: First recording side B: Second recording side

In the programmed edit recording function the tracks can be programmed while checking the remaining time on each side of the tape as the tracks are programmed.

Insert the tape into Deck 1.

Insert the tape with the side to be recorded on first facing out

from the unit, and wind

Press CD and load the disc(s).

Press CD EDIT/CHECK twice while pressing

up the tape with <.

SHIFT on the remote control.

“EDIT” and “PRGM” are displayed.

PRGM

EDIT

Repeat step 5 for the rest of the tracks for side

A track whose playing time is longer than the remaining time

cannot be programmed.

Press CD EDIT/CHECK while pressing SHIFT on

the remote control to select side B and program the tracks for side B.

Tape side B (reverse side)

Press CD EDIT/CHECK while pressing SHIFT to

select side A and press

flashes for 10 seconds, and then CD play and recording

of edited tracks for the first side start simultaneously. When

the end of the tape is reached, Deck 1 enters the recording

stop mode. After entering the recording stop mode, go to step 9.

Press CD EDIT/CHECK while pressing SHIFT on

● on Deck 1.

the remote control for recording of the second

side.

“B” is displayed.

10 Turn over the tape in Deck 1 and press @to start

recording.

Recording starts.

To stop recording

Press simultaneously.

■/A on Deck 1. Recording and CD play stop

● When “AI” is displayed, press CD EDIT/CHECK while

pressing SHIFT again.

Press numbered buttons on the remote control

to designate the tape length.

10 to 99 minutes can be specified. . <M, - or MULTI JOG are also available to designate

the tape length.

Tape length

Tape side A (front side)

Maximum recording time for side A

5 Press one of DISC DIRECT PLAY 1-5 to select a

disc. Then, press numbered buttons O-9 and +10 on the remote control to program a track.

To select disc 4 or 5 from the remote control, press DISC

DIRECT PLAY 4 or 5 while pressing SHIFT. Example: To select the 10th track of disc 2, press DISC DIRECT PLAY 2, then press +10 and O.

Programmed

Selected track number

Remaining

time on side A track numbers

To check the order of the programmed track numbers

Before recording, press CD EDIT/CHECK while pressing SHIFT

on the remote control to select side A or B, and press < or

M- repeatedly.

Track number

Disc ~umber Progra’m number

change the program of each side

Press CD EDIT/CHECK while pressing SHIFT on the remote

control to select side A or B, and press program on the selected side. Then program tracks again.

To clear the edit program

■CLEAR twice in stop mode so that “EDIT” disappears

Press

on Ithe display.

Programmed track numbers

■CLEAR to clear the

● Recording is inhibited if the erasure prevention tab for the side

of the tape facing out from the unit is broken off.

s Up to 30 tracks can be programmed from any of the inserted

discs.

. “FULL” is displayed if you attempt to program more than 30

tracks.

Prog;am number

ENGLISH I 7

When the clock is set, the flashes. When the clock setting is canceled due to a power failure, the entire clock display flashes.

“:” between the hours and minutes

The unit can be turned off automatically at a specified time,

Use the remote control.

7 Press II.

When using the remote control, press CLOCK while pressing

SHIFT.

2 Within 4 seconds, turn MULTI JOG to designate

the hour and the minute.

Turning MULTI JOG changes both the hour and the minute.

- or > is also available instead of MULTI JOG. Holding

these buttons down will vary the time rapidly.

3 Press ENTER or 11.

The clock starts from 00 seconds.

To view the clock when another display is in the display

Press CLOCK while pressing SHIFT. The time isdisplayed for 4 seconds and then the original display reappears. However, the clock cannot be displayed during recording.

To switch to the 24-hour standard

Press IIII and then press

Repeat the same procedure to restore the 12-hour standard.

If the clock display flashes

If the display flashes when the clock is displayed, it indicates that the clock has stopped due to a power failure or the removal of the Dower cord. The current time needs to be reset.

■ within 4 seconds.

1 Press SLEEP while pressing SHIFT on the remote

control.

2 Within 4 seconds, turn MULTI JOG or press ++

or + to specify the time until the power is turned off.

The time changes between 5 and 240 minutes in 5-minute steps.

Specified time

To check the time remaining until the power is turned off

Press SLEEP once while pressing SHIFT. The remaining time is

displayed for 4 seconds.

To cancel the sleep timer

Press SLEEP twice while pressing SHIFT so that “SLEEPOFF”

appears on the display.

If the power-economizing mode (page 7) is on, all the display

lights turn off when the power is turned off. To view the clock,

press II so that the time is displayed for 4 seconds.

18 ENGLISH

The unit can be turned on at a specified time every day with the built-in timer.

Preparation

Make sure the clock is set correctly.

Press one of the function buttons to select a

,—,/

–(

source.

● If TUNER/BAND is pressed, the band cannot be selected in

this step.

Press TIMER to display @l and (! PLAY.

When using the remote control, press TIMER while pressing

SHIFT. Time and audio

source name flash alternately.

Adjust the volume.

The source sound will play at the volume level set in this step

when the power is turned on by the timer.

If the volume level is set to 21 or higher, however, it will :;~’ automatically be set to 20 when the power is turned on,

Prepare the source.

To listen to a CD, load the disc to be played first on tray 1. To listen to a tape, insert the tape into deck 1 or 2. To listen to the radio, tune in to a station.

Press POWER to turn off the power.

remains on the display after the power is turned off (timer

standby mode) if the power-economizing mode is OFF.

Get ready for the TAPE function or the timer

recording.

To listen to the tape, press > on Deck 1 or 2. To record the source,

O on Deck 1.

VVhen the timer-on time is reached, the unit turns on and

begins play with the selected source.

insert the tape into Deck 1 and press

● You can change the source that was selected in step 1 by

pressing one of the function buttons before pressing

or II in ster33.

● If the power-economizing mode is ON, @ is not displayed in

thf?timer standby mode.

The timer recording period and tape length

Wh[?n the length of the tape to be recorded is shorter than the timer recording period, is off. Wh[?n the tape length is longer than the timer recording period,

● on deck 1 is released before the timer

● is not released. If ● is not released for a long time, the tape

in the deck may be damaged. Press WA to release

ENTER

●.

:~;

:,$j

.,, :,,.

!:&

~ o

❑

~thin 6 seconds, turn MULTI JOG to designate

the timer-on time, then press ENTER or 11.

Turning MULTI JOG changes both the hour and the minute.

~< or - is also available instead of MULTI JOG. Holding

these buttons down will vary the time rapidly.

4 ~thin 4 seconds, turn MULTI JOG to select

duration for the timer-activated period.

The duration can be set between 5 and 240 minutes in 5mirrute steps.

● - or - is also available instead of MULTI JOG.

The duration will be automatically set after 4 seconds. It will also be set if ENTER or II is pressed within 4 seconds after Stc?p4.

the

/ENGL/SH19

To check the timer setting

Press TIMER. The selected source, the timer-on time, and the duration for the timer-activated period will be displayed for 4 seconds.

To change any of the previous setting Carry out from step 1.

However, if you do not change the timer-on time, in step 3 just press ENTER twice and continue from step 4.

(\.-–-—– .– ‘i

To cancel the timer standby mode temporarily

Press TIMER so that 0 disappears. To restore the timer standby mode, press TIMER again to display

Using the unit while the timer is set

You can use the unit normally after setting the timer.

Before turning off the power, carry out step 5 and 6.

● Timer playback and timer recording will not begin unless the

power is turned off.

● Connected equipment cannot be turned on and off by the built-

in timer of this unit. Use an external timer.

2,4

Preparation

● Connect the supplied stereo turntable to the

page 4)

● Set EQUALIZER AMP. selector on the turntable to ON position.

(Refer to the operating instructions of the turntable for details.)

Press PHONO on the main unit.

“PHONO” appears on the display.

Adjust the volume to minimum.

Turn VOLUME counterclockwise until “VOL O“ is displayed.

Play the turntable.

Refer to the operating instructions of the turntable for details.

Adjust the volume according to your preference.

main unit. (See

20 ENGLISH

OTHER CONNECTIONS

Iaaiaa

Refer to the operating instructions of the connected equipment for details. “ The connecting cords are not supplied. Obtain the necessary

connecting cords.

● Consult your local Aiwa dealer for optional equipment.

Sml

CD DIGITAL OUT

(OPTICAL)

VIDEO/AUX

Vli3E0/AllIX IN JACKS

This unit can input analog sound signals through these jacks. Use a cable with RCA phono plugs to connect audio equipment (LD players, MD players, VCRs, TV, etc.). Connect the red plug to VIDEO/AUX IN R jack, and the white plug to V!DEO/AUX IN L jack.

To Iplayequipment connected to VIDEO/AUX IN jacks proceed & as follows.

7 lPress

VIDEO/AUX.

“VIDEO” appears on the display.

2 lPlay the connected equipment.

To change a source name on the display When VIDEO/AUX is pressed, “VIDEO” is displayed initially. It canl be changed to “AUX” or ‘(TV. With the power on, press POWER while pressing VIDEO/AUX.

Repeat the procedure to select one of the names.

w z

CDI ~[G[TAL OUT (OPTICAL) JACK

This unit can output CD digital sound signals through this jack. Use an optical cable to connect digital audio equipment (DAT

deck, MD recorder, etc.).

Remove the dust cap @ from the CD DIGITAL OUT (OPTICAL) jack. Then, connect an optical cable plug to the CD DIGITAL OUT (OPTICAL) jack.

(’a

When the CD DIGITAL OUT (OPTICAL) jack is not being usedl

Attach the supplied dust cap.

❑

ENGLISH 21

+ 47 hidden pages