Sony WEGA KV-FA29 Operating Instructions Manual

2-898-277-11 (1)

Tr initron Color TV

Operating Instructions

• Before operating the unit, please read this manual thoroughly and retain it for future reference.

KV-FA29

M83 M53

WARNING

• Dangerously high voltages are present inside the TV.

• TV operating voltage: 110 – 240 V AC.

• Do not plug in the power cord until you have completed making all other connections; otherwise a minimum leakage current might flow through the antenna and other terminals to ground.

•To avoid battery leakage and damage to the remote, remove the batteries from the remote if you are not going to use it for several days. If any liquid leaks from the batteries and touches your skin, immediately wash it away with water.

For your own safety, do not touch any part of the TV, the power cord and the antenna cable during lightning storms.

Do not place any objects on the TV. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

Do not block the ventilation openings of the TV. Do not install the TV in a confined space, such as a bookcase or built-in cabinet.

Do not open the cabinet and the rear cover of the TV as high voltages and other hazards are present inside the TV. Refer servicing and disposal of the TV to qualified personnel.

For children’s safety, do not leave children alone with the TV. Do not allow children to climb onto it.

Do not operate the TV if any liquid or solid object falls into it. Have it checked immediately by qualified personnel only.

Your TV is recommended for home use only. Do not use the TV in any vehicle or where it may be subject to excessive dust, heat, moisture or vibrations.

Clean the TV with a dry and soft cloth. Do not use benzine, thinner, or any other chemicals to clean the TV. Do not attach anything (e.g., adhesive tape, cellophane tape, glue) on the painted cabinet of the TV. Do not scratch the picture tube.

To prevent fire or shock hazard, do not expose the TV to rain or moisture.

Install the TV on a stable TV stand and floor which can support the TV set weight. Ensure that the TV stand surface is flat and its area is larger than the bottom area of the TV.

Do not plug in too many appliances to the same power socket. Do not damage the power cord.

Pull the power cord out by the plug. Do not pull the power cord itself. Even if your TV is turned off, it is still connected to the AC power source (mains) as long as the power cord is plugged in. Unplug the TV before moving it or if you are not going to use it for several days.

Table of Contents

Installation

Securing the TV .................................... 4

Getting Started ..................................... 5

Setting up your TV

(“Initial Setup”) .................................... 6

Overview of Controls

TV front and rear panels ..................... 8

Using the remote control and

basic functions ...................................... 9

Advanced Operations

Selecting the picture and sound

modes .................................................. 11

Menu Adjustment

Introducing the WEGA GATE

navigator ............................................. 12

“Settings” Adjustment ...................... 13

Changing the “Picture” setting ........ 14

Changing the “Sound” setting ......... 16

Changing the “Channel Setup”

setting .................................................. 17

Changing the “Setup” setting .......... 19

Additional Information

Connecting the 3D WOOFER, TWEETER and CENTER

SPEAKER ............................................ 20

Connecting optional components ... 21

Troubleshooting ................................. 23

Specifications ...................... Back cover

Installation

x Securing the TV

To prevent the TV from falling, use the supplied screws, clamps and band to secure the TV.

20 mm

3.8 mm

screws clamps band

Screw the band to the TV stand and to the provided hole at the rear of your TV.

(1) Put a cord or chain through the clamps. (2) Screw one clamp to a wall or pillar and

the other clamp to the provided hole at the rear of your TV.

(1) Attach each end of a cord or chain to

the provided holders at the rear of your TV.

(2) Securely fix the attached cord or chain

to a wall or pillar using an attachment which can support the TV set weight.

Note

• Use only the supplied screws. Use of other screws may damage the TV.

4 Installation

x Getting Started

Step 1

Insert the batteries (supplied) into the remote.

Note

• Do not use old or different types of batteries together.

Step 2

Connect the antenna cable (not supplied) to 8 (antenna input) at the rear of the TV.

Tip

•You can also connect your TV to other optional components (see page 21).

Step 3

Installation

Select

Confirm

Plug in the power cord, then press ! on the TV to turn it on.

Note

• The 1 (standby) indicator flashes green for a few seconds when turning on the TV. This does not indicate a malfunction.

Step 4

Set up the TV by following the instructions of the “Initial Setup” menu (see page 6).

End

Installation

Setting up your TV

(“Initial Setup”)

When you turn on your TV for the first time, the “Initial Setup” menu will appear. You may change the menu language, preset the TV channels automatically, sort or edit the channels and adjust the picture position using the buttons on the remote control or TV front panel.

Press V or v to select the desired menu

language, then press .

The selected menu language appears.

Select

Press V or v to select “Yes”, then press

to preset the channels automatically.

The screen will indicate automatic presetting is in progress.

After all available channels have been tuned and stored, the “Program Sorting/Edit” menu appears automatically on the screen.

Select

Program:

TV System: B/G VHF Low

Confirm

End

To skip automatic channel presetting, select “No”, then press

If the message “No channel found. Please connect cable/antenna” appears, check your TV connections, then press

The “Program Sorting/Edit” menu enables

you to sort and edit the channels.

a) If you wish to keep the channels in the current

condition, press WEGA GATE to exit.

b) Press V or v to select the program

number with the channel you wish to change. The selected channel will appear on the screen.

c) If you wish to store the channels in a

different order:

1) Press b to enter sorting mode.

2) Press V or v to select the new program

6 Installation

number position for your selected channel, then press B.

Program Sorting/Edit

PROG

Sorting:

Select

Program Sorting/Edit

PROG

Sorting mode

Select

SkipLabel

Off

Edit:

Confirm

SkipLabel

Off

Confirm

End

Exit

Off01

Exit

d) If you wish to edit the channels, press

to change to edit mode. Press b until the mode that you wish to edit is highlighted: Label, Skip, (block symbol). Then press

1) To label, press V or v to select the alphanumeric characters for the label. Then press

2) To skip the program number, press V or v to select “On”. Then press

You can skip this program number when using PROG +/-.

3) To block unwanted program number, press V or v to select

. Then press .

e) Repeat step b) to d) if you wish to change other

channels.

Press WEGA GATE to exit.

Press B or b to adjust the bars on the top

and bottom of the menu if they are slanted, then press

“Picture V-Position” menu appears.

Select

Confirm

Exit

Installation

Exit

End

If the upper and lower bars are not

equally positioned to the top and bottom of the screen, press V or v to adjust them, then press

Select

End

Confirm

If no adjustment is necessary, then press .

To prevent this “Initial Setup” menu from

appearing again when you turn on the TV by pressing !, press V or v to select “No”, then press

To allow this menu to appear again, select “Yes”, then press

Tip

•You can immediately go to the end of the ”Initial Setup” menu by pressing WEGA GATE.

Select

Confirm

Installation

Overview of Controls

x TV front and rear panels

TV rear panel

(MONO) (MONO)

M I C 1

M I C 2

L ( M O N O )

F M

P R O G

qj qgqh qf

qa qd qs qa

TV front panel

L(MONO) R

SOUND

MODE

WEGA GATE

678

PROG

Button/Terminal Function Page

1 ! Turn off or turn on the TV. 5 2 Wake Up indicator. 10 2 1 Standby indicator. 5 3 Remote control sensor. – 4 PROG +/– Select program number. – 5 2 +/– Adjust volume. – 6 t Select TV or video input. 21

WEGA GATE menu operations

4,5

, , ,

Select and adjust items. 12

6 Confirm selected items. 12 7 WEGA GATE Display or cancel WEGA GATE menu. 12

8 SOUND MODE Select sound mode options with a 5-Band Graphic 11

Equalizer display.

9 i Headphone jack. – 0 t2Video input terminal 2. 21 qa TWEETER TWEETER terminal. 20 qs CENTER SPEAKER Center speaker input terminal. 20 qd WOOFER 3D WOOFER terminal. 20 qf 8 Antenna input terminal. 21 qg T Monitor output terminal. 21 qh Component video input terminal. 22 qj t1Video input terminal 1. 21

8 Overview of Controls

+ 17 hidden pages

Sony WEGA KV-FA29 Operating Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual