Sony WEGA KV-BZ212 Operating Instructions Manual

2-677-500-11 (1)

Trinitron Color TV

Operating Instructions

• Before operating the unit, please read this manual thoroughly and retain
it for future reference.

GB

KV-BZ212

© 2006 Sony Corporation

M80

A Specifications

KV-BZ212M80

Power requirements

Power consumption (W)

Television system

Color system

Channel coverage

B/G

I

D/K

8 (Antenna)

Audio output (Speaker)

Number of terminal

(Video)

(Audio)

Picture tube

Tube size (cm)

Screen size (cm)

Dimensions (w/h/d, mm)

Mass (kg)

Design and specifications are subject to change without notice.

110-240 V AC, 50/60 Hz

Indicated on the rear of the TV

B/G, I, D/K

PAL, PAL 60, SECAM, NTSC3.58 (AV IN), NTSC4.43

VHF : E2 to E12 /UHF : E21 to E69 /
CATV : S01 to S03, S1 to S41

UHF : B21 to B68 /CATV : S01 to S03, S1 to S41

VHF : C1 to C12, R1 to R12 /
UHF : C13 to C57, R21 to R60 /
CATV : S01 to S03, S1 to S41, Z1 to Z39

75-ohm external terminal

3 W + 3 W

Input: 2 Phono jacks; 1 Vp-p, 75 ohms

Input: 2 Phono jacks; 500 mVrms

21 in.

54

51

497 × 468 × 494

23

Note

Measured diagonally

Measured diagonally

B WARNING

• Dangerously high voltages are present inside the TV.

• TV operating voltage: 110 – 240 V AC.

• Do not plug in the power cord until you have completed making all other
connections; otherwise a minimum leakage current might flow through the antenna
and other terminals to ground.

• To avoid battery leakage and damage to the remote, remove the batteries from the
remote if you are not going to use it for several days. If any liquid leaks from the
batteries and touches your skin, immediately wash it away with water.

For your own safety, do not touch
any part of the TV, the power cord
and the antenna cable during
lightning storms.

Do not place any objects on the TV.
The apparatus shall not be
exposed to dripping or splashing
and that no objects filled with
liquids, such as vases, shall be
placed on the apparatus.

Do not block the ventilation
openings of the TV. Do not install
the TV in a confined space, such
as a bookcase or built-in cabinet.

Do not open the cabinet and the
rear cover of the TV as high
voltages and other hazards are
present inside the TV. Refer
servicing and disposal of the TV
to qualified personnel.

For children’s safety, do not leave
children alone with the TV. Do not
allow children to climb onto it.

Do not operate the TV if any liquid
or solid object falls into it. Have it
checked immediately by qualified
personnel only.

Your TV is recommended for
home use only. Do not use the TV
in any vehicle or where it may be
subject to excessive dust, heat,
moisture or vibrations.

Clean the TV with a dry and soft
cloth. Do not use benzine, thinner,
or any other chemicals to clean the
TV. Do not attach anything (e.g.,
adhesive tape, cellophane tape,
glue) on the painted cabinet of the
TV. Do not scratch the picture
tube.

To prevent fire or shock hazard, do
not expose the TV to rain or
moisture.

Install the TV on a stable TV stand
and floor which can support the
TV set weight. Ensure that the TV
stand surface is flat and its area is
larger than the bottom area of the
TV.

Do not plug in too many
appliances to the same power
socket. Do not damage the power
cord.

Pull the power cord out by the
plug. Do not pull the power cord
itself. Even if your TV is turned
off, it is still connected to the AC
power source (mains) as long as
the power cord is plugged in.
Unplug the TV before moving it
or if you are not going to use it for
several days.

C Securing the TV

To prevent the TV from falling, use the supplied screws, clamps and band to

secure the TV. Use only the supplied screws. Use of other screws may damage
the TV.

20 mm

screws

3.8 mm
clamps band

or

Screw the band to the TV stand and
to the provided hole at the rear of
your TV.

(1) Put a cord or chain through the

clamps.

(2)

Screw one clamp to a wall or pillar
and the other clamp to the provided
hole at the rear of your TV.

D Getting Started

Step 1

b

Insert the batteries (supplied) into the remote.

Note

•Do not use old or different types of batteries together.

Step 2

Connect the antenna cable (not supplied) to 8
(antenna input) at the rear of the TV.

Tip

•You can also connect your TV to other optional components (see G).

Step 3

b

Plug in the power cord, then press ! on the TV to turn it on.

Note

•The 1 (standby) indicator flashes green for a few seconds when

turning on the TV. This does not indicate a malfunction.

Step 4

Set up the TV by following the instructions of the “Initial
Setup” menu (see E).

End

Confirm

Select

Program Sorting/Edit

01
02

03

04

Off

Off

Off

Sorting mode

PROG

SkipLabel

Off01

Exit

Select

Confirm

Program Sorting/Edit

01
02
03
04

Off
Off
Off
Off

Sorting:

Edit:

PROG

SkipLabel

Exit

Select

Confirm

End

Select

Confirm

End

Select

Confirm

Start auto program now?

Program:

TV System: B/G

01

VHF Low

End

E

Setting up your TV (“Initial Setup”)

When you turn on your TV for the first time, the “Initial Setup” menu will
appear. You may change the menu language, preset the TV channels
automatically and sort or edit the channels using the buttons on the remote
control or TV top control panel.

Press V or v to select the desired menu

1

language, then press .

The selected menu language appears.

Press V or v to select “Yes”, then press to

2

preset the channels automatically.

The screen will indicate automatic
presetting is in progress.

After all available channels have been tuned
and stored, the “Program Sorting/Edit”
menu appears automatically on the screen.

To skip automatic channel presetting, select
“No”, then press

.

If the message “No channel found. Please
connect cable/antenna” appears, check your
TV connections, then press

.

The “Program Sorting/Edit” menu enables

3

you to sort and edit the channels.

a) If you wish to keep the channels in the current

b) Press V or v to select the program

c) If you wish to store the channels in a

condition, press WEGA GATE to exit.

number with the channel you wish to
change. The selected channel will appear
on the screen.

different order:

1) Press b to enter sorting mode.

2) Press V or v to select the new program
number position for your selected
channel, then press B.

Setting up your TV (“Initial Setup”) (continued)

d) If you wish to edit the channels, press

to change to edit mode.
Press b until the mode that you wish to edit
is highlighted: Label, Skip,
Then press

.

1) To label, press V or v to select the
alphanumeric characters for the label.
Then press

.

2) To skip the program number, press V or v to
select “On”. Then press

You can skip this program number when
using PROG +/-.

3) To block unwanted program number,
press V or v to select

(block symbol).

.

. Then press .

Select

Select

Confirm

Confirm

Exit

Exit

e) Repeat step b) to d) if you wish to change other

channels.

Select

Confirm

Press WEGA GATE to go to the next menu.

To prevent this “Initial Setup” menu from

4

appearing again when you turn on the TV
by pressing !, press V or v to select “No”,
then press

To allow this menu to appear again, select
“Yes”, then press

Tip

• You can immediately go to the end of the ”Initial Setup” menu by pressing WEGA GATE.

.

Select

Confirm

.

Exit