Sony Wega KV-BZ14, Wega KV-BZ21 Operating Instructions Manual

2-638-467-12 (1)

Tr initron Color TV

Operating Instructions

• Before operating the unit, please read this manual thoroughly and retain
it for future reference.

使用說明書

• 使用本電視機之前請先詳細閱讀此手冊﹐並妥善保存以備日後用作參考。

GB

CT

KV-BZ21
KV-BZ14

© 2005 Sony Corporation

M50
M40

P40

WARNING

• Dangerously high voltages are present inside the TV.

• TV operating voltage: 110 – 240 V AC.

• Do not plug in the power cord until you have completed making all other
connections; otherwise a minimum leakage current might flow through the antenna
and other terminals to ground.

•To avoid battery leakage and damage to the remote, remove the batteries from the
remote if you are not going to use it for several days. If any liquid leaks from the
batteries and touches your skin, immediately wash it away with water.

For your own safety, do not touch
any part of the TV, the power cord
and the antenna cable during
lightning storms.

Do not place any objects on the TV.
The apparatus shall not be
exposed to dripping or splashing
and that no objects filled with
liquids, such as vases, shall be
placed on the apparatus.

Do not block the ventilation
openings of the TV. Do not install
the TV in a confined space, such
as a bookcase or built-in cabinet.

Do not open the cabinet and the
rear cover of the TV as high
voltages and other hazards are
present inside the TV. Refer
servicing and disposal of the TV
to qualified personnel.

For children’s safety, do not leave
children alone with the TV. Do not
allow children to climb onto it.

Do not operate the TV if any liquid
or solid object falls into it. Have it
checked immediately by qualified
personnel only.

Your TV is recommended for
home use only. Do not use the TV
in any vehicle or where it may be
subject to excessive dust, heat,
moisture or vibrations.

Clean the TV with a dry and soft
cloth. Do not use benzine, thinner,
or any other chemicals to clean the
TV. Do not attach anything (e.g.,
adhesive tape, cellophane tape,
glue) on the painted cabinet of the
TV. Do not scratch the picture tube.

To prevent fire or shock hazard, do
not expose the TV to rain or
moisture.

Install the TV on a stable TV stand
and floor which can support the
TV set weight. Ensure that the TV
stand surface is flat and its area is
larger than the bottom area of the
TV.

Do not plug in too many
appliances to the same power
socket. Do not damage the power
cord.

Pull the power cord out by the
plug. Do not pull the power cord
itself. Even if your TV is turned off,
it is still connected to the AC power
source (mains) as long as the power
cord is plugged in. Unplug the TV
before moving it or if you are not
going to use it for several days.

2

Table of Contents

Getting Started ............................................................................................................... 4

Setting up your TV (“Initial Setup”) ........................................................................... 5

TV top control, front and rear panels ......................................................................... 7

Connecting optional components ............................................................................... 8

Using the remote control and basic functions ......................................................... 10

Introducing the WEGA GATE navigator ................................................................. 12

“Settings” Adjustment ................................................................................................ 13

Changing the “Picture” setting .................................................................................. 14

Changing the “Sound” setting ................................................................................... 15

Changing the “Channel Setup” setting .................................................................... 16

Changing the “Setup” setting .................................................................................... 18

Troubleshooting ........................................................................................................... 19

Specifications ................................................................................................ Back cover

GB

3

x Getting Started

Step 1

b

b

Insert the batteries (supplied) into the remote.

Note

• Do not use old or different types of batteries together.

Step 2

Connect the antenna cable (not supplied) to 8
(antenna input) at the rear of the TV.

Tip

•You can also connect your TV to other optional components
(see page 8).

Step 3

Plug in the power cord, then press ! on the TV to
turn it on.

Note

• The 1 (standby) indicator flashes green for a few seconds
when turning on the TV. This does not indicate a malfunction.

Step 4

Set up the TV by following the instructions of the
“Initial Setup” menu (see page 5).

Select

Confirm

End

4

x S

Start auto program now?

End

Select

Confirm

Start auto program now?

Program:

Auto Program

TV System: Auto

01

VHF Low

End

Program Sorting/Edit

01
02

03

04

Off

Off

Off

Sorting mode

PROG

SkipLabel

Off01

Exit

Select

Confirm

Program Sorting/Edit

01
02
03
04

Off
Off
Off
Off

Sorting:

Edit:

PROG

SkipLabel

Exit

Select

Confirm

etting up your TV (“Initial Setup”)

When you turn on your TV for the first time, the “Initial Setup” menu will
appear. You may change the menu language, preset the TV channels
automatically and sort or edit the channels using the buttons on the remote
control or TV top control panel.

Press V or v to select the desired menu

1

language, then press .

The selected menu language appears.

Press V or v to select “Yes”, then press to

2

preset the channels automatically.

The screen will indicate automatic
presetting is in progress (“TV system” is
available for KV-BZ21M50/BZ21M40/
BZ14M40 only).

After all available channels have been tuned
and stored, the “Program Sorting/Edit”
menu appears automatically on the screen.

To skip automatic channel presetting, select
“No”, then press

.

If the message “No channel found. Please
connect cable/antenna” appears, check your
TV connections, then press

.

Select

Confirm

End

The “Program Sorting/Edit” menu enables

3

you to sort and edit the channels.

a) If you wish to keep the channels in the current

b) Press V or v to select the program

c) If you wish to store the channels in a

condition, press WEGA GATE to exit.

number with the channel you wish to
change. The selected channel will appear
on the screen.

different order:

1) Press b to enter sorting mode.

2) Press V or v to select the new program
number position for your selected
channel, then press B.

continue

5

Setting up your TV (“Initial Setup”) (continued)

Select

Confirm

d) If you wish to edit the channels, press

to change to edit mode.
Press b until the mode that you wish to edit
is highlighted: Label, Skip, (block symbol).
Then press

1) To label, press V or v to select the
alphanumeric characters for the label.
Then press

2) To skip the program number, press V or v to
select “On”. Then press

You can skip this program number when
using PROG +/-.

3) To block unwanted program number,
press V or v to select

.

.

.

. Then press .

Select

Select

Confirm

Confirm

Exit

Exit

e) Repeat step b) to d) if you wish to change other

channels.

Select

Confirm

Press WEGA GATE to go to the next menu.

To prevent this “Initial Setup” menu from

4

appearing again when you turn on the TV
by pressing !, press V or v to select “No”,
then press

.

To allow this menu to appear again, select
“Yes”, then press

Tip

•You can immediately go to the end of the “Initial Setup” menu by pressing WEGA GATE.

.

Exit

6

x TV top control, front and rear panels

TV top control panel

WEGA GATE

SOUND MODE

0

9

8

7

TV rear panel

KV-BZ21M50

1

Y

C

TV front

(MONO) (MONO)

L

R

qf

qd

B

L

C

R

R

qa

qs

panel

KV-BZ21M50

L

(MONO)

5

2

R

4

23

KV-BZ21M40/BZ21P40/BZ14M40/BZ14P40

2

(MONO) (MONO)

1

5

Button/Terminal Function Page

1 ! Turn off or turn on the TV. 4
2 Remote control sensor. -
3 Wake Up indicator. 11
3 1 Standby indicator. 4
4 i Headphone jack. -
5 t2Video input terminal 2. 8
6 PROG +/– Select program number. -
7 2 +/– Adjust volume. -
8 t Select TV or video input. 8

WEGA GATE menu operations

6,7 V,v,B,b Select and adjust items. 12

Confirm selected items. 12

8
9 WEGA GATE Display or cancel WEGA GATE menu. 12

0 SOUND MODE Select sound mode options with a 5-Band Graphic 10

(KV-BZ21M50 only) Equalizer display.

qa 8 Antenna input terminal. 8
qs T Monitor output terminal. 8
qd Component video input terminal. 9
qf t1Video input terminal 1. 8

PROG

6

KV-BZ21M40/BZ21P40/
BZ14M40/BZ14P40

1

(MONO)

(MONO)

qf

4

qs

23

qa

1

The earphone jack will be labeled as for KV-BZ14 only.

7

x Connecting optional components

Connecting to the video input terminal ( t )

TV front panel

KV-BZ21M50 KV-BZ21M40/

2

—R

L(MONO)—

TV rear panel

KV-BZ21M50 KV-BZ21M40/

1

BZ21P40/BZ14M40/
BZ14P40

*

2

—(MONO)

(MONO)—

BZ21P40/BZ14M40/
BZ14P40

*

1

Audio/Video cable

(not supplied)

Camcorder

Antenna cable
(not supplied)

(MONO)

L

R

(MONO)

(MONO)

Audio/Video cable

(not supplied)

VCR

DVD Player

* Sound Mix Terminal (

KV-BZ21M40/BZ21P40/BZ14M40/BZ14P40

only)

You can connect the audio L and R jacks from your AV equipment to both (MONO)
jacks on the TV to enjoy mixed left and right sound. If you do not prefer the mixed
sound, disconnect either one of the

Note

• If you connect a VCR to 8 (antenna input), preset the signal output from the VCR to the

program number 0 on the TV (see page 17).

(MONO) jacks.

Connecting to the monitor output terminal ( T )

TV rear panel

KV-BZ21M50 KV-BZ21M40/

(MONO)

L

R

BZ21P40/BZ14M40/
BZ14P40

Audio/Video

cable

(not supplied)

Audio system

VCR

8

Connecting to the component video input terminal ( )

B KV-BZ21M50 only

TV rear panel

1

(MONO) (MONO)

L

R

Y

C

B

L

C

R

R

Component video

cable

(not supplied)

DVD player

Audio cable

(not supplied)

Notes

• If your DVD player can output interlace and progressive mode signals, select the interlace
output when connecting to (component video input) on your TV. Your TV can receive
either 525i/60Hz or 625i/50Hz interlace signals.

• The component video terminals on your DVD player are sometimes labeled Y/CB/CR, Y/PB/
PR, Y/Cb/Cr or Y/B-Y/R-Y.

• If you select “DVD” on your TV screen, the signal from the T (monitor output) jacks will not
be output properly. This does not indicate a malfunction.

9

x Using the remote control and basic

functions

0

qa
qs

qd

qf

qg

qh

qj

qk
ql

w;

A/B

RETURN

1

4

7

3

2

6

5

9

8

0

PROG

WEGA
GATE

TV

Button Description Page

1 ?/1 Turn off temporarily or turn on –

1

2 a Display the TV program. –

2

3 Jump to last program number –

the TV.

that has been watched for at
least five seconds.

4 PROG +/– Select program number. –
52 +/– Adjust volume. –

3

8 Not function for your TV. –
9 Select surround mode options: 15

4

(KV-BZ21M50 “On”, “Simulated”, “Off”.

5

only)

0 Display on-screen information. –
qa Mute the sound. –

6

qd t Select TV or video input. 8
qf 0 – 9 Input numbers. –

7

ql Select sound mode options 15

8

(KV-BZ21M50 with a 5-Band Graphic

9

only) Equalizer display:

Dynamic

100 300 1k 3k 8k

Standard

100 300 1k 3k 8k

Custom

“Dynamic”, “Standard”,
“Custom”*.

* When the “Custom” mode is
selected, you can receive the last
adjusted sound settings from the
“Sound Adjustment” option in
the menu.

10

100 300 1k 3k 8k

w;

Select picture mode options: 14
“Vivid”, “Standard”, “Custom”*.

* When the “Custom” mode is
selected, you can receive the last
adjusted picture settings from
the “Picture Adjustment” option
in the menu.

Button Description Page
WEGA GATE menu operations

6 Confirm selected items. 12
7 WEGA GATE Display or cancel WEGA GATE menu.

qj V, v, B , b Select and adjust items.
qk RETURN Return to the previous level.

Timer operations

qg Set TV to turn on automatically according to the –

(Wake Up Timer)

desired period of time (max. of 12 hours).

The indicator on TV lights up amber once you set
the wake up timer.

If no buttons or controls are pressed for more than one
hour after the TV is turned on using the wake up timer,
the TV automatically goes into standby mode.

qh Set TV to turn off automatically according to the –

(Sleep Timer)

Teletext operations (green label)

desired period of time (max. of one hour and 30 min.).

, , , , Not function for your TV. –
, , , ,

(red, green,

yellow, blue)

PIP operations

, , V, v, B, b Not function for your TV.

Stereo/bilingual operations

–

qs A/B Not function for your TV. –

11

x Introducing the WEGA GATE

Confirm

Select

WEGA GATE

Settings

External Inputs

TV

navigator

WEGA GATE is a gateway that allows you to access to preset TV channels,
connected external inputs and “Settings” menu.

WEGA GATE
TV

Select

External Inputs
Settings

Confirm

“TV”

“External Inputs”

“Settings”

How to use WEGA GATE

WEGA GATE
TV

External Inputs
Settings

Select

(1) Press WEGA GATE to display or cancel

the WEGA GATE menu.

TV

01
02
03
04
05

Select

End

Confirm

Confirm

TV

01

02

03

04

05

Select

End

External Inputs

1

Video 1

Video 2

2

DVD

watch the preset TV
channels (see page 5)

Confirm

select the inputs for the
connected equipment
(see page 8)

Select
End

Picture Mode: Vivid

Picture Adjustment
Color Temperature: Cool
Intelligent Picture: On

Confirm

Picture

change the settings
of your TV
(see page 13)

Select

Confirm

TV

Select

End

End

01
02
03
04
05

Confirm

(3) Press V or v to select the desired item.

(2) Press (or b) to confirm your selection

or go to the next level.

(4) Press RETURN to move to the previous

level.

Tip

• The WEGA GATE, and V,v,B,b buttons on the top control panel can also be used for the
operations above.

12