Sony VGN-SR190 User Manual
VGN-SRxx Series Hard Disk Drive
These easy instructions are intended to guide you through the replacement process. If you need addi
tional
IMPORTANT!
PLEASE READ BEFORE YOU START
HDD Bay
2. 3.
Replacement Instructions
help, please call 1-866-651-7669 for technical support from 9:00 am to 11:00 pm EST.
ü To avoid electric shock, please make sure product is turned off and AC Adaptor is disconnected
* Sony is not responsible for any loss of data associated with your computer or any damage caused by incorrect handling of
the computer under these procedures. The terms of your Sony limited warranty continue to apply.
from the power source. Remove jewelry before you begin work to avoid scratching the surface of
your notebook computer.*
ü Place your notebook computer on a clean, stable and covered surface to avoid damage to the
computer’s case.*
ü Follow the ESD (Electrostatic Discharge) damage prevention instructions:
o Hold parts by the edges, away from exposed circuitry when possible.
o Do not walk around excessively as this promotes static build-up.
ü The appearance of the electronic components shown in the illustrations may be different from the
components shipped. This slight difference does not affect the accuracy of these instructions.
Step 1. Prepare the Computer.
CAUTION: Make sure the
computer is turned off, the lid is closed,
and the AC Adapter is disconnected.
Failure to do so can result in damage to
the computer.
Place the computer upside down on a
protected surface with the front edge
facing you.
1.
Push left tab in the unlock position
Lift to remove
Step 2. Remove the Battery Pack.
1. Slide the left battery tab to the
unlock position.
2. With your right thumb, slide the
right battery tab in the release
direction and hold.
3. Remove the battery by lifting the
side where the arrow is pointing.
(HDD Removal) Steps 3-7
Step 3. Locate the HDD Bay. Using the
enclosed magnetic screwdriver, loosen the
two (2) screws securing the HDD access
cover.
To remove the HDD access cover, start by
lifting from the side where the screws held
it in place.
FOR TECHNICAL SUPPORT IN THE US CALL TOLL FREE 1-866-651-7669 FROM 9:00 AM TO 11:00 PM EST
P/N Rev. X3 1/2
VGN-SRxx Series Hard Disk Drive
Replacement Instructions
Step 5. Using the enclosed magnetic
screwdriver, remove the two (2) screws
securing the HDD assembly.
Step 8. To remove the drive, carefully
detach HDD connector in the direction
shown. Some force may be needed to
unlock the HDD from the connector.
Step 6. Carefully lift the HDD assembly just
enough to access the HDD connector.
CAUTION: Do not force the removal
of the HDD at this point as damage to
the HDD cable/connector or drive may
occur.
(HDD Reinstallation) Steps 10-12
Step 9. Replace the old HDD assembly
with the new one. Carefully attach the HDD
connector to the replacement drive making
sure that they are seated properly.
Lift Plastic to Reveal Connector Location of HDD Connector
Step 7. Partially remove the black plastic
cover to get access to the HDD connector.
NOTE: The black plastic cover uses a thin
layer of adhesive tape to properly secure the
HDD to the connector. Slowly peel this
portion of the cover to reveal the connector.
Peel Adhesive Backing
Wrap Over HDD Connector
Step 10. Peel off the w hite adhesive backing
to expose the sticky portion of the mounting
tape. Wrap the black plastic cover over the
HDD connector to secure it in place.
Step 13. Reinstall the battery pack and
reconnect the AC Adaptor.
Power on your computer and continue with
the recovery process by following the
instructions described on the back of the
recovery disk’s case.
Return the old HDD to Sony following the
included shipping instructions.
Step 11. Carefully place the HDD assembly
inside the HDD Bay. Reinstall the two (2)
previously removed screws.
FOR TECHNICAL SUPPORT IN THE US CALL TOLL FREE 1-866-651-7669 FROM 9:00 AM TO 11:00 PM EST
P/N Rev. X3 2/2
Step 12. Re-attach the HDD access cover
and secure it with the two (2) screws
shown in the picture.
Loading...