Sony VAIO PCGA-PRF1 Service Manual

PCGA-PRF1 (UC/AEP/UK)

PCGA-PRF1

US Model

PCGA-PRF1 (UC/AEP/UK)

Connectors SERIAL Connector,RS-232C, D-

9-974-497-11

Specifications

SUB 9 pin (1)
PRINTER Connector, ECP, D­SUB 25 pin (1)
MONITOR Connector, analog
RGB, mini D-SUB 15 pin (1)
USB Connector, USB 4 pin (1)
NETWORK Connector,
10BASE-T (1)
MOUSE/KEYBOARD
Connector,PS/2, mini DIN 6
pin (2)

Canadian Model

AEP Model

Operating temperature

Dimensions Approx. 127/8× 111/16× 43/

Mass 470 g (14.3 oz.)
Supplied accessory

Design and specifications are subject to change
without notice.

41°Fto95°F(5°Cto35°C)

inches (w/h/d)

ox.

(Appr 324 × 42 × 109 mm)

Operating instructions (1)

8

UK Model

9-974-497-11

Sony Corporation

xxx

– 24 –

English

99x16xx-1

Printed in xxx

© 1999. x

xxx

99x16xx-1

Port Replicator

9-974-497-11

Information in this document is subject to change without
notice.

Sony and VAIO are trademarks of Sony. Intel logo and Intel
Inside logo are registered trademarks of Intel Corporation.
Pentium MMX is a trademark of Intel Corporation. Microsoft,
MS-DOS, Windows, the Windows 95 and Windows 98 logo
are trademarks of Microsoft Corporation.

Caution Markings for Lithium/Ion Battery - The following or
similar texts shall be provided on battery pack of equipment or
in both the operating and the service instructions.

CAUTION: Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equivalent type
recommended by the manufacturer. Discard used batteries
according to the manufacturer’s instructions.

All other trademarks are trademarks or registered trademarks
of their respective owners. Other trademarks and trade names
may be used in this document to refer to the entitles claiming
the marks and names or their produces. Sony Corporation
disclaims any proprietary interest in trademarks and trade names
other than its own.

Service and Inspection Precautions

1. Obey precautionary markings and
instructions

Labels and stamps on the cabinet, chassis, and components identify
areas requiring special precautions. Be sure to observe these
precautions, as well as all precautions listed in the operating manual
and other associated documents.

2. Use designated parts only

The set’s components possess important safety characteristics, such
as noncombustibility and the ability to tolerate large voltages. Be
sure that replacement parts possess the same safety characteristics as
the originals. Also remember that the ! mark, which appears in
circuit diagrams and parts lists, denotes components that have
particularly important safety functions; be extra sure to use only the
designated components.

CAUTION: The battery pack used in this device may present a
fire or chemical burn hazard if mistreated. Do not disassemble,
heat above 100°C (212°F) or incinerate.
Dispose of used battery promptly.
Keep away from children.

4. Inspect after completing service

After servicing, inspect to make sure that all screws, components,
and wiring have been returned to their original condition. Also check
the area around the repair location to ensure that repair work has caused
no damage, and confirm safety.

5. When replacing chip components...

Never reuse components. Also remember that the negative side of
tantalum capacitors is easily damaged by heat.

6. When handling flexible print boards...

•The temperature of the soldering-iron tip should be about 270C.

•Do not apply the tip more than three times to the same pattern.

•Handle patterns with care; never apply force.

3. Always follow the original design when
mounting parts and routing wires

The original layout includes various safety features, such as inclusion
of insulating materials (tubes and tape) and the mounting of parts
above the printer board. In addition, internal wiring has been routed
and clamped so as to keep it away from hot or high-voltage parts.
When mounting parts or routing wires, therefore, be sure to duplicate
the original layout.

PCGA-PRF1 (UC/AEP/UK)

Caution: Remember that hard disk drives are easily damaged by
vibration. Always handle with care.

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS P AR UNE MARQUE ! SUR LES
DIAGRAMMES SCHÉMA TIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

– 2 –

TABLE OF CONTENTS

Section Title Page

CHAPTER 1. OPERATION

1-1. Operating Instructions ..................................................... 1-1

(to 1-3)

CHAPTER 2. REMOVAL

2-1. Flowchart ......................................................................... 2-1

2-2. Assy Bottom .................................................................... 2-1

2-3. CNX-61 Board, Panel, CONN APR ................................ 2-2

(to 2-2)

CHAPTER 3. SELF DIAGNOSTICS

3-1. Required Tools and Peripheral Devices ........................... 3-1

3-2. Tools and Peripheral Device Connection......................... 3-3

3-3. How to Start the Disk-Based Diagnostics........................ 3-4

(to 3-4)

CHAPTER 4. BLOCK DIAGRAM......................... 4-1

(to 4-2)

CHAPTER 5. EXPLODED VIEWS AND

PARTS LIST ................................... 5-1

• Abbreviations
UC : US model / Canadian model

(to 5-2)

– 3 – PCGA-PRF1 (UC/AEP/UK)

CHAPTER 1.

OPERATION

1-1. Operating Instructions

English

Port Replicator

Operating Instructions

Warning

To prevent fire or shock hazard, do not
expose the unit to rain or moisture.

To avoid electrical shock, do not open
the cabinet. Refer servicing to qualified
personnel only.

Owner’s Record

The model number and serial number are located on
the bottom of your port replicator. Record the serial
number in the space providedhere. Refer to the model
and serial number when you call your Sony Service
Center.

Model No. PCGA-PRF1
Serial No. ___________________

PCGA-PRF1

(Extracted from 3-865-988-01 (1))

Specifications

Connectors SERIAL Connector, RS-232C, D-

Operating temperature

Dimensions Approx. 12

Mass 470 g (14.3 oz.)
Supplied accessory

Design and specifications are subject to change
without notice.

SUB 9 pin (1)
PRINTER Connector, ECP, D­SUB 25 pin (1)
MONITOR Connector,analog
RGB, mini D-SUB 15 pin (1)
USB Connector, USB 4 pin (1)
NETWORK Connector,
10BASE-T (1)
MOUSE/KEYBOARD
Connector,PS/2, mini DIN 6
pin (2)

41°Fto95°F(5°Cto35 C)

inches (w/h/d)
(Approx. 324 × 42 × 109 mm)

Operating instructions (1)

7

/8× 111/16× 43/

°

8

This product conforms with the following
European Directives:

73/23/EEC (Low Voltage Directive)
89/336/EEC, 92/31/EEC (EMC Directive)
93/68/EEC (CE-Marking Directive)

This equipment complies with EN55022 Class B
and EN50082-1 for use in the following areas:
residential, business, and light-industrial.

This equipment has been tested and found to
comply with the limits set out in the EMC
Directive using a connection cable shorter than
3 meters (9.8 feet).

Before use

Before using the port replicator, please read this
manual thoroughly and retain it for future
reference. See also the VAIO Notebook Computer
User Guide for more information.
The Sony PCGA-PRF1 is the port replicator
designed for a Sony Notebook Computer PCG­F100 series.
It cannot be used with any other computer.

Notes on use

• Do not place the unit in locations that are:
– Extremely hot or cold
– Dusty or dirty
– Very humid
– Vibrating
– Subject to strong magnetic fields
– Sandy
– Subject to direct sunlight

• Do not apply mechanical shock or drop the
unit.

• Be sure that nothing metallic comes into
contact with the metal parts of this unit. If
this happens, a short-circuit may occur and
the unit may be damaged.

• Do not operate the unit with a damaged
cord or if it has been dropped or damaged.

• Always keep the metal contacts clean.

• Do not disassemble or convert the unit.

• While the unit is in use, it gets warm; this is
normal.

• Keep the unit away from TV or AM
receivers, because it can disturb TV or AM
reception.

On cleaning

Clean the unit with a soft dry cloth, or a soft
cloth lightly moistened with a mild detergent
solution. Do not use any type of solvent, such
as alcohol or benzine, which may damage the
finish.

1-1 PCGA-PRF1 (UC/AEP/UK)

Français

PCGA-PRF1

Port Replicator

Mode d’emploi

Avertissement

Pour prévenir tout risque d’incendie ou
d’électrocution, garder cet appareil à
l’abri de la pluie et de l’humidité.

Pour prévenir tout risque
d’électrocution, ne pas ouvrir le boîtier.
Confier l’entretien de cet appareil
exclusivement au personnel qualifié.

Ce produit est conforme aux directives
européennes suivantes:

73/23/CEE (Basse tension)
89/336/CEE, 92/31/CEE (Directives CEM)
93/68/CEE (Marquage CE)

Cet équipement est conforme aux normes
EN55022 Classe B et EN50082-1, limitant
l’emploi dans les environnements résidentiel,
professionnel et industriel léger.

Cet appareil a été testé et déclaré conforme aux
limites de la Directive EMC lors de l’utilisation
d’un câble de liaison de moins de 3 mètres.

Spécifications

Connecteurs Série (SERIAL), RS-232C, D-

Température d’utilisation

Dimensions Approx. 324 × 42 × 109 mm

Masse Approx. 470g (14.3 li.)
Accessoire fourni

La conception et les spécifications sont sujettes
à modifications sans préavis.

SUBà9broches (1)
Imprimante (PRINTER), ECP,
D-SUB à 25 broches (1)
Moniteur (MONITOR), RVB
analogique, miniconnecteur D­SUB à 15 broches (1)
USB, USBà4broches (1)
Réseau (NETWORK),
10BASE-T (1)
Souris/Clavier (MOUSE/
KEYBOARD), PS/2,
miniconnecteur DIN à 6
broches (2)

à

5 °C35°C (41 °Fà95°F)

(l/h/p)
(Approx. 12
po.)

Mode d’emploi (1)

7

/8× 111/16× 43/

Remarques sur
l’utilisation

8

Avant utilisation

Avantd’utiliser cet réplicateur de port, lisez
attentivement le présent mode d’emploi et
conservez-le pour toute référence ultérieure.
Consultez également le Manual d’utilisation de
ordinateur bloc-notes VAIO.
Le PCGA-PRF1 Sony est le réplicateur de port
conçu pour un ordinateur bloc-notes Sony série
PCG-F100.
Il ne peut être utilisé avec un autre ordinateur.

• Ne placez pas l’appareil dans des endroits :
– extrêmement chauds ou froids;
– poussiéreux ou sales;
– très humides;
– soumis à des vibrations;
– soumis à de puissants champs

magnétiques;
– sablonneux;
– exposés au rayonnement direct du soleil.

• Ne soumettez pas l’appareil à des chocs
mécaniques et ne le laissez pas tomber.

• Veillez à ce qu’aucun objet métallique
n’entre en contact avec les parties
métalliques de cet appareil. Si cela se
produit, un court-circuit risque de survenir
et d’endommager l’appareil.

• Ne faites pas fonctionner l’appareil avec un
câble endommagé ou s’il est tombé et a subi
des dommages.

• Veillez à ce que les contacts métalliques
restent toujours propres.

• Ne démontez pas et ne transformez pas
l’appareil.

• Le système chauffe en cours d’utilisation.
C’est normal.

• Gardez l’appareil à l’écart des téléviseurs et
des récepteurs AM, il peut causer des
interférences dans la réception télévisée ou
radiophonique.

Entretien

Nettoyez l’appareil au moyen d’un chiffon sec
et doux, ou légèrement imprégné d’une
solution détergente neutre. N’utilisez aucun
type de solvant, comme de l’alcool ou de la
benzine, qui risquerait de ternir le fini de
l’appareil.

1-2PCGA-PRF1 (UC/AEP/UK)