Sony TRINITRON KV-32WS2U, TRINITRON KV-32WS2B, TRINITRON KV-32WS2D Service Manual

SELF-DIAGNOSTIC FUNCTION

MICROFILM

SERVICE MANUAL BE-3D CHASSIS

MODEL

COMMANDER DEST CHASSIS NO.

KV-32WS2B KV-32WS2D

RM-862 French SCC-K01V-A

RM-862 AEP SCC-K07W-A

MODEL

COMMANDER DEST CHASSIS NO.

KV-32WS2U

RM-862 UK SCC-K04R-A

T RIN IT RON

1

®

COLOR TV

®

ITEM MODEL Television System Stereo System Channel Coverage Color System

VHF : E2-E12, S01-S03, R1-RX11,

French B/G/H, D/K, L, I GERMAN/NICAM

Stereo

F2-F10, B-Q UHF : E21-E69, - B21-B69, R21-R69, F21-F61 CABLE TV : S1-S20 HYPER : S21-S41

PAL, SECAM NTSC4.43, NTSC3.58 (VIDEO IN)

VHF : E02-E12, R01-R12, A-H2 UHF : E21-E69, - R21-R69

AEP B/G/H, D/K GERMAN Stereo

UK I NICAM Stereo UHF : B21-B69

MODEL 32WS2B 32WS2D 32WS2U

Power Consumption 105 W 105 W 163 W

[PICTURE TUBE] Super Trinitron Wide

CABLE TV : S01-S05, S1-S20 HYPER : S21-S41

[FRONT]

Approx. 82cm (32 inches) (Approx. 76 cm picture measured diagonally) 110 degree deflection

Input/Output Terminals

Sound output

[REAR]

1 21-pin Euro connector (CENELEC standard).

- Inputs for Audio and Video signals.

- Inputs for RGB.

- Outputs of TV Video and A ud i o s ign a l s.

21-pin Euro connector.

- inputs for A ud i o an d Video signals.

- inputs for S Video.

- outputs for Audio and Video signals (selectable). Phono Jack

- Outputs for Audio Signals Left/Right Speaker Terminals Surround Speaker Terminals

Left/Right 2x15W (Music Power) Centre 2x5W (Music Power) Surround 2x10W (Music Power) Power requirements 220 - 240V Dimensions Approx 906x552x566mm approx. Weight Approx 60kg Supplied accessories RM-862 Remote Commander (1)

Other features Dolby Pro Logic, NICAM*, FASTEXT

[RM-862]

Remote control system infrared control Power requirements 3V dc

Dimensions Approx 210x56x24mm (w/h/d) Weight Approx 110g (Not including battery)

PAL, SECAM NTSC4.43, NTSC3.58 (VIDEO IN)

PAL NTSC4.43, NTSC3.58 (VIDEO IN)

Video input - phono jack Audio inputs - phono jacks S Vid eo i np ut 4 pin DIN

Headphone jacks : stereo minijack

IEC designated R6 battery (2)

(KV-32WS2B/32WS2U only)

*

2 batteries IEC designation R6 (size AA)

Design and specifications are subject to change without notice.

2

Model Name

ASA

T

How to replace the fuse. Open the fuse compartment with a screwdriver blade and replace the fuse.

FUSE

Item Pal Comb OFF OFF OFF PIP OFF OFF OFF Woofer Box OFF OFF OFF Scart 1 ON ON ON Scart 2 ON ON ON Front in (3) ON ON ON Scart 4 OFF OFF OFF Projector OFF OFF OFF AKB in 16:9 mode ON ON ON Norm B/G/H ON ON OFF Norm I ON OFF ON Norm D/K ON ON OFF Norm AUS OFF OFF OFF Norm L ON OFF OFF

KV-32WS2B KV-32WS2D KV -32WS2U

Norm SAT OFF OFF OFF Norm M OFF OFF OFF Teletext ON ON ON Nicam Stereo ON OFF ON Language Preset French German English

WARNING (KV-32WS2U only)

The flexible mai ns lead is supplied connected to a B.S. 1363 fused plug having a fuse of 5 AMP capacity. Should the fuse need to be replaced, use a 5 AMP FUSE approved by ASTA to BS 1362, ie one that carr ie s the the mark. IF THE PLUG SUPPLIED WITH THIS APPLIANCE IS NOT SUITABLE FOR THE OUTLET SOCKETS IN YOUR HOME, IT SHOULD BE CUT OFF AND AN APPROPRIATE PLUG FITTED. THE PLUG SEVERED FROM THE MAINS LEAD MUST BE DESTROYED AS A PLUG WITH BARED WIRES IS DANGEROUS IF ENGAGE D IN A LIVE OUTLET SOCKET. When an alte rnative type of plug is used it should be fitted with a 5 AMP FUSE, otherwise the circuit shoul d be protected by a 5 AMP FUSE at the distribution board.

3

21 pin connector ( 1, 2 / 2 )

21

20

19

18

17

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

Pin No 1 2 4 Signal Signal level

1 Audio output B

2

3 4 Ground (audio) 5 Ground (blue) 6 Audio input A

7 Blue input 0.7 +/- 3dB, 75 ohms positive

8 Function select

9 Ground (green) 10 Open 11 Green Green signal : 0.7 +/- 3dB, 75 ohms,

12 Open 13 Ground (red) 14 Ground (blanking)

15

_ (S signal Chroma

16 Blanking input

17 Ground (video

18 Ground (video

19 Video output 1V +/- 3dB, 75ohms, positive sync 0.3V

20

_ Video input

21 Common ground

(right) Audio output B

(right) Audio output A

(left)

(AV control)

_ _ Red input 0.7 +/- 3dB, 75 ohms, positive

input)

(Ys signal)

output)

input)

_ _ Video input 1V +/- 3dB, 75ohms, positive sync 0.3V

Y (S signal)

(plug, shield)

Standard level : 0.5V rms Output impedence : Less than 1kohm*

Standard level : 0.5V rms Output impedence : More than 10kohm*

Standard level : 0.5V rms Output impedence : Less than 1kohm*

Standard level : 0.5V rms Output impedence : More than 10kohm*

High state (9.5-12V) : Part mode Low state (0-2V) : TV mode Input impedence : More than 10K ohms Input capacitance : Less than 2nF

positive

0.3 +/- 3dB, 75 ohms, positive

High state (1-3V) Low state (0-0.4V) Input impedence : 75 ohms

(-3+10dB)

(-3+10dB) 1V +/- 3dB, 75ohms, positive sync 0.3V

(-3+10dB)

Connected Not Connected (open) * at 20Hz - 20kHz

Pin No Signal Signal level

1 Ground 2 Ground 3 Y (S signal) input 1V+/- 3dB 75 ohm, positive Sync 0.3V -3/+10dB 4 C (S signal) input 0.3V+/- 3dB 75 ohm, positive Sync

4

TABLE OF CONTENTS

Section Title Page Section Title Page

1. GENERAL

5. DIAGRAMS

Overview .....................6

Getting Started .....................8

TV Operation ................... ..9

Advanced Operations .....................10

Teletext .....................16

Optional Equipment .....................17

Troubleshooting .....................19

2. DISASSEMBLY

2-1. Rear Cover Removal .....................20

2-2. Speaker Removal .....................20

2-3. Chassis Assy Removal .....................20

2-4-1. Service Position (1) .....................20

2-4-2. Service Position (2) .....................21

2-5. A Board Removal ................... ..21

2-6. A Extension Board ................... ..21

2-7. A1 Extension boards .....................21

2-8. Picture Tube Removal .....................22

Removal of Anode Cap .....................22

Removal and Replacement of the

Main - Bracket Bottom Plates .....................23

3. SET-UP ADJUSTMENTS

3-1. Beam Landing .....................24

3-2. Convergence .....................25

3-3. White Balance ..... ................27

5-1. Block Diagrams .....................35

5-2. Circuit Board Location .....................43

5-3. Schemati c Diagrams and

Printed Wiring Boards .....................43

* K1 Board .....................44

* D Board .....................51

* A Board .....................56

* C Board .....................66

* VM Board .....................67

* A1 Board .....................71

* J Board .....................72

* D4 Board .....................74

* IF Board

[VIF (AEP), VIF UK] ............. .... ... .77

* IF Board [VIF (FR)] .....................77

IC Blocks .....................79

5-4. Semiconductors .....................81

6. EXPLODED VIEWS

6-1. Chassis .................... .83

6-2. Picture Tube .....................84

7. ELECTRICAL PARTS LIST .....................85

4. CIRCUIT ADJUSTMENTS

4-1. Electrical Adjustments .....................28

4-2. Test Mode 2 .....................31

4-3. BE-3D Self Diagnostic Software .....................33

CAUTION

SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR THE CARBON PAINTED ON THE CRT, AFTER REMOVAL OF THE ANODE CAP

WARNING !!

AN ISOLATING TRANSFORMER SHOULD BE USED DURING ANY SERVICE WORK TO AVOID POSSIBLE SHOCK HAZARD DUE TO LIVE CHASSIS. THE CHASSIS OF THIS RECEIVER IS DIRECTLY CONNECTED TO THE POWER LINE.

SAFETY-RELATED COMPONENT WARNING !!

COMPONENTS IDENTIFIED BY SHADING AND MARKED ON THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE P ART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION

APRES AVOIR DECONNECTE LE CAP DE’LANODE, COURT-CIRCUITER L’ANODE DU TUBE CATHODIQUE ET CELUI DE L’ANODE DU CAP AU CHASSIS METALLIQUE DE L’APPAREIL, OU AU COUCHE DE CARBONE PEINTE SUR LE TUBE CATHODIQUE OU AU BLINDAGE DU TUBE CATHODIQUE.

ATTENTION !!

AFIN D’EVITER TOUT RISQUE D’ELECTROCUTION PROVENANT D’UN CHÁSSIS SOUS TENTION, UN TRANSFORMATEUR D’ISOLEMENT DOIT ETRE UTILISÈ LORS DE TOUT DÈPANNAGE. LE CHÁSSIS DE CE RÈCEPTEUR EST DIRECTMENT RACCORDÈ Á L’ALIMENTATION SECTEUR.

ATTENTION AUX COMPOSANTS RELATIFS Á LA

SÈCURITÈ !!

LES COMPOSANTS IDENTIFIÈS PAR UNE TRAME ET PAR UNE MARQUE SUR LES SCHÈMAS DE PRINCIPE, LES VUES

EXPLOSÈES ET LES LISTES DE PIECES SONT D’UNE IMPORTANCE CRITIQUE POUR LA SÈCURITÈ DU FONCTIONNEMENT, NE LES REMPLACER QUE PAR DES COMPSANTS SONY DONT LE NUMÈRO DE PIÈCE EST INDIQUÈ DANS LE PRÈSENT MANUEL OU DANS DES SUPPLÈMENTS PUBLIÈS PAR SONY.

5