Sony Trinitron KV-28FS20U User Manual

Trinitron Colour Television

4-205-420-62

420542062

Instruction Manual

This Instruction Manual has been produced using Totally chlorine free (TCF) 100% Re-cycled paper

to comply with our commitment to the use of environmentally friendly materials in our products.

KV-28FS20U

NOTICE FOR CUSTOMERS IN THE UNITED KINGDOM

A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience. Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or BSI to BS 1362 (i.e. marked with or ) must be used. When an alternative type of plug is used it should be fitted with a 5 AMP FUSE, otherwise the circuit should be protected by a 5 AMP FUSE at the distribution board. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station.

How to replace the Fuse

Open the fuse compartment with a blade screwdriver, and replace the fuse.

• IMPORTANT

If the plug supplied is not suitable for the socket outlet in your home, it should be cut off and an appropriate plug fitted in accordance with the following instructions: The wires in this mains lead are coloured in accordance with the following code: Blue Neutral Brown Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. Do not connect either wire to the earth terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured green or green and yellow.

ASA

FUSE

WARNING

• To prevent shock hazard, do not insert the plug cut off from the mains lead into a socket outlet. This plug cannot be used and should be destroyed.

• To prevent fire or shock hazard, do not expose the unit to rain or moisture.

• Dangerously high voltages are present inside the set. Do not open the cabinet. Refer servicing to qualified personnel only.

Table of Contents

Getting Started

Checking the accessories supplied Inserting batteries into the remote control Connecting the speakers Connecting the aerial Switching on the TV Automatically tuning the TV

Overview

Overview of the TV set buttons Overview of the remote control buttons

Additional TV Features

Choosing a language for the TV menu screens Automatically tuning the TV Re-arranging the TV channels Adjusting the picture Changing picture and sound modes quickly Adjusting the sound Setting up Dolby Pro Logic Changing the screen mode Using the further programme preset feature Adjusting the picture rotation Using the parental lock Using the sleep timer Manually tuning the TV Skipping programme positions Naming a channel

2 2 3 5 5 6

7 8

9 10 11 12 12 13 14 15 16 17 17 18 19 20 21

Teletext

Switching teletext on and off Using other teletext functions

Optional Equipment

Connecting equipment to the TV Additional information when connecting equipment to the TV Selecting the output source for the scart socket Using the ‘AV Label Preset’ feature

Additional Information

Specifications Troubleshooting

22 22

23 23 24 25

26 27

Getting Started

Follow steps 1-6 to: Check the accessories supplied

Insert batteries into your remote control Connect the speakers Connect the aerial to your TV Plug in and switch on the TV View programmes on your TV

1. Checking the accessories supplied

Surround speakers

Centre speaker

Batteries

Remote control

2. Inserting batteries into the remote control

Always remember to dispose of used batteries in an environmentally friendly way.

Getting Started

3.1. Connecting the speakers

Before switching on the TV, please connect the speakers to the TV using the leads provided. Connect the striped lead to the red terminals and the black lead to the black terminals.

Dolby* ProLogic Surround normally requires 5 speakers:

Centre Speaker - to anchor the fixed sounds, like dialogues, to the screen. Left and Right Front Speakers (incorporated in the TV) - for the normal two channel stereo or bilingual broadcasts. Surround Speakers - for the special effects created by the surround channels.

To connect the speakers provided:

Centre speaker

Connect black leads to black terminals

D/D

S/I

L/G/

R/D/

Connect striped leads to red terminals

Black lead

Striped lead

Surround speakers **

* Manufactured under licence from Dolby Laboratories Licensing Corporation. ‘Dolby’, ‘ProLogic’, and the double D symbol are trademarks of the Dolby Laboratories Licensing Corporation.

** For the best sound effects, place the surround speakers one meter above your listening position.

Getting Started

3.2. Connecting the speakers

To connect your own speakers (when using your own speakers, make sure they are at least 4 ohms impedance and magnetically shielded)

Connect black leads to black terminals

Connect striped leads to red terminals

R/D/ D/D

L/G/ S/I

Right speaker

Centre speaker

Surround speakers

Black lead

Striped lead

Left speaker

Note: When you connect your own external left and right speakers you must mute the internal speakers by pressing in the button marked on the rear of the TV.

Getting Started

4. Connecting the aerial

Connect your existing aerial to the socket marked on the rear of the TV.

5. Switching on the TV

Connect the TV plug to the mains socket (220-240V AC, 50Hz) and switch socket on.

Push in the on/off switch on the front of the TV.

Getting Started

6. Automatically tuning the TV

When you first switch on the TV, the following sequence of menu screens appear on the TV enabling you to 1) choose a language for the TV menu screens, 2) tune channels to the TV, 3) arrange the channels.

1. When switching on the TV for the first time, the ‘LANGUAGE’ menu appears automatically on the TV screen enabling you to select in which language you wish

to read the TV menu screens. Press the the remote control to select your chosen language then press the OK button to confirm your selection.

2. The ‘automatic tuning’ menu appears on the TV screen in your selected language. Press the ‘YES’ then press the OK button to confirm.

V or v buttons on

V or v buttons to select

Do you want to start automatic tuning?

Yes No

Confirm: OK

3. Ensure the antenna is connected as instructed, then press the OK button to confirm. The TV starts to automatically search and store all available channels for you. Please be patient and do not press any buttons.

4. When the TV has finished tuning in all available channels, the ‘PROGRAMME SORTING’ menu appears on the TV screen enabling you to change the order of the

channels on your TV. If you do not wish to use this option, proceed to step 5.

If you wish to change the channel order, press the buttons on your remote control to select the channel you want to move, then press the OK button. Press the buttons to select the new programme number position for your selected channel then press the OK button to confirm. The selected channel now moves to its new programme position. Repeat this procedure if you wish to sort the order of other channels on your TV.

5. Press the MENU button to remove the menu from the TV screen.

V or v

Please confirm that antenna is connected

Confirm: OK

6. Press the PROGR+/- or the numbered buttons on the remote control to view the TV channels.

Overview

Overview of the TV set buttons

On/Off switch.

Press to switch TV on and off.

Video input button.

Press to select the input signals from VCR etc.

Volume control buttons.

Press to increase(+)/decrease(-) volume.

Auto tune button.

Press to select the automatic tuning function.

Programme Up or Down buttons.

Press to increase(+)/decrease(-) channels.

+ 21 hidden pages