Sony Trinitron KV-14V6U, Trinitron KV-14V5U, Trinitron KV-21V5U, Trinitron KV-21V6U User Manual

3-860-137-21 (1)

KV-14V5U KV-14V6U

KV-21V5U KV-21V6U

Operating Instructions

Trinitr on Colour Video TV

PAL NTSC 4.43

WARNING

To prevent fire or shock hazard, do not expose the unit to rain or moisture. Dangerously high voltages are present inside the set. Do not open the cabinet. Refer servicing to qualified personnel only.

Caution

Television programmes, films, video tapes and other materials may be copyrighted. Unauthorized recording of such materials may be

contrary to the provisions of the copyright laws.

Colour System of Your Set

This video TV is designed to receive TV programmes based on PAL (I) colour system and to record and play on PAL colour system. The video TV can also play tapes on NTSC colour system.

Precautions

Safety Information

For general safety:

• Do not expose the unit to rain or moisture.

• Do not open the rear cover.

For safe operations:

• Do not operate the unit on anything but 220–240 V AC,

50 Hz.

• Do not operate the unit if any liquid or solid object falls

in it—have it checked immediately.

• Unplug the unit from the wall outlet if you do not

intend to use it for an extended period of time. To disconnect the cord, pull it out by the plug, never by the

cord.

NOTICE FOR CUSTOMERS IN THE UNITED KINGDOM

A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience. Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or BSI to BS 1362 (i.e. marked with 2 or @ must be used. When an alternative type of plug is used it should be fitted with a 5 AMP FUSE, otherwise the circuit should be protected by a 5 AMP FUSE at the distribution board. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station.

For safe installation:

• Leave a clear space of 5 cm around the unit for

adequate ventilation.

• Do not install the unit in hot, humid, or excessively

dusty places.

• Do not install the unit where it may be exposed to

mechanical vibrations.

For your protection, refer all servicing to qualified personnel.

About Moisture Condensation

If the unit is brought directly from a cold place to a warm place, moisture may condense on the video head drum. If this happens, the tape may stick to the head drum and it may be damaged or the unit may not operate correctly. To avoid possible damage caused by moisture condensation, be sure not to leave a cassette inside the compartment when the unit is not in use. When bringing the unit from a cold place to a warm place, wait for about 10 minutes before operating it. If the tape operation buttons do not work due to moisture condensation, leave the power on for more than one hour.

rIMPORTANT

If the plug supplied is not suitable for the socket outlets in your home, it should be cut off and an appropriate plug fitted in accordance with the following instructions: The wires in this mains lead are coloured in accordance with the following code: Blue Neutral Brown Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. Do not connect either wire to the earth terminal in the plug which is marked by the letter E or by the safety earth symbol Y or coloured green or green and yellow.

rWARNING

To prevent shock hazard, do not insert the plug cut off from the mains lead into a socket outlet. This plug cannot be used and should be destroyed.

rTo prevent fire or shock hazard, do not expose the unit

to rain or moisture.

rDangerously high voltages are present inside the set.

Do not open the cabinet. Refer servicing to qualified personnel only.

How to replace the fuse

Open the fuse compartment with a blade screwdriver, and replace the fuse.

Getting Started

FUSE

Contents

Getting Started

Step 1—Preparation ................................................... 4

Checking the supplied accessories .......................4

Inserting batteries into the remote

control.................................................................... 4

Step 2—Connecting the Aerial ................................. 5

Connecting an indoor aerial (KV-14V5U,

KV-14V6U only) ................................................... 5

Connecting an outdoor aerial................................5

Step 3—Tuning in to TV Stations .............................6

Selecting the menu language................................. 6

Presetting channels automatically ........................ 7

Presetting channels manually ............................... 8

Skipping programme positions ............................ 9

Captioning a TV station name ............................ 10

Manual fine-tuning ............................................... 11

Tuning in to a channel temporarily.................... 12

Setting a Pay-TV channel (KV-14V6U,

KV-21V6U only) ................................................. 13

Step 4—Setting up VIDEO Plus+* Manually........ 14

Setting the guide channels ................................... 14

Step 5—Setting the Clock ........................................ 16

Basic Operations

Watching the TV .......................................................17

Switching the video TV on and off..................... 17

Selecting TV programmes.................................... 17

Adjusting the volume ........................................... 17

Adjusting the picture............................................ 18

Muting the sound..................................................19

Displaying the on-screen information ............... 19

Watching line input .............................................. 19

Listening with headphones ................................. 19

Viewing Teletext ....................................................... 20

Switching Teletext on and off.............................. 20

Using Fasttext ........................................................ 20

Playing a Tape........................................................... 22

Inserting a video cassette ..................................... 22

Ejecting a video cassette ....................................... 22

Protecting your cassette against accidental

erasure ................................................................ 22

Playing a tape ........................................................ 23

Resetting the tape counter ................................... 23

Playing a tape repeatedly (AUTO REPEAT) .... 24

Replaying a scene automatically......................... 24

Setting the colour system ..................................... 25

Displaying the on-screen indications ................. 25

Viewing programmes in 16:9 mode ................... 26

Recording TV Programmes..................................... 27

Recording TV programmes ................................. 27

Recording with the TV off ................................... 27

Watching a TV programme while recording

another (KV-14V6U, KV-21V6U only) ............ 27

Recording TV Programmes Using the Timer .......28

Setting the timer ....................................................28

Using the video TV before timer recording

starts.....................................................................30

Checking the timer settings ................................. 31

Changing or cancelling the timer settings......... 31

Recording using QUICK TIMER ........................ 32

Timer recording with PDC signals ..................... 33

Recording TV Programmes Using VIDEO

Plus+ ....................................................................... 34

Additional Operations

Switching Off Automatically—Sleep Timer .........36

Switching On at Your Desired Time—

On Timer ................................................................ 37

Using FUNCTION LOCK ....................................... 38

Searching Using the INDEX Function ................... 39

Enhancing Video Picture Quality........................... 40

Adjusting the tracking.......................................... 40

Adjusting with the optimum picture control

(OPC) ................................................................... 41

About the Auto Head Cleaner ............................ 41

Connecting Optional Equipment ........................... 42

Watching the picture input from optional

equipment ...........................................................42

Editing with another VCR ................................... 43

Watching the Pay-TV channel (KV-14V6U,

KV-21V6U only) ................................................. 43

Additional Information

Troubleshooting........................................................ 44

Taking Care of Your Video TV ...............................46

Video head cleaning ............................................. 46

Worn video heads .................................................46

Check the video heads after 1,000 hours

of use.................................................................... 46

Specifications............................................................. 47

Television Channel Number Guide ....................... 48

Index to Parts and Controls .................................... 49

Video TV set—front .............................................. 49

Remote control ...................................................... 50

* VIDEO Plus+ and PlusCode are trademarks applied for by

Gemstar Development Corp. VIDEO Plus+ system is manufactured under license from Gemstar Development Corporation.

The instructions in this manual are for models KV-14V5U, KV-14V6U, KV-21V5U and KV21V6U. Before you begin to read this manual, refer to the model number located on the rear of your video TV. Model KV-14V6U is used for illustration purposes throughout this manual. Any differences in operation are indicated in the text, for example, “KV-14V5U, KV-14V6U only.”

Getting Started

Step 1 — Preparation

Checking the supplied accessories

When you have taken everything out of the carton, check that you have these items:

• Remote control

• Two R6 (size AA) batteries

• Loop aerial (KV-14V5U, KV-14V6U only)

(KV-14V5U, KV-14V6U only)

Inserting batteries into the remote control

Close the cover.

Turn the remote control over, and remove the cover.

Check the polarities and position two R6 batteries correctly.

Note

Always remember to dispose of used batteries in an environmentally friendly way.

Getting Started

Step 2 — Connecting the Aerial

Connecting an indoor aerial (KV14V5U, KV-14V6U only)

If your local VHF/UHF signal is strong, an indoor aerial can be used to obtain a clear picture. Connect the supplied loop aerial as follows:

1 Insert the aerial until it clicks. 2 Connect to the ˘ (aerial) socket.

After turning on the video TV, adjust the aerial for the best reception. Be sure to adjust the aerial for the channel you want to record as well. If reception is poor, connect an outdoor aerial to your video TV.

Aerial connector (supplied)

Note

Do not use the supplied loop aerial with any other TV product.

Connecting an outdoor aerial

For better TV reception and clearer recording, connect an outdoor aerial to your video TV.

To connect a VHF aerial or a combination VHF/UHF aerial—75-ohm coaxial cable (round)

Attach an IEC aerial connector to 75-ohm coaxial cable. Plug the connector into the (aerial) socket, located at the rear of the video TV.

Rear

To connect both VHF and UHF aerials

Attach the aerial cable ends to the VHF/UHF mixer (not supplied). Plug the mixer into the (aerial) socket, located at the rear of the video TV.

Rear

300-ohm twin-lead cable

VHF/UHF aerial

UHF aerial

On a wall

VHF aerial

VHF/UHF mixer

75-ohm coaxial cable

After connecting the aerial, connect the mains lead to a wall outlet.

Getting Started

Step 3 — Tuning in to TV Stations

You can preset up to 80 TV channels, either automatically or manually. The automatic method is easier if you want to preset all receivable channels at once. Use the manual method if you want to allocate

TIMER

programme numbers to the channels one by one.

SLEEP



VIDEO Plus+

TIMER

ON SCREEN

TIMER REC

ON/OFF

TIMER REC

CLEAR

REC

REPLAY

REW

1 4 7

-/--

QUICK TIMER

INDEX SEARCH

PLAY

STOP

2 5 8 0

TAPE

SPEED

3 6 9

PROGR

COUNTER

RESET

PAUSE

Before you begin

• Depress the U (MAIN POWER) switch, located behind the cover on the front of the video TV, to turn the TV on. If the u lamp on the video TV is lit in red (indicating that the video TV is in standby mode), press ;, PROGR +/– or a number button on the remote control.

Selecting the menu language

You can select one of several languages for the menu and on-screen information. The initial setting is English.

1 Press MENU.

The main menu appears.

PICTURE CONTROL ON TIMER SET CLOCK SET LANGUAGE PROGRAMME PRESET VCR MODE FUNCTION LOCK

Sapelect nd ress

Getting Started

2 Move the cursor (z) to “LANGUAGE” with + ◊ or – √ and press OK.

The LANGUAGE menu appears.

LANGUAGE

ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS PORTUGUÊS

Sape l ec t nd r es s

3 Select the language you want with + ◊ or – √ and press OK.

The selected language is coloured green, and the menu appears in the selected language.

4 Press MENU to return to the original screen.

Presetting channels automatically

1 Press MENU to display the main menu.

TIMER

SLEEP

VIDEO Plus+

TIMER

ON SCREEN

TIMER REC

ON/OFF

TIMER REC

CLEAR

REC

REPLAY

REW

1 4 7

-/--

QUICK TIMER

INDEX SEARCH

PLAY

STOP

2 5 8 0

TAPE

SPEED

3 6 9

PROGR

COUNTER

RESET

PAUSE

2 Move the cursor (z) to “PROGRAMME PRESET” with + ◊ or – √ and

press OK. The PROGRAMME PRESET menu appears.

PROGRAMME PRESET

AUTO PROGRAMME MANUAL PROGRAMME SET UP GUIDE CH

Sape l ec t nd r es s

3 Move the cursor (z) to “AUTO PROGRAMME” with + ◊ or – √ and press

OK. The AUTO PROGRAMME menu appears.

AUTO PROGRAMME SYSTEM

Sape l ec t nd r es s

PROG CH

–– –––

4 Press OK.

The programme number you previously watched appears in red in the “PROG” position. Using + ◊ or – √, select the programme number from which you want to start presetting and press OK. You cannot begin presetting at 00. The CH position turns red.

To stop automatic channel presetting

Press ? on the remote control.

AUTO PROGRAMME SYSTEM

Sape l ec t nd r es s

PROG

01 C22

5 Select the channel with + ◊ or – √ and press OK.

The video TV starts scanning and presetting all receivable channels from the programme number selected in step 4. The preset programme and channel numbers are displayed on the screen in sequence. When presetting is finished, the original screen reappears. All available channels are now stored on successive number buttons.

Getting Started

Presetting channels manually

1 Press MENU to display the main menu.

TIMER

SLEEP

VIDEO Plus+

TIMER

ON SCREEN

TIMER REC

ON/OFF

TIMER REC

CLEAR

REC

REPLAY

REW

1 4 7

-/--

QUICK TIMER

INDEX SEARCH

PLAY

STOP

2 5 8 0

TAPE

SPEED

3 6 9 C

PROGR

COUNTER

RESET

PAUSE

2 Move the cursor (z) to “PROGRAMME PRESET” with + ◊ or – √ and

press OK. The PROGRAMME PRESET menu appears.

PROGRAMME PRESET

AUTO PROGRAMME MANUAL PROGRAMME SET UP GUIDE CH

Sapelect nd ress

3 Move the cursor (z) to “MANUAL PROGRAMME” with + ◊ or – √ and

press OK. The MANUAL PROGRAMME menu appears.

MANUAL PROGRAMME PRG

SYS I

1 C22 –– –

C24 ––––– ON

C26 ––––– ON

C32 ––––– ON

C36 ––––– ON

C38 –––––ION

LABEL AFT

ndSelect press

–– ON

D – – – – – –

4 Using + ◊ or – √, move the cursor (z) to the programme position (number

button) to which you want to preset the channel, and press OK. The SYS position turns red.

For programme positions beyond 6

The display scrolls by pressing – √ repeatedly.

If you have made a mistake

Press ? to return to the previous position.

MANUAL PROGRAMME PRG

SYS I

1 C22 –– –

C24 ––– – – ON

C26 ––– – – ON

C32 ––– – – ON

C36 ––– – – ON

C38 ––– – –ION

LABEL AFT

ndSelect press

–– ON

D – – – – – –

5 Select the system with + ◊ or – √ and press OK.

The CH position turns red.

6 Select the channel you want to preset with + ◊ or – √ and press OK. 7 The video TV starts scanning receivable channels. When the channel is

found, it stops. If you want to preset this channel, press OK. If not, press + ◊ or – √ to search for another channel.

8 Repeat steps 4 through 7 to preset other channels. 9 After you finish presetting, press MENU to return to the original screen.

Getting Started

TIMER

SLEEP

Skipping programme positions

You can skip unused programme positions when selecting programmes with PROGR +/– buttons.

1 Press MENU to display the main menu.

VIDEO Plus+

TIMER

ON SCREEN

TIMER REC

ON/OFF

TIMER REC

CLEAR

REC

REPLAY

REW

1 4 7

-/--

QUICK TIMER

INDEX SEARCH

PLAY

STOP

2 5 8 0

TAPE

SPEED

3 6 9

PROGR

COUNTER

RESET

PAUSE

2 Move the cursor (z) to “PROGRAMME PRESET” with + ◊ or – √ and

press OK. The PROGRAMME PRESET menu appears.

3 Move the cursor (z) to “MANUAL PROGRAMME” with + ◊ or – √ and

press OK. The MANUAL PROGRAMME menu appears.

4 Using + ◊ or – √, move the cursor (z) to the programme position which

you want to skip and press OK. The “SYS” position turns red.

MANUAL PROGRAMME PRG

SYS I

1 C22 –– –

C24 ––––– ON

C26 ––––– ON

C32 ––––– ON

C36 ––––– ON

C38 –––––ION

LABEL AFT

ndSelect press

–– ON

D – – – – – –

5 Press + ◊ or – √ until “---” appears in the “SYS” position and press OK.

MANUAL PROGRAMME PRG SYS

1 C22 –– –

C24 ––––– ON

C26 ––––– ON

–––

C32 ––––– ON

C36 ––––– ON

C38 –––––ION

LABEL AFT

aOKndSelect press

–– ON

D – – – – – –

For programme positions beyond 6

The display scrolls by pressing – √ repeatedly.

When you select programmes using the PROGR +/– buttons, the programme position is skipped.

6 Repeat steps 4 and 5 to skip other programme positions. 7 Press MENU to return to the original screen.

Getting Started

TIMER

Captioning a TV station name

You can name a channel using up to five characters (letters or numbers) to be displayed on the TV screen (e.g. MTV). Using this function, you can easily identify which channel you are watching.

SLEEP

VIDEO Plus+

TIMER

ON SCREEN

TIMER REC

ON/OFF

TIMER REC

CLEAR

REC

REPLAY

REW

1 4 7

-/--

QUICK TIMER

INDEX SEARCH

PLAY

STOP

2 5 8 0

TAPE

SPEED

3 6 9

PROGR

COUNTER

RESET

PAUSE

1 Press MENU to display the main menu. 2 Move the cursor (z) to “PROGRAMME PRESET” with + ◊ or – √ and

press OK. The PROGRAMME PRESET menu appears.

3 Move the cursor (z) to “MANUAL PROGRAMME” with + ◊ or – √ and

press OK. The MANUAL PROGRAMME menu appears.

MANUAL PROGRAMME PRG

SYS I

1 C22 –– –

C24 ––––– ON

C26 ––––– ON

C32 ––––– ON

C36 ––––– ON

C38 –––––ION

LABEL AFT

ndSelect press

–– ON

D – – – – – –

4 Using + ◊ or – √, move the cursor (z) to the programme position you want

to caption and press OK repeatedly until the first element of the “LABEL” position turns red.

5 Select a letter or number with + ◊ or – √ and press OK.

The next element turns red. Select other characters in the same way. For the element you want to leave blank, select “-” and press OK.

If you have made a mistake

Press ? to return to the previous position.

Getting Started

MANUAL PROGRAMME PRG SYS

1 C22 –– –

C24

C26 ––––– ON

C32 ––––– ON

C36 ––––– ON

C38 –––––ION

LABEL AFT MTV

aOKndSelect press

–– ON ––

D – – – – – –

6 After selecting all the characters, press OK repeatedly until the cursor

appears. Now the caption you chose is stored.

7 Repeat steps 4 through 6 to caption other channels. 8 Press MENU to return to the original screen.

TIMER

Manual fine-tuning

Normally, the automatic fine-tuning (AFT) is already working. However, if the picture of a programme is distorted, you can use the manual finetuning function to obtain better picture reception.

SLEEP

VIDEO Plus+

TIMER

ON SCREEN

TIMER REC

ON/OFF

TIMER REC

CLEAR

REC

REPLAY

REW

1 4 7

-/--

QUICK TIMER

INDEX SEARCH

PLAY

STOP

2 5 8 0

TAPE

SPEED

3 6 9 C

PROGR

COUNTER

RESET

PAUSE

1 Press MENU to display the main menu. 2 Move the cursor (z) to “PROGRAMME PRESET” with + ◊ or – √ and press

OK. The PROGRAMME PRESET menu appears.

3 Move the cursor (z) to “MANUAL PROGRAMME” with + ◊ or – √ and

press OK. The MANUAL PROGRAMME menu appears.

4 Using + ◊ or – √, move the cursor (z) to the programme position which

you want to manually fine-tune, and press OK repeatedly until the AFT position turns red.

MANUAL PROGRAMME PRG

SYS I

1 C22 –– –

C24 ––––– ON

C26 ––––– ON

C32 ––––– ON

C36 ––––– ON

C38 –––––ION

LABEL AFT

ndSelect press

–– ON

D – – – – – –

5 Fine-tune the channel while holding down + ◊ or – √ so that you get the

best TV reception. As you press these buttons, the frequency changes from –15 to +15.

To reactivate automatic finetuning (AFT)

Repeat from the beginning and select “ON” in step 5.

MANUAL PROGRAMME PRG

SYS I

1 C22 –– –

C24 ––––– ON

C26 ––––– – 3

C32 ––––– ON

C36 ––––– ON

C38 –––––ION

LABEL AFT

ndSelect press

–– ON

D – – – – – –

6 After fine-tuning, press OK.

The cursor (z) appears. The fine-tuned level is now stored.

7 Repeat steps 4 through 6 to fine-tune other channels. 8 Press MENU to return to the original screen.

Getting Started

TIMER

SLEEP

VIDEO Plus+

TIMER

ON SCREEN

TIMER REC

ON/OFF

TIMER REC

CLEAR

REC

REPLAY

1 4 7

-/--

QUICK TIMER

INDEX SEARCH

2 5 8 0

TAPE

SPEED

3 6 9 C

PROGR

COUNTER

RESET

PAUSE

Tuning in to a channel temporarily

You can tune in to a channel temporarily, even when the channel has not been preset.

1 Press C on the remote control.

The indication “C” (for UHF channels) will appear on the screen.

2 Enter the double digit channel number using the remote control number

buttons (e.g. for channel 24, press 2, then 4). The channel will appear. However, this channel will not be stored in the video TV’s memory.

C24

REW

STOP

PLAY

Note (KV-14V6U, KV-21V6U only)

In order to record a programme received through a Pay-TV decoder, you must preset the channel according to the method on page 8 “Presetting channels manually”, or page 13 “Setting a pay-TV channel,” and then tune in to the channel according to the method on page 17 “Selecting TV programmes”.

Getting Started

Setting a Pay-TV channel (KV-14V6U, KV-21V6U only)

TIMER

SLEEP

VIDEO Plus+

TIMER

ON SCREEN

TIMER REC

ON/OFF

TIMER REC

CLEAR

REC

REPLAY

REW

1 4 7

-/--

QUICK TIMER

INDEX SEARCH

PLAY

STOP

2 5 8 0

TAPE

SPEED

3 6 9

PROGR

COUNTER

RESET

PAUSE

You can watch Pay-TV channels by connecting a Pay-TV decoder to the :1/W 1 connector on the rear of the video TV.

1 Press MENU to display the main menu. 2 Move the cursor (z) to “PROGRAMME PRESET“ with + ◊ or – √ and

press OK. The PROGRAMME PRESET menu appears.

3 Move the cursor (z) to “MANUAL PROGRAMME“ with + ◊ or – √ and

press OK. The MANUAL PROGRAMME menu appears.

4 Move the cursor (z) to the programme position to which you want to set

the pay-TV decoder, and press OK until the D position turns red.

MANUAL PROGRAMME PRG

SYS I

1 C22 –– –

C24 ––––– ON

C26 ––––– ON

C32 ––––– ON

C36 ––––– ON

C38 –––––ION

LABEL AFT

ndSelect press

–– ON

D – – – – – –

5 Press + ◊ or – √ until r appears in the D position and press OK.

Note

While you are recording a program which is being recorded through the Pay-TV decoder, you will not be able to view other programmes through the decoder.

MANUAL PROGRAMME PRG SYS

1 C22 –– –

C24 ––––– ON

C26 ––––– ON

C32 ––––– ON

C36 ––––– ON

C38 –––––ION

LABEL AFT

aOKndSelect press

–– ON

D – –

– – –

6 Press MENU to return to the original screen.

Getting Started

Step 4 —

Manually

TIMER

SLEEP

Setting up VIDEO Plus+

The VIDEO Plus+ function allows you to simplify the task of programming your video TV to make timer recordings. You should coordinate the programme position of each channel with the guide channel (the number that’s assigned to each TV station in advance). To find the guide channel numbers, look in the programme guide for your area that features PlusCodes. See “Guide channels for VIDEO Plus+” on the next page.

VIDEO Plus+

TIMER

ON SCREEN

TIMER REC

ON/OFF

TIMER REC

CLEAR

REC

REPLAY

REW

1 4 7

-/--

QUICK TIMER

INDEX SEARCH

PLAY

STOP

2 5 8 0

TAPE

SPEED

3 6 9 C

PROGR

COUNTER

RESET

PAUSE

Before you begin

• If the u lamp on the video TV is lit in red (indicating that the video TV is

in standby mode), press ;, PROGR +/– or a number button on the remote control.

Setting the guide channels

1 Press MENU to display the main menu.

The main menu appears.

PICTURE CONTROL ON TIMER SET CLOCK SET LANGUAGE PROGRAMME PRESET VCR MODE FUNCTION LOCK

Sape l ec t nd r es s

2 Move the cursor (z) to “PROGRAMME PRESET” with + ◊ or – √ and

press OK. The PROGRAMME PRESET menu appears.

PROGRAMME PRESET

AUTO PROGRAMME MANUAL PROGRAMME SET UP GUIDE CH

If you have made a mistake

Press ? to return to the previous position.

Getting Started

Sapelect nd ress

3 Move the cursor (z) to “SET UP GUIDE CH” with + ◊ or – √ and press

OK. The SET UP GUIDE CH menu appears.

SET UP GUIDE CH PROG

1 C22

C24

C26

3 4

C32 –– –

C36 –– –

C38

ndSelect press

GUIDE CH

––– ––– –––

–––

4 Using + ◊ or – √, move the cursor (z) to the programme position (number

button) to which you want to preset the guide channel, and press OK. The GUIDE CH position turns red.

TIMER

SLEEP

VIDEO Plus+

TIMER

ON SCREEN

TIMER REC

ON/OFF

TIMER REC

CLEAR

REC

REPLAY

REW

1 4 7

-/--

QUICK TIMER

INDEX SEARCH

PLAY

STOP

2 5 8 0

TAPE

SPEED

3 6 9

PROGR

COUNTER

RESET

PAUSE

SET UP GUIDE CH PROG CH

1 C22 2 3 4 5 6

GUIDE CH

––– –––

C24 C26

––– C32 –– – C36 –– –

–––

C38

aOKndSelect press

5 Select the guide channel you want to preset with + ◊ or – √, and press OK.

SET UP GUIDE CH PROG

1 C22

C24

2 3 4

C32 –– –

C36 –– –

C38

ndSelect press

GUIDE CH

–––

99C26

–––

6 Repeat steps 4 and 5 to preset other channels. 7 After you finish presetting, press MENU to return to the original screen.

Guide channels for VIDEO plus+

Guide Station name channel

001 BBC1 002 BBC2 003 ITV 004 CHANNEL 4 005 RTE (IRELAND) 006 NETWORK 2 (IRELAND) 101 SKY ONE 102 SKY NEWS 103 SKY MOVIES 104 THE MOVIE CHANNEL 105 SKY SPORT 106 NICKELODEON

VH-1 GERMANY 107 EUROSPORT 108 GALAVISION 109 MTV EUROPE 110 CHILDERN’S CHANNEL

THE FAMILY CHANNEL 111 SKY MOVIES GOLD 112 BBC WORLD SERVICE 113 RTL 4 114 SUPER SPORT

FILMNET 2

FILMNET + 115 RTL PLUS

INTERNATIONAL 116 SAT 1 117 PREMIERE 118 3 SAT 119 ARD 120 PRO 7 121 TELE 5

Guide Station name channel

122 TELECLUB 123 UK GOLD 124 DISCOVERY

THE LEARNING CHANNEL

125 BRAVO

ADULT CHANNEL 126 CNN 127 EURONEWS 129 QVC 130 UK LIVING 131 RAI 1 132 RAI 2 133 TV5 EUROPE 134 TVE INTERNATIONAL 135 MBC/ARABIC 136 VTM 137 SPORTNET 138 COUNTRY MUSIC TV 139 VIDEO HITS ONE

VH-1 140 SKY SPORT 2 & SOAPS &

TRAVEL 141 TV ASIA 142 LA-5 143 LIVE TV 144 SUPERCHANNEL 145 JAPAN TV 146 SELECT TV 147 MOVIE CHANNEL

FILMNET 1 149 149 TNT

CARTOON NETWORK

Getting Started

Step 5 — Setting the Clock

You need to set the clock in order to use timer recording and quick-timer recording functions.

1 Press MENU to display the main menu.

TIMER

SLEEP

VIDEO Plus+

TIMER

ON SCREEN

TIMER REC

ON/OFF

TIMER REC

CLEAR

1 4 7

-/--

6 9

PROGR

PICTURE CONTROL ON TIMER SET CLOCK SET LANGUAGE PROGRAMME PRESET VCR MODE FUNCTION LOCK

Sape l ec t nd r es s

2 Move the cursor (z) to “CLOCK SET” with + ◊ or – √ and press OK.

The CLOCK SET menu appears.

CLOCK SET

––. ––. –––– ––– –– :––

QUICK

TAPE

REC

REPLAY

REW

TIMER

INDEX SEARCH

STOP

SPEED

PLAY

COUNTER

RESET

PAUSE

If you have made a mistake

Press ? to return to the previous position.

If the clock has stopped and “--/--” is displayed

You have to re-set the clock.

p ress

3 Press OK to start setting the clock.

The day section turns red.

CLOCK SET

1. 1. 19 97 WED 0 : 00

ndSelect press

4 Set the day with + ◊ or – √ and press OK.

The month section turns red.

CLOCK SET

4. 1. 1997 SAT 0 : 00

aOKndSelect press

5 Using + ◊ or – √ and OK, set the month, year, hour and minute in the same

way as in step 4.

CLOCK SET

4. 2. 19 9 7 THU 15 : 3 01

Getting Started

aOKndSelect press

6 After setting the minute, press OK.

The clock starts working.

7 Press MENU to return to the original screen.

+ 36 hidden pages