SONY TR317E Service Manual

CCD-TRV17/TRV37/TRV47/TRV57/

SERVICE MANUAL

Ver 1.4 2004. 05

Photo : CCD-TRV87

B200 MECHANISM

CCD-TR317/TR517

TRV57P/TRV67/TRV87/TRV87P

RMT-708

US Model

CCD-TR517/TRV37/TRV57/TRV67/TRV87

Canadian Model

CCD-TR517/TRV17/TRV37/TRV57/TRV87

E Model

CCD-TR317/TR517/TRV37/

TRV47/TRV57/TRV57P/

TRV67/TRV87/TRV87P

Hong Kong Model

Korea Model

CCD-TR317/TRV47/TRV57/

Brazilian Model

CCD-TR317/TR517/TRV37/TRV67

Argentina Model

CCD-TR517/TRV37/TRV67

Tourist Model

CCD-TRV47/TRV57/TRV67/TRV87

TRV67/TRV87

SPECIFICATIONS

For MECHANISM ADJUSTMENT, refer to the “8mm Video MECHANICAL ADJUSTMENT MANUAL

” (9-973-801-11).

MICROFILM

— Continued on next page —

VIDEO CAMERA RECORDER

CCD-TR317/TR517/TRV17/TRV37/TRV47/TRV57/TRV57P

VIDEO CAMERA RECORDER

CCD-TRV67/TRV87/TRV87P

• SUPPLIED ACCESSORIES

Check that the following accessories are supplied with your camcorder.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer.

1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges.

2. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair . Point them out to the customer and recommend their replacement.

• Abbreviation HK : Hong Kong model

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS P AR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMA TIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

4. Look for parts which, through functioning, show obvious signs

of deterioration. Point them out to the customer and recommend their replacement.

5. Check the B+ voltage to see it is at the values specified.

6. Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270˚C during repairing.

• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering or unsoldering.

— 2 —

Remark

RMT-708: with IC301 of MA-374/375 board.

Hi8: with S-VIDEO jack.

B/W : with VF-129 board.

Color : with VF-141, LB-62 board.

2.5: with PD-117 board.

a: with IC451 of SE-101 board.

a: with IC203 of VC-234 board.

a: with J451 of SE-101 board.

SUPER: with IC203 of VC-234 board.

a: with IC751 of VC-234 board.

a: with VL-29 board.

CCD-

TRV87P

CCD-

TR V87

CCD-

TRV67

CCD-

TRV57P

CCD-

TRV57

CCD-

TRV47

CCD-

TRV37

CCD-

TRV17

US,CND,

E,HK,KR,

US,E,HK,

KR,BR,

AR,JE

US,CND,

E,HK,KR,

US,CND,

E,BR,AR

CND

RMT-708

Hi8

760H

510H

1/4

1/6

aaa

20×

40×

360×

20×

40×

360×

20×

40×

360×

20×

40×

360×

20×

40×

360×

20×

40×

200×

20×

40×

200×

B/W

2.5

aaaaa

SUPER

CF-67

CD-240

EJ-30

PD-117

PJ-100

MA-375

SE-101

VF-129

VL-29

Stereo

Mono

VL-29

20×

40×

80×

B/W

2.5

Mono

CCD-

TR517

US,CND,

E,BR,AR

CCD-

TR317

E,HK,KR,

Model

Destination

Table for difference of function

Remote commander

1/6

20×

510H

8/Hi8

CCD imager

40×

1/6

20×

40×

CCD imager size (inch)

Lens Optical

Digital zoom 1

200×

Color

B/W

200×

Digital zoom 2

EVF

LCD panel (inch)

LCD, Character

Back light, LCD

VTR REC

Steady shot

— 3 —

Mono

DIGITAL EFFECT

Photo mode

Audio system

Headphone jack

Night shot

LASER LINK

Video Light

EJ-29

CF-66

CD-239

CD board

CF board

EJ board

PJ-99

MA-374

PD board

MA board

PJ board

LB-62

VF-141

VF-129

SE board

VF board

LB board

VL board

• Abbreviation

BR : Brazilian model

AR : Argentina model

JE : Tourist model

CND : Canadian model

HK : Hong Kong model

KR : Korea model

TABLE OF CONTENTS

SERVICE NOTE

1. POWER SUPPLY DURING REPAIRS ·····························7

2. TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT) ································································ 7

SELF-DIAGNOSIS FUNCTION

1. Self-diagnosis Function ······················································ 8

2. Self-diagnosis Display························································ 8

3. Service Mode Display ························································ 8

3-1. Display Method ·································································· 8 3-2. Switching of Backup No. ··················································· 8 3-3. End of Display ···································································· 8

4. Self-diagnosis Code Table ·················································· 9

1. GENERAL

Quick Start Guide ······································································ 1-1 Getting Started··········································································· 1-1

Using this manual ··································································1-1 Checking supplied accessories ·············································· 1-2 Step 1: Preparing the power supply·······································1-2

Installing the battery pack ·········································1-2 Charging the battery pack ·········································1-2 Connecting to a wall outlet ·······································1-3

Step 2: Inserting a cassette ····················································1-3

Recording – Basics ···································································· 1-4

Recording a picture································································1-4 Shooting backlit subjects (BACK LIGHT)···························· 1-5 Shooting in the dark (NightShot)··········································· 1-5 Superimposing the date and time on pictures ························ 1-5 Checking the recording – END SEARCH/EDITSEARCH/Rec Review··················1-5

Playback – Basics ······································································ 1-6

Playing back a tape ································································1-6 Viewing the recording on TV ················································1-6

Advanced Recording Operations···············································1-7

Recording a still image on a tape – Tape Photo recording (CCD-TRV87/TRV87P only) ·······1-7 Using the wide mode ·····························································1-8 Using the fader function ························································1-8 Using special effects – Picture effect·····································1-9 Using special effects – Digital effect (CCD-TRV87/TRV87P only) ····················1-9 Using the PROGRAM AE function ·····································1-10 Adjusting the exposure manually ········································1-10 Focusing manually·······························································1-11 Superimposing a title ···························································1-11 Making your own titles ························································1-11 Using the built-in light·························································1-12

Advanced Playback Operations···············································1-12

Playing back a tape with digital effects (CCD-TRV87/TRV87P only) ···········································1-12

Editing ·····················································································1-13

Dubbing a tape ·····································································1-13 Recording video or TV programs (CCD-TRV87/TRV87P only) ···········································1-13

Customizing Y our Camcorder ················································· 1-13

Changing the menu settings·················································1-13 Resetting the date and time··················································1-15

Additional Information ····························································1-15

Usable cassettes and playback modes··································1-15 Changing the lithium battery in your camcorder ·················1-16 Troubleshooting ···································································1-16 Self-diagnosis display ··························································1-17 Warning indicators and messages ········································1-17 Using your camcorder abroad·············································· 1-18 Maintenance information and precautions···························1-18

Quick Reference ······································································1-19

Identifying the parts and controls ········································1-19

2. DISASSEMBLY

2-1. PD-117 BOARD, BACK LIGHT, LIQUID CRYSTAL

DISPLAY PANEL (TRV MODEL) ································2-2 2-2. FRONT PANEL ASSEMBLY, MA-374/375 BOARD···· 2-3 2-3. CABINET (R) BLOCK ASSEMBLY ····························· 2-4 2-4. MECHANISM DECK-1 ················································· 2-5 2-5. EVF BLOCK ASSEMBLY ·············································2-6 2-6. VF-129 BOARD (B/W EVF MODEL)···························2-7 2-7. VF-141, LB-62 BOARDS (COLOR EVF MODEL) ······ 2-8 2-8. LENS DEVICE, CD-239/240 BOARD ·························· 2-9 2-9. DD-134, SE-101 BOARDS···········································2-10 2-10. VC-234, EJ-29/30 BOARDS,

MECHANISM DECK-2 ···············································2-10 2-11. CF-66 BOARD, LIQUID CRYSTAL DISPLAY PANEL

(TR MODEL) ································································ 2-11 2-12. CF-67 BOARD, SPEAKER, PUSH SWITCH

(TRV MODEL) ·····························································2-12 2-13. LCD BLOCK ASSEMBLY, HINGE ASSEMBLY

(TRV MODEL) ·····························································2-12 2-14. HARNESS PROCESSING OF THE HINGE

ASSEMBLY (TRV MODEL) ·······································2-13 2-15. CIRCUIT BOARDS LOCATION·································2-14 2-16. FLEXIBLE BOARDS LOCATION ······························2-15

3. BLOCK DIAGRAMS

3-1. OVERALL BLOCK DIAGRAM (1/2) ··························· 3-3 3-2. OVERALL BLOCK DIAGRAM (2/2) ··························· 3-5 3-3. CAMERA/VIDEO BLOCK DIAGRAM (1/2) ··············· 3-7 3-4. CAMERA/VIDEO BLOCK DIAGRAM (2/2) ··············· 3-9 3-5. VTR/CAMERA CONTROL BLOCK DIAGRAM·······3-11 3-6. SERVO BLOCK DIAGRAM········································3-13 3-7. MODE CONTROL BLOCK DIAGRAM (1/2) ············3-15 3-8. MODE CONTROL BLOCK DIAGRAM (2/2) ············3-17 3-9. AUDIO BLOCK DIAGRAM (1/2) ·······························3-19 3-10. AUDIO BLOCK DIAGRAM (2/2) ·······························3-21 3-11. LCD BLOCK DIAGRAM (TRV MODEL) ··················3-23 3-12. B/W EVF BLOCK DIAGRAM ····································3-25 3-13. COLOR EVF BLOCK DIAGRAM ······························3-27 3-14. POWER BLOCK DIAGRAM (1/2)······························3-29 3-15. POWER BLOCK DIAGRAM (2/2)······························3-31

4. PRINTED WIRING BOARDS AND

SCHEMATIC DIAGRAMS

4-1. FRAME SCHEMATIC DIAGRAM (1/2)·······················4-1

FRAME SCHEMATIC DIAGRAM (2/2)······················· 4-3 4-2. PRINTED WIRING BOARDS AND

SCHEMATIC DIAGRAMS ············································ 4-5

• CD-239/240 (CCD IMAGER) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM ······························4-7

• VC-234 (CAMERA PROCESSOR)(1/13)

SCHEMATIC DIAGRAM ..............................4-9

• VC-234 (Y/C PROCESSOR)(2/13) SCHEMATIC DIAGRAM ····························4-11

• VC-234 (MEMORY)(3/13) SCHEMATIC DIAGRAM ····························4-13

• VC-234 (FOCUS/ZOOM MOTOR DRIVE)(4/13) SCHEMATIC DIAGRAM ····························4-15

• VC-234 (REC/PB AMP)(5/13) SCHEMATIC DIAGRAM ····························4-17

• VC-234 (LINE IN/OUT)(6/13) SCHEMATIC DIAGRAM ····························4-19

• VC-234 (IR TRANSMITTER)(7/13) SCHEMATIC DIAGRAM ····························4-21

— 4 —

• FP-249 (S/T REEL SENSOR, TAPE TOP), FP-356 (TAPE END), FP-355 (TAPE LED)

FLEXIBLE BOARD·····································4-23

• VC-234 (EVR D/A)(8/13)

SCHEMATIC DIAGRAM ····························4-23

• VC-234 (MODE CONTROL)(9/13)

SCHEMATIC DIAGRAM ····························4-25

• VC-234 (SERV O)(10/13)

SCHEMATIC DIAGRAM ····························4-27

• VC-234 (HI CONTROL)(11/13)

SCHEMATIC DIAGRAM ····························4-29

• VC-234 (AUDIO)(12/13)

SCHEMATIC DIAGRAM ····························4-31

• VC-234 (DC IN)(13/13)

SCHEMATIC DIAGRAM ····························4-33

• VC-234 (CAMERA, Y/C PROCESSOR, FOCUS/ZOOM MOTOR DRIVE, REC/PB AMP, LINE IN/OUT, MODE CONTROL, SERVO, HI CONTROL, AUDIO)

PRINTED WIRING BOARD ······················· 4-35

• CF-66 (USER CONTROL)

PRINTED WIRING BOARD ······················· 4-39

• CF-67 (USER CONTROL)

PRINTED WIRING BOARD ······················· 4-43

• CF-66 (USER CONTROL)

SCHEMATIC DIAGRAM ····························4-47

• CF-67 (USER CONTROL)

SCHEMATIC DIAGRAM ····························4-49

• EJ-29/30 (LANC CONNECTOR), SS-9700 (START/STOP SWITCH)

PRINTED WIRING BOARDS·····················4-51

• EJ-29/30 (LANC CONNECTOR)

SCHEMATIC DIAGRAM ····························4-53

• PJ-99/100 (AV IN/OUT)

PRINTED WIRING BOARD ······················· 5-56

• PJ-99/100 (AV IN/OUT)

SCHEMATIC DIAGRAM ····························5-57

• SE-101 (STEADY SHOT)

PRINTED WIRING BOARD ······················· 5-59

• SE-101 (STEADY SHOT)

SCHEMATIC DIAGRAM ····························5-61

• VL-29 (VIDEO LIGHT)

PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM ····························5-63

• MA-374/375 (MIC AMP)

PRINTED WIRING BOARD ······················· 5-65

• MA-374/375 (MIC AMP)(1/2)

SCHEMATIC DIAGRAM ····························5-67

• MA-374/375 (LASER LINK)(2/2)

SCHEMATIC DIAGRAM ····························5-69

• PD-117 (RGB LCD DRIVER, TIMING GENERATOR, CG LCD DRIVER, BACK LIGHT DRIVE)

PRINTED WIRING BOARD ······················· 4-71

• PD-117 (RGB LCD DRIVER, TIMING GENERATOR)(1/2)

SCHEMATIC DIAGRAM ····························4-75

• PD-117 (CG LCD DRIVER, BACK LIGHT DRIVE)(2/2)

SCHEMATIC DIAGRAM ····························4-77

• VF-129 (B/W EVF)

PRINTED WIRING BOARD ······················· 4-80

• VF-129 (B/W EVF)

SCHEMATIC DIAGRAM ····························4-81

• VF-141 (RGB DRIVER, TG)

PRINTED WIRING BOARD ······················· 4-83

• VF-141 (RGB DRIVER, TG)

SCHEMATIC DIAGRAM ····························4-85

• LB-62 (BACK LIGHT) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM ····························4-87

• DD-134 (DC/DC CONVERTER) PRINTED WIRING BOARD ·······················4-89

• DD-134 (DC/DC CONVERTER) SCHEMATIC DIAGRAM ····························4-91

4-3. WAVEFORMS ······························································ 4-93 4-4. MOUNTED LOCATION ··············································4-98

5. ADJUSTMENTS

1. Before starting adjustment···············································5-1 1-1.

Adjusting items when replacing main parts and boards.··· 5-1. CAMERA SECTION ADJUSTMENT ···························5-4 1-1. PREPARATIONS BEFORE ADJUSTMENT

(CAMERA SECTION) ···················································5-4 1-1-1.List of Service Tools ························································5-4 1-1-2.Preparations ·····································································5-5 1-1-3.Precaution ········································································ 5-8

1. Setting the Switch···························································· 5-8

2. Order of Adjustments ······················································5-8

3. Subjects ···········································································5-8 1-2. INITIALIZATION OF D, E, F, 7 PAGE DATA ··············5-9

1. Initializing the D, E, F, 7 Page Data ································5-9

2. Modification of D, E, F, 7 Page Data ······························5-9

3. D Page Table···································································· 5-9

4. F Page table ···································································5-11

5. E Page Table ··································································5-13

6. 7 Page Table···································································5-16 1-3. CAMERA SYSTEM ADJUSTMENTS························5-19

1. HALL Adjustment ·························································5-19

2. Flange Back Adjustment (Using Minipattern Box)·······5-20

3. Flange Back Adjustment

(Using Flange Back Adjustment Chart and Subject

More Than 500m Away) ··············································· 5-21 3-1. Flange Back Adjustment (1)·········································· 5-21 3-2. Flange Back Adjustment (2)·········································· 5-21

4. Flange Back Check························································ 5-22

5. Picture Frame Setting ····················································5-22

6. Color Reproduction Adjustment····································5-23

7. Auto White Balance & LV Standard Data Input ···········5-24

8. Auto White Balance Adjustment ···································5-25

9. White Balance Check ····················································5-26

10. Steady Shot Check

(CCD-TRV57/TRV57P/TRV67/TRV87/TRV87P) ·······5-26 1-4. COLOR ELECTRONIC VIEWFINDER

SYSTEM ADJUSTMENT (CCD-TR517) ····················5-27

1. EVF Initial Data Input ···················································5-27

2. VCO Adjustment (VF-141 board)································· 5-28

3. RGB AMP Adjustment (VC-141 board) ·······················5-28

4. Contrast Adjustment (VF-141 board)····························5-29

5. Backlight Consumption Current Adjustment

(VF-141 board)······························································5-29

6. White Balance Adjustment (VF-141 board)··················5-30 1-5. MONOCHROME ELECTRONIC VIEWFINEDER

SYSTEM ADJUSTMENT

(CCD-TR317/TR V17/TR V37/TR V47/TRV57/

TRV57P/TRV67/TRV87/TRV87P) ·····························5-31 1-5-1.Horizontal Slant Check ·················································5-31 1-5-2.Centering Adjustment ····················································5-31 1-5-3.Focus Adjustment ··························································5-31 1-5-4.Aberration Adjustment ··················································5-32 1-5-5.Horizontal Amplitude Adjustment (VF-129 board) ······ 5-32 1-5-6.Vertical Amplitude Adjustment (VF-129 board) ···········5-33 1-5-7.Brightness Adjustment (VF-129 board) ························5-33 1-5-8.Horizontal Amplitude, V ertical Amplitude,

Focus Check ··································································5-33

5-2

— 5 —

1-6. LCD SYSTEM ADJUSTMENT

(CCD-TRV17/TRV37/TRV47/TRV57/TRV57P/ TRV67/TRV87/TRV87P) ············································5-34

1. LCD Initial Data Input ··················································5-34

2. VCO Adjustment (PD-117 board)·································5-35

3. RGB AMP Adjustment (PD-117 board)························5-35

4. Contrast Adjustment (PD-117 board)····························5-36

5. COM AMP Adjustment (PD-117 board)·······················5-36

6. V-COM Adjustment (PD-117 board) ····························5-37

7. White Balance Adjustment (PD-117 board)··················5-37 5-2. MECHANISM SECTION ADJUSTMENT··················5-38 2-1. OPERA TING WITHOUT CASSETTE ························5-38 2-2. TAPE PATH ADJUSTMENT········································5-38

1. Preparations for Adjustment·········································· 5-38 5-3. VIDEO SECTION ADJUSTMENTS ···························5-39 3-1. PREPARATIONS BEFORE ADJUSTMENTS ············5-39 3-1-1.Equipment to Required··················································5-39 3-1-2.Precautions on Adjusting···············································5-40 3-1-3.Adjusting Connectors ····················································5-40 3-1-4.Connecting the Equipments···········································5-41 3-1-5.Alignment Tape ·····························································5-42 3-1-6.Input/Output Level and Impedance ·······························5-42 3-1-7.Recording Mode (Standard 8/Hi8) switching

(CCD-TRV87/TRV87P) ················································5-42

3-2. SYSTEM CONTROL SYSTEM ADJUSTMENT ········5-43

1. Initialization of D, E, F, 7 Page Data·····························5-43 3-3. SERVO SYSTEM ADJUSTMENTS ····························5-43

1. CAP FG Offset Adjustment (VC-234 board) ················5-43

2. Switching Position Adjustment (VC-234 board)···········5-43 3-4. VIDEO SYSTEM ADJUSTMENTS····························· 5-44

1. 28 MHz Origin Oscillation Adjustment (VC-234 board) ·····························································5-44

2. AFC f

3. Filter f0 Adjustment (VC-234 board)····························· 5-45

4. Y OUT Level Adjustment (VC-234 board) ···················5-45

5. C OUT Level Adjustment (VC-234 board) ···················5-46

6. REC Y Current Adjustment (VC-234 board) ················5-47

7. REC C/AFM Current Adjustment ·································5-48

7-1. Preparations only for the PLAYER model ····················5-48 7-2. REC C Current Check (VC-234 board) ························5-48 7-3. REC AFM Current Adjustment (VC-234 board) ··········5-49 7-4. Processing after completed adjustment only for

3-5. IR TRANSMITTER ADJUSTMENTS

1. IR Video Carrier Frequency Adjustment

2. IR Video Deviation Adjustment (VC-234 board) ·········· 5-50

3. IR Audio Deviation Adjustment (VC-234 board) ·········5-51

3-6. STEREO AUDIO SYSTEM ADJUSTMENT

1. 1.5 MHz Deviation Adjustment (VC-234 board) ··········5-53

2. 1.7 MHz Deviation Adjustment (VC-234 board) ··········5-53

3. BPF f0 Adjustment (VC-234 board) ······························5-54

3-7. MONA URAL A UDIO SYSTEM ADJUSTMENT

1. 1.5 MHz Deviation Adjustment (VC-234 board) ··········5-55

2. BPF Adjustment (VC-234 board)··································5-55

5-4. SERVICE MODE··························································5-56 4-1. ADJUSTMENT REMOTE COMMANDER ················5-56

1. Using the Adjustment Remote Commander··················5-56

2. Precautions Upon Using the Adjustment Remote

4-2. DATA PROCESS···························································5-57 4-3. SERVICE MODE··························································5-58

1. Test Mode Setting ··························································5-58

0 Adjustment (VC-234 board) ·····························5-44

the PLAYER model ······················································· 5-49

(CCD-TR V87/TRV87P) ················································5-50

(VC-234 board) ·····························································5-50

(CCD-TR V87/TR V87P) ················································5-52

(CCD-TR317/TR517/TR V17/TR V37/TRV47/ TRV57/TRV57P/TRV67) ············································5-55

Commander ···································································5-56

2. Emergency Memory Address ········································5-59 2-1. EMG code (Emergency code) ·······································5-59 2-2. MSW codes ···································································5-60

3. Bit Value Discrimination ···············································5-61

4. Input/output selection check··········································5-61

5. LED, LCD (display window) check······························5-61

6. Record of Use check······················································5-62

7. Switch check (1) ····························································5-62

8. Switch check (2) ····························································5-63

9. Headphone jack check (TRV model only) ···················· 5-63

6. REPAIR PARTS LIST

6-1. EXPLODED VIEWS ······················································6-1 6-1-1.FRONT PANEL BLOCK ASSEMBLY AND

BATTERY PANEL BLOCK ASSEMBLY······················6-1

6-1-2.CABINET (R) BLOCK ASSEMBLY (TRV MODEL)

(TRV17/TRV37/TRV47/TRV57/TRV57P/TRV67/ TR V87/TRV87P) ···························································· 6-2

6-1-3.CABINET (R) BLOCK ASSEMBLY (TR MODEL)

(TR317/TR517) ·······························································6-3

6-1-4.LCD BLOCK ASSEMBLY (TRV MODEL)

(TRV17/TRV37/TRV47/TRV57/TRV57P/TRV67/

TR V87/TRV87P) ···························································· 6-4 6-1-5.CABINET (L) BLOCK ASSEMBLY ·····························6-5 6-1-6.B/W EVF BLOCK ASSEMBLY

(TR317/TRV17/TRV37/TRV47/TRV57/TRV57P/

TR V67/TRV87/TRV87P) ···············································6-6 6-1-7.COLOR EVF BLOCK ASSEMBLY (TR517)················6-7 6-1-8.LENS BLOCK ASSEMBLY···········································6-8 6-1-9.CASSETTE COMPARTMENT ASSEMBLY ················6-9 6-1-10. LS CHASSIS BLOCK ASSEMBLY ··························6-10 6-1-11. MECHANISM CHASSIS ASSEMBLY·····················6-11 6-2. ELECTRICAL PARTS LIST ········································6-12

* Parts reference sheet and color reproduction frame are

shown on page 282 and 283.

— 6 —

SERVICE NOTE

1. POWER SUPPLY DURING REPAIRS

In this unit, about 10 seconds after power is supplied (8.4V) to the battery terminal using the service power cord (J-6082-223-A), the power is shut off so that the unit cannot operate. This following two methods are av ailable to prev ent this. Take note of which to use during repairs.

Method 1.

Connect the servicing remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the remote commander switch to the “ADJ” side.

Method 2.

Use the DC IN terminal. (Use the AC power adaptor.)

Battery terminal

DC IN terminal

Battery SIG terminal

2. TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)

1 Refer to 2-2. to remove the front panel block assembly. 2 Refer to 2-3. to remove the cabinet (R) block assembly. 3 Refer to 2-4. to remove the cassette lid assembly. 4 Refer to 2-4. to remove the battery panel block assembly. 5 Refer to 2-4. to remove the cabinet (L) assembly. 6 Disconnect CN974 of VC-234 board. 7 Add +5V from the DC POWER SUPPLY and unload with a

pressing the cassette compartment.

Pull the timing belt in the direction of

arrow the cassette compartment (take care not to damage) to adjust the bending of a tape.

with a pincette while pressing

Press the cassette compartment not to rise the cassette compartment

Battery terminal

Let go your hold the cassette compartment and rise the cassette compartment to take out a cassette.

Timing belt

— 7 —

Pincette

Timing belt

[DC power supply]

(+5V)

Loading motor

Disconnect CN974 of VC-234 board.

Adjust the bending of a tape

SELF-DIAGNOSIS FUNCTION

1. Self-diagnosis Function

When problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the viewfinder or Display window what to do. This function consists of two display; selfdiagnosis display and service mode display . Details of the self-diagnosis functions are provided in the Instruction manual.

Viewfinder Display window

C : 3 1 : 1 1

Repaired by:

C : Corrected by customer H : Corrected by dealer E : Corrected by service

engineer

Blinks at 3.2Hz

Indicates the appropriate step to be taken. E.g.

31 ....Reload the tape.

32 ....Turn on power again.

3 1

Block

1 1

C : 3 1 : 11

Refer to page 9 and 10. Self-diagnosis Code Table.

2. Self-diagnosis Display

When problems occur while the unit is operating, the counter of the viewfinder or Display window shows a 4-digit display consisting of an alphabet and numbers, which blinks at 3.2 Hz. This 5-character display indicates the “repaired by:”, “block” in which the problem occurred, and “detailed code” of the problem.

Display window

Detailed Code

3. Service Mode Display

The service mode display shows up to six self-diagnosis codes shown in the past.

3-1. Display Method

While pressing the “STOP” key, set the switch from OFF to “VTR or PLAYER”, and continue pressing the “STOP” key for 5 seconds continuously. The service mode will be displayed, and the counter will show the backup No. and the 5-character self-diagnosis codes.

Viewfinder

[3] C : 3 1 : 1 1

Lights up

[3]

Backup No.

Order of previous errors

C : 3 1 : 1 1

Self-diagnosis Codes

3-2. Switching of Backup No.

By rotating the control dial, past self-diagnosis codes will be shown in order. The backup No. in the [] indicates the order in which the problem occurred. (If the number of problems which occurred is less than 6, only the number of problems which occurred will be shown.) [1] : Occurred first time [4] : Occurred fourth time [2] : Occurred second time [5] : Occurred fifth time [3] : Occurred third time [6] : Occurred the last time

Display window

3 C : 3 1 : 11

Control dial

3-3. End of Display

Turning OFF the power supply will end the service mode display.

Note: The “self-diagnosis display” data will be backed up by the coin-type lithium battery (CF-66/67 board BH001). When

this coin-type lithium battery is disconnected, the “self-diagnosis display” data will be lost by initialization.

— 8 —

4. Self-diagnosis Code Table

Self-diagnosis Code

Repaired by:

C C C

C C

C C C C C C C C C C

Block

Function

04 21 22

31 31

31 31 31 31 31 31 31 31 31 31

Detailed

Code

00 00 00

11 20

21 22 23 30 31 40 41 42 43 44

Symptom/State

Non-standard battery is used. Condensation. Video head is dirty. LOAD direction. Loading does not

complete within specified time UNLOAD direction. Loading does not

complete within specified time T reel side tape slacking when unloading S reel

side tape slacking when unloading T reel fault. S reel fault. FG fault when starting capstan. FG fault during normal capstan operations. FG fault when starting drum. PG fault when starting drum. FG fault during normal drum operations. PG fault during normal drum operations. Phase fault during normal drum operations. LOAD direction loading motor time-

out. UNLOAD direction loading motor

time-out. T reel side tape slacking when

unloading. S reel side tape slacking when

unloading. T reel fault.

S reel fault.

FG fault when starting capstan. FG fault during normal capstan

operations. FG fault when starting drum.

PG fault when starting drum. FG fault during normal drum

operations. PG fault during normal drum

operations. Phase fault during normal drum

operations.

Correction

Use the InfoLITHIUM battery. Remove the cassette, and insert it again after one hour. Clean with the optional cleaning cassette.

Load the tape again, and perform operations from the beginning.

Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Remove the battery or power cable, connect, and perform

operations from the beginning. Remove the battery or power cable, connect, and perform

operations from the beginning.

— 9 —

Self-diagnosis Code

Function

Repaired by:

Block

Detailed

Code

Symptom/State

Difficult to adjust focus (Cannot initialize focus.)

Zoom operations fault (Cannot initialize zoom lens.)

Handshake correction function does not work well. (With pitch angular velocity sensor output stopped.)

Handshake correction function does not work well. (With yaw angular velocity sensor output stopped.)

Correction

Inspect the lens block focus reset sensor (Pin qs of CN551 of VC- 234 board) when focusing is performed when the control dial is rotated in the focus manual mode and the focus motor drive circuit (IC551 of VC-234 board) when the focusing is not performed.

Note: Use the remote commander RM-95 only for the model without the

focus dial.

Inspect the lens block zoom reset sensor (Pin qf of CN551 of VC234 board) when zooming is performed when the zoom lens is operated and the zoom motor drive circuit (IC551 of VC-234 board) when zooming is not performed.

Inspect pitch angular velocity sensor (SE451 of SE-101 board) peripheral circuits.

Inspect yaw angular velocity sensor (SE452 of SE-101 board) peripheral circuits.

— 10 —