Sony SSCT-1000-D, SSCT-999-D, SSGN-1000-D, SSGN-1000-S, SSGN-999-D Service manual
...
SS-CT999D/CT1000D/GN999D/GN999S/GN1000D/
GN1000S/RSX999D/RSX1000D/WGV999D/WGV1000D
SERVICE MANUAL
E Model
Ver. 1.0 2006. 05
Photo : SS-RSX999D Photo : SS-GN999D Photo : SS-RSX1000D Photo : SS-WGV999D Photo : SS-WGV1000D
COMPONENT MODEL NAME
System name
Destination EXCEPT E2, E51, MX
FRONT SP EAKERS
SURROUND SPEAKERS SS-RSX999D
CENTER SPEAKER SS-CT999D
SUB WOOFER
DVD PLAYER DECK RECEIVER
MHC-GN999D
E2, E51, MX
SS-GN999D
SS-WGV999D
HCD-GN999D
MHC-GN999DS
SS-GN999S
Destination
FRONT SP EAKERS
SURROUND SPEAKERS
CENTER SPEAKER
SUB WOOFER
DVD PLAYER DECK
RECEIVER SYSTEM
•Abbreviation
E2 : 120 V AC Area in E model
E51 : Chilean and Peruvian model
MX : Mexican model
MHC-GN1000DSystem name
E2
SS-GN1000DP SS-GN1000SP
HCR-GN1000D
SS-GN1000D SS-GN1000S
SS-RSX1000D SS-RSX1000D
SS-CT1000D
SS-WGV1000D
HCD-GN1000D
• JIG
When disassembling the set, use the following jig (for
speaker removal).
Part No.: J-2501-238-A JIG FOR SPEAKER REMOVAL
EXCEPT E2
CENTER SPEAKER/FRONT SPEAKERS/
SURROUND SPEAKERS/SUB WOOFER
9-887-255-01
2006E02-1
© 2006.05
Sony Corporation
Home Audio Division
Published by Sony Techno Create Corporation
SS-CT999D/CT1000D/GN999D/GN999S/GN1000D/GN1000S/RSX999D/RSX1000D/WGV999D/WGV1000D
SPECIFICATIONS
For MHC-GN999D/MHC-GN999DS
• Front speaker (SS-GN999D/SS-GN999S)
Speaker system 2-way, 2-unit, bass-reflex type,
magnetically shielded
Speaker units
Woofer: 20 cm, cone type
Tweeter: 2.5 cm, horn type
Nominal impedance 6 ohms
Dimensions (w/h/d) Approx. 281 x 417 x 310.5 mm
Mass Approx. 7.2 kg net per speaker
• Surround speaker (SS-RSX999D)
Speaker system Full range, 2-unit, bass-reflex
type
Speaker units
Full range: 8 cm, cone type x 2
Nominal impedance 16 ohms
Dimensions (w/h/d) Approx. 268 x 107 x 117 mm
Mass Approx. 1.4 kg net per speaker
• Center speaker (SS-CT999D)
Speaker system Full range, 2-unit, bass-reflex
type, magnetically shielded
Speaker units
Full range: 8 cm, cone type x 2
Nominal impedance 16 ohms
Dimensions (w/h/d) Approx. 268 x 107 x 117 mm
Mass Approx. 1.6 kg
• Sub woofer (SS-WGV999D)
Speaker system 1-way, 1-unit, bass-reflex type,
magnetically shielded
Speaker units
Woofer: 20 cm, cone type
Nominal Impedance 6 ohms
Dimensions (w/h/d) Approx. 262 x 327 x 370 mm
Mass Approx. 6.6 kg
For MHC-GN1000D
• Front speaker (SS-GN1000D (Latin American models only)/
SS-GN1000S (Other models))
Speaker system 2-way, 2-unit, bass-reflex type,
magnetically shielded
Speaker units
Woofer: 20 cm, cone type
Tweeter: 2.5 cm, horn type
Nominal impedance 6 ohms
Dimensions (w/h/d) Approx. 281 x 417 x 310.5 mm
Mass Approx. 7.2 kg net per speaker
• Surround speaker (SS-RSX1000D)
Speaker system 2-way, 2-units, bass-reflex type
Speaker units
Woofer: 10 cm, cone type
Tweeter: 5 cm, horn type
Nominal impedance 6 ohms
Dimensions (w/h/d) Approx. 176 x 362 x 215 mm
Mass Approx. 2.9 kg net per speaker
• Center Speaker (SS-CT1000D)
Speaker system Full range, 2-unit,
bass-reflex type,
magnetically shielded
Speaker units
Full range: 8 cm, cone type x 2
Nominal Impedance 6 ohms
Dimensions (w/h/d) Approx. 268 x 107 x 117 mm
Mass Approx. 1.6 kg
• Subwoofer (SS-WGV1000D)
Subwoofer system 1-way, 1-unit, bass-reflex type,
magnetically shielded
Speaker units
Subwoofer: 20 cm, cone type
Nominal impedance 8 ohms
Dimensions (w/h/d) Approx. 281 × 362 × 338.5 mm
Mass Approx. 6.8 kg
Design and specifications are subject to change without notice.
2
SS-CT999D/CT1000D/GN999D/GN999S/GN1000D/GN1000S/RSX999D/RSX1000D/WGV999D/WGV1000D
B
These are omitted.
CE
Q
SECTION 1
DIAGRAMS
1-1. PRINTED WIRING BOARD (SS-WGV1000D)
1
HCD-GN1000D
A
BOARDSWPANEL
CN1400
Q1400
JR1400
E
1
R1406
D1400
S1400
2
4
R1405
SUBWOOFER
ON/OFF
B
C1401
JR1402
: Uses unleaded solder.
3
C1400
C
D
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
• Strong viscosity
• Usable with ordinary solder
R1401
R1402
R1403
R1404
SW1400
SUBWOOFER
LEVEL
1-868-600-
: LEAD FREE MARK
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
11
(11)
Note on Printed Wiring Boards:
• X : parts extracted from the component side.
• : Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
• Indication of transistor.
3
SS-CT999D/CT1000D/GN999D/GN999S/GN1000D/GN1000S/RSX999D/RSX1000D/WGV999D/WGV1000D
1-2. SCHEMATIC DIAGRAM (SS-WGV1000D)
D1400
SELU5420E
GREEN
SUBWOOFER
HCD-GN1000D
CN1400
4P
R1406
R1405
1k
SUBWOOFER
ON/OFF
1k
S1400
ON/OFF
JR1402
0
Q1400
2SC2712
LED DRIVE
C1401
1
50V
SW1400
SUBWOOFER
LEVEL
R1401
2.2k
R1404
68k
R1402
6.8k
R1403
22k
C1400
10
50V
JR1400
0
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. (p: pF) 50 WV or
less are not indicated except for electrolytics and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise specified.
• C : panel designation.
4
• A : B+ Line.
•Voltages are dc with respect to ground in service mode.
no mark : POWER ON
•Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
Loading...