Sony SRS-XB2 Users guide
4-587-045-41(1)
Personal Audio System
Reference Guide
SRS-XB2
©2016 Sony Corporation
Printed in China
http://www.sony.net/
English Personal Audio System
Before operating the system, please read this guide thoroughly and retain it for future reference.
WARNING
To reduce the risk of fire, do not cover the ventilation opening of the appliance with newspapers,
tablecloths, curtains, etc.
Do not expose the appliance to naked flame sources (for example, lighted candles).
To reduce the risk of fire or electric shock, do not expose the USB AC adaptor to dripping or
splashing, and do not place objects filled with liquids, such as vases, on the USB AC adaptor.
Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.
Do not expose the batteries (battery pack or batteries installed) to excessive heat such as sunshine,
fire or the like for a long time.
As the main plug of the USB AC adaptor is used to disconnect the USB AC adaptor from the mains,
connect it to an easily accessible AC outlet. Should you notice an abnormality in it, disconnect it
from AC outlet immediately.
The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall
outlet, even if the unit itself has been turned off.
The validity of the CE marking is restricted to only those countries where it is legally enforced,
mainly in the countries EEA (European Economic Area).
Disposal of Old Electrical & Electronic Equipment (Applicable in the
European Union and other European countries with separate collection
systems)
Precautions
Note when using with a mobile phone
For details on operation of your mobile phone when receiving a telephone call while transmitting
the sound using the BLUETOOTH connection, refer to the operating instructions supplied with the
mobile phone.
On safety
The nameplate and important information concerning safety are located on the bottom exterior
of the main unit and on the surface of the USB AC adaptor.
Before operating the system, be sure that the operating voltage of the system is identical with
that of your local power supply.
Where purchased Operating voltage
All countries/regions 100 V – 240 V AC, 50 Hz/60 Hz
Notes on the USB AC adaptor
When connecting or disconnecting the USB AC adaptor, turn off the system beforehand.
Otherwise, it may cause malfunction.
Use only the supplied USB AC adaptor and micro-USB cable. To avoid damaging the system, do
not use any other USB AC adaptor.
Polarity of the USB port of the
Plug the USB AC adaptor into a nearby wall outlet (mains). In the case of a problem, unplug it
from the wall outlet (mains) immediately.
Do not install the USB AC adaptor in a confined space, such as a bookcase or built-in cabinet.
To reduce the risk of fire or electric shock, do not expose the USB AC adaptor to dripping or
splashing, and do not place objects filled with liquids, such as vases, on the USB AC adaptor.
On placement
Do not set the speaker in an inclined position.
Do not leave the system in a location near heat sources, or in a place subject to direct sunlight,
excessive dust, moisture, rain or mechanical shock.
On operation
Do not insert any small objects, etc., into the jacks or ventilation hole on the rear of the system.
The system may short out or malfunction.
On cleaning
Do not use alcohol, benzine, or thinner to clean the cabinet.
Others
Two units are required when using the Speaker Add function. Only the SBC codec is supported
while using the Speaker Add function.
If you have any questions or problems concerning this system that are not covered in this
manual, please consult your nearest Sony dealer.
On Copyrights
LDAC™ and LDAC logo are trademarks of Sony Corporation.
The BLUETOOTH® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such
marks by Sony Corporation is under license.
The N Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States and in
other countries.
Other trademarks and trade names are those of their respective owners.
USB AC adaptor
Notes on water resistant feature
(Read before using the system)
Water resistant performance of the system
This system has a water resistant specification*1,*2 of IPX5*3 as specified in “Degrees of protection
against ingress of water” of the IEC60529 “Ingress Protection Rating (IP Code).” However, this
system is not completely water-tight.
Do not drop the system into hot water in a bathtub or purposely use it in water. Depending on
usage, water entering the system may cause fire, electric shock or malfunction.
Use the system with full understanding of the following.
Liquids that the water resistant performance specifications apply to
Applicable : fresh water, tap water, sweat
Not applicable : liquids other than the above (soapy water, water with detergent or
1
Requires that the cap is fastened securely.
*
2
The supplied accessories are not water resistant.
*
3
IPX5 (Degree of protection against jets of water): The system has been tested and found to
*
remain functional after exposure to direct jet streams of water using a nozzle of 6.3 mm internal
diameter from any direction where approximately 12.5 L/ min of water is applied for a period of
more than 3 minutes from a distance of about 3 meters.
The water resistant performance of the system is based on our measurements under the
conditions herein described. Note that malfunctions as a result of water immersion caused by
misuse by the customer are not covered by the warranty.
To avoid the deterioration of the water resistant performance
Check the following and use the system correctly.
Do not use or leave the system in an extremely hot or cold environment (temperature outside the
range of 5 °C – 35 °C). If the system is used or left in outside the above range, the system may
automatically stop to protect internal circuitry.
Be careful not to drop the system or subject it to mechanical shock. Deformation or damage may
cause deterioration of the water resistant performance.
Do not use the system in a location where large amount of water or hot water may splash on it.
The system does not have a design that is resistant to water pressure. Use of the system in the
above location may cause a malfunction.
Do not pour high-temperature water or blow hot air from a hair dryer or any other appliance on
the system directly. Also, never use the system in high temperature locations such as in saunas or
near a stove.
Handle the cap with care. The cap plays a very important role in maintenance of the water
resistant performance. When using the system, make sure that the cap is closed completely.
When closing the cap, be careful not to allow foreign objects inside. If the cap is not closed
completely the water resistant performance may deteriorate and may cause a malfunction of the
system as a result of water entering the system.
How to care for the system when wet
If the system gets wet, first remove the water from the system, and then wipe off the moisture on
the system using a soft, dry cloth. Especially in cold regions, leaving moisture on its surface may
cause the system to freeze and malfunction. Be sure to wipe off the moisture after using the
system.
Put the system on towel or dry cloth. Then leave it at room temperature and dry the system until no
moisture remains.
bath agents, shampoo, hot spring water, hot water, pool water,
seawater, etc.)
Cap
Specifications
Speaker section
Speaker system Approx. 42 mm dia. × 2
Enclosure type Passive radiator model
BLUETOOTH
Communication System
Output BLUETOOTH Specification Power Class 2
Maximum communication range
Frequency band 2.4 GHz band (2.4000 GHz - 2.4835 GHz)
Modulation method FHSS
Compatible BLUETOOTH Profiles*
Supported Codec*
Transmission range (A2DP)
1
The actual range will vary depending on factors such as obstacles between devices, magnetic
*
fields around a microwave oven, static electricity, reception sensitivity, aerial’s performance,
operating system, software application, etc.
2
BLUETOOTH standard profiles indicate the purpose of BLUETOOTH communication between
*
devices.
3
Codec: Audio signal compression and conversion format
*
4
Subband Codec
*
5
Advanced Audio Coding
*
6
LDAC is an audio coding technology developed by Sony that enables the transmission of
*
High-Resolution (Hi-Res) Audio content, even over a BLUETOOTH connection. Unlike other
BLUETOOTH compatible coding technologies such as SBC, it operates without any downconversion of the Hi-Res Audio content*
than those other technologies to be transmitted over a BLUETOOTH wireless network with
unprecedented sound quality, by means of efficient coding and optimized packetization.
7
Excluding DSD format contents.
*
8
In comparison with SBC (Subband Coding) when the bitrate of 990kbps (96/48 kHz) or 909kbps
*
(88.2/44.1 kHz) is selected.
Microphone
Type Electret condenser
Directional characteristic
Effective frequency range
General
Input AUDIO IN jack (ø 3.5 mm stereo mini jack)
Power DC 5 V (using the supplied USB AC adaptor connected to AC 100 V - 240V,
Usage life of lithium-ion battery (using the BLUETOOTH connection)
Dimensions (including projecting parts and controls)
Mass Approx. 480 g including battery
Supplied accessories USB AC adaptor (1)
*9 When the specified music source is used and the volume level of the unit is set to 10.
If the volume level of the unit is set to maximum, the usage life will be approx. 3 hours.
Time may vary, depending on the temperature or conditions of use.
10
The item is not included in some countries/regions.
*
Design and specifications are subject to change without notice.
BLUETOOTH Specification version 3.0
Line of sight approx. 10 m*
2
A2DP (Advanced Audio Distribution Profile)
AVRCP (Audio Video Remote Control Profile)
HSP (Headset Profile)
HFP (Hands-free Profile)
3
SBC*4, AAC*5, LDAC*
20 Hz - 20,000 Hz (Sampling frequency 44.1 kHz)
Omni directional
100 Hz - 7,000 Hz
50Hz/60 Hz power supply) or, using built-in lithium-ion battery
Approx. 12 hours*
Approx. 191 mm × 62 mm × 65 mm (w/h/d)
Micro-USB cable (1)
Operating Instructions (1)
Reference Guide (this document) (1)
Warranty card (1)*
1
6
7
, and allows approximately three times more data*8
9
10
Loading...