For proper use of the SO-03D, read this manual carefully before and while you use the SO-03D.
Before using the terminal
●
SO-03D supports W-CDMA, GSM/GPRS and Wireless LAN Systems.
●
Because a terminal operates using radio frequencies, it cannot be used inside a tunnel, underground, in a
building or other locations where radio waves do not reach the terminal, in locations with weak radio wave
condition, or outside of the FOMA's service area. The services may not be available on high upper floors of
high-rise apartments or buildings, even if you can see no obstructions around you. On occasion, your calls
may become disconnected even in areas with strong radio wave condition, even if you are not moving, or
even if there are 4-antenna marks in the terminal's display.
●
Note that because the terminal operates on radio frequencies, your calls are at risk of being intercepted by
the third party. However, the W-CDMA, GSM/GPRS system automatically scrambles all calls through a
private call feature. Therefore, even if third party successfully intercepts your call, they will only hear noise.
●
The terminal operates on radio frequencies by converting voice into digital signals. If the caller moves into
an area of adverse radio wave condition, the digital signal may not be restored accurately, and the voice
received in the call may differ slightly from the actual voice.
●
Note down the information saved in the terminal in a separate note and keep it safely. Even if the data
may be lost as a result of malfunction, repair, change, or other handling of the terminal, under no
condition will DOCOMO be held liable for any lost data saved in the terminal.
●
You are recommended to save important data to microSD card.
●
As with PCs, some user-installed applications may disrupt the stability of the terminal performance, or
unexpectedly transmit information via the Internet causing improper use of your location information as
well as personal information recorded on the terminal. Therefore, verify the supplier and operating
conditions of the applications to be used before using them.
●
This terminal has FOMA Plus-Area and FOMA HIGH-SPEED Area support.
●
Descriptions in this manual are fore the terminal with a DOCOMO's UIM inserted.
SIM unlock
This terminal supports SIM unlock. If you release SIM lock, you can use SIM by a carrier other than NTT
DOCOMO.
●
The SIM unlock service is provided at a docomo Shop.
●
A SIM unlock charge is separately required.
●
If you use a SIM other than by DOCOMO, available services and functions will be limited. DOCOMO is not
liable to any failures or malfunctions.
●
For details of SIM unlock, refer to NTT DOCOMO website.
Supplied accessories
Supplied accessories
・
SO-03D (with warranty)
・
クイックスタートガイド
(In Japanese only)
クイック
スタート
ガイド
(Quick Start Guide)
・
AC Adapter Cable SO03 (with warranty)
<AC adapter><microUSB cable>
・
Desktop Holder SO12 (with warranty)
・
microSD card (2GB)* (Sample)
(with manual)
* Inserted in the terminal when purchased.
・
Stereo Headset with Microphone (Sample)
(with manual)
・
のご利用にあたっての注意事項
SO-03D
安全上/取り扱い上のご注意
(Notes on usage Safety/Handling
precautions) (In Japanese only)
For details on optional devices, see "Optional
and related devices" (P.243).
1
About manuals of SO-03D
In addition to this manual, the operations of
SO-03D are described in "
イド
(Quick Start Guide)" (in Japanese only)
and "Instruction Manual" application of the
terminal.
クイックスタートガ
❖
Note
・
For downloading or updating the application, a high
packet communication charge will be applied
because of a large amount data communication. For
this reason, subscription of packet flat-rate service is
highly recommended.
* If you use Wi-Fi function to download, packet
communication charges are not applied.
クイックスタートガイド
"
(Quick
Start Guide)" (Supplied
accessories)
The initial operations and settings after
purchasing the terminal, screen view
contents and operations of main function are
explained. (In Japanese only)
"Instruction Manual"
(Application of the terminal)
Similarly to this manual, operations and
settings of each function are explained.
To use "Instruction Manual" application, from
the Home screen,
Manual]. For the first time using, download
and install it according to the onscreen
instructions. You can use the application as
an electronic book. You can also shift to
actual operations by tapping the description
in the contents or view reference contents.
u
Tap [ Inst ruc tion
"Instruction Manual" (PDF file)
Operations and settings of each function are
explained.
It can be downloaded from NTT DOCOMO
website.
http://www.nttdocomo.co.jp/english/
support/trouble/manual/download/
index.html
* You can download the latest information of
クイックスタートガイド
"
(in Japanese only). The URL and contents are
subject to change without prior notice.
❖
Note
・
Reproduction or reprint of all or part of this manual
without prior permission is prohibited.
・
Important information for SO-03D is posted in the
following website. Be sure to check before using.
http://www.sonyericsson.co.jp/support/
use_support/product/so-03d/
(Quick Start Guide)"
2
Operation descriptions
In this manual, each key operation is
described with
m, k
the icons or function items on the touch
panel are described as follows.
DescriptionOperation
From the Home
screen, tap t
and tap [Settings].
Tap
[Settings]
& time]
date].
Tap to zoom
in or out on a map.
Touch and hold
icon.
❖
Information
・
In this manual, the instructions are described with
the default Home screen. If you set the other
application to the home screen, the operations may
differ from the descriptions.
・
Display examples and illustrations used in this
manual are just images for explanations and may be
different from actual ones.
・
In this manual, the easier procedure is described for
the functions and settings which have multiple
operating procedures.
p, x, y, t
. And selection operations of
From the Home screen, tap
t
(Menu) key and tap
"Settings" on the screen.
Tap "Settings" displayed on the
u
[Date
u
screen, and then tap "Date &
[Set
time" on the next screen and
"Set date" on the following
screen in order.
Tap dis playe d on the
screen to zoom in or out the
map.
Keep touching the icon longer
(1-2 seconds).
・
Please note that "SO-03D" is called "the terminal" in
this manual.
・
In this manual, explanations for "docomo" as Home
,
application are provided. To switch the Home
applications, see "Learning Home screen" (P.66).
The terminal does not support i-mode sites
(programs) or i-
・
The terminal automatically performs
communication for synchronizing data,
checking the latest software version, maintain
connection with the server, etc. If you
transmit a large amount of data such as
downloading applications or watching
movie, a packet communication charge
becomes high. Subscription of packet flatrate service is highly recommended.
・
Public mode (Driving mode) is not supported.
・
Setting the phone to silent mode does not
mute playback sound of video or music,
alarm, etc.
・
The names of the operators are displayed on
key lock canceling screen (P.39).
・
Your phone number (own number) can be
checked as follows:
From the Home screen, tap
[Settings]
・
The software version of your terminal can be
checked as follows:
From the Home screen, tap
[Settings]
D
ppli.
u
[About phone]u[Status].
u
[About phone].
t
t
and tap
and tap
・
You can perform software update by
downloading an update file with a PC via
Internet and connecting the PC to the
terminal. For details, see "Connecting to a PC
and updating" (P.254).
・
By some software updates, the operating
system (OS) may be version-upgraded for
improving the terminal quality. For this
reason, you always need to use the latest OS
version. And some applications that used in
the previous OS version may not be available
or some unintended bugs may occur.
・
When using the terminal inserting some UIM
(FOMA card) (green), voice calls and packet
communication may not be available in some
overseas networks. For using overseas, please
visit a docomo Shop near you. DOCOMO
exchanges UIM (FOMA card) (green) for UIM
free of charge.
・
Set the screen lock to ensure the security of
your terminal for its loss. For details, see
"Screen lock" (P.127).
・
If your terminal is lost, change your each
account password to invalidate
authentication using a PC to prevent other
persons from using Google services such as
Google Talk, Gmail, Android Market, etc.,
Facebook, Twitter and mixi.
・
The terminal supports only sp-mode, mopera
U and Business mopera Internet. Other
providers are not supported.
Content s/Precautio ns
7
・
Battery is built into the terminal and cannot
be replaced by yourself.
・
To use tethering, subscription of sp-mode is
required.
・
Packet communication charge when using
tethering varies depending on the charging
plan you use. Subscription of packet flat-rate
service is highly recommended.
・
For details on usage charge, etc., refer to http:/
/www.nttdocomo.co.jp/ .
Content s/Precautio ns
8
Safety Precautions (Always
follow these directions)
■
For safe and proper use of the terminal, please
read the "Safety Precautions" prior to use.
Keep the Manual in a safe place for future
reference.
■
ALWAYS observe the safety precautions since
they intend to prevent personal injury or
property damage.
■
The following symbols indicate the different
levels of injury or damage that may result if
the guidelines are not observed and the
terminal is used improperly.
Failure to
observe these
guidelines may
DANGER
WARNING
CAUTION
immediately
result in death
or serious
injury.
Failure to
observe these
guidelines may
result in death
or serious
injury.
Failure to
observe these
guidelines may
result in injury
and property
damage.
■
The following symbols indicate specific
directions.
Indicates prohibited actions.
Don’t
Indicates not to disassemble.
No disassembly
Indicates not to handle with wet
hands.
No wet hands
Indicates not to use where it could
get wet.
No liquids
Indicates compulsory actions in
accordance with instructions.
Do
Indicates to remove the power plug
from the outlet.
Unplug
■
"Safety Precautions" are described in the
following categories:
1. Handling the terminal, AC Adapter
cable, Desktop Holder and UIM
(general)
DANGER
Do not use, store or leave the equipment in
hot places (e.g. by the fire, near a heater,
Don’t
under a kotatsu, in direct sunlight, in a car in
the hot sun). (including the event that you
ware the equipment in the pocket of your
clothes, etc.)
Doing so may cause fire, burns or injury.
Do not place equipment inside cooking
appliance such as a microwave oven or high-
Don’t
pressure containers.
Doing so may cause fire, burns, injury or
electric shock.
Do not disassemble or modify the
equipment.
No disassembly
Doing so may cause fire, burns, injury or
electric shock.
Do not let the equipment get wet with
water, drinking water, urine of pet animals,
No liquids
etc.
Doing so may cause fire, burns, injury or
electric shock.
For waterproofness
Use the AC adapter cable for the terminal
specified by DOCOMO.
Do
Failure to do so may cause fire, burns, injury or
electric shock.
→
P.24 "Waterproofness"
WARNING
Do not subject the equipment to excessive
force or throw it.
Don’t
Doing so may cause fire, burns, injury or
electric shock.
Do not allow the microUSB connecting jack,
headset connecting jack or HDMI
Don’t
connecting jack to come in contact with
conducting foreign substances (a piece of
metal, pencil lead, etc.). Never allow these
objects to get into the connecting jack.
Doing so may cause fire, burns, injury or
electric shock.
Do not cover or wrap the equipment with a
cloth or bedding in use or while charging.
Don’t
Doing so may cause fire or burns.
Power off the terminal before you step into a
place where flammable gas can leak, such as
Do
gas stations. Stop charging if you charge the
battery.
Gas may catch fire.
When using Osaifu-Keitai in a place such as a
gas station, turn OFF the terminal before using
it.
(When Osaifu-Keitai lock is activated,
deactivate it before turning OFF the terminal.)
Content s/Precautio ns
10
If you notice anything unusual about the
equipment such as an unusual odor,
Do
overheating, discoloration or deformation
during operation, charging or storage,
immediately perform the following
measures.
・
Remove the power plug from the power
outlet.
・
Power off the terminal.
Failure to do so may cause fire, burns, injury or
electric shock.
CAUTION
Do not place on an unstable or inclined
platform.
Don’t
Doing so may cause the device to fall and
cause injury.
Do not keep in a place that is very humid,
dusty, or subject to high temperature.
Don’t
Doing so may cause fire, burns or electric
shock.
If children use the terminal, parents or
guardians should give them the proper
Do
instructions for use. Make sure that they use
the terminal as instructed.
Failure to do so may cause injury.
Keep the equipment out of the reach of
babies and infants.
Do
Failure to do so may cause accidental
swallowing or injury.
Be careful especially when you use the
terminal while it has been continuously
Do
connected to the AC adapter cable for a long
period of time.
If you play a game or watch 1Seg for a long
time while charging, the temperature of the
terminal and AC adapter cable may rise.
If you are directly in contact with hot parts for
a long period of time, it may cause your skin to
become red, itchy, or develop a rash
depending on your physical condition and
also it may cause low-temperature burn.
Observe the followings for 3D image
function.
Do
・
Do not view 3D images shot by the terminal
with a 3D compatible monitor for a long
time. Doing so may cause unpleasant
symptom such as eyestrain, fatigue, feeling
ill, etc.
・
For viewing 3D images, you are
recommended to take a proper break.
Necessary break length or frequency varies
by individual. Judge for yourself.
・
When you experience unpleasant symptom,
stop viewing 3D images until you get healed
up and seek the advice of a doctor if
necessary. Also refer to the manuals come
with the device for connecting to the
terminal or software.
・
Vision of child (especially younger than 7
years) is during development. Before a child
views 3D images, seek the advise of a doctor
such as pediatrics or ophthalmol ogist. Adults
should supervise a child for the above
precautions.
Content s/Precautio ns
11
2. Handling the terminal
■
The internal battery for the terminal is as
follows.
DisplayType of Battery
Li-ion 00Lithium Ion Battery
DANGER
Do not throw the terminal into fire.
Doing so may cause internal battery to ignite,
Don’t
explode, overheat or leak.
Do not stick a nail into the terminal, hit it
with a hammer, or step on it.
Don’t
Doing so may cause internal battery to ignite,
explode, overheat or leak.
If the internal battery fluid gets into your
eyes, do not rub, rinse with clean running
Do
water, and get medical treatment
immediately.
Failure to do so may cause blindness.
WARNING
Do not direct the infrared data port toward
your eye and transmit signals.
Don’t
Doing so may cause harmful effect your eyes.
Do not direct the infrared data port toward
home electric appliances etc. equipped with
Don’t
infrared device when using infrared
communication.
Doing so may cause an accident because of
malfunction of infrared device.
Do not turn on the light with the lighting
luminescence part close to the eyes.
Don’t
Especially to shoot infants or young
children, step away from them 1 m or more.
Doing so may cause blurred vision. Or injury
by dazzling eyes or surprising may occur.
Do not allow a foreign substance such as
water and other liquids, metal parts, or
Don’t
flammables to get in the UIM or microSD
card insertion slot on the terminal.
Doing so may cause fire, burns, injury or
electric shock.
Do not turn on the light toward a driver of a
car etc.
Don’t
Doing so may disturb driving and cause an
accident.
Content s/Precautio ns
12
Power off the terminal in a place where the
use is prohibited such as in airplane or
Do
hospital.
Failure to do so may affect electronic
equipment and electronic medical
equipment. If you set the automatic power-on
function, cancel it before powering off the
terminal.
Follow the instructions of each medical facility
for the use of mobile phones on their
premises.
Prohibited acts such as mobile phone usage
on board an airplane may be punished by law.
If usage of mobile phones in an aircraft is
admitted by setting airplane mode, etc., use
the terminal under the direction of the airline.
If the microUSB cable is connected into the
USB connecting jack for charging etc, the
terminal is automatically powered on
although the operations are not available. Be
careful not to connect the microUSB cable in a
place where the use is prohibited such as in
airplane or hospital.
Always keep the terminal away from your
ear when you talk setting the hands-free
Do
function.
Also, when you play game, play back music,
etc. connecting the Earphone/Microphone,
etc. to the terminal, adjust the volume
adequately.
If the volume is too loud, it may cause
difficulty in hearing.
Moreover, if you barely hear the surrounding
sounds, it may cause an accident.
If you have a weak heart, set the vibrator or
ringtone volume carefully.
Do
Failure to do so may affect your heart.
If you are wearing any electronic medical
equipment, check with the relevant medical
Do
electronic equipment manufacturer or
vendor whether the operation may be
affected by radio waves.
The radio waves from the terminal may affect
electronic medical equipment.
Power off the terminal near electronic
devices or equipment operating on high
Do
precision control or weak signals.
Failure to do so may interfere with the
operation of electronic devices or equipment.
* The followings are some electronic devices
or equipment that you should be careful of:
Hearing aids, implantable cardiac
pacemaker, implantable cardioverter
defibrillator, other electronic medical
equipment, fire detector, automatic door,
and other automatically controlled devices
or equipment.
If you use an implantable cardiac
pacemaker, implantable cardioverter
defibrillator, or other electronic medical
equipment, check with the relevant medical
electronic equipment manufacturer or
vendor whether the operation can be
affected by radio waves.
Be careful about broken glasses or exposed
internal from the terminal if the display or
Do
the camera lens is broken.
Shatterproof film-applied hardened glass is
used on the display surface and the acrylic
resin is applied on camera lens so as not to be
shattered when broken. But they may cause
injury if you touch a cut surface or exposed
portion mistakenly.
Content s/Precautio ns
13
If the internal battery leaks or hears an
unusual odor, immediately stop using and
Do
move it away from fire.
The leaking liquid may ignite fire, catch fire, or
explode.
CAUTION
Do not swing the terminal around by
holding the antenna or strap.
Don’t
The terminal may hit you or others and cause
accident such as injury.
Do not use damaged terminal.
Doing so may cause fire, burns, injury or
Don’t
electric shock.
If the display is mistakenly damaged and
when the liquid crystal runs out, do not get
Don’t
it on your skin such as face, hands, etc.
Doing so may cause blindness or injury on
your skin.
If the liquid crystal gets in your eye or mouth,
rinse with clean running water, and get
medical treatment immediately.
Also, if it gets on your skin or clothes, use
something such as alcohol to wipe off and
wash it with soap in clear water.
Do not discard the battery pack together
with other garbage.
Don’t
The te rminal may become the source of f ire or
environmental destruction. Take the used
terminal to our service counter (docomo
Shop, etc.) or follow the instructions of the
local authorities in charge of collecting used
terminals.
To use the terminal in car, check with
automobile manufacturer or dealer to
Do
determine how the device is affected by
radio waves before using.
In rare cases, using the phone in some vehicle
models can cause the vehicle's electronic
equipment to malfunction. In that case, stop
using the terminal immediately.
The use of the terminal may cause itching,
rashes, eczema, or other symptoms
Do
depending on the user's physical condition.
Immediately stop using and get medical
treatment in such a case.
For material of each part →P. 17 "M at e r ia l li st "
When watching the display, take a certain
distance from the display in a fully bright
Do
place.
Failure to do so may reduce visual acuity.
If fluid etc. leaks out from the internal
battery, do not make the fluid contact with
Do
your skin of face or hands.
Doing so may cause blindness or injury on
your skin.
If th e fluid etc. g ets into your eyes or mout h, or
contacts skin or clothes, immediately flush the
contacted area with clean running water.
If the fluid gets into the eyes or mouth,
immediately see a doctor after flushing.
Content s/Precautio ns
14
3. Handling the adapter and desktop
holder
WARNING
Do not use the microUSB cable if it is
damaged.
Don’t
Doing so may cause fire, burns or electric
shock.
Do not use the AC adapter cable or the
desktop holder in a very humid or steamy
Don’t
place such as bathroom.
Doing so may cause fire, burns or electric
shock.
DC adapter is only for a negative ground
vehicle. Do not use DC adapter for a positive
Don’t
ground vehicle.
Doing so may cause fire, burns or electric
shock.
Do not touch the AC adapter cable if you
hear thunder.
Don’t
Doing so may cause electric shock.
Do not short-circuit the microUSB plug
while it is connected to the power outlet. Do
Don’t
not touch the microUSB plug with your
hands, fingers, or any part of your body.
Doing so may cause fire, burns or electric
shock.
Do not place any heavy objects on the
microUSB cable.
Don’t
Doing so may cause fire, burns or electric
shock.
When you insert and remove AC adapter
from power outlet, do not contact a metal
Don’t
strap or other metal objects with the jack.
Doing so may cause fire, burns or electric
shock.
Do not touch the cord of the AC adapter
cable, the desktop holder or the power
No wet hands
outlet with wet hands.
Doing so may cause fire, burns or electric
shock.
Use the adapter only on the specified power
supply and voltage.
Do
Use the AC adapter cable available overseas
when you charge the battery overseas.
Failure to do so may cause fire, burns or
electric shock.
AC adapter : AC 100 V to 240 V (Make sure to
connect the adapter to a household AC power
outlet.)
DC adapter : DC 12 V or 24 V (only for a
negative-ground vehicle)
When the fuse in a DC adapter is blown,
make sure to use the specified fuse.
Do
Failure to do so may cause fire, burns or
electric shock. For the specified fuse, see the
users manuals that supplied with a DC
adapter.
Clean dust from the power plug.
Failure to do so may cause fire, burns or
Do
electric shock.
When you connect the AC adapter to the
power outlet, insert it firmly.
Do
Failure to do so may cause fire, burns or
electric shock.
Content s/Precautio ns
15
Hold the AC adapter, not the microUSB
cable, when you remove the power plug
Do
from the power outlet.
Failure to do so may cause fire, burns or
electric shock.
Remove the power plug from the power
outlet when not used for a long period of
Unplug
time.
Failure to do so may cause fire, burns or
electric shock.
If liquid such as water gets into the adapter,
immediately remove it from the power
Unplug
outlet.
Failure to do so may cause fire, burns or
electric shock.
Before cleaning, remove the power plug
from the power outlet.
Unplug
Failure to do so may cause fire, burns or
electric shock.
4. Handling the UIM
CAUTION
Please be careful not to touch a cut surface
when you remove the UIM.
Do
Failure to do so may cause injury.
5. Handling the terminal near
electronic medical equipment
■
The following instructions observe the
guidelines of the Electromagnetic
Compatibility Conference, Japan to protect
electronic medical equipment from radio
waves from mobile phones.
WARNING
Please observe the following guidelines in
medical facilities.
Do
・
Do not take the terminal into the operating
rooms, ICU (Intensive Care Unit), or CCU
(Coronary Care Unit).
・
Power off the terminal inside hospital wards.
・
Power off the terminal in the lobby and
other places if there are any electronic
medical equipment operating in the vicinity.
・
Follow the instructions of each medical
facility when they specify areas forbidding to
use and carrying a mobile phone.
・
If you set the automatic power-on function,
cancel it before powering off the terminal.
Power off the terminal in crowded places
such as rush-hour trains. There may be a
Do
person with an implantable cardiac
pacemaker or implantable cardioverter
defibrillator near you.
The radio waves from the terminal may affect
the operation of implantable cardiac
pacemaker or implantable cardioverter
defibrillator.
If you use an implantable cardiac pacemaker
or implantable cardioverter defibrillator,
Do
keep the terminal 22 cm or more away from
the implant at all times.
The radio waves from the terminal may affect
the performance of electronic medical
equipment.
Content s/Precautio ns
16
If you need to use electronic medical
equipment other than implantable cardiac
Do
pacemaker or implantable cardioverter
defibrillator outside medical facilities such
as treating at home, check with the relevant
medical electronic equipment manufacturer
whether the operation may be affected by
radio waves.
The radio waves from the terminal may affect
the performance of electronic medical
equipment.
6. Material list
PartMaterial
Exterior case
(cover front)
(terminal color :
Black)
Exterior case
(cover front)
(terminal color :
Aqua/Sakura/
Ceramic)
Exterior case
(rear frame)
Exterior case
(cover back)
(terminal color :
Black)
SO-03D is waterproof, however, do not
allow water to seep into the terminal and
do not allow accessories or optional
devices to get wet.
AC adapter cable, desktop holder and UIM are
not waterproof. Do not use in a bathroom or
other highly humid area or do not let rain touch.
Or putting the terminal on your body, humidity
of sweat may cause internal corrosion and
malfunction. Not that malfunctions, which are
determined to be caused by water as result of
inspections, are outside the scope of the
warranty. Since these conditions are outside of
the scope of the warranty, a repair, if at all
possible, is charged.
・
Clean the terminal with a dry soft cloth
(such as used for cleaning eyeglasses).
- Do not rub it roughly with a dry cloth. The
display may be damaged.
- Drops of water or dirt left on the display may
cause stains.
- Do not use alcohol, thinner, benzine, cleaning
detergent, etc. to clean the terminal. These
chemicals may erase the printing on the
terminal or cause discoloration.
・
Clean the terminals occasionally with a
dry cotton swab.
If the jack is soiled, connection gets worse and it
may cause power to be turned off or insufficient
battery charge, so clean the jack with a dry
cotton swab etc. When cleaning, be careful not
to damage the terminals.
・
Do not leave the terminal near the air
conditioning vent.
Extreme temperature changes may produce
condensation and corrode the internal parts of
the terminal, causing it to malfunction.
・
Make sure to use the terminal etc. without
excessive force.
If you put the terminal in a bag full of items or sit
down with the terminal in the pocket of your
cloth, it may damage the display and internal
circuit board, and cause the terminal to
malfunction.
Also, while the external device is connected to
the microUSB connecting jack, headset
connecting jack or HDMI connecting jack, it may
damage the connector and cause malfunction.
・
Do not rub or scratch the display with
metal.
The display may get scratched and it may cause
malfunction or damage.
・
Make sure to see the user's manuals
supplied with the AC adapter cable.
Content s/Precautio ns
18
■
The terminal precautions
・
Do not press touch panel surface forcibly,
or not operate with a sharp-pointed
objects such as nail, ballpoint pen, pin,
etc.
Doing so may cause damage of touch panel.
・
Do not use the terminal in extremely hot
or cold places.
Use the terminal where the temperature ranges
℃
between 5
use in a bathroom etc. when temperature is 36
or more) and humidity ranges between 45% and
85%.
・
Using the terminal near ordinary phone,
and 40℃ (limited to the temporary
television or radio may cause interference
in these electric appliances. Make sure to
move far away from them when using the
terminal.
・
Note down the information saved in the
terminal in a separate note and keep it
safely.
Under no condition will DOCOMO be held liable
for any damaged or lost data saved in the
terminal.
・
Do not drop or give a strong impact to the
terminal.
Doing so may cause malfunction or damage.
・
Do not plug the connector of the external
device into the microUSB connecting jack,
headset connecting jack or HDMI
connecting jack at the slant or pull it while
connecting.
Doing so may cause malfunction or damage.
・
The terminal could become warm while
in use and charging. This condition is not
abnormal. You can continue using the
terminal.
・
Do not leave the camera under direct
sunlight.
If you do so, some of the elements may melt or
become faded.
・
Usually use the terminal with the
℃
connecting jack covers for microUSB/
headset/HDMI and covers for UIM card
slot and microSD card slot closed.
Failure to do so may get dust or water inside and
cause malfunction.
・
Do not remove the microSD card or
power off the terminal while using the
microSD card.
Doing so may cause data loss or malfunction.
・
Do not let magnetic cards, etc. close to
the terminal.
The magnetic data in cash cards, credit cards,
telephone cards, floppy disks, etc. may be erased.
・
Do not bring strong magnetic objects
close to the terminal.
Strong magnetic objects may cause
misoperation.
Content s/Precautio ns
19
・
The internal battery is a consumable
accessory.
Even if the operating time of the terminal varies
depending on the operating conditions and
other factors, when the length of time you can
use the terminal with a fully charged battery
becomes unusually short, it is time to replace the
internal battery. For replacement of internal
battery, contact "General Inquiries" on the last
page of this manual or the DOCOMO-specified
repair office.
・
Charge the battery pack in an
environment with the proper ambient
℃
temperature (5
・
The operating time of the internal battery
to 35℃).
varies depending on the operating
environment and the secular degradation
of the internal battery.
・
Do not store the internal battery in the
following cases:
- The battery is fully charged (immediately after
the charging is complete)
- The battery has run out (the phone cannot
power on)
The performance and life of the internal battery
may deteriorate.
It is recommended that you store the internal
battery with the remaining battery level of about
40 percent as a guide.
■
The adapter precautions
・
Charge the battery pack in an
environment with the proper ambient
℃
temperature (5
to 35℃).
・
Do not charge in the following places.
- Places that are very humid, dusty or exposed to
strong vibrations.
- Near ordinary phone or TV/radio.
・
The AC adapter cable could become
warm while charging. This condition is
not abnormal. You can continue using the
terminal.
・
When using the DC adapter for charging,
do not turn off the vehicle engine.
Doing so may cause the vehicle battery run out.
・
When you use the power outlet with a
mechanism to prevent the plug from
being removed, follow the instructions on
the outlet's user's manual.
・
Do not give a strong impact to the
adapter. Also, do not bend or deform the
microUSB plug.
Doing so may cause malfunction.
■
UIM precautions
・
Do not use unnecessary force to insert/
remove the UIM.
・
Note that DOCOMO assumes no
responsibility for malfunctions occurring
as the result of inserting and using UIM
with another IC card reader/writer.
・
Always keep the IC portion clean when
you use the card.
・
Clean the terminal with a dry soft cloth
(such as used for cleaning eyeglasses).
Content s/Precautio ns
20
・
Note down the information saved in the
UIM in a separate note and keep it safely.
Under no condition will DOCOMO be held liable
for any damaged or lost data saved in the
terminal.
・
Take an expended UIM to sales outlet
such as docomo Shop for proper disposal
in order to protect the environment.
・
Do not carelessly damage, contact, or
short-circuit an IC.
Doing so may cause data loss or malfunction.
・
Do not drop a UIM or subject it to impact.
Doing so may cause malfunction.
・
Do not bend a UIM or place a heavy
object on it.
Doing so may cause malfunction.
・
Do not insert the UIM on which any label
or seal is stuck into the terminal.
Doing so may cause malfunction.
■
Bluetooth function precautions
・
To secure the Bluetooth communication
security, the terminal supports the
security function compliant with
Bluetooth standards, but the security may
not be sufficient depending on the
setting. Concern about the
communication using the Bluetooth
function.
・
Please be aware that DOCOMO is not
responsible for data leak when making
data communications using Bluetooth.
・
Frequency band
The frequency band used by the terminal's
Bluetooth/wireless LAN function is as follows.
2.4 : This radio equipment uses the 2400 MHz
band.
Modulation scheme is the
FH/XX/DS/OF
1 : The estimated interference distance is 10
4 : The estimated interference distance is 40
8 : The estimated interference distance is 80
Available channels vary depending on the
country.
For use in an aircraft, contact the airline
beforehand.
:
FH-SS, other system, DS-SS,
or OFDM system.
m or less.
m or less.
m or less.
: The full band between 2400 MHz
and 2483.5 MHz is used and the
band of the mobile identification
device can be avoided.
Content s/Precautio ns
21
・
Bluetooth cautions
The operating frequency band of the terminal is
used by industrial, scientific, consumer and
medical equipment including microwave ovens,
premises radio stations for identifying mobile
units used in the manufacturing lines of plants
(radio stations requiring a license), specified low
power radio stations (radio stations requiring no
license) and amateur radio stations (hereinafter
referred to as "another station").
- Before using this equipment, confirm that
"another station" is not being operated nearby.
- In the event of the terminal causing harmful
radio wave interference with "another station",
promptly change the operating frequency or
stop radio wave emission by turning off the
power, etc.
- If you have further questions, contact "General
Inquiries" on the last page of this manual.
■
Wireless LAN (WLAN) precautions
・
Wireless LAN (WLAN) exchanges
information using radio waves, and allows
you to freely establish LAN connection if
you are within an area where radio wave
reaches. On the other side, if you
communicate without appropriate
security settings, communications may
be intercepted or hacked by malicious
parties. It is recommended to make
necessary security settings on your
responsibility and expense.
・
Wireless LAN
Do not use wireless LAN near magnetic devices
such as electrical appliances or AV/OA devices, or
in radio waves.
- Magnetism or radio waves may increase noises
or disable communications (especially when
using a microwave oven).
- When used near TV, radio, etc., reception
interference may occur, or channels on the TV
screen may be disturbed.
- If there are multiple wireless LAN access points
nearby and the same channel is used, search
may not work correctly.
・
2.4 GHz device cautions
The operating frequency band of the WLAN
device is used by industrial, scientific, consumer
and medical equipment including home electric
appliances such as microwave ovens, premises
radio stations for identifying mobile units used in
the manufacturing lines of plants (radio stations
requiring a license), specified low power radio
stations (radio stations requiring no license) and
amateur radio stations (radio stations requiring a
license).
- Before using the device, confirm that premises
radio stations for identifying mobile units,
specified low power radio stations and amateur
radio stations are not being operated nearby.
- If the device causes harmful radio interference
to premises radio stations for identifying
mobile units, immediately change the
frequency band or stop use, and contact
"General Inquiries" on the last page of this
manual for crosstalk avoidance, etc. (e.g.
partition setup).
Content s/Precautio ns
22
- If the device causes radio interference to
specified low power radio stations or amateur
radio stations, contact "General Inquiries" on
the last page of this manual.
■
FeliCa reader/writer function
precautions
・
FeliCa reader/writer function of the
terminal uses weak waves requiring no
licenses for radio stations.
・
It uses 13.56 MHz frequency band. When
using other reader/writers in your
surroundings, keep the terminal away
sufficiently from them. Before using the
FeliCa reader/writer, confirm that there
are no radio stations using the same
frequency band nearby.
■
Note
・
Do not use altered terminal. Using an
altered device is a violation of the Radio
Law.
A "Technical Conformity Mark " affixed on the
manufacturer's specification sticker certifies that
the terminal meets technical regulations for
specified radio equipment that are based on the
Radio Law.
If you remove the screws and alter the inside of
the terminal, the technical regulations
conformity certification becomes invalid.
Do not use the terminal with the certification
invalid, as it is a violation of the Radio Law.
・
Be careful when using the terminal while
driving.
Using a handheld mobile phone while driving
will result in a penalty.
However, absolutely necessary cases such as
rescue of a sick person or maintaining public's
safety are exempted.
・
Use the FeliCa reader/writer function only
in Japan.
FeliCa reader/writer function of the terminal
conforms to Japanese radio standards. If you use
this function overseas, you may be punished.
・
Do not alter the basic software illegally.
It is regarded as the software modification and
Repairs may be refused.
Content s/Precautio ns
23
Waterproofness
SO-03D provides waterproofness of IPX5*1,
*2
with firmly closing the the connecting
IPX7
jack covers for microUSB/headset/HDMI and
covers for UIM card slot and microSD card
slot.
*1 IPX5 means that a phone keeps functioning
after applying a jet flow of 12.5 L/min. from
every direction from a distance of
approximately 3 m for at least 3 minutes
using water nozzle in 6.3 mm inner
diameter.
*2 IPX7 means that a phone keeps functioning
after SO-03D is slowly submerged to depth
of 1 m in static tap water at room
temperature, left there for 30 minutes and
then taken out.
What you can do with
waterproofness of SO-03D
・
You can talk without an umbrella in the rain
(for rainfall of 20 mm or less per hour).
- Do not open or close the connecting jack
covers for microUSB/headset/HDMI and
covers for UIM card slot and microSD card
slot when your hands get wet or waterdrops
are attached to the terminal.
・
You can wash the terminal when it is dirt or
liquid other than tap water put on.
- Wash the terminal with tap water at normal
℃
temperature (5
flow (less than 6 L/min.) at distance of
approximately 10 cm away from the tap or
shower.
- When you wash the terminal, hold the
connecting jack covers for microUSB/
headset/HDMI and covers for UIM card slot
and microSD card slot, with your hands
without using brush or sponge. After
washing, drain the terminal before use.
(P.27)
・
You can use at a poolside.
- If the terminal gets wet with water from the
swimming pool or submerged into a pool,
wash it with tap water.
-35℃) by weaker water
Content s/Precautio ns
24
・
You can use the terminal in a bathroom.
- Do not put the terminal in the bathtub. Do
not use the terminal in hot water. Doing so
may cause malfunction.
- Never put the termi nal in hot spring water or
water containing soap, detergent or bath
powder.
- Use the terminal where the temperature
℃
ranges between 5
and 40℃ (limited to the
temporary use in a bathroom etc. when
temperature is 36
℃
or more) and humidity
ranges between 45% and 85%.
- Rapidly changing temperature may cause
dew condensation. If you bring the terminal
from cold area to warm bathroom etc., wait
for the terminal to become room
temperature.
To ensure waterproofness
To avoid water ingress, be sure to observe the
following points.
・
Do not throw any liquid other than room
temperature tap water on the terminal, or
soak it in such liquid.
・
When using the microUSB connecting jack or
removing/inserting microSD card, pull the
cover up with your finger by the groove.
Open the connecting jack covers for headset/
HDMI and UIM card slot cover in the same
way.
Groove
Groove
After using microUSB connecting jack or
removing/inserting microSD card, push the
cover in the direction of the arrow and ensure
there is no gap.
Close the connecting jack covers for headset/
HDMI and UIM card slot cover in the same
way.
・
Firmly close the connecting jack covers for
microUSB/headset/HDMI and covers for UIM
card slot and microSD card slot. Even a fine
obstacle (one hair, one grain of sand, tiny fiber,
etc.) put between contact surfaces may allow
water to enter.
・
Do not poke the microphone, earpiece or
speaker with a swab or sharp object.
Content s/Precautio ns
25
・
Do not let the terminal fall. It may become
scratched causing the waterproof
performance to degrade.
・
The rubber packing of the rear side of the
connecting jack covers for microUSB/
headset/HDMI and covers for UIM card slot
and microSD card slot play important roles for
keeping waterproof performance. Do not
remove or damage them. Also, prevent dust
from adhering to it.
To keep the terminal waterproofness, replacement
of parts is required every 2 years regardless of
whether the terminal appears normal or abnormal.
DOCOMO replaces the parts as a chargeable
service. Bring the terminal to a sales outlet such as
a DOCOMO-specified repair office.
Important precautions
Do not perform actions shown in the
illustrations below.
<Example>
Using in hot
spring
Machine-
washing
Applying strong
Attaching
sand/mud
water ow
Bath powder
Washing with
brush/sponge
Soaking in
ocean water
Using Soap/Detergent/
Observe the following precautions to use the
terminal properly.
・
Accessories and optional devices are not
waterproof. When watching 1Seg, etc. with
the terminal installed in the supplied desktop
holder, do not use it in a bathroom, shower
room, kitchen or lavatory even if it is not
connected to the AC adapter cable.
・
Do not apply water flow stronger than
allowed (water flow of 6L/min. or more : e.g.,
such water flow that gives you pain when
applied to your skin directly from a faucet or
shower). SO-03D provides IPX5
waterproofness, but doing so may cause
malfunction.
Content s/Precautio ns
26
・
If the terminal gets wet with salt water, sea
water, refreshing beverage or mud or sand
adhered, wash it immediately. If they dry out,
it is hard to remove the dirt and it may cause
damage or malfunction.
・
Do not put the terminal in hot water, use it in
a sauna or apply hot airflow (from a hair dryer
etc.) to it.
・
Do not move the terminal in water or slam the
terminal against the surface of water.
・
If you put the terminal in tap water or in water
of swimming pool, be sure to have it within 30
minutes.
・
When you use the terminal in swimming pool,
obey rules of the facility.
・
The terminal does not float on water.
・
Do not leave water on the terminal. In cold
area, the terminal freezes up and may cause
malfunction.
・
Do not leave water on the microphone,
earpiece or speaker. Such water may interfere
with talking.
・
If the terminal gets wet with water or other
liquids with the connecting jack covers for
microUSB/headset/HDMI and covers for UIM
card slot and microSD card slot open, the
liquid may get inside the terminal causing
electric shocks or malfunction. Stop using the
terminal, turn the power OFF and contact a
DOCOMO-specified repair office.
・
If the rubber gasket on the rear side of
connecting jack covers for microUSB/
headset/HDMI and covers for UIM card slot
and microSD card slot are damaged or
deformed, replace it at DOCOMO-specified
repair office.
DOCOMO does not guarantee actual operations
under all states. Malfunctions deemed to be caused
by inappropriate operation by the customer are
not covered by the warranty.
Draining water from the
terminal
When the terminal is wet, water may flow out
after wiping it off; drain the water in the
following steps.
a
Hold the terminal firmly and wipe off moisture on
the terminal surface and back side with dry, clean
cloth etc.
Content s/Precautio ns
27
b
Shake the terminal approximately 20 times, firmly
holding it, until there is no more water splattering.
c
Swing the terminal in about 10 times against dry,
clean cloth etc. to wipe off water remaining in the
microphone, earpiece, speaker, power key, volume
key, camera key, contacts for the desktop holder,
each cover (connecting jack covers for microUSB/
headset/HDMI and covers for UIM card slot and
microSD card slot), etc.
d
Wipe off water drained from the terminal with dry,
clean cloth etc., and dry naturally.
・
Water, if any, remaining in the terminal may ooze
up after wiping off.
・
Do not wipe off water remaining in gaps directly
with a cotton swab etc.
Charging
Check the following before and after
charging.
・
Check if the terminal is not wet. Never try to
charge the battery pack when the terminal is
wet.
・
Accessories and optional devices are not
waterproof.
・
When charging the battery when or after the
terminal is wet, adequately drain it and wipe
off water with a dry, clean cloth etc., before
connecting the supplied desktop holder or
opening the microUSB connecting jack cover.
・
When the microUSB connecting jack cover is
opened for charging, close the cover firmly
after charging. It is recommended to use the
desktop holder for charging to prevent water
from seeping inside from the microUSB
connecting jack.
・
Do not use the AC adapter cable or desktop
holder in a bathroom, shower room, kitchen,
lavatory or other highly humid area. May
cause fire or electric shock.
・
Do not touch the AC adapter cable or desktop
holder with wet hands. May cause electric
shock.
Content s/Precautio ns
28
Loading...
+ 256 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.