Sony SNC-DM160 User Manual
3-873-170-13 (1)
Network Camera
Installation Manual
Before operating the unit, please read this manual thoroughly and
retain it for future reference.
SNC-DM160
SNC-DS60
2008 Sony Corporation Printed in China
Owner’s Record
The model and serial numbers are located on the bottom. Record these
numbers in the spaces provided below.
Refer to these numbers whenever you call upon your Sony dealer regarding
this product.
Model No. Serial No.
WARNING
To avoid electrical shock, do not open the cabinet. Refer
servicing to qualied personnel only.
WARNING
This installation should be made by a qualied service person and should
conform to all local codes.
WARNING
A readily accessible disconnect device shall be incorporated in the building
installation wiring.
WARNING (for Installers only)
Instructions for installing the equipment on the ceiling or the wall:
After the installation, ensure the connection is capable of supporting four
times the weight of the equipment downwards.
CAUTION
The rating label is located on the bottom.
CAUTION for LAN port
For safety reason, do not connect the LAN port to any network devices that
might have excessive voltage.
The LAN port of this unit is to be connected only to the devices whose
power feeding meets the requirements for SELV (Safety Extra Low Voltage)
and complies with Limited Power Source according to IEC 60950-1 Second
Edition.
Power Supply
Caution for U.S.A. and Canada
The SNC-DM160/DS60 operates on 24V AC or 12V DC.
The SNC-DM160/DS60 automatically detects the power.
Use a Class 2 power supply which is UL Listed (in the U.S.A.) or CSA-certied
(in Canada).
Caution for other countries
The SNC-DM160/DS60 operates on 24V AC or 12V DC.
The SNC-DM160/DS60 automatically detects the power.
Use a power supply rated 24 V AC or 12 V DC which meets the requirements
for SELV (Safety Extra Low Voltage) and complies with Limited Power Source
according to IEC 60950-1 Second Edition.
For customers in the U.S.A.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
You are cautioned that any changes or modications not expressly approved
in this manual could void your authority to operate this equipment.
All interface cables used to connect peripherals must be shielded in order to
comply with the limits for a digital device pursuant to Subpart B or Part 15 of
FCC Rules.
For customers in Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du
Canada.
For the customers in Europe
The manufacturer of this product is Sony Corporation, 1-7-1 Konan, Minatoku, Tokyo, Japan.
The Authorized Representative for EMC and product safety is Sony
Deutschland GmbH, Hedelnger Strasse 61, 70327 Stuttgart, Germany.
For any service or guarantee matters please refer to the addresses given in
separate service or guarantee documents.
For the customers in Europe, Australia and New Zealand
WARNING
This is a Class A product. In a domestic environment, this product may cause
radio interference in which case the user may be required to take adequate
measures.
In the case that interference should occur, consult your nearest authorized
Sony service facility.
This apparatus shall not be used in the residential area.
ATTENTION
The electromagnetic elds at specic frequencies may inuence the picture
of the unit.
Notes on Use
Before Use
If you nd condensation when you open the package, turn on the power after
leaving it out for about 60 minutes.
Data and security
You should keep in mind that the images or audio you are monitoring may be
protected by privacy and other legal rights, and the responsibility for making
sure you are complying with applicable laws is yours alone.
Access to the images and audio is protected only by a user name and the
password you set up. No further authentication is provided nor should you
presume that any other protective ltering is done by the service. Since
the service is Internet-based, there is a risk that the image or audio you are
monitoring can be viewed or used by a third-party via the network.
SONY IS NOT RESPONSIBLE, AND ASSUMES ABSOLUTELY NO LIABILITY TO YOU
OR ANYONE ELSE, FOR SERVICE INTERRUPTIONS OR DISCONTINUATIONS OR
EVEN SERVICE CANCELLATION. THE SERVICE IS PROVIDED AS-IS, AND SONY
DISCLAIMS AND EXCLUDES ALL WARRANTIES, EXPRESS OR IMPLIED, WITH
RESPECT TO THE SERVICE INCLUDING, BUT NOT LIMITED TO, ANY OR ALL
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR THAT IT WILL OPERATE ERROR-FREE OR CONTINUOUSLY.
Security conguration is essential for wireless LAN. Should a problem
occur without setting security, or due to the limitation of the wireless LAN
specications, SONY shall not be liable for any damage, loss of recorded data
or restoration thereof.
Always make a test recording, and verify that it was recorded successfully.
SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT
LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF FAILURE
OF THIS UNIT OR ITS RECORDING MEDIA, EXTERNAL STORAGE SYSTEMS OR
ANY OTHER MEDIA OR STORAGE SYSTEMS TO RECORD CONTENT OF ANY TYPE.
Always verify that the unit is operating properly before use. SONY WILL NOT
BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO,
COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT
OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE
WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY
OTHER REASON WHATSOEVER.
If you lose data by using this unit, SONY accepts no responsibility for
restoration of the data.
Personal information
The images taken by the system using this device can identify individuals
and thus they fall under “personal information” stipulated in the “Act on the
Protection of Personal Information”. Please handle the video data appropriately
according to law.
Information recorded using this product may also be “personal information”.
Upon disposal, transfer, repair, or any other occasion where this product or
storage media is passed on to a third party, practice due care in its handling.
Operating or storage location
Do not shoot an extremely bright object (an illumination, the sun, etc.). Also,
avoid operating or storing the camera in the following locations, as these can be
a cause of a malfunction.
Extremely hot or cold places (Operating temperature: –30°C to +50°C [–22°F
to 122°F])
Close to heating equipment (e.g., near heaters)
Close to sources of strong magnetism
Close to sources of powerful electromagnetic radiation, such as radios or TV
transmitters
Locations subject to strong vibration or shock
Dusty locations
Locations under the inuence of uorescent light or reection of a window
Under an unsteady light (the image will icker.)
Using in cold climates
This device is equipped with a built-in heater which automatically operates
when the internal temperature drops signicantly low. However, the heater
may not defrost snow and frost attached on the dome cover under certain
environment condition.
Operating temperature
Be sure to turn the power on from 0°C to 50°C (32°F to 122°F).
When the power is on, the built-in heater enables the camera unit to operate
from –30°C to +50°C (–22°F to +122°F).
Ventilation
To prevent heat buildup, do not block air circulation around the camera.
Transportation
Always turn o the power when carrying.
When transporting the camera, repack it as originally packed at the factory or
in materials of equal quality.
Cleaning
Use a blower to remove dust from the lens.
Use a soft, dry cloth to clean the external surfaces of the camera. Stubborn
stains can be removed using a soft cloth dampened with a small quantity of
detergent solution, then wipe dry.
Do not use volatile solvents such as alcohol, benzene or thinners as they may
damage the surface nishes.
To install the camera outdoors
Attach the dome casing securely to the unit casing.
Make sure you seal the locations listed below with sealant (e.g. silicon sealant) to
prevent moisture from getting inside the casing.
- Camera installation holes (4)
- Conduit holes (side/bottom)
Note on laser beams
Laser beams may damage a CCD. You are cautioned that the surface of a CCD should
not be exposed to laser beam radiation in an environment where a laser beam device is
used.
Recommendation of Periodic Inspections
In case using this device over an extended period of time, please have it
inspected periodically for safe use.
It may appear awless, but the components may have deteriorated over time,
which may cause a malfunction or accident.
For details, please consult the store of purchase or an authorized Sony dealer.
Phenomena Specic to CCD Image Sensors
The following phenomena that may appear in images are specic to CCD (Charge
Coupled Device) image sensors. They do not indicate malfunctions.
White ecks
Although the CCD image sensors are produced with high-precision technologies,
ne white ecks may be generated on the screen in rare cases, caused by cosmic
rays, etc.
This is related to the principle of CCD image sensors and is not a malfunction.
The white ecks especially tend to be seen in the following cases:
- when operating at a high environmental temperature
- when you have raised the gain (sensitivity)
- when using the slow shutter
Vertical smear
When an extremely bright object, such as a strong spotlight or ashlight, is
being shot, vertical tails may be produced on the screen, or the image may be
distorted.
Monitor screen
Vertical tails shown on the image
Bright object (e.g. strong spotlight,
strong reected light, ashlight, the sun)
Aliasing
When ne patterns, stripes, or lines are shot, they may appear jagged or icker.
About the Supplied Manuals
Installation Manual (this document)
This Installation Manual describes the names and functions of parts and controls
of the Network Camera, gives connection examples and explains how to set up
the camera. Be sure to read the Installation Manual before operating.
Easy Setup Guide for the Sony Network Camera (stored in
the CD-ROM)
The Easy Setup Guide shows you how to set up the camera in order to view the
image shot by the camera on a computer.
After installing and connecting the camera following the Installation Manual,
perform setup using the Easy Setup Guide.
User’s Guide (stored in the CD-ROM)
The User’s Guide describes how to set up the camera and how to control the
camera via a Web browser. Operate the camera referring to the User’s Guide.
Using the CD-ROM Manuals
The supplied CD-ROM disc includes the User’s Guides and Easy Setup Guides for
this unit in PDF format.
Preparations
The Adobe Reader Version 6.0 or higher must be installed on your computer in
order to use the guides stored in the CD-ROM disc.
Note
If Adobe Reader is not installed, it may be downloaded from the following URL:
http://www.adobe.com/
Reading the manual in the CD-ROM
1 Insert the CD-ROM in your CD-ROM drive.
A cover page appears automatically in your Web browser.
If it does not appear automatically in the Web browser, double-click on the
index.htm le on the CD-ROM.
2 Select and click on the manual that you want to read.
This opens the PDF le of the manual.
Clicking an item in the Table of Contents allows you jump to the relevant
page.
Notes
The les may not be displayed properly, depending on the version of Adobe
Reader. In this case, install the latest version, which you can download from
the URL mentioned in “Preparations” above.
If you have lost or damaged the CD-ROM, you can purchase replacement.
Contact your Sony service representative.
Adobe and Acrobat Reader are trademarks of Adobe Systems Incorporated in the United
States and/or other countries.
Location and Function of Part
The gure shows the camera without the dome casing and the slit cover.
Side
Cables , and are not connected when the unit comes from the factory.
Audio cable (supplied)
The connector with the longer cable (SP) is used for the line output
connector, and the shorter cable (MIC) is used for the microphone/line input
connector.
I/O (Input/Output) cable (supplied)
This cable is provided with a sensor input and two alarm outputs.
The wires of the cable control the following signals.
Color of wire Name
Red Sensor In +
White Sensor In – (GND)
Black Alarm Out 1 +
Yellow Alarm Out 1 –
Brown Alarm Out 2 +
Green Alarm Out 2 –
For details on each function and required settings, see the User’s Guide stored in
the supplied CD-ROM.
For the wiring, see “Connecting the I/O cable.”
Wiring slit
Feed the wire rope through this.
For details, see “Installing the Camera” on the reverse side.
Camera head holder
Lens
LAN cable (RJ-45) (supplied and connected to the camera at the factory)
Connect this cable to a hub or computer on the 10BASE-T or 100BASE-TX
network using a network cable (UTP, category 5).
Power input cable (supplied and connected to the camera at the factory)
Connect this cable to a 24 V AC or 12 V DC power supply system.
You can screw an extension cable in the connector tip attached at the end of
the cable.
BNC cable (supplied)
Outputs a composite video signal.
Conduit holes (3/4 inch)
Connect a pipe to this hole. There are two conduit holes on the unit casing,
one on the side and one at the bottom. The cover plug is installed in the side
conduit hole at the factory. Remove the plug as needed and connect the pipe
to the hole.
Lens ring xing screw
Loosen this screw before adjusting the zoom and focus, and tighten it to x
the lens position. The screw can be inserted at one of three points.
Zoom ring
Turn this ring to adjust the angle of view.
Focus ring
Turn this ring to adjust the focus.
Inside
Camera unit
LAN port
Connect the supplied LAN cable.
AC / DC IN (power input) connector
Connect the supplied power input cable to this connector.
EXT CTRL (external control input/output) connector
Connect the supplied I/O cable to this connector.
POWER indicator (green)
When the power is supplied to the camera, the camera starts checking
the system. If the system is normal, this indicator lights up.
NETWORK indicator (green)
The indicator ashes in green when the camera is connected to the
network. The indicator goes o when the camera is not connected to the
network.
VIDEO OUT (video output) indicator
The indicator shows the camera operation mode according to the VIDEO
OUT selector setting. It goes o in IP mode, lights in green in NTSC+IP
mode and lights in orange in PAL+IP mode.
Camera installation hole (4 positions)
Make sure to tighten the screws securely when installing the camera.
MONITOR output jack
Connect this jack to a video input connector of a video monitor. You
can adjust the camera or lens while looking at the image on the video
monitor. After adjusting the camera or lens, disconnect the cable.
VIDEO OUT (video output) connector
Connect the supplied BNC cable to this connector.
AUDIO connector
Connect the supplied audio cable to this connector.
AUDIO IN (audio input) selector
Select the level of the audio signal to be input to the microphone/line
input connector.
LINE: line input level
MIC: microphone input level
The factory default setting is MIC.
IRIS selector
Use this selector when adjusting the focus of the lens.
Each time you press the selector button, the iris of the lens switches
between open and normal. (The factory default setting is normal.)
When the iris is set to open, the IRIS OPEN indicator and the focus assist
indicator appear on a monitor screen. When the VIDEO OUT selector is
set to the NTSC+IP or PAL+IP mode, the indicators are displayed on the
monitor connected to the MONITOR jack or VIDEO OUT connector. When
it is set to the IP mode, the indicators are displayed on the monitor of the
computer.
For details, see “Focus Assist Function” on the reverse side.
VIDEO OUT selector
Each time you press the selector button, the camera operation mode
switches from IP mode to NTSC+IP mode to PAL+IP mode cyclically, and
the VIDEO OUT indicator shows the selected mode. (The factory default
setting is IP mode.)
When adjusting the eld of view using a video monitor, select the
appropriate video signal with this selector.
IP mode: The video signal is not output from the MONITOR jack or VIDEO
OUT connector. (VIDEO OUT indicator: o)
NTSC+IP mode: The NTSC video signal is output from the MONITOR jack
and VIDEO OUT connector. (VIDEO OUT indicator: lights in green)
PAL+IP mode: The PAL video signal is output from the MONITOR jack
and VIDEO OUT connector. (VIDEO OUT indicator: lights in orange)
Note
In NTSC+IP or PAL+IP mode, the video and audio signals can be output to
a computer via a LAN although there are certain restrictions. For details
of the restrictions, see the User’s Guide.
Reset switch
To reset the camera to the factory default settings, hold down this switch
with a point and supply the power to the camera.
Camera head xing screw
First loosen the screw and face the camera head to the desired direction,
then tighten the screw to x it.
Safety cord
This cord prevents the dome casing from falling o the unit casing.
Dome casing
The dome cover is made of polycarbonate. A waterproof rubber gasket is
provided on the joint surface to the unit casing.
(continued on the reverse side)
1
2
3
4
5
1
2
)
8
/
3
85.7 (3
Wiring slit
)
32
/
9
83.5 (2
85.7 (3 3/8)
46 (1 13/16)
Position of conduit hole
12 mm (1/2 inch) or less
Hole for
connecting
cables
ø73 (2 7/8)
Horizontal marker
Hole for
installing the
bracket
Vertical marker
Unit: mm (inches)
Slit cover
1
2, 3
Ceiling
Ceiling
LAN cable
Network cable
(straight, not
supplied)
10BASE-T/
100BASE-TX
Ceiling
Router or hub
)
4
/
3
119 (4
Camera unit mounting
screw (supplied) (4)
Lens ring xing screw hole
Focus assist indicator
1
Power
input
cable
ø166 (6 5/8)
Bracket
(supplied)
Positioning hole
Wire rope (supplied)
Shoulder
screw
(supplied)
2
120 (4
3
/
4
)
4- ø5
(7/32)
hole
Unit: mm (inches)
Preparations
Connecting the Cables to the Camera
Before installation, connect the supplied cables to the camera as required for
your usage and wire them.
1 Remove the dome casing and slit cover.
Loosen the four xed screws of the dome casing using the supplied wrench
and lift the dome casing. Then, remove it by expanding the slit cover.
2 Pass the cables through the conduit hole on the bottom of the camera
unit.
When you route the cables from the side of the camera unit, see “Connecting
to the side conduit hole”.
3 Connect the cables to the connectors on the camera unit.
I/O cable: to EXT CTRL connector
BNC cable: to VIDEO OUT connector
Audio cable: to AUDIO connector
4 Pass the cables through the guides to secure the cables. (-4)
5 Pull the cables gently from the bottom of the camera unit to take in the
slack.
Connecting to the side conduit hole
The cables are set up at the factory to pass through the bottom conduit hole. If
you want to use the side conduit hole, perform the following steps:
Remove the conduit hole cover.
Disconnect the cables from the connectors, and pull them out from the
bottom conduit hole.
Insert the cables through the side conduit hole, and connect the cables to
their respective connectors.
Pass the cables through the guides to secure the cables. (-5)
Attach the conduit hole cover that was removed from the side conduit hole
to the bottom conduit hole.
Notes
If the bottom conduit hole is dirty, the conduit hole cover cannot be xed
rmly. In this case, moisture may leak into the casing and this may cause a
malfunction. Wipe o the dust with a soft cloth, and x the conduit hole cover
rmly.
Cover the joint part of the pipe/cover with silicon sealant, etc. to prevent
moisture from getting inside the casing.
When you install the camera on a wall lengthwise, position the side conduit
hole directly below to prevent moisture from getting inside the casing. (-1)
Use a pipe/plug with a thread length of 12 mm (1/2 inch) or less so that it does
not damage the camera. (-2)
Installation
WARNING
If you attach the camera in the height such as the wall or the ceiling, etc.,
entrust the installation to an experienced contractor or installer.
If you install the camera at a height, ensure that the installation location
and its material are strong enough to withstand a weight of 15 kg (33
lb 11 oz) or more, and then install the camera securely. If they are not
strong enough, the camera may fall and cause serious injury. If the
ceiling is not strong enough, the camera may fall and cause serious
injury.
To prevent the camera from falling, make sure to attach the supplied
wire rope.
If you attach the camera to the ceiling, check periodically, at least once
a year, to ensure that the connection has not loosened. If conditions
warrant, make this periodic check more frequently.
Deciding the Installation Location of the Camera
After deciding the direction in which the camera will shoot, make the required
hole (ø 73 mm (2 7/8 inches)) for the connecting cables using the supplied
template. Then decide the four mounting hole positions to install the bracket.
Mounting screws
The supplied bracket is provided with eight ø 4.5 mm (3/16 inch) mounting holes.
Install the bracket on a ceiling or wall with screws through four mounting holes:
two 83.5 mm (3 9/32 inch)-pitched holes or four 85.7 mm (3 3/8 inch)-pitched holes.
The required mounting screws dier depending on the installation location and
its material. (Mounting screws are not supplied.)
Steel wall or ceiling: Use M4 bolts and nuts.
Wooden wall or ceiling: Use M4 tapping screws. The panel thickness must be 15
mm (5/8 inch) or more.
Concrete wall: Use anchors, bolts and plugs suitable for concrete walls.
Junction box: Use screws to match the holes on the junction box.
WARNING
The required mounting screws dier depending on the installation location and
its material. If you do not secure the camera with the appropriate mounting
screws, the camera may fall o.
Installing the Camera
1 Install the supplied bracket on the ceiling or wall.
Refer to “Mounting screws” for screws to be used.
2 Fix the supplied wire rope to the camera unit and the ceiling or wall.
Fix the wire rope with the supplied shoulder screw to the hole for the wire
rope on the bottom of the camera unit.
Fix the wire rope to the ceiling or wall.
When you install the camera on a wall, feed the cables through it. (
3 Attach the camera unit to the bracket with the supplied four screws.
The screws have a fall-prevention mechanism. The screws inserted into the
screw holes of the camera unit do not fall even if you turn the camera unit
upside down.
Turn the camera unit to click and x one of the projections on the bottom of
the camera to the positioning hole of the bracket. There are four projections
with an angle of 90 degrees, so you can select one of four directions.
Note
If you cannot use screws on a ceiling or wall, or if you want to make the camera
less conspicuous, use the YT-ICB45 in-ceiling bracket (optional) with which you
can mount the camera on the ceiling.
Adjusting the Camera Direction and Coverage
1 Loosen the camera head xing screw.
2 Adjust the camera to turn the lens in the desired direction.
3 Tighten the camera head xing screw to x the camera.
4 Loosen the lens ring xing screw.
5 Turn the zoom ring to adjust the angle of view.
6 Turn the focus ring to adjust the focus.
For easy focus adjustment, use the focus assist indicator that is displayed on
the monitor screen. See “Focus Assist Function” below.
7 Tighten the lens ring xing screw to x the zoom and the focus.
8 Repeat steps 1 to 7 until the coverage and the focus are determined.
Notes
When you adjust the camera head angle without loosening camera head
xing screw, an internal part may be damaged.
If the camera head is too heavy to be adjusted, loosen the camera head xing
screw until it moves freely.
When the lens is not put in the slit of the camera head holder, the moving
range of the camera head is limited.
Do not turn the lens more than 360 degrees, as this may damage the wiring
inside.
There are three screw holes for xing the lens ring at 120 degree intervals. If
the lens ring xing screw poses a problem for adjusting the camera direction
and coverage due to the direction of the camera head, detach the screw
and reattach it to another screw hole, then adjust the camera direction and
coverage again.
When adjusting the angle, be sure that the TOP mark on the camera head
section faces the ceiling. If the camera is installed with the TOP mark facing the
oor, the image appears upside down.
Focus Assist Function
1 Select the camera operation mode to match the video monitor in use
with the VIDEO OUT selector.
2 Set the iris to open with the IRIS selector.
The IRIS OPEN indicator and the focus assist indicator appear on the monitor
screen.
The length of bar varies according to the degree of focus adjustment. Bar
indicates the peak hold value.
3 Turn the focus ring until bar reaches the peak hold value .
Attaching the Dome Casing
1 Attach the slit cover.
Notes
The proper position of the slit cover is slightly apart from the camera
mount. Do not push in by force.
If you cannot attach the slit cover because the barrier of the lens ring xing
screw prevents it, attach the lens ring xing screw to another screw hole.
There are three screw holes for the lens ring xing screw on the concentric
circle.
-1)
2 Fix the dome casing and the camera unit.
Align four screw holes on the dome casing with that on the camera unit,
and tighten four screws with the supplied wrench to secure the dome
casing.
Note
Make sure that the cord does not get caught between the dome casing
and the unit casing. Rotate the cord and adjust the position of the cord.
Connection
Connecting to the Network
Connect the LAN cable of the camera to a router or hub in the network using
the network cable (straight, not supplied).
To connect to a computer
Connect the LAN cable of the camera to the network connector of a
computer using the network cable (cross, not supplied).
Connecting the Power Source
There are three ways to supply the power source to this camera, as follows.
12 V DC
24 V AC
Power supply equipment pursuant to IEEE802.3af (PoE* system)
*PoE means Power over Ethernet.
Note
If the power is supplied from the power input cable and LAN cable at the
same time, the power from the LAN cable has priority over the other.
Connecting to 12 V DC or 24 V AC source
Connect the power input cable of the camera to a 12 V DC or 24 V AC source.
Use a 12 V DC or 24 V AC source isolated from 100 to 240 V AC. Each usable
voltage ranges are as follows.
12 V DC: 10.8 V to 13.2 V
24 V AC: 21.6 V to 26.4 V
Use UL cable (VW-1 style 1007) for these connections.
Connecting to the power supply equipment pursuant to
IEEE802.3af
The power supply equipment pursuant to IEEE802.3af supplies the power
through the LAN cable. For details, refer to the Instruction Manual of the
equipment.
Connecting the I/O Cable
Connect the wires of the I/O cable as follows:
Wiring diagram for sensor input
Mechanical switch/open collector output device
Camera inside
Wiring diagram for alarm output
Camera inside
Magnet relay
24 V AC/24 V DC,
1 A or less
3.3 V
2.2 kohms
Red (Sensor In +)
White (GND)
GND
Black or brown
(Alarm Output +)
Yellow or green
(Alarm Output –)
Outside
Mechanical
switch
or
Open collector output device
Outside
5 V
Circuit example
R
GND
Specications
Compression
Video compression format JPEG/MPEG4
Audio compression format G.711/G.726 (40, 32, 24, 16 kbps)
Maximum frame rate 30 fps
Camera SNC-DM160
Signal system NTSC color system/PAL color system (switchable)
Image device 1/3 type interline transfer (ExwavePRO) CCD
Total picture elements: Approx. 1,320,000
Eective picture elements: Approx. 1,250,000
Synchronization Internal synchronization
Horizontal resolution 600 TV lines (analog video)
Video S/N (AGC 0 dB) 50 dB or more
Minimum illumination (F1.3, 50 IRE)
Color: 0.4 lx (AGC 30 dB, normal readout), 0.1 lx
Black & White: 0.08 lx (AGC 30 dB, normal
Camera SNC-DS60
Signal system NTSC color system/PAL color system (switchable)
Image device 1/4 type interline transfer (ExwavePRO) CCD
Total picture elements: Approx. 350,000
Eective picture elements: Approx. 330,000
Synchronization Internal synchronization
Horizontal resolution 400 TV lines (analog video)
Video S/N (AGC 0 dB) 50 dB or more
Minimum illumination (AGC 36 dB, F1.3, 50 IRE)
Color: 0.15 lx, Black & White: 0.01 lx
Lens (standard equipment of SNC-DM160)
Focal length 2.8 mm to 10 mm
Maximum relative aperture F1.3
View angle Vertical: 73.9° to 20.8°, Horizontal: 100.8° to 27.7°
Minimum object distance 300 mm (11
Lens (standard equipment of SNC-DS60)
Focal length 2.8 mm to 10 mm
Maximum relative aperture F1.3
View angle Vertical: 54.7° to 15.6°, Horizontal: 73.9° to 20.8°
Minimum object distance 300 mm (11
Interface
LAN port 10BASE-T/100BASE-TX, auto negotiation (RJ-45)
I/O port Sensor input : × 1, make contact, break contact
Alarm output : × 2, 24 V AC/DC, 1 A (mechanical
Video output VIDEO OUT: BNC, 1.0 Vp-p, 75 ohms, unbalanced,
Microphone input* Minijack (monaural)
Plug-in-power supported (rated voltage: 2.5 V DC)
Line input* Minijack (monaural)
* The microphone input and the line input are switchable with a selector.
Line output Minijack (monaural), Maximum output level: 1
Others
Power supply 12 V DC ± 10%, 24 V AC ± 10%, 50/60 Hz,
Power consumption 12.9 W max.
Operating temperature When power is on: 0°C to 50°C (32°F to 122°F)
When applying current: –30°C to +50°C (–22°F to
Storage temperature –20°C to +60°C (–4°F to +140°F)
Operating humidity 20% to 80% (Non-condensing)
Storage humidity 20% to 95%
Dimensions (diameter/height)
166 mm × 119 mm (6
Mass Approx. 1.45 kg (2 lb 21 oz), not including the
Supplied accessories CD-ROM (User’s Guides, Easy Setup Guides and
Optional accessory
In-ceiling bracket YT-ICB45
Design and specications are subject to change without notice.
(AGC 36 dB, Light funnel ON)
readout), 0.01 lx (AGC 36 dB, Light funnel ON)
7
/8 inches)
7
/8 inches)
relay outputs electrically isolated from the
camera)
sync negative
Vrms
IEEE802.3af compliant (PoE system)
+122°F)
not including the projecting parts
cables and bracket
supplied programs) (1), Bracket (1), Template (1),
Wire rope (1), Camera unit mounting screws (4),
Shoulder screw M4 (1), Wrench (1), Audio
cable (1), I/O cable (1), LAN cable (1), BNC
cable (1), Power input cable (1), Installation
Manual (this document) (1 set), B&P Warranty
Booklet (1)
5
/8 inches × 4 3/4 inches),
Loading...