Sony SBV-60-S Service manual
SB-V60S
SERVICE MANUAL
Ver. 1.0 2005. 01
SPECIFICATIONS
Input S-VIDEO 4-pin mini DIN × 4
VIDEO PHONO jack × 4
AUDIO L/R PHONO jack × 4
(INPUT3 is switchable between
the front and rear panel)
Output S-VIDEO 4-pin mini DIN × 2
VIDEO PHONO jack × 2
AUDIO L/R PHONO jack × 2
Dimensions (approx.) 430 × 42 × 231 mm
(17 × 1 11/16 × 9 1/8 in.) (w/h/d)
including projecting parts
Mass (approx.) 2 kg (4 lb. 7 oz.)
Operating temperature 0 °C to 40 °C (32 °F to 104 °F)
Supplied accessories Operating Instructions (1),
Label (1), Warranty (1)
Design and specifications are subject to change without
notice.
US Model
Canadian Model
z UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
9-879-434-01
2005A04-1
© 2005. 01
AV SELECTOR
Sony Corporation
Personal Audio Company
Published by Sony Engineering Corporation
1
SB-V60S
SECTION 1
GENERAL
A
Front panel / Panneau avant / Panel frontal
Rear panel / Panneau arriere / Panel posterior
Locating the Parts and
Controls (see fig. A)
Front panel
1
INPUT SELECT buttons for MONITOR OUT
Press one of the INPUT 1 - 4 buttons to select
the input to be output to MONITOR OUT for
displaying on a TV or monitor, etc.
2
INPUT SELECT buttons for REC OUT
Press one of the INPUT 1 - 3 buttons to select
the input to be output to MONITOR OUT for
recording to a DVD/HDD recorder or VCR, etc.
3
REC OUT OFF button
Turn off all INPUT SELECT buttons for REC
OUT.
4
INPUT 3 FRONT/REAR button
Switches the effective INPUT3 jack between the
rear and front panels.
5
INPUT3 jack
S-VIDEO / VIDEO / AUDIO-L / AUDIO-R
Connect to the output jacks of a video game or
camcorder.
This section is extracted
from instruction manual.
Rear panel
1
MONITOR OUT jack
S-VIDEO / VIDEO / AUDIO-L / AUDIO-R
2
REC OUT jack
S-VIDEO / VIDEO / AUDIO-L / AUDIO-R
3
INPUT 1 - 4 jacks
S-VIDEO / VIDEO / AUDIO-L / AUDIO-R
How to use the supplied labels
To determine which device is connected where
without checking the rear panel, put labels on the
front panel of the unit. You can use plain labels
marked with an oil-based ink pen.
2
SECTION 2
DIAGRAMS
2-1. PRINTED WIRING BOARD — MAIN SECTION — : Uses unleaded solder.
SB-V60S
A
B
C
D
1
MAIN BOARD
R – AUDIO – L
C4 C3
(CHASSIS)
234567891011 12 13 14
MONITOR OUT
CN12
S-VIDEOVIDEO
CHASSIS
R – AUDIO – L
CN10
C2 C1
REC OUT
S-VIDEOVIDEO
CHASSIS
R – AUDIO – L
CN8CN11 CN9 CN7
INPUT 1
S-VIDEOVIDEO
CHASSIS
R – AUDIO – L
CN6 CN5
INPUT 2
S-VIDEOVIDEO
R – AUDIO – L
CHASSIS
INPUT 3
(REAR)
S-VIDEOVIDEO
CN4 CN3
INPUT 4
R – AUDIO – L
CN2 CN1
CHASSIS
S-VIDEOVIDEO
CHASSIS
(CHASSIS)
SB-V60S
E
F
G
H
(CHASSIS)
CN14 CN13
VIDEOR – AUDIO – L
INPUT 3
(FRONT)
S-VIDEO
2
4
5
3
FRONT
REAR
SW3
INPUT
2
4
1
3
6
87
10 9
(SW2-3)
3REC OUT OFF
SW2
REC OUT
1
1
3
3
5
5
7
9
2
4
(SW2-2)1(SW2-1)
2
INPUT
1
3
5
6
8
10
2
4
6
87
109
2
4
5
132
(SW1-4)3(SW1-3)
4
Common Note on Printed Wiring Boards:
• X : parts extracted from the component side.
• : Pattern from the side which enables seeing.
4
5
MONITOR OUT
132
INPUT
SW1
4
5
(SW1-2)
132
4
5
2
1
3
111-864-065-
(SW1-1)
1
Common Note on Schematic Diagrams:
• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
• C : panel designation.
• Signal path.
F : Audio
J : Chroma
c : Luminance
I : Video (Composite)
33
Loading...