Sony RMT-D254A, RDR-GX360 Service Manual

US Model

SERVICE MANUAL

DVD RECORDER

SPECIFICATIONS

RMT-D254A

RDR-GX360

Ver. 1.0 2008.03

System

[DVD recorder section]

Laser

Semiconductor laser

Audio recording form at

Dolby Digital

Video recording format

MPEG Video

[Timer section]

Clock

Quartz locked

Timer indication

12-hour cycle

Timer setting

12 programs (max.)

Inputs and outputs

LINE 1 IN and LINE 2 IN

VIDEO IN, phono jack (1 each) Input signal: 1 Vp-p, 75 ohms, unbalanced, sync negative AUDIO IN, phono jacks (2 each) Input level: 327 mVrms Input impedance: more than 47 kilohms S VIDEO, 4-pin, mini-DIN jack Y: 1.0 Vp-p, unbalanced, sync negative C: 0.286 Vp-p, load impedance 75 ohms DV IN, 4-pin jack, i.LINK S100

LINE OUT

VIDEO OUT, phono jack (1) Output signal: 1 Vp-p, 75 ohms, unbalanced, sync negative AUDIO OUT, phono jacks (2) Standard output: 327 mVrms Load impedance: 47 kilohms Output impedance: less than 10 kilohms

DIGITAL AUDIO OUT

COAXIAL, phono jack Output signal: 0.5 Vp-p, 75 ohms

COMPONENT VIDEO OU T (Y , P B, PR)

Phono jack Y: 1.0 Vp-p/P

, PR: 0.7 Vp-p, 75 ohms

SET TOP BOX CONTRO L

Mini jack

HDMI OUT

HDMI 19 pin-Standard Connector

USB

USB jack Type A (For connecting camcorders or digital still cameras)

General

Power requirements

120 V AC, 60 Hz

Power consumption

17 W

Power back-up

Back-up duration: 30 min

Operating temper at ure

5°C to 35°C (41°F to 95°F)

Storage temperat ur e

–20°C to 60°C (–4°F to 140°F)

Operating humidity

25% to 80%

Dimensions incl ud ing projecting parts and controls (w/h/d )

Approx. 430 × 59 × 225 mm (Approx. 17 × 2

/8 × 8 7/8 inches)

Mass

Approx. 2.4 kg (Approx. 5.3 lbs)

Supplied accessori es

Remote commander (remote) (1) Size AA (R6) batteries (2) Audio/video cord (1) Set top box controller (1)

Design and specifications are subject to change without notice.

— 2 —

WARNING!!

WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION, BE SURE TO OBSER VE FR OM A DIST ANCE OF MORE THAN 25 cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

CAUTION:

The use of optical instrument with this product will increase eye hazard.

Fig. A. Using an AC voltmeter to check AC leakage.

1.5 k

Ω

0.15 µF

AC voltmeter (0.75 V)

To Exposed Metal Parts on Set

Earth Ground

LEAKAGE TEST

The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes). Leakage current can be measured by any one of three methods.

1. A commercial leakage tester, such as the Simpson 229 or RCA

WT-540A. Follow the manufacturers' instructions to use these

instruments.

2. A battery-operated AC milliammeter. The Data Precision 245

digital multimeter is suitable for this job.

3. Measuring the volta ge drop across a resistor by means of a V OM

or battery-operated AC voltmeter. The “limit” indication is

0.75V , so analog meters must ha ve an accurate low-voltage scale.

The Simpson 250 and Sanwa SH-63Trd are examples of a

passive VOM that is suitable. Nearly all ba ttery operated digital

multimeters that have a 2V A C range are suitable. (See Fig. A)

1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges.

2. Check the interboard wiring to ensure that no wires are “pinched” or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.

4. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement.

5. Check the line cord for cracks and abrasion. Recommend the replacement of any such line cord to the customer.

6. Check the B+ voltage to see it is at the values specified.

7. Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer:

Unleaded solder

Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)

: LEAD FREE MARK

Unleaded solder has the following characteristics.

• Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful!

• Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc.

• Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.

— 3 —

TABLE OF CONTENTS

Precautions

1 Safety Precautions ······························································ 4 2 Servicing Precautions ························································ 6 3 ESD Precautions································································· 7 4 Handling the Optical Pick-up ·············································8

1. General

Ways to Use Your DVD Recorder ···································1-1 How to Use the On-Screen Menus ··································1-1 Hookups and Settings ······················································1-2 Quick Guide to Disc Types··············································1-6 Playback ··········································································1-7 Recording ······································································1-10 Editing ···········································································1-13 DV/D8 Dubbing (DV/D8 → DVD)·······························1-15 USB Dubbing (USB → DVD) ······································1-16 Settings and Adjustments ··············································1-18 Additional Information·················································· 1-21

2. Disassembly and Reassembly

2-1 Cabinet and PCB ····························································2-1 2-1-1 Cabinet Top Remov al·····················································2-1 2-1-2 Ass’y Front Panel Removal············································ 2-1 2-1-3 Chassis Removal ····························································2-2 2-2 Circuit Board Locations ·················································2-3

3. Block Diagram..........................................................3-1

4. PCB Diagrams

4-1 DVD Main PCB ······························································4-3 4-2 Jack PCB ·········································································4-7 4-3 Function PCB ·······························································4-11 4-4 Front PCB······································································ 4-13

5. Schematic Diagrams

5-1 S.M.P.S. (Jack PCB) ························································ 5-3 5-2 Power (Jack PCB)····························································5-5 5-3 AV Decoder (DVD Main PCB)·······································5-7 5-4 AV Link TS in_Out (DVD Main PCB) ···························5-9 5-5 Connector (DVD Main PCB) ········································5-11 5-6 DDR (DVD Main PCB) ················································5-13 5-7 HDMI CEC (DVD Main PCB) ·····································5-15 5-8 HDMI TDA9984 (DVD Main PCB) ·····························5-17 5-9 Host1 & Flash & Remulator I/F (DVD Main PCB)······5-19 5-10 IEEE1394_DV (DVD Main PCB)·································5-21 5-11 PCMIO & VIO & VDAC (DVD Main PCB) ················5-23 5-12 USB (DVD Main PCB) ·················································5-25 5-13 User Interface (DVD Main PCB) ··································5-27 5-14 Input_Output (Jack PCB) ··············································5-29 5-15 Connector (Jack PCB) ···················································5-31 5-16 Front Micom (Jack PCB) ··············································5-33 5-17 Function Timer (Function PCB)····································5-35 5-18 Front AV (Front PCB) ··················································· 5-37

6. Troubleshooting·················································6-1

7. Repair Parts List

7-1 Exploded Vie ws ·······························································7-2 7-2 Electrical Parts List ························································· 7-3

— 4 —

PRECAUTIONS

1 SAFETY PRECAUTIONS

1) Before returning an instrument to the customer, always make a safety check of the entire instrument, including, but not limited to, the following items:

(1) Be sure that no built-in protective devices are defecti ve or ha ve

been defeated during servicing. (1)Protective shields are provided to protect both the technician and the customer. Correctly replace all missing protective shields, including any removed for servicing convenience. (2)When reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place all protective devices, including, but not limited to, nonmetallic control knobs, insulating fish papers, adjustment and compartment covers/ shields, and isolation resistor/capacitor networks. Do not operate this instrument or permit it to be operated without all protective devices correctly installed and functioning.

(2) Be sure that there are no cabinet openings through which adults

or children might be able to insert their fingers and contact a hazardous voltage. Such openings include, but are not limited to, excessively wide cabinet ventilation slots, and an improperly fitted and/or incorrectly secured cabinet back cover.

(3) Leakage Current Hot Check-With the instrument completely

reassembled, plug the AC line cord directly into a 120V AC outlet. (Do not use an isolation transformer during this test.) Use a leakage current tester or a metering system that complies with American National Standards institute (ANSI) C101.1 Leakage Current for Appliances and Underwriters Laboratories (UL) 1270 (40.7). With the instrument’s AC switch first in the ON position and then in the OFF position, measure from a known earth ground (metal water pipe, conduit, etc.) to all exposed metal parts of the instrument (antennas, handle brackets, metal cabinets, screwheads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis. Any current measured must not exceed 0.5mA. Reverse the instrument power cord plug in the outlet and repeat the test. See Fig. 1. Any measurements not within the limits specified herein indicate a potential shock hazard that must be eliminated before returning the instrument to the customer.

(4) Insulation Resistance Test Cold Check-(1) Unplug the power

supply cord and connect a jumper wire between the two prongs of the plug. (2) Turn on the po wer switch of the instrument. (3) Measure the resistance with an ohmmeter between the jumpered AC plug and all exposed metallic cabinet parts on the instrument, such as screwheads, antenna, control shafts, handle brackets, etc. When an exposed metallic part has a return path to the chassis, the reading should be between 1 and 5.2 megohm. When there is no return path to the chassis, the reading must be infinite. If the reading is not within the limits specified, there is the possibility of a shock hazard, and the instrument must be repared and rechecked before it is returned to the customer. See Fig. 2.

DEVICE UNDER

TEST

(READING SHOULD

NOT BE ABOVE

0.5mA)

LEAKAGE CURRENT

TESTER

EARTH

GROUND

TEST ALL

EXPOSED METER

SURFACES

ALSO TEST WITH

PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)

2-WIRE CORD

Fig. 1 AC Leakage Test

Fig. 2 Insulation Resistance Test

2) Read and comply with all caution and safety related notes on or inside the cabinet, or on the chassis.

3) Design Alteration W arning-Do not alter or add to the mechanical or electrical design of this instrument. Design alterations and additions, including but not limited to, circuit modifications and the addition of items such as auxiliary audio output connections, might alter the safety characteristics of this instrument and create a hazard to the user. Any design alterations or additions will make you, the servicer, responsible for personal injury or property damage resulting therefrom.

4) Observe original lead dress. Take extra care to assure correct lead dress in the following areas: (1) near sharp edges, (2) near thermally hot parts (be sure that leads and components do not touch thermally hot parts), (3) the AC supply, (4) high voltage, and (5) antenna wiring. Always inspect in all areas for pinched, out-of-place, or frayed wiring, Do not change spacing between a component and the printedcircuit board. Check the AC power cord for damage.

5) Components, parts, and/or wiring that appear to have overheated or that are otherwise damaged should be replaced with components, parts and/or wiring that meet original specifications. Additionally, determine the cause of o verheating and/or damage and, if necessary, tak e corrective action to remo ve any potential safety hazard.

Antenna Terminal

Exposed Metal Part

ohm

ohmmeter

— 5 —

6) Product Safety Notice-Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection, nor can the protection they giv e necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by shading, an ( ) or a ( ) on schematics and parts lists. Use of a substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire and/or other hazards. Product safety is under review continuously and new instructions are issued whenever appropriate.

— 6 —

2 SERVICING PRECAUTIONS

CAUTION: Before servicing units co v ered b y this service manual and its supplements, read and follow the Safety Precautions section of this manual.

Note: If unforseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions. Remember: Safety First.

2-1 General Servicing Precautions

(1) a. Always unplug the instrument’s A C po wer cord from the AC

power source before (1) re-moving or reinstalling any component, circuit board, module or any other instrument assembly, (2) disconnecting an y instrument electrical plug or other electrical connection, (3) connecting a test substitute in parallel with an electrolytic capacitor in the instrument.

b. Do not defeat any plug/socket B+ voltage interlocks with

which instruments covered by this service manual might be equipped.

c. Do not apply AC power to this instrument and/or any of its

electrical assemblies unless all solid-state device heat sinks are correctly installed.

d. Always connect a test instrument’s ground lead to the

instrument chassis ground before connecting the test instrument positive lead. Always remove the test instrument ground lead last.

Note: Refer to the Safety Precautions section ground lead last.

(2) The service precautions are indicated or printed on the cabinet,

chassis or components. When servicing, follow the printed or indicated service precautions and service materials.

(3) The components used in the unit have a specified flame

resistance and dielectric strength. When replacing components, use components which have the same ratings. Components identified by shading, by ( ) or by ( ) in the circuit diagram are important for safety or for the characteristics of the unit. Always replace them with the exact replacement components.

(4) An insulation tube or tape is sometimes used and some

components are raised above the printed wiring board for safety . The internal wiring is sometimes clamped to prevent contact with heating components. Install such elements as they were.

(5) After servicing, always check that the removed screws,

components, and wiring have been installed correctly and that the portion around the serviced part has not been damaged and so on. Further, check the insulation between the blades of the attachment plug and accessible conductive parts.

2-2 Insulation Checking Procedure

Disconnect the attachment plug from the AC outlet and turn the power ON. Connect the insulation resistance meter (500V) to the blades of the attachment plug. The insulation resistance between each blade of the attachment plug and accessible conductive parts (see note) should be more than 1 Megohm.

Note: Accessib le conductive parts include metal panels, input terminals, earphone jacks, etc.

— 7 —

3 ESD PRECAUTIONS

Electrostatically Sensitive Devices (ESD)

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated circuits and some field-effect transistors and semiconductor chip components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity.

(1) Immediately before handling any semiconductor component or

semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test.

(2) After removing an electrical assembly equipped with ESD

devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

(3) Use only a grounded-tip soldering iron to solder or unsolder

ESD devices.

(4) Use only an anti-static solder removal devices. Some solder

removal devices not classified as “anti-static” can generate electrical charges sufficient to damage ESD devices.

(5) Do not use freon-propelled chemicals. These can generate

electrical charges sufficient to damage ESD devices.

(6) Do not remove a replacement ESD device from its protective

package until immediately before your are ready to install it. (Most replacement ESD devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive materials).

(7) Immediately before removing the protective materials from the

leads of a replacement ESD device, touch the protective mater ial to the chassis or circuit assembly into which the device will be installed.

CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

(8) Minimize bodily motions when handling unpackaged

replacement ESD devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ESD device).

— 8 —

4 HANDLING THE OPTICAL PICK-UP

The laser diode in the optical pick up may suffer electrostatic breakdown because of potential static electricity from clothing and your body.

The following method is recommended. (1) Place a conductive sheet on the work bench (The black sheet

used for wrapping repair parts.)

(2) Place the set on the conductive sheet so that the chassis is

grounded to the sheet.

(3) Place your hands on the conductive sheet (This gives them the

same ground as the sheet.)

(4) Remove the optical pick up block

(5) Perform work on top of the conductive sheet. Be careful not to

let your clothes or any other static sources to touch the unit.

◆ Be sure to put on a wrist strap grounded to the sheet.

◆ Be sure to lay a conductive sheet made of copper etc. Which is

grounded to the table.

Fig.3

(6) Short the short terminal on the PCB, which is inside the Pick-

Up ASS’Y, before replacing the Pick-Up. (The short terminal is shorted when the Pick-Up Ass’y is being lifted or mov ed.)

(7) After replacing the Pick-up, open the short terminal on the PCB.

THE UNIT

WRIST-STRAP FOR GROUNDING

CONDUCTIVE SHEET

1-1

1. GENERAL

This section is extracted from instruction manual. (3-296-710-11)

RDR-GX360

Ways to Use Your DVD Recorder

Recording and timer recording

, Record TV programs on a DVD, either

manually or using the timer. You need to connect a tuner such as a cable box to this recorder.

Control your cable box or satellite receiver – Set top box control

, Connect the supplied set top box controller

to have the recorder change the channel of your cable box or satellite receiver (page 13).

Quick access to recorded titles – Title List

, Display the Title List to view all titles on a

disc and select a title for playback or editing.

103

LINE 2 IN DV IN

ONE-TOUCH DUBBING

REC

VIDEO

(MONO)

AUDIO R

CH 103!

Title List

10:10 AM

LINE 1

08:00 PM

May/02/2008

No.1/4

Title Length Edit

LINE 1 01:29:03

LINE 1 00:31:23

LINE 1 01:59:00

LINE 1 00:58:56

Title List (Original)

Creating your own program – Playlist

, Record a program on a DVD-RW (VR

mode) or DVD-R (VR mode), then erase, move or add scenes as you like without changing the original con tents.

Dubbing(DV/USB t DVD)

, Connect your DV camcorder or USB

device to the recorder to dub video or photo contents to a DVD.

Playing JPEG image files or MP3 audio files

, You can enjoy viewing JPEG images on

your TV screen. First, take pictures with a digital camera and save them in JPEG format to a DATA CD (CD-RW/CD-R) or DATA DVD (DVD+RW/DVD-RW/ DVD+R/DVD-R) on a PC. Then play the disc on this recorder (page 41). You can also play MP3 audio files on th is recorder (page 41).

A list of recordable and playable discs is on page 30.

Original

Playlist

REC

i.LINK cable

Dubbing

USB cable

L I

N E 2 I

D V I

O N E

T O U C H D U B B I

N G

R E C

V I

D E O L (

M O N O )

A U D I

O R

Shoot

Save

Play!

How to Use the On-Screen Menus

The following three displays are mainly used to operate this recorder. Once you become familiar with the basic operations, you will find the recorder easy to use.

System Menu

The System Menu appears when y ou press SYSTEM MENU, and provides entr ies to all of the recorder’s main functions, such as timer recording and setup. Selectable options on the System M enu differ depending on the media t ype, disc condition, and operating status.

Select an option by pressing M/m an d ENTER.

A “Title List”

Displays the list of the disc contents, including the recording informati on and movie thumbnail image, which allows you to select a title to play or edit.

B “Timer”

Used to set a new timer recording as well as change or cancel the timer recordings you set.

C “Edit”

Used to create or edit a Playlist (unfinalized DVD-RWs (VR mode)/DVD-Rs (VR mode) only).

D “Dubbing”

Used to dub from a DV/D8 format tape or a USB device to a disc.

E “Disc Setting”

Used to rename, protect, format, or finalize a disc, or erase all titles on the disc. Also, displays the disc information.

F “Setup”

Displays the “Setup” dis play for setting up the recorder to suit your preferences.

M/m/</,, ENTER

SYSTEM

OPTIONSO RETURN

11 22 33

44 55 66

77 880099

Title List (Original)

10:10 AM

Press ENTER :

Title Menu for DVD Title List.

Setup

Disc Setting

Edit

Title List

Timer

Dubbing

10:10 AM

01 LINE 1 >01:29:03

02 LINE 1 >00:31:23

03 LINE 1 >01:59:00

04 LINE 1 >00:58:56

LINE

08:00 PM

May/02/2008

No. Title Length Edit

Title List (Original)

1/4

Sub-menu

The sub-menu appears when yo u select an item from a list menu (e.g., a title from the Title List menu), and press ENTER. The sub-menu d isplays options applicable only to the selected item. Th e displayed options differ depending on the situation and disc type. Select an option by pressing M/m and ENTER.

Example: The Title List menu

OPTIONS

The OPTIONS menu appears when you press OPTIONS. You can search for a title/chapter/ track, check the playing and remaining time, or change settings for audio/angle/subtitle. The displayed options differ depending on the media type. Press M/m to select an option, press </, to select the desired item, and press ENTER.

Example: When you press OPTIONS while a DVD VIDEO is playing.

To return to the previous display

Press O RETURN.

Notes

•The OPTIONS menu settings cannot be changed during DVD recording.

•The System Menu does not appear when recording on a DVD.

Title List (Original)

10:10 AM

No. Title Length Edit

01 LINE 1 >01:29:03

02 LINE 1 >00:31:23

03 LINE 1 >01:59:00

04 LINE 1 >00:58:56

LINE 1 May/02/2008

08:00 PM

1/4

Play

Title Erase

Chapter Erase

Protect

Title Name

A·B Erase

Divide Title

Options for the selected item

1/4

1/1

00:00:25

Title

Chapter

Time

Remain

Audio

Angle

00:01:30

Subtitle

2/2 ENG

1/1

ENG Dolby D2ch (1/1)

DVD VIDEO

1-2

Hookups and Settings

Hooking Up the Recorder

Follow steps 1 to 7 to hook up and adjust the settings of the recorder.

Notes

•Plug cords securely to prevent unwanted noise.

•See the instructions supplied with the components to be connected.

•You cannot connect this recorder to a TV t hat does not have a video input jack.

•Be sure to disconnect the power cord of each component before connecting. Do not co nnect the power cord until you reach “Connecting the Power Cord” on page 20.

Step 1: Unpacking

Check that you have the following items:

•Audio/video cord (phono plug u 3 y phono plug u 3) (1)

•Remote commander (remote) (1)

•Set top box con troller (1)

•Size AA (R6) batteries (2)

Step 2: Connecting the Cable Box/Satellite Receiver (Tuner)

This recorder does not include a TV tuner. To record TV programs on this recorder, you need to connect the recorder to a tuner that has audio/ video output jacks. If you have been using your VCR co nnected to an antenna, connect this recorder to your VCR using an audio/video cord. In this way, you will b e able to record TV programs.

You cannot record on this recorder if you have: –a cable box or satellite receiver without audio/

video outputs. –cable with no cable box. –antenna only (no cable TV). In the cases above, contact your cable service or satellite service company to see if they can provide you with a compatible cable box or satellite receiver.

Using the cable box/satellite receiver control function

This function allows the recorder to control a cable box or satellite receiver via the supplied set top box controller. You can also use the recorder’s remote control to change channels on the cable box/satellite receiver whenever the cable box/ satellite receiver and the recorder are turned on. To use the cable box/satellite receiver control function, you need to: –Check the brand code of your cable box/sa tellite

receiver. See “Cable Box/Satellite Receiver

Brand Code” (page 101). –Connect the set top box controller (page 1 3). –Set the brand code number and t he recorder’s

input that is connected to the cable box/sa tellite

receiver (page 23). After setting up the cable box/satellite receiver control, check that the recorder can correctly control the cable box or satellite receiver (page 25).

Hookups and Settings

Connecting a cable box/satellite receiver and set top box controller

Connect the LINE 1 IN jacks using an aud io/video cord. With this hookup, you can record any channel on the cable box or satellite receiver. Be sure that the cable box or satellite receiver is turned on. You need to connect to the LINE 1 IN (VIDEO/AUDIO) jacks for the Synchro-Rec function (page 54). To record cable or satellite programs, you need to match the input source on the recorder (LINE1) to the input jack connected to the cable box or satellite re ceiver (LINE 1 IN). Place the set top box controller ne ar the remote sensor on the cable box/satellite receiver.

To use an S video cor d for enjoying higher quality images

Connect the LINE 1 IN S VIDEO jack using an S video cord (not supplied) instead of the yellow (video) plug of the audio/video cord. Leave the audio plugs connected to the AUDIO L/R jacks. When using this connection, be sure to set “Line1 Input” to “S-Video” in the “Video” setup (page 81). You cannot use the Synchro-Rec function with this connection.

ANT IN

AUDIO

OUT

S VIDEO

OUT

VIDEO

OUT

TO TV

Set top box controller (supplied)

Cable box/ satellite receiver

Antenna cable (not supplied)

Wall

to antenna input

Audio/video cord (not supplied)

to SET TOP BOX CONTROL

to LINE 1 IN

DVD recorder

: Signal flow

to LINE 1 IN S VIDEO

S video cord (not supplied)

,continued

z Hint

You can also connect a cable box/satellite receiver to the LINE 2 IN jacks on the front panel. In this case, select “Line2” for “Connections” of “Set Top Box Control” in the “Features” setup (page 85).

Notes

•Do not connect to the S VIDEO and yellow VIDEO jacks at the same time.

•Sync hro-Recording does not work with some tuners. For details, see the tuner’s operating instructions.

Hookups and Settings

Step 3: Connecting to Your TV

Connect the supplied audio/vide o cord to the LINE OUT (VIDEO/AUDIO L/R) jacks of the r ecorder. If your TV has an HDMI jack, or component video input jacks, see page 16 or 17.

When playing “wide screen” imag es

Some recorded images may not fit your TV screen. To change the picture size, see page 80.

Note

Do not connect your TV’s audio output jacks to the LINE IN (AUDIO L/R) jacks at the same time. This will cause unwanted noise to come from your TV’s speakers.

AUDIO

INPUT

RLVIDEO

: Signal flow

TV or projector

(red) (white) (yellow)

Audio/video cord (supplied)

(red)

(white)

(yellow)

DVD recorder

to LINE OUT (VIDEO/AUDIO L/R)

,continued

1-3

If your TV has an HDMI input jack

Connect the HDMI* OUT jack using a c ertified Sony HDMI cord (not supplied). You will enjoy high quality picture and sound. If your TV accepts progressive 1080p format signals, you mus t use this connection. The HDMI indicator i s lit in the front panel display when the recorder outputs si gnals through the HDMI OUT jack. Be sure to turn off the recorder before connecting an HDMI cord.

*This DVD recorder incorporates High-Definition Multimedia Interface (HDMI™) technology. HDMI, the HDMI

Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

Using the Control for HDMI functions for ‘BRAVIA’ Sync (for HDMI connections only)

By connecting Sony components that are compatible with the Control for HDMI function with an HDMI cord (not supplied), operation is simplified as below:

•One-Touch Play (page 38)

•System Power-Off

When you turn the TV off by using the "/1 button on the TV’s remote, the components compatible with the Control for HDMI function turn off automatically.

To prepare for th e ‘BRAVIA’ Sync features

Set “Control for HDMI” to “On” in the “Features” setup (page 85). For details on TV sett ings, refer to the operating instructions supplied with the TV.

Notes

•You ca nnot connect the HDMI OUT jack to DVI jacks that are not HDCP compliant (e.g., DVI jacks on PC displays).

•Depending on the connected compo nent, the Control for HDMI function may not work. Refer to the operating instructions supplied with the component.

•The reco rder supports only the playback option of Control for HDMI. “Player” appears on the TV screen when using the Control for HDMI functions.

HDMI IN

TV or projector

HDMI cord (not supplied)

to HDMI OUT

: Signal flow

DVD recorder

to HDMI input

Hookups and Settings

If your TV has component video input jacks

Connect the COMPONENT VIDE O OUT jacks using a component video cord (not supplied) or three video cords (not supplied) of the same kind and length. You will enjoy accurate color reproduction and high quality images. If your TV accepts progressive 480p form at signals, you must use this connection and then set “Progressive” of “Video” to “O n” in the “Setup” display (page 81). The P ROGRESSIVE indicator lights up when the recorder output s progressive signals. When using this connection, be sure to connect the audio cord to the LINE OUT (AUDIO L/R) jacks.

COMPONENT VIDEO IN

PBP

AUDIO

INPUT

: Signal flow

TV or projector

(red)(white) (green)

Component video cord (not supplied)

(red) (blue)

(red)

(green)

(blue)

to COMPONENT VIDEO OUT

Audio/video cord (supplied)

(white)

(red)

to LINE OUT (AUDIO L/R)

DVD recorder

Step 4: Connecting to Your AV Amplifier (Receiver)

Select one of the following patte rns A or B, according to the input jack on your AV amplifier (receiver). This will enable you to listen to soun d through your AV amplifier (receiver).

AUDIO

INPUT

: Signal flow

AV amplifier (receiver)

(red)

(white)

Audio cord (not supplied) (white)

(red)

DVD recorder to AUDIO OUT (L/R)

to DIGITAL AUDIO OUT (COAXIAL)

Coaxial digital cord (not supplied)

[Speakers]

Rear (L)

Front (L)

Center

to coaxial digital input

[Speakers]

Rear (R)

Front (R)

Subwoofer

AV amplifier (receiver) with a decoder

Hookups and Settings

A Connecting to audio L/R jacks

This connection uses a stereo amplifier’s (receiver’s) two front speakers for sound.

You can enjoy the surround function that creates virtual speakers from two st ereo speakers. Select “Surround1,” “Surround2 ,” or “Surround3” in “Surround” of the “Audio” set up (page 83).

Surround 1

Surround 2

Surround 3

Note

Make sure that your listening position is between and at an equal distance from your speakers, and that the speakers are located in similar surroundings.

B Connecting to a digital audio input jack

Use this connection if your AV amplifier (receiver) has a Dolby*1 Digital or DTS*2 decoder and a digital input jack. You can enjoy the surround effect of Dolby Digital (5.1ch ) or DTS (5.1ch). After you have completed the connection, make the appropriate settings under the “Audio” setup (page 82). Otherwise, no sound or a loud noise will come from your speakers.

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

Manufactured under license under U.S. Patent #: 5,451,942 & other U.S. and worldwide patents iss ued & pending. DTS and DTS Digital Out are registered trademarks and the DTS logos and Symbol ar e trademarks of DTS, Inc. © 1996-2007 DTS, Inc. All Rights Reserved.

z Hints

•For correct speaker location, see the operating instructions supplied with the connected components.

•With a coaxial digital connection, you cannot: –use the virtual surround effects of this recorder. –switch the bilingua l sounds on a DVD-RW/DVD-R

(VR mode) by pressing AUDIO when you set “Dolby Digital” to “Dolby Digital” in t he “Audio” setup (page 82).

Virtual speaker

1-4

Step 5: Connecting the Power Cord

Plug the recorder and TV powe r cords into an AC outlet. After you connect the power cord, you

must wait for a short while before operating the recorder. You can opera te the

recorder only after the front panel display lights up and the recorder enters standb y mode. If you connect additional equipm ent to this recorder (page 27) , be sure to connect the po wer cord only after all connections are complete.

Step 6: Preparing the Remote

You can control the recorder using the supplied remote. Insert two size AA (R6) batteries by matching the 3 and # ends on the batteries to the markings inside the battery compartment. Be sure to close the battery cover properly. When using the remote, point it at the remote sensor on the recorder.

Notes

• If the supplied remote interferes your other Sony DVD recorder or player, change the command mode number for this recorder (page 22).

•Use the batteries correctly to avo id possible leakage and corrosion. Do not touch the liquid with bare hands should leakage occur. Observe the following: –Do not use a new battery wit h an old battery, or

batteries of different manufacturers. –Do not attemp t to recharge the batteries. –If you do not intend to us e the remote for an extended

period of time, remove the batteries. –If batt ery leakage occurs, wipe out any liquid inside

the battery compartment, and insert n ew batteries.

•Do not e xpose the remote sensor (marked on the front panel) to strong light, such as direct sunlight or lighting apparatus. The recorder may not respond to t he remote.

•With normal use, the batteries should last about three to six months.

•Do not leave the remote in an extremely hot or hu mid place.

•Do not d rop any foreign object into the remote casing, particularly when replacing the batteries.

to AC outlet <

Hookups and Settings

Controlling TVs with the remote

You can adjust the remote control ’s signal to control your TV.

Notes

•Depending on the TV, some or all of the bu ttons below may not work for the TV.

• If y ou enter a new code number, the code number previously entered will be erased.

•When you replace the batteries of the remote, the code number may be reset to the default setting. Set the appropriate code number again.

1 Hold down TV "/1 located at the bottom of

the remote.

Do not press "/1 at the top of the remote.

2 With TV "/1 pressed down, enter your

TV’s manufacturer code (see below) using the number buttons.

3 Release TV "/1.

The following buttons are for TV.

Code numbers of controllable TVs

If more than one code number is listed, try entering them one at a time until you find the one that works with your TV.

Press To

TV "/1 Turn your TV on or off

TV VOL +/– Adjust the volume of

your TV

TV CH +/– Select the channel on

your TV

11 22 33

44 55 66

77 880099

TV "/1

TV VOL +/–

TV INPUT

TV CH +/–

TV DIGITAL/ ANALOG

Number buttons

TV INPUT Switch your TV’s input

source

TV DIGITAL/ ANALOG

Select the broadcast on a Sony TV that can sw itch between digital and analog

Manufacturer Code number

Sony 01 (default)

Akai 04

AOC 04

Centurion 12

Coronado 03

Curtis-Mathes 12, 14

Daewoo 04, 22

Daytron 03, 12

Fisher 11

General Electric 04, 06, 10

Hitachi 02, 03, 04

J.C.Penney 04, 10, 12

JVC 09

KMC 03

LG/Gold Star 03, 04, 17

Magnavox 03, 04, 08, 12, 21

Marantz 04, 13

MGA/Mitsubishi 04, 12, 13, 17

NEC 04, 12

Panasonic 06, 19

Philco 02, 03, 04, 08

Philips 08, 21

Pioneer 06, 16

Portland 03

Proscan 10

Quasar 06, 18

Radio Shack 05, 10, 14

RCA 04, 10

,continued

If you have a Sony DVD player or more than one Sony DVD recorder

If the supplied remote interferes with your other Sony DVD recorder or player, set the co mmand mode number for this recorder and the supplied remote to one that differs from the other Sony DVD recorder or player, after you have completed “Step 7: Easy Setup.” The default command mode setting for this recorder and the supplied remote is DVD 3.

Check that Easy Setup (page2 3) has been finished. If Easy Setup has not been finished, first perform Easy Setup.

Press SYSTEM MENU.

The System Menu appears.

Select “Setup,” and press ENTER.

Select “Options,” and press ENTER.

Select “Command Mode,” and press ENTER.

Select a command mode (“DVD 1,” “DVD 2,” or “DVD 3”), and press ENTER.

Sampo 12

Samsung 03, 04, 12, 20

Sanyo 11, 14

Scott 12

Sears 07, 10 , 11

Sharp 03, 05, 18

Sylvania 08, 12

Teknika 03, 08, 14

Toshiba 07, 18

Wards 03, 04, 12

Yorx 12

Zenith 14, 15

Manufacturer Code number

11 22 33

44 55 66

77 880099

SYSTEM

M/m/</,, ENTER

O RETURN

10:10 AM

Clock Set

Video

Audio

Features

Options

Easy Setup

Setup

Disc Setting

Edit

Title List

Timer

Dubbing

Setup

No Disc

Options

Language

Parental

Front Display

Command Mode

Factory Setting

: Auto

: DVD 3

10:10 AM

Setup

Disc Setting

Edit

Title List

Timer

Dubbing

No Disc

Options

Language

Parental

Front Display

Command Mode

Factory Setting

: Auto

: DVD1 No

10:10 AM

Setup

Disc Setting

Edit

Title List

Timer

Dubbing

No Disc

DVD 1

DVD 2

DVD 3

Hookups and Settings

7 Set the command mode for the remote so it

matches the command mode for the recorder you set above.

Follow the steps below to set the command mode on the remote.

A Hold down ENTER.

B While holding down ENTER, enter the

command mode code number usi ng the number buttons.

C Hold down both the number buttons and

ENTER at the same time for more than three seconds.

To return to the previous display

Press O RETURN.

To check the command mode for the recor der

Press x (stop) on the recorder when the recorder is turned off. The command mode for the reco rder appears in the front panel display.

Step 7: Easy Setup

Follow the steps below to make the minimum number of basic adjustments for using the recorder. Settings are made in the following order.

1 Turn on the TV. 2 Press "/1.

The recorder turns on.

Command Mode Code number

DVD1 number button 1

DVD2 number button 2

DVD3 number button 3

If the command mode for the recorder has not been changed, set the command mode for the remote to the default setting of DVD3. If the command mode for the remote is changed to DVD1 or DVD2, you will be unable to operate this recorder.

OSD Language Setup

Cable Box/Sat. Control Setup

Clock Setup

TV Type Setup

Finished!

11 22 33

44 55 66

77 880099

M/m/</,, ENTER

O RETURN

"/1

Number buttons

,continued

1-5

3 Switch the input selector on your TV so th at

the signal from the recorder appears on your TV screen.

“Initial settings necessary to operate the DVD recorder will be made. You can change them later using setup.” appears.

•If this message does not appear, select “Easy Setup” in the “Setup” display to run Easy Setup (page 88).

4 Press ENTER.

The setup display for selecting the language used in the on-screen display ap pears.

5 Select a language, and press ENTER.

The setup display for cable box/sa tellite receiver control appears.

6 Select whether or not you use the cable

box/satellite receiver cont rol, and press ENTER.

If you want to use the cable box/satellite receiver control (page 12), sel ect “Yes.” If not, select “No,” then go to step 9.

7 Press the number buttons to enter the

brand code of your cable box/satellite receiver.

See “Cable Box/Satellite Receiver Brand Code” (page 101).

•To re-enter the code number, select “Cancel” and return to step 6.

8 Select “OK,” and press ENTER.

The setup display for clock setting appears.

9 Press M/m to set the month and pr ess ,.

Set the day, year, hour, minutes, and AM/PM in the same way, then press ENTER. The day of the week is set automatically. The setup display for selecting the picture size of the connected TV appears.

Select the setting that matches your TV type.

“16:9”: For wide-screen TVs or TVs with a wide screen mode. “4:3 Letter Box”: For 4:3 screen TVs. Displays “wide screen” picture s with bands on the upper and lower sections of the screen. “4:3 Pan Scan”: For 4:3 screen TVs. Automatically displays “wide screen” pictures on the entire screen and cuts off the sections that do not fit. For details, see “Video Settings (Video)” on page 80.

English

Français

Español

Easy Setup

Select the screen language.

No Disc

Do you want to control your set top box with this recorder? (Changes to the current setting will

erase all timer settings.)

Yes

Easy Setup

No Disc

Easy Setup

No Disc

OK Cancel

Enter the brand code of

your set top box.

Hour Min

AM/PM

Month

Set the time and date manually.

Day Year

00 AM12 :

01 2008 Tue

No Disc

Easy Setup

12:00 AM

Easy Setup

Select your TV screen type.

10:10 AM

No Disc

16 : 9

4 : 3 Letter Box

4 : 3 Pan Scan

Hookups and Settings

Press ENTER.

Press ENTER when “Finish” appears.

Easy Setup is finished. All connections and setup operations are complete. If you use the cable box/satellite receiver control, check that the co ntrol works correctly (page 25).

To return to the previous display

Press O RETURN.

z Hint

If you want to run Easy Setup again, select “Easy S etup” in the “Setup” display (page 88).

Note

To record TV programs using the timer, you m ust set the clock accurately.

Checking the cable box/satellite receiver control setting

1 Turn on the recorder and the cable box/

satellite receiver.

2 Point the recorder’s remote at the recorder

(not at the cable box/satellite receiver).

3 Press CH +/– and check that the channel

changes on the cable box/satellite receiver window.

4 Press the number buttons and check that

the channel changes on the cable box/ satellite receiver window.

If you cannot get the recorder to control your cable box/satellite receiver

Check the settings at “Set Top Box Control” in the “Features” setup (page85). Check the connection and place the set top box controller near the cable box/satellite receiver (page 12). If your cable box or satellite rec eiver still does not operate with this recorder, contact your cable or satellite company to see if they can provide you with a compatible cable box or satellite receiver.

To fix the set top box controller to your cable box/satellite receiver

Once you have confirmed that the set top box controller controls your cable box or satellite receiver, affix it in place.

1 Attach the supplied double-sided tape to the

set top box controller. Remove the backings on the double-sided tape.

Finish

Easy Setup

Easy Setup is finished.

10:10 AM

No Disc

,continued

2 Affix it so that the set top box controller is

near the remote control sensor on your cable box/satellite receiver.

LINE 2 IN DV IN

ONE-TOUCH

DUBBING

REC

VIDEO

(MONO)

AUDIO R

Hookups and Settings

Connecting a VCR or Similar Device

After disconnecting the recorder’s power cord from an AC outlet, connect a VCR or similar recording device to the LINE IN jacks of this recorder. Also refer to the operating instructions supplied with the connected equipment. If you connect equipment that has a timer function, you can use the Synchro Rec function (page54). In this case, connect the equipment to the LINE 1 IN (VIDEO/AUDIO) jacks (page 13). For connection to the DV IN or USB jack on the front panel, see page 68 or 71.

Connecting to the LINE 2 IN jacks on the front panel

Connect a VCR or similar device to the LINE 2 IN jacks of this recorder. You can connect a second DVD player and record DVDs.

z Hints

•When the connected equipment outputs only monaural sound, connect an audio cord to the white LINE IN AUDIO L (mono) jack.

•To record from connected equipment, select an input source (LINE1 or LINE2) to match the jack you connected to (page 56).

LINE 2 IN DV IN

ONE-TOUCH DUBBING

REC

VIDEO

(MONO)

AUDIO R

AUDIO

VIDEO

OUTPUT

LINE 2 IN VIDEO

(MONO)

AUDIO R

VCR, etc.

Audio/video cord (not supplied)

DVD recorder

to LINE 2 IN

: Signal flow

,continued

1-6

Notes

•Do not connect more than one type of video cord between the recorder and your TV at the same time.

•Pic tures containing copy protection signals that prohibit any copyi ng cannot be recorded. You cannot dub from DVD VIDEOs to this recorder.

•Do not connect the output jack of this recorder to another equipment’s input jack with the other equipmen t’s output jack connected to the input jack of this recorder. Noise (feedback) may result.

• If you pas s the recorder signals via the VCR, you may not receive a clear image on your TV screen.

Be sure to connect your VCR to the DVD recorder and your TV in the order shown below. To watch video tapes, watch the tapes through a second line input on your TV.

VCRDVD recorder TV

VCR DVD recorder TV

Line input 1

Line input 2

Quick Guide to Disc Types

Recordable and Playable Discs

Usable disc versions (as of Dec ember 2007)

•8×-speed or slow er DVD+RWs

•6×-speed or slower DVD-RWs (Ver.1.1, Ver.1.2 with CPRM

)

•16×-speed or slower DVD+Rs

•16×-speed or slower DVD-Rs (Ver.2.0, Ver.2.1 with CPRM)

•8×-speed or s lower DVD+R DL (Double Layer) discs

Discs that cannot be recorded on

•8 cm discs

•DVD-RAMs

“DVD+RW,” “DVD-RW,” “DVD+R,” “DVD+R DL,” and “DVD-R” logos are trademarks.

Disc Type

Disc Logo

Icon used in this manual

Formatting (new discs)

Compatibility with other DVD players (finalizing)

DVD+RW

Automatically formatted

Playable on DVD+RW compatible players (automatically finalized)

DVDRW

VR mode

Format in VR mode*2 (page 48)

Playable only on VR mode compatible players (finalization unnecessary) (page 66)

Video mode

Format in Video mode

(page 48)

Playable on most DVD players (finalization necessary) (page 66)

DVD+R

Automatically formatted

Playable on DVD+R compatible players (finalization necessary) (page 66)

DVD+R DL

DVDR

VR mode

Format in VR mode using the “Disc Setting” display (page 64)

Playable only on DVD-R VR mode compatible players (finalization necessary) (page 66)

Video mode

Automatically formatted in Video mode

Playable on most DVD players (finalization necessary) (page 66)

Video

Quick Guide to Disc Types

CPRM (Content Protection for Recor dable Media) is a coding technology that protects copyrights for images.

Unused DVD-RWs are automatically formatted according to the setting of “Format DVD-RW” in “Features” setup (page 85).

Erasing titles only frees up disc space if you erase the last title.

Erasing titles or chapters frees up disc space.

Erasing titles or chapters does not free up disc space.

When using DVD+R DL (Double Layer) discs, see the instructions supplied with the discs.

For DVD-RWs (Video mode), DVD-Rs (Video mode), and DVD+Rs, the Auto Finalize function is available (page 67).

Recording Features Editing Features

Rewrite (page 64)

Auto Chapter (page 50)

Change Title Name (page 61)

Erase Title/ Chapter (page 58)

A-B Erase (page 59)

Divide Title (page 60)

Playlist (page 62)

Yes Ye s YesYes/No*3Yes Ye s No

Yes Ye s YesYes/Yes*4Yes Ye s Yes

Yes Ye s YesYes/No*3No No No

No Yes Yes Yes/No*5No No No

No Yes Yes Yes/Yes*5Yes Ye s Yes

No Yes Yes Yes/No*5No No No

Playable Discs

“DVD VIDEO” and “CD” logos are trademarks.

MP3 (MPEG1 Audio Layer 3) is a standard format defined by ISO/MPEG which compresses audio data.

A logical format of files and folders on DATA-CDs, defined by ISO (International Organization for Standardization).

Discs that cannot be played

•CD-ROMs/CD-Rs/CD-RWs that are not recorded in music CD or Video CD format, or do not contain MP3 audio tracks or JPEG image files.

•Data part of CD-Extras

•DVD-ROMs that are not recorded in DVD Video format, or do not contain MP3 audio tracks or JPEG image files.

•DVD Audio discs

•HD layer on Super Audio CD s

•DVD VIDEOs with a different region code (see page 33)

•A disc recorded in a color system other than NTSC, such as PAL or SECAM

•A disc recorded in AVCHD format

Disc Type Disc Logo

Icon used in this manual

Characteristics

DVD VIDEO

Discs such as movies that can be purchased or rented

DVD-RAM —

DVD-RAMs recorded by another recording device. 12 cm discs without cartridges, or removable from their cartridges can be played.

VIDEO CD

VIDEO CDs or CD-Rs/CD-RWs in VIDEO CD format (with PBC function)

Music CDs or CD-Rs/CD-RWs in music CD format that can be purchased

DATA CD

CD-ROMs/CD-Rs/CD-RWs created on a PC or similar device in music format, or MP3

JPEG format that conforms to ISO9660

Level

1/Level 2

DATA DVD —

DVD-ROMs/DVD+RWs/DVD-RWs/DVD+Rs/ DVD-Rs in MP3*1 or JPEG format conforming to Universal Disk Format (UDF)

8 cm DVD+RW/ DVD-RW/DVD-R

——

8 cm DVD+RWs, DVD-RWs, and DVD-Rs recorded with a DVD video camera (Still images recorded with a DVD video camera cannot be played.)

DVD

RAM

VCD

DATA CD

DATA DVD

1-7

Quick Guide to Disc Types

Note on playback operations of DVD VIDEOs/ VIDEO CDs

Some playback operations of DVD VIDEOs/ VIDEO CDs may be intentionally set by software producers. Since this recorder plays DVD VIDEOs/VIDEO CDs according to the disc contents the software produ cers designed, some playback features may not be available. Also, see the instructions supplied with the DVD VIDEOs/ VIDEO CDs.

Note on DualDiscs

A DualDisc is a two sided disc product which mates DVD recorded material on one side with digital audio material on the ot her side. However, since the audio material side does not conform to the Compact Disc (CD) standard, playback on this product is not guarant eed.

Region code (DVD VIDEO only)

Your recorder has a region code printed on th e rear of the unit and will only play DVD VIDEOs (playback only) labeled with identical region codes. This system is used to prote ct copyrights. DVD VIDEOs labeled will also play on this recorder. If you try to play any other DVD VIDEO, a message will appear on the TV screen to indicate that the disc is not playable. Depending on the DVD VIDEO, no region code indication may be labeled even though playing the DVD VIDEO is prohibited by area restrictions.

Music discs encoded with copyrigh t protection technologies

This product is designed to playback discs that conform to the Compact Disc (CD) standard. Recently, various music discs encoded with copyright protection technol ogies are being marketed by some record compani es. Please be aware that among those disc s, there are some that do not conform to the CD standard and may not be playable by this product.

Note on DVD+RWs/DVD+Rs, DVD-RWs/DVDRs, or CD-RWs/CD-Rs recorded on other equipment

Some DVD+RWs/DVD+Rs, DVD-RWs/DVDRs, or CD-RWs/CD-Rs cannot be played on this recorder due to the recording quality or physical condition of the disc, or the characteristics of the recording device and authoring software. The disc will not play if it has not been correctly finalized. For more information, see the operating instructions for the recording device.

Notes

•You can not mix VR mode and Video mode on the same DVD-RW or DVD-R. To change the DVD-RW’s format, reformat the disc (page 64). Note that a disc’s contents will be erased after reformatting.

•You cann ot shorten the time required for recording even with high-speed discs. Also, you cannot record on the disc if the disc is not 1x speed compatible.

•It is recommended that you us e discs with “For Video” printed on their packaging.

•You cannot add new recordings to DVD-RWs (Video mode), DVD+Rs, or DVD-Rs (Video mode) recorded on other equipment.

•You m ay not be able to further record on a DVD+RW recorded on other equipment. Note that recording on such discs may cause the recorder to rewrite the DVD menu.

•If the dis c contains PC data unrecognizable by this recorder, the data may be erased.

ALL

Region code

Playback

Playing Discs

Press Z OPEN/CLOSE, and place a disc on the disc tray.

2 Press Z OPEN/CLOSE to close the disc

tray.

Wait until “LOAD” disappears from the front panel display.

3 Press H PLAY.

Playback starts.

To stop playback

Press x STOP.

z Hints

•You can play DATA CDs or DATA DVDs with MP3 audio tracks or JPEG image files (pages 41 or 42).

• If you insert a DVD VIDEO, VIDEO CD, or CD, playback starts automatically depending on the disc.

•When playing a DVD+RW, DVD-RW, DVD+R, DVD-R, and DVD-RAM, you can select the title from the Title List menu (page 38).

•When using a DVD-RAM with a cartridge, remove the disc from the cartridge.

Note

To play a disc recorded with other equipment on this recorder, finalize the disc on the recording equipment first.

Using the DVD’s Menu

When you play a DVD VIDEO, or a finalized DVD+RW, DVD-RW (Video mode), DVD+R, or DVD-R (Video mode), you can display the disc’s menu by pressing TOP MENU or MENU.

DVD

VCD

Video

DATA DVD

DATA CD

Video

RAM

11 22 33

44 55 66

77 880099

x STOP

Z OPEN/

H PLAY

TOP MENU

Playback side facing down

DVD

Video

Playback

Playback Options

Button Operation Disc

Z OPEN/CLOSE Stops playi ng and opens the disc tray. All discs

AUDIO Selects one of the audio tracks recorded on the disc

when pressed repeatedly.

: Selects the main or sub sound.

: Selects the audio source.

: Selects stereo or monaural audio tracks.

SUBTITLE Selects a subtitle language when pressed repeatedly.

ANGLE Selects an angle when pressed repeatedly.

If various angles (multi-angles ) for a scene are recorded on the disc, “ ” appears on the TV sc reen for a few seconds. See the instruct ions supplied with the disc for details.

REPLAY/ ADVANCE

•Replays or briefly fast forwards a scene when pressed during playback.

•Goes to the previous or next frame when pressed during pause mode.

. PREV/ > NEXT

•Goes to the beginning of the current or next title/ chapter/scene/track and starts playback when pressed during playback.

•Goes to the beginning of the previous title/chap ter/ scene/track when .PREV is pressed within three seconds after starting a title/chapter/scene/track.

All discs

11 22 33

44 55 66

77 880099

Z OPEN/CLOSE

X PAUSE

AUDIO

. PREV

REPLAY/ ADVANCE

x STOP

SUBTITLE

H PLAY

M/m/</,, ENTER

Number buttons

O RETURN

> NEXT

ANGLE

RWVR-RVR

DVD

VCD

DVD

VCD

RWVR-RVR

DVD

RWVR-RWVideo

DVD

RVR

RVideo

RAM

,continued

To resume normal playback after pl aying at various speeds, press H PLAY.

z Hints

•You can change playback options, such as subtitle, audio track, angle, etc., using the OPTIONS menu (page 11).

•During playback or pause mode, you can also use the

./> buttons on the recorder as the remote’s m/ M buttons. Hold the buttons down during playback to

fast reverse or fast forward. In pause mode, you can play in slow motion. Three speeds are available, depending on the duration of the press.

•See “DVD Audio/Subtitle Language” on page 100 for the meaning of the language abbre viation.

Notes

• If y ou pause playback of a CD, or DATA CD/DATA DVD containing MP3 audio tracks, playback will not start until you press H PLAY or X PAUSE.

•Sound will be interrupted during Scan Audio (page 37).

Notes on playing DTS soundtracks on a CD

When playing DTS-encoded CDs, excessive noise will be heard from the analog stereo jacks. To avoid possible damage to the audio system, the consumer should take proper precautio ns when the analog stereo jacks of the recorder are connected to an amplification system. To enjoy DTS Digital Surround™ playback, an external

5.1-channel decoder system must be connected to the digital jack of the recorder.

Notes on playing DVDs with a DTS soundtrack

DTS audio signals are output only throug h the DIGITAL AUDIO OUT (COAXIAL)/HDMI OUT jack. When you play a DVD with DTS soundtracks, set “Digital Out” – “DTS” to “On” of “Audio” in the “Setup” display (page 82). If you connect the recorder to audio equipme nt without a DTS decoder, do not set “DTS” to “On” in “Audio” setup. A loud noise (or no sound) may come out from the speakers, which might disturb your ears or cause damage to the speakers.

(fast reverse/fast forward)

Fast reverses or fast forwards the disc whe n pressed during playback. Search speed changes with each press:

fast reverse fast forward

FR1 T t FF1

FR2*2 T T t t FF2

FR3*3 T T T t t t FF3

All discs

FF1 with sound (Scan Audio) is available for DVDs with Dolby Digital soundtracks.

FR2 and FF2 are not available for MP3.

FR3 and FF3 are only available for DVDs and VIDEO CDs.

(slow)

Plays in slow motion when pressed in pause mode. Playback speed changes with each press:

reverse slow motion forward slow motion

T t

T T t t

T T T t t t

*Playback direction

only

X PAUSE Pauses playback.

If you pause playback for more than five minutes, playback starts automatically.

All discs

Button Operation Disc

VCD

Video

DVD

Video

RAM

1-8

Playback

Playing quickly with sound (Scan Audio)

(DVDs with Dolby Digital soundtracks

only)

You can play quickly with dialog or sound during FF1 fast-forward of a DVD with Dolby Digital soundtracks. Simply press M during playback.

z Hint

To turn off the Scan Audio function, set “Scan Audio” of “Audio” to “Off” in the “Setup” displ ay (page 83).

Note

Sound will be interrupted during Scan Audio.

Playing VIDEO CDs with PBC functions

PBC (Playback Control) allows you t o play VIDEO CDs interactively using a menu on your TV screen. When you start playing a VIDEO CD with PBC functions, a menu appears. Select an item using the number bu ttons and press ENTER. Then follow the instructions in the menu (press H PLAY when “Press SELECT” appears). Operations differ depending on the disc. See the instructions supplied with the disc.

To cancel PBC Playback

Press MENU to display “Menu: O ff.” To use the PBC functions, press MENU agai n to display “Menu:On.”

Resuming playback from the point where you stopped the disc (Resume Play)

Press H PLAY again after stopping a di sc to resume playback from the same point. To start from the beginning, press x STOP twice, and press H PLAY.

The point where you stopped playi ng is cleared when: –you open the disc tray. –you play another title. –you switch the Title List menu to original or

Playlist (DVD-RW (VR mode)/DVD-R (VR mode)/DVD-RAM only).

– you edit the title after stopping playback. – you make a recording.

Playing restricted DVDs (Parental Control)

If you play a restricted DVD, a message appears asking whether you want to override the restriction.

Select “OK” and press ENTER. The display for entering your password appears.

Enter your four digit password using the number buttons. The recorder starts playback.

To register or change the password, see “Parental (DVD VIDEOs only)” on page 86.

Locking the recorder (Child Lock)

You can lock all of the buttons on the recorder so that the settings are not canceled by mistake.

With the recorder turned on and stopped, hold down x (stop) on the recorder

for more than ten seconds. The recorder turns off and “CHILD LOCK” appears in the front panel display. The indicator remains lit if there is a timer setting. The recorder will not work except for timer recordings.

To unlock the recorder, hold down x on the recorder until “CHILD LOCK” disappears from the front panel display. The recorder is unlo cked and turns on.

To stop timer recording while the recorder is locked, press x twice. The recording stops and the recorder is unlocked.

Note

The recorder will be unlocked w hen you stop timer recording by pressing x.

VCD

DVD

REC

,continued

One-Touch Play (for HDMI connections only)

Press H PLAY. With one touch of the H PLAY button, your TV automatical ly turns on

and the TV’s input is switched to the recorder. Playback starts automatically. Set “Control for HDMI” to “On” in the “Features” setup (page 85) to use this function. The TV’s input will also switch to the recorder automatically if a disc with auto play function is loaded.

Notes

•Whe n using the HDMI connection, there may be a delay, before the playback picture appears on the TV screen, and the beginning portion of the playback picture may not be displayed.

•The function does not work when playing an audio CD, MP3 audio track.

•The f unction works only when the recorder is turned on.

Playing a Title From the Title List

The Title List menu displays the program titles on the disc.

1 Place a disc on the disc tray. 2 Press TITLE LIST.

Example: DVD-RW (VR mode)

A Disc type:

Displays a disc type. Also displays the title type (original or Playlist) for DVD-RWs (VR mode), DVD-Rs (VR mode), and DVD-RAMs.

B Movie thumbnail image C Title information:

Displays the title number, title name, recording date, and recording mode . “” indicates a protected title, while “” indicates un protected.

D Clock

Video

RAM

Video

11 22 33

44 55 66

77 880099

TITLE LIST

TOP MENU

ORIGINAL/ PLAYLIST

M/m/</,, ENTER

10:10 AM

01 LINE 1 >01:29:03

02 LINE 1 >00:31:23

03 LINE 1 >01:59:00

04 LINE 1 >00:58:56

LINE

08:00 PM

May/02/2008

No. Title Length Edit

Title List (Original)

1/4

Playback

Select the title, and press ENTER.

The sub-menu appears.

Select “Play,” and press ENTER.

Playback starts from the selected title on the disc.

About the Title List for DVD-RWs (VR mode) and DVD-Rs (VR mode)

You can switch the Title List to show an orig inal or Playlist. While the Title List menu is turned on, press ORIGINAL/PLAYLIST repeatedly to select either “Title List (Original)” or “Playlist.” For details, see “Edit options for DVD-RWs (VR mode)/DVD-Rs (VR mode)” on page 57.

To turn off the Title List

Press TITLE LIST.

z Hint

You can also switch the Title List of DVD-RAMs to show an original or Playlist.

Notes

•The Title List does not appear for DVD-RWs (Video mode), DVD+Rs, or DVD-Rs (Video mode) that have been finalized. To view a title, press TOP MENU or MENU (page 34).

•The Title List may not appear for discs created on other DVD recorders.

•Letters that cannot be displayed are replaced with “*.”

Searching for a Title/ Chapter/Track, etc.

You can search a DVD by title or chapter, and VIDEO CD by track or scene. As titles and tracks are assigned individual numbers on the disc, select the title or track by entering its number. You can also search for a scene using the time code.

Press OPTIONS during playback.

The OPTIONS menu appears.

Select a search method.

“Title” (for DVDs) “Chapter” (for DVDs) “Track” (for VIDEO CDs with PBC function off) “Time” (for DVDs/VIDEO CDs with PBC function off): Searches for a starting point using the time code.

Press M/m/</, to select the number of the title, chapter, track, etc., you want, or press the number buttons to enter the time code.

For example: “Time” To find a scene at 2 hours, 5 minutes, and 20 seconds, enter “20520.” If you make a mistake, wait a moment until the display returns to the elapsed playing time display, then select another number.

VCD

Video

RAMDVD

Video

11 22 33

44 55 66

77 880099

OPTIONS

M/m/</,, ENTER

Number

buttons

,continued

4 Press ENTER.

The recorder starts playback from the selected point. To turn off the display, press OPTIO NS.

Notes

•Depending o n the disc, you may not be able to use the OPTIONS menu to search for a title/chapter/track, or enter the time code for a playback point.

•When playing a Playlist title , you may not be able to search for a scene using the time code.

Displaying the Playi ng Time and Play Information

You can check disc information, suc h as playing time, recording mode, and remaining disc space.

Press DISPLAY.

The information display appears. Each time you press the button, the display changes as follows:

Disc information/date and time

Disc information only

No display

A Playing status B Playing time C Recording mode D Remaining disc space (in stop mode)

Remaining time of the current title (during playback

)

E Input source

F Date and time

DVD

VCD

RWVR-RWVideo

DATA CD

DATA DVD

RAM

RVR

RVideo

11 22 33

44 55 66

77 880099

TIME/TEXT

DISPLAY

Fri May 02. 2008 10:10 AM

Play

0:05:30

Rem 00:25

Original

1-9

Playback

Also appears in stop mode with Resume Play activated (page 37).

Title type (original or Playlist) for DVD-RWs (VR mode)/DVD-Rs (VR mode)/DVD-RAMs.

Viewing information on the front panel display

You can view the information on the front panel display.

Press TIME/TEXT repeatedly.

The displays differ depending on t he disc type or playing status.

Example: When playing a DVD

Example: When a DVD is stopped

Example: When playing a CD

Playing MP3 Audio Tracks and JPEG Image Files on the Disc

You can play DATA CDs (CD-ROMs/CD-Rs/ CD-RWs)/DATA DVDs (DVD-ROMs/ DVD+RWs/DVD-RWs/DVD+Rs/DVD-Rs) that contain MP3 audio tracks or JPEG image files.

Playing MP3 audio tracks

You can play MP3 audio tracks on DATA CDs or DATA DVDs.

1 Place a DATA CD/DATA DVD on the disc

tray.

When you insert a DATA CD/DATA DVD containing MP3 audio tracks and JPEG image files, the display for selecting a media type appears. When you select “Mix,” you can enjoy a slide show with sound (page 43).

VCDVD

SAP

SYNCHRO PROGRESSIVE

REC

STEREO

VCDVD

SAP

SYNCHRO PROGRESSIVE

REC

STEREO

VCDVD

SAP

SYNCHRO PROGRESSIVE

REC

STEREO

Playing time of the current title

Current title number and curren t chapter number

Clock

Current title and chapter number

Remaining disc space

Input source

Playing time of the current track

Current track number

Clock

DATA CD

DATA DVD

11 22 33

44 55 66

77 880099

H PLAY

O RETURN

M/m/</,, ENTER

. PREV/ > NEXT

TOP MENU

x STOP

OPTIONS

X PAUSE

10:10 AM

Photo

Music

Mix

Press ENTER :

Music menu for this disc.

,continued

If you insert a DATA CD/DATA DVD containing only MP3 audio tracks , the “Music” display appears. Go to step 4.

2 Select “Music,” and press ENTER.

The “Music” display appears.

3 Select an album, and press ENTER.

4 Select a track, and press ENTER.

Playback starts from the selected track. When a track or album is being played, the title is shown in a box.

To stop playback

Press x STOP.

To pause playback

Press X PAUSE. To restart playback, press H PLAY or X PAUSE.

To return to the previous display

Press O RETURN.

To switch between MP3 audio tra cks and JPEG image files

Press x STOP, and press TOP MENU.

z Hint

When playback of all the MP3 audio tracks within the album finishes, the recorder stops.

Playing JPEG image files

You can play JPEG image files on DATA CDs or DATA DVDs.

1 Place a DATA CD/DATA DVD on the disc

tray.

When you insert a DATA CD/DATA DVD containing MP3 audio tracks and JPEG image files, the display for selecting a media type appears.

When you select “Mix,” you can

enjoy a slide show with sound (page 43).

If you insert a DATA CD/DATA DVD containing only JPEG image files, the “Photo” display appears. Go to step 3.

2 Select “Photo,” and press ENTER.

The “Photo” display appears.

3 Select a folder, and press ENTER.

To display the previous or next page, press . PREV/> NEXT.

4 Select an image file, and press ENTER.

The selected image is displayed over the entire screen. To display the previous or next image, press . PREV/> NEXT.

The following menu icons appear in the upper part of the screen.

: Returns to the “Photo” display.

: Starts the slide show (page 43). : Rotates the image (page 43). : Zooms the image (pag e 43).

Stop 00:00:00

Prev Directory

01-Track1.mp3

02-Track2.mp3

03-Track3.mp3

04-Track4.mp3

05-Track5.mp3

MP3_001

0/9

10:10 AM

Music

Surround:Off

10:10 AM

Photo

Music

Press ENTER :

Mix

Music menu for this disc.

Slideshow

\abc\defg

Page 1 / 2

10:10 AM

Photo

Directory information

Playback

Press OPTIONS to turn on/off the menu icons.

To play the slide show

1 Press </, to select “ ,” and pr ess

ENTER. The “Slideshow Speed” menu app ears. “”: Slow “”: Normal “”: Fast

2 Press </, to select the desired play speed,

and press ENTER. The slide show starts from the select ed image. To stop playing, press x STOP.

To rotate the selected image

Press </, to select “ ,” and press ENTER. Each time you press ENTER, the image turns clockwise by 90°.

To zoom in an image

Press </, to sele ct “,” and press ENTER. Each time you press ENTER, the magnification changes as follows: 2u t 4u t 2u t normal

To return to the previous display

Press O RETURN.

To switch between MP3 audio tr acks and JPEG image files

Press x STOP, and press TOP MENU.

z Hint

You can also start the slide show by pressing H PLAY in step 4 above.

Notes

•You cannot use M/m/</, to move the image within

the screen while zooming.

•Slide show can play in only one dire ction.

•You cannot rotate or zoom during slide show.

•

If you select “ ” in the rotated image display, the images in the “Photo” display will not be rotated.

Enjoying a slide show with sound

When a disc contains both MP3 audio tracks and JPEG image files, you can enjoy a slide show with sound.

1 Insert a DATA CD/DATA DVD containing

both the MP3 audio tracks and JPEG image files.

The display for selecting a media type appears.

2 Select “Mix,” and press ENTER.

The “Music” display appears.

3 Select an album, and press ENTER. 4 Select a track, and press ENTER.

Playback starts from the selected tr ack, and the display asks for confirmation.

5 Select “Yes,” and press ENTER.

The “Photo” display appears.

6 Select the folder you want to view, and

press ENTER.

7 Press H PLAY to start the slide show.

The “Slideshow Speed” menu appears.

8 Press </, to select the slide show

speed, and press ENTER.

The slide show starts with sound.

To stop the slide show

Press x STOP.

z Hint

When playing JPEG images, you can also use the onscreen menu. For details, see “Playing JPEG image files” (page 42).

10:10 AM

Photo

Music

Press ENTER :

Mix

Music menu for this disc.

,continued

About MP3 audio tracks and JPEG image files

MP3 is audio compression technology that satisfies the ISO/IEC MPEG regulations. JPEG is image compression technology. You can play back DATA CDs (CD-ROMs/CDRs/CD-RWs) or DATA DVDs (DVD-ROMs/ DVD+RWs/DVD-RWs/DVD+Rs/DVD-Rs) recorded in MP3 (MPEG1 Au dio Layer 3) and JPEG format. However, this recorder only plays DATA CDs whose logical format is ISO9660 Level 1/Level 2 or Joliet, and DATA DVDs of Universal Disk Format (UDF). See the instructions supplied with the disc drives and the recording software (not supplied) for details on the recording format.

z Hint

The recorder can play MP3 audio tracks or JPEG image files stored in a USB device conn ected to the USB jack (page 45).

Note

The recorder may not be able to play some DATA CDs or DATA DVDs created in the Packet Write format.

MP3 audio tracks or JPEG im age files that the recorder can play

The recorder can play the following tracks and files:

–MP3 (MPEG1 Audio La yer 3) audio tracks. –MP3 audio tracks with the ex tension “.MP3.” –JPEG image files with the extension “.JPEG” or

“.JPG.”

z Hints

• If you add nu mbers (01, 02, 03, etc.) to the front of the file names, the files will be played in that order.

•Sinc e a disc with many trees takes longer to start playback, it is recommended that you create albums with no more than two trees.

Notes

•Some DATA CDs or DATA DVDs cannot be played on this recorder depending on file format.

•Only one se ssion of a multi-session DATA DVD can be played back.

•Only alpha bet and numbers can be used for album or track names. Anything else is displayed as an asterisk.

•The reco rder will play any data with the extension “.MP3,” even if they are not in MP3 format. Playing such data may generate a loud noise which could damage your speaker system.

•The reco rder does not conform to audio tracks in MP3PRO format.

•The r ecorder can recognize up to 499 MP 3 audio tracks within a single album. The recorder may not recognize some discs depending on the recording device used for recording or the disc condition.

•The recorder can play MP3 audio tracks recorded in the following sampling frequencies: 32 kHz, 44.1 kHz, 48 kHz.

•ID3 t ags cannot be displayed.

• If you add the extension “.JPG” or “.JPEG” to data not in JPEG format, a message appears indicating that the format is not supported.

•Depending on the disc or the size or tota l number of files, playback may take some time to start.

•The r ecorder can recognize up to 999 JPEG image file s within a single folder. The recorder may not recognize some discs depending on the recording device used for recording or the disc condition.

•Progressive and lo ssless compression JPEG image files are not supported.

•The im age size that the recorder can display is limited to width 32 - 7680 pixels by height 32 - 8192 pixels.

•JPEG image f iles that conform to the DCF* image fil e format are not supported.

*“Design rule for Camera File system”: Image standards

for digital cameras regulated by JEITA (Japan Electronics and Information Technology Industries Association).

1-10

Playback

Playing From a Connected USB Device

You can play MP3 audio tracks or JPEG ima ge files stored in a USB device connected to the USB jack. Also movie files in the connected HDD camcorder can be played. About USB connection and available USB devices, see pa ge 71.

Press INPUT repeatedly to select “USB.”

Connect a USB device to the (USB) jack (page 71).

Check that the USB indicator light s up in the front panel display.

Press H PLAY.

The display for selecting a media type appears.

Select “Photo,” “Music,” or “Movie ,” and press ENTER.

•To play MP3 audio tracks, select “Music.” See “Playing MP3 audio tracks” (pa ge 41) for details.

•To play JPEG image files, select “Photo.” See “Playing JPEG ima ge files” (page 42) for details.

•To play movie files, select “Movie.” The contents of the HDD camcorder are listed.

Example: When “Movie” is selected

Select an album (folder) and press ENTER.

The movie file list appears.

Select a movie file and press ENTER.

Playback starts.

To stop playback

Press x STOP.

To pause playback

Press X PAUSE. To restart playback, press H PLAY or X PAUSE.

To return to the previous display

Press O RETURN.

To return to the display for selecting a media type

Press x STOP twice, and press H PLAY.

11 22 33

44 55 66

77 880099

H PLAY

O RETURN

M/m/</,, ENTER

x STOP X PAUSE

INPUT

10:10 AM

Photo

Music

Movie

Press ENTER :

Music menu for this USB device.

USB

00:00:00Stop

AVF_INFO

MP_ROOT

DCIM

10:10 AM

USB

FileAlbum

USB

0/0

00:00:00Stop

Prev Directory

M2U00026.MPG

M2U00027.MPG

M2U00028.MPG

M2U00029.MPG

M2U00030.MPG

10:10 AM

USB

FileAlbum

USB

0/5

101PNV01

,continued

z Hints

•The recorder can play movie files that are recorded with an HDD camcorder and have the extension “.MPG.”

•You cannot play movie files recorded with a di gital still camera.

Notes

•The recorder may not be able to play some JPEG image files, MP3 audio tracks or movie files that have been edited on a PC.

•Do not disconnect a USB device while reading or playing files.

•Some files may take time to appear. In particular, it may take some time to read many files or large size files, but this is not a malfunction.

•Do not turn off the power while reading or playing files.

•USB cables exclusi ve for supplying power cannot be used.

•Conne ct the camcorder or digital still camera directly to the recorder, not via a USB hub or other USB device.

Recording

Before Recording

Before you start recording…

•This recorder can recor d on various disc types. Select the disc type according to your needs (page 30).

•Check that the disc has enough available space for the recording (page 40). For DVD+RWs or DVD-RWs, you can free up disc space by erasing titles (page 58).

•Check that the recorder is connected to a tuner such as a cable box or satellite receiver (page 12). See also the tuner’s instruction manual.

z Hints

•To play a disc recorded with this recorder on other equipment, finalize the disc (page 66). Note that you cannot further record or edit on a finalized disc.

• If you set “Auto Finalize” to “On” in the “Features” setup (page 85), the Auto Finalize function wo rks for DVD-RWs (Video mode), DVD-Rs (Video mode) and DVD+Rs after recording. For details, see page 67.

Notes

•Timer recordings will start with or without the recorder turned on. The recorder automatically turns off after a recording has finished.

•This recorder records at ×1 speed.

Maximum recordable number of titles

Recording mode

Like the SP or EP recording mode of VCRs, this recorder has eight differe nt recording modes. Select a recording mode according to the time and picture quality you need. For exam ple, if picture quality is your top priority, select “HQ” (high quality). If recording time is your priority, “SLP” can be a possible choice.

Press REC MODE repeatedly to switch the recording modes.

Recording mode and recording time

The following table is an approximate guide for the recording time on a single DVD (4.7 GB).

z Hint

The approximate recording time for DVD+R DL (Double Layer) discs is as follows: HQ: 1 hour 48 minutes HSP: 2 hours 42 minutes SP: 3 hours 37 minutes LSP: 4 hours 31 minutes ESP: 5 hours 25 minutes LP: 7 hours 14 minutes EP: 10 hours 51 minutes SLP: 14 hours 28 minutes

Notes

•Whe n in a recording mode other than HQ, the recorder compresses the audio/video data before record ing. Since the compression rate need s to decrease for fastmoving images or if picture noise is present, recorded data size increases, and available recording time becomes shorter. When recording such pictures, a recording mode offering longer recording time is recommended.

•Situations below may cause inaccuracies with the recording time. –Recording fast-moving or images containing picture

noise.

–Recordi ng a program with poor reception, or a

program or video source of low picture quality

Disc Number of titles

DVD-RW/DVD-R 99

DVD+RW/DVD+R 49

DVD+R DL 49

Recording mode Approximate

recording time (minute)

HQ (High quality) 60 HSP R 90

SP (Standard mode) 120 LSP r 150 ESP r 180 LP r 240 EP r 360

SLP (Long duration) 480

I want to record with the best possible picture quality, so I’ll select HQ.

,continued

–Recording on a disc that has already been edited –Recording only a still picture or just sound

•Since the recording mode for recorded titles is calculated after sampling the recorded data during playback, it may be displayed differently from the mode you selected when recording. Howeve r, the actual recording itself is correctly made in the selected mode.

Recording main and sub sounds

You can record the different soun dtracks on a DVD-RW (VR mode) or DVD-R (VR mode) from equipment connected to the LINE 1 IN or LINE 2 IN jacks. When playing the disc, you can select main or sub sound by pressing the AUDIO button. Set “Line Audio Inpu t” in “Audio” setup to “Main/Sub” in the Se tup Display (page 84). When recording on other discs, select eithe r sound track with the connected equipment before recording.

Unrecordable pictures

Pictures with copy protection ca nnot be recorded on this recorder. Recording stops when a copy guard signal is detected.

Not recordable on non-CPRM compatible DVDs that are commonly available.

The recorded disc can be played only on CPRM compatible equipment (page 30).

Formatting a new disc

New, unformatted discs are automatically formatted when first i nserted in the recorder. For DVD-RWs/DVD-Rs, you can select a recording format (VR mode o r Video mode) according to your needs (pa ge 30).

•Unused DVD-RWs are automatically formatted according to the setting of “Format DVD-RW” in “Features” setup (pag e 85).

•Unused DVD-Rs are automatically formatted in Video mode. To format in VR mode, change the recording format using the “Disc Setting” display (page 64).

Notes

•You cann ot mix VR mode and Video mode on the same DVD-RW or DVD-R.

•You can change the recording format on DVD-RWs by reformatting (page 64).

•You ca nnot change the recording format on used DVDRs.

•The recorder records on new DVD-Rs in Video mode unless you first format the discs in VR mode.

Copy control signals

Recordable discs

Copy-Free

Copy-Once

(CPRM*2) (CPRM

)

Copy-Never None

RWVR-RWVideo

RVR

RVideo

RWVR

RVR

1-11

Recording

Recording From Connected Equipment Without the Timer

You can record TV programs on the recorder through the connected cable box/satellite receiver.

Note

To play a disc recorded with this recorder on other equipment, finalize the disc (page 66). If you set “Auto Finalize” to “On” in the “Features” setup (page 85), the Auto Finalize function works for DVDRWs (Video mode), DVD-Rs (Video mode) and DVD+Rs after recording. For details, see page 67.

1 Turn on the recorder and the connected

cable box/satellite receiver.

2 Press Z OPEN/CLOSE, and place a

recordable disc on the disc tray.

3 Press Z OPEN/CLOSE to close the disc

tray.

Wait until “LOAD” disappears from the front panel display. Unused discs are automatically formatted. For the DVD-RW/DVD-R’s recording format (VR mode or Video mode), see “Formatting a new disc” on page48.

4 Press CH +/– or INPUT repeatedly to select

the channel or input source you want to record.

•When using the cable box/satell ite receiver control, select the channel by pressing CH +/– on this recorder’s remote. The recorder’s input is switched to the connected input (LINE1 or LINE2) . You can also use the number buttons.

•When not using the cable box/satellite receiver control, select the co nnected input (LINE1 or LINE2) by pressing INPUT, and then select the chann el on the cable box/ satellite receiver’s side.

5 Press REC MODE repeatedly to select the

recording mode.

The display changes on the TV screen as follows:

For details about the recording mode, see page 47.

6 Press z REC.

Recording starts. Recording continues until you stop the recording or the disc is full. Leave the cable box/satellite receiver turned on and do not change the channel you are recording.

To stop recording

Press x STOP. Note that it may take a few seconds for the recorder to stop recording.

To pause recording

Press X PAUSE. To restart recording, press X PAUSE again.

Video

11 22 33

44 55 66

77 880099

REC MODE

X PAUSE

x STOP

CH +/–

z REC

Z OPEN/

H PLAY

DISPLAY

INPUT

Recording side facing down

HQ SPHSP LSP

SLP LPEP ESP

,continued

z Hint

You can turn off the TV during recording.

Notes

•Recording may not start immedia tely after zREC is pressed.

•You cannot change the recording mode during recording or recording pause.

• If there is a power failure, the program you are recording may be erased.

•You cannot change the input source during recording.

Recording using the Quick Timer (One-touch Timer Recording)

You can set the recorder to reco rd in 30-minute increments.

Press z REC repeatedly to set the duration.

Each press increases the time by 30 minutes, up to eight hours*.

“c” and “OTR” light up, and the rem aining recording time appears in th e front panel display. When the time counter reaches “0:00,” the recorder stops recording a nd turns off.

*14 hours 30 minutes for DVD+R DL (Doubl e Layer)

discs.

To cancel the Quick Timer

Press zREC repeatedly until the counter appears in the front panel display. The recorder retur ns to normal recording mode .

To stop recording

Press x STOP twice. Note that it may take a few seconds for the recorder to stop rec ording.

Checking the disc status while recording

You can check the recording informat ion such as recording time or disc type.

Press DISPLAY during recording.

The information display appears. Press the button repeatedly to change the display (page 40).

A Disc type B Recording status C Recording time D Recording mode E Remaining disc space F Input source

z Hint

You can view the information also in the front panel display. Press TIME/TEXT repeatedly to change the display. Note that TIME/TEXT does not work during One-touch Timer Recording.

Creating chapters in a title

The recorder will automatically divide a recording (a title) into chapters by inserting chapter marks at 5 or 15-minute intervals during recording. Select the interval, “5 Min” (default) or “15 Min” in “DVD Auto Chapter” of “Features” in the “Setup” display (page 84). If you do not want to divide titles, select “O ff.”

0:30 1:00 7:30 8:00

(Normal recording)

Record

0:00:03

Rem 00:59

Line1

Recording

Timer Recording From Connected Equipment

You can set the timer for a total of 12 programs, up to one month in advance. Note that the maximum continuous recording time for a single title is 12 hours. Contents beyond this time will not be recorded. If you record from connected equipment that has a timer function, you can use the Synchro Rec function (page 54).

Notes

•Do not operate yo ur cable box or satellite receiver just before or during a timer recording. This may prevent the accurate recording of a program.

•To play a disc recorded with this recorder on other equipment, finalize the disc (page 66) . If you set “Auto Finalize” to “On” in the “Features” setup (page 85), the Auto Finalize function works for DVD-RWs (Video mode), DVD-Rs (Video mode) and DVD+Rs after recording. For details, see page 67.

1 Press Z OPEN/CLOSE, and place a

recordable disc on the disc tray.

2 Press Z OPEN/CLOSE to close the disc

tray.

3 Press TIMER.

4 Select an item using </, and adjust

using M/m.

A “Date”: Sets the date using M.

To record the same program e very day or the same day every week , press m. The item changes as follows: Today y Sun-Sat (Sunday to Saturday) y Mon-Sat (Monday to Saturday) y Mon-Fri (Monday to Friday) y Sun (every Sunday) y Mon (every Monday) y … y Sat (every Saturday) y 1month later y … y Today

B “Start”: Sets the start time. C “End”: Sets the stop time. D “Ch”: Selects the channel or input

source.

•When using the cable box/satel lite receiver control, sele ct the channel.

•When not using the cable box/sat ellite receiver control, select t he input, LINE1 or LINE2. Select the channel on the connected cable box/satellite receiver’s side before the timer recording starts.

E “Mode”: Selects the recording mode

(page 47).

To use the Rec Mode Adjust functi on (page 52), select “AUT O.”

If you make a mistake, select the item and change the setting.

RWVR-RWVideo

RVR-RVideo

11 22 33

44 55 66

77 880099

M/m/</,, ENTER

Z OPEN/

x STOP

SYSTEM

TIMER

Recording side facing down

01 DVD 04/15 09:00PM 10:00PM CH8

--- --/-- --:-- --:-- ---- ---04

--- --/-- --:-- --:-- ---- ---05

--- --/-- --:-- --:-- ---- ---06

03 --- --/-- --:-- --:-- ---- ---

02 DVD 04/30 09:15PM 09:45PM CH11

10:10 AM

No Rec To Date Start End Source Mode Edit

Timer – Standard

No.1

: PM PM

09 00 10 00 Line1 SP

12 3 45

Date Start End Ch Mode

Today

,continued

Press ENTER.

The Timer List menu (page 53) appea rs. The c indicator lights up in the front panel display, and the recorder is ready to start recording.

•If the c indicator flashes in the front panel

display, check that a recordable disc is inserted and that there is enough disc space for the recording.

•If timer settings overlap, a message appears. To change or cancel a timer recording, select “Edit” from the Timer List (page 53).

Press SYSTEM MENU to turn off the menu.

There is no need to turn off the recorder before the timer recording starts. Leave the cable box/satellite recei ver turned on and do not change the channe l selected on the cable box/satellite receiver until the recorder finishes the time r recording.

To stop recording

Press x STOP twice. Note that it may take a few seconds for the recorder to stop rec ording.

If timer settings overlap

The program that starts first has priority and the second program starts recording only after the first program has finished. If the programs start at the same time, the program listed first in the menu has priority. If the end time of one setting and the start time of another timer setting is the same, the beginning of the program that star ts later will be cut.

To change or cancel timer re cording

See “Changing or Canceling Timer Settings (Timer List)” on page 53.

To use the Rec Mode Adjust function

If the remaining disc space is not enough for the current recording, the recorder automatically adjusts the recording mode. Select “AUTO” for “Mode” when setting the timer.

z Hints

•You can play th e recorded program by selecting the program title in the Title List menu.

•You can also tu rn on the timer programming menu from the System Menu. Press SYSTEM MENU to select “Timer,” and select “Timer-Standard.”

Notes

•Even wh en correctly set, the program may not be recorded if another recording is underway, or ot her prioritized timer setting overlaps.

•Before the timer recording starts, “TIMER REC” flashes in the front panel display.

•The recorder automatically turns off when a timer recording finishes, even if the recording started with the recorder turned on.

•The recorder does not record programs with CopyNever signals. Such recordings stop after a few seconds.

7:00 8:00 9:00 10:00

Program 1

Program 2

will be cut off

Program 1

Program 2

will be cut off

1-12

Recording

Changing or Canceling Timer Settings (Timer List)

You can change or cancel timer settings using the Timer List menu.

Press SYSTEM MENU.

The System Menu appears.

Select “Timer,” and press ENTER.

Select “Timer List,” and press ENTER.

Timer information displays the recording date, time, recording mode, etc. If there are more than six timer settings, press m to display the next page.

Select the timer setting you want to change or cancel, and press ENTER.

The sub-menu appears.

Select one of the options, and press ENTER.

“Edit”: Changes the timer setting. Select an item using </, and adjust using M/m. Press ENTER.

“Erase”: Erases the timer setting. Select “OK” and press ENTER when asked for confirmation.

Press SYSTEM MENU to turn off the Timer List.

To return to the previous display

Press O RETURN.

Notes

•Even whe n correctly set, the program may not be recorded if another recording is underway, or other prioritized timer setting overlaps. For priority, see page 52.

Video

11 22 33

44 55 66

77 880099

SYSTEM

M/m/</,, ENTER

O RETURN

01 04/15 09:00PM 10:00PM Line1

--/-- --:-- --:-- ---- ---04

--/-- --:-- --:-- ---- ---05

--/-- --:-- --:-- ---- ---06

03 --/-- --:-- --:-- ---- ---

02 04/30 09:15PM 09:45PM Line1

10:10 AM

Timer List

No Date Start End Ch Mode Edit

01 04/15 09:00PM 10:00PM Line1

--/-- --:-- --:-- ---- ---04

--/-- --:-- --:-- ---- ---05

--/-- --:-- --:-- ---- ---06

03 --/-- --:-- --:-- ---- ---

02 04/30 09:15PM 09:45PM Line1

10:10 AM

Timer List

No Date Start End Ch Mode Edit

Edit

Erase

01 DVD 04/15 09:00PM 10:00PM CH8

--- --/-- --:-- --:-- ---- ---04

--- --/-- --:-- --:-- ---- ---05

--- --/-- --:-- --:-- ---- ---06

03 --- --/-- --:-- --:-- ---- ---

02 DVD 04/30 09:15PM 09:45PM CH11

10:10 AM

No Rec To Date Start End Source Mode Edit

Timer – Standard

No.1

PM PM

09 00 10 00 Line1 SP

Date Start End Ch Mode

04/15

01 04/15 09:00PM 10:00PM CH8

--/-- --:-- --:-- ---- ---04

--/-- --:-- --:-- ---- ---05

--/-- --:-- --:-- ---- ---06

03 --/-- --:-- --:-- ---- ---

02 04/30 09:15PM 09:45PM CH11

10:10 AM

No Date Start End Source Mode Edit

Timer List

Do you want to erase ‘No.01’?

Cancel

,continued

•You cannot change the timer settings for a recording currently underway.

Recording From Connected Equipment With a Timer (Synchro Rec)

You can set the recorder to automatically record programs from connected equipment that has a timer function (such as a satellite tuner). Connect the equipment to the LINE 1 IN (VIDEO/AUDIO) jacks on the rear of the recorder (page 13). When the connected equipment turns on, the recorder starts recording a program from the LINE 1 IN jacks.

Note

To play a disc recorded with this recorder on other equipment, finalize the disc (page 66).

1 Insert a recordable disc. 2 Select the line input audio.

Set “Line Audio Input” of “Audio” setup to “Stereo” or “Main/Sub” in the “Setup” display (page 84).

Video

11 22 33

44 55 66

77 880099

M/m/</,, ENTER

SYNCHRO REC

x STOP

REC MODE

SYSTEM

Recording

Press REC MODE repeatedly to select the recording mode.

The display changes on the TV screen as follows:

For details about the recording mode, see page 47.

Set the timer on the connected equipment to the time you want to record, and turn it off.

Press SYNCHRO REC.

The SYNC-REC indicator lights up in the front panel display and the recorder stand s by for Synchro-Rec. The recorder starts recordin g when a signal is received from the connected equipment. When the connected equipment turns off, the recording stops and the recorder turns off.

To stop recording

Press x STOP twice.

To cancel a Synchro-Rec funct ion

Press SYNCHRO REC before recording starts. The SYNC-REC indicator turns off in the front panel display. If you press SYNCHRO REC during SynchroRec, the recording stops, the SYNC- REC indicator turns off, and the recorder turns off.

If the timer settings of a Synchro-Recording and another timer recording overlap

Regardless of whether or not the program is a Synchro-Rec program, the program that starts first has priority. The recorder starts recording the second program about ten seconds after the first program has finished. If the end time of one setting and the start time of another timer setting is the same, the beginning of the program that starts later will be cut.

Notes

•The recorder starts recording only after detecting the video signal from the connected equipment. The beginning of the program may not be recorded regardless of whether or not the recorder’s power is on or off.

•To use the connected equipment during Synchro-Rec standby, cancel the standby mode by pressing SYNCHRO REC. To return to standby mode again, be sure to turn off the equipment and press SYNCHRO REC, before Synchro-Rec starts.

•The Synchr o-Rec function does not work with some tuners. For details, see the tune r’s operating instructions.

•The Synchr o-Rec function does not work for a video signal input via the LINE 1 IN S VIDEO jack.

•Aft er a recording has finished, the recorder enters the Synchro-Rec standby mode until the SYNC-REC indicator turns off in the front pa nel display.

•If Synchro-Rec starts with the recorder turned on, the recorder will turn off when the recording ends.

•The recorder does not record programs with CopyNever signals. Such recordings stop after a few seconds.

HQ SPHSP LSP

SLP LPEP ESP

7:00 8:00 9:00 10:00

Program 1

Program 2

will be cut off

Recording From a VCR or Similar Device

You can record from a connected VCR or similar device. For connection details, see “Connecting a VCR or Similar Device” on page 27. To record from the equipment that has a DV/D8 output jack (i.LINK jack), use t he DV IN jack on the front panel. For details, see page68. To record from a USB device connected to the USB jack, see page 71.

Note

To play a disc recorded with this recorder on other equipment, finalize the disc (page 66). If you set “Auto Finalize” to “On” in the “Features ” setup (page 85), the Auto Finalize function works for DVDRWs (Video mode), DVD-Rs (Video mode) and DVD+Rs after recording. For details, see page 67.

1 Insert a recordable disc.

2 Press INPUT repeatedly to select an input

source according to the connection you made.

The front panel display changes as follows:

When connecting to the LINE 2 IN jacks on the front panel, select “LINE2. ”

3 Press REC MODE repeatedly to select the

recording mode.

The display changes on the TV screen as follows:

For details about the recording mode, see page 47.

4 Select the line input audio.

Set “Line Audio Input” of “Audio” setup to “Stereo” or “Main/Sub” in the “Setup” display (page 84).

5 Insert the source tape into the connected

equipment and set to playback pause.

6 Press z REC on this recorder and the

pause or play button on the connected equipment at the same time.

Recording starts. To stop recording, press x STOP on this recorder.

Notes

•A video game image may not be recor ded clearly.

•The recorder does not record programs with CopyNever signals. Such recordings stop after a few seconds.

•During r ecording or recording pause, you cannot change the recording mode.

•You canno t change the input source during recording.

RWVR-RWVideo

RVR-RVideo

11 22 33

44 55 66

77 880099

INPUT

x STOP REC MODE

z REC

LINE2 DV USBLINE1

HQ SPHSP LSP

SLP LPEP ESP

1-13

Editing

Before Editing

This recorder offers various edit options for various disc types. Befo re you edit, check the disc type in the “Disc Informa tion” display (page 64), and select the option available for your disc.

Notes

•You may lose the edited contents if you r emove the disc or a timer recording starts while editing.

•You cannot edit recordings on DVD-RWs (Video mode), DVD+Rs, or DVD-Rs (Video mode) recorded on other DVD equipment.

Edit options for DVD+RWs/DVD-RWs (Video mode)/DVD+Rs/DVD-Rs (Video mode)

You can perform simple edits. Since Vi deo mode titles are actual recordings on the disc, you cannot undo any edits you make. The edit functions available for Video mode titles are: –Renaming a title (page 61). –Erasing a title (page 58). –Setting protection against erasure (DVD+RWs

only) (page 58).

–Erasing a section of a title (A-B Erase)

(DVD+RWs only) (page 59).

–Dividing a title (DVD+RWs only) (page 60).

Notes

•Once the disc is finalized, you cannot edit or r ecord on the disc (except for DVD+RWs).

• If a message appears and indicates that the disc’s control information is ful l, erase unnecessary titles.

Edit options for DVD-RWs (VR mode)/ DVD-Rs (VR mode)

You can enjoy advanced edit functions. First you have two options for a DVD-RW (VR mode) and DVD-R (VR mode): editing either the original recording (called the “original” ), or the playback information created from the original (called a “Playlist”). Since each is different in nature and offers different merits, read the following and select the one that better suits your needs.

To edit original titles

Edits made to the original titles are final. If you plan to retain an unaltered original recording, create a Playlist (see below). The edit functions available for original titles are: –Renaming a title (page 61). –Erasing a title (page 58). –Erasing a chapter (page 59). –Setting protection against erasure (page 58). –Erasing a section of a title (A-B Erase) (page59). –Dividing a title (page 60).

To create Playlist titles

A Playlist is a group of Playlist titles created from the original title. When you create a Playlist, only the control information necessary for playback, such as the playback order, is stored on the disc. The original titles are left unaltered. If you erase an original title used in a Playlist, that Playlist is also erased.

Example: You have recorded the final few matches of a soccer tournament on a DVD-RW (VR mode). You want to create a digest with the goal scenes and other highlights, but you also want to keep the original recording.

In this case, you can compile highlight scenes as a Playlist title.

Video

,continued

z Hints

•You can switch the Title List to show original or Playlist. While the Title List menu is turned on, press ORIGINAL/PLAYLIST repeatedly.

•You can rename or erase a Playlist title (page 64).

Notes

•You cannot protect Playlist titles.

• If a messa ge appears and indicates that the disc’s control information is full, erase un necessary titles.

•You cannot create or edit Playlist titles on a finalized disc. When you want to edit or record on the DVD-RW again, unfinalize the disc (page 66).

Editing a Title

This section explains the basic edit functions. Note that editing is irreversible. To edit a DVD-RW (VR mode) or DVD-R (VR mode) without changing the original recordings, create a Playlist title (page 62).

1 Press TITLE LIST.

When editing a DVD-RW (VR mode) or DVD-R (VR mode), press ORIGINAL/ PLAYLIST to switch to the “Title List (Original),” if necessary.

2 Select a title, and press ENTER.

The sub-menu appears.

Video

11 22 33

44 55 66

77 880099

M/m/</,, ENTER

TITLE LIST

H PLAY

X PAUSE

ORIGINAL/ PLAYLIST

. PREV/

> NEXT

O RETURN

Title List (Original)

10:10 AM

LINE

08:00 PM

May/02/2008

No. Title Length Edit

01 LINE 1 01:29:03

02 LINE 1 00:31:23

03 LINE 1 >01:59:00

04 LINE 1 >00:58:56

1/4

Editing

3 Select an option, and press ENTER.

You can select from the following: “Title Erase”: Erases the selected title. Select “OK” when asked for confirmation. “Chapter Erase”

: Allows you to select a chapter in the title and erase it (see below). “Protect”

: Protects the title. Select “On” when the Protection display appears. “ ” appears for the protected title. To ca ncel the protection, select “Off.” “ ” changes to “.” “Title Name”: Allows you to rename the title (page 61). “A-B Erase”

: Erases a section of the title (see below). “Divide Title”

: Divides a title into two

(page 60).

DVD-RWs (VR mode) and DVD-Rs (VR mode) only

DVD+RWs, DVD-RWs (VR mode), and DVD-R (VR mode) only

About freeing up disc space

Erasing titles, chapters, or scenes: –frees up disc space on a DVD-RW (VR mode). –frees up disc space on a DVD+RW/DVD-RW

(Video mode) only when you erase the last title or chapter.

–cannot free up disc space on a DVD+R/DVD+R

DL/DVD-R.

z Hint

You can also rename a disc (page 64).

Notes

•Whe n editing a DVD-RW (Video mode), DVD+R, or DVD-R, finish all editing before finalizing the disc. You cannot edit a finalized disc.

•You cannot erase protected titl es or erase chapters from a protected title.

• If you erase an original title used in a Playlist, that Playlist is also erased.

Erasing a chapter (Chapter Erase)

You can select a chapter within a title and erase it. Note that erasing chapters from original titles cannot be undone.

1 Press TITLE LIST.

Press ORIGINAL/PLAYLIST to switch to the “Title List (Original),” if necessary.

2 Select a title, and press ENTER.

The sub-menu appears.

3 Select “Chapter Erase,” and press ENTER.

The display for erasing chapters appears.

4 Select the chapter you want to erase, and

press ENTER.

“Check” is selected. To preview the chapter, press ENTER. When playback finishes or when you press O RETURN, the display returns to “Chapter Erase (Original).”

5 Select “Erase,” and press ENTER.

The display asks for co nfirmation.

6 Select “OK,” and press ENTER.

The selected chapter is erased from the title. To erase other chapters, repeat fr om step 4.

Note

If you erase an original title used in a Playlist, that Playlist is also erased.

Erasing a section of a title (A-B Erase)

You can select a section (scene) within a title and erase it. Note that erasing scenes from ori ginal titles cannot be undone.

1 Press TITLE LIST.

When editing a DVD-RW (VR mode) or DVD-R (VR mode), press ORIGINAL/ PLAYLIST to switch to the “Title List (Original),” if necessary.

RWVR-RVR

Chapter Erase (Original)

10:10 AM

Chapter No. 1 / 3 Title No.01

03 00:04:2002 00:00:1001 00:00:34

Check

Erase

RWVR-RVR

,continued

Select a title, and press ENTER.

The sub-menu appears.

Select “A-B Erase,” and press ENTER.

The display for setting point A and B appears. “Start” is selected.

Press ENTER at the start point of the section to be erased (point A).

You can use H PLAY, , . PREV/> NEXT, and X PAUSE to

find the point. At the point you want to select, press H PLAY or X PAUSE, and press ENTER. “End” is selected.

Press ENTER at the end point of the section (point B).

“Erase” is selected. To reset the start or end point, select “Start” or “End” and repeat from step 4 or 5.

Press ENTER.

The display asks for confirma tion.

Select “OK,” and press ENTER.

The scene is erased. To continue, repeat from step 4. To finish, select “Finish,” and press ENTER.

z Hint

A chapter mark is inserted after the scene was erased. The chapter mark divides the title into separate chapters on either side of the mark.

Notes

•Images or sound m ay be momentarily interrupted at the point where you erase a section of a title.

•Sections short er than five seconds may not be erased.

•The start and end points of a title may be different from what you have set.

•If you eras e an original title used in a Playlist, that Playlist is also erased.

Dividing a title into two (Divide Title)

You can divide a title into two. Note that dividing original titles cannot be undone.

Press TITLE LIST.

When editing a DVD-RW (VR mode) or DVD-R (VR mode), press ORIGINAL/ PLAYLIST to switch to the “Title List (Original),” if necessary.

Select a title, and press ENTER.

The sub-menu appears.

Select “Divide Title,” and press ENT ER.

The display for setting the dividing point appears. “Point” is selected.

A-B Erase

10:10 AM

Title No.01

End 00:00:00

Start 00:00:00

Start

End

Erase

Finish

00:00:07

Title No.01

May/02/2008 08:00 PM

A-B Erase

10:10 AM

Title No.01

End 00:00:00

Start 00:00:10

Start

End

Erase

Finish

00:00:10

Title No.01

May/02/2008 08:00 PM

Divide Title (Original)

10:10 AM

Title No.01

Point

Divide

00:00:07

Title No. 01

Start 00:00:00

End 00:00:00

May/02/2008 08:00 PM

1-14

Editing

Press ENTER at the point wher e you want to divide the title.

You can use H PLAY, , . PREV/> NEXT, and X PAUSE to

find the point. At the point you want to selec t, press H PLAY or X PAUSE, and press ENTER. “Divide” is selected.

Press ENTER.

The display asks for confirmation. To reset the dividing point, select “No” and press ENTER, then repeat from step 4.

Select “Yes,” and press ENTER.

The display asks whether to rename the title. To use the same name as before, select “No” and press ENTER to finish.

Select “Yes,” and press ENTER.

The “Title Name” display appea rs.

Follow steps 4 to 6 of “Changing the Name of a Title” (page 61) to complete renaming.

The divided title appears in the Title List with the new name.

z Hint

If the dividing point is set too close to the beginning of the title, the title cannot be divided.

Changing the Name of a Title

You can enter a title name of up to 32 characters. Since the displayed number of charac ters is limited, their appearance in menus such as Title List may be different. When the display for entering characters appears, follow the steps below.

Press TITLE LIST.

When editing a DVD-RW (VR mode) or DVD-R (VR mode), press ORIGINAL/ PLAYLIST to switch to the “Title List (Original),” if necessary.

Select a title, and press ENTER.

The sub-menu appears.

Select “Title Name,” and press ENTER.

The “Title Name” display appears.

10:10 AM

Title No.01

00:00:10

Divide Title (Original)

Title No. 01

End 00:00:10

Start 00:00:00

Point

Divide

May/02/2008 08:00 PM

Video

11 22 33

44 55 66

77 880099

M/m/</,, ENTER

O RETURN

TITLE LIST

ORIGINAL/ PLAYLIST

Title Name

A B C D E

F G H I J

K L M N O

P Q R S T

U V W X Y

a b c d e

f g h i j

k l m n o

p q r s t

u v w x y

1 2 3 4 5

6 7 8 9 0

- _ + = .

@ # $

%^& ( )

Backspace Space Delete Clear Finish

10:10 AM

Input row

Character paletteSetting buttons

Cursor

,continued

4 Select the character you want to enter

using M/m/</,, and press ENTER.

The selected character appear s in the input row. You can only enter charact ers and symbols that are displayed.

•To change the cursor position, select the

input row using M, and press </,.

•To erase a character, se lect either of the following setting buttons and press ENTER. “Backspace”: Erases the character t o the left of the cursor. “Delete”: Erases the character at the cursor position. “Clear”: Erases all the characters in the input row.

•To insert a space, move the cursor to the desired position, select “Space,” and press ENTER.

•To insert a ch aracter, move the cursor to the desired position, select the character, and press ENTER.

5 Repeat step 5 to enter the remaining

characters.

To return to the Title List without renaming the title, press O RETURN.

6 Select “Finish,” and press ENTER.

z Hint

You can also rename a disc (page 64). Follow steps 4 to 6 above when the “Disc Name” display appears.

Creating a Playlist

Playlist titles allow you to edit without changing the original recordings (see “Edit options for DVD-RWs (VR mode)/DVD-Rs (VR mode)” on page 57). You can create a Playlist title by combining up to 99 sections (scenes) from original titles.

Notes

•If you eras e an original title used in a Playlist, that Playlist is also erased.

•You cannot crea te or edit Playlist titles on a finalized disc. When you want to edit or record on the DVD-RW again, unfinalize the disc ( page 66).

1 Press SYSTEM MENU while the reco rder is

in stop mode.

11 22 33

44 55 66

77 880099

M/m/</,, ENTER

SYSTEM

H PLAY

TITLE LIST

X PAUSE

ORIGINAL/ PLAYLIST

. PREV/

> NEXT

O RETURN

Press ENTER :

Title Menu for DVD Title List.

10:10 AM

Title List (Original)

Setup

Disc Setting

Edit

Title List

Timer

Dubbing

Editing

Select “Edit,” and press ENTER.

Select “Create Playlist,” and press ENTER.

The display for creating a Playlist appears. “Start” is selected.

Press ENTER at the start point.

You can use H PLAY, , . PREV/> NEXT, and X PAUSE to

find the point. At the point you want to selec t, press H PLAY or X PAUSE, and press ENTER. “End” is selected.

Press ENTER at the end point.

“Make” is selected. To reset the start or end point, select “Start” or “End” and repeat step 4 or 5.

Press ENTER.

The selected section is captured as a scene. To continue, repeat from step 4.

When you finish capturing sce nes, select “Finish” and press ENTER.

To return to the previous display

Press O RETURN.

To turn off the display

Press SYSTEM MENU.

Playing a Playlist title

Press TITLE LIST.

Press ORIGINAL/PLAYLIST to switch to the “Playlist” Title List.

Select a Playlist title, and press ENTER.

The sub-menu appears.

Select “Play,” and press ENTER.

z Hint

When a Playlist title is created, th e start and end points will become chapter marks, and each scene will become a chapter.

Notes

•The picture may pause when an edited scene is played.

•The sta rt and end points in a title may be different from what you have set.

10:10 AM

Create Playlist

Edit Playlist

Edit

Setup

Disc Setting

Edit

Title List

Timer

Dubbing

Create Playlist

10:10 AM

Scene No.01

End 00:00:00

Start 00:00:00

Start

End

Make

Finish

00:00:07

---/--/---- --:--

Playlist No. 01

10:10 AM

Scene No.01

Finish

00:00:10

Create Playlist

Playlist No. 01

End 00:00:00

Start 00:00:10

Start

End

Make

---/--/---- --:--

Playlist

10:10 AM

01 LINE 1 >00:05:04

02 LINE 1 >00:00:51

03:25 PM

May/02/2008

No. Title Length Edit

1/2

LINE

,continued

Renaming and erasing a Playlist title

1 Press TITLE LIST. 2 Press ORIGINAL/PLAYLIST to switch to the

“Playlist” Title List.

3 Select a Playlist title, and press ENTER.

The sub-menu appears.

4 Select an option, and press ENTER.

Select from the following options. “Title Erase”: Erases the title. Select “OK” when asked for confirmation. “Title Name”: Allows you to rename the title (page 61).

z Hint

You can also edit Playlist titles from the System Menu. Press SYSTEM MENU to select “Edit,” and select “Edit Playlist.”

Note

You cannot create or edit Playlist titles on a finalized disc. When you want to edit or record on the DVD-RW again, unfinalize the disc (page 66).

Formatting/Renaming/ Protecting a Disc

The “Disc Setting” display allows you to check the disc information or change the disc name. Depending on the disc type, you can a lso format or set protection.

1 Press SYSTEM MENU while the reco rder is

in stop mode.

2 Select “Disc Setting,” and press ENTER.

The “Disc Setting” display appears.

3 Select an option, and press ENTER.

A “Disc Name”: Allows you to rename a

disc. For details on how to enter characters, see page 61.

Playlist

10:10 AM

01 LINE 1 >00:05:04

02 LINE 1 >00:00:51

03:25 PM

May/02/2008

No. Title Length Edit1/2

LINE

RWVR-RWVideo

RVR

RVideo

11 22 33

44 55 66

77 880099

SYSTEM

M/m/</,, ENTER

O RETURN

Disc Setting

10:10 AM

Disc Name :

Disc Protect : Not Protected

Disc Format : VR Mode

Disc Finalize : Unfinalized

Disc Information

Erase All Titles

Setup

Disc Setting

Edit

Title List

Timer

Dubbing

2 3

4 5

1-15

Editing

B “Disc Protect” (DVD+RWs/DVD-RWs

(VR mode)/DVD-Rs (VR mode) only): Protects all titles on the disc when “Protected” is selected. To cancel the protection, select “Not Protected.”

C “Disc Format” (DVD+RWs/DVD-

RWs/DVD-Rs only): Erases all contents of the disc, including pro tected titles, and makes a blank disc (except DVD-Rs). For DVD-RWs, select a recording format (“VR Mode” or “Video Mode”) according to your needs. To format unused DVD-Rs in VR mode, select “VR Mode” and then “OK.”

D “Disc Finalize”: Finalizes a disc. See

page 66 for details.

E “Disc Information”: Displays the

following information.

•Disc name

•Disc type (and recording format for a DVD-RW (VR mode)/DVD-R (VR mode))

•Total number of titles

•Protect setting

•The oldest and most recent recording date

•The total available recording time in each recording mode

F “Erase All Titles” (DVD+RWs/DVD-

RWs/DVD-Rs (VR mode) only): Erases all titles on the disc (except protected titles). Select “OK” when asked for confirmation. For DVD-RWs (VR mode)/DVD-Rs (VR mode), Playlist titles created with protected titles are also erased.

To return to the previous display

Press O RETURN.

z Hints

•You can set protection for individual titles (page 5 8).

•By reformatting, you can change the recording format on DVD-RWs, or record again on DVD-RWs (Video mode) that have been finalized.

Notes

•You c an label a disc using up to 32 characters; however, the name may not display on other DVD equipment.

•You cannot label an unused DVD-R (Video mode) disc. Label the disc after you first record on it.

•You canno t mix VR mode and Video mode on the same DVD-RW or DVD-R.

•You ca nnot change the recording format on used DVDRs.

•The recorder records on new DVD-Rs in Video mode unless you first format the discs in VR mode (page 48).

10:10 AM

Disc Information

Disc Name

Media

Title No.

Protected

Date

Remainder

Disc 1

DVD-RW VR ModeFormat

Original 6 / Playlist 1

Not Protected

4/05/2008 ~ 4/30/2008

HQ : 0H 57M LSP : 2H 23M EP : 5H 46M

HSP : 1H 26M ESP : 2H 52M SLP : 7H 40M

SP : 1H 55M LP : 3H 50M

4.4/4.7GB

Finalizing a Disc (Preparing a Disc for Playback on Other Equipment)

Finalizing is necessary in order to play discs recorded with this record er on other DVD equipment. Note that you can not further record or edit on a finalized disc. When you finalize a DVD+RW/DVD-RW (Video mode)/DVD+R/DVD-R (Video mode), a DVD menu will be automatically created, which can be displayed on other DVD equipment. Before finalizing, check the diff erences between the disc types in the table below.

Differences between the disc types

1 Insert a disc. 2 Press SYSTEM MENU while the reco rder is

in stop mode.

The System Menu appears.

3 Select “Disc Setting,” and press ENTER.

The “Disc Setting” display appears.

4 Select “Disc Finalize,” and press ENTER.

The display asks for confirmation.

Discs are automatically finalized when removed from the recorder. You can e dit or record on the disc even after finalizing.

Finalizing is unnecessary when playing a disc on VR format compatible e quipment. Even if your other DVD equipment is VR format compatible, you may need to finalize the disc, especially if the recording time is short. After f inalizing, you cannot edit or record on the disc. If you want to edit or record on it again, unfinalize or reformat the disc (page 64). Note however, that reformatting a disc erases all its contents.

Finalizing is necessary in order to play on equipment other than this recorder. After finalizing, you cannot edit or record on the disc. If you want to edi t or record on it again, unfinali ze or reformat the disc (page 64). Note however, that reformatting a disc erases all its contents.

Finalizing is necessary in order to play on equipment other than this recorder. The finalized discs can be played on other VR mode compatible playe rs. After finalizing, you cannot further edit or record on the disc.

Finalizing is necessary in order to play on equipment other than this recorder. After finalizing, you cannot further edit or record on the disc.

Video

11 22 33

44 55 66

77 880099

SYSTEM

M/m/</,, ENTER

Z OPEN/

Disc Setting

10:10 AM

Disc Name :

Disc Protect : Not Protected

Disc Format : VR Mode

Disc Finalize : Unfinalized

Disc Information

Erase All Titles

Setup

Disc Setting

Edit

Title List

Timer

Dubbing

Do you want to finalize this disc ?

UnfinalizeFinalize

Editing

5 Select “Finalize,” and press ENTER.

The display asks for confirmation again.

6 Select “OK,” and press ENTER.

The recorder starts finalizin g the disc.

To turn off the display

Press SYSTEM MENU.

To unfinalize a DVD-RW

If you cannot record or edit on a DVD-RW that has been finalized, unfinalize the disc by selecting “Unfinalize” in step 5 above.

z Hints

•You can check whether the disc has been finalized or not. If you cannot select “Finalize” in step 5 above, the disc has already been finalized.

•To check the disc information, select “Disc Information” in the “Disc Setting” display and pres s ENTER. See page 64 for details.

Notes

•Depending on the condition of the disc, the recording, or the DVD equipment, discs may not play even if the discs are finalized.

•The recorder may not be able to finalize a disc if it was recorded on another recorder.

Using the Auto Finalize function

If the recording exceeds 30 % of the disc capacity, the recorder automatically finalizes DVD-RWs (Video mode), DVD-Rs (Video mode), and DVD+Rs: –when you eject the disc by pressing Z OPEN/

CLOSE immediately after you stop recor ding by pressing x STOP.

–when all the timer recordings are finished. –if the disc becomes full during recording. To turn on this function, set “Auto Finalize” to “On” in the “Features” setup (page 85).

Notes

•It may take a few minutes for the recorder to finalize a disc.

•A disc once finalized cannot be recorded or edited.

• DVD-Rs (Vidoe mode)/DVD+Rs cannot be unfinalized.

•For discs where erasing titles/chapters does not free up disc space (page 59), the Auto Finalize function activates if the total amount of r ecording before erasing exceeds 30 % of the disc capacity.

•The Auto Finalize function does not wor k for Onetouch Timer Recording (page 50) or SynchroRecording (page 54).

Disc will be finalized.

Do you want to continue ?

CancelOK

RWVideo

RVideo

DV/D8 Dubbing (DV/D8 t DVD)

Before DV/D8 Dubbing

This section explains dubbing with a DV camcorder via the DV IN jack on the front panel. If you want to dub by way of the LINE IN jacks, see “Recording From a VCR or Similar Device” on page 56.

About the DV IN jack

The DV IN jack on this recorder conforms to the i.LINK standard. You can connect any other equipment that has an i.LINK (DV) ja ck, and record digital s ignals. For more information about i.LINK, see “About i.LINK” on page 96.

z Hint

If you plan to do additional editing on a disc after the initial dub, use the DV IN jack and record on a DV D-RW (VR mode) or DVD-R (VR mode). Note that erasing unwanted scenes does not free up disc space for DVD-Rs (VR mode).

Notes

•The DV IN jac k is for input only. It will not output signals.

•You cannot use the DV IN jack when: –your DV camcor der does not work with this recorder.

Connect the camcorder to the LINE IN jack and follow the instructions of “Recording From a VCR or Similar Device” on page56.

–the input signal is not in DVC-SD format. Do not

connect a MICROMV format DV camcorder even if

it has an i.LINK jack. –the input signal is in HDV (1080i) format. –the images on the tape contain copy protection

signals, which limit recording.

Connecting a DV Camcorder to the DV IN Jack

You can connect a DV camcorder to th e DV IN jack on the recorder to record or edit from a DV / D8 format tape. Operation is straightforward because the DVD recorder will fast forward and rewind the tape for you – you do not need to operate your DV camcorder. Refer to the instruction manual supplied with the DV camcorder as well before connecting .

LINE 2 IN DV IN

ONE-TOUCH DUBBING

REC

VIDEO

(MONO)

AUDIO R

DV IN

DVD recorder

to DV IN

: Signal flow

i.LINK cable (not supplied)

to DV output

DV camcorder

1-16

DV/D8 Dubbing (DV/D8 t DVD)

Dubbing From a DV/D8 Format Tape to a DVD

You can simply record the entire contents of a DV/ D8 format tape onto a disc. The recorder controls the DV camcorder for the whole process. You can also select the scenes on the tape u sing the onscreen display. See “Dubbing selecte d scenes” on page 70.

◆How titles and chapters are created

The dubbed contents on the disc become one title, and the title is then divided into chapters at either 5 or 15-minute intervals, according to the “DVD Auto Chapter” setting of “Features” in the “Setup” display.

Notes

•To play the dubbed disc on other DVD equipment, finalize the disc (page66). If you set “Auto Finalize” to “On” in the “Features” setup (page 85), the Auto Finalize function works for DVD-RWs (Video mode), DVD-Rs (Video mode) and DVD+Rs after dubbing. For details, see page 67.

•Do not co nnect the (USB) jack at the same time.

Place a recordable disc on th e disc tray.

About inserting discs, see page 49 for details.

Insert the source DV/D8 format tape into your DV camcorder, and set th e camcorder to video playback mode.

Press INPUT repeatedly to sel ect “DV.”

Press REC MODE repeatedly to select the recording mode.

Set the “DV/D8 Audio Input” setting in the “Audio” setup (page 84).

Select the desired audio if multiple audio channels are recorded on the tape.

Press ONE-TOUCH DUBBING on the recorder.

The recorder rewinds the tape in the DV camcorder and then starts recording the tape contents from the beginning. When playback of the tape stops, One Touch Dubbing ends automatically.

To stop recording

Press x STOP. Note that it may take a few seconds for the recorder to stop recording.

Notes

•During dubbing, timer recordings are unavailable.

•You c annot record the date, time, or contents of a DV/ D8 format tape onto the disc.

•If you record from a DV/D8 format tape with a soundtrack that is recorded in multiple sa mpling frequencies (48 kHz, 44.1 kHz, or 32 kHz), no sound, or an unnatural sound may be output when passing the sampling frequency switch point on the disc.

•The recorded picture may be momentarily affected if the picture size of the source image changes, or if there is nothing recorded on the tape.

•Nois e may occur if you switch the audio sampli ng mode (48 kHz/16 bits t 32 kHz/12 bits).

Video

11 22 33

44 55 66

77 880099

REC MODE

INPUT

SYSTEM

M/m/</,, ENTER

x STOP

REC

ONE-TOUCH DUBBING

,continued

Dubbing selected scenes

You can fast forward, rewind, p lay in slow motion, and stop the tape to select scenes us ing the onscreen display.

1 Follow steps 1 to 5 of “Dubbing From a DV/

D8 Format Tape to a DVD” (page 69).

2 Select “Dubbing” on the System Menu,

and press ENTER.

3 Select “DV/D8 Dubbing,” and press

ENTER.

4 Select “DV/D8 Simple Dubbing,” and

press ENTER.

The “DV Tape Mode” display appear s.

If “DV” or “DV Camera Mode” is displayed, check that the DV camcorder is cor rectly connected, turned on, and set to th e video playback mode.

5 Find the dubbing start point on the tape,

and stop or pause playback.

Press </, to select m, x, X, y, H, or M on the TV screen and press ENTER to find the point, and stop or pause with x or X.

6 Press , to select z on the TV screen, and

press ENTER.

Dubbing starts.

To stop recording

Select x on the TV screen, and press ENTER. Note that it may take a few seconds for the recorder to stop recording.

To turn off the display for DV/D8 dubbing

Press INPUT.

z Hint

If “DV Camera Mode” appears on the screen, you can use z on the TV screen to record the camera image directly on the recorder.

Dubbing

10:10 AM

DV/D8 Dubbing

USB Dubbing

Setup

Disc Setting

Edit

Title List

Timer

Dubbing

DV/D8 Dubbing

10:10 AM

DV/D8 Simple Dubbing

DV/D8 One Touch Dubbing

Setup

Disc Setting

Edit

Title List

Timer

Dubbing

DV Tape Mode

USB Dubbing (USB t DVD)

Before USB Dubbing

This section explains the followi ng dubbing methods via the USB jack:

•Dubbing all the video contents of the connected DVD camcorder to make a backup DVD (page 72).

•Dubbing the selected video contents of the connected HDD camcorder to a DVD (page 73).

•Copying JPEG image files to a DVD (page 75).

◆Connectable USB device s (as of January 2008)

The following Sony devices can be connected to this recorder: DVD camcorder: DCR-DVD108 HDD camcorder: DCR-SR42 Digital still camera: DSC-W200/T100/T20/W80/ W90/H7/H9/G1

z Hint

If your HDD camcorder has no USB jack, use the Handycam Station supplied with the camcorder.

Notes

•During dubbing, do not disc onnect the USB device.

•USB cables exclusi ve for supplying power cannot be used.

•Conn ect the camcorder or digital still camera directly to the recorder, not via a USB hub or other USB device.

•Do not connect the DV IN jack at the same time.

Connecting to the USB jack

You can connect a USB device (DVD camcorder, HDD camcorder, digital still camera, etc.) to the USB jack on the recorder. Also refer to the instruction manual supplied with the connected USB device before con necting.

Turn on the recorder and the USB dev ice.

Connect the USB device to the (USB) jack on the recorder.

Set your USB device to the USB connecting mode, if necessary.

As an example for the HDD camcorder: When “USB SELECT” appear s on the camcorder’s screen, select “ COMPUTER.” For details, refer to the operating instructions supplied with the connected USB device.

LINE 2 IN DV IN

ONE-TOUCH

DUBBING

REC

VIDEO

(MONO)

AUDIO R

DVD recorder

to (USB)

: Signal flow

USB cable (not supplied)

to USB output

DVD camcorder, HDD camcorder, digital still camera, etc.

Dubbing From a DVD Camcorder (DVD Backup)

You can dub all the contents of a DVD in the DVD camcorder to another DVD as a backup copy. Be sure to finalize a so urce DVD before dubbing.

◆Usable discs for backup DVDs

Use a new or blank DVD of the same type as the source DVD.

Notes

•When using a DVD+R/DVD-R , make sure that the disc is new, unformatted, and has not been loaded into the recorder. Since blank d iscs are automatically f ormatted once loaded, you can use them for other purposes, such as timer recording.

•When usi ng a DVD+RW/DVD-RW, use unused or blank discs only, as the operation erases any prerecorded data.

•Inse rt the disc only after step 4 when the disc tray has opened. Otherwise the recorder may automatically format the disc, making it unusable for DVD Backup.

1 Press INPUT repeatedly to select “USB.” 2 Connect your DVD camcorder and set it to

USB connecting mode.

For example, select “ COMPUTER” when “USB SELECT” appears on the camcorder’s screen. Check the USB indicator lights up in the front panel display.

3 Press ONE-TOUCH DUBBING on the

recorder.

The display asks for confirmation. Note that you cannot stop dubbing halfway.

4 Select “Start” and press ENTER.

The disc tray opens.

5 Place a recordable disc, and press Z

OPEN/CLOSE to close the disc tray.

The progress bar display appears, and the recorder starts dubbing the entire contents of the source DVD. Do not disconnect the USB cable while dubbing is in progress. When dubbing is complete, the progress bar disappears.

To dub using the on-screen menu

1 After step 2 above, press SYSTEM MENU. 2 Select “Dubbing,” and press ENTER.

Source DVD (8 cm)

Recordable DVD (12 cm)

DVD+RW DVD+RW

DVD-RW (Video mode) DVD-RW

DVD-RW (VR mode) DVD-RW

DVD-R (Video mode) new DVD-R

DVD+R DL new DVD+R

RWVR-RWVideo

RVideo

11 22 33

44 55 66

77 880099

SYSTEM

M/m/</,, ENTER

INPUT

Z OPEN/

REC

ONE-TOUCH DUBBING

Dubbing

10:10 AM

DV/D8 Dubbing

USB Dubbing

Setup

Disc Setting

Edit

Title List

Timer

Dubbing

No Disc

1-17

USB Dubbing (USB t DVD)

Select “USB Dubbing,” and press ENTER.

Select “DVD Backup,” and press ENT ER. The display asks for confirmation.

Select “Start,” and press ENTER. The disc tray opens.

Place a recordable disc, and press Z OPEN/ CLOSE to close the disc tray. Dubbing starts.

z Hint

To play the dubbed disc, press INPUT repeatedly to select the recorder’s input (LINE1 or LINE2).

Note

During dubbing, timer recordings are unavailable. If the timer is set during dubbing, the timer setting is c anceled.

Dubbing From a HDD Camcorder (Program Dubbing)

You can dub the selected movie files from a HDD camcorder onto a recordable disc.

◆How titles and chapters are created

Note

To play the dubbed disc on other DVD equipment, finalize the disc (page 66). If you set “Auto Finalize” to “On” in the “Features” setup (page 85), the Auto Finalize function works for DVDRWs (Video mode), DVD-Rs (Video mode) and DVD+Rs after dubbing. For details , see page 67.

USB Dubbing

10:10 AM

DVD Backup

HDD-Cam Program Dubbing

Photo Copy

Setup

Disc Setting

Edit

Title List

Timer

Dubbing

No Disc

Video

11 22 33

44 55 66

77 880099

REC MODE

M/m/</,, ENTER

OPTIONS

SET

x STOP

INPUT

,continued

1 Place a recordable disc on the disc tray.

About inserting discs, see page 49 for details.

2 Press REC MODE repeatedly to select the

recording mode.

3 Press INPUT repeatedly to sele ct “USB.” 4 Connect your HDD camcorder and set it to

USB connecting mode.

For example, select “ COMPUTER” when “USB SELECT” appears on the camcor der’s screen. Check the USB indicator lights up in the front panel display.

5 Press ONE-TOUCH DUBBING on the

recorder.

6 Select “Movie (HDD-CAM),” and press

ENTER.

The contents on the HDD camcorde r are listed.

7 Select an album (folder) and press ENTER.

The movie file list appears.

8 Select the movie file to dub, and press

SET.

A number indicating the order in which you selected the file appears. Repeat the step to select all the m ovie files you want to dub. You can select up to 9 files.

9 Press OPTIONS.

The display asks for confirmation.

To return to the previous display, select “Cancel.” To cancel all selections, select “Clear All” an d return to step 8.

Select “Start,” and press ENTER.

Playback starts from the first se lected movie file, and dubbing starts.

To stop dubbing

Press x STOP. Note that it may take a few seconds for the recorder to stop dubbing.

To add dubbing to the same disc

The recorder cannot dub more than 9 movie files at a time. To dub more files, repeat from step 4 above.

REC

ONE-TOUCH DUBBING

Select the item you want to dub.

Movie (HDD-Cam) Photo Copy

00:00:00Stop

AVF_INFO

MP_ROOT

DCIM

10:10 AM

HDD-Cam Program Dubbing

FileAlbum

USB

0/0

00:00:00Stop

Prev Directory

M2U00026.MPG

M2U00027.MPG

M2U00028.MPG

M2U00029.MPG

M2U00030.MPG

10:10 AM

HDD-Cam Program Dubbing

FileAlbum

USB

0/0

101PNV01

Do you want to start dubbing?

Number of items : 2 Source : USB Target

: DVD

Start Clear All

Cancel

USB Dubbing (USB t DVD)

z Hints

•You can also start dubbing from the System Menu. Press SYSTEM MENU to select “Dubbing,” and sel ect “USB Dubbing.” Select “HDD-Cam Program Dubbing” and follow steps from 6 above.

•The recorder can dub movie files that are recorded with an HDD camcorder and have the extension “.MPG.”

•You cannot dub movie files recorded with a digita l still camera.

•To play the dubbed disc, p ress INPUT repeatedly to select the recorder’s input (LINE1 or LINE2).

Notes

•During dubbing, time r recordings are unavailable. If the timer is set during dubbing, the timer setting is canceled.

•Movie files exceeding the disc capacity cannot be dubbed.

•Movie files larger than 2 GB will be dubbed in two divided titles.

•Movie and image files cannot be dubbed together in a single disc.

Copying JPEG Image Files From a Connected Digital Still Camera

You can simply copy all albums containing JPEG image files from a digital still camera or HDD camcorder onto a DVD-RW (Video mode)/DVDR (Video mode). You can also select the albums using the on-screen menu. See “Copying the selected albums” on page 76.

Notes

•Use un used or blank discs for copying. You cannot use a disc containing titles recorded with this recorder. You can add photos to the remaining space on the disc you used for copying photos with this recorder.

•The disc will b e recognized as a DATA DVD after Photo Copy, and can be played on ot her DVD devices capable of JPEG playback if yo u finalize it (page 66). However, note that a DATA DVD may be unrecognizable, depending on the de vice.

•The Auto F inalize function (page 67) does not work for copying photos.

RWVideo-RVideo

11 22 33

44 55 66

77 880099

SET

SYSTEM

M/m/</,, ENTER

OPTIONS

x STOP

INPUT

,continued

Place a recordable disc on the disc tray.

About inserting discs, see page 49 for details.

Press INPUT repeatedly to select “USB.”

Connect the USB device to the (USB) jack on the recorder.

Check that the USB indicator lights up on the front panel display. If not, check the operating instructions supplied with the connected device.

Press ONE-TOUCH DUBBING on the recorder.

Select “Photo Copy,” and press ENTER.

The display asks for confirma tion.

Select “Start” and press ENTER.

The recorder starts dubbing al l the albums in the connected USB device.

To stop copying

Press ENTER to cancel. Note that it may take a few seconds for the recorder to stop copy ing.

z Hint

To play the copied disc, press INPUT repeatedly to select the recorder’s input (LINE1 or LINE2).

Notes

•Do not disconnect the USB cable w hile accessing to the USB device (reading or copying files).

•The recorder can copy up to 254 albums, and up to 49 9 files within a single album. It may take more tha n 30 minutes for the recorder to copy many files at one time. However, this is not a malfunction.

•Do n ot turn off the connected device while copying, as a malfunction may result.

•While co pying, timer recordings are unavailable. If th e timer is set while copying, the timer setting is cance led.

•You cannot r ecord video titles on a disc pre-recorded with photos. If a timer recording is due to start, replace with a recordable disc.

•Up to s even layers of folders stored in the device can be copied. The folders are copied in two la yers on the disc and the folder names will be changed by adding _01, _02, and so on, if they conflict with other names.

Copying the selected albums

You can select the albums using the on -screen menu, and dub them all at once.

Follow the steps 1 to 3 above.

Press SYSTEM MENU.

The System Menu appears.

Select “Dubbing,” and press ENTER.

Select “USB Dubbing,” and press ENTER .

Select “Photo Copy,” and press ENTE R.

If you copy all the albums, select “Copy All Albums” and go to step 8.

REC

ONE-TOUCH DUBBING

Select the item you want to dub.

Movie (HDD-Cam) Photo Copy

Dubbing

10:10 AM

DV/D8 Dubbing

USB Dubbing

Setup

Disc Setting

Edit

Title List

Timer

Dubbing

USB Dubbing

10:10 AM

DVD Backup

HDD-Cam Program Dubbing

Photo Copy

Setup

Disc Setting

Edit

Title List

Timer

Dubbing

Photo Copy

10:10 AM

Copy All Albums

Copy Album

Setup

Disc Setting

Edit

Title List

Timer

Dubbing

1-18

USB Dubbing (USB t DVD)

Select “Copy Album,” and press ENTER.

The album list appears. To view image files contained in the album, select the album and press ENTER.

Press M/m/</, to select the album to copy, and press SET.

A check mark appears in the check box for the selected album. To clear the mark, press SET again. Repeat the step to select all the album s you want to copy.

Press OPTIONS.

The display asks for confirmation.

To return to the previous display, select “Cancel.” To cancel all selections, select “Clear All” and return to step 7.

Select “Start,” and press ENTER.

Copying starts.

To stop copying

Press ENTER to cancel. Note that it may take some time for the recorder to stop copying.

To copy more albums on the same disc

Press SYSTEM MENU, and repeat from step 3 on page 76.

10:10 AM

Photo Copy

Page 1/1

DCIM

USB

101MSDCF

Do you want to start copying?

Number of items : 1 Source : USB Target

: DVD

Start Clear All

Cancel

Settings and Adjustments

Using the Setup Displays

By using the setup displays, you can ma ke various adjustments to items s uch as picture and sound, as well as select a language for the subtitles. The setup displays are used in the fo llowing way.

Note

Playback settings stored on the disc take prior ity over the setup display settings, and not a ll of the functions described may work.

1 Press SYSTEM MENU while the recorder is

in stop mode.

The System Menu appears.

2 Select “Setup,” and press ENTER.

The “Setup” display appears.

3 Select “Clock Set,” “Video,” “Audio,”

“Features,” “Options,” or “Easy Setup,” and press ENTER.

The selected setup display appears. Example: “Video” setup

4 Select the item you want to set up, and

press ENTER.

Available options for the item appear. Example: “TV Type”

M/m/</,, ENTER

11 22 33

44 55 66

77 880099

SYSTEM

O RETURN

10:10 AM

Title List (Original)

Press ENTER :

Title Menu for DVD Title List.

Setup

Disc Setting

Edit

Title List

Timer

Dubbing

10:10 AM

Clock Set

Video

Audio

Features

Options

Easy Setup

Setup

Disc Setting

Edit

Title List

Timer

Dubbing

Setup

Video

10:10 AM

TV Type

Resolution (HDMI)

Video (HDMI)

Black Level

Picture Control

Progressive

Line1 Input

: 4:3 Letter Box

: Auto

: Y Cb Cr

: On

: Standard

: Off

: Composite

Setup

Disc Setting

Edit

Title List

Timer

Dubbing

Video

10:10 AM

TV Type

Resolution (HDMI)

Video (HDMI)

Black Level

Picture Control

Progressive

Line1 Input

: 4:3 Letter Box

: Auto

: Y Cb Cr

: On

: Standard

: Off

: Composite

Setup

Disc Setting

Edit

Title List

Timer

Dubbing

16:9

4:3 Letter Box

4:3 Pan Scan

Settings and Adjustments

Some items display a dialog box that re quires additional settings. Example: When “Parental” in “Op tions” setup is selected.

Select an option, and press ENTER.

The currently selected option is displayed next to the setup item. Example: When “16:9” is set.

To return to the previous display

Press O RETURN.

To turn off the display

Press SYSTEM MENU.

Clock Setting (Clock Set)

The “Clock Set” setup allows you to make clock settings for the recorder.

Press SYSTEM MENU while the recorder is in stop mode.

Select “Setup,” and press ENTER.

Select “Clock Set,” and press ENTER.

The clock setting display appears.

Press M/m to set the month, and press ,.

Set the day, year, hour, minutes, and AM/PM in sequence. Press </, to select the item to be set, then press M/m to set the item. The day of the week is set automatically.

Press ENTER to start the clock.

10:10 AM

Create the password.

Create the password

Setup

Disc Setting

Edit

Title List

Timer

Dubbing

Video

10:10 AM

Setup

Disc Setting

Edit

Title List

Timer

Dubbing

TV Type

Resolution (HDMI)

Video (HDMI)

Black Level

Picture Control

Progressive

Line1 Input

: 16:9

: Auto

: Y Cb Cr

: On

: Standard

: Off

: Composite

2008

Tue

01 01

10 : 10

10:10 AM

Clock Set

Set the time and date manually.

Hour Min

AM/PM

Month Day Year

Setup

Disc Setting

Edit

Title List

Timer

Dubbing

Video Settings (Video)

The “Video” setup allows you to adjust items related to the image, such as size and color. Choose the settings according to the type of TV, tuner, or decoder connected to the recorder.

1 Press SYSTEM MENU while the recorder is

in stop mode.

2 Select “Setup,” and press ENTER. 3 Select “Video,” and press ENTER.

The “Video” setup appears with the fo llowing options. The default settings are und erlined.

TV Type

Selects the aspect ratio of the conne cted TV (4:3 standard or wide).

Note

Depending on the disc, “4:3 Letter Box” may be selected automatically instead of “4:3 Pan Scan” or vice versa.

Resolution (HDMI)

Selects the type of video signals output from the HDMI OUT jack. When you select “Auto” (default), the recorder outputs video signals of the highest resolution acceptable for your TV. If the picture is not clear, unnatural or not to your satisfaction, try another option that suits the disc and your TV/projector, etc. For details, refer also to the instruction manual supplied with the TV/ projector, etc. The setting is effective only when you connect a HDMI equipped TV to the HDMI OUT jack.

Video (HDMI)

Selects the type of output from the HDMI OUT jack. The setting is effective only when you connect a HDMI equipped TV to the HDMI OUT jack.

16:9 Select this when connecting to a

wide-screen TV or TV with a wide mode function.

4:3 Letter Box

Select this when connecting to a 4:3 screen TV. Displays a wide picture with bands on th e upper and lower portions of the screen.

4:3 Pan Scan

Select this when connecting to a 4:3 screen TV. Automatically displays a wide picture on the entire screen and cuts off the portions that do not fit.

Video

10:10 AM

TV Type

Resolution (HDMI)

Video (HDMI)

Black Level

Picture Control

Progressive

Line1 Input

: 4:3 Letter Box

: Auto

: Y Cb Cr

: On

: Standard

: Off

: Composite

Setup

Disc Setting

Edit

Title List

Timer

Dubbing

Auto Normally, select this.

1920×1080p Sends 1920×1080p video signals.

1920×1080i Sen ds 1920×1080i video signals.

1280×720p Sends 1280×720p video signals.

720×480p Sen ds 720×480p video signals.

Y Cb Cr

Normally, select this when connecting to an HDMI device.

RGB Gives brighter colors and deeper

black. Select this if colors are weak.

16:9

4:3 Letter Box

4:3 Pan Scan

+ 59 hidden pages

Sony RMT-D254A, RDR-GX360 Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual