4-421-872-11(1)
Operating Instructions
Stereo Manual de instrucciones
Headphones
MDR-EX10LP
©2010 Sony Corporation Printed in China
L-shaped 
stereo mini plug
Approx. 1.2 m
S |
M |
L |
2 lines |
3 lines |
4 lines |
|
||
|
|
|
Sectional View |
|
|
Colored parts |
English
Stereo headphones
Features
400 kJ/m3 high power neodymium magnets produce high-resolution treble and midrange with powerful bass
Hybrid silicone rubber earbuds (S, M, L) supplied for secure fitting and long-term wearing comfort
Y-type cord with cord slider to prevent cord tangling
Convenient cord adjuster supplied
How to use (see fig. )
Connect the headphones to a device with the stereo mini jack.
Wear the earpiece marked in your right ear and the one marked in your left ear.
There is a tactile dot on the unit marked to distinguish the left side.
Using the cord slider (see fig. - )
Move up and down to change the split position of the cord.
Installing the earbuds correctly (see fig. )
If the earbuds do not fit your ears correctly, low-bass sound may not be heard. To enjoy better sound quality, change the earbuds to another size, or adjust the earbuds position to sit on your ears comfortably and fit your ears snugly.
If the earbuds do not fit your ears, try another size. When you change the earbuds, install them firmly on the headphones to prevent the earbud from detaching and remaining in your ear.
To check the transparent earbud sizes
The transparent earbud sizes are distinguished by a line pattern (see fig. - ).
To check the black earbud sizes
The black earbud sizes are distinguished by the inside color (see fig. - ).
Black earbud sizes (inside color)
Small |
|
Large |
|
|
|
S |
M |
L |
(Orange) |
(Green) |
(Light blue) |
To detach an earbud (see fig. - )
While holding the headphone, twist and pull the earbud off.
Tip
If the earbud slips and cannot be detached, wrap it in a dry soft cloth.
To attach an earbud (see fig. - )
Push the parts inside of the earbud into the headphone until the projecting part of the headphone is fully covered.
To clean the earbuds
Remove the earbuds from the headphones, and wash them with a mild detergent solution.
Specifications
Type: |
Closed, dynamic |
Driver unit: |
9 mm, dome type (CCAW) |
Power handling capacity: |
100 mW (IEC*) |
Impedance: |
16 Ω at 1 kHz |
Sensitivity: |
100 dB/mW |
Frequency response: |
8 – 22,000 Hz |
Cord: |
Approx. 1.2 m (47 1/4 in), Litz cord Y-type |
Plug: |
L-shaped stereo mini plug |
Mass: |
Approx. 3 g (0.11 oz) (without cord) |
Supplied accessories
Earbuds S (2), M (2), L (2) Card warranty (1) Operating Instructions (1)
* IEC = International Electrotechnical Commission
Design and specifications are subject to change without notice.
Precautions
Please keep your headphones clean at all times especially inside the rubber earbud. (see fig. )
If any dust or ear wax is inside the earbud, you may experience some listening difficulties.
Listening with headphones at high volume may affect your hearing. For traffic safety, do not use while driving or cycling.
The earbuds may deteriorate due to long-term storage or use.
Install the earbuds firmly onto the headphones. If an earbud accidentally detaches and is left in your ear, it may cause injury.
Note on static electricity
In particularly dry air conditions, mild tingling may be felt on your ears. This is a result of static electricity accumulated in the body, and not a malfunction of the headphones.
The effect can be minimized by wearing clothes made from natural materials.
Optional replacement earbuds can be ordered from your nearest Sony dealer.
Loading...