Sony LSPX-W1S Operating Instructions

Download

Printed in Japan

Operating Instructions

Before operating the unit, please read this manual thoroughly and retain it for future reference.

LSPX-W1

4-535-453-13 (2)

Video Projector

WARNING

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

WARNING THIS APPARATUS MUST BE

EARTHED.

WARNING

When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring, or connect the power plug to an easily accessible socket-outlet near the unit. If a fault should occur during operation of the unit, operate the disconnect device to switch the power supply off, or disconnect the power plug.

WARNING

1. Use the approved Power Cord (3-core mains lead) / Appliance Connector / Plug with earthing-contacts that conforms to the safety regulations of each country if applicable.

2. Use the Power Cord (3-core mains lead) / Appliance Connector / Plug conforming to the proper ratings (Voltage, Ampere).

If you have questions on the use of the above Power Cord / Appliance Connector / Plug, please consult a qualified service personnel.

For the customers in the U.S.A.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

All interface cables used to connect peripherals must be shielded in order to comply with the limits for a digital device pursuant to Subpart B of part 15 of FCC Rules.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

If you have any questions about this product, you may call; Sony Customer Information Service Center 1-800-222-7669 or http://www.sony.com/

Declaration of Conformity

Trade Name: SONY Model: LSPX-W1 Responsible party: Sony Electronics Inc. Address: 16535 Via Esprillo,

San Diego, CA 92127 U.S.A.

Telephone Number:858-942-2230

For the customers in the U.S.A. and Canada

This equipment complies with FCC/IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated with at least 20cm and more between the radiator and person’s body (excluding extremities: hands, wrists, feet and ankles).

This device and its antenna(s) must not be co-located or operating with any other antenna or transmitter except Grant condition.

For the customers in Canada

CAN ICES-3 (B)/NMB-3(B)

For the customers in Europe

This product has been manufactured by or on behalf of Sony Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-0075 Jap an. Inquiries related to product compliance based on European Union legislation shall be addressed to the authorized representative, Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or guarantee matters, please refer to the addresses provided in the separate service or guarantee documents.

This Video Projector is classified as a CLASS 2 LASER PRODUCT. This CLASS 2 LASER PRODUCT label is located beside the projection window of the Video Projector.

This label is located beside the projection window of the Video Projector.

För kunderna i Sverige

Denna videoprojektor är klassificerad som en LASERPRODUKT AV KLASS 2. Etiketten LASERPRODUKT AV KLASS 2 är placerad bredvid videoprojektorns projiceringsfönster.

Denna etikett är placerad bredvid videoprojektorns projiceringsfönster.

Caution

The use of optical instruments with this product will increase eye hazard.

For kundene i Norge

Dette utstyret kan kobles til et ITstrømfordelingssystem.

Caution

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

For the customers in Canada

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

For the customers in Europe

Notice for customers: the following information is only applicable to equipment sold in Countries applying EU directives.

С настоящето Сони Корпорация декларира, че LSPX-W1/Видео проектор отговаря на основните изисквания и другите

Bulgarian

Croatian

Czech

Danish

Dutch

English

Estonian

Finnish

съответстващи клаузи на Директива 1999/5/ЕС. Подробности може да намерите на Интернет страницата : http://www.compliance.sony.de/.

Ovime Sony Corporation izjavljuje da je LSPX-W1/Videoprojektor u skladu s osnovnim zahtjevima i ostalim relevantnim odredbama direktive 1999/5/EZ. Dodatne informacije potražite na sljedećoj internet adresi: http://www.compliance.sony.de/

Sony Corporation tímto prohlašuje, že tento LSPX-W1/Video projektor je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Podrobnosti lze získat na následující URL: http://www.compliance.sony.de/

Undertegnede Sony Corporation erklærer herved, at følgende udstyr LSPX-W1/ Videoprojektor overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. For yderligere information gå ind på følgende hjemmeside: http:// www.compliance.sony.de/

Hierbij verklaart Sony Corporation dat het toestel LSPX-W1/Videoprojector in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Nadere informatie kunt u vinden op: http://www.compliance.sony.de/

Hereby, Sony Corporation, declares that LSPX-W1/Video Projector is in compliance with the essential requirements and other relevant provisions of the Directive 1999/5/EC. For details, please access the following URL: http://www.compliance.sony.de/

Sony Corporation kinnitab käesolevaga seadme LSPX-W1/videoprojektor vastavust 1999/5/EÜ direktiivi põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. Üksikasjalikum info: http://www.compliance.sony.de/.

Sony Corporation vakuuttaa täten että LSPX-W1/Videoprojektori on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Halutessasi lisätietoja, käy osoitteessa: http://www.compliance.sony.de/

LSPX-W1/

Greek

Hungarian

Alulírott, Sony Corporation nyilatkozom, hogy a(z) LSPX-W1/ videoprojektor megfelel a vonatkozó alapvető követelményeknek és az 1999/5/EC irányelv egyéb előírásainak. További információkat a következő weboldalon találhat: http:// www.compliance.sony.de/

Latvian

Lithuanian

LSPX-W1/

Norwegian

Polish

Portuguese

Romanian

Slovak

Slovenian

Swedish

Tu rk i sh

Sony Corporation erklærer herved at LSPX-W1/videoprojektor er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF. For flere detaljer, vennligst se: http://www.compliance.sony.de/

Niniejszym Sony Corporation oświadcza, że LSPX-W1/projektor jest zgodny z zasadniczymi wymaganiami oraz innymi stosownymi postanowieniami Dyrektywy 1999/5/WE. Szczegółowe informacje znaleźć można pod następującym adresem URL: http://www.compliance.sony.de/

Sony Corporation declara que este LSPX-W1/Projector de vídeo está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. Para mais informacoes, por favor consulte a seguinte URL: http:// www.compliance.sony.de/

Prin prezenta, Sony Corporation declară că LSPX-W1/Videoproiector respectă cerinţele esenţiale și este în conformitate cu prevederile Directivei 1999/5/EC. Pentru detalii, vă rugăm accesaţi următoarea adresă: http:// www.compliance.sony.de/

Sony Corporation týmto vyhlasuje, že LSPX-W1/videoprojektor spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES. Podrobnosti získate na nasledovnej webovej adrese: http://www.compliance.sony.de/

Sony Corporation izjavlja, da je ta LSPX-W1/video projektor v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES. Za podrobnosti vas naprošamo, če pogledate na URL: http:// www.compliance.sony.de/

Härmed intygar Sony Corporation att LSPX-W1/Videoprojektor står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG. För ytterligare information gå in på följande hemsida: http:// www.compliance.sony.de/

LSPX-W1/

Precautions ......................................... 8

Notes on Installation and Usage ........ 9

Carrying the unit .......................... 9

Unsuitable installation .................. 9

Unsuitable Conditions ................10

Location of Controls

Front .................................................11

Rear/Bottom ..................................... 13

Remote Control ................................14

Connections and Preparations

Checking the Supplied

Accessories ................................... 15

Inserting the Batteries into the Remote

Control ..........................................15

Connecting the AC Power Cord ....... 16

Installing the Unit ............................17

Adjusting the Projection Image ....... 17

Attaching the Bottom Covers ...........22

Attaching the Terminal Door ...........23

Connecting to Video Equipment or a

Computer ......................................24

Connecting the Exclusive

Speakers ........................................26

Selecting the Menu Language ..........27

Projecting

Projecting the Picture .......................28

Turning Off the Power ................28

Watching 3D Video Images ............. 29

Using the 3D Glasses ................. 29

Using the Picture Position ................30

Selecting the Aspect Ratio According to

the Video Signal ............................31

Selecting the Picture Viewing

Mode .............................................33

Using the Menus

Operation through the Menus ...........34

Picture Menu ....................................36

Advanced Picture Menu ...................41

Screen Menu .....................................42

Setup Menu .......................................44

Function Menu .................................46

Installation Menu ..............................48

Information Menu .............................51

About the Preset Memory ...........51

Using Network Features

Displaying the Control Window of the

Unit with a Web Browser ..............52

Operating the Control Window ........53

Switching the Page ......................53

Setting the Access Limitation .....53

Confirming the Information

Regarding the Unit ..................53

Error Handling

Troubleshooting ................................54

About Indicators ...............................57

Message Lists ...................................59

Others

Updating the Software ......................60

About x.v.Color ................................60

About the Simulated 3D Feature ......61

Table of Contents

Cleaning ...........................................61

Specifications ...................................63

Preset Signals .............................64

Input Signals and Adjustment/

Setting Items ...........................66

Compatible 3D Signals ...............67

3D Signals and Adjustment/Setting

Items ........................................67

Aspect Mode ...............................69

Storage Conditions of Adjustment/

Setting Items ...........................69

Installation Distance and Projection

Image Size ....................................71

Dimensions .......................................74

NOTICES AND LICENCES

FOR SOFTWARE USED IN THIS

PRODUCT ....................................76

Index .................................................92

Table of Contents

Precautions

On safety

• Check that the operating voltage of your unit is identical with the voltage of your local power supply.

• Should any liquid or solid object fall into the cabinet, unplug the unit and have it checked by qualified personnel before operating it further.

• Unplug the unit from the wall outlet if it is not to be used for several days.

• To disconnect the cord, pull it out by the plug. Never pull the cord itself.

• The wall outlet should be near the unit and easily accessible.

• The unit is not disconnected to the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off.

• Do not look into the lens while in use.

• Do not place your hand or objects near the ventilation holes. The air coming out is hot.

On preventing internal heat buildup

After you turn off the power with the ?/1 (ON/STANDBY) button, do not disconnect the unit from the wall outlet while the cooling fan is still running.

Caution

This unit is equipped with ventilation holes (intake/exhaust). Do not block or place anything near these holes, or internal heat build-up may occur, causing picture degradation or damage to the unit.

On repacking

Save the original shipping carton and packing material; they will come in handy if you ever have to ship your unit. For maximum protection, repack your unit as it was originally packed at the factory.

On watching 3D video images

Safety precautions

• You should only use the 3D glasses for watching 3D video images.

• If you observe flickering or flashing, turn off the lighting in the room.

• Not for use by children without proper adult supervision.

• Be careful not to pinch your fingers in hinges of the 3D glasses when bending the temple frames.

• Do not drop or modify these 3D glasses.

• If these glasses are broken, keep broken pieces away from your mouth or eyes.

On inspection of light source related parts

Since the unit uses a laser, when performing maintenance or inspection of light source related parts, particular attention and a safe environment are necessary. Be sure to consult with qualified Sony personnel (charged).

On LCD Projector

The LCD projector is manufactured using high-precision technology. You may, however, see tiny black points and/or bright points (red, blue, or green) that continuously appear on the LCD projector. This is a normal result of the manufacturing process and does not indicate a malfunction. Also, when you use multiple LCD projectors to project onto a screen, even if they are of the same model, the color reproduction among projectors may vary, since color balance may be set differently from one projector to the next.

On condensation

If the room temperature where the projector is installed changes rapidly, or if the projector is moved suddenly from a cold to a warm place, condensation in the projector may occur. As the condensation may cause malfunction, be careful in adjusting temperature settings of the air conditioner. If condensation occurs, leave the projector turned on for about four hours before use.

Precautions

Notes on security

• SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND RESULTING FROM A FAILURE TO IMPLEMENT PROPER SECURITY MEASURES ON TRANSMISSION DEVICES, UNAVOIDABLE DATA LEAKS RESULTING FROM TRANSMISSION SPECIFICATIONS, OR SECURITY PROBLEMS OF ANY KIND.

• Depending on the operating environment, unauthorized third parties on the network may be able to access the unit. When connecting the unit to the network, be sure to confirm that the network is protected securely.

• From a safety standpoint, when using the unit connected with the network, it is strongly recommended to access the Control window via a Web browser and change the access limitation settings from the factory preset values (page 53). Changing the password regularly is also recommended.

• Do not browse any other website in the Web browser while making settings or after making settings. Since the login status remains in the Web browser, close the Web browser when you complete the settings to prevent unauthorized third parties from using the unit or harmful programs from running.

Notes on Installation and Usage

Carrying the unit

When carrying the unit, be sure to use three or more people - one person for each side and one person for the front side as in the below illustration. When holding the bottom of the unit, hold it firmly by placing your hand under the inner part as much as possible.

Note

Be sure not to grasp the control panel part.

Unsuitable installation

Do not place the unit in the following situations, which may cause malfunction or damage to the unit.

Poorly ventilated location

Leave space of more than 30 cm (11 inches) from the top or front of the unit.

Notes on Installation and Usage

Hot and humid

On a long fluffy carpet

There are the ventilation holes on the bottom of the unit. It may cause a malfunction if the the ventilation holes are blocked.

Very dusty and extremely smoky locations

• If there is debris, sand, etc. in the legs of the unit, the floor may be damaged.

Unsuitable Conditions

Do not do any of the following while using the unit.

Blocking the ventilation holes (intake or exhaust)

Ventilation holes (exhaust)

Ventilation holes (intake)

Tilting front/rear and left/right

Do not install the unit anywhere other than on a level surface. Installing the unit in such a location may result in uneven color uniformity or reduce the reliability of the effects of the light. If the unit is installed with inclining back and forth, the picture shape on the projection surface is trapezoidal. Install the unit so that the unit and projection surface are arranged in parallel.

Other Note

• Air from air conditioners or the ventilation holes of this unit or other devices, may cause oscillation on the projection surface. Be sure not to install this unit in the area where the air from air conditioners or the ventilation holes of these devices reach to the lens part of this unit.

• The top cover of the projector opens and closes. If you place something beside the unit, place it at a distance more than 1 mm from the unit.

Notes on Installation and Usage

When installing the unit at high altitudes

When using the unit at an altitude of 1,500 m (approx. 4,900 ft) or higher, set “Cooling Setting” on the Setup menu to “High”. Failing to set this mode when using the unit at high altitudes could have adverse effects, such as reducing the reliability of certain components.

Location of Controls

Front

The buttons on the control panel function the same as those on the remote control.

Control panelConnector

Indicators and remote control detector

a WARNING1 indicator (page 57)

b LED indicator (page 18)

c WARNING2 indicator (page 57)

i INPUT button (page 28)

j ?/1 (ON/STANDBY) button

(page 18)

Tip

The door opens by pulling the side of the door.

Location of Controls

d Remote control detector

(page 17)

Connector and control panel

e HDMI 3 connector (page 24)

f LENS button (page 17)

g M/m/</, (arrow)/ (enter)

button (page 34)

h MENU button (page 34)

Front

Others

k Top cover (page 18)

Opens automatically when the unit is turned on, and closes automatically when the unit is turned off.

l Ventilation holes (exhaust)

m Ventilation holes (intake)

n Terminal door (page 23)

Note

The top cover of the projector opens and closes. If you place something on the top cover, it may fall and break or cause a malfunction. If you look through the projection window (lens) while the unit is projecting, the light may damage your eyes. Take special caution when using the unit around children.

Front

Rear/Bottom

Location of Controls

Connectors

a HDMI 1/HDMI 2/HDMI 4

connector (page 24)

b REMOTE connector

Connects to a system for remote control, etc.

c IR IN connector

Inputs signals to control the unit.

d Speaker connector (page 26)

e USB connector (page 60)

f LAN connector (page 52)

CAUTION

For safety, do not connect the connector for peripheral device wiring that might have excessive voltage to this port. Follow the instructions for this port.

Others

g AC IN socket (page 16)

h Projection window (lens)

Projects a video from this window.

i Feet (adjustable) (page 22)

j Ventilation holes (intake)

Rear/Bottom

Remote Control

a LIGHT button

Illuminates the buttons on the remote control.

b Infrared transmitter

c ?/1 (ON/STANDBY) button

(page 18)

d PATTERN button (page 18)

e CALIBRATED PRESET buttons

(page 33)

f PICTURE POSITION button

(page 30)

g INPUT button (page 28)

h RESET button (page 35)

i M/m/</, (arrow)/ (enter)

buttons (page 34)

j MENU button (page 34)

k LENS ADJUSTMENT buttons

(page 19)

l ASPECT button (page 31)

m MOTIONFLOW button (page 38)

n COLOR SPACE button (page 40)

o 3D button (page 29)

p REALITY CREATION button

(page 37)

q COLOR TEMP button (page 38)

r VOLUME +/– button (page 47)

s BLANK button

Turns the video off temporarily. To turn on, press this button again,

t LIGHT OUTPUT +/– button

(page 37)

u MUTING button

Turns the audio off temporarily. To turn on, press this button again.

Remote Control

Connections and Preparations

This section describes how to install the unit, how to connect the equipment from which you want to project a picture, etc.

Checking the Supplied Accessories

Check the carton to make sure it contains the following items:

• Remote control RM-W1 (1)

• Size AA (R6) manganese batteries (2)

• AC power cord (1)

•Plug holder (1)

• Bottom cover (front, large) (1)

• Bottom cover (front, small) (1)

• Bottom covers (side) (2)

• Terminal door (1)

• Adjustment tool (1)

• Operating Instructions (this manual) (1)

Inserting the Batteries into the Remote Control

Push and slide to open.

Insert the batteries E side first.

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. When you dispose of the battery, you must obey the law in the relative area or country.

Connections and Preparations

Installing batteries

Two size AA (R6) batteries are supplied for Remote Control. To avoid risk of explosion, use size AA (R6) manganese or alkaline batteries.

Checking the Supplied Accessories / Inserting the Batteries into the Remote

Caution about handling the remote control

• Handle the remote control with care. Do not drop or step on it, or spill liquid of any kind onto it.

• Do not place the remote control in a location near a heat source, a place subject to direct sunlight, or a damp room.

Connecting the AC Power Cord

1 Plug the AC power cord into the AC

IN socket, then attach the plug holder to the AC power cord.

AC IN socket

AC power cord (supplied)

Plug holder (supplied)

2 Slide the plug holder over the AC

power cord to fix to the unit.

Connecting the AC Power Cord

Installing the Unit

Adjusting the

The installation distance between the unit and a projection surface varies depending on the projection size and whether or not you use the zoom features. Install this unit so that it fits the desired projection size. For details on the distance between the unit and the projection surface (the projection distance) and the size of projected video, see “Installation Distance and Projection Image Size” (page 71).

1 Position the unit so that the unit is

parallel to the projection surface.

Top view

Projection surface

2 Project an image on the projection

surface and adjust the picture so that it fits the projection surface (page 17).

Notes

• When using a projection surface with an uneven surface, stripes may rarely appear on the projection surface depending on the distance between the projection surface and the unit or the zooming magnifications. This is not a malfunction of the unit.

• The projection picture may be distorted if the projection surface is not flat.

Projection Image

Project an image on the projection surface and then adjust the projection image.

Remote control detector

Connections and Preparations

Tips

?/1 (ON/STANDBY), INPUT, MENU,

• The

and M/m/</,/ (joystick) buttons on the front panel of the unit function the same as those on the remote control. The LENS button functions in the same way as the LENS ADJUSTMENT (ZOOM, FOCUS, CORNER CORRECTION) buttons of the remote control.

Installing the Unit / Adjusting the Projection Image

• When adjusting the lens, each time you press the LENS button on the unit, the lens adjustment function switches as follows.

Note

Depending on the installation location of the unit, you may not be able to control it with the remote control. In this case, point the remote control at the remote control detector of the unit.

1 After connecting the AC power cord to

the unit, plug the AC power cord into a wall outlet.

The unit goes into standby mode.

2 Press the ?/1 (ON/STANDBY) button

to turn on the unit.

Image size

(for

maximum

zoom)

147- to 132-inch

132- to 121-inch

121- to 113-inch

113- to 106-inch

* Approximate adjustment value. When

the setting is overwritten in “Picture Position” of the Screen menu (page 42), it cannot be returned to the default setting.

Installation

distance

(from a projection surface to the rear of

the unit)

11 to 17 cm (4.3 to 6.7 inches)

6 to 11 cm (2.4 to 4.3 inches)

3 to 6 cm (1.2 to 2.4 inches)

0 to 3 cm (0 to 1.2 inches)

Destination

for

adjustment*

PICTURE POSITION Custom 1

PICTURE POSITION Custom 2

PICTURE POSITION Custom 3

Default setting

To perform further adjustment or change the image size by using the zoom function, follow the steps 4 to 7.

The top cover opens. The LED indicator lights in white.

Tip

The LED indicator does not light when “Illumination” is set to “Off” on the Installation

menu.

3 Press the PICTURE POSITION

button that matches the projection size.

Adjusting the Projection Image

4 Press the PATTERN button to display

the

lens adjustment window (test

pattern).

To return to the previous screen, press the PATTERN button again.

5 Adjust the picture size.

Press the LENS ADJUSTMENT (ZOOM) button, and adjust the size of the picture by pressing the M/m/</, buttons.

To make the picture larger, press M/,. To make the picture smaller, press m/<.

Tip

When “Lens Control” is set to “Off” on the Installation menu, you cannot adjust the picture size, focus or correct the position by pressing the ZOOM, FOCUS, or CORNER CORRECTION buttons (page 48).

6 Adjust the focus.

Press the LENS ADJUSTMENT (FOCUS) button, and adjust the focus of the center of the picture.

7 Press the LENS ADJUSTMENT

(CORNER CORRECTION) button, and adjust the focus and distortion on the top corner of the picture by pressing the M/m/</, buttons.

Connections and Preparations

When the FOCUS button is pressed after adjusting the picture size by the ZOOM button, focus of the center area is adjusted automatically. For the further adjusting, use the M/m/</, buttons.

Adjusting the Projection Image

8 Check if the upper side and lower side of the picture are parallel.

If not, install the unit in a position parallel to the projection surface (a=b).

Image distortion Installation state to the projection surface

(Top view)

a > b

a < b

9 Check if the lower side of the picture is horizontal.

If not, use the left/right feet (adjustable) to keep the unit level. For details of adjusting the feet, see page 22.

Image distortion Feet adjustment

Adjusting the Projection Image

10 Check if the left side and right side of the picture are vertical.

If not, use the foreground feet (adjustable) to keep the unit vertical to the projection surface. For details of adjusting the feet, see page 22.

Image distortion Installation state to the

11 Repeat steps 5 and 6.

Make the frame of the projection surface rectangular and parallel to the floor to finish the installation.

projection surface

Feet adjustment

(Side view)

Connections and Preparations

c > 90°

c < 90°

Adjusting the Projection Image

To adjust the feet

You can adjust the height by using the six feet at the bottom of the unit.

Attaching the Bottom Covers

Attach the bottom covers to the front in two places and both sides of the unit after installing the unit.

Bottom cover (side)

Fixing nut

Foot height

Adjusting nut

Foot

1 Loosen the fixing nut by turning it to

the right when viewed from the top.

2 Turn the adjusting nut to adjust the

length of the foot.

Extending: Turn the adjusting nut to the right (clockwise) when viewed from the top. Contracting: Turn the adjusting nut to the left (counterclockwise) when viewed from the top.

3 Tighten the fixing nut by turning it to

the left when viewed from the top.

Tips

• Use the supplied adjustment tool for adjusting the feet.

• The height does not change if you turn the foot.

Notes

• Be careful not to catch your finger when turning the fixing nut or adjusting nut.

• You can adjust the foot height up to 60 mm. If the foot height is more than 70 mm, the foot may come off and the unit may drop causing an injury.

Bottom cover (front, large)

Bottom cover (front, small)

Bottom cover (side)

Insert the tab of the bottom cover into the hole at the bottom of the unit.

Ta b

Hole

Bottom of the unit

Attaching the Bottom Covers

Attaching the Terminal Door

Insert the opening of the terminal door into the groove on the rear of the unit 1, then push the upper part in 2. The upper part of the door attaches to the magnet on the unit and door is closed.

Opening

Groove

Connections and Preparations

To remove the terminal door

Push the upper part of the door until it clicks 1, then pull it out and upward after opening the upper part 2.

Attaching the Terminal Door

Connecting to Video Equipment or a Computer

You can enjoy high picture quality by connecting a DVD player/recorder, Blu-ray Disc player/ recorder, or PlayStation

equipped with HDMI output to the HDMI input of the unit.

When making connections, be sure to do the following:

• Turn off all equipment before making any connections.

• Use the proper cables for each connection.

• Insert the cable plugs properly; poor connection at the plugs may cause a malfunction or poor picture quality. When pulling out a cable, be sure to pull it out from the plug, not the cable itself.

• Refer to the operating instructions of the connected equipment.

Rear of the unit

Computer

Equipment with HDMI output connectors

Front of the unit

to HDMI output

: Video signal flow Use a high-speed HDMI cable on which the cable type logo

Connecting to Video Equipment or a Computer

HDMI cable (not supplied)

is specified. (Sony products are recommended.)

Notes

• Use a high-speed HDMI cable. With a standard HDMI cable, images of 1080p, DeepColor, 3D video and 4K video may not be displayed properly.

• When connecting an HDMI cable to the unit, make sure the input of the unit and the v mark on the connector of the cable are faced at each other.

• If the picture from equipment connected to the unit with an HDMI cable is not correct, check the settings of the connected equipment.

• If you set your computer to output the signal to both the computer’s display and this equipment, the picture of the equipment may not appear properly. Set your computer to output the signal to only the external monitor. For details, refer to the operating instructions supplied with your computer. For settings of the computer, consult with the manufacturer of the computer.

V mark on the upper part of the HDMI

Connections and Preparations

Connecting to Video Equipment or a Computer

Connecting the Exclusive Speakers

You can output the sound that is input to the unit from the exclusive speakers, and enjoy the sound.

Speaker (right)

: Audio signal flow

Note

Set “Speaker” to “On” on the Function menu to output the sound from the speakers.

Rear of the unit

Speaker cord

Speaker (left)

Connecting the Exclusive Speakers

Selecting the Menu Language

The factory setting for the language for displaying menus, messages, etc. is English. To change the on-screen language, proceed as follows:

b Press M/m to select “

Language,” then press , or .

1 Press MENU to display the menu.

The menu window appears.

2 Select the menu language.

Connections and Preparations

c Press M/m/</, to select a

language, then press , or .

3 Press MENU to turn off the menu

window.

a Press M/m to select the Setup

menu, then press , or .

Selecting the Menu Language

Projecting

This section describes how to operate the unit to view a picture from the equipment connected to the unit. It also describes how to adjust the quality of the picture to suit your taste.

Projecting the Picture

1 Turn on both the unit and the

equipment connected to the unit.

2 Press INPUT to display the input

palette on the projection surface.

3 Select the equipment from which you

want to display images.

Press INPUT repeatedly or press M/m/

(enter) to select the equipment from

which to project.

Turning Off the Power

1 Press the ?/1 (ON/STANDBY)

button.

The message “POWER OFF?” appears.

2 Press the ?/1 (ON/STANDBY) button

again before the message disappears.

The top cover closes automatically, the fan stops, and the LED indicator turns off.

You can disconnect the AC power cord.

Notes

• Never disconnect the AC power cord while the unit is turned on.

• The LED indicator does not change when “Illumination” is set to “Off” on the Installation menu,

• It may take several minutes to turn the LED indicator off after the top cover is closed due to the adjusting of the unit.

You can turn off the unit by holding the ?/1 (ON/STANDBY) button for about 1 second, instead of performing the above steps.

Example: To view the picture from the video equipment connected to the HDMI 1 connector of this unit.

Tips

• When “Status” is set to “Off” on the Setup menu, the input palette does not appear.

Press the INPUT button to switch between input terminals sequentially.

• You can change the language for the menu

and on-screen displays in “Language” on the Setup menu (page 44).

Projecting the Picture

Watching 3D Video Images

You can enjoy powerful 3D video images, such as from 3D games and 3D Blu-ray Discs, using the optional Active 3D Glasses (TDG-BT500A).

Adjusting/Setting the 3D functions

You can adjust/set the 3D functions by pressing the 3D button on the remote control or with the “3D Settings” of the Function menu. For details, see “3D Settings” (page 46).

Using the 3D Glasses

1 Turn on the HDMI equipment for 3D

compatibility connected to the unit, then play the 3D content.

For details on how to play 3D content, refer to the operating instructions for the connected equipment.

2 Turn on the unit and project the 3D

video image.

For details on how to project the image, see “Projecting the Picture” (page 28).

3 Turn on the 3D glasses, and then put

them on so that they fit comfortably.

For details on how to use the 3D glasses, see “Using the 3D Glasses” (page 29).

Tips

• The factory default setting for “2D-3D Display Sel.” is “Auto” to allow projecting 3D video images automatically when the unit detects 3D signals.

• To convert 3D video images to 2D video images, set “2D-3D Display Sel.” to “2D” (page 46).

Notes

• It may not be possible to display 3D video image, depending on the type of signal. Set the “2D-3D Display Sel.” to “3D,” and “3D Format” to “Side-by-Side” or “Over-Under” to suit the format of the 3D content you want to watch (page 46).

• Use the 3D glasses within the communication range (page 29).

• There are differences in perception of 3D video images among individuals.

• When the temperature of the usage environment is low, the 3D effect may be diminished.

1 Turn on the 3D glasses, and register

them on the unit.

For details on how to register the 3D glasses, refer to the operating instructions supplied with the 3D glasses.

Projecting

2 Put on the 3D glasses.

Precautions for use

Misoperation may occur if:

• The viewing position is too far from the projector

• There are other communication devices, such as a wireless LAN (IEEE802.11 b/g/ n) or a microwave with a bandwidth of 2.4 GHz, near the unit

3D glasses communication range

The following figure indicates the communication range of the 3D glasses. If you try to watch 3D video images from a distance greater than the communication range or install the unit outside the communication range, the 3D glasses may not be able to display the images properly. Also, the distance varies depending on the environment of the room and installation environment of the unit.

Watching 3D Video Images

Top v iew

10 m (33 ft)

Projection surface

10 m (33 ft)

Using the Picture Position

You can recall the stored lens settings (lens zoom, lens focus, lens corner correction) and aspect ratio. Use this function for changing projection image size of multiple pictures, etc.

Side view

Projection surface

Projector

10 m (33 ft)

Projector

10 m (33 ft)

1 Press one of the PICTURE

POSITION [Custom 1], [Custom 2], and [Custom 3] buttons.

The picture position that you pressed is recalled.

Tip

Store or delete the lens settings in the “Picture Position” of the Screen menu (page 42).

Notes

• If you press any button on the remote control or the unit while the lens is moving, the lens stops. In this case, select the lens position again or adjust the lens manually.

• The Picture Position function is not guaranteed to reproduce the lens settings precisely.

• When you use the subtended angle of two or more aspects using lens zoom, install the unit within the specified parameters referring to “Installation Distance and Projection Image Size” (page 71).

Using the Picture Position

Selecting the Aspect Ratio According to the Video Signal

You can select an aspect ratio best suited for the video signal received.

Press ASPECT.

Each time you press the button, you can select the “Aspect” setting.You can also select it using the menu (page 43).

ASPECT button

Original image (for 16:9 display) Recommended setting and resultant images

1.85:1 Zoom

1.85:1

Squeezed 1.85:1

2.35:1 Zoom

2.35:1

Squeezed 2.35:1

Projecting

Selecting the Aspect Ratio According to the Video Signal

Original image (for 16:9 display) Recommended setting and resultant images

Normal

1.78:1 (16:9)

1.33:1 (4:3)

1.33:1 (4:3) with side panels

Stretch

Squeezed

Notes

• Selectable aspect modes vary depending on the input signal (page 69).

• The aspect cannot be selected when a computer signal is input, a signal with a resolution of 4096 × 2160 is input (page 64), or “V Keystone” is set to other than “0” on the Installation menu.

Notes on switching the “Aspect” setting

• Select the aspect mode taking into account that changing the aspect ratio of the original picture will provide a different look from that of the original image.

• Note that if the unit is used for profit or for public viewing, modifying the original picture by switching the aspect may constitute an infringement of the rights of authors or producers, which are legally protected.

Selecting the Aspect Ratio According to the Video Signal

Selecting the Picture Viewing Mode

You can select the picture viewing mode that best suits the type of video source or room conditions. You can save and use different preset modes for 2D/3D respectively.

Press one of the CALIBRATED PRESET buttons.

Setting items Description

CINEMA FILM 1 Picture quality suited to reproducing the highly dynamic and

clear images typical of master positive film.

CINEMA FILM 2 Picture quality suited to reproducing the rich tone and color

typical of a movie theater, based on the tones changed for FILM

REF A picture quality setup suitable for when you want to reproduce

faithfully the original image quality, or for enjoying image quality, without any adjustment.

TV Picture quality suited for watching TV programs, sports,

concerts, and other video images.

PHOTO Ideal for projecting still images taken with a digital camera.

GAME Picture quality suited to gaming, with well-modulated colors

and fast response.

BRT CINE Picture quality suited for watching movies in a bright

environment, such as a living room.

BRT TV Picture quality suited for watching TV programs, sports,

concerts, and other video images in a bright environment, such as a living room.

USER Adjusts the picture quality to suit your taste then saves the

setting. The factory default setting is the same as “REF.”

CALIBRATED PRESET buttons

Projecting

Selecting the Picture Viewing Mode

Using the Menus

This section describes how to make various adjustments and settings using the menus.

Operation through the Menus

The unit is equipped with an on-screen menu for making various adjustments and settings. If you select an item name followed by an arrow (B), the next menu window with setting items appears.

1 Press MENU.

The menu window appears.

2 Press M/m to select a menu item, and

press , or .

3 Press M/m to select an item you want

to set or adjust and press , or .

The setting items are displayed in a popup menu, in a setting menu, in an adjustment menu or in the next menu window.

Pop-up menu

Setting items

The items that can be set or adjusted with the selected menu appear. The item presently selected is shown in white.

Operation through the Menus

Setting menu

Adjustment menu

Next menu window

Setting items

4 Make the setting or adjustment of an

item.

To reset the picture that has been adjusted

Select “Reset” from the Picture menu.

When the screen display appears, select “Yes” using < and press . All of the following settings are reset to its factory preset value: “Reality Creation,” “Cinema Black Pro,” “Motionflow,” “Contrast,” “Brightness,” “Color,” “Hue,” “Color Temp.,” “Sharpness,” and “Expert Setting” on the Picture menu

To reset the items that have been adjusted

Select an item in the menu screen, and display the pop-up menu, the setting menu, or the adjustment menu. Press RESET on the remote control to reset only the selected settings to its factory preset value.

Note

The RESET button on the remote control is available only when the adjustment menu or the setting menu is selected.

Using the Menus

When changing the adjustment level

To increase the value, press M/,. To decrease the value, press m/<. Press to store the setting and restore the original menu screen.

When changing the setting

Press M/m to change the setting. Press to restore the original screen. You can restore the original screen using < depending on the selected item.

To clear the menu

Press MENU.

Operation through the Menus

Picture Menu

The Picture menu is used for adjusting the picture.

Note

These items may not be available, depending on the type of input signal. For details, see “Input Signals and Adjustment/Setting Items” (page 66).

Item names in brackets represent those printed on the remote control.

Setting items Description

Calib. Preset [CALIBRATED PRESET]

You can select the picture viewing mode that best suits the type of video source or the environment. You can save and use different preset modes for 2D/3D respectively. Cinema Film 1: Picture quality suited to reproducing the highly dynamic and clear images typical of master positive film. Cinema Film 2: Picture quality suited to reproducing the rich tone and color typical of a movie theater, based on the tones changed for Cinema Film 1. Reference: A picture quality setup suitable for when you want to reproduce faithfully the original image quality, or for enjoying image quality, without any adjustment. TV: Picture quality suited for watching TV programs, sports, concerts, and other video images.

Photo: Ideal for projecting still images taken with a digital camera. Game: Picture quality suited to gaming, with well-modulated colors and

fast response. Bright Cinema: Picture quality suited for watching movies in a bright environment, such as a living room. Bright TV: Picture quality suited for watching TV programs, sports, concerts, and other video images in a bright environment, such as a living room. User: You can adjust the picture quality to suit your taste, and save the setting. The factory default setting is the same as “Reference.”

Tip

Any adjustments to picture quality settings are saved for each input.

Picture Menu

Setting items Description

Reset Resets all currently selected Calib. Preset mode settings to their default

Reality Creation [REALITY CREATION]

Cinema Black Pro

Laser Light Setting [LIGHT OUTPUT]

Contrast Enhancer Corrects the level of bright and dark parts automatically to optimize

values (page 35).

Tip

Reset does not affect settings saved for the Custom 1 to 5 items of “Color Temp.”

Adjusts the detail and noise processing of images. (Super-resolution function)

On: Adjusts the settings of “Reality Creation.”

Database: Select “Normal” or “Mastered in 4K.”

“Mastered in 4K” provides image quality suitable for Blu-ray Disc™ “Mastered in 4K” released by Sony Pictures Home Entertainment. This setting is available when inputting the 1080/24p signal. Resolution: When you increase the setting value, the texture and detail of the picture become sharper. Noise Filtering: When you increase the setting value, the noise (picture roughness) becomes less prominent. Test: On /O f f : Switches “On” and “Off” at a certain frequency to check the effect of “Reality Creation.”

Tip

The display position of the status during the test works together with the “Menu Position” setting (page 44).

Off: The “Reality Creation” function is not applied.

Dynamic Control: Adjusts the range of movement of the laser light

control.

Full: Automatically optimizes the laser light control and signal processing according to the brightness level of the input source. This results in a bright and high contrast image. Limited: Suppresses the movement and brightness of the laser light control, making the picture quality suitable for viewing in a dark room.

Off: The “Dynamic Control” function is not applied.

Output: The higher the setting, the brighter the picture. The lower the

setting, the darker the picture. You can adjust by the LIGHT OUTPUT +/– button on the remote control.

Tip

After adjusting “Output,” set “Dynamic Control” according to the brightness of the room and the picture itself.

contrast according to a scene. Increases image sharpness and makes image dynamic.

High/Middle/Low: You can adjust the contrast enhancer. Off: The contrast enhancer function is not applied.

Using the Menus

Picture Menu

Setting items Description

Motionflow [MOTIONFLOW]

Contrast Adjusts the contrast.

Brightness Adjusts the brightness of the picture.

Color Adjusts the color density.

Hue Adjusts the color tone.

Color Temp. [COLOR TEMP]

Sharpness Sharpens the outline of the picture, or reduces the noise.

Smooth High: Provides smoother picture movement; especially effective for film-based content.

Smooth Low: Provides smoother picture movement for standard use. Impulse: Reproduces original picture quality. Provides cinema-like

picture, which may flicker. Combination: Reduces motion blur while maintaining brightness for high-speed picture content. True Cinema: Images, such as a movie created in 24 frames per second, are reproduced at the original framerate. Off: The “Motionflow” function is not applied.

Tips

• Select “Off” if the selected “Smooth High,” “Smooth Low,” “Impulse,” “Combination,” or “True Cinema” results in a distorted picture.

• Depending on the picture content, you may not see the effect visually even if you have changed the settings.

• Only “Off” or “Impulse” is available when a signal with a resolution of 4096 × 2160 or 3840 × 2160 is input.

Higher values increase the sharpness in images, while lower values decrease the sharpness.

The higher the setting, the brighter the picture. The lower the setting, the darker the picture.

The higher the setting, the greater the intensity. The lower the setting, the lower the intensity.

The higher the setting, the more greenish the picture becomes. The lower the setting, the more reddish the picture becomes.

Adjusts the color temperature. D93: Equivalent to 9,300 K color temperature normally used in TVs. Gives white colors a blue tint. D75: Equivalent to 7,500 K color temperature used as an ancillary standard illuminant. Gives a neutral tint between “D93” and “D65.” D65: Equivalent to 6,500 K color temperature used as a standard illuminant. Gives white colors a red tint. D55: Equivalent to 5,500 K color temperature used as an ancillary standard illuminant. Gives white colors an even redder tint. Custom 1 to 5: Enables you to adjust, set, and store your favorite color temperature. The factory default settings are as follows.

Custom 1: Same as the “D93” color temperature setting. Custom 2: Same as the “D75” color temperature setting. Custom 3: Same as the “D65” color temperature setting. Custom 4: Same as the “D55” color temperature setting. Custom 5: Setting that prioritizes brightness.

The higher the setting, the sharper the picture. The lower the setting, the softer the picture, thus reducing the noise.

Picture Menu

Setting items Description

Expert Setting

NR (Noise Reduction)

MPEG NR (MPEG Noise Reduction)

Smooth Gradation Smooths the gradation of the flat parts of images.

Film Mode According to the film source you have selected, make a setting for

Gamma Correction

Reduces the roughness or noise of the picture. Auto: Detects the noise level to reduce the roughness or noise of the picture automatically. High/Middle/Low: Select a setting according to the roughness or noise of the input signal source. Off: The NR (noise reduction) function is not applied.

Tip

The noise level may not be detected accurately with “Auto” depending on the input signal source. If the picture is unacceptable with “Auto,” select a setting from among “High,” “Middle,” “Low” or “Off.”

Reduces block noise and mosquito noise, particularly in digital signals. Auto: Detects the noise level to reduce the block noise and mosquito noise of the picture automatically. High/Middle/Low: Select a setting according to the block noise and mosquito noise of the input signal source. Off: The MPEG NR (MPEG noise reduction) function is not applied.

Tip

High/Middle/Low: You can adjust the smooth gradation effect. Off: The smooth gradation function is not applied.

playback. Auto: Suitable for reproducing the original picture movement. Normally, set this to “Auto.” Off: Plays back the picture in progressive format without detecting video signals automatically.

Adjusts the response characteristics of the tone of the picture. Select a favorite tone from 10 options.

1.8: Bright Produces a brighter picture overall.

2.0

2.1

2.2

2.4

2.6: Dark Produces a darker picture overall. Gamma 7: Simulates the gamma curve of film. Gamma 8: Increases the sharpness in images. Select this when you

watch in a bright environment, such as a living room.

Gamma 9: Produces a brighter picture than Gamma 8. Gamma 10: Increases the sharpness in images. Select this when you

watch TV programs, etc., in a bright environment, such as a living room. Off: The “Gamma Correction” function is not applied.

Using the Menus

Picture Menu

Setting items Description

Color Correction On: Adjusts Hue, Saturation and Brightness of the selected colors.

Clear White Emphasizes vivid whites.

x.v.Color Set this item when connecting the unit with equipment that supports

Color Space [COLOR SPACE]

Repeat steps 1 and 2 described below to specify the target color. 1 Press M/m to select “Color Select,” then press </, to select the

color you want to adjust among “Red,” “Yellow,” “Green,” “Cyan,” “Blue,” and “Magenta.”

2 Press M/m to select “Hue,” “Saturation” or “Brightness,” then adjust

them to suit your taste using </, while watching the projected picture.

Off: The “Color Correction” effect is not applied.

High/Low: You can adjust the “Clear White” effect. Off: The “Clear White” effect is not applied.

x.v.Color and playing back an x.v.Color video signal.

On: You can play back an x.v.Color video signal. Off: The “x.v.Color” function is not applied.

For details on x.v.Color, see “About x.v.Color” (page 60).

Tip

Setting x.v.Color to “On” disables gamma adjustment. Converts the color space.

BT.709: An ITU-R BT.709 color space, which is used for highdefinition television broadcast or Blu-ray Disc. The color space is equivalent to sRGB. Color Space 1: The color space suited for watching TV programs and video images, such as sports, concerts, etc. Color Space 2: The color space suited for watching TV programs, sports, concerts, and other video images in a bright environment, such as a living room. Color Space 3: The color space suited for watching movies in a bright environment, such as a living room. Custom: You can adjust the color space setting.

Input Lag Reduction

Picture Menu

Reduces the delay of the display for a video. On: Shortens the time to display the input video image; effective for increasing the performance of the display reaction speed when using an external controller, etc. Off: Turns the Input Lag Reduction function off.

Tip

When “Input Lag Reduction” is set to “On,” Motionflow, NR, and MPEG NR cannot be set.

Advanced Picture Menu

You can adjust the gaps in color that have occurred after a long period of use.

Setting items Description

Auto Calibration Pre Check: Checks the color difference against the factory default

settings, before calibration starts.

Adjust: Performs Auto Calibration. Before/After: Toggles the factory default settings and the setting after

the calibration at a certain frequency. You can check the effect of the calibration by monitoring the actual image. Reset: Resets the calibration results, and returns to the factory default settings.

Notes

• Auto Calibration results in relatively coarse calibration. The color settings are not guaranteed to be the same as the factory default values.

• While performing “Pre Check” or “Adjust,” the colors are projected automatically. This is not a malfunction.

• Do not turn off the power or operate the remote control or control panel during “Pre Check” or “Adjust,” as the process may be canceled.

Tips

• dE is an indicator of changing color. The smaller the value of dE, the fewer the changes caused by the color.

• Perform the calibration after the power has been on for more than 30 minutes.

• It takes a few minutes for “Pre Check” or “Adjust” to complete.

• When “Pre Check” or “Adjust” starts, the screen position may shift as the lens returns to its factory default position. After completion, the screen returns to its previous position automatically.

• If the environment, such as the brightness of the room, changes while performing “Pre Check” or “Adjust”, measurement may be affected.

• If the “Pre Check” or “Adjust” function fails, try it again.

Using the Menus

Advanced Picture Menu

Screen Menu

You can set the picture size, aspect mode, etc.

Note

These items may not be available, depending on the type of input signal. For details, see “Input Signals and Adjustment/Setting Items” (page 66).

Item names in brackets represent those printed on the remote control.

Setting items Description

Picture Position [PICTURE POSITION]

You can store up to five combinations of lens settings and aspect ratios. After setting the lens and aspect, select from “1.85:1,” “2.35:1,” “Custom 1,” “Custom 2” or “Custom 3” depending on the subtended screen angle, and after confirming, continue by selecting “Save,” “Delete,” or “Select.” Save: Stores the current lens settings (lens zoom, lens focus, lens corner correction) in the selected position. If a setting is already stored in that position, it is overwritten. Delete: Deletes the stored setting. After the setting is deleted, “1.85:1,” “2.35:1,” “Custom 1,” “Custom 2,” or “Custom 3” in the display changes to “---.” Select: Recalls the settings of the selected position.

Tip

The optimal aspect ratio is preset for each picture position. The aspect ratio can be changed and saved for each picture position.

Notes

• If you press any button on the unit while the lens is moving, the lens stops. In this case, select the lens position again or adjust the lens manually.

• When you use a 2.35:1 or a 16:9 subtended angle with the Picture Position function, make sure that the installation position is suitable (page 30).

• The Picture Position function is not guaranteed to reproduce the lens settings precisely.

Screen Menu

Setting items Description

Aspect [ASPECT]

You can set the aspect ratio of the picture to be displayed for the current input signal (page 31).

1.85:1 Zoom: A 1.85:1 aspect ratio picture is displayed in its original aspect ratio, enlarged so that black bands do not appear at the top and bottom of the projection surface.

2.35:1 Zoom: A 2.35:1 aspect ratio picture is displayed in its original aspect ratio, enlarged so that black bands at the top and bottom of the projection surface are as small as possible. Normal: Input video is displayed in its original aspect ratio, enlarged to fill the projection surface. This mode is suitable for viewing 1.78:1 (16:9) and 1.33:1 (4:3) video. Stretch: Displays video that has been squeezed to 1.33:1 (4:3) as 1.78:1 (16:9) aspect ratio.

Tips

• Selectable aspect modes vary depending on the input signal (page 69).

• The aspect cannot be selected for an input signal from a computer or an input signal with a resolution of 4096 × 2160, or when “V Keystone” on the Installation menu is set to other than 0 (pages 64, 65, 69).

Using the Menus

Screen Menu

Setup Menu

The Setup menu is used to change the factory preset settings, etc.

Setting items Description

Status Sets whether or not the on-screen display is displayed.

Language Selects the language used in the menu and on-screen displays. Menu Position You can change the position to display the menu on the projection

Cooling Setting Sets the unit to operate at the prevailing atmospheric pressure.

Remote Start Sets the Remote Start settings.

Set to “Off” to turn off the on-screen displays except for certain menus, message when turning off the power, and warning messages.

surface. Bottom Left: Displays the menu on the bottom left area of the projection surface.

Center: Displays the menu on the center of the projection surface.

High: Use this setting when using the unit at an altitude of 1,500 m

(approx. 4,900 ft) or higher. Standard: Use this setting when using the unit at normal altitudes.

Tip

When this item is set to “High,” the fan noise becomes slightly louder since the fan speed increases.

On: You can turn on the power from a PC or a terminal which is connected to a network. Off: Turns off the Remote Start function.

Tips

• To use the function, the unit should be connected to the network in advance (page 50).

• To turn on the power with the Remote Start function, a special command should be sent from a PC or a terminal. For details, consult with qualified Sony personnel.

Note

When the Remote Start is set to “On,” the standby power requirement will increase. When Network Management is set to “On,” the Remote Start setting is set to “Off” automatically, and you cannot change the setting.

Setup Menu

Setting items Description

Network Management On: Set when connected to the network and continuously

communicating with the projector control equipment.

Note

When Network Management is set to “On,” the network function is continuously enabled. Set Network Management to “Off” for normal use. If you set to “On,” the power consumption increases.

Power Saving Sets the power saving mode.

Standby: If no signal is input for 10 minutes, power is turned off automatically and the projector goes into standby mode. Off: Disables the power saving function.

Using the Menus

Setup Menu

Function Menu

The Function menu is used for changing the settings of the various functions of the unit.

Setting items Description

3D Settings You can change the settings of the 3D function.

2D-3D Display Sel.

For Switching the video images to “2D” or “3D.” Auto: Displays 3D video images when HDMI signals with 3D information* are input. Displays 2D video images when other signals are input. 3D: Displays 3D video images according to the 3D system selected in “3D Format.” However, when HDMI signals with 3D information are input to the unit, displays 3D video images according to the 3D system of those HDMI signals. 2D: Displays 2D video images. * The 3D information is additional information to differentiate 3D. Some

HDMI signals have additional information to differentiate 3D and some HDMI signals have none.

3D Format: Set the 3D system when the input HDMI signals do not include 3D information.

Simulated 3D: Converts 2D video images to 3D video images. The setting can be made only for input the HD signals. The simulated 3D feature may have limited effect, depending on the video source. There are differences in perception of 3D video images among individuals. Side-by-Side: Select this to display 3D images as two similar images, side-by-side. Over-Under: Select this to display 3D images as two similar images, one above the other.

Tips

• “2D-3D Display Sel.” cannot be set to “3D” for some video sources. For available 3D signals, see “Compatible 3D Signals” (page 67).

• The simulated 3D feature may have limited effect, depending on the projection image size (100 to 120 inches recommended) and the video source.

• The menu display has a ghost while a 3D video image is displayed and is best viewed with the 3D glasses.

Function Menu

Setting items Description

3D Brightness For adjusting the brightness of the picture when watching 3D video

3D Depth Adjust For adjusting the depth of the 3D video images on the projection surface.

Simulated 3D Effect

Dynamic Range Sets the video input level for HDMI 1, 2, 3, and 4 connectors.

Volume [VOLUME]

Speaker When you select “On,” the sound is output from the supplied speakers.

images. You can select the brightness from “High” or “Standard.”

The setting can be made only when a 3D Format other than “Simulated 3D” is selected.

Depth

NormalFront Depth

We recommend that “3D Depth Adjust” be set to “0.” The 3D video images may be difficult to perceive, depending on the setting of “3D Depth Adjust.”

For adjusting the 3D effect when 2D content is converted to 3D video images. You can select the effect from among “High,” “Middle,” and “Low.”

Tip

There are differences in perception of 3D video images converted by the simulated 3D function among individuals.

Auto: Sets the video input level automatically. Limited: The video input level is set for signals of 16-235. Full: The video input level is set for signals of 0-255.

Note

If the video output setting of the connected HDMI device is not set correctly, light and dark parts of the video may appear too light or too dark.

Higher values increase the volume, while lower values decrease the volume.You can make adjustments by pressing the VOLUME +/– button on the remote control.

Tips

• You need to connect the speakers to the unit.

• The “Speaker” setting needs to be set to “On.”

When you do not want to output the sound from the speakers, select “Off.”

Tip

You need to connect the speakers to the unit.

Using the Menus

Function Menu

Installation Menu

The Installation menu is used for changing the installation settings.

Setting items Description

V Keystone Corrects the vertical trapezoidal distortion of the picture.

Lens Control Avoids any operation of the lens such as “Lens Zoom,” “Lens Focus,”

Illumination Changes the brightness of the LED indicator.

Blanking This feature allows you to adjust the displayable region within the four

When the bottom of the trapezoid is longer than the top ( ): Sets a lower value (– direction). When the top of the trapezoid is longer than the bottom ( ): Sets a higher value (+ direction).

Note

Depending on the picture position adjusted with the CORNER CORRECTION feature, the aspect ratio of the picture may change from the original or picture distortion may occur with V Keystone adjustment.

and “Lens Corner Correction,” by mistake.

On: Enables adjustment of the lens. Off: Prevents any adjustment of the lens.

High: The LED indicator lights brightly. Low: The LED indicator lights not so brightly. Off: The LED indicator does not light normally.

directions of the projection surface. Select the edge to adjust by highlighting Left, Right, Top, or Bottom using the M/m buttons. Adjust the amount of blanking using the </, buttons.

Tip

Depending on the aspect ratio setting, right/left blanking may not be available.

Installation Menu

Setting items Description

Panel Alignment This feature allows you to adjust the gaps in the color of characters or

the picture on the projection surface. Adjust: Adjusts the gaps in the colors selecting “Adjust Item” or “Adjust Color.”

Adjust Item: Selects how to make adjustments from below.

Shift: Shifts the whole picture and makes adjustments. Zone: Selects the desired range and makes adjustments.

Adjust Color: Assigns the desired color to adjust the gaps in color.

Select “R” (Red) or “B” (Blue) to make adjustments based on “G” (Green). Pattern Color: Select “R/G” (Red and Green) or “R/G/B” (White, all colors) when “Adjust Color” is “R” (Red). Select “B/G” (Blue and Green) or “R/G/B” (White, all colors) when the “Adjust Color” is “B” (Blue). Adjust: The shift adjustment and zone adjustment of the color selected in “Adjust Color” can be made with the </,, M/m buttons.

When “Shift” is selected: Assign the settings of the horizontal direction (H) with the </, buttons and the vertical direction (V) with the M/m buttons on the shift adjustment screen.

When “Zone” is selected: Select the position to adjust with the </ , buttons for the horizontal position (H position) and the M/m buttons for the vertical position (V position), then press .

Using the Menus

Set the amount to adjust with the </, buttons for the horizontal direction (H direction) and with the M/m buttons for the vertical direction (V direction). You can select the position to adjust again by pressing .

Reset: Returns to the factory settings.

Preset: The optimized data has been preset.

Note

Depending on the adjustments made above, colors may become uneven or the resolution may change.

Installation Menu

Setting items Description

Network Setting Perform internet protocol settings.

IPv4 Setting IP Address Setup: Selects the IP address setting method.

IPv6 Information Displays the IPv6 information.

Auto (D HCP): The IP address is assigned automatically from the DHCP server such as a router. Manual: Specifies the IP address manually. When “Manual” is selected for “IP Address Setup,” select the item with the </, buttons and input the value with the M/m buttons. When all items are entered, select “Apply,” and then press the button. The entered settings will be registered.

IP Address: Sets the unit’s IP address. Subnet Mask: Sets the unit’s subnet mask. Default Gateway: Sets the unit’s default gateway. MAC Address: Displays the unit’s MAC address. This cannot be

changed. Apply: Enables the IP address that is set manually.

When you set the IPv6 IP address, set it on a Web browser (page 52).

Installation Menu

Information Menu

The Information menu displays the model name, serial number, input signal type, and software version.

Model name

Serial No.

Signal type

Software version

Items Description

Model Name Displays the model name Serial No. Displays the serial number. Signal type Displays the type of the input signal. When input signals with 3D

information are input, the type of input signals and the 3D format are displayed.

Software Version Displays the software version.

Note

You cannot adjust or change the displays listed above.

Using the Menus

About the Preset Memory

This unit has default image data to adjust preset data for input signals appropriately according to the signals shown in “Preset Signals” (page 64) (the preset memory). When the preset signal is input, the unit automatically detects the signal type and recalls the data for the signal from the preset memory to adjust it to an optimum picture. The signal type is displayed in the Information menu.

Note

Depending on the computer input signal, parts of projection image may be hidden or displayed incorrectly.

Information Menu

Using Network Features

Connection to the network allows you to operate the following features:

• Checking the current status of the unit via a Web browser.

• Making the network settings for the unit.

• Network monitoring and controlling with control protocol (SDAP [Advertisement], SDCP [PJ Talk], DDDP [AMX], Crestron RoomView, Control4).

Notes

• When connecting this projector with the network, consult with the person who sets up the network. The network must be secured.

• When using this projector connected with the network, access the Control window via a Web browser and change the access limitation of the factory preset values (page 53). It is recommended to change the password regularly.

• When the setting on the Web browser is completed, close the Web browser to log out.

• The menu displays used for the explanation below may be different depending on the model you are using.

• Supported Web browsers are Internet Explorer 8/9/10/11.

• The menu displays only English.

• If the browser of your computer is set to [Use a proxy server] when you have access to the unit from your computer, click the check mark to set accessing without using a proxy server.

• AMX DDDP is not compatible with IPv6.

• These network functions are available when the unit is turned on.

3 Start a Web browser on the computer,

Displaying the Control Window of the Unit with a Web Browser

enter the following in the address field, then press the Enter key on your computer.

http://xxx.xxx.xxx.xxx (xxx.xxx.xxx.xxx: IP address for the unit)

1 Connect the LAN cable.

LAN cable (straight type) (not supplied)

Hub, router, etc.

LAN Connector

2 Set the network settings for the unit

using “Network Setting” on the Installation menu (page 50).

Displaying the Control Window of the Unit with a Web Browser

When connecting by the IPv6 address

http://[xxxx:xxxx:- xxxx]

You can confirm the IP address of the unit under “Network Setting” on the Installation menu.

The following window appears in the Web brow ser:

Once you make the network settings, you can open the Control window only by performing step 3 of this procedure.

Operating the Control Window

Switching the Page

Entry area for [Administrator]

Entry area for [User]

When you change the password, input a new password after deleting the password (*****) that was set.

Note

If you forget your password, consult with qualified Sony personnel.

Click one of the Page Switching buttons to display the desired setting page.

Page Switching buttons

Setting the Access Limitation

You can limit a user for accessing any particular page.

Administrator: Allowed access to all

pages

User: Allowed access to all pages

except the Setup page Set under [Password] of the Setup page. When you access the Setup page for the first time, enter “root” for user name and enter “Projector” for password. The name of the administrator is preset to “root.”

Confirming the Information Regarding the Unit

You can confirm the current settings for the unit on the Information page.

Using Network Features

Information area

Operating the Control Window

Error Handling

Troubleshooting

If the unit appears to be operating erratically, try to diagnose and correct the problem using the following instructions. If the problem persists, consult with qualified Sony personnel.

Power

Symptom Cause and Remedy Page

The power is not turned on.

The power is suddenly turned off.

Picture

Symptom Cause and Remedy Page

No picture. Check that the connecting cable is connected to the external

The picture has ghosts. Video images are displayed in 3D. Watch the 3D video

Bright or dark area of the video appears too bright or too dark.

The picture is too dark. Adjust “Contrast” or “Brightness” on the Picture menu

The picture is not clear. Adjust the focus and corner correction of the picture. 19

Check the LED indicators. 57 After the AC power cord is connected, it may take about 10

seconds until the unit is ready to be turned on. Wait a while then turn on the unit.

Check that “Power Saving” in the Setup menu is set to “Standby.”

Set “Power Saving” to “Off.” 45

equipment properly. Depending on the external equipment or connecting cable, the unit may not function correctly via the HDMI 4 connector. In this case, use the HDMI 1/HDMI 2/HDMI 3 connector, then select the input.

Select the input source correctly using the INPUT button. 28 Check that the computer signal is set for output to an

external monitor. If a notebook computer and the signal is output to its display and an external monitor, the external monitor’s image may not be displayed correctly. Set your computer to output the signal to only an external monitor.

images using the 3D glasses, and set “2D-3D Display Sel.” to “3D.” To convert 3D video images to 2D video images, set “2D3D Display Sel.” to “2D.”

This symptom may occur when a signal level other than those of HDMI standard is input. Switch the output level of the connected equipment, or switch the Dynamic Range on the Function menu of the unit.

properly.

Condensation has accumulated on the lens. Leave the unit for about 4 hours with the power on.

29, 46

–

Troubleshooting

Symptom Cause and Remedy Page

The color of characters or the picture is not appropriate.

Image is left on the projection image. (Image retention)

The picture is distorted. Check if the installing projecting surface is not distorted. 17

Select the desired color registration in “Panel Alignment” on the Installation menu.

When high contrast non-moving images are displayed for a long period of time, there may be some image retention on the projection image. This is only a temporary condition. Turning off the power for a while will eliminate the retained image.

Install the unit horizontally. 17 Adjust the picture distortion by the CORNER

CORRECTION button.

On-screen display

Symptom Cause and Remedy Page

On-screen display does not appear.

Set “Status” on the Setup menu to “On.” 44

Sound

Symptom Cause and Remedy Page

There is no sound from the speakers.

Check if the speakers are connected to the unit. 26 Set “Speaker” on the Function menu to “On.” 47

Remote control

Symptom Cause and Remedy Page

The remote control does not work.

Batteries could be weak. Replace them with new batteries. – Insert the batteries with the correct polarities. – If there is a fluorescent lamp near the remote control

detector, the unit may work improperly or inadvertently. Confirm the position of the remote control detector on the

unit.

–

Error Handling

Troubleshooting

3D video images

Symptom Cause and Remedy Page

The video image does not seem like 3D video images.

Check if the 3D glasses are turned on. 29 Make sure that the battery in the 3D glasses is sufficiently

charged. Set “2D-3D Display Sel.” to “Auto” or “3D.” 46 Check if the input signals are compatible 3D signals. 67 The 3D signals may not be input depending on the

specifications of the connected AV selector/AV amplifier/ external equipment. If the 3D signal is not input, confirm the specifications and/or settings of the AV selector/AV amplifier/external equipment.

When the viewing position is too far from the unit, the 3D glasses may not be able to display the images properly.

The projection image size is not appropriate. Set the zooming magnification to low or watch the image from farther away from the projection surface.

For details, see “Precautions for use” of “Using the 3D Glasses.”

Others

Symptom Cause and Remedy Page

The fan is noisy. Check the setting of “Cooling Setting” on the Setup

menu. Make sure that the room temperature is not too high. – Check the installation requirements of the unit.

Fan speed increases to maintain the product reliability of the projector’s components in a room where the temperature is higher than normal. The fan noise becomes slightly louder in these rooms. The approximate normal temperature for the unit is 25°C (77°F).

–

Troubleshooting

About Indicators

The WARNING1 or WARNING2 indicator lights up or flashes if there is any trouble with your projector.

WARNING1 indicator

Flashing/Lighting indicators The number of

(Flashes in red)

Both indicators flash

(Flashes in red)

flashes

Three times The temperature of the light source is

Five times The top cover does not open properly.

Six times The unit detects a drop impact.

Seven times Turn the unit off, check if the speaker cords

Twice The internal temperature is unusually high.

Three times The fan is broken. Consult with qualified

WARNING2 indicator

Cause and Remedy

unusually high. Turn off the power and wait for the light source to cool, then turn on the power again. If the symptom persists, the light source may be at the end of its service life. In this case, consult with qualified Sony personnel.

Turn the unit off, then turn the unit on. If the top cover still does not open properly, consult with qualified Sony personnel.

If there is abnormality on the unit, consult with qualified Sony personnel. If there are no abnormalities on the unit, disconnect the AC power cord and check that the LED indicator turns off, then connect the AC power cord and turn the unit on.

are connected properly, then turn the unit on. If the indicators flashes seven times frequently, consult with qualified Sony personnel.

Check to ensure that if nothing is blocking the ventilation holes or whether or not the unit is being used at high altitudes.

Sony personnel.

Error Handling

About Indicators

Note

If the indicator starts flashing in a way of other than the above, and the symptom persists even after carrying out the above methods, consult with qualified Sony personnel.

About Indicators

Message Lists

Warning messages

Symptom Cause and Remedy Page

High temp.! Light off in 1 min.

Frequency is out of range!

Projector temperature is high. Cooling Setting should be “High” if projector is being used at high altitude.

Power Saving Mode is set. Projector will automatically enter Standby Mode in 1 minute.

Caution messages

Symptom Cause and Remedy Page

Not applicable! Press the appropriate button.

Turn off the power. – Check to ensure that nothing is blocking the ventilation

holes. Frequency is out of range. Input a signal that is within the

acceptable frequency range of the unit. Check to ensure that nothing is blocking the ventilation

holes. When using the unit at high altitude, set “Cooling Setting”

to “High.”

Note

When temperature inside the unit remains high, “Cooling Setting” is switched to “High” after 1 minute, then the fan speed increases.

“Power Saving” is set to “Standby.”

Note

If no signal is input, the power turns off after 1 minute, and the projector goes into standby mode.

No signal is input in the selected input. Check connections. 24

The operation to be activated by the button is currently prohibited.

–

Error Handling

Message Lists

Others

Updating the Software

You can download files to update the software of the unit. Copy the downloaded files to your USB memory, insert the USB memory to the USB terminal of the unit, then perform the update. To use the features updated, insert a USB memory device into a PC connected to the internet. Download the update files from the following Sony website: http://www.pro.sony.eu/pro/article/ projectors-home-cinema-article The website also explains how to install the update.

About x.v.Color

• “x.v.Color” is a promotion name given to the products that have the capability to realize a wide color space based on the xvYCC specifications and is a trademark of Sony Corporation.

• xvYCC is an international standard of the technical specifications of the extendedgamut color space for video signals. The color gamut of xvYCC is wider than the one of sRGB that is used with the current television system.

Updating the Software / About x.v.Color

About the Simulated

Cleaning

3D Feature

• Use the simulated 3D function taking into account that the picture will provide a different look from the original images, because this function converts the video images.

• Note that if the unit is used for profit or for public viewing, displaying 2D video images as 3D video images by converting to the simulated 3D may constitute an infringement of the rights of authors or producers, which are legally protected.

Cleaning the cabinet

• To remove dust from the cabinet, wipe gently with a soft cloth. If dust is persistent, wipe with a soft cloth slightly moistened with a diluted mild detergent solution.

• Never use any type of abrasive pad, alkaline/acid cleaner, scouring powder, or volatile solvent, such as alcohol, benzene, thinner or insecticide.

• Clean the unit with a cleaning cloth. Wiping with a dirty cloth may scratch the unit.

• Using such materials or maintaining prolonged contact with rubber or vinyl materials may result in damage to the cabinet material.

Cleaning the projection window

When removing dust from the projection window, open the top cover by holding both sides of the top cover with your hands and lifting it up.

Top cover

If the top cover is fully opened, it is locked. Clean the glass surface of the projection window with the top cover locked in the open position.

About the Simulated 3D Feature / Cleaning

Others

Glass surface of the projection window

After cleaning, close the top cover so that it returns to its original position.

Notes

• The projection window is made of glass. If you forcibly push or hit it, it may break and cause an injury.

• Your hands may be injured if caught when opening or closing the top cover.

Cleaning

Specifications

Item Description

Display System Projection system Display device SXRD 0.74-inch (18.8 mm) × 3

Number of pixels 4096 × 2160 × 3 pixels

Projection lens Zoom Powered (Approx. ×1.6)

Focus Powered Corner correction

adjustment Projection image size 66-inch to 147-inch (1,676 mm to 3,734 mm) Light source Laser diode Accepted digital signals See “Preset Signals” (page 64). Audio Power output 40 W + 40 W (at 8 Ω )

Supported format LPCM 2CH (up to 48 kHz) Inputs/Outputs

(Video/Audio/ Control)

Operating temperature (Operating humidity)

Storage temperature (Storage humidity) –20°C to +60°C (–4°F to +140°F) (10% to 90% (no

Power requirements AC 100 V to 240 V, 50/60 Hz Power consumption 520 W Standby mode

power consumption Dimensions (W×H×D) 1,100 mm × 265 mm × 535 mm (43.3 inches × 10.4

Mass Approx. 51.5 kg (113 lb 8.6 oz) Supplied accessories See “Checking the Supplied Accessories” (page 15). Optional accessories Active 3D Glasses: TDG-BT500A

HDMI Inputs 4

Speaker terminals 2

REMOTE RS-232C, D-sub 9-pin

LAN RJ45, 10BASE-T/100BASE-TX

IR IN Mini Jack

USB Type A, DC 5 V, Max. 500 mA

Powered

5°C to 35°C (41°F to 95°F) (35% to 85% (no condensation))

condensation))

0.5 W

inches × 21.1 inches)

Others

Notes

• The values for mass and dimensions are approximate.

• Not all optional accessories are available in all countries and area. Please check with your local Sony Authorized Dealer.

• Information on accessories in this manual is current as of May 2014.

Design and specifications of this unit and its optional accessories are subject to change without notice.

Specifications

Preset Signals

The following table shows the signals and video formats which you can project using this unit. When a signal other than the preset signals shown below is input, the picture may not be displayed properly.

Preset

memory no.

5 480/60p 480/60p

6 576/50p 576/50p

7 1080/60i 1080/60i

8 1080/50i 1080/50i

10 720/60p 720/60p

11 720/50p 720/50p

12 1080/60p 1080/60p

13 1080/50p 1080/50p

14 1080/24p 1080/24p

18 720/60p

19 720/50p

20 1080/24p

26 640 × 480 VESA 60 31.469 59.940 H-NEG, V-NEG 32 800 × 600 VESA 60 37.879 60.317 H-POS, V-POS 37 1024 × 768 VESA 60 48.363 60.004 H-NEG, V-NEG 45 1280 × 960 VESA 60 60.000 60.000 H-POS, V-POS 47 1280 × 1024 VESA 60 63.974 60.013 H-POS, V-POS 50 1400 × 1050 SXGA+ 65.317 59.978 H-NEG, V-POS 55 1280 × 768 1280 × 768/60 47.776 59.87 H-NEG, V-POS 71 1920 × 1080/60i

72 1920 × 1080/50i

74 3840 × 2160/60p* 3840×2160/60p

75 3840 × 2160/50p* 3840 × 2160/50p

76 4096 × 2160/60p* 4096 × 2160/60p

(Frame packing)

Preset signal (resolution) fH (kHz) fV (Hz) Sync

(Progressive NTSC) (720 × 480p)

(Progressive PAL) (720 × 576p)

(1920 × 1080i)

(1280 × 720p)

(1920 × 1080p)

(1920 × 1080p) 720/60p

(1280 × 720p) 720/50p

(1280 × 720p) 1080/24p

(1920 × 1080p)

1080/60i (1920 × 1080i)

1080/50i (1920 × 1080i)

(3840 × 2160)

(4096 × 2160)

31.470 60.000 –

31.250 50.000 –

33.750 60.000 –

28.130 50.000 –

45.000 60.000 –

37.500 50.000 –

67.500 60.000 –

56.260 50.000 –

26.973 23.976 –

90.000 60.000 –

75.000 50.000 –

53.946 23.976 –

67.500 60.000 –

56.250 50.000 –

135.000 60.000 –

112.500 50.000 –

135.000 60.000 –

Specifications

Preset

memory no.

77 4096 × 2160/50p* 4096 × 2160/50p

78 4096 × 2160/30p 4096 × 2160/30p

79 4096 × 2160/25p 4096 × 2160/25p

93 3840 × 2160/24p 3840 × 2160/24p

94 3840 × 2160/25p 3840 × 2160/25p

95 3840 × 2160/30p 3840 × 2160/30p

96 4096 × 2160/24p 4096×2160/24p

Preset signal (resolution) fH (kHz) fV (Hz) Sync

(4096 × 2160)

(3840 × 2160)

(4096 × 2160)

112.500 50.000 –

67.500 30.000 –

56.250 25.000 –

53.946 23.976 –

56.25 25 –

67.4325 29.97 –

54 24 –

* Available for YCbCr 4:2:0/8 bit.

Preset memory numbers for each input signal

Digital signal

Signal Preset memory number

Component signal (HDMI 1 to 4 connectors) 5 to 8, 10 to 14, 18 to 20, 71, 72, 74 to 79, 93 to

Video GBR signal (HDMI 1 to 4 connectors) 5 to 8, 10 to 14, 18 to 20, 71, 72, 78, 79, 93 to

Computer signal (HDMI 1 to 4 connectors) 10 to 13*, 26, 32, 37, 45, 47, 50, 55

* Some digital signals input from computers may be displayed as the preset memory number of

Component or Video GBR signal.

Specifications

Others

Input Signals and Adjustment/Setting Items

The items in the menus available to adjust differ depending on the input signal. The following tables indicate them. The items that cannot be adjusted/set are not displayed in the menu.

Picture menu

Item

Reality Creation Laser Light Setting

Component signal Video GBR signal Computer signal

zz–

zzz

Contrast Enhancer zz– Motionflow Contrast

zz–

zzz

Brightness zzz Color zz– Hue Color Temp.

zz–

zzz

Sharpness zz– NR

z (excluding preset

memory numbers 18

to 20, 71, 72, 74 to

79, and 93 to 96)

MPEG NR

z (excluding preset

memory numbers 18

to 20, 71, 72, 74 to

79, and 93 to 96)

Smooth Gradation

z (excluding preset

memory numbers 18

to 20, 71, and 72)

Film Mode

z (excluding preset

memory numbers 5,

6, 10 to 14, 18 to 20,

74 to 79, and 93 to

96)

Gamma Correction

zzz

Color Correction zzz Clear White zzz x.v.Color z –– Color Space

zzz

Input signal

z (excluding preset

memory numbers 18 to 20, 71, 72, 78, 79,

and 93 to 96)

z (excluding preset

memory numbers 18 to 20, 71, 72, 78, 79,

and 93 to 96)

z (excluding preset

memory numbers 18

to 20, 71, and 72)

z (excluding preset

memory numbers 5, 6, 10 to 14, 18 to 20, 78, 79, and 93 to 96)

–

z: Can be adjusted/set

–: Cannot be adjusted/set

Specifications

Screen menu

Item

Aspect*

z: Can be adjusted/set

Component signal Video GBR signal Computer signal

z (excluding preset

memory numbers 76

to 79 and 96)

Input signal

z (excluding preset

memory numbers 78,

79 and 96)

–

–: Cannot be adjusted/set *1: For further details, refer to the tables in “Aspect Mode” (page 69).

Note

When connecting a cable such as an HDMI cable, check the type of signal in the Information menu (page 51) and “Digital signal” (page 65), and check items that can be adjusted/set.

Compatible 3D Signals

This unit accepts the following types of 3D signals.

Resolution 3D signal format

720/60p, 720/50p Side-by-Side format

Over-Under format* Frame packing*

1080/60i, 1080/50i Side-by-Side format

Frame packing

1080/24P Side-by-Side format

Over-Under format* Frame packing*

1080/60p, 1080/50p Side-by-Side format

Over-Under format

*: Mandatory 3D format of the HDMI standards.

3D Signals and Adjustment/Setting Items

Some items on the menus may not be available to adjust/set, depending on the 3D signals. The items that cannot be adjusted are not displayed on the menu. The following tables indicate those items.

3D signals

Item

Reality Creation Laser Light Setting* Motionflow*

NR –––– MPEG NR –––– Smooth Gradation – – – –

720/60p,

720/50p

zzzz

1080/60i,

1080/50i

1080/24p 1080/60p,

1080/50p

Specifications

Others

3D signals

Item

Film Mode – x.v.Color

Aspect*

z: Can be adjusted/set

720/60p,

720/50p

zzzz

1080/60i,

1080/50i

z ––

1080/24p 1080/60p,

1080/50p

–: Cannot be adjusted/set *1: “Dynamic Control” cannot be selected. *2: The item is not available for Frame Packing/Over-Under/Side-by-Side on 720/60p, or Side-by-

Side on 1080/60p.

*3: For further details, refer to the tables in “Aspect Mode” (page 69).

When the unit is set to convert 2D video images to 3D video images, some items on the menus may be not available to adjust/set, depending on the “3D Format” settings on the Function menu. The items that cannot be adjusted are not displayed on the menu. The following tables indicate these items.

Item

Reality Creation Laser Light Setting* Motionflow*

Over-Under Side-by-Side Simulated 3D

zzz

3D signals

NR – – z MPEG NR – – z Smooth Gradation – – z Film Mode*

– zz

x.v.Color zzz

Aspect*

zzz

z: Can be adjusted/set

–: Cannot be adjusted/set *1: “Dynamic Control” cannot be selected. *2: The item is not available for Over-Under/Side-by-Side on 720/60p, or Side-by-Side on 1080/

60p. *3: The item is available only for 1080/60i or 1080/50i. *4: For further details, refer to the tables in “Aspect Mode” (page 69).

Specifications

Aspect Mode

Selectable items vary depending on the type of input signal or 3D format. For details, see the tables below. Items that cannot be selected are not displayed in the menu.

Acceptable signals 4096 × 2160 3840 × 2160

Preset memory number (page 64)

76 to 79, 96

74, 75, 93 to

1920 × 1080

1280 × 720

7, 8, 10 to 14 5, 6

1.85:1 Zoom – – zz –

2.35:1 Zoom – Normal

zzz – zzzz*

Stretch – – – z –

*1: Not displayed in the menu as fixed at Normal.

Acceptable signals 1920 × 1080, 1280 × 720

3D format Side-by-Side Over-Under Frame packing Simulated 3D

Preset memory number (page 64)

7, 8, 10 to 14 10 to 14 18 to 20, 71, 72 7, 8, 10 to 14

1.85:1 Zoom zzzz

2.35:1 Zoom zzzz Normal zzzz Stretch – – – –

720 × 480 720 × 576

Others

26, 32, 37, 45,

47, 50, 55

Storage Conditions of Adjustment/Setting Items

Each adjustment/setting item is individually stored for each input connector. For further details, see the tables below.

Preset memory numbers for each input signal

Input Preset memory numbers

HDMI 1 to 4 (2D) 5 to 8, 10 to 14, 26, 32, 37, 45, 47, 50, 55, 74 to 79, 93 to 96 HDMI 1 to 4 (3D) 7, 8, 10 to 14, 18 to 20, 71, 72

Specifications

Others

Picture menu

Item Storage conditions

Calib. Preset For each input connector Reset For each input connector and Calib. Preset Reality Creation Laser Light Setting Contrast Enhancer Motionflow Contrast Brightness Color Hue Color Temp. D93-D55 Custom 1-5 Gain R For each Color Temp., Custom 1-5 Gain G Gain B Bias R Bias G Bias B Sharpness For each input connector and Calib. Preset NR MPEG NR Smooth Gradation Film Mode Gamma Correction Color Correction Clear White x.v.Color Color Space

Screen menu

Item Storage conditions

Aspect For Picture Position 1.85:1, 2.35:1, or Custom 1-3

Specifications

Installation Distance and Projection Image Size

L1: Distance from a projection surface to the rear of the unit L2: Distance from a projection surface to the front of the unit D1: Maximum projection image size D2: Minimum projection image size H1: Distance from a floor to the bottom of a projection image (D1) H2: Distance from a floor to the bottom of a projection image (D2)

Installation Distance and Projection Image Size

Others

When projecting in 1.90:1 (Native Full Display 17:9) format

1.90

Projection image size Installation distance

Maximum projection

Intermediate

position

Shortest distance

installation

Diagonal 1

(D1)

147-inch (3.73 m)

127-inch (3.23 m)

106-inch (2.69 m)

Maximum Minimum

Width ×

Height

3.30 m ×

1.74 m

(130 inches

× 69 inches)

2.84 m ×

1.50 m

(112 inches

× 59 inches)

2.39 m ×

1.26 m

(94 inches ×

50 inches)

Bottom height

(H1)

45 cm

(18

inches)

41 cm

(16

inches)

38 cm

(15

inches)

Diagonal 2

(D2)

92-inch

(2.34 m)

79-inch

(2.03 m)

66-inch

(1.68 m)

Width ×

Height

2.07 m ×

1.09 m

(81 inches ×

43 inches)

1.78 m ×

0.94 m

(70 inches ×

37 inches)

1.49 m ×

0.79 m

(59 inches ×

31 inches)

Bottom

height

(H2)

57 cm

(22

inches)

51 cm

(20

inches)

46 cm

(18

inches)

From a

projecting

surface to the rear of the unit L1

17 cm

(6.7 inches)

8.5 cm

(3.3 inches)

0 cm

(0 inch)

From a projecting surface to

the front of the unit L2

70.5 cm

inches)

62.0 cm

inches)

53.5 cm

inches)

Formula 1 (calculates a installation distance from a projection image size)

Unit: cm (inches)

Maximum projection image size Minimum projection image size

L1 = 0.1857 × W1 – 44.3090 (L1 = 0.1857 × W1 – 17.4445)

L2 = 0.1857 × W1 + 9.1910 (L2 = 0.1857 × W1 + 3.6185)

L1 = 0.2964 × W2 – 44.2027 (L1 = 0.2964 × W2 – 17.4026)

L2 = 0.2964 × W2 + 9.2973 (L2 = 0.2964 × W2 + 3.6604)

(27.8

(24.4

(21.0

Formula 2 (calculates a projection image size from a installation distance)

Unit: cm (inches)

From a projecting surface to the rear of the unit

W1 = 5.3850 × L1 + 238.6044 (W1 = 5.3850 × L1 + 93.9388)

W2 = 3.3734 × L1 + 149.1119 (W2 = 3.3734 × L1 + 58.7055)

From a projecting surface to the front of the unit

W1 = 5.3850 × L2 – 49.4932 (W1 = 5.3850 × L2 – 19.4855)

W2 = 3.3734 × L2 – 31.3627 (W2 = 3.3734 × L2 – 12.3475)

Formula 3 (calculates a distance from a floor to the bottom of a projection image)

Unit: cm (inches)

Maximum projection image size Minimum projection image size

H1 = 0.0798 × W1 + 18.6804 (H1 = 0.0798 × W1 + 7.3545)

Installation Distance and Projection Image Size

H2 = 0.1830 × W2 + 18.8798 (H2 = 0.1830 × W2 + 7.4330)

When projecting in 1.78:1 (16:9) format

1.78

Video display area

Projection area

Projection image size Installation distance

Maximum Minimum

Width ×

Height

3.10 m ×

1.74 m

(122 inches

× 69 inches)

2.67 m ×

1.50 m

(105 inches

× 59 inches)

2.24 m ×

1.26 m

(88 inches ×

50 inches)

Bottom

height (H1)

45 cm

(18

inches)

41 cm

(16

inches)

38 cm

(15

inches)

Diagonal 2

(D2)

88-inch

(2.24 m)

75-inch

(1.91 m)

63-inch

(1.60 m)

Width ×

Height

1.94 m ×

1.09 m

(76 inches ×

43 inches)

1.67 m×

0.94 m

(66 inches ×

37 inches)

1.40 m ×

0.79 m

(55 inches ×

31 inches)

Bottom

height

(H2)

57 cm

(22

inches)

51 cm

(20

inches)

46 cm

(18

inches)

From a projecting surface to

the rear of the unit L1

17 cm

(6.7 inches)

8.5 cm

(3.3 inches)

0 cm

(0 inch)

From a projecting surface to

the front of the unit L2

70.5 cm

inches)

62.0 cm

inches)

53.5 cm

inches)

Maximum projection

Intermediate

position

Shortest distance

installation

Diagonal 1

(D1)

140-inch (3.56 m)

120-inch (3.05 m)

101-inch (2.57 m)

Formula 1 (calculates a installation distance from a projection image size)

Unit: cm (inches)

Maximum projection image size Minimum projection image size

L1 = 0.1980 × W1 – 44.3078 (L1 = 0.1980 × W1 – 17.444)

L2 = 0.1980 × W1 + 9.1922 (L2 = 0.1980 × W1 + 3.6190)

L1 = 0.3163 × W2 – 44.2027 (L1 = 0.3163 × W2 – 17.4097)

L2 = 0.3163 × W2 + 9.2793 (L2 = 0.3163 × W2 + 3.6533)

(27.8

(24.4

(21.0

Formula 2 (calculates a projection image size from a installation distance)

Unit: cm (inches)

From a projecting surface to the rear of the unit

W1 = 5.0502 × L1 + 223.7640 (W1 = 5.0502 × L1 + 88.0961)

W2 = 3.1620 × L1 + 139.8246 (W2 = 3.1620 × L1 + 55.0490)

From a projecting surface to the front of the unit

W1 = 5.0502 × L2 – 46.4218 (W1 = 5.0502 × L2 – 18.2763)

W2 = 3.1620 × L2 – 29.3402 (W2 = 3.1620 × L2 – 11.5513)

Formula 3 (calculates a distance from a floor to the bottom of a projection image)

Unit: cm (inches)

Maximum projection image size Minimum projection image size

H1 = 0.0851 × W1 + 18.6809 (H1 = 0.0851 × W1 + 7.3547)

H2 = 0.1953 × W2 + 18.8687 (H2 = 0.1953 × W2 + 7.4286)

Installation Distance and Projection Image Size

Others

Dimensions

Front

Top

1100 (43 3/8)

Unit: mm (inches)

)

265 (10

Unit: mm (inches)

)

535 (21

Dimensions

Location of the label

Warning label

Explanation label

Laser emission port

Laser Diode Properties

3.5 W, 28 Laser diodes (440 to 455 nm)

2.4 W, 7 Laser diodes (455 to 470 nm)

Beam divergence angle from the projection window of this unit

Wide: α = 144° Tele: α = 123°

Laser emission port

Dimensions

Others

NOTICES AND LICENCES FOR SOFTWARE USED IN THIS PRODUCT

GPL/LGPL LICENSED SOFTWARE

The following GPL executables and LGPL libraries are used in this product and are subject to the GPL/ LGPL License Agreements included as part of this documentation:

Package list:

linux-kernel alsa-lib busybox crypto directfb dosfstools e2fsprogs exceptionmonitor fuse gdisk glib glibc iptables libmicrohttpd libnuma (in numactl) procps pump-autoip XZ utils Source code for these executables and libraries, as well as other executables and libraries, can be obtained using the following link: http://oss.sony.net/Products/Linux/ ===============================

GNU GENERAL PUBLIC LICENSE Version 2, June 1991

Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA. Everyone is permitted t o copy and distribute verbatim copies of this license document, but changing it is not allowed.

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of

the Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Library General Public License instead.) You can apply it to your programs, too. When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things. To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it. For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights. We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software. Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors’ reputations. Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all. The precise terms and conditions for copying, distribution and modification follow.

GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

0. This License applies to any program or other work

which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter,

NOTICES AND LICENCES FOR SOFTWARE USED IN THIS PRODUCT

translation is included without limitation in the term “modification”.) Each licensee is addressed as “you”. Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents consti tute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.

1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change. b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License. c) If the modified program normally reads com mands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropria te copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permission s for other

licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program. In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.

3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following: a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, b) Accompany it wit h a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete m achine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, c) Accompany it with the information yo u received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.) The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.

4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will

Others

NOTICES AND LICENCES FOR SOFTWARE USED IN THIS PRODUCT

automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distri bute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.

6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License.

7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or i ndirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous cont ributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a conse quence of the rest of this License.

8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation.

10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER,

NOTICES AND LICENCES FOR SOFTWARE USED IN THIS PRODUCT

OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Programs

If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the “copyright” line and a pointer to where the full notice is found. <one line to give the program’s name and a brief idea of what it does.> Copyright (C) <year> <name of author> This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA. Also add information on how to contact you by electronic and paper mail. If the program is interactive, make it output a short notice like this when it starts in an interactive mode: Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type ‘show w’. This is free software, and you are welcome to redistribute it under certain conditions; type ‘show c’ for details. The hypothetical commands ‘show w’ and ‘show c’ should show the appropriate parts of the General

Public License. Of course, the commands you use may be called something other than ‘show w’ and ‘show c’; they could even be mouse-clicks or menu items--whatever suits your program. You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the program, if necessary. Here is a sample; alter the names: Yoyodyne, Inc., hereby disclaims all copyright interest in the program ‘Gnomovision’ (which makes passes at compilers) written by James Hacker. <signature of Ty Coon>, 1 April 1989 Ty Coon, President of Vice This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Library General Public License instead of this License. ===============================

GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999

Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA. Everyone is permitted to copy an d distribute verbatim copies of this license document, but changing it is not allowed. [This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number

2.1.]

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software-to make sure the software is free for all its users. This license, the Lesser General Public License, applies to some specially designated software packagestypically libraries--of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you first think carefully about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below. When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free

Others

NOTICES AND LICENCES FOR SOFTWARE USED IN THIS PRODUCT

programs; and that you are informed that you can do these things. To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it. For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights. We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/or modify the library. To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modified by someone else and passed on, the recipients should know that what they have is not the original version, so that the original author’s reputation will not be affected by problems that might be introduced by others. Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specified in this license. Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General Public License, appl ies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to permit linking those libraries into non-free programs. When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library. We call this license the “Lesser” General Public License because it does Less to protect the user’s freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries.

However, the Lesser license provides advantages in certain special circumstances. For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License. In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system. Although the Lesser General Public License is Less protective of the users’ freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library. The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a “work based on the library” and a “work that uses the library”. The former contains code derived from the library, whereas the latter must be combined with the library in order to run.

GNU LESSER GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

0. This License Agreement applies to any software

library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called “this License”). Each licensee is addressed as “you”. A “library” means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables. The “Library”, below, refers to any such software library or work which has been distributed under these terms. A “work based on the Library” means either the Library or any derivative work under copyright law: that is to say, a work containing the Library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term “modification”.) “Source code” for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface

NOTICES AND LICENCES FOR SOFTWARE USED IN THIS PRODUCT

definition files, plus the scripts used to control compilation and installation of the library. Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does.

1. You may copy and distribute verbatim copies of the Library’s complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

2. You may modify your copy or copies of th e Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) The modified work must itself be a software library. b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change. c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License. d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful. (For example, a function in a library to compute square roots has a purpose that is entirely welldefined independent of the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Library, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on

the Library, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Library. In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.

3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead i f you wish.) Do not make any other change in these notices. Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy. This option is useful when you wish to copy part of the code of the Library into a program that is not a library.

4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange. If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code.

5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a “work that uses the Library”. Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License. However, linking a “work that uses the Library” with the Library creates an executable that is a derivative of the Library (because it contains portions of the Library), rather than a “work that uses the library”. The executable is therefore covered by this License. Section 6 states terms for distribution of such executables.

Others

NOTICES AND LICENCES FOR SOFTWARE USED IN THIS PRODUCT

When a “work that uses the Library” uses material from a header file that is part of the Library, the object code for the work may be a derivative work of the Library even though the source code is not. Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law. If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.) Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself.

6. As an exception to the Sections above, you may also combine or link a “work that uses the Library” with the Library to produce a work containing portions of the Library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customer’s own use and reverse engineering for debugging such modifications. You must give prominent no tice with each copy of the work that the Library is used in it and that the Library and its use are covered by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this License. Also, you must do one of these things: a) Accompany the work with the complete corresponding machine-readable source code for the Library including whatever changes were used in the work (which must be dist ributed under Secti ons 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable “work that uses the Library”, as object code and/or source code, so that the user can modify the Library and then relink to produce a modified executable containing the modified Libra ry. (It is understood that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions.) b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at run time a copy of the library already present on the user’s computer system, rather than copying library functions into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified

version is interface-compatible with the version that the work was made with. c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution. d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place. e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy. For an executable, the required form of the “work that uses the Library” must include any data and utility programs needed for repr oducing the executable from it. However, as a special exception , the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction mea ns you cannot use both them and the Library together in an executable that you distribute.

7. You may place library facilities that are a work based on the Library side-by-side in a single library together with other library facilities not covered by this License, and distribute such a combined library, provided that the separate distribution of the work based on the Library and of the other library facilities is otherwise permitted, and provided tha t you do these two things: a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This must be distributed under the terms of the Sections above. b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining where to find the accompanying uncombined form of the same work.

8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will a utomatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by

NOTICES AND LICENCES FOR SOFTWARE USED IN THIS PRODUCT

modifying or distributing the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it.

10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this License.

11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty-free redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Library. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a co nsequence of the rest of this License.

12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Library specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Fre e Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free Software Foundation.

14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we some times make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

15. BECAUSE THE LIBRARY IS LICENSED

FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/ OR OTHER PARTIES PROVIDE THE LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE

Others

NOTICES AND LICENCES FOR SOFTWARE USED IN THIS PRODUCT

LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Libraries

If you develop a new library, and you want it to be of the greatest possible us e to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License). To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the “copyright” line and a pointer to where the full notice is found. <one line to give the library’s name and a brief idea of what it does.> Copyright (C) <year> <name of author> This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public license as published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version. This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details. You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 021101301, USA. Also add information on how to contact you by electronic and paper mail. You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the library, if necessary. Here is a sample; alter the names: Yoyodyne, Inc., hereby disclaims all copyright interest in the library ‘Frob’ (a library for tweaking knobs) written by James Random Hacker. <signature of Ty Coon>, 1 April 1990 Ty Coon, President of Vice ===============================

Notification of BSD

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following acknowledgement:

4. Neither the name of the following developers nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. The following notices are required to satisfy the license terms of the software that we have mentioned in this document: This product includes software developed by the NetBSD Foundation, Inc. and its contributors. This product includes software developed by the University of California, Berkeley and its contributors. This product includes software developed for the NetBSD Project. See http://www.NetBSD.org/ for information about NetBSD. This product includes software developed by Christos Zoulas. This product includes software developed by Niels Provos. This product includes software developed by the University of California, Lawrence Berkeley Laboratory. This product includes software developed by WIDE Project and its contributors. This product includes software developed by Brian Aker.

NOTICES AND LICENCES FOR SOFTWARE USED IN THIS PRODUCT

This product includes software developed by Danga Interactive, Inc. ===============================

INDEPENDENT JPEG GROUP SOFTWARE

This software is based in part on the work of the Independent JPEG Group. ===============================

SOFTWARE DEVELOPED BY THE OPENSSL PROJECT FOR USE IN THE SSL TOOLKIT

Copyright (c) 1998-2008 The OpenSSL Project. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

3. All advertising materials mentioning features or use of this software must display the following acknowledgment: “This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (<http://www.openssl.org/>)”

4. The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact openssl-core@openssl.org.

5. Products derived from this software may not be called “OpenSSL” nor may “OpenSSL” appear in their names without prior written permission of the OpenSSL Project.

6. Redistributions of any form whats oever must retain the following acknowledgment: “This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (<http:// www.openssl.org/>)” THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS’’ AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR

PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. This product includes cryptographic software written by Eric Young (eay@cryptsoft.com). This product includes software written by Tim Hudson (tjh@cryptsoft.com). Original SSLeay License

---------------------Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com) All rights reserved. This package is an SSL implementation written by Eric Young (eay@cryptsoft.com). The implementation was written so as to conform with Netscapes SSL. This library is free for commercial and noncommercial use as long as the following conditions are adhered to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DE S, etc., code; not just the SSL code. The SSL documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson (tjh@cryptsoft.com). Copyright remains Eric Young’s, and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric Young should be given attribution as the author of the parts of the library us ed. This can be in the form of a t extual message at program startup or in documentation (online or textual) provided with the package. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.

3. All advertising materials mentioning features or use of this software must display the following acknowledgement: “This product includes cryptographic software written by Eric Young (eay@cryptsoft.com)”. The word ‘cryptographic’ can be left out if the routines from the library being used are not cryptographic related:-).

4. If you include any Windows specific code (or a derivative thereof) from the apps directory (application code) you must include an acknowledgement: “This product includes software written by Tim Hudson (tjh@cryptsoft.com)”.

Others

NOTICES AND LICENCES FOR SOFTWARE USED IN THIS PRODUCT

THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS’’ AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. The license and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution license [including the GNU Public License.] ===============================

FREETYPE/FREETYPE2 SOFTWARE

The software is based in part of the work of the FreeType Team. ===============================

Notification of MIT

EXPAT Copyright (c) 1998, 1999, 2000 Thai Open Source Software Center Ltd and Clark Cooper Copyright (c) 2001, 2002, 2003, 2004, 2005, 2006 Expat maintainers. JSONcpp Copyright (c) 2007-2010 Baptiste Lepilleur yaml-cpp Copyright (c) 2008 Jesse Beder. cJSON Copyright (c) 2009 Dave Gamble GIFLIB Copyright (c) 1997 Eric S. Raymond PyYAML Copyright (c) 2006 Kirill Simonov Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions: The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. ===============================

CURL SOFTWARE

COPYRIGHT AND PERMISSION NOTICE. Copyright (c) 1996 - 2012, Daniel Stenberg, <daniel@haxx.se>. All rights reserved. Permission to use, copy, modify, and distribute this software for any purpose with or without fee is hereby granted, provided that the above copyright notice and this permission notice appear in all copies. THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF THIRD PARTY RIGHTS. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. Except as contained in this notice, the name of a copyright holder shall not be used in advertising or otherwise to promote the sale, use or other dealings in this Software without prior written authorization of the copyright holder. ===============================

klibc and jemalloc

All of the documentation a nd software included in the

4.4BSD and 4.4BSD-Lite Releases is copyrighted by The Regents of the University of California. Copyright 1979, 1980, 1983, 1986, 1988, 198 9, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

NOTICES AND LICENCES FOR SOFTWARE USED IN THIS PRODUCT

Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

All advertising materials mentioning features or use of this software must display the following acknowledgement:

This product includes software developed by the University of California, Berkeley and its contributors. Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS “AS IS’’ AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. The Institute of Electrical and Electronics Engineers and the American National Standards Committee X3, on Information Processing Systems have given us permission to reprint portions of their documentation. In the following statement, the phrase “this text’’ refers to portions of the system documentation. Portions of this text are reprinted and reproduced in electronic form in the second BSD Networking Software Release, from IEEE Std 1003.1-1988, IEEE Standard Portable Operating System Interface for Computer Environments (POSIX), copyright C 1988 by the Institute of Electrical and Electronics Engineers, Inc. In the event of any discrepancy between these versions and the original IEEE Standard, the original IEEE Standard is the referee document. In the following statement, the phrase “This material’’ refers to portions of the system documentation.

This material is reproduced with permission from American National Standards Committee X3, on Information Processing Systems. Computer and Business Equipment Manufacturers Association (CBEMA), 311 First St., NW, Suite 500, Washington, DC 20001-2178. The developmental work of Programming Language C was completed by the X3J11 Technical Committee. The views and conclusions contained in the software and documentation are those of the authors and should not be interpreted as representing official policies, either expressed or implied, of the Regents of the University of California. ===============================

Big5 Font(DynaComware)

The DynaFont used on the screen display are solely develop by DynaComware. ===============================

icu(libic)

ICU License - ICU 1.8.1 and later COPYRIGHT AND PERMISSION NOTICE Copyright (c) 1995-2012 International Business Machines Corporation and others All rights reserved. Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, provided that the above copyright notice(s) and this permission notice appear in all copies of the Software and that both the above copyright notice(s) and this permission notice appear in supporting documentation. THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF THIRD PARTY RIGHTS. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR HOLDERS INCLUDED IN THIS NOTICE BE LIABLE FOR ANY CLAIM, OR ANY SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES, OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.

Others

NOTICES AND LICENCES FOR SOFTWARE USED IN THIS PRODUCT

Except as contained in this notice, the name of a copyright holder shall not be used in advertising or otherwise to promote the sale, use or other dealings in this Software without prior written authorization of the copyright holder.

-------------------------------------------All trademarks and registered trademarks mentioned herein are the property of their respective owners. ===============================

dhcpd

Copyright (c) 2004-2011 by Internet Systems Consortium, Inc. (“ISC”) Copyright (c) 1995-2003 by Internet Software Consortium Permission to use, copy, modify, and distribute this software for any purpose with or witho ut fee is hereby granted, provided that the above copyright notice and this permission notice appear in all copies. THE SOFTWARE IS PROVIDED “AS IS” AND ISC DISCLAIMS ALL WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL ISC BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. Internet Systems Consortium, Inc. 950 Charter Street Redwood City, CA 94063 info@isc.org https://www.isc.org/ ===============================

libevent

Libevent is available for use under the following license, commonly known as the 3-clause (or “modified”) BSD license: ============== Copyright (c) 2000-2007 Niels Provos <provos@citi.umich.edu> Copyright (c) 2007-2010 Niels Provos and Nick Mathewson Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the

following disclaimer in the documentation and/or other materials provided with the distribution.

3. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE AUTHOR “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ============== Portions of Libevent are based on works by others, also made available by them under the three-clause BSD license above. The copyright notices are available in the corresponding sour ce files; the license is as above. Here’s a list: log.c: Copyright (c) 2000 Dug Song <dugsong@monkey.org> Copyright (c) 1993 The Regents of the University of California. strlcpy.c: Copyright (c) 1998 Todd C. Miller <Todd.Miller@courtesan.com> win32select.c: Copyright (c) 2003 Michael A. Davis <mike@datanerds.net> evport.c: Copyright (c) 2007 Sun Microsystems ht-internal.h: Copyright (c) 2002 Christopher Clark minheap-internal.h: Copyright (c) 2006 Maxim Yegorushkin <maxim.yegorushkin@gmail.com> ============== The arc4module is available under the following, sometimes called the “OpenBSD” license: Copyright (c) 1996, David Mazieres <dm@uun.org> Copyright (c) 2008, Damien Miller <djm@openbsd.org> Permission to use, copy, modify, and distribute this software for any purpose with or without fee is hereby

NOTICES AND LICENCES FOR SOFTWARE USED IN THIS PRODUCT

granted, provided that the above copyright notice and this permission notice appear in all copies. THE SOFTWARE IS PROVIDED “AS IS” AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. ===============================

boost

Boost Software License - Version 1.0 - August 17th, 2003 Permission is hereby granted, free of charge, to any person or organization obtaining a copy of the software and accompanying documentation covered by this license (the “Software”) to use, reproduce, display, distribute, execute, and transmit the Software, and to prepare derivative works of the Software, and to permit third-parties to whom the Software is furnished to do so, all subject to the following: The copyright notices in the Software and this entire statement, including the above license grant, this restriction and the following disclaimer, must be included in all copies of the Software, in whole or in part, and all derivative works of the Software, unless such copies or derivative works are solely in the form of machine-executable object code generated by a source language processor. THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE AND NONINFRINGEMENT. IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR ANYONE DISTRIBUTING THE SOFTWARE BE LIABLE FOR ANY DAMAGES OR OTHER LIABILITY, WHETHER IN CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. ===============================

ppp

Copyrights: ***********

All of the code can be freely used and redistributed. The individual source files each have their own copyright and permission notice. Pppd, pppstats and pppdump are under BSD-style notices. Some of the pppd plugins are GPL’d. Chat is public domain. ===============================

ntp

Copyright (c) University of Delaware 1992-2012. Permission to use, copy, modify, and distribute this software and its documentation for any purpose with or without fee is hereby granted, provided that the above copyright notice appears in all copies and that both the copyright notice and this permission notice appear in supporting documentation, and that the name University of Delaware not be used in advertising or publicity pertaining to distribution of the software without specific, written prior permission. The University of Delaware makes no representations about the suitability this software for any purpose. It is provided “as is” without express or implied warranty. ===============================

libcap

Unless otherwise *explicitly* stated, the following text describes the licensed condit ions under which the contents of this libcap release may be used and distributed: Redistribution and use in source and binary forms of libcap, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain any existing copyright notice, and this entire permission notice in its entirety, including the disclaimer of warranties.

2. Redistributions in binary form must reproduce all prior and current copyright notices, this list of conditions, and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. The name of any author m ay not be used to e ndorse or promote products derived from this software without their specific prior written permission. ALTERNATIVELY, this product may be distributed under the terms of the GNU General Public License, in which case the provisions of the GNU GPL are required INSTEAD OF the above restrictions. (This clause is necessar y due to a potential conflict betwe en the GNU GPL and the restrictions contained in a BSD-style copyright.) THIS SOFTWARE IS PROVIDED “AS IS’’ AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN

Others

NOTICES AND LICENCES FOR SOFTWARE USED IN THIS PRODUCT

NO EVENT SHALL THE AUTHOR(S) BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ===============================

Python®

Python® is a registered trademark of the Python Software Foundation. ===============================

lighttpd

Copyright (c) 2004, Jan Kneschke, incremental All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: – Redistributions of source code must retain the

above copyright notice, this list of conditions and the following disclaimer.

– Redistributions in binary form must reproduce the

above copyright notice, this list of conditions and the following disclaimer in the documentation and/ or other materials provided with the distribution.

– Neither the name of the ‘incremental’ nor the

names of its contributors may be used to endorse or promote products derived from this software

without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS

SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ===============================

pcre

PCRE LICENCE

-----------PCRE is a library of functions to support regular expressions whose syntax and semantics are as close as possible to those of the Perl 5 language. Release 8 of PCRE is distributed under the terms of the “BSD” licence, as specified below. The documentation for PCRE, supplied in the “doc” directory, is distributed under the same terms as the software itself. The basic library functions are written in C and are freestanding. Also included in the distribution is a set of C++ wrapper functions.

THE BASIC LIBRARY FUNCTIONS

--------------------------Written by: Philip Hazel Email local part: ph10 Email domain: cam.ac.uk University of Cambridge Computing Service, Cambridge, England. Copyright (c) 1997-2010 University of Cambridge All rights reserved.

THE C++ WRAPPER FUNCTIONS

THE “BSD” LICENCE

----------------Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: * Redistributions of source code must retain the

above copyright notice, this list of conditions and the following disclaimer.

* Redistributions in binary form must reproduce the

above copyright notice, this list of conditions and the following disc laimer in the documentatio n and/ or other materials provided with the distribution.

* Neither the name of the University of Cambridge

nor the name of Google Inc. nor the names of their contributors may be used to endorse or promote products derived from this software without

specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

NOTICES AND LICENCES FOR SOFTWARE USED IN THIS PRODUCT

PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. End

NOTICES AND LICENCES FOR SOFTWARE USED IN THIS PRODUCT

Others

Index

Numerics

3D glasses

3D glasses communication range ........29

Using the 3D glasses ........................... 29

3D Settings

2D-3D Display Sel. (Select) ................46

3D Brightness ......................................47

3D Depth Adjust ................................. 47

3D Format ...........................................46

Simulated 3D Effect ............................ 47

3D video ..................................................29

Aspect

1.85:1 Zoom .................................. 31, 43

2.35:1 Zoom .................................. 31, 43

Normal ........................................... 32, 43

Stretch ........................................... 32, 43

Auto Calibration ......................................41

Blanking .................................................. 48

Brightness ............................................... 38

Calib. Preset

Bright Cinema ..................................... 36

Bright TV ............................................36

Cinema Film 1 .....................................36

Cinema Film 2 .....................................36

Game ................................................... 36

Photo ...................................................36

Reference ............................................. 36

TV .......................................................36

User ..................................................... 36

Cinema Black Pro ...................................37

Cleaning .................................................. 61

Clear White .............................................40

Color .......................................................38

Color Correction ..................................... 40

Color Space .............................................40

Color Temp. (Temperature) .....................38

Compatible 3D signals ............................67

Connecting speakers ...............................26

Connecting to Video equipment or a

computer .......................................... 24

Connectors ........................................ 11, 13

Contrast ....................................................38

Contrast Enhancer ...................................37

Control panel ...........................................11

Cooling Setting ........................................44

Dimensions ..............................................74

Dynamic Range .......................................47

Expert Setting ..........................................39

Film Mode ...............................................39

Gamma Correction ..................................39

Hue ..........................................................38

Illumination .............................................48

Input Lag Reduction ................................40

Input signals and adjustable/setting

items ................................................66

Installation distance and projection image

size ...................................................71

LAN connector ..................................13, 52

Language .................................................44

Laser Light Setting ..................................37

LENS ADJUSTMENT

CORNER CORRECTION ...................19

FOCUS ................................................19

ZOOM ..................................................19

Lens Control ............................................48

Location of controls

Front .....................................................11

Rear/Bottom .........................................13

Advanced Picture .................................41

Function ...............................................46

Information ..........................................51

Installation ...........................................48

Operation .............................................34

Index

Picture ..................................................36

Screen ..................................................42

Setup ....................................................44

Menu Position .........................................44

Messages

Caution ................................................59

Warning ...............................................59

Motionflow ..............................................38

MPEG NR (MPEG Noise Reduction) .....39

Network Features ....................................52

Network Management .............................45

Network Setting .......................................50

NR (Noise Reduction) .............................39

Panel Alignment ......................................49

Picture Position

Picture Position ....................................42

Using the Picture Position ...................30

Picture position adjustment .....................17

Picture Viewing Mode .............................33

Power Saving ...........................................45

Preset memory .........................................51

Preset mode

BRT CINE ...........................................33

BRT TV ...............................................33

CINEMA FILM 1 ................................33

CINEMA FILM 2 ................................33

GAME .................................................33

PHOTO ................................................33

REF ......................................................33

TV ........................................................33

USER ...................................................33

Preset signals ...........................................64

Projecting the Picture ..............................28

Reality Creation .......................................37

Remote control

Inserting the batteries ..........................15

Location of buttons ..............................14

Remote control detector ..........................11

Remote Start ............................................44

Reset ........................................................37

Resetting the items ..................................35

Sharpness .................................................38

Signal type ...............................................51

Simulated 3D feature ..............................61

Smooth Gradation ................................... 39

Software Version ..................................... 51

Speaker .................................................... 47

Specifications .......................................... 63

Status ....................................................... 44

Supplied accessories ...............................15

Test pattern .............................................. 18

Troubleshooting ...................................... 54

Turning off .............................................. 28

Turning on ............................................... 18

Updating the software ............................. 60

V Keystone .............................................. 48

Volume .................................................... 47

WARNING indicator .............................. 57

x.v.Color ............................................ 40, 60

Trademark Information

• “PlayStation” is a registered trademark of Sony Computer Entertainment Inc.

• This unit incorporates High-Definition Multimedia Interface (HDMI technology. The terms HDMI and HDMI HighDefinition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

• “Blu-ray” and “Blu-ray Disc” are trademarks of Blu-ray Disc Association.

........................................................................

This projector supports DeepColor, x.v.Color, LipSync, computer input signal, 3D signal and 4K signal of HDMI standards. It also supports HDCP.

)

Others

Index

Sony LSPX-W1S Operating Instructions

Specifications and Main Features

Frequently Asked Questions

User Manual

WARNING

Table of Contents

Precautions

Notes on Installation and Usage

Carrying the unit

Unsuitable installation

Unsuitable Conditions

Location of Controls

Front

Rear/Bottom

Remote Control

Connections and Preparations

Checking the Supplied Accessories

Inserting the Batteries into the Remote Control

Connecting the AC Power Cord

Installing the Unit

Attaching the Bottom Covers

Attaching the Terminal Door

Connecting to Video Equipment or a Computer

Connecting the Exclusive Speakers

Selecting the Menu Language

Projecting

Projecting the Picture

Turning Off the Power

Watching 3D Video Images

Using the 3D Glasses

Using the Picture Position

Selecting the Aspect Ratio According to the Video Signal

Selecting the Picture Viewing Mode

Using the Menus

Operation through the Menus

Picture Menu

Advanced Picture Menu

Screen Menu

Setup Menu

Function Menu

Installation Menu

Information Menu

About the Preset Memory

Using Network Features

Displaying the Control Window of the Unit with a Web Browser

Operating the Control Window

Switching the Page

Setting the Access Limitation

Confirming the Information Regarding the Unit

Error Handling

Troubleshooting

About Indicators

Message Lists

Others

Updating the Software

About x.v.Color

Cleaning

Specifications

Preset Signals

Input Signals and Adjustment/Setting Items

Compatible 3D Signals

3D Signals and Adjustment/Setting Items

Aspect Mode

Storage Conditions of Adjustment/Setting Items

Installation Distance and Projection Image Size

Dimensions

NOTICES AND LICENCES FOR SOFTWARE USED IN THIS PRODUCT

Index