Sony KV-XA29M60, KV-XA29M84 R Service Manual

MODEL COMMANDER DEST. CHASSIS NO.

CHASSIS

TRINITRON

COLOR TV

SERVICE MANUAL

BG-3R

MODEL COMMANDER DEST. CHASSIS NO.

KV-XA29M60 RM-954 Thailand SCC-U49B-A KV-XA29M84 RM-953 ME SCC-U48A-A

-/--

FAVORITE

SOUND MODE

PIC MODE

ENTER

A/B

SURROUND

RM-954

-/--

FAVORITE

SOUND MODE

SURROUND

PIP PROGR

ENTER

PIC MODE

RM-953

– 2 –

KV-XA29M60/XA29M84

RM-954 RM-953

SPECIFICATIONS

Note

Power requirements 110-240 V AC, 50/60 Hz KV-XA29M84 only

220-240 V AC, 50/60 Hz KV-XA29M60 only

Power consumption (W) Indicated on the rear of the TV

Television system B/G, I, D/K, M

Color system PAL, PAL 60, SECAM, NTSC4.43, NTSC3.58

Stereo/Bilingual system NICAM Stereo/Bilingual B/G, I, DK; A2 Stereo/Bilingual B/G KV-XA29M60 only

Channel coverage

B/G VHF: E2 to E12 / UHF: E21 to E69 / CATV: S01 to S03, S1 to S41

I UHF: B21 to B68 / CATV: S01 to S03, S1 to S41

D/K VHF: C1 to C12, R1 to R12 / UHF: C13 to C57, R21 to R60

CATV: S01 to S03, S1 to S41, Z1 to Z39

M VHF: A2 to A13 / UHF: A14 to A79 /

CATV: A-8 to A-2, A to W+4, W+6 to W+84

˘ (Antenna) 75-ohm external terminal

Audio output (Speaker) 8W + 8W 10% distortion

Number of terminal

D (Video) Input: 4* Output: 1 * Three input lines available Phono jacks; 1 VP-P, 75 ohms ≥ (Audio) Input: 4* Output: 1 * Three input lines available Phono jacks; 500 mVrms

(S Video) Input: 2 Y : 1 Vp-p, 75 ohms,

unbalanced, sync negative

C : 0.286 Vp-p, 75 ohms

(Component Video)

Input: 1 Phono jacks

Y : 1 Vp-p, 75 ohms, sync negative C

B : 0.7 Vp-p, 75 ohms

R : 0.7 Vp-p, 75 ohms

Audio : 500 mVrms

2 (Headphones) Output: 1 Stereo minijack

Picture tube 29 inch

Tube size (cm) 72 Measured diagonally

Screen size (cm) 68 Measured diagonally

Dimension (w/h/d, mm) 722 x 576 x 516

Mass (kg) 51

Design and specifications are subject to change without notice.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY SHADING AND MARK ! ON THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

CAUTION

SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR CARBON PAINTED ON THE CRT, AFTER REMOVING THE ANODE.

– 3 –

KV-XA29M60/XA29M84

RM-954 RM-953

TABLE OF CONTENTS

Section Title Page

SELF DIAGNOSIS FUNCTION................................ 4

1. GENERAL ........................................................................ 7

2. DISASSEMBLY

2-1. Rear Cover Removal ................................................ 43

2-2. Speaker Removal ..................................................... 43

2-3. Chassis Assy Removal ............................................. 43

2-4. F Bracket Removal .................................................. 43

2-5. Service Position ....................................................... 43

2-6. Replacement of Parts ............................................... 44

2-6-1 Replacement of Light Guide .............................................. 44

2-6-2 Replacement of Power Button ........................................... 44

2-7.

HV Cap Block, PWB Holder and J Board Removal ..

2-8. Terminal Bracket Removal ...................................... 44

2-9. D3 Board Removal .................................................. 44

2-10. P2 Board Removal ................................................... 44

2-11. B1 Board Removal ................................................... 45

2-12. H Board Removal .................................................... 45

2-13. A and B Boards Removal ........................................ 45

2-14. Picture Tube Removal .............................................. 46

2-15. Removal of Anode Cap............................................ 46

3. ADVANCE OPERATION

3-1. "RESET" Function ................................................... 47

4. SET-UP ADJUSTMENTS

4-1. Beam Landing .......................................................... 48

4-2. Convergence Adjustment ......................................... 49

4-3. Focus Adjustment .................................................... 51

4-4. G2 (Screen) and White Balance Adjustments......... 52

5. CIRCUIT ADJUSTMENTS

5-1. Adjustments with Commander ................................ 53

5-2. Adjustment Method ................................................. 53

5-3. Picture Quality Adjustments.................................... 58

5-4. Display position Adjustment ................................... 58

5-5. Deflection Adjustment ............................................. 58

5-6. H-Trapezoid Adjustment ......................................... 59

5-7. A Board Adjustment after IC003 Replacement ...... 59

5-8. Picture Distortion Adjustment ................................. 60

Section Title Page

6. DIAGRAMS

6-1. Block Diagram .......................................................... 61

6-2. Circuit Board Location ............................................. 65

6-3. Schematic Diagrams ................................................. 66

(1) Schematic Diagrams of F, J and VM Boards ..... 67

(2) Schematic Diagram of H Board ......................... 69

(3) Schematic Diagram of A Board.......................... 85

(4) Schematic Diagram of B Board ......................... 93

(5) Schematic Diagram of P2 Board ....................... 95

(6) Schematic Diagram of C6 Board ........................ 97

(7) Schematic Diagram of B1 and D3 Board ........... 99

6-4. Voltage Measurements............................................ 102

6-5. Waveforms .............................................................. 109

6-6. Printed Wiring Boards and Parts Location ............. 110

6-7. Semiconductors....................................................... 118

7. EXPLODED VIEWS

7-1. Picture Tube ............................................................ 120

7-2. Chassis .................................................................... 121

8. ELECTRICAL PARTS LIST .................................... 122

– 4 –

KV-XA29M60/XA29M84

RM-954 RM-953

The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER lamp will automatically begin to flash. The number of times the lamp flashes translates to a probable source of the problem. A definition of the STANDBY/TIMER lamp flash indicators is listed in the instruction manual for the user’s knowledge and reference. If an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past problems and how often these problems occur.

1. DIAGNOSTIC TEST INDICATORS

When an errors occurs, the STANDBY/TIMER lamp will flash a set number of times to indicate the possible cause of the problem. If there is more than one error, the lamp will identify the first of the problem areas.

Result for all of the following diagnostic items are displayed on screen. No error has occured if the screen displays a “0”.

Diagnostic

Item

Description

• Power does not turn on

• +B overcurrent (OCP) or overvoltage (OVP)

• Vertical deflection stopped

• Horizontal deflection overdrive

• White balance failure (no PICTURE)

• Micro reset

Detected

Symptoms

• Power does not come on.

• No power is supplied to the

TV.

• AC power supply is faulty.

• Power does not come on.

• Load on power line is

shorted.

• Has entered standby state after horizontal raster.

• Vertical deflection pulse is stopped.

• Power line is shorted or power supply is stopped.

• No raster is generated.

• CRT cathode current

detection reference pulse output is small.

• Power is shut down shortly, after this return back to normal.

• Detect Micro latch up.

Note 1: If a + B overcurrent is detected, stoppage of the vertical deflection is detected simultaneously.

The symptom that is diagnosed first by the microcontroller is displayed on the screen.

Note 2: Refer to screen (G2) Adjustment in section 3-4 of this manual.

* R(Q703), G(Q702) or B(Q701) out is faulty (C6 board).

SELF DIAGNOSTIC FUNCTION

No. of times

STANDBY/TIMER

lamp flashes

Does not light

2 times

5 times

—

Self-diagnostic

display/Diagnostic

result

—

002:000 or 002:001~255 003:001~255 004:001~255

at the same time

005:000 or 005:001~225

101:00 or

101:001~225

Probable

Cause

Location

• Power cord is not plugged in.

• Fuse is burned out F4601 (F)

• H.OUT Q511 is shorted. (A board)

• Q701, Q702, Q703 is shorted (C6 board)

• -13V is not supplied. (A board)

• IC 503 faulty (A board)

• G2 is improperly adjusted.

(Note 2)

• CRT problem.

• R(Q703), G(Q702) or

B(Q701) out is faulty (C6 board)

• IC301 is faulty. (A board)

• No connection A board to

C6 board.

• Discharge CRT (C6 Board)

• Static discharge

• External noise

– 5 –

KV-XA29M60/XA29M84

RM-954 RM-953

2. DISPLAY OF STANDBY/TIMER LIGHT FLASH COUNT

3. STOPPING THE STANDBY/TIMER FLASH

Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY/TIMER lamp from flashing.

4. SELF-DIAGNOSTIC SCREEN DISPLAY

For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it is possible to bring up past occurances of failure for confirmation on the screen:

[To Bring Up Screen Test]

In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:

[Screendisplay] / channel [5] / Sound volume [-] / Power ON

Note that this differs from entering the service mode (mode volume [+]).

Self-Diagnosis screen display

STANDBY/SLEEP lamp

Lamp ON 0.3 sec.

Lamp OFF 3 sec.

Lamp OFF 0.3 sec.

2 times

3 times

Diagnostic Item Flash Count*

+B overcurrent/overvoltage 2 times Vertical deflection stopped

White balance failure 5 times

* One flash count is not used for self-diagnostic.

002 : 000 003 : 000 004 : 000 005 : 001

Numeral "0" means that no fault has been detected.

Numeral "1" means a fault has been detected.

101 : 000

SELF DIAGNOSTIC

– 6 –

KV-XA29M60/XA29M84

RM-954 RM-953

5. HANDLING OF SELF-DIAGNOSTIC SCREEN DISPLAY

Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen during repairs. When you have completed the repairs, clear the result display to “0”.

Unless the result display is cleared to “0”, the self-diagnostic function will not be able to detect subsequent faults after completion of the repairs.

[Clearing the result display]

To clear the result display to “0”, press buttons on the remote commander sequentially as shown below when the diagnostic screen is being displayed.

Channel [8] / 0

[Quitting Self-diagnostic screen]

To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.

6. SELF-DIAGNOSTIC CIRCUIT

[+BovercurrentªOCPº] Occurs when an overcurrent on the +B(135) line is detected by Q604. If Q604 go to ON

and the voltage to pin 18 of IC301 should go down when V.SYNC is more than seven verticals in a period, the unit will automatically turn off.

[Verticaldeflectionstopped] Occurs when an absence of the vertical deflection pulse is detected by Q509 and IC001

shut down the power supply.

[Verticaldeflectionovercurrent] Occurs when an overcurrent on V drive line is detected by Q507. Power supply will be

shut down when detect this by IC001.

[Whitebalancefailure] If the RGB levels* do not balance or become low level within 5 seconds, this error will be

detected by IC301. TV will stay on, but there will be no picture.

* (Refers to the RGB levels of the AKB detection Ref pulse that detects IK.)

IC301

Y/CHROMA JUNGLE

FROM

CRT

[V] Q509/507

IC001

SYSTEM

IC003

MEMORY

IK-IN

MP/ PROTECT

O-LED

IO-8DAT B-DAT

IO-SDAT

521

SDA

FROM [+B] Q604 C6

– 7 –

KV-XA29M60/XA29M84

RM-954 RM-953

SECTION 1

GENERAL 1-2

(KV-XA29M84)

To prevent fire or shock hazard, do not expose the TV to rain or moisture.

Do not operate the TV if any liquid or solid object falls into it. Have it checked immediately by qualified personnel only.

Do not open the cabinet and the rear cover of the TV as high voltages and other hazards are present inside the TV. Refer servicing and disposal of the TV to qualified personnel.

Your TV is recommended for home use only. Do not use the TV in any vehicle or where it may be subject to excessive dust, heat, moisture or vibrations.

Do not block the ventilation openings of the TV. Do not install the TV in a confined space, such as a bookcase or built-in cabinet.

For children’s safety, do not leave children alone with the TV. Do not allow children to climb onto it.

Do not plug in too many appliances to the same power socket. Do not damage the power cord.

Clean the TV with a dry and soft cloth. Do not use benzine, thinner, or any other chemicals to clean the TV. Do not scratch the picture tube.

For your own safety, do not touch any part of the TV, the power cord and the antenna cable during lightning storms.

Pull the power cord out by the plug. Do not pull the power cord itself. Disconnect the TV before moving it or if you are not going to use it for several days.

WARNING

• Dangerously high voltages are present inside the TV.

• TV operating voltage: 110 – 240 V AC.

Do not install the TV in an unstable position. Use a proper TV stand.

Do not place any objects on the TV.

WARNING (continued)

The operating instruction mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of the Operating Instruction Manual remain as in the manual.

– 8 –

KV-XA29M60/XA29M84

RM-954 RM-953

Using Your New TV

123

VIDEO

VIDEO IN

VIDEO OUT

AUDIO

R L

Getting Started

CAUTION

• Do not connect the power cord until you have completed making all other connections; otherwise a minimum leakage current might flow through the antenna and other terminals to ground.

• To avoid battery leakage and damage to the remote, remove the batteries from the remote if you are not going to use it for several days. If any liquid that leaks from the batteries touches you, immediately wash it away with water.

Step 1

Connect the antenna

If you wish to connect a VCR, see the Connecting a VCR diagram below.

Connecting a VCR

To watch the video input, press t (see page 11).

IEC connector (not supplied)

To video and audio outputs

VCR

(yellow)

-L (MONO) (white)

-R (red)

To S video output

Antenna cable (not supplied)

To t 1, 2 or 3 (video input)

Audio/Video cable (not supplied)

S video cable (not supplied)

: Signal flow

To (S video input)

To antenna output

To 8 (antenna)

: Signal flow

Antenna cable (not supplied)

Rear of TV

Using Your New TV

PROGR

AUTO PROGR

NTER

SELECT

L(MONO)

AUTO PROGRAM PR : 01 TV SYS : B/G VHF LOW

Notes

• If you connect a monaural VCR, connect the yellow plug to

(the

yellow jack) and the black plug to

-L (MONO) (the white jack).

• If you connect a VCR to the 8 (antenna) terminal, preset the signal

output from the VCR to the program number 0 on the TV.

• If both

(S video input) and t 1 (video input) at the rear of your TV

are input at the same time, the

(S video input) is automatically

selected. To view the video input to t 1 (video input), disconnect the S video cable.

• Do not connect video equipment to t 3 (video input) at the front and

the rear of your TV at the same time; otherwise the picture will not be displayed properly on the screen.

• When no signal is input from the connected video equipment, the TV screen becomes blue.

Step 2

Insert the batteries into the remote

Note

• Do not use old batteries nor use different types of batteries together.

Step 3

Preset the channels automatically

Tips

• If you want to stop the automatic channel presetting, press MENU.

• If your TV has preset an unwanted channel or cannot preset a particular

channel, then preset your TV manually (see page 31).

Note

• During automatic channel presetting, your TV screen will indicate

“B/G”,

“I”, “D/K” or “M” for the TV system (

“TV SYS”).

Front of TV

– 9 –

KV-XA29M60/XA29M84

RM-954 RM-953

Using Your New TV

123

L(MONO)

Connecting optional components

You can connect optional audio/video components, such as a VCR, multi disc player, DVD, camcorder, video game or stereo system. To watch the picture of the connected equipment, press t (see page 11).

Connecting a camcorder/video game equipment using the t (video input) jacks

Notes

• You can also connect video equipment to the t 1, 2 or 3 (video input) jacks at the rear of your TV.

• If both

(S video input) and t 3 (video input) at the front of your TV

are input at the same time, the

(S video input) is automatically

selected. To view the video input to t 3 (video input), disconnect the S video cable.

• Do not connect video equipment to the t 3 (video input) jacks at the front and the rear of your TV at the same time; otherwise the picture will not be displayed properly on the screen.

Connecting audio/video equipment using the T (monitor output) jacks

Note

• If you select “DVD” on your TV scr

een, no signal will be output at the T

(monitor output) jacks (see page 11).

To S video output

Front of TV

Camcorder

Video game equipment

To video and audio outputs

(yellow)

-L (MONO)

(white)

-R (red)

Rear of TV

To antenna output

To video and audio inputs

Audio system

To audio inputs

VCR

: Signal flow

To (S video input)

3 (video input)

To T (monitor output)

Audio/Video cable (not supplied)

S video cable (not supplied)

Antenna cable (not supplied)

Audio/Video cable (not supplied)

PROGR

AUTO PROGR

ENTERSELECT

L(MONO)

L (MONO)

continued

Using Your New TV

Notes

• Some DVD player terminals may be labeled differently:

• Since the high quality pictures on a DVD disc contain a lot of information,

picture noise may appear. In this case, adjust the sharpness (

“SHARP”) in the

“ADJUST” menu of the “PICTURE MODE

” menu (see page 24).

• Connect your DVD player directly to your TV. Connecting the DVD player

through other video equipment will cause unwanted picture noise.

Connecting a DVD player using the

(component

video input) jacks

1 Connect R and L under

(component video input) on your TV to the LINE OUT,

AUDIO R and L output connectors on your DVD player.

2 Using a component video cable, connect Y, C

, and C

under

(component video

input) on your TV to the COMPONENT VIDEO OUT Y, C

, and C

output

connectors on your DVD player.

DVD player

To L (white) R (red)

Audio cable (not supplied)

To component video output

Component video cable (not supplied)

To audio output

: Signal flow

To (component video input)

Connect To (on the DVD player)

Y (green) Y C

(blue) C

, B-Y or P

CR (red) C

, R-Y or P

VIDEO

R-AUDIO-L

LINE OUT

COMPONENT VIDEO OUT

S VIDEO OUT

CB C

Rear of TV

Connecting a DVD player using the t (video input) jacks

VIDEO

R-AUDIO-L

LINE OUT

123

L(MONO)

DVD player

Audio/Video cable (not supplied)

(yellow)

-L (MONO) (white)

-R (red)

To t 1, 2, or 3 (video input)

: Signal flow

Rear of TV

Connecting optionals components (continued)

– 10 –

KV-XA29M60/XA29M84

RM-954 RM-953

Using Your New TV

Securing the TV

To prevent the TV from falling, secure the TV using one of the following methods:

With the supplied screws, attach the band to the TV stand and to the rear of the TV using the provided hole.

Put the cord or chain through the clamps to secure the TV against a wall or pillar.

Note

• Use only the supplied screws. Use of other screws may damage the TV.

20 mm

3.8 mm

Using Your New TV

Watching the TV

This section explains various functions and operations available while watching the TV. Most operations can be done using the remote.

Press

to turn on the TV.

When the TV is in the standby mode (the

indicator on the TV is lit red), press

?/1

on the

remote or PROGR +/

– on

the TV.

Press PROGR +/– or number buttons to select the program number.

For double digit numbers, press

, then the number

(e.g., for 25, press

, then

2 and 5).

To select a program number quickly

(1) Press and hold PROGR +/

–.

(2) Release PROGR +/

– when the desir

ed program number appears.

Note

• When you select a program number quickly, the picture may be disrupted.

This does not indicate a malfunction.

?/1

t a

Number buttons

JUMP

+/–

PROGR +/–

V/b/v/B/ENTER

indicator

-/--

FAVORITE

SOUND MODE

SURROUND

PIP PROGR

ENTER

PIC MODE

PROGRMENU

AUTO

PROGR

ENTER SELECT

L(MONO) R

PROGR

AUTO PROGR

ENTER SELECT

– 11 –

KV-XA29M60/XA29M84

RM-954 RM-953

Using Your New TV

Turn off temporarily

Turn off completely

Adjust the volume

Mute the sound

Watch the video input (VCR, camcorder, etc.)

Jump back to the previous program number

Display the on-screen information*

Press

?/1. The 1 indicator on the TV lights up red.

! on the TV.

2 +/–.

to select “VIDEO 1”, “VIDEO 2” , “VIDEO 3”or

“DVD”.

To return to the TV program, press

JUMP.

Additional tasks

ENTER

PICTURE++ MO C

PICTURE

INTELLIGENT PIC:OFF

WI DE MODE : OFF

DE : DYNAMI

COLOR SYS : AUTO

SETUP

PROGRAM SETUP

PIC ROTA T I ON

NGL I SH

LANGUAGE:

* The picture, sound, and either the program number or video input are

displayed. The on-screen display for the picture and sound information disappears after about three seconds.

Changing the menu language

You can change the menu language as well as the on-screen language.

For details on how to use the menu, see Introducing the menu system on page 20.

Press MENU.

Press V or v to select the “SETUP” icon ( ), then press ENTER.

Make sure “LANGUAGE” is selected, then press ENTER.

Press V or v to select the desired language (e.g.,

“

”), then press

ENTER.

The selected menu language appears.

To return to the normal screen

Press MENU.

LANGUAGE:

COLOR SYS :

SETUP

PROGRAM SE

PIC ROTA T I

ENGL ISH

continued

Using Your New TV

Setting the Wake Up timer

Press

until the desired

period of time appears.

The Wake Up timer starts immediately after you have set it.

Select the program number or video input you want to display when you wake up.

Press 1 or set the Sleep timer if you want the TV to turn off automatically.

The

indicator lights up orange.

To cancel the Wake Up timer

Press

until “WAKE UP TIMER: OFF” appears or turn off the TV’s

main power.

Note

• If no buttons or controls are pressed for more than two hours after the TV

is turned on using the Wake Up timer, the TV automatically goes into the standby mode. To continue watching the TV, press any button or control on the TV or the remote.

Setting the Sleep timer

Press until the desired period of time appears.

The Sleep timer starts immediately after you have set it.

To cancel the Sleep timer

Press

until “SLEEP TIMER: OFF” appears or turn the TV off.

WAKE UP TIMER:10M

WAKE UP TIMER:OFF

After 10 minutes

No Wake Up Timer

WAKE UP TIMER:12H00M

After 12 hours

SLEEP TIMER:30M

SLEEP TIMER:60M

SLEEP TIMER:OFF

SLEEP TIMER:90M

After 30 minutes

No Sleep Timer

After 60 minutes

After 90 minutes

Watching the TV (continued)

– 12 –

KV-XA29M60/XA29M84

RM-954 RM-953

Advanced Operations

SOUND MODE

PIC MODE

Selecting the picture and sound modes

You can select picture and sound modes and adjust the setting to your preference in “PERSONAL” option.

Selecting the picture mode

Press PIC MODE repeatedly until you get the desired picture mode.

Select To

“DYNAMIC” receive high contrast pictures.

“STANDARD” receive normal contrast pictures.

“SOFT” receive mild pictures.

“PERSONAL” receive the last adjusted picture setting from the “ADJUST”

option in the “PICTURE” menu (see page 23).

Selecting the sound mode

Press SOUND MODE repeatedly until you get the desired sound mode.

Select To

“DYNAMIC” listen to dynamic and clear sound that emphasizes the low and

high tones.

“DRAMA” listen to sound that emphasizes voice and high tones.

“SOFT” receive soft sound.

“PERSONAL ” receive the last adjusted sound setting from the “ADJUST”

option in the “SOUND” menu (see page 25).

Tip

• You can also set the picture and sound modes using the menu (see

Changing the “PICTURE” setting on page 23 and Changing the “SOUND” setting on page 25).

PERSONAL

SOFT

STANDARD

DYNAMIC

≥

DYNAMIC

≥

DRAMA

≥

SOFT

≥

PERSONAL

PIC MODE

Advanced Operations

Press FAVORITE.

Press the number button from 1 to 6 to select the desired favorite channel.

Tip

• To program your favorite channels, see Adjusting each program number

settings (PROGRAM SETUP) on page 29.

Viewing your favorite channels

You can display and select six of your favorite channels directly from your TV screen.

Number buttons

FAVORITE

-/--

FAVORITE

SOUND MODE

SURROUND

PIP PROGR

ENTER

PIC MODE

– 13 –

KV-XA29M60/XA29M84

RM-954 RM-953

Advanced Operations

Watching two programs at the same time

— PIP

With the Picture-in-Picture (PIP) feature, you can display a sub screen within the main picture of different TV programs or video inputs.

Displaying a sub screen

Press

To return to the normal screen

Press

(when displaying the sub screen).

V (PIP PROGR +)/ v (PIP PROGR –)

-/--

FAVORITE

SOUND MODE

SURROUND

PIP PROGR

ENTER

PIC MODE

Advanced Operations

continued

Advanced Operations

Additional PIP tasks

change the program number in the sub screen

select a video input in the sub screen

swap pictures between the main and sub screens

freeze the sub screen

Tips

• You can also display the sub screen and exchange pictures between the

main and sub screens using the menu (see Changing the “PIP” setting on page 27).

• You can change the position of the sub screen (see Changing the “PIP”

setting on page 27).

Notes

• When you display a video input on the sub screen at a faster/slower

speed, the picture may be disrupted depending on the VCR type.

• If you display different color systems on the sub screen, the size of the sub

screen may be different and the picture may be disrupted. This does not indicate a malfunction of the TV.

Press

V (PIP PROGR +) or v (PIP PROGR –).

To unfreeze the screen, press the

button again.

Watching two programs at the same time (continued)

– 14 –

KV-XA29M60/XA29M84

RM-954 RM-953

Advanced Operations

Press SURROUND repeatedly until you receive the desired surround sound.

Select To

“TruSurround” listen to the surround sound that spreads out to the rear of a room.

“OFF” turn off the surround sound.

Tip

• You can also select the surround option using the menu (see Changing the

“SOUND” setting on page 25).

The surround of your TV is categorized as TruSurround.

is a trademark of SRS Labs, Inc. SRS and the SRS symbol are

registered trademarks of SRS Labs, Inc. in the United States and selected foreign countries. SRS and TruSurround are incorporated under license from SRS Labs, Inc. and are protected under United States Patent Nos. 4,748,669 and 4,841,572 with numerous additional issued and pending foreign patents.

Listening with surround sound

The surround feature enables you to enjoy the sound effects of a concert hall or movie theater.

FAVORITE

SOUND

MODE

SURROUND

PIP PROGR

ENTER

SURROUND: OFF

SURROUND: TruSurround

SURROUND

Adjusting Your Setup (MENU)

Introducing the menu system

The MENU button lets you open a menu and change the settings of your TV. Here’s an overview of the menu system.

Level 1 Level 2 Level 3/Function

“PICTURE”

“PICTURE MODE

”

Select the picture mode:

“DYNAMIC”t “STANDARD”t “SOFT”t “PERSONAL”t “ADJUST”

“ADJUST” Adjust the “PERSONAL” option:

“PICTURE” t “COLOR”t “BRIGHT”t “HUE”t “SHARP”

“WIDE MODE” Change the picture size.

“INTELLIGENT PIC

”

Optimize picture quality.

“SOUND”“SOUND MODE

”

Select the sound mode:

“DYNAMIC”t “DRAMA” t “SOFT” t “PERSONAL“ t “ADJUST”

“ADJUST” Adjust the “PERSONAL” option:

“BASS” t “TREBLE”t “BALANCE”t “BBE”

“SURROUND” Select the surround mode:

“TruSurround” t “OFF”

“INTELLIGENT VOL

”

Adjust volume automatically.

“PIP”“POSITION” Change the position of the sub screen.

“PIP” Display a sub screen within the main picture.

“SWAP” Exchange pictures between main screen and sub

screen.

“SETUP”“LANGUAGE” Change the menu language:

“ENGLISH” t“

”(Chinese) t “

”(Arabic) t

“

” (Thai)

“PIC ROTATION” Rotate the picture.

“PROGRAM SETUP

”

Adjust each program number settings.

“COLOR SYS” Change the color system:

“AUTO” t “PAL ” t “SECAM” t “NTSC3.58” t “NTSC4.43”

Return icon

“PICTURE” icon

“PIP” icon

“CH PRESET” icon

Name of the current menu

Menu level 3

Menu level 2

Adjusting Your Setup (MENU)

Menu level 1

“SETUP” icon

Menu guide icon

LA NGUAGE :

COLOR SYS :

SETUP

PROGRAM SE

PIC ROTA T I

ENGL ISH

“SOUND” icon

– 15 –

KV-XA29M60/XA29M84

RM-954 RM-953

Adjusting Your Setup (MENU)

Level 1 Level 2 Level 3/Function

“CH PRESET”“AUTO PROGRAM” Preset channels automatically.

“MANUAL PROGRAM

”

Preset channels manually.

“TV SYS” Change the TV system:

“B/G” t “I” t “D/K” t “M”

The BBE is manufactured by Sony Corporation under license from BBE Sound, Inc. It is covered by U.S. Patent No. 4,638,258 and No. 4,482,866. The word “BBE” and the BBE symbol are the trademarks of BBE Sound, Inc.

continued

Adjusting Your Setup (MENU)

How to use the menu

You can use the buttons on the remote and on the TV as well to display the menu and adjust the settings.

Press MENU to display the menu.

Press V or v to select the desired item.

Press ENTER to confirm your selection and go to the next menu level.

Other menu operations

To Press

Adjust the setting value V ,b,v or B

Move to the next/previous menu level b or B

Cancel the menu MENU

Tips

• If you want to exit from Menu Level 2 to Menu Level 1, press V or v until

the return icon (

) is highlighted, then press ENTER.

•

Some of the menu items can be operated directly using the remote buttons.

• The MENU, ENTER, and SELECT

buttons on the TV can also be used

for the operations above.

Note

• If more than 60 seconds elapse between entries, the menu screen

automatically disappears.

PROGRMENU

AUTO

PROGR

ENTER SELECT

CH PRESET

SYS:B/G

MANUAL PROGRAM

AM+++

OPROGAUT

V/b/v/B/ENTER

Front of TV

RAM

UHF

MANUA LPROG

SENS :H IGH

TV SYS: B /G

FINE:AUTO

PR :

ENTER

FAVORITE

PIP PROGR

ENTER

PICTURE++ MO C

PICTURE

INTELLIGENT PIC:OFF

WI DE MODE : OFF

DE : DYNAMI

Introducing the menu system (continued)

– 16 –

KV-XA29M60/XA29M84

RM-954 RM-953

Adjusting Your Setup (MENU)

INTELLIGEN

PER

PICTURE

SONAL

WI DE

SOF T

PICTUR

MOD E

S TANDARD

ADJ UST

DYNAMI

FAVORITE

PIP PROGR

ENTER

Changing the “PICTURE” setting

The “PICTURE” menu allows you to change the picture settings.

Press MENU.

Make sure the

“PICTURE”

icon (

) is selected,

then press ENTER.

Press V or v to select the desired item (e.g.,

“PICTURE MODE

” )

then press ENTER.

Select To

“PICTURE MODE

”

choose either “DYNAMIC”, “ST

ANDARD”, “SOFT”,

“PERSONAL”*, or “ADJUST”.

“WIDE MODE”

change the picture size when receiving wide-mode (16:9) picture signal. Press V or v to select “ON”, then press ENTER. To cancel, select “OFF”, then pr

ess ENTER.

“INTELLIGENT PIC

”

optimize picture quality. Press V or v to select “ON”, then press ENTER. To cancel, select

“OFF”, then pr

ess ENTER.

* When the “PERSONAL” mode is selected, you can r

eceive the last

adjusted picture settings from the “ADJUST” option (see page 24).

Note

• For details on the options under

“PICTURE MODE

”, see page 13.

To return to the normal screen

Press MENU.

ENTER

V/b/v/B/ENTER

PICTURE MO C

PICTURE

INTELLIGENT PIC:OFF

WIDE MODE:OFF

DE : DYNAMI

continued

Adjusting Your Setup (MENU)

COLOR

Adjusting the

“ADJUST” items under

“PICTURE MODE

”

Press V or v to select the desired item (e.g., “COLOR”), then press ENTER.

Adjust the value according to the following table, then press ENTER.

For Press v/B to Press V/b to

“PICTURE” decrease picture contrast increase picture contrast

“COLOR” decrease color intensity increase color intensity

“BRIGHT” darken the picture brighten the picture

“HUE”* increase red picture tones increase green picture tones

“SHARP” soften the picture sharpen the picture

* You can adjust “HUE” for the NTSC color system only

Repeat the above steps to adjust other items.

The adjusted settings will be received when you select

“PERSONAL”.

Tip

• For details on the menu system and how to use the menu, refer to

Introducing the menu system on page 20.

ENTER

Changing the “PICTURE” setting (continued)

– 17 –

KV-XA29M60/XA29M84

RM-954 RM-953

Adjusting Your Setup (MENU)

FAVORITE

PIP PROGR

ENTER

Changing the “SOUND” setting

The “SOUND” menu allows you to change the sound settings.

Press MENU.

Press V or v to select the

“SOUND” icon (

then press ENTER.

Press V or v to select the desired item (e.g., “SOUND MODE”), then press ENTER.

Select To

“SOUND MODE

”

choose either “DYNAMIC”, “DRAMA”, “SOFT”, “PERSONAL”*, or “ADJUST”.

“SURROUND” choose either “TruSurround” or “OFF”.

“INTELLIGENT VOL

”

adjust the volume of all program numbers and video inputs automatically. Press V or v to select “ON”, then press ENTER. To cancel, select

“OFF”, then pr

ess ENTER.

* When the “PERSONAL” mode is selected, you can r

eceived the last

adjusted sound settings from the “ADJUST” option (see page 26).

Tip

• For details on the options under

“SOUND MODE

” and “SURROUND”,

see pages 13 and 17 respectively.

To return to the normal screen

Press MENU.

V/b/v/B/ENTER

ENTER

SOUND MODE +

SOUND

INTELLIGENT VOL:OFF

SURR OUND: OF F

: DYNAMI C+

PER

SOUND

SONAL

INTELLIGENSOFT

URROUND :O

OUND MODE

DRAMA

ADJ UST

DYNAMI

ENTER

continued

Adjusting Your Setup (MENU)

Adjusting the

“ADJUST” items under

“SOUND MODE

”

Press V or v to select the desired item (e.g., ”BALANCE“), then press ENTER.

Adjust the value according to the following table, then press ENTER.

For Press v/B to Press V/b to

“BASS” decrease the bass increase the bass

“TREBLE” decrease the treble increase the treble

“BALANCE” increase the left speaker’s volume

increase the right speaker’s volume

“BBE” select “HIGH” for higher enhancement of sound clarity;

select “LOW” for lower enhancement of sound clarity; select “OFF” to turn off the BBE sound

Repeat the above steps to adjust other items.

The adjusted settings will be received when you select

“PERSONAL”.

Tip

• For details on the menu system and how to use the menu, refer to

Introducing the menu system on page 20.

BALANCE 00

ENTER

Changing the

“SOUND” setting (continued)

– 18 –

KV-XA29M60/XA29M84

RM-954 RM-953

Adjusting Your Setup (MENU)

PIP

SWAP

PIP:OFF

POS I T ION :

-/--

FAVORITE

SOUND MODE

SURROUND

PIP PROGR

ENTER

Changing the “PIP” setting

The “PIP” menu allows you to display a sub screen, change the sub screen position and exchange pictures between the main and sub screens.

Press MENU.

Press V or v to select the “PIP” icon (

), then

press ENTER.

Press V or v to select the desired item (e.g.,

“PIP”),

then press ENTER.

V/b/v/B/ENTER

ENTER

OFF

PIP

SWAP

PIP:

POSI T ION :

Select To

“POSITION” change the position of the sub screen.

Press V or v to select the desired position, then press ENTER.

“PIP” display a sub screen within the main picture.

Press V or v to select “ON”, then pr

ess ENTER.

To cancel, press

or select “PIP : OFF”, then press ENTER.

“SWAP” exchange pictures between main screen and sub screen.

To return to the normal screen

Press MENU.

Tip

• For details on the menu system and how to use the menu, refer to

Introducing the menu system on page 20.

Adjusting Your Setup (MENU)

Changing the “SETUP” setting

The “SETUP” menu allows you to change the menu language, adjust the picture position, adjust the program number setting and select color system.

-/--

FAVORITE

PIP PROGR

ENTER

Number buttons

V/b/v/B/ENTER

Press MENU.

Press V or v to select “SETUP” icon (

then press ENTER.

Press V or v to select the desired item (e.g., “COLOR SYS”), then press ENTER.

Select To

“LANGUAGE” change the menu language (see Changing the menu language

on page 11).

“PIC ROTATION” adjust the picture position when it is not aligned to the TV screen.

Press V, b, v or B to adjust the picture position, then press ENTER.

“PROGRAM SETUP

”

adjust each program number settings. (see Adjusting each program number settings (PROGRAM SETUP) on page 29).

“COLOR SYS” change the color system. Normally, set this to “AUTO”.

To return to the normal screen

Press MENU.

ENTER

COLOR SYS : AUTO

SETUP

PROGRAM SETUP

PIC ROTA T I ON

NGL I SH

LANGUAGE:

LANGUAGE: E

COLOR SYS : NTS

SETUP

C3.58

PROGRAM SE SECAM

PIC ROTA T I PAL

AUTO

NTSC4.43

– 19 –

KV-XA29M60/XA29M84

RM-954 RM-953

Adjusting Your Setup (MENU)

Adjusting each program number settings (PROGRAM SETUP)

Select “PROGRAM SETUP

” from the “SETUP” menu.

Select “PR” and press ENTER. Press V or v to select the desired program number you want to adjust, then press ENTER.

Press V or v to select the desired item (e.g., ”CHILD LOCK”), then press ENTER.

Select To

“PR” select the desired program number.

“SKIP” skip unwanted or unused program number.

Press V or v to select “ON”, then pr

ess ENTER.

To cancel, select “OFF”, then pr

ess ENTER.

“CHILD LOCK”

prevent children from watching this selected program number. Press V or v to select “ON”, then pr

ess ENTER.

The lock symbol (

) appears on the screen.

To cancel, select “OFF”, then pr

ess ENTER. If you preset a locked program number, that program number will be unlocked automatically.

“FAVORITE CH” program favorite channels for direct selection.

Press V or v to select one of the six favorite channel numbers (if you decide not to make any changes, select

“

”), then press ENTER. To view the selected favorite channel, refer page 14.

To continue adjusting other program number, press V or v to select “PR”, then repeat step 2 and 3.

To return to the normal screen

Press MENU.

FAVORI TE CH: ––

PROGRAM SE T

CH I LD L OCK :OFF

SK I P:OFF

PR : 14

ENTER

FAVORI TE C : ––

PROGRAM SE T

CH I LD L OCK :

SK I P:ON

PR : 14

OFF

Adjusting Your Setup (MENU)

Press MENU.

Press V or v to select the “CH PRESET” icon (

then press ENTER.

Press V or v to select the desired item (e.g.,

“AUTO PROGRAM

”),

then press ENTER.

Select

“AUTO PROGRAM”

“MANUAL PROGRAM

”

“TV SYS”

To return to the normal screen

Press MENU.

Tip

• For details on the menu system and how to use the menu, refer to

Introducing the menu system on page 20.

RAM

AUTO PROG

FLOW

SYS : B/ G

01:

CH PRESET

SYS:B/G

MANUAL PROGRAM

AM+ ++

OPROGAUT

preset channels automatically.

preset channels manually. See Presetting channels manually on page 31.

change the TV system. Press V or v to select either “B/G”, “I”, “D/K” or “M”, then press ENTER.

Changing the Channel Preset (“CH PRESET”) setting

The “CH PRESET” menu allows you to adjust the setup of your TV. For example, you can receive a channel with a weak signal that fails to be tuned in by automatic presetting.

FAVORITE

SOUND MODE

SURROUND

PIP PROGR

ENTER

V/b/v/B/ENTER

ENTER

– 20 –

KV-XA29M60/XA29M84

RM-954 RM-953

Adjusting Your Setup (MENU)

Presetting channels manually

After selecting

“MANUAL PROGRAM”, select the program number to which you want to preset a channel.

(1) Make sure “PR” is

selected , then press ENTER.

(2)

Press V or v until the program number you want to preset (e.g., program number “10”) appears on the menu, then press ENTER.

Tip

• You can also select the program number with the PROGR +/

– or number buttons.

Select the desired channel.

(1) Make sure either

“VHF LOW”,

“VHF

HIGH” or “UHF” is selected,

then press

ENTER.

(2) Press V or v until the

desired channel picture appears on the TV screen, then press ENTER.

If the sound of the desired channel is abnormal, select the appropriate TV system.

(1) Press V or v to select

“TV SYS”, then press ENTER.

(2) Press V or v until the

sound becomes normal (e.g., “M”), then press ENTER.

01:

RAM

VHF

MANUA LPROG

SENS :H IGH

TV SYS:B/G

FINE:AUTO

LOW

10:

RAM

VHF

MANUA LPROG

SENS :H IGH

TV SYS:B/G

FINE:AUTO

LOW

ENTER

10:

RAM

VHF

MANUA LPROG

SENS :H IGH

TV SYS: B /G

FINE:AUTO

LOW

10:

RAM

VHF

MANUA LPROG

SENS :H IGH

TV SYS:B/G

FINE:AUTO

LOW

10:

RAM

VHF

MANUA LPROG

SENS :H IGH

TV SYS :M

FINE:AUTO

LOW

10:

RAM

VHF

MANUA LPROG

SENS :H IG /K

TV SYS : I

B/G

FINE:AUTO

LOW M

ENTER

continued

Adjusting Your Setup (MENU)

If you are not satisfied with the picture and sound quality, you may improve them by using fine tuning.

(1)

Press V or v to select “FINE”, then press ENTER

(2)

Press V or v to select “MANUAL”, then press ENTER.

(3) Press V, b, v or B until

the picture and sound quality are optimal, then press ENTER.

The + or – icon on the menu flashes while tuning.

If the TV signal is too strong and the picture is distorted, you may reduce the TV receiving sensitivity.

(1) Press V or v to select

“

SENS”, then

press ENTER.

(2) Press V or v to select

“LOW”, then press ENTER.

To return to the normal screen

Press MENU.

Notes

• If you preset a locked program number (

“CHILD LOCK”), that particular

program number will be unlocked automatically (see page 29).

• The TV system (

“TV SYS”),

“

SENS” and the fine tuning (

“FINE”)

settings are memorized for each program number.

10:

RAM

VHF

MANUA LPROG

SENS :LOW

TV SYS: M

F INE :MANUAL

LOW

10:

RAM

VHF

MANUA LPROG

SENS :

TV SYS: M LOW

HIGH

F INE :MANUA

LOW

10:

RAM

VHF

MANUA LPROG

SENS: HI GH

TV SYS: M

FINE:MANUA L

LOW

10:

RAM

VHF

MANUA LPROG

SENS: HI G –+

TV SYS: M MANUA L

AUTO

FINE:

LOW

10:

RAM

VHF

MANUA LPROG

SENS :H IG

TV SY S :M MANUAL

AUTO

FINE:

LOW

ENTER

Changing the Channel Preset (“CH PRESET”) setting (continued)

– 21 –

KV-XA29M60/XA29M84

RM-954 RM-953

Additional Information

Self-diagnosis function

Your TV is equipped with a self-diagnosis function. If there is a problem with your TV, the 1 indicator flashes red. The number of times the 1 indicator flashes indicates the possible causes.

Check that the 1 indicator flashes red a number of times between 3-second intervals.

Count the number of times the 1 indicator flashes.

Press ! (main power) to turn off your TV.

Inform your nearest Sony service center about the number of times the 1 indicator flashes. Be sure to note the model name and serial number located on the rear of your TV.

Front of TV

indicator

PROGRMENU

AUTO

PROGR

ENTER SELECT

L(MONO)

Additional Information

Troubleshooting

If you find any problem while viewing your TV, please check the following guide. If any problem persists, contact your Sony dealer.

Possible cause

Symptom

Solutions

• Connection is loose or the cable is damaged.

• Channel presetting is inappropriate or incomplete.

• The antenna type is inappropriate.

• The antenna direction is inappropriate.

• Signal transmission is low.

• Broadcast signals are too strong.

• The TV system setting or channel presetting is inappropriate or incomplete.

• The power cord, antenna or VCR is not connected.

• The TV is not turned on.

• Check the antenna cable and connection on the TV, VCR and on the wall.

• Display the “CH PRESET” menu and select “MANUAL PROGRAM” to preset the channel again.

• Check the antenna type (VHF/UHF). Contact a Sony dealer for advice.

• Adjust the antenna direction. Contact a Sony dealer for advice.

• Try using a booster.

• Display the “CH PRESET” menu and select “MANUAL PROGRAM

”. Then,

select “

SENS: LOW”.

• Turn off or disconnect the booster if it is in use.

• If the sound of all the channels are noisy, display the “CH PRESET” menu and check the TV system (

“TV SYS”) setting, then select “AUTO PROGRAM” to preset the channels again.

• If the sound of some channels are noisy, select the channel, then display the

“CH PRESET” menu and select the appropriate TV system (“TV SYS”).

• Check the power cord, antenna and the VCR connections.

• Press ?/1 (power).

• Press ! (main power) on the TV to turn

off the TV for about five seconds, then turn it on again.

Snowy picture

Noisy sound

Distorted picture

Noisy sound

Good picture

Noisy sound

No picture

No sound

Page

–

– 22 –

KV-XA29M60/XA29M84

RM-954 RM-953

Additional Information

Possible causeSymptom

Solutions

• Press 2 + to increase the volume level.

• Press % to cancel the muting.

• Do not use a hair dryer or other

equipment near the TV.

• Adjust the antenna direction for minimum interference. Contact a Sony dealer for advice.

• Use a highly directional antenna.

• Use the fine tuning (

“FINE”) function.

• Adjust the antenna direction. Contact a

Sony dealer for advice.

• Turn off or disconnect the booster if it is in use.

• Display the “PICTURE” menu and select “ADJUST” of “PICTURE MODE

”, then

adjust the “COLOR” level.

• Display the “SETUP” menu and check the

color system (“COLOR SYS”) setting (usually set this to

“AUT

O”).

• Adjust the antenna direction. Contact a Sony dealer for advice.

• Keep external speakers or other electrical equipment away from the TV. Do not move the TV while the TV is turned on. Press ! (main power) on the TV to turn off the TV for about five minutes, then turn it on again.

Page

–

Good picture

No sound

Dotted lines or stripes

Double images or “ghosts”

No color

Abnormal color patches

continued

• The volume level is too low.

• The sound is muted.

• There is local

interference from cars, neon signs, hair dryers, power generators, etc.

• Broadcast signals are reflected by nearby mountains or buildings.

• The antenna direction is inappropriate.

• Use of a booster is inappropriate.

• The color level setting is too low.

• The color system setting is inappropriate.

• The antenna direction is inappropriate.

• The magnetic disturbance from external speakers or other equipment, or the direction of the earth’s magnetic field may affect the TV.

Additional Information

Possible causeSymptom

Solutions

Troubleshooting (continued)

Page

—

• Check the antenna cable and connection

on the TV, VCR and on the wall.

• Adjust the antenna direction. Contact a Sony dealer for advice.

• Try using a booster.

• Use the fine tuning (

“FINE”) function.

• Keep external speakers or other electrical

equipment away from the TV.

• Display the “SETUP” menu and adjust “PIC ROTATION” so that the picture is

aligned to the TV screen.

• Use the fine tuning (

“FINE”) function.

• Contact your nearest Sony service center.

—

“100” appears on the top of the screen and no Teletext display. (Not used for this model)

Teletext display is incomplete (picture snowy or double images). (Not used for this model)

Picture slant

Lines moving across the TV screen.

The 1 indicator on your TV flashes red a number of times between 3-second intervals.

TV cabinet creaks.

A “boom” sound is heard when the TV is turned on.

–

• The channel carries no

Teletext broadcast.

• Connection is loose or the cable is damaged.

• The antenna direction is inappropriate.

• Signal transmission is too low.

• The magnetic disturbance from external speakers or other equipment, or the direction of the earth’s magnetic field may affect the TV.

• There is interference from external sources, e.g., heavy machineries, nearby broadcast station.

• Your TV may need service.

• Changes in room temperature sometimes make the TV cabinet expand or contract, making a noise. This does not indicate a malfunction.

•

The TV’s demagnetizing function is working. This does not indicate a malfunction.

– 23 –

KV-XA29M60/XA29M84

RM-954 RM-953

Additional Information

Overview of controls

TV front panel

L (MONO)

PROGRMENU

AUTO PROGR

ENTER SELECT

L(MONO)

PROGRMENU

AUTO PROGR

ENTER SELECT

PageFunction

Preset channels automatically.5 Turn off completely or 10

turn on the TV. Select program number. 10 Standby indicator.10 Adjust volume. 11 Select TV or video input. 11 Wake Up indicator.12 Display the menu. 22 Headphones jack. –

AUTO PROGR

PROGR +/–

1 2 +/–

Button

continued

Additional Information

Remote control

-/--

FAVORITE

SOUND

MODE

SURROUND

PIP PROGR

ENTER

PIC MODE

The names/symbols of buttons on the remote are indicated in different colors to represent the available functions.

Label color

White

Green

Yellow

Button function

For general TV operations

For Teletext operations

For PIP operations

Page

Button

Function

Overview of controls (continued)

Turn off temporarily or turn on the TV.

Select program number. Input numbers. Adjust volume. Select TV or video input. Display the TV program. Mute the sound. Display on-screen information. Jump to previous program

number.

Set TV to turn on automatically. Set TV to turn off automatically. Select picture mode. Select sound mode. Display favorite channels.

Display a sub screen. Swap main and sub screens. Freeze the sub screen. Select video input for the sub screen. Change program number in the sub

screen. Select surround mode.

Select stereo/bilingual mode.

Display Teletext broadcast. Enlarge the Teletext display. Reveal concealed information. Stop Teletext page from scrolling. Display Teletext service contents. Show TV screen while waiting

for Teletext page. Input

Teletext page

number.

Display the next or previous page.

Access a FASTEXT menu.

Display the menu. Select, adjust and confirm

selected item.

10 10 11 11 11 11 11 11

12 12 13 13 14

15 16 16 16 16

–

18 19 19 19 19 19

19 19

22 22

?/1

PROGR +/– 0 – 9, 2 +/–

t a

JUMP

Timer operations

PIC MODE SOUND MODE FAVORITE

PIP operations

V/v

(PIP PROGR +/–) SURROUND Stereo/bilingual operations

(not used for used this model)

A/B Teletext operations

(not used for this model)

0 – 9

PROGR +/–

(red, green,

yellow, blue)

Menu operations

V/b/v/B/ENTER

– 24 –

KV-XA29M60/XA29M84

RM-954 RM-953

GENERAL 2-2

(KV-XA29M60)

The operating instruction mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of the Operating Instruction Manual remain as in the manual.

WARNING

• Dangerously high voltages are present inside the TV.

• TV operating voltage: 220

– 240 V

AC.