2-653-742-11 (1)
Trinitron Color TV
Operating Instructions |
|
GB |
•Before operating the unit, please read this manual thoroughly and retain it for future reference.
Mode d’emploi |
|
FR |
•Avant de faire fonctionner cet appareil, lisez attentivement le présent mode d’ emploi et conservez-le pour toute référence ultérieure.
AR
!*) ( ' &%$# " ! , •
/.- ,%+
KV-SW21
KV-BZ21 M81
M80
© 2005 Sony Corporation
WARNING
•Dangerously high voltages are present inside the TV.
•TV operating voltage: 110 – 240 V AC.
•Do not plug in the power cord until you have completed making all other connections; otherwise a minimum leakage current might flow through the antenna and other terminals to ground.
•To avoid battery leakage and damage to the remote, remove the batteries from the remote if you are not going to use it for several days. If any liquid leaks from the batteries and touches your skin, immediately wash it away with water.
For your own safety, do not touch |
For children’s safety, do not leave |
To prevent fire or shock hazard, do |
any part of the TV, the power cord |
children alone with the TV. Do not |
not expose the TV to rain or |
and the antenna cable during |
allow children to climb onto it. |
moisture. |
lightning storms. |
|
|
Do not place any objects on the TV. |
Do not operate the TV if any liquid |
Install the TV on a stable TV stand |
The apparatus shall not be |
or solid object falls into it. Have it |
and floor which can support the |
exposed to dripping or splashing |
checked immediately by qualified |
TV set weight. Ensure that the TV |
and that no objects filled with |
personnel only. |
stand surface is flat and its area is |
liquids, such as vases, shall be |
|
larger than the bottom area of the |
placed on the apparatus. |
|
TV. |
Do not block the ventilation |
Your TV is recommended for |
Do not plug in too many |
openings of the TV. Do not install |
home use only. Do not use the TV |
appliances to the same power |
the TV in a confined space, such |
in any vehicle or where it may be |
socket. Do not damage the power |
as a bookcase or built-in cabinet. |
subject to excessive dust, heat, |
cord. |
|
moisture or vibrations. |
|
Do not open the cabinet and the |
Clean the TV with a dry and soft |
Pull the power cord out by the |
rear cover of the TV as high |
cloth. Do not use benzine, thinner, |
plug. Do not pull the power cord |
voltages and other hazards are |
or any other chemicals to clean the |
itself. Even if your TV is turned |
present inside the TV. Refer |
TV. Do not attach anything (e.g., |
off, it is still connected to the AC |
servicing and disposal of the TV |
adhesive tape, cellophane tape, |
power source (mains) as long as |
to qualified personnel. |
glue) on the painted cabinet of the |
the power cord is plugged in. |
|
TV. Do not scratch the picture |
Unplug the TV before moving it |
|
tube. |
or if you are not going to use it for |
|
|
several days. |
2
Table of Contents
Securing the TV ............................................................................................................... |
4 |
|
Getting Started ................................................................................................................ |
4 |
|
Setting up your TV (“Initial Setup”) ............................................................................ |
5 |
|
TV top control, front and rear panels .......................................................................... |
7 |
|
Connecting optional components ................................................................................ |
8 |
|
Using the remote control and basic functions .......................................................... |
10 |
|
Introducing the WEGA GATE navigator .................................................................. |
12 |
|
“Settings” Adjustment ................................................................................................. |
13 |
|
Changing the “Picture” setting ................................................................................... |
14 |
|
Changing the “Sound” setting .................................................................................... |
15 |
|
Changing the “Channel Setup” setting ..................................................................... |
16 |
|
Changing the “Setup” setting |
18 |
|
GB |
||
............................................................................................................Viewing Teletext |
19 |
|
Troubleshooting ............................................................................................................ |
20 |
|
Specifications .................................................................................................. |
Back cover |
|
3
x Securing the TV
To prevent the TV from falling, use the supplied screws, clamps and band to secure the TV. Use only the supplied screws. Use of other screws may damage the TV.
|
20 mm |
|
screws |
3.8 mm |
|
clamps |
band |
|
or (1) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Screw the band to the TV stand and |
Put a cord or chain through the |
||||
to the provided hole at the rear of |
|
clamps. |
|||
your TV. |
(2) |
Screw one clamp to a wall or pillar |
|||
|
|
and the other clamp to the provided |
|||
|
|
hole at the rear of your TV. |
x Getting Started
Step 1
Insert the batteries (supplied) into the remote.
b
Note
•Do not use old or different types of batteries together.
Step 2
Connect the antenna cable (not supplied) to 8 (antenna input) at the rear of the TV.
Tip
•You can also connect your TV to other optional components (see page 8).
b
Step 3
Plug in the power cord, then press ! on the TV to turn it on.
Note
•The 1 (standby) indicator flashes green for a few seconds when turning on the TV. This does not indicate a malfunction.
Step 4
Set up the TV by following the instructions of the “Initial Setup” menu (see page 5).
Select |
Confirm |
End |
4
x Setting up your TV (“Initial Setup”)
When you turn on your TV for the first time, the “Initial Setup” menu will appear. You may change the menu language, preset the TV channels automatically, sort or edit the channels and adjust the picture position using the buttons on the remote control or TV top control panel.
1 |
Press V or v to select the desired menu |
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
||||
|
|
||||||
|
language, then press . |
|
|
The selected menu language appears.
Select |
Confirm |
End |
2 |
Press V or v to select “Yes”, then press |
|
to preset the channels automatically. |
The screen will indicate automatic presetting is in progress.
After all available channels have been tuned and stored, the “Program Sorting/Edit” menu appears automatically on the screen.
To skip automatic channel presetting, select “No”, then press .
Select Confirm End
|
|
Program: |
01 |
TV System: |
Auto |
VHF Low |
|
|
|
|
End |
If the message “No channel found. Please connect cable/antenna” appears, check your TV connections, then press .
3 |
The “Program Sorting/Edit” menu enables |
|
|
you to sort and edit the channels. |
|
|
a) If you wish to keep the channels in the |
|
|
|
current condition, press WEGA GATE |
|
|
to exit. |
|
b) |
Press V or v to select the program |
|
|
number with the channel you wish to |
|
|
change. The selected channel will |
|
|
appear on the screen. |
|
c) |
If you wish to store the channels in a |
|
|
different order: |
1) Press b to enter sorting mode.
2) Press V or v to select the new program number position for your selected channel, then press B.
Program Sorting/Edit |
|
|||
PROG |
Label |
Skip |
|
|
01 |
|
|
Off |
|
02 |
|
|
Off |
|
03 |
|
|
Off |
|
04 |
|
|
Off |
|
Sorting: |
Edit: |
|
||
Select |
|
|
Confirm |
Exit |
Program Sorting/Edit
PROG |
Label |
Skip |
|
01 |
|
Off |
|
02 |
|
Off |
|
03 |
01 |
|
Off |
04 |
|
Off |
|
Sorting mode |
|
|
|
Select |
|
Confirm |
Exit |
continue
5
Setting up your TV (“Initial Setup”) (continued)
d)If you wish to edit the channels, press to change to edit mode.
Press b until the mode that you wish to edit
is highlighted: Label, Skip, (block symbol). Then press .
1)To label, press V or v to select the alphanumeric characters for the label. Then press .
2)To skip the program number, press V or v to select “On”. Then press .
You can skip this program number when using PROG +/–.
3)To block unwanted program number, press V or v to select . Then press .
e)Repeat step b) to d) if you wish to change other channels.
Press WEGA GATE to go to the next menu.
Select Confirm Exit
Select Confirm Exit
Select Confirm Exit
4 |
Press B or b to adjust the bars on the top |
|
and bottom of the menu if they are |
|
slanted, then press (KV-SW21M81only). |
If no adjustment is necessary, then press .
Select |
Confirm |
End |
5 To prevent this “Initial Setup” menu from appearing again when you turn on the TV by pressing !, press V or v to select “No”, then press .
To allow this menu to appear again, select “Yes”, then press .
Select Confirm
Tip
• You can immediately go to the end of the ”Initial Setup” menu by pressing WEGA GATE.
6
xTV top control, front and rear panels
TV top control panel
WEGA GATE
SOUND MODE |
PROG |
0 9 8 7 6
TV front panel
2
L (MONO) |
R |
|
|
5 |
4 |
3 2 |
1 |
TV rear panel
1 |
|
|
|
|
Y |
|
|
CB |
(MONO) L |
|
L (MONO) |
|
|
CR |
R |
|
R |
|
|
qa |
qf |
qd |
qs |
Button/Terminal |
|
Function |
|
Page |
|
1 |
! |
|
Turn off or turn on the TV. |
|
4 |
|
|
|
|
|
|
2 |
|
|
Remote control sensor. |
|
- |
|
|
|
|
|
|
3 |
|
|
Wake Up indicator. |
|
11 |
|
|
|
|
|
|
3 |
1 |
|
Standby indicator. |
|
4 |
|
|
|
|
|
|
4 i |
|
Headphone jack. |
|
- |
|
|
|
|
|
|
|
5 t2 |
|
Video input terminal 2. |
|
8 |
|
|
|
|
|
|
|
6 PROG +/– |
|
Select program number. |
|
- |
|
|
|
|
|
|
|
7 |
2 +/– |
|
Adjust volume. |
|
- |
|
|
|
|
|
|
8 t |
|
Select TV or video input. |
|
8 |
|
|
|
|
|
|
|
WEGA GATE menu operations |
|
|
|||
|
6,7 V,v,B,b |
|
Select and adjust items. |
|
12 |
|
|
|
|||
|
|
|
|
|
|
|
8 |
|
Confirm selected items. |
|
12 |
|
|
|
|
|
|
|
9 WEGA GATE |
|
Display or cancel WEGA GATE menu. |
|
12 |
|
|
|
|
|
|
0 SOUND MODE |
|
Select sound mode options with a 5-Band Graphic |
|
10 |
|
|
|
|
Equalizer display. |
|
|
|
|
|
|
|
|
qa 8 |
|
Antenna input terminal. |
|
8 |
|
|
|
|
|
|
|
qs T |
|
Monitor output terminal. |
|
8 |
|
|
|
|
|
|
|
qd |
|
|
Component video input terminal. |
|
9 |
|
|
|
|
|
|
qf t1 |
|
Video input terminal 1. |
|
8 |
|
|
|
|
|
|
|
7
x Connecting optional components
Connecting to the video input terminal ( t )
TV front panel
2 |
Audio/Video cable |
|
(not supplied) |
||
|
||
|
Camcorder |
L (MONO) R
TV rear panel
|
1 |
|
Y |
|
CB |
(MONO) L |
L (MONO) |
|
CR |
R |
R |
Antenna cable (not supplied)
VCR
Audio/Video cable (not supplied)
DVD Player
Note
•If you connect a VCR to 8 (antenna input), preset the signal output from the VCR to the program number 0 on the TV (see page 17).
Connecting to the monitor output terminal ( T )
TV rear panel
|
1 |
|
Y |
|
CB |
(MONO) L |
L (MONO) |
|
CR |
R |
R |
Audio system
Audio/Video cable
(not supplied)
VCR
8
Connecting to the component video input terminal ( )
TV rear panel
1 |
|
Y |
Component video |
|
cable |
CB |
(not supplied) |
|
|
(MONO) L |
L (MONO) |
CR |
|
R |
R |
DVD player
Audio cable (not supplied)
Notes
•If your DVD player can output interlace and progressive mode signals, select the interlace output when connecting to (component video input) on your TV. Your TV can receive either 525i/60Hz or 625i/50Hz interlace signals.
•The component video terminals on your DVD player are sometimes labeled Y/CB/CR, Y/PB/ PR, Y/Cb/Cr or Y/B-Y/R-Y.
•If you select “DVD” on your TV screen, the signal from the T (monitor output) jacks will not be output properly. This does not indicate a malfunction.
9
xUsing the remote control and basic functions
0
qa qs
qd
qf
qg
qh
qj
qk
ql w;
|
|
|
Button |
|
|
Description |
Page |
|||
|
|
|
1 ?/1 |
|
|
Turn off temporarily or turn on |
– |
|||
|
|
1 |
|
|
|
|
|
the TV. |
|
|
A/B |
|
2 a |
|
|
|
Display the TV program. |
– |
|||
|
|
|
|
|
|
|
|
|
||
|
|
2 |
3 |
|
|
|
|
Jump to last program number |
– |
|
1 |
2 |
3 |
|
|
|
|
|
that has been watched for at |
|
|
4 |
5 |
6 |
|
|
|
|
|
least five seconds. |
|
|
4 PROG +/– |
Select program number. |
– |
||||||||
7 |
|
9 |
||||||||
8 |
5 2 +/– |
Adjust volume. |
– |
|||||||
|
0 |
3 |
8 |
|
|
|
|
Change the picture size: |
– |
|
|
|
PROG |
(KV-SW21M81/ |
“On” (16:9 wide-mode), “Off”. |
|
|||||
|
|
4 |
SW21M80 only) |
|
|
|||||
|
|
5 |
9 |
|
|
|
|
Select surround mode options: |
15 |
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
“On”, “Simulated”, “Off”. |
|
|
|
|
|
0 |
|
|
|
|
Display on-screen information. |
– |
|
|
|
6 |
qa |
|
|
|
|
Mute the sound. |
– |
|
RETURN |
|
WEGA |
qd t |
|
|
|
Select TV or video input. |
8 |
||
|
7 |
|
|
|
||||||
|
GATE |
|
|
|
|
|
|
|
||
|
|
8 |
qf 0 – 9 |
|
Input numbers. For program |
– |
||||
|
|
|
|
|
|
|
numbers 10 and above, enter the |
|
||
|
TV |
9 |
|
|
|
|
|
second digit within two seconds. |
|
|
|
|
ql |
|
|
|
|
Select sound mode options |
15 |
||
|
|
|
|
|
|
|
||||
|
|
|
Dynamic |
|
with a 5-Band Graphic |
|
||||
|
|
|
|
|
|
|
|
Equalizer display: |
|
|
|
|
|
|
|
|
|
|
“Dynamic”, “Standard”, |
|
|
|
|
|
100 |
300 |
1k |
3k |
8k |
“Custom”*. |
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
Standard |
|
* When the “Custom” mode is |
|
||||
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
selected, you can receive the last |
|
|
|
|
|
100 |
300 |
1k |
3k |
8k |
adjusted sound settings from the |
|
|
|
|
|
Custom |
|
“Sound Adjustment” option in |
|
||||
|
|
|
|
the menu. |
|
|||||
|
|
|
|
|
|
|
|
|
||
|
|
|
100 |
300 |
1k |
3k |
8k |
|
|
|
|
|
|
w; |
|
|
|
|
Select picture mode options: |
14 |
|
|
|
|
|
|
|
|
|
“Vivid”, “Standard”, “Custom”*. |
|
|
|
|
|
|
|
|
|
|
* When the “Custom” mode is |
|
|
|
|
|
|
|
|
|
|
selected, you can receive the last |
|
|
|
|
|
|
|
|
|
|
adjusted picture settings from the |
|
|
|
|
|
|
|
|
|
|
“Picture Adjustment” option in |
|
|
|
|
|
|
|
|
|
|
the menu. |
|
10
Button |
|
|
|
|
|
|
Description |
|
Page |
|
WEGA GATE menu operations |
|
|||||||||
6 |
|
|
|
|
|
|
Confirm selected items. |
|
12 |
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|||||
|
7 WEGA GATE |
Display or cancel WEGA GATE menu. |
|
|
||||||
|
|
|
|
|
|
|||||
|
qj V, v, B, b |
Select and adjust items. |
|
|
||||||
|
|
|
|
|
|
|||||
|
qk RETURN |
Return to the previous level. |
|
|
||||||
|
|
|
|
|
||||||
Timer operations |
|
|
|
|||||||
|
qg |
|
|
|
|
|
|
Set TV to turn on automatically according to the |
|
– |
|
|
|
|
|
|
|
|
|||
|
(Wake Up Timer) |
|
desired period of time (max. of 12 hours). |
|
|
|||||
|
|
|
|
|
|
|
|
The indicator on TV lights up amber once you set |
|
|
|
|
|
|
|
|
|
|
the wake up timer. |
|
|
|
|
|
|
|
|
|
|
If no buttons or controls are pressed for more than one |
|
|
|
|
|
|
|
|
|
|
hour after the TV is turned on using the wake up timer, |
|
|
|
|
|
|
|
|
|
|
the TV automatically goes into standby mode. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
qh |
|
|
|
|
|
|
Set TV to turn off automatically according to the |
|
– |
|
(Sleep Timer) |
|
desired period of time (max. of one hour and 30 min.). |
|
|
|||||
|
|
|
|
|
||||||
Teletext operations (green label) |
|
|||||||||
(KV-SW21M81 only) |
|
|
|
|||||||
, |
|
|
|
, |
, |
|
|
|
||
, |
|
|
|
All buttons are used for Teletext operations. |
|
19 |
||||
, |
, |
|
|
, |
, |
|
|
|
|
|
|
(red, green, |
|
|
|
|
|||||
|
yellow, blue) |
|
|
|
|
|||||
|
|
|
|
|
|
|||||
PIP operations |
|
|
|
|
|
|||||
, |
, |
|
, |
|
, , |
|
Not function for your TV. |
|
– |
|
|
|
|
V |
|
v |
B b |
|
|
|
|
Stereo/bilingual operations |
|
|||||||||
|
qs A/B |
|
|
|
|
Not function for your TV. |
|
– |
||
|
|
|
|
|
|
|
|
|
|
|
11
x Introducing the WEGA GATE
navigator
WEGA GATE is a gateway that allows you access to preset TV channels, connected external inputs and “Settings” menu.
WEGA GATE
TV
External Inputs
Settings
Select Confirm
“TV”
“External Inputs”
“Settings”
TV |
|
|
|
|
|
01 |
|
|
|
|
|
02 |
|
|
watch the preset TV |
||
03 |
|
|
|||
04 |
|
|
channels (see page 5) |
||
05 |
|
|
|
|
|
Select |
Confirm |
|
|
|
|
End |
|
|
|
|
|
External Inputs |
|
|
|
||
1 |
Video 1 |
|
select the inputs for the |
||
2 |
Video 2 |
|
|||
|
DVD |
|
connected equipment |
||
|
|
|
(see page 8) |
||
Select |
Confirm |
|
|
||
End |
|
|
|
|
|
|
Picture |
|
|
|
|
Picture Mode: |
Vivid |
|
change the settings |
||
Picture Adjustment |
|
|
|||
Color Temperature: |
Cool |
|
of your TV (see |
||
Intelligent Picture: |
On |
||||
page 13) |
|||||
|
|
|
|
Select |
Confirm |
End |
How to use WEGA GATE
WEGA GATE
TV
External Inputs
Settings
Select Confirm
TV
01 02 03 04 05
Select |
Confirm |
End
(1)Press WEGA GATE to display or cancel the WEGA GATE menu.
TV
01 02 03 04 05
Select |
Confirm |
End
(3) Press V or v to select the desired item.
WEGA GATE
TV
External Inputs
Settings
Select Confirm
(2)Press (or b) to confirm your selection or go to the next level.
Tip
(4)Press RETURN to move to the previous level.
•The WEGA GATE, and V,v,B,b buttons on the top control panel can also be used for the operations above.
12
x “Settings” Adjustment
You are able to change the settings of your TV from “Settings” in WEGA GATE menu.
Press WEGA GATE button to display WEGA GATE menu. Press V or v to select “Settings” and press .
The following is an overview of the items that can be adjusted.
Picture
|
Picture Mode: |
Vivid |
|
Picture Adjustment |
|
|
Color Temperature: |
Cool |
|
Intelligent Picture: |
On |
Select |
Confirm |
End |
|
Sound |
|
|
Sound Mode: |
Dynamic |
|
Sound Adjustment |
|
|
Balance |
|
|
Intelligent Volume: |
Off |
|
Surround: |
Off |
Select |
Confirm |
End |
Channel Setup
Auto Program
Manual Program
Program Sorting/Edit
Select |
Confirm |
End |
”Picture” (see page 14)
“Picture Mode”: “Vivid” “Standard” “Custom”
“Picture Adjustment”: “Picture”, “Brightness”, “Color”, “Hue”, “Sharpness”, “Reset”
“Color Temperature”: “Cool” “Neutral” “Warm” “Intelligent Picture”: “On” “Off”
”Sound” (see page 15)
“Sound Mode”: “Dynamic” “Standard” “Custom” “Sound Adjustment”: “Adjust”, “Reset”
“Balance”
“Intelligent Volume”: “On” “Off” “Surround”: “On” “Simulated” “Off”
”Channel Setup” (see page 16)
“Auto Program” “Manual Program”
“Program”: “00” - “99”
“TV System”: “B/G” “I” “D/K” “M” “VHF Low”/“VHF High”/“UHF”
“Fine”: “Auto” “Manual” “Signal Booster”: “Auto” “Off”
“Program Sorting/Edit”
Setup
|
Language: |
English |
|
Picture Rotation |
|
|
Video Label |
|
|
Color System: |
Auto |
|
Wake Up Timer Beep: On |
|
|
Factory Settings |
|
Select |
Confirm |
End |
Note
”Setup” (see page 18)
“Language”: “English” “” (Arabic) “Picture Rotation” (KV-SW21M81 only) “Video Label”: “Video Input”, “Label”
“Color System”: “Auto” “PAL” “SECAM” “NTSC3.58” “NTSC4.43”
“Wake Up Timer Beep”: “On” “Off” “Factory Settings”: “Yes” “No”
• When a feature is dimmed in the menu, it is not selectable.
13
x Changing the “Picture” setting
The “Picture” menu allows you to adjust the picture settings.
1 |
Press WEGA GATE and select “Settings”. |
|
2 |
Make sure the “Picture” icon ( ) is selected, then press . |
|
3 |
Press V or v to select the desired item (e.g., “Picture Mode”), then press . |
|
|
Select |
To |
|
|
|
|
“Picture Mode” |
choose either “Vivid” (contrast and sharp), “Standard” |
|
|
(normal) or “Custom”*. |
|
|
|
|
“Color Temperature” |
adjust white color tint. |
|
|
Choose either “Cool” (blue tint), “Neutral” (neutral tint) or |
|
|
“Warm” (red tint). |
|
|
|
|
“Intelligent Picture” |
optimize picture quality. |
|
|
Press V or v to select “On”, then press . |
|
|
To cancel, select “Off”, then press . |
|
|
|
*You can adjust the setting to your personal preference in the “Picture Adjustment” and “Color Temperature” options only when the “Custom” mode is selected.
Adjusting the “Picture Adjustment” items under “Custom” mode
1 |
Press V or v to select either “Picture” (contrast), “Brightness”, “Color”, |
|
“Hue” (color tones) or “Sharpness”, then press . |
Selecting “Reset” will set your TV to the factory settings.
2 |
Press V,v,B or b to adjust the setting of your selected item, then press . |
3 |
Repeat the above steps to adjust other items. |
|
The adjusted settings will be received when you select “Custom”. |
Notes
•“Hue” can be adjusted for the NTSC color system only.
•Reducing “Sharpness” can also reduce picture noise.
14
x Changing the “Sound” setting
The “Sound” menu allows you to adjust the sound settings.
1 |
Press WEGA GATE and select “Settings”. |
|
2 |
Press V or v to select the “Sound” icon ( ), then press . |
|
3 |
Press V or v to select the desired item (e.g., “Sound Mode”), then press . |
|
|
Select |
To |
|
|
|
|
“Sound Mode” |
choose either “Dynamic” (low and high tones), “Standard” |
|
|
(voice and high tones) or “Custom”*. |
|
|
|
|
“Balance” |
Press v or B to emphasize the left speaker. |
|
|
Press V or b to emphasize the right speaker. |
|
|
|
|
“Intelligent Volume” |
adjust the volume of all program numbers and video inputs |
|
|
automatically. |
|
|
Press V or v to select “On”, then press . |
|
|
To cancel, select “Off”, then press . |
|
|
|
|
“Surround” |
choose either “On” (surround), “Simulated” (stereo-like |
|
|
monaural sound) or “Off”. |
|
|
|
*You can adjust the setting to your personal preference in the “Sound Adjustment” option only when the “Custom” mode is selected.
Adjusting the “Sound Adjustment” items under “Custom” mode
The 5-Band Graphic Equalizer feature allows you to adjust sound frequency settings of “Custom” mode in the menu.
1 Make sure that “Adjust” is selected, then press .
Selecting “Reset” will set your TV to the factory settings.
2 |
Press B or b to select the desired sound frequency, then press V or v to |
|
adjust the setting and press . |
The adjusted settings will be received when you select “Custom”.
Notes
•Adjusting higher frequency will affect higher pitched sound and adjusting lower frequency will affect lower pitched sound.
•You may display the settings directly using the SOUND MODE button on the top control panel (see page 7) or button on the remote control (see page 10).
15
x Changing the “Channel Setup”
setting
The “Channel Setup” menu allows you to preset channels automatically, manually preset channels and sort or edit the channels.
1 |
Press WEGA GATE and select “Settings”. |
|
2 |
Press V or v to select the “Channel Setup” icon ( ), then press . |
|
3 |
Press V or v to select the desired item (e.g., “Auto Program”), then press . |
|
|
Select |
To |
|
|
|
|
“Auto Program” |
preset channels automatically. |
|
|
|
|
“Manual Program” |
manually preset desired channels and channels that cannot |
|
|
be preset automatically (see Presetting channels manually |
|
|
in page 17). |
|
|
|
|
“Program Sorting/Edit” |
change the order in which the channels appear on the screen, |
|
|
label the program number, skip the program number and |
|
|
block unwanted programs. |
|
|
(see step 3 of the section “Initial Setup” in page 5). |
|
|
|
Notes
•If you preset a blocked program number, that program number will be unblocked automatically.
•If you sort a blocked program, that program will remain blocked.
16
Presetting channels manually
1 |
After selecting “Manual Program”, select the program |
|
|
number to which you want to preset a channel. |
|
|
(1) |
Make sure “Program” is selected, then press . |
|
(2) |
Press V or v until the program number you want |
|
|
to preset appears on the menu, then press . |
01 |
2 Select the desired channel.
(1)Make sure either “VHF Low”, “VHF High” or “UHF” is selected, then press
.
(2)Press V or v until the desired channel’s broadcast appears on the TV screen, then press .
3 |
If the sound of the desired channel is abnormal, select the appropriate TV |
|
|
system. |
|
|
(1) |
Press V or v to select “TV System”, then press . |
|
(2) |
Press V or v until the sound becomes normal, then press . |
|
|
|
4 |
If you are not satisfied with the picture and sound quality, you may be able |
|
|
to improve them by using the “Fine” tuning feature. |
|
|
(1) |
Press V or v to select “Fine”, then press . |
|
(2) |
Press V or v to select “Manual”, then press . |
|
(3) |
Press V,v,B or b until the picture and sound quality are optimal, then press . |
|
|
The + or – icon on the menu flashes while tuning. |
|
|
|
5 |
If the TV signal is too strong (picture distorted; picture with lines; signal |
|
|
interference) or weak (snowy picture), you may be able to improve the |
|
|
picture quality by setting the “Signal Booster” feature. |
|
|
(1) |
Press V or v to select “Signal Booster”, then press . |
|
(2) |
Press V or v to select either “Off” (for picture distorted; picture with lines; |
|
|
signal interference) or “Auto” (for snowy picture), then press . |
|
|
|
17
x Changing the “Setup” setting
The “Setup” menu allows you to change the menu language, adjust the picture position, label the connected equipment, select the color system, set the wake up timer beep and reset your TV to factory settings.
1 |
Press WEGA GATE and select “Settings”. |
2 |
Press V or v to select the “Setup” icon ( ), then press . |
3 |
Press V or v to select the desired item (e.g., “Language”), then press . |
Select |
To |
|
|
|
“Language” |
change the menu language. |
|
||
|
Press V or v to select either “English” or “ |
” (Arabic), then press |
||
|
|
. |
|
|
|
|
|||
“Picture Rotation” |
adjust the picture position when it is not aligned with the TV |
|||
(KV-SW21M81 only) |
screen. |
|
|
|
|
Press B or b to adjust the picture position, then press . |
|||
|
|
|
||
“Video Label” |
label the connected equipment. |
|
||
|
(1) |
Select “Video Input” and press . Press V or v to select the |
||
|
|
input you want to label, then press . |
||
|
(2) |
Select “Label” and press , then press V or v to select |
||
|
|
the label options: “Video 1”/ “Video 2”/ “DVD”, “VCR”, |
||
|
|
“SAT”, “Game” or “Edit”*. |
|
|
|
* You may edit the video label to your favorite name. Press V or v |
|||
|
to select alphanumeric characters for the label, then press . |
|||
|
|
|
||
“Color System” |
select the color system. |
|
||
|
Press V or v to select either “Auto”, “PAL”, “SECAM”, |
|||
|
“NTSC3.58” or “NTSC4.43”, then press |
. Normally, set this to |
||
|
“Auto”. |
|
|
|
|
|
|||
“Wake Up Timer |
allow your TV to emit beeping sound when TV switches on |
|||
Beep” |
automatically using wake up timer. |
|
||
|
Press V or v to select “On”, then press . |
|
||
|
To cancel, select “Off”, then press . |
|
||
|
|
|
||
“Factory Settings” |
reset your TV to factory settings. |
|
||
|
Press |
and press V or v to select “Yes”, then press . |
To cancel, select “No”, then press .
Notes
•To ensure the beeping sound can be heard, you must set an appropriate volume level on your TV and make sure the TV is not in mute condition.
•To stop the beeping sound, press any buttons on the remote control or top control panel.
•If no button is pressed for three minutes, the beeping sound will automatically go off.
18
x Viewing Teletext
B KV-SW21M81 only
Some TV stations broadcast an information service called Teletext which allows you to receive various information, such as stock market reports and news.
You can use the buttons on the remote to view Teletext.
A/B |
|
|
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
9 |
, |
0 |
|
|
PROG |
|
|
|
WEGA |
RETURN |
|
GATE |
(red, |
|
|
green, |
TV |
|
yellow, |
|
|
|
|
|
blue) |
|
|
To |
Do this |
|
|
display a Teletext |
Press |
. Each time you press |
, the |
page on the |
screen changes as follows: |
|
|
TV picture |
Teletext t Teletext and TV t TV. |
||
|
If there is no Teletext broadcast, “100” is |
||
|
displayed at the top left corner of the |
||
|
screen. |
|
|
|
|
|
|
check the contents |
Press . |
|
|
of a Teletext service |
An overview of the Teletext contents, |
||
|
including page numbers, appears on the |
||
|
screen. |
|
|
|
|
||
select a Teletext page |
Press the number buttons to enter the |
||
|
three-digit page number of the desired |
||
|
Teletext page. If you make a mistake, |
||
|
reenter the correct page number. To |
||
|
access the next or previous page, press |
||
|
or . |
|
|
|
|
|
|
hold (pause) a |
Press |
to display the symbol “ |
” at |
Teletext display |
the top left corner of the screen. To |
||
|
resume normal Teletext viewing, press |
||
|
. |
|
|
|
|
|
|
reveal concealed |
Press . |
|
|
information (e.g., |
To conceal the information, press the |
||
an answer to a quiz) |
button again. |
|
|
|
|
|
|
enlarge the Teletext |
Press |
. Each time you press |
, the |
display |
Teletext display changes as follows: |
||
|
Enlarge upper half t Enlarge lower |
||
|
half t Normal size. |
|
|
|
|
|
|
stand by for a Teletext (1) Enter the Teletext page number that
page while watching |
you want to refer to, then press . |
|
a TV program |
(2) When the page number is displayed, |
|
|
press |
to show the text. |
|
|
|
select a FASTEXT |
Press |
(red, green, yellow and blue) |
menu or the colored |
that corresponds to the desired menu or |
|
boxes |
page number. |
|
|
|
|
turn off Teletext |
Press a. |
|
|
|
|
Note
• The FASTEXT feature can be used only when the FASTEXT broadcast is available.
19