Sony KV-AR29M86, KV-AR29M61, KV-AR29N90 Service Manual
REVISION HISTORY
BG3R
CHASSIS
MODEL
KV-AR29M61
KV-AR29M86
KV-AR29N90
NO. SUFFIX DATE SUPPL. / CORR DESCRIPTION
1 -01 2002/10 -- 1st. Issue
PA RT NO. : 9-872-343-01
SERVICE MANUAL BG3R
CHASSIS
MODEL COMMANDER DEST. CHASSIS NO.
KV-AR29M61 RM-995 GE SCC-U52L-A
KV-AR29M86 RM-993 ME SCC-U48W-A
KV-AR29N90 RM-996 Philippines SCC-U65F-A
MODEL COMMANDER DEST. CHASSIS NO.
RM-993
TRINITRON
RM-995
®
RM-996
COLOR TV
KV-AR29M61/AR29M86/AR29N90
RM-995 RM-993 RM-996
Power requirements 110-240 V AC, 50/60Hz
Power consumption (W) Indicated on the rear of the TV
Television system B/G, I, D/K, M
Color system PAL, PAL 60, SECAM, NTSC3.58, NTSC4.43
Stereo/Bilingual System NICAM Stereo/Bilingual B/G, I, A2 Stereo/Bilingual B/G (KV-AR29M61)
Teletext language English, Arabic, French (KV-AR29M61)
English, Farsi (Persian), French (KV-AR29M86)
Channel coverage
B/G VHF: E2 to E12 / UHF: E21 to E69
CATV: S01 to S03, S1 to S41
I UHF: B21 to B68 / CATV: S01 to S03, S1 to S41
D/K VHF: C1 to C12, R1 to R12
UHF: C13 to C57, R21 to R60
CATV: S01 to S03, S1 to S41, Z1 to Z39
M VHF: A2 to A13 / UHF: A14 to A79
CATV: A-8 to A-2, A to W+4, W+6 to W+84
˘(Antenna) 75-ohm external terminal
Audio output (Speaker) 8W + 8W
Number of terminal
DVideo Input: 4* Output: 1 * Three input lines available Phono jacks; 1 Vp-p, 75 ohms
≥ (Audio) Input: 4* Output: 1 * Three input lines available Phono jacks; 500 mVrms
(S Video) Input : 2 Y: 1 Vp-p, 75 ohms
(Component Input : 1 Phono jacks:
Video) Y: 1 Vp-p, 75 ohms
2 (Headphone) Output: 1 Stereo minijack
Picture tube 29 in
Tube size (cm) 72 measured diagonally
Screen size (cm) 68 measured diagonally
Dimension (w/h/d,mm) 765 × 578 × 502
Mass (kg) 49
SPECIFICATIONS
(KV-AR29M61/AR29M86)
Note
unbalanced, sync negative
C: 0.286 Vp-p, 75 ohms
sync negative
B: 0.7 Vp-p, 75 ohms
C
R: 0.7 Vp-p, 75 ohms
C
Audio: 500mVrms
CAUTION
SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND
THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR
CARBON PAINTED ON THE CRT, AFTER REMOVING THE
ANODE.
Design and specifications are subject to change without notice.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY SHADING AND MARK ! ON
THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE
PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE
THESE COMPONENTS WITH SONY PARTS WHOSE PART
NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
– 2 –
KV-AR29M61/AR29M86/AR29N90
RM-995 RM-993 RM-996
SPECIFICATIONS
(KV-AR29N90)
Note
Power requirements 110-240 V AC, 50/60Hz
Power consumption (W) Indicated on the rear of the TV
Television system M
Color system NTSC3.58, PAL*, PAL 60*, SECAM*, NTSC4.43* *AV IN only
Stereo/Bilingual System MTS
Channel coverage VHF: 2 to 13
UHF: 14 to 69
CATV: 1 to 125
˘(Antenna) 75-ohm external terminal
Audio output (Speaker) 8W + 8W
Number of terminal
Video Input: 4* Output: 1 * Three input lines available Phono jacks; 1 Vp-p, 75 ohms
(Audio) Input: 4* Output: 1 * Three input lines available Phono jacks; 500 mVrms
(S Video) Input : 2 Y: 1 Vp-p, 75 ohms
unbalanced, sync negative
C: 0.286 Vp-p, 75 ohms
(Component Input : 1 Phono jacks:
Video (DVD) IN) Y: 1 Vp-p, 75 ohms
sync negative
B: 0.7 Vp-p, 75 ohms
C
R: 0.7 Vp-p, 75 ohms
C
Audio: 500mVrms
2 (Headphone) Output: 1 Stereo minijack
Picture tube 29 in
Tube size (cm) 72 measured diagonally
Screen size (cm) 68 measured diagonally
Dimension (w/h/d,mm) 765 × 578 × 502
Mass (kg) 49 kg
CAUTION
SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND
THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR
CARBON PAINTED ON THE CRT, AFTER REMOVING THE
ANODE.
Design and specifications are subject to change without notice.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY SHADING AND MARK ! ON
THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE
PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE
THESE COMPONENTS WITH SONY PARTS WHOSE PART
NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
– 3 –
KV-AR29M61/AR29M86/AR29N90
RM-995 RM-993 RM-996
TABLE OF CONTENTS
Section Title Page
SELF DIAGNOSTIC FUNCTION ........................................ 5
1. DISASSEMBLY
1-1. Rear Cover Removal ................................................... 8
1-2. Speaker Removal ........................................................ 8
1-3. Chassis Assy Removal (KV-AR29M61/AR29N90) .. 8
1-4. Chassis Assy Removal (KV-AR29M86) .................... 8
1-5. Service Position .......................................................... 8
1-6. F Board Removal (KV-AR29M61/AR29N90) .......... 8
1-7. F Board Removal (KV-AR29M86) ............................ 9
1-8. Terminal Bracket and J Board Removal
(KV-AR29M61/AR29N90) ........................................ 9
1-9. Terminal Bracket and J Board Removal
(KV-AR29M86) .......................................................... 9
1-10. B1 and V1 Boards Removal ....................................... 9
1-11. P5 and V1 Boards Removal ........................................ 9
1-12. D3 Board Removal ..................................................... 9
1-13. H1 and H2 Boards Removal ..................................... 10
1-14. A and B10 Boards Removal ..................................... 10
1-15. A and B8 Boards Removal ....................................... 10
1-16. Picture Tube Removal............................................... 11
2. ADVANCE OPERATION
2-1. "RESET" Function .................................................... 12
Section Title Page
5. DIAGRAMS
5-1. Block Diagram .......................................................... 34
5-2. Circuit Boards Location ........................................... 38
5-3. Schematic Diagram ................................................... 39
(1) A Board Schematic Diagram .............................. 40
(2) B10 Board Schematic Diagram .......................... 44
(3) V1 Board Schematic Diagram ............................ 46
(4) C6 Board Schematic Diagram ............................ 48
(5) H1 Board Schematic Diagram ............................ 50
(6) B8 Board Schematic Diagram ............................ 52
(7) P5 Board Schematic Diagram............................. 54
(8) J and F Boards Schematic Diagrams .................. 62
(9) H2 Board Schematic Diagram ............................ 63
(10) B1 Board Schematic Diagram .......................... 64
(11) D3 Board Schematic Diagram .......................... 65
(12) VM1 Board Schematic Diagram ...................... 66
5-4. Voltage List and Waveforms ..................................... 69
5-5. Printed Wiring Boards and Parts Location............... 78
5-6. Semiconductors ......................................................... 90
6. EXPLODED VIEWS
6-1. Speaker Bracket ........................................................ 93
6-2. Chassis ...................................................................... 94
6-3. Picture Tube .............................................................. 96
3. SET-UP ADJUSTMENTS
3-1. Beam Landing ........................................................... 13
3-2. Convergence .............................................................. 14
3-3. Focus Adjustment ..................................................... 16
3-4. G2 (SCREEN) and White Balance Adjustment ....... 17
4. CIRCUIT ADJUSTMENTS
4-1. Adjustment With Commander .................................. 18
4-2. Adjustment Method .................................................. 18
4-3. Adjustment for Non Digital Texture Enchancer
(DTE) Model ............................................................. 30
4-4. Adjustment for Digital Texture Enchancer
(DTE) Model ............................................................. 30
4-5. Display Position Adjustment .................................... 31
4-6. Deflection Adjustment .............................................. 31
4-7. H-Trapezoid Adjustment .......................................... 32
4-8. A Board Adjustment After IC003
(Memory) Replacement ............................................ 32
4-9. Picture Distortion Adjustment (1) ............................ 33
7. ELECTRICAL PARTS LIST ......................................... 98
OPERATING INSTRUCTIONS
– 4 –
KV-AR29M61/AR29M86/AR29N90
RM-995 RM-993 RM-996
SELF DIAGNOSIS FUNCTION
The units in this manual contain a self-diagnosis function. If an error occurs, the STANDBY (1) indicator will automatically
begin to flash. A description of the self diagnosis function is explained in the instruction manual.
The number of times the STANDBY (1) indicator flashes translates to a probable source of the problem. If an error
symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in
memory to reveal past problems and how often these problems occur.
1. DIAGNOSIS TEST INDICATORS
When an errors occurs, the STANDBY (1) indicator will flash a set number of times to indicate the possible cause of the
problem. If there is more than one error, the indicator will identify the first of the problem areas.
Result for all of the following diagnosis items are displayed on screen. No error has occured if the screen displays a “0”.
Diagnosis
Item
Description
• Power does not
turn on
• +B overcurrent
(OCP) or
overvoltage
(OVP)
• Vertical deflection
stopped
• Horizontal
deflection
overdrive
• White balance
failure (no
PICTURE)
No. of times
STANDBY (1)
indicator flashes
Does not light
2 times
5 times
Self-diagnostic
display/Diagnosis
result
—
002:000 or
002:001~255
003:001~255
004:001~255
at the same time
005:000 or
005:001~225
Probable
Cause
Location
• Power cord is not plugged
in.
• Fuse is burned out F4601
(F)
• H.OUT Q511 is shorted.
(A board)
• Q701, Q702, Q703 is
shorted (C6 board)
• -13V is not supplied.
(A board)
• IC 503 faulty (A board)
• G2 is improperly adjusted.
(Note 2)
• CRT problem.
• R(Q703), G(Q702) or
B(Q701) out is faulty
(C6 board)
• IC301 is faulty. (A board)
• No connection A board to
C6 board.
Detected
Symptoms
• Power does not come on.
• No power is supplied to the
TV.
• AC power supply is faulty.
• Power does not come on.
• Load on power line is
shorted.
• Has entered standby state
after horizontal raster.
• Vertical deflection pulse is
stopped.
• Power line is shorted or
power supply is stopped.
• No raster is generated.
• CRT cathode current
detection reference pulse
output is small.
• Micro reset
Note 1: If a + B overcurrent is detected, stoppage of the vertical deflection is detected simultaneously.
The symptom that is diagnosed first by the microcontroller is displayed on the screen.
Note 2: Refer to screen (G2) Adjustment in section 3-4 of this manual.
* R(Q703), G(Q702) or B(Q701) out is faulty (C6 board).
—
101:00 or
101:001~225
• Discharge CRT (C6 Board)
• Static discharge
• External noise
• Power is shut down shortly,
after this return back to
normal.
• Detect Micro latch up.
– 5 –
KV-AR29M61/AR29M86/AR29N90
RM-995 RM-993 RM-996
2. DISPLAY OF STANDBY (1) INDICATOR LIGHT
FLASH COUNT
2 times
5 times
Lamp ON 0.3 sec.
Lamp OFF 0.3 sec.
Lamp OFF 3 sec.
3. STOPPING THE STANDBY (1) INDICATOR FLASH
Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY (1) indicator
from flashing.
Diagnosis Item Flash Count*
+B overcurrent/overvoltage 2 times
Vertical deflection stopped
White balance failure 5 times
* One flash count is not used for self-diagnosis.
STANDBY (1) indicator
4. SELF-DIAGNOSTIC SCREEN DIPLAY
For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed,
it is possible to bring up past occurances of failure for confirmation on the screen:
[To Bring Up Screen Test]
In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:
[Screendisplay] / channel [5] / Sound volume [-] / Power ON
˘
Note that this differs from entering the service mode (volume [+]).
Self-Diagnostic screen display
SELF DIAGNOSTIC
002 : 000
003 : 000
004 : 000
005 : 001
101 : 000
Numeral "0" means that no fault has been detected.
Numeral "1" means a fault has been detected.
– 6 –
KV-AR29M61/AR29M86/AR29N90
RM-995 RM-993 RM-996
5. HANDLING OF SELF-DIAGNOSTIC SCREEN DISPLAY
Since the diagnosis results displayed on the screen are not automatically cleared, always check the self-diagnostic screen
during repairs. When you have completed the repairs, clear the result display to “0”.
Unless the result display is cleared to “0”, the self-diagnosis function will not be able to detect subsequent faults after
completion of the repairs.
[Clearing the result display]
To clear the result display to “0”, press buttons on the remote commander sequentially as shown below when the selfdiagnostic screen is being displayed.
Channel [8] / 0
[Quitting Self-diagnostic screen]
To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.
6. SELF-DIANOSIS CIRCUIT
FROM
CRT
FROM
[+B] Q604 C6
[V] Q509/507
IC301
Y/CHROMA JUNGLE
IK-IN
MP/
18
PROTECT
35
SDA
IC001
SYSTEM
IO-8DAT B-DAT
O-LED
46
IO-SDAT
45
51
IC003
MEMORY
521
[+BovercurrentªOCPº] Occurs when an overcurrent on the +B(135) line is detected by Q604. If Q604 go to ON
and the voltage to pin 18 of IC301 should go down when V.SYNC is more than seven
verticals in a period, the unit will automatically turn off.
[Verticaldeflectionstopped] Occurs when an absence of the vertical deflection pulse is detected by Q509 and IC001
shut down the power supply.
[Verticaldeflectionovercurrent] Occurs when an overcurrent on V drive line is detected by Q507. Power supply will be
shut down when detect this by IC001.
[Whitebalancefailure] If the RGB levels* do not balance or become low level within 5 seconds, this error will be
detected by IC301. TV will stay on, but there will be no picture.
* (Refers to the RGB levels of the AKB detection Ref pulse that detects IK.)
– 7 –
KV-AR29M61/AR29M86/AR29N90
RM-995 RM-993 RM-996
SECTION 1
DISASSEMBLY
1-1. REAR COVER REMOVAL
2 Rear cover
1-3. CHASSIS ASSY REMOVAL
(KV-AR29M61/AR29N90)
1 Nine screws
(+BVTP 4 × 16)
1-2. SPEAKER REMOVAL
1 Two screws
(+BVTP 4 × 16)
2 Two screws
(Washer Head) (+P4x16)
3 Two screws
(+BVTP 4 × 16)
1-4. CHASSIS ASSY REMOVAL
(KV-AR29M86)
1-5. SERVICE POSITION
1-6. F BOARD REMOVAL
(KV-AR29M61/AR29N90)
– 8 –
1 Two screw
(+BVTP 3x12)
4 F Board
2 Bracket F PWB
3 Two hooks
KV-AR29M61/AR29M86/AR29N90
RM-995 RM-993 RM-996
1-7. F BOARD REMOVAL (KV-AR29M86)
1 Two screw
(+BVTP 3x12)
2 Bracket F PWB
3 Two hooks
4 F Board
1-9. TERMINAL BRACKET AND J BOARD
REMOVAL (KV-AR29M86)
1-8. TERMINAL BRACKET AND J BOARD
REMOVAL (KV-AR29M61/AR29N90)
6 J Board
1 One screw
(+BVTP 3 × 12)
4 Terminal bracket
1 One screw
(+BVTP 3 × 12)
2 Two Hooks
5 Two screws
(+BVTP 3 × 12)
3 One screw
(+BVTP 4 × 16)
1-10. B1 BOARD
6 J Board
1 One screw
(+BVTP 3 × 12)
4 Terminal
1 One screw
(+BVTP 3 × 12)
2 Two Hooks
3 One screw
(+BVTP 4 × 16)
bracket
5 Two screws
(+BVTP 3 × 12)
1-11. P5 AND V1 BOARDS REMOVAL
1 P5 Board (KV-AR29M86)
2 B1 Board
(KV-AR29M61/
AR29N90)
1 One connector
1-12. D3 BOARD REMOVAL
2 V1 Board
(KV-AR29M61/
AR29M86)
– 9 –
1 One Hooks
2 D3 Board
KV-AR29M61/AR29M86/AR29N90
RM-995 RM-993 RM-996
1-13. H1 AND H2 BOARDS REMOVAL
2 Two screws
(Washer head)
(+BVTP 3x12)
6 H2 Board
5 Cover, H
4 Two hooks
3 Four hooks
1 H1 Board
1-15. A AND B8 BOARDS REMOVAL
(KV-AR29M86)
1 Three screws
5 One screw
(3 × 12)(+) BVTP
(3 × 12)(+) BVTP
2Two hooks
3 Four
connectors
1-14. A AND B10 BOARDS REMOVAL
(KV-AR29M61/AR29N90)
1 Three screws (Washer head)
5 One screw
(Washer head)
(3 × 12)(+)(BVTP)
2 Three
connectors
7 Four hooks
(3 × 12)(+) BVTP
8 A Board
3 Three hooks
6 One screw
(Washer head)
(3 × 12)(+)(BVTAP)
4 B10 Board
6 Four hooks
4 B8 Board
7 A Board
– 10 –
KV-AR29M61/AR29M86/AR29N90
c
RM-995 RM-993 RM-996
1-16. PICTURE TUBE REMOVAL
Note:
• Please make sure the TV set is not in standing position before removing necessary CRT support located on bottom
right and left.
1) Place the TV set with the CRT face down on a cushion jig.
2) Removal the rear cover.
1 Anode Cap Removal
qa Earth Coating Assy
qs Nut, locking
8 Holder, DGC(2)
Removal
q; Spring Tension(2)
Removal
5 Loosen the Neck Assembly
fixing screw and removal
4 VM1 Board Removal
7 Band, DGC Removal
9 Degaussing Coil
3 Loosen the Neck Assembly
fixing screw and removal
2 C6 Board Removal
6 Chassis Assy Removal
• REMOVAL OF ANODE-CAP
Note:
• After removing the anode, short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT
shield or carbon paint on the CRT.
• REMOVING PROCEDURES
a
a
1 Turn up one side of the rubber cap in the direction
indicated by the arrow a.
b
b
2 Using a thumb pull up the rubber cap firmly in the direc-
tion indicated by the arrow b.
anode button
3 When one side of the rubber cap is separated from the
anode button, the anode-cap can be removed by
turning up the rubber cap and pulling it up in the
direction of the arrow c.
• HOW TO HANDLE AN ANODE-CAP
1 Do not damage the surface of anode-caps with
sharp shaped objects.
2 Do not press the rubber too hard so as not to
damage the inside of anode-cap.
A metal fitting called the shatter-hook terminal is
built into the rubber.
3 Do not turn the foot of rubber over too hard.
The shatter-hook terminal will stick out or damage
the rubber.
– 11 –
KV-AR29M61/AR29M86/AR29N90
RM-995 RM-993 RM-996
SECTION 2
ADVANCE OPERATION
2-1. "RESET" FUNCTION
1. Purpose
If a customer faces some setting problem that cannot be solved, using the "RESET" function some items will
be reset to its original setting (shipment condition)
2. How to Operate
The way to access to the "RESET" Function:-
a) By pressing "MENU" button or "SELECT" button (for non-menu models) on the Front Key Input and
hold it down for 5 seconds.
3. Subsequent of Operation
Sequential to the resetting operation (either methods being used in No. 2), TV set would shut down once and
automatically turn on again. The power-off duration is expected to be about 500msec. An OSD message,
"RESET" tentatively will be displayed for 10 sec after IK status gets stable.
As a result, some items will be reset to an initial condition (shipment condition) wheareas some other remains
at the last selection by user.
Items that remains at the last selection by user
Channel No., Favourite CH Setup,
PIC rotation, OSD Language, Fine tuning, TV System, Skip
Reset Items
Video input RF
Volume 30
Picture mode DYNAMIC
DTE ON
Sound mode DYNAMIC
Surround mode OFF
Multi Picture (PIP) OFF
PIP position Bottom Right (KV-AR29M86)
OSD recall OFF
Antenna sensitivity HIGH* (KV-AR29M86)
MTS* (NTSC) STEREO (KV-AR29N90)
*= only when in RF mode
Stereo mode STEREO/NICAM*
Bilingual mode MAIN* (except KV-AR29M86)
High-deviation mode AUTO (except KV-AR29M86)
Child lock OFF*
Wide mode OFF
Game mode OFF
Sleep timer OFF
Wake-up timer OFF
Sound muting OFF
Teletext OFF (except KV-AR29N90)
(except KV-AR29M86)
– 12 –
SECTION 3
SET-UP ADJUSTMENTS
KV-AR29M61/AR29M86/AR29N90
RM-995 RM-993 RM-996
• The following adjustments should be made when a complete
realignment is required or a new picture tube is installed.
• These adjustments should be performed with rated power
supply voltage unless otherwise noted.
Perform the adjustments in the following order :
1. Beam Landing
2. Convergence
3. Focus
4. White Balance
Controls and switches should be set as follows unless otherwise noted:
PICTURE control ........................................................... normal
BRIGHTNESS control ................................................... normal
Note : Test Equipment Required.
1. Pattern Generator
2. Degausser
3. Oscilloscope
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Preparation :
• In order to reduce the influence of geomagnetism on the set's
Purity control
picture tube, face it east or west.
• Switch on the set's power and degauss with the degausser.
3-1. BEAM LANDING
1. Input a white signal with the pattern generator.
Contrast
Brightness
2. Position neck assy as shown in Fig3-2.
}
normal
Fig. 3-3
3. Set the pattern generator raster signal to a green raster.
4. Move the deflection yoke to the rear and adjust with the
purity control so that the green is at the center and the blue
and the red take up equally sized areas on each side.
(See Figures 3-1 through 3-4.)
5. Move the deflection yoke forward and adjust so that the
Blue
Red
Green
entire screen is green. (See Figure 3-2.)
6. Switch the raster signal to blue, then to red and verify the
condition.
7. When the position of the deflection yoke has been decided,
Fig. 3-4
fasten the deflection yoke with the screws and DY spacers.
8. If the beam does not land correctly in all the corners, use a
magnet to adjust it.
(See Figure 3-5.)
Purity control
corrects this area.
b
a
Disk magnets or rotatable
disk magnets correct these
areas (a-d).
Neck assy
Align the edge of
the neck assy with
the edge of the G2 grid.
G2G1 G3
Fig. 3-1
Fig. 3-2
– 13 –
c
Deflection yoke positioning
corrects these areas.
a
d
d
Fig. 3-5
b
c
KV-AR29M61/AR29M86/AR29N90
RM-995 RM-993 RM-996
3-2. CONVERGENCE
Preparation :
• Before starting this adjustment, adjust the focus, horizontal size
and vertical size.
• Receive dot/hatch signal.
• Pic mode: Personal (Pic 90%, Brightness 50%, Colour 50 %,
Hue 50%, Sharpness 50%).
(1) Horizontal and Vertical Static Convergence
Purity
BMC
BMC (Hexapole)
Purity
Center dot
R G B
H. STAT VR
R
G
B
V. STST
Magnet
RV702
H. STAT
RV701
SCREEN (G2)
C6 Board
1. (Moving horizontally), adjust the H.STAT control so that the
red, green and blue dots are on top of each other at the center of
the screen.
2. (Moving vertically), adjust the V.STAT magnet so that the red,
green and blue dots are on top of each other at the center of the
screen.
3. If the H.STAT variable resistor cannot bring the red, green and
blue dots together at the center of the screen, adjust the
horizontal convergence with the H.STAT variable resistor and
the V.STAT magnet in the manner given below.
(In this case, the H.STAT variable resistor and the V.STAT
magnet influence each other, so be sure to perform adjustments
while tracking.)
DY pocket
V.STAT
1 V. STAT
b b
2 H. STAT VR
RGGBB
3
V.STAT
a
a
B
G
R
a
b
R
a
b
B
G
R
b
– 14 –
b
a
R
G
b
B
B
G
R
4 BMC (Hexapole) Magnet.
Neck assy Neck assy
Blue
Red Blue
Red
VM1 board VM1 board
If the red, green and blue dots are not balanced or aligned, then
use the BMC magnet to adjust in the manner described below.
RG B R G B R GB
KV-AR29M61/AR29M86/AR29N90
RM-995 RM-993 RM-996
RB
G
RG
GB
RB
5 Y separation axis correction magnet adjustment.
1. Receive the cross-hatch signal and adjust [PICTURE] to [MIN]
and [BRIGHTNESS] to [STANDARD] .
2. Adjust the Y separation axis correction magnet on the neck
assembly so that the horizontal lines at the top and bottom of
the screen are straight.
(2) Dynamic Convergence Adjustment
Preparation:
• Before starting this adjustment, adjust the horizontal static
convergence and the vertical static convergence
RB
Note
1. The Red and Blue magnets should be equally far from the
horizontal center line.
2. Do not separate the Red and Blue magnets too far. (Less than
8 mm)
B
R
TLH TLV
RB
YCH XCV
R
B
– 15 –
KV-AR29M61/AR29M86/AR29N90
RM-995 RM-993 RM-996
TLV Rotate TLV-2 VOL (29”, 34”) on DY
XCV Rotate XCV Adj core on DY
YCH Rotate YCH VOL on DY
TLH Insert TLH Correction Plate to DY Pocket
(Left or Right)
ON DY:
YCH
TLV1
XCV
TLV2
(3) Screen-corner Convergence
ba
a-d : screen-corner
misconvergence
cd
3-3. FOCUS ADJUSTMENT
FOCUS adjustment should be completed before W/B adjustment.
Focus
Screen
FLYBACK TRANSFORMER (T503)
1. Receive digital monoscope pattern.
2. Set "Picture Mode" to "Standard".
3. Set S2801 to mechanical center position.
4. Adjust focus VR so that the center of the screen becomes just
focus.
5. Adjust S2801 when corner focus is unbalance is right and left.
6. Change the receiving signal to white pattern blue back.
7. Confirm Magenta ring is not noticable. Incase magneta ring is
obvious, reset S2801 to mechanical center position and then
adjust FOCUS VR to balance between MAGENTA RING and
FOCUS.
Fix a Permalloy assy corresponding to the misconverged
areas.
a
d
Permalloy assembly
b
c
– 16 –
KV-AR29M61/AR29M86/AR29N90
RM-995 RM-993 RM-996
3-4. G2 (SCREEN) AND WHITE BALANCE
ADJUSTMENTS
1. G2 (SCREEN) ADJUSTMENT
1) Set the PICTURE to normal.
2) Put to VIDEO input mode without signals.
3) Connect R, G and B of the C6 board cathode to the
oscilloscope.
4) Adjust BRIGHTNESS to obtain the cathode voltage to the
value below.
5) Adjust G2 (screen) on the FBT until picture shows the point
before cut off.
Cathode setting voltage:
175 V ± 2 (VDC)
0 V
2. WHITE BALANCE ADJUSTMENT
1) Set to Service Mode (Refer Section 4-1: ADJUSTMENTS
WITH COMMANDER).
2) Input white raster signal.
3) Set the PICTURE to minimum.
4) Select GCT (WHB 4) and BCT (WHB 5) with [1] and [4], and
adjust the level with [3] and [6] for the best white balance.
5) Set the PICTURE to maximum.
6) Select GDR (WHB 1) and BDR (WHB 2) with [1] and [4],
and adjust the level with [3] and [6] for the best white
balance.
7) Write into the memory by pressing [MUTING] then [0].
3. SUB BRIGHT ADJUSTMENT
1) Set to service mode.
2) Input a staircase signal of black to white from the pattern
generator.
3) BRIGHTNESS ....50%.
PICTURE ............MINIMUM
4) Select SBR (WHB7) with [1] and [4], and adjust SBR
(WHB7) level with [3] and [6] so that the second stripe from
the right is dimly lit.
White
second from the right
Black
– 17 –
KV-AR29M61/AR29M86/AR29N90
RM-995 RM-993 RM-996
4-1. ADJUSTMENTS WITH COMMANDER
Service adjustments to this models can be performed using the
supplied Remote Commander RM-993, RM-995 and RM-996.
a. ENTERING SERVICE MODE
With the unit on standby
n
[DISPLAY] n 5 n VOL (+) n [POWER]
This operation sequence puts the unit into service mode.
The screen display is :
Device
Name
(KV-AR29N90)
605S
(KV-AR29M61
/AR29M86)
Suffix No
(OEM Code)
Software version Total Power-On time (hours)
Item No
00
0.2N
1.1M
Item
Name
Data Mode
HPS 1C SERVICE 50pGEO
59 7F 000A0604S
Marking of new NVM
PAL,SECAM:50
NTSC :60
SECTION 4
CIRCUIT ADJUSTMENTS
7, - All the data becomes the values in memory.
8, - All user control goes to the standard state.
5, - Service data initialization (Be sure not to use
usually.)
[MUTING]+ - Write 50Hz adjustment data to 60Hz, or vice
versa.
2, - Copy and write all data.
4-2. ADJUSTMENT METHOD
Item Number 00 of device GEO
This explanation uses H-Position as an example.
1. Select “GEO 00 HPS” with the 1 and 4 buttons.
2. Raise/lower the data with the 3 and 6 buttons.
3. Select the optimum state. (The standard is 1F for PAL
reception.)
4. Write with the [MUTING] button. (The display changes to
WRITE.)
5. Execute the writing with the - button. (The WRITE
display will be changed to red color while excuting, and
back to SERVICE.)
Example on screen display :-
b. METHOD OF CANCELLATION FROM SERVICE
MODE
Set the standby condition (Press [POWER] button on the commander),
then press [POWER] button again, hereupon it becomes TV mode.
c. METHOD OF WRITE INTO MEMORY
1) Set to Service Mode.
2) Press [1] (UP) and [4] (DOWN), to select the adjustment.
4) Press [MUTING] button to indicate WRITE on the screen.
5) Press [0] button to write into memory.
d. MEMORY WRITE CONFIRMATION METHOD
1) After adjustment, pull out the plug from AC outlet, and then
plug into AC outlet again.
2) Turn the power switch ON and set to Service Mode.
3) Call the adjusted items again to confirm adjustments were made.
1, 4 Select the adjustment item.
↓
3, 6 Raise/lower the data value.
↓
[MUTING] Writes.
↓
- Executes the writing.
GEO 00
0.2N
604S
(KV-AR29N90)
1.1M
605S
(KV-AR29M61/AR29M86)
GEO 00
0.2N
604S
(KV-AR29N90)
1.1M
605S
(KV-AR29M61/AR29M86)
Write with [MUTING]
GEO 00
0.2N
604S
(KV-AR29N90)
1.1M
605S
(KV-AR29M61/AR29M86)
Write executed with -
1F 50HPS
SERVICE
7F 0 000A59
1F WRITE
7F 0 000A59
WRITE
1F 50HPS
7F 0 000A59
GREEN
Adjusted with 3
and 6 buttons.
50HPS
GREEN
RED
The WRITE display
then the display
returns to green
SERVICE.
Use the same method for all Items. Use 1 and 4 to select the
adjustment item, use 3 and 6 to adjust, write with [MUTING],
then execute the write with -.
Note : 1. In [WRITE], the data for all items are written into
memory together.
2. For adjustment items that have different standard data
between 50Hz or 60Hz, be sure to use the respective
input signal after adjustment.
– 18 –
Adjustment Item Table (KV-AR29M61/AR29M86)
GVTytilanoitcnuF
noitcnuFetoN&elbaTemaNeciveD
)deliateD(eulaVlaitinI
yrogetaCoNemaN nommoCCN05CN06CV05CV06wsbtfoS
OEG00SPHnoitisoPH )06/05(ediW/)06/05(lamroNS9512AXC
21A021A0
10ZSHeziSH )06/05(ediW/)06/05(lamroN
52525252
20PAPpmAniP )06/05(ediW/)06/05(lamroN
F1F1F1F1
30TLTmuizeparT )06/05(ediW/)06/05(lamroN
70707070
40SPVnoitisoPV )06/05(ediW/)06/05(lamroN
F1F1F1F1
50ZSVeziSV )06/05(ediW/)06/05(lamroN
F0F07070
60OCSnoitcerroCS )06/05(ediW/)06/05(lamroN
70707070
70NLVytiraeniLV )06/05(ediW/)06/05(lamroN
70707070
80WOBwoBCFA )06/05(ediW/)06/05(lamroN
70707070
90LGAelgnACFA )06/05(ediW/)06/05(lamroN
70707070
A0NPUniPreppU )06/05(ediW/)06/05(lamroN
F1F1F1F1
B0NPLniPrewoL )06/05(ediW/)06/05(lamroN
F1F1F1F1
C0
LBHffo/nogniknalBH
10101010
D0
LBLgniknalBHtfeL )06/05(ediW/)06/05(lamroN
A0F0A0F0
E0
LBRgniknalBHthgiR )06/05(ediW/)06/05(lamroN
20202020
GVTytilanoitcnuF
noitcnuFetoN&elbaTemaNeciveD
)deliateD(eulaVlaitinI
yrogetaCoNemaN nommoCMACESsrehtOcimanyDsrehtO
BHW00
RDRevirDR srehto/CIMANYDS9512AXC
52A2
10RDGevirDG srehto/CIMANYD 5252
20RDBevirDB srehto/CIMANYD
5252
30
TCRffotuCR srehto/MACES
7070
40TCGffotuCG srehto/MACES
7070
50TCBffotuCB srehto/MACES
7070
60
NMBataDmuminiMssenthgirB 51
70RBSlortnoCssenthgirBbuS 52
80
BPA3#erutciPtnegilletnIrofhctiwSlortnoCthgirBbuS 30
)09N/16M92RA-VK(
80
BPA3#erutciPtnegilletnIrofhctiwSlortnoCthgirBbuS 00
)68M92RA-VK(
– 19 –
KV-AR29M61/AR29M86/AR29N90
RM-995 RM-993 RM-996
KV-AR29M61/AR29M86/AR29N90
GVTytilanoitcnuF
noitcnuFetoN&elbaTemaNeciveD
)deliateD(eulaVlaitinI
yrogetaCoNemaN CNCVCNCSTNCNSREHTOCVCSTNCVSREHTOVToediV
JAS00
XMPataDmumixaMerutciP ediW/ediW-nonS9512AXC
63
13
09N/16M92RA-VK()
00
XMPataDmumixaMerutciP ediW/ediW-nonS9512AXC
83
33
68M92RA-VK()
10UHSlortnoCeuHbuS oediV/VT
7070
20
HSSlortnoCssenprahSbuS ediW/VT
40
90 09N/16M92RA-VK()
20
HSSlortnoCssenprahSbuS ediW/VT
40
A0 68M92RA-VK()
30LCSlortnoCroloCbuS )srehto/CSTN(EDIW/)srehto/CSTN(
321202E1
GVTytilanoitcnuF
noitcnuFetoN&elbaTemaNeciveD
)deliateD(eulaVlaitinI
yrogetaCoNemaN nommoCCN05CN06CV05CV06DTS-NONCSTNDTS-NONSREHTODTSCSTNDTSSREHTO
PV00
THEpmoCTHE )06/05(ediW/)06/05(lamroNS9512AXC
50505050
10
AMG)edomDRADNATSnidetarapes(noitcerroCammaG )srehto/CSTN(.DTS/)srehto/CSTN(.DTS-NON
20201010
20GPA3#erutciPtnegilletnIrofhctiwSlortnoCammaG )srehto/CSTN(.DTS/)srehto/CSTN(.DTS-NON
00000000
GVTytilanoitcnuF
noitcnuFetoN&elbaT
)deliateD(eulaVlaitinI
yrogetaCoNemaN nommoCMACESCSTNLAPDVDTXET
PV30
LDYyaleDY DVD/CSTN/MACES/LAP
90806080
)09N/16M92RA-VK(
30
LDYyaleDY DVD/CSTN/MACES/LAP
00000000
)68M92RA-VK(
40
TSSnoitisoPtratSDIMACES CSTN&LAP-DECROF/OTUTA&MACES
10
10
50
PSSnoitisoPpotSDIMACES CSTN&LAP-DECROF/OTUTA&MACES
10
10
60
MLRtimiLBGR 00
70
VLSleveLDIMACES CSTN&LAP-DECROF/OTUTA&MACES
20
20
80FBSrofLLEBMACES CSTN&LAP-DECROF/OTUTA&MACES
22
22
RM-995 RM-993 RM-996
– 20 –
– 21 –
GVTytilanoitcnuF
noitcnuFetoN&elbaT
)deliateD(eulaVlaitinI
yrogetaCoNemaN nommoCCSTNsrehtOVToediVTXET
PV90
CYDffo/noroloCcimanyD 10
A0
LBA)edomDRADNATStpecxe(gnihctiwSedoMLBA DRADNATStpecxe10
B0
HTVgnihctiwShtVnoitceteDLBA 10
C0
0FSssenprahSrofgnihctiwSOF srehto/CSTN
1010
D0
XCDgnihctiwSoitaR.snarTCD 10
E0
THShctiwSoitartoohsrevO/-erP srehto/CSTN
1010
F0
WDHhctiwShtdiWesluPevirDH 00
01
CFAlortnoCniaGCFA txeT/oediV/VT
100010
11SOHnoitallicsOH 70
21
SSH.peScnySHfoleveLecilS 00
31
SSV.peScnySVfoleveLecilS 00
GVTytilanoitcnuF
noitcnuFetoN&elbaT
)deliateD(eulaVlaitinI
yrogetaCoNemaN nommoCCN05CN06CV05CV06CNCSTNCNSREHTOCVCSTNCVSREHTO
PV41
SMHno/ffom/CnoisiVorcaM )06/05(ediW/)06/05(lamroN 10101010
51
VUYLESY 00
61
VDClangisonrednuFRdnaoediVrofedomDC
ylnooediv
10
71
NORNOR
deziromemton
10
81
NOGNOG
deziromemton
10
91
NOBNOB
deziromemton
10
A1
NOPNOP
deziromemton
10
B1
NXAWSSIXA
]ANYDylno[)srehto/CSTN(ediW/)srehto/CSTN(
10101010
C1
LSRLESBGR 00
D1
WBVWKLBV 00
E1
PFRPFER 00
F1
CMVleveLMV 00
02
FBCretliFssapdnaBamorhC 10
12
OTCffOparTamorhC 10
KV-AR29M61/AR29M86/AR29N90
RM-995 RM-993 RM-996
KV-AR29M61/AR29M86/AR29N90
GVTytilanoitcnuF
noitcnuFetoN&elbaT
)deliateD(eulaVlaitinI
yrogetaCoNemaN nommoCcimanyDamarD/dradnatStfoS/eniF-iHwsbanyDwsbamarDwsbtfoS
2PA00
SBBgnitteSleveLtsooBssaB 30
10
BCBlortnoCssaBbuSroftcelestuctsooB 00
20
SBSgnitteSleveLssaBbuS 00
30
TCBlortnoCelberTbuSroftcelestuctsooB 00
40
STSgnitteSleveLelberTbuS 00
50
LGAgnitteSleveLCGA 00
60
WSBhctiwSFFO/NOtsooBssaB 00
70
SABlortnoCedomdnuosssaB }tfos/amard/anyd{*}0/1:WSB{
31
10
10 212020
80
ERTlortnoCedomdnuoselberT }tfos/amard/anyd{*}0/1:WSB{
10
10
70 414120
90
EBBlortnoCedomdnuoSEBB }tfos/amard/anyd{*}0/1:WSB{
09
F7
00 88B600
GVTytilanoitcnuF
noitcnuFetoN&elbaTemaNeciveD
)deliateD(eulaVlaitinI
yrogetaCoNemaN nommoC
PSM00
TSWdlohserhToeretSG/W D5143PSM51
10
TBWdlohserhTlaugniliBG/W CE
20
LLWdlohserhTlaruanoMG/W 50
30
CAWtnuoCtnemeergAG/W 10
40
LDWyaleDhcraeSG/W 03
50 LDNyaleDhcraeSMACIN 02
60
LDSyaleDdaeRsutatsoeretS 01
70
CGAtnatsnoC/otuAhctiwSCGA 10
80
LERedoMtnatsnoCtaniaGCGA 82
90 MRCffo/nognitumreirraC 00
A0
OCAffo/notuokcolCoiduA 10
B0
PFmetsysM-nonrofelacserPMF B1
C0
MPFmetsysMrofelacserPMF 23
D0
HFVEDHrofelacserPMF 63
E0
MHFMdnaVEDHrofelacserPMF 56
F0 PGWelacserPG/W C1
01
PINelacserPMACIN F7
11
RREdlohserhThctiwsMFotuA 05
21
LOVh0ff7oth0007niagrekaepSduoL D6
RM-995 RM-993 RM-996
– 22 –
GVTytilanoitcnuF
noitcnuFemaNeciveD
)deliateD(eulaVlaitinI
yrogetaCoNemaN nommoC
PIP00
ORPelbanEedoMnacSevieergorPX8829ADS00
10DERedoMelbuoDdaeR 00
20
IEFtceleSdleiF 00
30
SPHnoitisoPerutciPlatnoziroH 33
40
SPVnoitisoPerutciPlacitreV B1
50 PFHgninoitisoPeniFlatnoziroH 80
60
PFVgninoitisoPeniFlacitreV 00
70
SIDdradnatsyalpsiD 00
80
SOHeziSlatnoziroH 00
90
SEVeziSlacitreV 00
A0
SPFdradnatStneraPecroF 00
B0
MZHmooZlatnoziroH 00
C0
PSVnoitcudeResioNeluPcnySlacitreV 10
D0
LDVyaleDesluPcnySlacitreV 00
E0
HRFlatnoziroHhtdiWemarF 50
F0
VWFlacitreVhtdiWemarF 20
01
DRVnoitcudeR 00
11
KBVgniknalBlacitreV 00
21
YLDyaleDtceleS 10
31
RCPnoitcerroCnoitisoP 00
41
MGAedoMCGA 30
51
CGAeulaVlortnoCniaGcitamotuA 90
61
BVCtceleSSBVC 00
71
DPCnoitaruDGNIPMALC 10
81
TPCtratsesluPGNIPMALC 10
91
MULtesffoecnanimuL 00
GVTytilanoitcnuF
noitcnuFetoN&elbaT
)deliateD(eulaVlaitinI
yrogetaCoNemaN MACESCSTNLAPVToediVDVD
PIPA1
LLPtnatsnoCemiTLLPtresnIoediV/VT
0000
B1
DCYyaleDC/Y DVD/CSTN/MACES/LAP808080
80
C1
RSNIIPtesnirofnoitcudeResioNoediV/VT
2000
– 23 –
KV-AR29M61/AR29M86/AR29N90
RM-995 RM-993 RM-996
KV-AR29M61/AR29M86/AR29N90
GVTytilanoitcnuF
noitcnuFetoN&elbaT
)deliateD(eulaVlaitinI
yrogetaCoNemaN nommoC0506
PIPD1
PSLdeepSnoitacifitnedIdradnatS 00
E1
LIKdlohserhTrelliKroloC 20
F1
PGBnoitisoPetaGtsruB 10
02
CESleveLnoitacifitnedIMACES 10
12
MEDnoitceleswsahpmeeD 10
22
AMChtiwdnaBamorhC 00
32
CFIretliFnoitasnepmoCFI 20
42
EUHeuH 00
52
ACStnemtsujdAreirracbuSroloC 60
62
NOCtnemtsujdAtsartnoC 00
72
RLBlennahCdeRleveLgniknalB 00
82
TRBtnemtsujdAssenthgirB 30
92
GLBlennahCneerGleveLgniknalB 00
A2
RIBlennahCdeRnoisrevnIgniknalB 00
B2
BIBlennahCeulBnoisrevnIgniknalB 00
C2
BLBlennahCeulBleveLgniknalB 00
D2
TNIlavretnIhserfeR 00
E2
RKPlennahCdeRleveLkaeP 58
F2
GKPlennahCneerGleveLkaeP 58
03
BKPlennahCeulBleveLkaeP 58
13
YRFYroloCemarF 90
23
TUOtamroFtuptuO 10
33
URFUroloCemarF 00
43
VRFVroloCemarF 00
53
TAStnemtsujdAnoitarutaSroloC 90
63
KPYtnemtsujdAkaePY 30
73
OCYelbanEgniroCY 10
83LAPleveLDILAP 30
93VOPlacitreVtesffOnoitisoP 00
A3HOPlatnoziroHtesffOnoitisoP 00
B3
HSVknirhSlacitreV 00
C3
HSHknirhSH 00
D3
LPChtgneLesluPGNIPMALC 10
RM-995 RM-993 RM-996
– 24 –
– 25 –
GVTytilanoitcnuF
noitcnuFetoN&elbaTemaNeciveD
)deliateD(eulaVlaitinI
yrogetaCoNemaN NOMMOCTUPNI-SVTOEDIV
TCY00
UHStnemtsujdAeuHbuSoediV/VTQA3612AXC
E0
21
10
GNPhtdiWetaGCSTN/LAP 10
20
INPWSytivitisneSCSTN/LAP 00
GVTytilanoitcnuF
noitcnuFetoN&elbaT
)deliateD(eulaVlaitinI
yrogetaCoNemaN NOMMOCVT05OEDIV05DVD05VT06OEDIV06DVD06
TCY30LCSlortnoCroloCbuSoediV/VT*06/05
5070
5070
40TCSlortnoCtsartnoCbuSoediV/VT*06-05
5080
5080
50
0FSgnignahCycneuqerFretneCssenprahS 20
60
QEScitsiretcarahCrezilauqEssenprahS 00
70
GHSlortnoCniaGssenprahSDVD/oediV/VT*06/05
607090607090
80LOYlortnoCleveLtuptuo-Y 12
90
PSBgnignahCtnioPtratShctertSkcalB 00
KV-AR29M61/AR29M86/AR29N90
RM-995 RM-993 RM-996
KV-AR29M61/AR29M86/AR29N90
GVTytilanoitcnuF
noitcnuFetoN&elbaT
)deliateD(eulaVlaitinI
yrogetaCoN
emaN NOMMOCTUPNI-SVTOEDIVDVDSREHTO
TCYA0LOClortnoCleveLtuptuOrC/bCsrehto/DVD
72E1
B0
RCDtnemtsujdAoitaRnoitarotseRCD 00
C0
0FBtnemtsujdA0FFQT/FPB 10
D0
QFBtnemtsujdAQFQT/FPB 20
E0
WSFhctiwSFQT/FPB 10
F0
TDShctiwSparTelbuoDMACES 10
01
FPLhctiwSFPLrC/bC/Y 10
11
LDYtnemtsujdAemiTLD-YDVD/tupni-S/oediV/VT
50605050
21
TMChctiwSetuMtuptuOrC/bC 00
31
10B)etuorniam(tnemtsujdA1tesffObC 70
41
1ORtnemtsujdA1tesffOrC 70
51
FDChctiwSycneuqerFnwoDtnuoCV langisonrofzH05decrof00
61
MDChctiwSegduJnwoDtnuoCV 00
71
CFAhctiwSytivitisneSCFADVD/oediV)/VT(
0000
81
MVMksaMCFA+ksaMnoisivorcaM 10
91
YRStnemtsujdAkcalBY-RMACES 70
A1
YBStnemtsujdAkcalBY-BMACES 10
B1
LEBgnihctiwSFPH/LLEBMACES 20
C1
FLBtnemtsujdA0fLLEB 00
D1
IVShctiwSDI-VMACES 00
E1
PGStnemtsujdAnoitisoPetaGMACES 00
F1
DIShctiwSytivitisneSMACESMACEStpecxe10
02
HIShctiwSnoitibihnIMACES 00
12
PTSsulpLAProfputeSleveLkcalBY 00
22
WSAWSedoMtceleSoediVotuA 10
32
HSWnoitcuderesionrofpetSniaGssenprahS 00
42
OCWnoitcuderesionrofpetSleveLtuptuOrC/bC 00
52
2BC)tupni2rCbCY(tnemtsujdatesffo2bC 70
62
2RC)tupni2rCbCY(tnemtsujdatesffo2rC 70
72
HPHhctiwsesahptuptuOSH 00
82
HPVesahptuptuoPVrofhctiwS 00
92
MCNBMOCCSTN 00
RM-995 RM-993 RM-996
– 26 –
GVTytilanoitcnuF
noitcnuFetoN&elbaTemaNeciveD
)deliateD(eulaVlaitinI
yrogetaCoN
emaN NOMMOCCSTNSREHTO
ET00
0RNRN srehtO/CSTNETD
1010
10
0CTgniroCET srehtO/CSTN
5050
20
0GTniaGET srehtO/CSTN
5050
30
HTSssapybET:1ssapybETdecroF 00
40
FOC)215(FFO:1FFOtnenopmoCroloC 00
50
FOYFFO:1FFOtnenopmoCecnanimuL 00
60
RJV2PS:32PS:21PS:1NO:0lortnocrettijV 00
70
FOTFFOET:1FFOET 00
80
FODFFORNtoD:1FFORNtoD 00
90
FOFFFOFPL:1FFOFPLET 10
A0
HTCFFO:1FFOETroloC 00
B0
LSPnoitceleSretemaraPET 20
C0
PLCleveLpmalCtupnI 80
D0
2LCleveLpmalCtuptuO 80
E0
1AL)etihW,+(niaGdnepedleveL 00
F0
2AL)kcalB,+(niaGdnepedleveL 10
01
3AL)etihW,-(niaGdnepedleveL F0
11
4AL)kcalB,-(niaGdnepedleveL 10
21
WRCoitarnoitasnepmocC/YET 40
31
DCYtnemtsujdayaledtuptuoC/YET 40
41
OSOtesffossenprahsffO 00
RN00
OMD)edoMomeD=1(FFO/NOedoMomeDRN ETD00
10
VHTnoitceridlacitrevrofleveldlohserhTesioNfotesffO 30
20
HHTnoitceridlatnozirohrofleveldlohserhTlevelfotesffO 11
30
LLBleveLkcalBrofnoitcetedleveLfotesffO 70
40
TSCleveLroloCrofnoitcetedleveLfotesffO 70
50
CHTdlohserhTnoitceteDegdEfotesffO 90
60
FRN0=knaRsyawla0RN 00
70
GID)nIlatigiD=1(nIlatigiDronID/A 00
TXT00
HXTnoitisoPlatnoziroHtxeteleT 1625AAS00
10
VXTnoitisoPlacitreVtxeteleT 00
– 27 –
KV-AR29M61/AR29M86/AR29N90
RM-995 RM-993 RM-996
KV-AR29M61/AR29M86/AR29N90
GVTytilanoitcnuF
noitcnuFetoN&elbaTemaNeciveD
)deliateD(eulaVlaitinI
yrogetaCoN
emaN NOMMOCCSTNsrehtO
MPO00HSOnoitisoPHDSO csiM-noitpO790057PXCF0
10
MOC ]ETD[)enoN:3,D3:2,itluM:1,enoN:0(/]ETD-NON[)D3:3,itluM:2,CSTN:1,enoN:0(noitceleS 20
)09N/16M92RA-VK(
10
MOC ]ETD[)enoN:3,D3:2,itluM:1,enoN:0(/]ETD-NON[)D3:3,itluM:2,CSTN:1,enoN:0(noitceleS 10
)68M92RA-VK(
20
CPAhctiwSCPA 10
30
YSTsySVTotuAtasySVT 00
40
TUMetuMlangiSoN 00
50
MFAhctiwsMFotuA 10
60
BFRlortnoCFPB-C 00
70
OVTtesffoelgnA-VottliT 20
80
LBDnoitcnuFkcabeulBelbasiD 00
90
OSS)x8:3,x6:2,x4:1,ffO:0(noitpOhcraeSdeepS 10
A0
HCSnoitidnoCgnippihSrofnoitceleSHC ylnosledoMCSTN10
B0
ACSnoitidnocgnippihsrofnoitcelesriA/elbaC ylnosledoMCSTN10
C0
ROPTCYmorFnoitcetceDteseRnOrewoP 00
D0
CRNISCIProfretnuoCteD-N F1
E0
CURdekcolnUretfaretnuoCegnahClangiSFR 40
F0
CLRdekcoLretfaretnuoCegnahClangiSFR 10
01
PYBgniknalBFFO/NOETD 00
11
PLPCIPGNIKNALBFFO/NOIS 00
BPO00
1PO)82egapees(1stiBlanoitpO stiB-noitpO790057PXCFE
10
2PO)82egapees(2stiBlanoitpO 76
20
3PO)82egapees(3stiBlanoitpO 1F
30
4PO)82egapees(4stiBlanoitpO 79
RM-995 RM-993 RM-996
– 28 –
NOTE
•
shaded items are fixed data.
• Standard data listed on the Adjustment Item Table are reference values, therefore it may be different for each model and for each mode.
• Note for Different Data Those are the standard data values written on the microprocessor. Therefore, the data values of the modes and stored respectively in the memory.
In case of a device replacement, adjustment by rewriting the data value is necessary for some items.
ITEM INFORMATION
No. OPB0 OP1
Item
KV-AR29M61
KV-AR29M86
KV-AR29N90
AV Input 00 = no AV Input 01 = 1 AV Input
AR34/29* SHG offset in YCT 0 = AR29/25, 1 = AR34
(APPLICABLE FOR XF-L(21" & 14") MODELS ONLY.
No. OPB1 OP2
Item
KV-AR29M61
KV-AR29M86
KV-AR29N90
AV Input 00 = no AV Input 01 = 1 AV Input
XTAL 4.43
1
1
1
TOP
0
0
0
XTAL 3.58
1
1
1
NICAM
1
1
0
SECAM
1
1
1
HDEV
1
1
0
AR34/29*
0
0
0
Thai Bil
0
0
0
B/G
1
1
0
PIP 4
0
1
0
10 = 2 AV Input 11 = 3 AV Input
KV-AR29M61/AR29M86/AR29N90
RM-995 RM-993 RM-996
I
1
1
0
DVD Input
1
1
1
D/K
1
1
0
AV Input
1
1
1
M
1
1
1
1
1
1
DVD Input Effective only when "AV Input" is set to 3 AV Input
PIP 4 PIP 4 0 = disabled, 1 = enabled
No. OPB2 OP3
Item
KV-AR29M61
KV-AR29M86
KV-AR29N90
Initial menu
1
1
1
AP2
1
1
1
Initial Menu Initial Menu Setup 0 = disabled, 1 = enabled
AP2 Auto Processor Selection 0 = AP, 1 = AP2.
Auto PIC
*3
A-TVsys Auto TV System in Auto Program0 = disabled, 1 = enabled
*
US ST
DTE DTE Model Selection 0 = Non DTE, 1 = DTE
Forced 50/60 Forced to 50/60 Hz during no signal condition 0=60Hz, 1=50Hz
Color SW
*2
Note:*1 - For XA21/XH29 Models Only
*2
- For XA34/29/25 Models Only
*3
- For PNC3, the enables are from service item APG and APB.
Auto PIC
1
1
1
A-TVsys
1
1
0
US ST
0
0
1
DTE
0
1
0
Forced 50/60
0
0
0
Colour SW
1
1
1
Auto Picture Improvement 0 = off PNC1/PNC2
1 = activate PNC1/PNC2
USA Stereo 0 = disabled, 1 = enabled
Color Data Selection in Dynamic Mode 0 = 65 (No PIP), 1 = 57 (PIP)
2
*
No. OPB3 *OP4
Item
KV-AR29M61
KV-AR29M86
KV-AR29N90
PNC2
1
0
1
Korean ST
0
0
0
Vid NTSC3.58
APPLICABLE TO XS ONLY - Sub Language Selection (Bit 0 - Bit 2)
Korean Stereo* Korean Stereo 0 = disabled, 1 = enabled
2
PNC2*
Enable switch of PNC2 0 = disable, 1 = enable
Video NTSC3.58* Video Color System 0 = Multi System, 1 = Single System (NTSC3.58)
Wide Enable wide mode 0 = disable, 1 = enable
Note : *APPLICABLE FOR NTSC MODELS ONLY
0
0
0
– 29 –
Wide
1
1
1
Video3
0
0
0
Chinese(multi mdl)
1
1
0
Arabic/C.Chinese
Thai/Korean
1
1
1
1
1
0
Loading...