Sony KD-34XS955N Operating Instructions

4-102-728-21 (1)

Sony Corporation http://www.sony.net

Printed in U.S.A.

KD-30XS955 I KD-34XS955 I KD-36XS955

Operating Instructions

WARNING

To reduce the risk of fire or shock hazard, do not expose the TV to rain or mois ture.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

ATTENTION

RISQUE DE CHOC ELECTRIQUE,

NE PAS OUVRIR

PRECAUCION

RIESGO DE CHOQUE ELECTRICO

NO ABRIR

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electr ic shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE S LOT, FULLY INSERT.

CAUTION

When usi ng TV games, computer s, and similar products with y our TV, keep the brightness and contrast functions at low settings. If a fixed (non-moving) pattern is left on the screen for long periods of time at a high brightness or contrast setting, the image can be permanently imprinted onto the screen. Continuously watching the same program can cause the imprint of station logos onto the TV screen. These types of imprints are not covered by your warranty because they are the result of misuse.

Warning (KD-34XS955 only)

The CRT in this product employs a protective film on the face. This film must not be removed as it serves a safety function and removal will increase the risk of serious injury.

Note on Caption Vision

This television receiver provides display of television closed captioning in accordance with §15.119 of the FCC rules.

Note on Cleaning the TV

Clean the TV with a soft, dry cloth. Never use strong solvents such as thinner or benzine, which might damage the finish of the cabinet.

Note to CATV System Installer

This reminder is provided to call the CATV system installer ’s attention to Article 820-40 of the National Electrical Code (NEC) that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

Use of this television receiver for other than priv ate viewing of programs broadcast on UHF or VHF or transmitted by cable companies for the use of the general public may require authorization from the broadcaster/cable company and/or program owner.

NOTIFICATION

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference with radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

❑ Reorient or relocate the receiving antennas. ❑ Increase the separation between the equipment and receiver. ❑ Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

❑ Consult the dealer or an experienced radio/TV technician for

help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

Installing

To prevent internal heat buildup, do not block the ventilation

❑

openings.

❑ Do not install the TV in a hot or humid place, or in a place

subject to excessive dust or mechanical vibration.

❑ The AC power cord is attached to the rear of the TV with

hooks. Do not attempt to remove the cord from these hooks. Doing so could cause damage to the TV.

Owner’s Record

The model and serial numbers are provided on the front of this instruction manual and at the rear of the TV. Refer to them whenever you call upon your Sony dealer regarding this product.

Note

This digital television is capable of receiving analog basic, digital basic and digital premium cable television programming by direct connection to a cable system providing such programming. A security card provided by your cable operator is required to view encrypted digital programming. Certain advanced and interactive digital cable services such as video-on-demand, a cable operator's enhanced program guide and data-enhanced television services may require the use of a set-top box. For more information call your local cable operator.

This television also includes a QAM demodulator which should allow you to receive unscrambled digital cable television programming via subscription service to a cable service provider. Availability of digital cable television programming in your area depends on the type of programming and signal provided by your cable service provider.

IMPORTANT SAFEGUARDS

For your protection, please read thes e instructions completely, and keep this manual for future reference.

Carefully observe and comply with all warnings, cautions and instructions placed on the set, or described in the operating instructions or service manual.

WARNING

To guard against injury, the following basic safety precautions should be observed in the installation, use, and servicing of the set.

Use

Power Sources

This set should be operated only from the type of power source indicated on the serial/model plate. If you are not sure of the type of electrical power supplied to your home, consult your dealer or local power company. For those sets designed to operate from batt ery power, refer to the operating instructions.

Grounding or Polarization

This set is equipped with a polarized AC power cord plug (a plug having one blade wider than the other), or with a three-wire grounding type plug (a plug having a third pin for grounding). Follow the instructions below:

For the set with a polarized AC power cord plug

This plug will fit into the power outlet only one way. Thi s is a safe ty fe ature. If you are unab le to insert the plug fully into the outlet, try reversing the plug. If the plug should s till fail to fit, conta ct your elect rician to have a suitable outlet installed. Do not defeat the safety purpose of the polarized p lug by forcing it in.

Alternate Warning

For the set with a three-wire grounding type AC plug

This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to have a suitable outlet installed. Do not defeat the safety purpose of the grounding plug.

Overloading

Do not overload wall outlets, extension cords or convenience receptacles beyond their capacity, since this can result in fire or electric shock.

Always turn the set off when it is not to be used. When the set is left unattended and unused for long periods of time, unplug it from the wall outlet as a precaution against the possibility of an internal malfunction that could create a fire hazard.

Do not disconnect the antenna or the power cord during a heavy storm. Lightning may strike while you are holding the cable or cord, causing serious injury. Turn off your TV and wait for the weather to improve.

Memory Stick

To protect small children from injury from Memory Stick Media, remove all Memory Stick media from the TV’s Memory Stick slot and store it in a safe location when it is not in use.

Object and Liquid Entry

Never push objects of any kind into the set through the cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the set.

Attachments

Do not use attachments not recommended by the manufacturer, as they may cause hazards.

Do not place any objects, especially heavy objects, on top of the set. The object may fall from the set, causing injury.

Cleaning

Unplug the set from the wall outlet before cleaning or polishing it. Do not use liquid cleaners or aerosol cleaners. Use a cloth lightly dampened with water for cleaning the exterior of the set.

If a snapping or popping sound from a TV set is continuous or frequent while the TV is operating, unplug the TV and consult your dealer or service technician. It is normal for some TV sets to make occasional snapping or popping sounds, particularly when being turned on or off.

Installation

Always use two or more people to lift or move the set. The set is heavy and the bottom surface is flat. Serious injury can result from trying to move the set by yourself alone, or from unsteady handling. Inst all the set on a stable, level surface.

Water and Moisture

Do not use power-line operated sets near water — for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc.

Accessories

Do not place the set on an unstable cart, stand, tripod, bracket, table or shelf. The set may fall, causing serious injury to a child or an adult, and serious damage to the set. Us e only a cart or stand recommended by the manufacturer for the specific model of TV. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

Disconnect all cables and cords from the set before attempting to move the set.

Do not allow children or pets to climb up onto, or push against, the set. The set may fall, causing serious injury.

Ven til ati on

The slots and openings in the cabinet and in the back or bottom are provided for necessary ventilation. To ensure reliable operation of the set, and to protect it from overheating, these slots and openings must never be blocked or covered.

❑ Never cover the slots and openings with a

cloth or other materials.

❑ Never block the slots and openings by

placing the set on a bed, sofa, rug or other similar surface.

❑ Never place the set in a confined space, such

as a bookcase, or built-in cabinet, unless proper ventilation is provided.

❑ Do not place the set near or over a radiator

or heat register, or where it is exposed to direct sunlight.

Power Cord Protection

Do not allow anything to rest on or roll over the power cord, and do not place the set where the power cord is subject to wear or abuse.

Antennas

Outdoor Antenna Grounding

If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits.

WHEN INSTALLING AN OUTDOOR ANTENNA SYSTEM, EXTREME CARE SHOULD BE TAKEN TO KEEP FROM CONTACTING SUCH POWER LINES OR CIRCUITS AS CONTACT WITH THEM IS ALMOST INVARIABLY FATAL.

Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up sta tic charges. Section 810 of the National Electrical Code (NEC) in USA and Section 54 of the Canadian Electrical Code in Canada provide information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

Antenna Grounding According to the National Electrical Code, ANSI/NFPA 70

Antenna lead-in wire

Ground clamp

Antenna discharge unit (NEC Section 810-20)

Electric service equipment

NEC: National Electrical Code

Ground ing conductors (NEC Section 810-21)

Ground clamps

Power service grounding electrode system (NEC Art 250 Part H)

Lightning

For added protection for this television receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage to the receiver due to lightning and power line surges.

Service

Damage Requiring Service

Unplug the set from the wall outlet and refer servicing to q ualified service personnel under the following conditions:

❑ When the power cord or plug

is damaged or frayed.

❑ If liquid has been spilled into

the set or objects have fallen into the product.

❑ If the set has been exposed to rain or

water.

❑ If the set has been subject to excessive

shock by being dropped, or the cabinet has been damaged.

❑ If the set does not operate normally when

following the operating instructions. Adjust only those controls that are specified in t he oper ating instructions. Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the set to normal operation.

❑ When the set exhibits a distinct change in performance, it

indicates a need for service.

Servicing

Do not attempt to service the set y ourself since opening the cabinet may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

Replacement Parts

When replacement parts are required, be sure the service technician certifies in writing that he has used replacement parts specified by the manufacturer that have the same characteristics as the original parts.

Unauthorized substitutions may result in fire, electric shock or other hazards.

Safety Check

Upon completion of any service or repairs to the set, ask the service technician to perform routine safety checks (as specified by the manufacturer) to determine that the set is in safe operating condition, and to so certify. When the set reaches the end of its useful life, improper disposal could result in a picture tube implosion. Ask a qualified service technician to dispose of the set.

Trademark Information

WOW, TruSurround and the symbol are trademarks of SRS Labs, Inc. WOW and TruSurround technology are incorporated under license from SRS Labs, Inc.

Manufactured under license from Dolby Labora tories Licensing Corporation. Dolby and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.

Manufactured under license from BBE Sound, Inc. Licensed by BBE Sound, Inc. under USP4638258, 5510752 and 5736897. BBE and BBE symbol are registered trademarks of BBE Sound, Inc.

This TV incorporates High-Definition Multimedia Interface (HDMI™)

High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

CableCARD™ is a trademark of Cable Television Laboratories, Inc.

Wega, FD Trinitron, Steady Sound, Digital Reality Creation, CineMotion, Memory Stick, Memory Stick Duo, Memory Stick PRO, Memory Stick PRO Duo, MagicGate, Super Fine Pitch, MID, Clear Edge, ClearEdge VM and HD Detailer are trademarks of Sony Corporation.

technology. HDMI, the HDMI logo and

Introducing the FD Trinitron Wega

Overview ....................................................................................................... 9

Presenting the FD Trinitron Wega ............................................................... 9

Package Contents.............................................................................. 9

Features ............................................................................................ 9

Setting Up the TV

Overview .....................................................................................................11

About the AC Power Cord............................................................... 11

TV Controls and Connectors.......................................................................12

Front Panel .....................................................................................12

Rear Panel ....................................................................................... 13

Basic Connections: Connecting a Cable or Antenna.................................15

About Using CableCARD .................................................................15

Cable or Antenna Only ....................................................................16

Cable and Antenna Only .................................................................17

Cable Box and Cable Only ............................................................... 18

Cable Box Only ................................................................................ 19

Connecting Optional Equipment ...............................................................20

Making Video Connections ..............................................................21

About Using S VIDEO ...................................................................... 21

VCR and Cable ................................................................................22

VCR and Cable Box .........................................................................24

Two VCRs for Tape Editing ..............................................................26

Satellite Receiver.............................................................................. 28

Satellite Receiver and VCR ...............................................................30

DVD Player with Component Video Connectors...............................32

DVD Player with S VIDEO and Audio Connectors ............................. 34

Camcorder ......................................................................................35

Audio Receiver ................................................................................36

DVI-Equipped Device .......................................................................37

HDMI-Equipped Device .................................................................... 38

Connecting a Device with an Optical IN Connector .................................39

Using the CONTROL S Feature ...................................................................40

Using CableCARD ........................................................................................41

About Using CableCARD .................................................................41

Activating CableCARD Service ......................................................... 41

Removing the CableCARD ...............................................................42

Setting Up the Channel List .......................................................................43

Using Initial Setup ............................................................................ 43

Using the Remote Control

Overview .....................................................................................................45

Inserting Batteries.......................................................................................45

Button Descriptions ....................................................................................46

Programming the Remote Control ............................................................49

Using the Features

Overview .....................................................................................................51

Watching TV ................................................................................................52

Using the Program Guide ........................................................................... 53

Using Screen Mode (models KD-30/34XS955 Only)..................................55

Using Screen Mode (models KD-36XS955 Only).......................................57

Using Favorite Channels .............................................................................58

Using Other Equipment with Your TV Remote Control...........................59

Using the Memory Stick Viewer

About Memory Stick ................................................................................... 61

Inserting and Removing a Memory Stick .................................................. 64

Using the Memory Stick Index ...................................................................66

Viewing Photos ........................................................................................... 68

Playing Movies ............................................................................................ 71

Memory Stick Index Menu Bar Options .................................................... 73

Notes on Using Memory Stick Media ........................................................75

Other Info SETUP WelcomeSETUP SETUPSETUP

Using Additional Program Guide Options.........................................54

Using the Channel Menu ................................................................. 58

Using the Favorite Channels Guide .................................................. 58

All Equipment..................................................................................59

Operating a VCR .............................................................................59

Operating a Satellite Receiver ..........................................................59

Operating a Cable Box.....................................................................60

Operating a DVD Player ...................................................................60

Operating a DVD/VCR Combination Unit .........................................60

Features ..........................................................................................61

Memory Stick Compatibility ............................................................. 62

Memory Stick Functionality ..............................................................62

File Compatibility .............................................................................63

Trademark Information .................................................................... 63

Inserting a Memory Stick ................................................................. 64

Removing a Memory Stick ............................................................... 65

Using the Memory Stick Index ......................................................... 67

Photo Controls ................................................................................ 68

Photo Menu Bar Options ................................................................. 69

Using Zoom and Pan .......................................................................70

Using Rotate....................................................................................70

Movie Controls................................................................................71

Movie Menu Bar Options ................................................................. 72

Slide Show Menu Options ...............................................................73

Contents Menu Options ..................................................................74

Memory Stick Menu ........................................................................74

About DCF File Names ..................................................................... 75

Memory Stick Precautions................................................................76

Using the Menus

Other Information

Overview .....................................................................................................77

Navigating Through Menus .......................................................................77

Using the Video Menu................................................................................78

Using the Audio Menu ...............................................................................80

Using the Screen Menu (models KD-30/34XS955 Only) ...........................82

Using the Screen Menu (model KD-36XS955 Only)..................................83

Using the Channel Menu ............................................................................84

Using the Parent Menu...............................................................................86

Using the Setup Menu................................................................................89

Using the Applications Menu.....................................................................92

Overview .....................................................................................................95

Glossary ....................................................................................................... 96

Contacting Sony .......................................................................................... 97

Troubleshooting..........................................................................................97

Remote Control ...............................................................................97

Channels .........................................................................................98

CableCARD .....................................................................................98

Memory Stick ..................................................................................99

Audio ............................................................................................100

Video ............................................................................................101

General ......................................................................................... 101

Specifications ............................................................................................ 103

Optional Accessories......................................................................104

Index .......................................................................................................... 105

Welcome SETUP Other InfoSETUP SETUPSETUP

Introducing the FD Trinitron Wega

Overview

This chapter describes the contents of the package in which the TV is shipped and provides an overview of the features of your Wega TV.

Presenting the FD Trinitron Wega

The FD Trinitron Wega (pronounced VAY-GAH) is characterized by outstanding contrast, uncompromising accuracy, and corner-tocorner detail.

You will recognize the superiority of Wega technology almost immediately. The first thing you will probably notice is minimal glare from the flat picture tube. This flat-screen technology improves picture detail without distortion, unlike conventional curved screens. The FD Trinitron delivers outstanding image detail not only at the screen center, but also at the corners — so you can enjoy a bright, clear picture from any location in a room.

Package Contents Along with your new Trinitron TV, the packing box contains a remote

control and two AA (R6) batteries. These items are all you need to set up and use the TV.

Features Some of the features that you will enjoy with your new TV include:

❑ Built-in Digital Television Receiver: Yo u can w a tch d i g i t al

television programs and enjoy the improved audio/video quality offered by these programs. With high-definition signal reception, you can watch TV signals broadcast in HDTV for the clearest possible broadcast picture.

❑ CableCARD slot: Provides cable subscribers with access to

digitally encrypted cable channels — without the need for a settop box — that will enable you to receive not only standard definition but also high definition television. The CableCARD, which is provided by your cable TV company, is inserted into the TV’s rear panel CableCARD slot. After the service is activated with your cable TV company, the card replaces the need for a separate set-top box. (Check with your cable TV company about CableCARD service details, limitations, pricing, and availability. For more information about CableCARD in this manual, see pages 15 and 41.)

❑ Screen Mode: Enables you to resize the picture. ❑ Super Fine Pitch CRT: Created especially for displaying high

resolution pictures, the new Super Fine Pitch CRT — along with a new electron gun and high intensity luminescent phosphor — improves image resolution, providing the highest picture quality reproduction from corner to corner.

❑ DRC

(Digital Reality Creation) Multifunction: Unlike conventional line doublers, the DRC Multifunction feature replaces the signal’s NTSC waveform with the near-HD equivalent, while doubling the number of vertical and horizontal lines. This results in four times the density for quality sources, such as DVD, satellite, and digital camcorders. The Video Menu allows you to select interlaced, progressive, or CineMotion™ output.

❑ Favorite Channels: Allows you to select from 16 of your favorite

channels.

❑ ClearEdge VM

™

Velocity Modulation: Sharpens picture

definition by enhancing vertical lines.

❑ Steady Sound

: Equalizes volume levels so there is consistent

output between programs and commercials.

❑ Memory Stick

Viewer: Lets you watch digital photo (JPEG) and

movie (MPEG1) files that are stored on Memory Stick media.

❑ Component Video Inputs: Offers the best video quality for DVD

(480p, 480i), and digital set-top box (HD1080i, 720p) connections.

❑ HD Detailer

™

: Wideband video amplifier has a high bandwidth frequency rating, which allows it to send more video information to the screen, resulting in finer picture quality, especially for HD sources.

❑ CineMotion

™

: Reverse 3-2 pulldown processing provides optimal picture quality for film-based sources (media originally shot in 24 frames-per-second format).

❑ Parental Control: V-Chip technology allows parents to block

unsuitable programming from younger viewers.

❑ HDMI (High-Definition Multimedia Interface): Provides an

uncompressed, all-digital audio/video interface between this TV and any HDMI-equipped audio/video component, such as a settop box, DVD player, and A/V receiver. HDMI supports enhanced, or high-definition video, plus two-channel digital audio.

SETUP SETUP WelcomeSETUP SETUPSETUP

Introducing

Setting Up the TV

Overview

This chapter includes illustrated instructions for setting up your TV.

Topi c Page(s)

TV Controls and Connectors 12-14

Basic Connections: Connecting a Cable or Antenna 15-19

Connecting Optional Equipment

VCR and Cable VCR and Cable Box Two VCRs for Tape Editing Satellite Receiver Satellite Receiver and VCR DVD Player with Component Video Connectors DVD Player with S VIDEO and Audio Connectors Camcorder Audio Receiver DVI-Equipped Device HDMI-Equipped Device

Connecting a Device with an Optical IN Connector 39

Using the CONTROL S Feature 40

Using CableCARD 41

Setting Up the Channel List 43

24 26 28 30 32 34 35 36 37 38

About the AC Power Cord

The AC power cord is attached to the rear of the TV with a hook. Use caution when removing the AC plug from its holder. Gently slide the plug upward to remove it from the hook. Once removed, the AC power plug should automatically disengage from its stored location.

✍ Do not plug in the AC power cord until you have made all other

connections.

You can detac h the cord from this hook

AC power cord

TV Controls and Connectors

Front Panel

S VIDEO

VIDEO 2 INPUT

L(MONO) – AUDIO – R

VIDEO

TV/VIDEO

VOLUME

CHANNEL

STD/DUO

STAND BY

TIMER

POWER

Item Description

1 S VIDEO

VIDEO 2 INPUT

Connects to the S VIDEO OUT jack on your camcorder or other video equipment that has S VIDEO. Provides better picture quality than composite video (2).

2 VIDEO/L(MONO)-AUDIO-R

VIDEO 2 INPUT

Connects to the composite A/V output jacks on your camcorder or other video equipment.

3 MENU Press to display the Menu. Press again to exit from the Menu. For details, see

“Using the Menus” on page 77.

Vv B b Press Vv B b to move the TV’s on-screen cursor.

4 5

Press to select an item in the TV’s Menu.

6 Press to display the Memory Stick Menu. For details, see “Using the Memory

Stick Viewer” on page 61.

7 TV/VIDEO Press repeatedly to cycle through the video equipment connected to the TV’s

video inputs.

8 -VOLUME + Press to adjust the volume. 9 -CHANNEL+ Press to scan through channels. To scan quickly through channels, press and

hold down either CHANNEL button.

0 PRO STD/DUO Memory Stick insertion slot. For details, see “Inserting and Removing a Memory

Stick” on page 64.

qa Memory Stick LED When lit, indicates that the Memory Stick is being read. (Do not remove the

Memory Stick when the indicator is lit.)

qs TIMER/STAND BY LED Blinks when the TV is turned on, then shuts off when the picture is displayed. If

the LED blinks continuously, this may indicate the TV needs service (see “Contacting Sony” on page 97). When lit, indicates one of the timers is set. When the timer is set, this LED will remain lit even if the TV is turned off. For details, see page 92.

qf Infrared Receiver (IR) Receives IR signals from the TV’s remote control. qg POWER Press to turn on and off the TV.

SETUP SETUP SETUPSETUP SetupSETUP

Rear Panel

SETUP Setup SETUPSETUP SETUPSETUP

Jack Description

1 VHF/UHF RF input that connects to your VHF/UHF antenna or cable box. 2 S VIDEO IN 1/3 Connects to the S VIDEO OUT jack of your VCR or other video equipment that has

S VIDEO. S VIDEO provides better picture quality than either composite video (3) or VHF/UHF (1) connections.

3 VIDEO IN 1/3/4

VIDEO/L(MONO)

-AUDIO-R

4 MONITOR OUT Lets you record the program you are watching to a VCR. When two VCRs are

5 AUDIO OUT (VAR/FIX) Connects to the left and right audio input jacks of your audio or video equipment.

6 HD/DVD IN 5/6

(1080i/720p/480p/480i)

7 CONTROL S

IN/OUT

8 HDMI

(VIDEO 7 IN)

9 DIGITAL AUDIO OPTICAL

OUTPUT (DOLBY DIGITAL PCM)

0 CableCARD Slot Provides cable subscribers with access to digitally encrypted cable channels —

qa Cable RF input that connects to your cable signal.

Connect to the composite A/V output jacks on your VCR or other video component. A fourth component A/V input jack (VIDEO 2) is located on the front panel of the TV. This video connection provides better picture quality than the VHF/UHF (1) connection.

connected, you can use the TV as a monitor for tape-to-tape editing (not available with digital channels or with 480i, 480p, 720p, or 1080i when the input is set to VIDEO 5, 6, or 7).

You can use these outputs to listen to your TV’s audio through your stereo system.

Connect to your DVD player’s or digital set-top box’s component video (Y, P and audio (L/R) jacks. Component video provides better picture quality than 1,

2, or 3).

Allows the TV to receive (IN) and send (OUT) remote control signals to other Sony infrared-controlled audio or video equipment that has the CONTROL S function.

HDMI (High-Definition Multimedia Interface) provides an uncompressed, alldigital audio/video interface between this TV and any HDMI-equipped audio/video component, such as a set-top box, DVD player, and A/V receiver. HDMI supports enhanced, or high-definition video, plus two-channel digital audio.

Connect to the optical audio input of an audio component that is Dolby* Digital and PCM compatible.

without the need for a set-top box — that will enable you to receive not only standard definition but also high definition television. The CableCARD, which is provided by your cable TV company, is inserted into this slot. After the service is activated with your cable TV company, the card replaces the need for a separate settop box. Check with your cable TV company about CableCARD service details, limitations, pricing, and availability. For more information, see page 41.

B, PR)

* Dolby and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.

SETUP SETUP SETUPSETUP SetupSETUP

Basic Connections: Connecting a Cable or Antenna

The way in which you will connect your TV varies, depending on how your home receives a signal (cable, cable box, antenna) and whether or not you plan to connect a VCR.

If You Are Connecting See Page

Cable or Antenna Only

❏ No cable box or VCR

Cable and Antenna Only

❏ No cable box or VCR

Cable Box and Cable Only

❏ Cable box unscrambles only some

channels (usually premium channels)

❏ No VCR

Cable Box Only

❏ Cable box unscrambles all channels ❏ No VCR

If you are connecting a VCR

❑

See the connections described on pages 22 and 24.

About Using CableCARD

If you are planning to use a separate cable box for digital cable TV services, you may be able to receive programming using this TV with the CableCARD instead — except in the following circumstances:

SETUP Setup SETUPSETUP SETUPSETUP

❑ Your cable TV company does not provide CableCARD service in your viewing area.

❑ You want to access your cable company’s interactive or advanced features (such as video-

on-demand or, in some cases, pay-per-view). At this time, these services require a bidirectional link, which are only available through the use of a separate set-top box. CableCARD is currently a unidirectional device only, and cannot provide these advanced services.

Check with your cable TV company for CableCARD service details, limitations, pricing, and availability, all of which are determined by your cable TV company — not Sony. For information on installing and activating CableCARD, see “Using CableCARD” on page 41.

Cable or Antenna Only

For best results, use one of the following connections if you are connecting a cable or an antenna and you:

❑

Do not need a cable box to unscramble channels. (If you have a cable box, see pages 18-19.)

❑ Do not intend to connect a VCR. (If you have a VCR, see pages 22

and 24.)

The connection you choose depends on the cable type you have in your home, as described below.

75-ohm coaxial cable (usually found in newer homes)

Cable Type Connect As Shown

VHF Only or combined VHF/UHF

75-ohm coaxial cable

VHF/UHF

Cable

75-ohm coaxial cable

300-ohm twin lead cable (usually found in older homes)

Cable Type Connect As Shown

VHF Only or UHF Only or

300-ohm twin lead cable

CABLE

combined VHF/UHF

Antenna connector (not supplied)

75-ohm coaxial and 300-ohm twin lead cable (found in some homes)

Cable Type Connect As Shown

VHF and UHF

75-ohm coaxial cable

VHF/UHF

U/V mixer

(not supplied)

300-ohm twin

SETUP SETUP SETUPSETUP SetupSETUP

lead cable

VHF/UHF

Cable and Antenna Only

For best results, use this connection if you:

❑

Have a cable and an antenna.

(This is convenient if you are using a separate rooftop antenna to receive additional channels that are not provided by your cable company.)

❑ Do not have a cable box or VCR. (If you have a cable box, see

pages 18 to 19. If you have a VCR, see pages 22 and 24.)

Cable Type Connect As Shown

Cable TV (CATV) and Antenna

Notes on Using This Connection

To Do This ... Do This ...

Switch the TV’s input between the cable and antenna

Press ANT to switch back and forth between the TV’s VHF/UHF and CABLE inputs.

SETUP Setup SETUPSETUP SETUPSETUP

Antenna cable CATV cable

Cable Box and Cable Only

Before connecting a cable

box, see “About Using

CableCARD” on page 15.

For best results, use this connection if:

❑

Your cable company scrambles some channels, such as premium channels (which requires you to use a cable box), but does not scramble all channels.

❑ You do not have a VCR. (If you have a VCR, see pages 22 and 24.)

With this connection you can:

❑

Use the TV remote control to change channels coming through the cable box to the TV’s VHF/UHF input jack. (You must first program the remote control for your specific cable box; see “Programming the Remote Control” on page 49.)

❑ Use the TV remote control to change channels coming directly

into the TV’s CABLE input. (The TV’s tuner provides a better signal than the cable box.)

Splitter

CATV cable

Coaxial cable

Notes on Using This Connection

To Do This ... Do This ...

Use the cable box Tune the TV to the channel the cable box is set to (usually channel 3 or 4)

and then use the cable box to switch channels.

Set up the TV remote control to operate the cable box

Activate the remote control to operate the cable box

Switch

the TV’s input

between the cable box and cable

Program the remote control. See “Programming the Remote Control” on pages 49-50.

Press SAT/CABLE FUNCTION.

Press ANT to switch back and forth between the TV’s VHF/UHF (scrambled channels) and CABLE (unscrambled) inputs.

Coaxial cable

Cable box

VHF/UHF

CABLE

SETUP SETUP SETUPSETUP SetupSETUP

Cable Box Only For best results, use this connection if:

❑

Your cable company scrambles all channels, which requires you

Before connecting a cable

box, see “About Using

CableCARD” on page 15.

to use a cable box.

❑ You do not have a VCR. (If you have a VCR, see pages 22 and 24.)

With this connection you can:

❑

Use the TV remote control to change channels coming through the cable box to the TV’s VHF/UHF jack. (You must first program the remote control for your specific cable box.)

To connect the cable box

1 Connect the CATV cable to the cable box’s input jack. 2 Use a coaxial cable to connect the cable box’s output jack to the

TV’s VHF/UHF jack.

CATV cable

Coaxial cable

VHF/UHF

SETUP Setup SETUPSETUP SETUPSETUP

Cable box

OUT

3 Run Auto Program, as described in “Setting Up the Channel List”

on page 43.

Notes on Using This Connection

To Do This ... Do This ...

Use the cable box Tune the TV to the channel the cable box is set to (usually channel 3 or 4)

and then use the cable box to switch channels.

Set up the TV remote control to operate the cable box

Activate the remote control to operate the cable box

Program the remote control. See “Programming the Remote Control” on pages 49.

Press SAT/CABLE FUNCTION.

Connecting Optional Equipment

Use the directions in this section to connect the following optional equipment:

If You Are Connecting See Page

VCR and Cable 22

VCR and Cable Box 24

Two VCRs for Tape Editing 26

Satellite Receiver 28

Satellite Receiver and VCR 30

DVD Player with Component Video Connectors

DVD Player with S VIDEO and Audio Connectors

Camcorder 35

Audio Receiver 36

DVI-Equipped Device 37

HDMI-Equipped Device 38

SETUP SETUP SETUPSETUP SetupSETUP

Making Video Connections

Your TV includes several types of video inputs. When connecting your TV, use the inputs that are available on your components that provide the best video performance, as described below.

Best Video Performance

HDMI (High-Definition Multimedia Interface)

Component video

S VIDEO

Composite video

RF/Coaxial

Good Video Performance

SETUP Setup SETUPSETUP SETUPSETUP

About Using SVIDEO

Example of an S VIDEO Connection

S VIDEO

Equipment with S VIDEO

If the optional equipment you are connecting has an S VIDEO jack (shown at left), you can use an S VIDEO cable for improved picture quality (compared to an A/V cable). Because S VIDEO carries only the video signal, you also need to connect audio cables for sound, as shown below.

cable

Cables are often

color-coded to connectors.

Connect red to red, white to white, etc.

Audio cable

VCR and Cable For best results, use this connection if:

❑

Your cable company does not require you to use a cable box.

To connect the VCR and cable

Using S VIDEO jacks? See page 21.

1 Connect the CATV cable to the VCR’s VHF/UHF input jack. 2 Use a coaxial cable to connect the VCR’s VHF/UHF output jack

to the TV’s CABLE jack.

3 Use an A/V cable to connect the VCR’s A/V output jacks to the

TV’s A/V input jacks.

4 Run Auto Program, as described in “Setting Up the Channel List”

on page 43.

Coaxial cable

VCR

CATV cable

A/V cable

Cables are often

color-coded to connectors.

Connect red to red, white to white, etc.

SETUP SETUP SETUPSETUP SetupSETUP

Notes on Using This Connection

To Do This ... Do This ...

Watch the VCR Press TV/VIDEO repeatedly to select the VCR input (VIDEO 1 in the

illustration).

Watch cable channels Press TV/VIDEO repeatedly to select the cable input (CABLE in the

illustration).

Set up the TV remote control to operate the VCR

Activate the TV remote control to operate the VCR

Control VCR functions with the TV remote control

Label video inputs to easily identify equipment connected to the TV

If you have a non-Sony VCR, you must program the remote control. See “Programming the Remote Control” on pages 49-50.

Press VCR/DVD FUNCTION.

See “Operating a VCR” on page 59.

See the instructions for setting up Video Labels on page 90.

SETUP Setup SETUPSETUP SETUPSETUP

VCR and Cable Box For best results, use this connection if:

❑

Your cable company scrambles some channels, such as premium

Before connecting a cable

box, see “About Using

CableCARD” on page 15.

channels (which requires you to use a cable box), but does not scramble all channels.

With this connection you can:

❑

Use the TV remote control to change channels coming through the cable box. (You must first program the remote control for your specific cable box; see “Programming the Remote Control” on page 49.)

❑ Use the TV remote control to change channels coming directly

into the TV’s CABLE jack. (The TV’s tuner provides a better signal than the cable box.)

❑ Record channels coming through the cable box and channels

coming directly into the TV.

To connect a VCR and cable box, you need:

❑

A splitter, which is a small, inexpensive device that you can purchase at your local electronics store.

❑ Four coaxial cables.

❑ Two A/V cables or two S VIDEO cable with audio cables.

To connect the VCR and cable box

1 Connect the CATV cable to the single (input) jack of the splitter. 2 Use a coaxial cable to connect one of the splitter’s two output

jacks to the TV’s CABLE jack.

3 Use a coaxial cable to connect the splitter’s other output jack to

the cable box’s input jack.

4 Use a coaxial cable to connect the cable box’s output jack to the

VCR’s RF input jack.

5 Use an A/V cable to connect the cable box’s A/V output jacks to

Using S VIDEO jacks? See page 21.

the TV’s A/V input jacks.

6 Use an A/V cable to connect the VCR’s A/V output jacks to the

TV’s A/V input jacks.

7 Run Auto Program, as described in “Setting Up the Channel List”

on page 43.

SETUP SETUP SETUPSETUP SetupSETUP

A/V cable

Coaxial

cable

Cable box

Coaxial

cable

VCR

Splitter

(not supplied)

Cables are often

color-coded to connectors.

Connect red to red, white to white, etc.

Coaxial

cable

CATV cable

SETUP Setup SETUPSETUP SETUPSETUP

Notes on Using This Connection

To Do This ... Do This ...

Watch cable (unscrambled) channels

Watch cable box (scrambled) channels

Press TV/VIDEO repeatedly to select the cable input (CABLE in the illustration).

Press TV/VIDEO repeatedly to select the cable box input (VIDEO 3 in the illustration). Use the cable box to change channels.

Watch the VCR Press TV/VIDEO repeatedly to select the VCR input (VIDEO 1 in the

illustration).

Set up the TV remote control to operate the cable box or

If you have a non-Sony VCR, you must program the remote control. See “Programming the Remote Control” on pages 49-50.

VCR

Activate the remote control to operate the cable box or VCR

Control specific cable box and

For the cable box, press SAT/CABLE FUNCTION. For the VCR, press VCR/DVD

FUNCTION.

See “Operating a Cable Box” on page 60 and “Operating a VCR” on page 59. VCR functions with the TV remote control

Label video inputs to easily

See the instructions for setting up Video Labels on page 85. identify equipment connected to the TV

Two VCRs for Tape Editing

Connecting two VCRs lets you record from one VCR to the other. By

connecting them as shown below, you can view (monitor) what is

being recorded.

Using S VIDEO jacks? See page 21.

Cables are often

color-coded to connectors.

Connect red to red, white to white, etc.

Playback VCR

A/V cable

To connect two VCRs for tape editing

1 Use an A/V cable to connect the playback VCR’s A/V output

jacks to the TV’s A/V input jacks.

2 Use an A/V cable to connect the recording VCR’s A/V input

jacks to the TV’s MONITOR OUT jacks.

Recording VCR

A/V cable

SETUP SETUP SETUPSETUP SetupSETUP

Notes on Using This Connection

To Do This ... Do This ...

View (monitor) what is being recorded

Set up the TV remote control to operate the VCR(s)

Activate the TV remote control to operate the VCR(s)

Control VCR functions with the TV remote control

Label video inputs to easily identify equipment connected to the TV

Press TV/VIDEO repeatedly to select the VCR input (VIDEO 1 in the

illustration above).

If you have a non-Sony VCR, you must program the remote control. See

“Programming the Remote Control” on pages 49-50.

Press VCR/DVD FUNCTION.

See “Operating a VCR” on page 59.

See the instructions for setting up Video Labels on page 90.

SETUP Setup SETUPSETUP SETUPSETUP

Satellite Receiver To connect a satellite receiver

1 Connect the satellite antenna cable to the satellite receiver’s

Using S VIDEO jacks? See page 21.

satellite input jack.

2 Use an A/V cable to connect the satellite receiver’s A/V output

jacks to the TV’s A/V input jacks.

3 Connect a CATV cable from your cable or antenna to the TV’s

CABLE jack.

4 Run Auto Program, as described in “Setting Up the Channel List”

on page 43.

A/V cable

Satellite receiver

CATV cable

Satellite antenna cable

Cables are often

color-coded to connectors.

Connect red to red, white to white, etc.

SETUP SETUP SETUPSETUP SetupSETUP

Notes on Using This Connection

To Do This ... Do This ...

Watch the satellite receiver Press TV/VIDEO repeatedly to select the satellite receiver input

(VIDEO 1 in the illustration).

Set up the TV remote control to operate the satellite receiver

Activate the TV remote control to operate the satellite receiver

Control satellite receiver functions with the TV remote control

Label video inputs to easily identify equipment connected to the TV

If you have a non-Sony satellite receiver, you must program the remote control. See “Programming the Remote Control” on pages 49-50.

Press SAT/CABLE FUNCTION.

See “Operating a Satellite Receiver” on page 59.

See the instructions for setting up Video Labels on page 90.

SETUP Setup SETUPSETUP SETUPSETUP

+ 77 hidden pages