Sony HT-S200F Users guide [zh, en]

Download

Sound Bar

Operating Instructions GB

HT-S200F

WARNING

Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.

To reduce the risk of fire, do not cover the ventilation opening of the appliance with newspapers, tablecloths, curtains, etc. Do not expose the appliance to naked flame sources (for example, lighted candles).

To reduce the risk of fire or electric shock, do not expose this appliance to dripping or splashing, and do not place objects filled with liquids, such as vases, on the appliance.

The AC adapter is not disconnected from the mains as long as it is connected to the AC outlet, even if the unit itself has been turned off.

As the mai n plug o f AC p ower adapte r is used to disconnect the AC power adapter from the mains, connect it to an easily accessible AC outlet. Should you notice an abnormality in it, disconnect it from the AC outlet immediately.

For the AC adapter

Labels for AC adapter Model No. and Serial No. are located at the bottom of AC adapter.

Do not expose batteries or appliances with battery-installed to excessive heat, such as sunshine and fire.

Indoor use only.

Recommended cables

Properly shielded and grounded cables and connectors must be used for connection to host computers and/or peripherals.

For the Bar Speaker

The nameplate is located on the bottom of the Bar Speaker.

Table of Contents

About These Operating

Instructions ..............................3

What’s in the Box ..........................4

What You Can Do with the

System .....................................5

Guide to Parts and Controls ..........6

Connecting a TV

Connecting a TV with an HDMI Cable

Connecting Sony TV with the

BLUETOOTH Function

Wirelessly ...............................12

Mounting the Bar Speaker on a

Wall ........................................ 14

When the TV Remote Control does

not Work ................................ 16

Listening to the Sound

Listening to a TV and Other

Devices ...................................17

Listening to Music on a USB

Device .................................... 18

Selecting the Sound Effect

Adjusting the Sound ....................20

Listening to Music/Sound with the BLUETOOTH® Function

Listening to Music from a Mobile

Device ....................................22

Turning the System On by

Operating the BLUETOOTH

Device ....................................24

Turning the BLUETOOTH Function

Off ..........................................24

Startup Guide (separate



document)

Using the Various Functions

Using the Control for HDMI

Function .................................25

Using the “BRAVIA” Sync

Function .................................26

Notes on HDMI Connections ....... 27

Saving Power Consumption ........ 27

Troubleshooting

Troubleshooting ..........................28

Resetting the System ..................32

Additional Information

Specifications ...............................33

Playable Types of Files

(USB Input) .............................34

Supported Input Audio Formats

(TV Input) ...............................34

On BLUETOOTH

Communication .....................35

Precautions ..................................36

About These Operating Instructions

•The instructions in these Operating Instructions describe the controls on the remote control.

•Some illustrations are presented as conceptual drawings, and may be different from the actual products.

•The default settings are underlined on each feature description.

What’s in the Box

•Bar Speaker (1)

• AC power cord (mains lead) (1) –Taiwan models

– Models for other countries/regions

• Remote control (1)

• R03 (size AAA) battery (2)

• Optical digital cable (1)

• AC adapter (1)

• Cushion pads for wall mounting (2)

• WALL MOUNT TEMPLATE (1)

•Startup Guide

• Operating Instructions

What You Can Do with the System

“Listening to a TV and Other Devices” (page 17)

Blu-ray Disc™ player, cable box, satellite box, etc.

Connecting the TV (refer to “Startup Guide” (separate document))

“Using the Control for HDMI Function” (page 25) “Using the “BRAVIA” Sync Function” (page 26)

“Listening to Music on a USB Device” (page 18)

“Listening to Music from a Mobile Device” (page 22)

“Connecting Sony TV with the BLUETOOTH Function Wirelessly” (page 12)

Guide to Parts and Controls

Details are omitted from the illustrations.

Bar Speaker

Front

 Remote control sensor

Point the remote control at the remote control sensor to operate the system.

 (power) button

Turns on the system or sets it to standby mode.

 (input select) button

(page 17)

 BLUETOOTH button (page 22)

 +/– (volume) buttons  Indicators

For details, see “About the indicators on the Bar Speaker” (page 7).

About the indicators on the Bar Speaker

Lighting and flashing of the indicator(s) on the Bar Speaker indicate the input or status of the input device.

Indicators Status

• Lights: TV input is selected.

• Lights in blue: BLUETOOTH connection is established (BLUETOOTH input is selected).

• Flashes quickly in blue (about twice a second): During pairing standby status.

• Flashes slowly in blue (about once a second): BLUETOOTH connection is being attempted.

• Lights: USB input is selected.

• Flashes twice: The play mode is changed.

• Flashes three times first, then flashes slowly repeatedly: When connecting an unsupported device.

• Flashes repeatedly: While reading data of the connected USB device.

• Light: The system is connected to the TV with the BLUETOOTH function (TV input is selected).

The indicators flash when tu rning on/off the function setting or operating the remote control.

Indicators Status

• Flashes twice: One of the following functions is set to on. – Night mode (page 20) – Voice mode (page 20)

• Flashes once: The audio channel is set to Main (page 21), the sound mode is selected (page 20), or one of the following functions is set to off. – Night mode (page 20) – Voice mode (page 20)

• Flashes twice: One of the following functions is set to on. –Dolby DRC (page21) – Control for HDMI (page 25) – BLUETOOTH standby (page 24) – BLUETOOTH function (page 24) – Auto standby (page 27) – IR repeater (page 16) –Auto volume (page21) – Wall mount mode (page 14)

• Flashes once: The audio channel is set to Sub (page 21) or one of the following functions is set to off. –Dolby DRC (page21) – Control for HDMI (page 25) – BLUETOOTH standby (page 24) – BLUETOOTH function (page 24) – Auto standby (page 27) – IR repeater (page 16) –Auto volume (page21) – Wall mount mode (page 14)

Indicators Status

• Flash twice: The function that connects to the TV with the BLUETOOTH function is set to on (page 12).

• Flash once: The function that connects to the TV with the BLUETOOTH function is set to off (page 12).

• Flash once: The audio channel is set to Main/Sub (page 21).

• Flash quickly (about twice a second): The protection feature is activated (page 31).

• Flash slowly (about once a second): The system enters standby mode by the auto standby function (page 27).

The indicators flash while adjusting the volume level.

Indicators Status

• Flashes once: The volume level is low (1 - 20)./The level of the bass tone is set to -1 (Light) (page 21).

• Flash once: The volume level is medium (21 - 40)./The level of the bass tone is set to 0 (Normal) (page 21).

• Flash once: The volume level is high (41 - 49)./The level of the bass tone is set to +1 (Strong) (page 21).

• Flash repeatedly: The sound is muted.

• Flash twice: The volume level is set to maximum/minimum.

Tip

You can turn the indicators off by holding down AUTO SOUND for 5 seconds. Even if the indicators are turned off by using AUTO SOUND, if you operate the system, the indicators in relation to the operation light or flash.

Rear

 DC IN terminal  HDMI OUT (TV (ARC)) jack

Connect a TV that has an HDMI input jack with an HDMI cable. The system is compatible with Audio Return Channel (ARC). ARC is the function that sends TV so un d t o a n A V d evi ce su ch as the system from the TV’s HDMI jack.

 TV IN (OPTICAL) jack  (USB) port (page 18)  IR repeater (page 16)

Transmits the remote signal of the TV remote control to the TV.

 Subwoofer

Remote Control

Some buttons function differently depending on how long the button is pressed. The icons below indicate how long to press the button.

• : Press the button.

• : Press and hold the button for 5 seconds.

 INPUT (page 17)

Selects the playback source. When you press INPUT once, the current input indicator flashes. Press INPUT again to select the device you want. Each time you press INPUT, the input changes cyclically as follows. TV input BLUETOOTH input  USB input

 AUTO SOUND

: Selects AUTO SOUND for the

sound effect. (page 20)

: Turns on/off the indicators on

the Bar Speaker. (page 7)

 CINEMA

: Selects CINEMA for the sound

effect. (page 20)

: Turns on/off the auto standby

function. (page 27)

 VOICE

: Turns on/off the voice mode.

(page 20)

: Turns on/off the Control for

HDMI function. (page 25)

  (volume) +*/–

Adjusts the volume.

 BASS

: Adjusts the level of the bass

tone. (page 21)

: Turns on/off the wall mount

mode. (page 14)

 PLAY MODE (page 18)

Selects the play mode for USB playback.

 / (page 18)

Select the content on the TV screen for USB playback.

/ (previous/next)

(page 18, 22)

Pressing the button shortly goes to the beginning of the previous or next file. Pressing and holding searches backward or forward (rewind/fast forward).

 (power)

Turns on the system or sets it to standby mode.

 STANDARD

: Selects STANDARD for the

sound effect. (page 20)

: Turns on/off the IR repeater

function. (page 16)

 MUSIC (page 20)

: Selects MUSIC for the sound

effect. (page 20)

: Turns on/off the function that adjusts the volume level automatically. (page 21)

 NIGHT

: Turns on/off the night mode.

(page 20)

: Turns on/off the BLUETOOTH standby mode. (page 24)

  (muting)

Turns off the sound temporarily or turn on the sound.

 AUDIO*

: Selects the audio channel for Dolby Digital multiplex broadcast. (page 21)

: Turns on/off the Dolby DRC

function. (page 21)

 ENTER (page 18)

Plays the content that is selected by

/ for USB playback.

  (play/pause)* (page 18, 22)

Pauses or resumes playback.

*The AUDIO,  +, and  buttons have

a tactile dot. Use it as a guide during operation.

About the replacement of batteries for the remote control

When the system does not respond by operating with the remote control, replace two batteries with new batteries. Use R03 (size AAA) manganese batteries for replacement.

Connecting a TV

Blu-ray Disc player, cable box, satellite box, etc.

INPUT

BLUETOOTH button

connections and operations to listen to TV sound by connecting with an HDMI cable, refer to Startup Guide (separate document).

Connecting a TV with an HDMI Cable

Refer to Startup Guide (separate document).

Connecting Sony TV with the BLUETOOTH Function Wirelessly

When using Sony TV* with the BLUETOOTH function, you can listen to sound of the TV or device that is connected to the TV by connecting the system and TV wirelessly.

* The TV needs to be compatible with

A2DP (Advanced Audio Distribution Profile).

Connecting the System and TV Wirelessly

To connect the system and TV wirelessly, you need to perform pairing of the system and TV by using the BLUETOOTH function. Pairing is the process required to mutually register the information on BLUETOOTH devices to be connected wirelessly in advance.

Note

If connecting the system and TV by using the BLUETOOTH function, you cannot display the operation screen for the system such as the USB playback screen, and use the function of the system other than the function of listening to sound of the TV or device that is connected to the TV. To use all the functions of the system, connect the system and TV with an HDMI cable (not supplied). For details about

1 Press and hold the BLUETOOTH

button on the Bar Speaker and INPUT on the remote control simultaneously for 5 seconds.

The TV and BLUETOOTH indicators flash twice, the system enters the pairing mode, then the BLUETOOTH indicator flashes quickly.

2 On the TV, search the system by

performing the pairing operation.

The list of the BLUETOOTH devices that are searched appears on the TV screen. For the operation method to pair the BLUETOOTH device to the TV, refer to the operating instructions of the TV.

3 Pair the system and TV by

selecting “HT-S200F” from the list on the TV screen.

4 Make sure that the BLUETOOTH

and TV indicators on the Bar Speaker light.

A connection between the system and TV has been established and TV sound is output from the system. After pairing is completed, TV sound is output from the system automatically when the system is turned on.

Notes

• If the TV sound is not output from the system, press INPUT repeatedly to select

the TV input and check the status of the indicators on the Bar Speaker. – The BLUETOO TH and TV indicator s light:

The system and TV are connected and TV sound is output from the system.

– The BLUETOOTH indicator flashes

quickly: Perform pairing on the TV.

– The TV indicator lights: Perform steps

again from the start.

• When you connect the system and TV with an HDMI cable (not supplied), the BLUETOOTH connection is canceled. To connect the system and TV with the BLUETOOTH function again, disconnect the HDMI cable, then perform the connecting operation from the start.

• To pair the another TV after the first TV is paired, turn off the paired TV, then pair the new one by following the steps of a mobile device connection (page 22).

Listening to the Sound of the TV or Device that is Connected to the TV

You can turn the system on/off, adjust the volume, and mute the sound by using the TV remote control when connecting the TV to the system wirelessly.

1 Turn the TV on with the TV remote

control.

The system is turned on by interlocking with the TV power, and TV sound is output from the system.

2 Select the program or input of the

device by using the TV remote control.

The sound of the image displayed on the TV screen is output from the system.

3 Adjust the volume of the system

by using the TV remote control.

When pressing the mute button on the TV remote control, the sound is muted temporarily.

Tip



 +/–



STANDARD AUTO SOUND

MUSIC CINEMA

NIGHT VOICE

BASS

When the TV is turned off, the system is also turned off by interlocking with the TV power.

About operations with the remote control that is supplied with the system

You can use the following buttons. You can adjust the level of the bass tone and sound quality in addition to turning the system on/off and adjusting volume that can be operated by the TV remote control.

Note

If you select the USB input on the remote control supplied with the system, the TV sound is not output from the system. To output the TV sound, press INPUT on the remote control to select the TV input.

Mounting the Bar Speaker on a Wall

You can mount the Bar Speaker on a wall.

Notes

• Prepare screws (not supplied) that are suitable for the wall material and strength. As a plasterboard wall is especially fragile, attach the screws securely in the wall beam. Install the speakers horizontally, hung by screws in studs in a continuous flat section of the wall.

• Have the installation done by a Sony dealer or licensed contractor and pay special attention to safety during the installation.

• Sony shall not be held responsible for accidents or damage caused by improper installation, insufficient wall strength, improper screw installation or natural disaster, etc.

1 Prepare two screws (not supplied)

Hole on the rear of the Bar Speaker

4mm

More than 30 mm

5 mm

10 mm

Center of the TV

WALL MOUNT TEMPLATE

Adhesive tape, etc.

Screws

Marks ()

5 mm to 6mm

200 mm

Cushion pad

that are suitable for the wall mount holes on the rear of the Bar Speaker.

2 Stick WALL MOUNT TEMPLATE

(supplied) on a wall.

3 Fasten the screws into the marks

() on SCREW LINE () of WALL MOUNT TEMPLATE as in the illustration below.

4 Remove WALL MOUNT TEMPLATE. 5 Attach the cushion pads

(supplied) below the holes on the rear of the Bar Speaker.

1 Align TV CENTER LINE () of

WALL MOUNT TEMPLATE with the center line of your TV.

2 Align TV BOTTOM LINE () of

WALL MOUNT TEMPLATE with the bottom of your TV, then stick WALL MOUNT TEMPLATE on a wall by using a commercially available adhesive tape, etc.

6 Hang the Bar Speaker on the

screws.

Align the holes of the rear of the Bar Speaker with the screws, then hang the Bar Speaker on the two screws.

When the TV Remote Control does not Work

When the Bar Speaker obstructs the remote control sensor of the TV, the TV remote control may not work. In that case, enable the IR repeater function of the system. You can control the TV with the TV remote control by sending the remote signal from the rear of the Bar Speaker.

Press and hold STANDARD for 5 seconds to set the function to on or off.

7 Press and hold BASS for 5 seconds

to set the wall mount mode to on.

The USB indicator flashes twice. You can optimize the sound of the system that is mounted on a wall.

Notes

• When sticking WALL MOUNT TEMPLATE, smooth it out fully.

• To set the wall mount mode to off, press and hold BASS for 5 seconds. The USB indicator flashes once.

IR repeater on

The USB indicator flashes twice.

IR repeater off

The USB indicator flashes once.

Notes

• Be sure to check that the TV remote control cannot control the TV, and then set the IR repeater function to on. If it is set to on when the remote control can control the TV, appropriate operation may not be obtained because of the interference between the direct command from the remote control and the command via the Bar Speaker.

• On some TVs, this function may not work correctly. In this case, place the Bar Speaker slightly further away from the TV.

Listening to the Sound

INPUT

 +/–

BASS

Listening to a TV and Other Devices

1 Press INPUT repeatedly.

When you press INPUT once, the current input indicator flashes. Press INPUT again to select the device you want. The indicator of the selected device lights up. Each time you press INPUT, the input changes cyclically as follows. TV input  BLUETOOTH input  USB input

TV input

• TV that is connected to the TV IN (OPTICAL) jack

• TV compatible with the Audio Return Channel (ARC) function that is connected to the HDMI OUT (TV (ARC)) jack

When you connect the TV to both the HDMI OUT (TV (ARC)) and TV IN (OPTICAL) jacks, the jack for audio input is selected depending on which audio signal is input first.

BLUETOOTH input

BLUETOOTH device that supports A2DP For details, see “Listening to Music/ Sound with the BLUETOOTH® Function” (page 22).

USB input

USB device that is connected to the

(USB) port For details, see “Listening to Music on a USB Device” (page 18).

2 Adjust the volume.

• Adjust the volume by pressing 

+/– on the remote control.

• Adjust the level of the bass tone

by pressing BASS on the remote control (page 21).

Tip

You can also select the input by pressing

on the Bar Speaker.

Listening to Music on a

ENTER

PLAY MODE

 +/–



/

INPUT

/

BASS

USB Device

You can play music files stored on a connected USB device. For playable types of files, see “Playable Types of Files (USB Input)” (page 34).

Notes

• To view the USB content list on the TV screen, make sure you connect the system to the TV using an HDMI cable.

• Change the input of the TV to the input to which the Bar Speaker is connected.

1 Connect the USB device to the

(USB) port.

2 Press INPUT repeatedly to select

“USB.”

The USB indicator lights up and the USB content list appears on the TV screen.

3 Press / to select the content

you want, then press ENTER.

The selected content starts playing.

4 Press PLAY MODE repeatedly to

select the play mode you want.

• None: Plays back all tracks.

• [ ] (Repeat One): Repeats one track.

•

[ ] (Repeat Folder): Repeats all

tracks in a folder.

[ ] (Random): Repeats all tracks

• in a folder in random order.

• [ ] (Repeat All): Repeats all tracks.

The USB indicator flashes twice each time you press PLAY MODE.

5 Adjust the volume.

• Adjust the volume by pressing  +/– on the remote control.

• Adjust the level of the bass tone by pressing BASS on the remote control (page 21).

Other operations

To Do this

Pause or resume playback

Select the previous or next track

Search backward or forward (rewind/fast forward)

Notes

• Do not remove the USB device during operation. To avoid data corruption or damage to the USB device, turn the system off before connecting or removing the USB device.

• The USB indicator flashes three times first, then flashes slowly repeatedly if you connect an unsupported USB device.

Press .

Press /.

Press and hold /.

Information of USB Device on the TV Screen

 Playing time  Total playing time  Bit rate  Playback status  Rewind/fast forward speed  Repeat play status  Selected file index/Total files in the

folder

The following messages appear on the TV screen.

• [File Unsupported] Appears for 1 second at the bottom left side when unsupported file is skipped.

• [Device Not Support] – A USB device is not supported. – Device inserted is a non-USB device,

a bad USB device, or a USB device that has no files on it.

•[No USB] No USB device is inserted.

•[Waiting] The system is searching the USB device.

• [This device is empty] There are no playable files in the USB device.

Notes

• Depending on the playback source, some

information may not be displayed.

• Depending on the play mode, the

information displayed may be different.

Selecting the Sound Effect

STANDARD

AUTO SOUND MUSIC

CINEMA

STANDARD

Sound effects are optimized for each individual source.

Adjusting the Sound

Enjoying the Sound Effect that is Tailored to Sound Sources (Sound Mode)

You can easily enjoy pre-programmed sound effects that are tailored to different kinds of sound sources.

Press AUTO SOUND, CINEMA, MUSIC, or STANDARD to select the sound mode.

When selecting the sound mode, the TV indicator flashes once.

AUTO SOUND

You can enjoy the sound with Sonyrecommended sound mode. The sound mode is automatically optimized according to playback content and function.

CINEMA

Sounds are played back with surround effects, and they are realistic and powerful, making them suitable for movies.

MUSIC

Sound effects are optimized for listening to music.

Enjoying Clear Sound with Low Volume at Midnight (NIGHT)

Sound is output at low volume with minimum loss of fidelity and clarity of dialog.

Press NIGHT to set the function to on or off.

Night mode on

The TV indicator flashes twice.

Night mode off

The TV indicator flashes once.

Note

When you turn the system off, the night mode is set to off automatically.

Making Dialogs Clearer (VOICE)

You can make dialogs clearer by setting the voice mode to on.

Press VOICE to set the function to on or off.

Voice mode on

The TV indicator flashes twice.

Voice mode off

The TV indicator flashes once.

Making Sound with Low Volume Easy to Hear by Compressing Dynamic Range

This function works only when playing the Dolby Digital signal of the device that is connected to the TV IN (OPTICAL)/HDMI OUT (TV (ARC)) jack. When you set Dolby DRC (Dynamic Range Control) to on, dynamic range of the audio signal (range between the maximum and minimum volume) is compressed and sound with low volume is easy to hear.

Press and hold AUDIO for 5 seconds to set the function to on or off.

Dolby DRC on

The USB indicator flashes twice.

Dolby DRC off

The USB indicator flashes once.

Enjoying Multiplex Broadcast Sound (AUDIO)

You can enjoy multiplex broadcast sound when the system receives a Dolby Digital multiplex broadcast signal.

Press AUDIO repeatedly.

The channel changes cyclically as follows.

 Sub  Main/Sub

Main

Outputs only the main channel. The TV indicator flashes once.

Sub

Outputs only the sub channel. The USB indicator flashes once.

Main/Sub

Main sound is output from the left speaker and sub sound is output from the right speaker. The TV and USB indicators flash once.

Note

To receive a Dolby Digital signal, you need to connect a TV or other devices to the TV IN (OPTICAL) jack with the optical digital cable (supplied) or the HDMI OUT (TV (ARC)) jack with an HDMI cable (not supplied).

Adjusting the Volume for the Connected Device Automatically

You can adjust the volume automatically depending on the input signal or content from a connected device by setting the auto volume function to on.

Press and hold MUSIC for 5 seconds to set the function to on or off.

Auto volume function on

The USB indicator flashes twice.

Auto volume function off

The USB indicator flashes once.

Adjusting the Level of the Bass Tone

Press BASS repeatedly.

The level of the bass tone changes cyclically as follows.

 +1  0  -1  0...

0 (Normal)

The TV and BLUETOOTH indicators flash once.

+1 (Strong)

All the indicators flash once.

-1 (Light)

The TV indicator flashes once.

Note

When the input source does not contain much bass sound, such as in TV programs, the bass sound from the subwoofer may be difficult to hear.

Listening to Music/Sound with the

BLUETOOTH indicator

BLUETOOTH button

BLUETOOTH® Function

Listening to Music from a Mobile Device

You can listen to music stored on a mobile device such as a smartphone or tablet via a wireless connection by connecting the system and the mobile device with the BLUETOOTH function. When connecting to the mobile device with the BLUETOOTH function, you can operate by simply using the supplied remote control without turning the TV on.

Listening to Music by Pairing with a Mobile Device

1 Press and hold the BLUETOOTH

button on the Bar Speaker for 5 seconds.

The system enters the pairing mode and the BLUETOOTH indicator flashes quickly.

If pairing is not performed for 5 minutes after the system enters the pairing mode, the pairing mode is canceled. In this case, perform pairing from the start.

2 On the mobile device, search the

system by performing the pairing operation.

The list of the BLUETOOTH devices that are searched appears on the screen of the mobile device. For the operation method to pair the BLUETOOTH device to the mobile device, refer to the operating instructions of the mobile device.

3 Pair the system and mobile device

by selecting “HT-S200F” from the list on the screen of the mobile device.

If a Passkey is requested, enter “0000.”

4 Make sure that the BLUETOOTH

indicator on the Bar Speaker lights in blue.

A connection between the system and mobile device has been established.

5 Start audio playback with the

music app on the connected mobile device.

Sound is output from the Bar Speaker.

6 Adjust the volume.

• Adjust the volume by pressing 

+/– on the remote control.

• Adjust the level of the bass tone by pressing BASS on the remote control (page 21).

•  and / on the remote control can be used for the BLUETOOTH function. (Rewind and fast forward are also available.)

Notes

• You can pair up to 10 BLUETOOTH devices. If an 11th BLUETOOTH device is paired, the least recently connected device will be replaced by the new one. If the Sony TV with the BLUETOOTH

function is paired, it is counted as the

INPUT

 +/–

BASS



/

BLUETOOTH device.

• Perform pairing for the second and subsequent mobile devices.

Tips

• You can check the connection status of the BLUETOOTH function by checking the BLUETOOTH indicator status (page 7).

• While the BLUETOOTH input is being selected, the system enters the pairing mode by pressing the BLUETOOTH button on the Bar Speaker shortly.

• While the BLUETOOTH input is not selecting, the system automatically reconnects to the BLUETOOTH device it was most recently connected to by pressing the BLUETOOTH button on the Bar Speaker shortly.

Listening to Music from the Paired Mobile Device

1 Turn the BLUETOOTH function of

the mobile device to on.

2 Press INPUT repeatedly to select

the BLUETOOTH input or press the BLUETOOTH button on the Bar Speaker shortly.

The BLUETOOTH indicator flashes and the system automatically reconnects to the BLUETOOTH device it was most recently connected to.

3 Make sure that the BLUETOOTH

indicator lights in blue.

A connection between the system and mobile device has been established.

4 Start audio playback with the

music app on the connected mobile device.

Sound is output from the Bar Speaker.

5 Adjust the volume.

• Adjust the volume by pressing 

+/– on the remote control.

• Adjust the level of the bass tone by pressing BASS on the remote control (page 21).

•  and / on the remote control can be used for the BLUETOOTH function. (Rewind and fast forward are also available.)

Turning the System On by Operating the BLUETOOTH Device

When the system has pairing information, you can turn the system on and listen to music from a BLUETOOTH device even when the system is in standby mode by setting the BLUETOOTH standby mode to on.

Press and hold NIGHT for 5 seconds to set the function to on or off.

BLUETOOTH standby mode on

The USB indicator flashes twice.

BLUETOOTH standby mode off

The USB indicator flashes once.

Note

While the BLUETOOTH standby mode is on, standby power consumption increases.

Turning the BLUETOOTH Function Off

You can turn the BLUETOOTH function off.

Press and hold , , and – on the Bar Speaker for 10 seconds to set the function to on or off.

BLUETOOTH function on

The USB indicator flashes twice.

BLUETOOTH function off

The USB indicator flashes once.

Note

When the BLUETOOTH function is set to off, the BLUETOOTH input is skipped while selecting input by pressing INPUT.

Using the Various Functions

Using the Control for HDMI Function

Connec ting a dev ice such as a T V or Bluray Disc player compatible with the Control for HDMI function* using an HDMI cable (not supplied) enables you to easily operate the device by using a TV or Blu-ray Disc player remote control. The following functions can be used with the Control for HDMI function.

• System Power Off function

• System Audio Control function

•Audio Return Channel

• One-Touch Play function

Note

These functions may work with devices other than those manufactured by Sony, but operation is not guaranteed.

* Control for HDMI is a standard used by

CEC (Consumer Electronics Control) for allowing HDMI (High-Definition Multimedia Interface) devices to control each other.

Preparing to Use the Control for HDMI Function

Press and hold VOICE for 5 seconds to set the function to on or off.

Tip

If you enable the Control for HDMI (“BRAVIA” sync) function when using a TV manufactured by Sony, the Control for HDMI function of the system is also enabled automatically.

System Power Off Function

When you turn off the TV, the system will turn off automatically.

System Audio Control Function

If you turn on the system while you are watching the TV, the TV sound will be output from the speakers of the system. The volume of the system can be adjusted using the TV remote control. If the TV sound was output from the speakers of the system the previous time you watched the TV, the system will be turned on automatically when you turn on the TV again. Operations can also be made by the TV’s menu. For details, refer to the operating instructions of your TV.

Notes

• The number for the sy stem’s volume level is displayed on the TV screen depending on the TV.

• Depending on the settings of the TV, the System Audio Control function may not be available. For details, refer to the operating instructions of your TV.

Control for HDMI function on

The USB indicator flashes twice.

Control for HDMI function off

The USB indicator flashes once.

Enable the Control for HDMI function settings for the TV and other devices connected to the TV.

Audio Return Channel

If the system is connected to a TV’s HDMI IN jack compatible with Audio Return Channel (ARC), you can listen to TV sound from the speakers of the system without connecting an optical digital cable.

Note

If the TV is not compatible with Audio Return Channel, the optical digital cable (supplied) needs to be connected (refer to the supplied Startup Guide).

One-Touch Play Function

When you play content on a device (Bluray Disc player, “PlayStation connected to the TV, the system and TV are turned on automatically, the inpu t of the system is switched to “TV” input, and sound is output from the speakers of the system.

Notes

• If the TV sound was output from the speakers of the TV the previous time you watched the TV, the system does not turn on and the sound and picture are output from the TV even if device content is played.

• Depending on the TV, the beginning part of content being played may not play correctly.

4,” etc.)

Using the “BRAVIA” Sync Function

In addition to the Control for HDMI function, you can also use the following functions on devices compatible with the “BRAVIA” sync function.

• Sound mode/Scene Select Function

• Home Theatre Control

Note

These functions are proprietary functions of Sony. This function cannot operate with products other than those manufactured by Sony.

Sound mode/Scene Select Function

The sound mode of the system is automatically switched according to the setting of the TV’s Scene Select function or sound mode. For details, refer to the operating instructions of your TV. Set the sound mode to “AUTO SOUND” (page 20).

Home Theatre Control Function

When using a TV compatible with the Home Theatre Control function, setting the system, setting the sound mode settings, input switching, etc. can be done without switching the TV input. This function can b e used when the TV is connected to the Internet. For details, refer to the operating instructions of your TV.

Notes on HDMI Connections

Saving Power Consumption

• Use an HDMI-authorized cable.

• We recommend using a Sony High Speed HDMI Cable with Ethernet with the Cable Type Logo.

• We do not recommend using an HDMI-DVI conversion cable.

• Audio signals (sampling frequency, bit length, etc.) transmitted from an HDMI jack may be suppressed by the connected device.

To use the system while saving power consumption, change the following settings.

Turn the System Off by Detecting the Using State

When you set the auto standby function to on, the system enters standby mode automatically when you do not operate the system for about 20 minutes and the system is not receiving an input signal.

Press and hold CINEMA for 5 seconds to set the function to on or off.

Auto standby on

The USB indicator flashes twice.

Auto standby off

The USB indicator flashes once.

Saving Power in Standby Mode

To save power consumption during the standby mode, set the BLUETOOTH standby mode (page 24) and Control for HDMI function (page 25) to off. The default settings for them are on.

Troubleshooting

If you experience any of the following difficulties while using the system, use this troubleshooting guide to help remedy the problem before requesting repairs. Should any problem persist, consult your nearest Sony dealer.

Power

The system does not power up.

 Check that the AC power cord (mains

lead) and AC adapter are connected securely.

 Disconnect the AC power cord (mains

lead) from the wall outlet (mains), and then reconnect after several minutes.

The system is turned off automatically.

 The auto standby function is working.

Set the auto standby function to off (page 27).

The system does not turn on even when the TV is turned on.

 Set the Control for HDMI function to

on (page 25). The TV must support the Control for HDMI function. For details, refer to the operating instructions of your TV.

 Check the speaker settings of the TV.

The system power syncs with the speaker settings of the TV. Fo r details, refer to the operating instructions of your TV.

 If the sound was output from the

speakers of the TV the previous time, the system does not turn on even when the TV is turned on.

The system turns off when the TV is turned off.

 Check the setting of the Control for

HDMI function (page 25). When the Control for HDMI function is set to on and the input of the system is the TV input, the system turns off automatically when you turn off the TV.

The system does not turn off even when the TV is turned off.

 Check the setting of the Control for

HDMI function (page 25). When you turn off the TV, the system turns off automatically only if the input of the system is the TV input. The TV must support the Control for HDMI function. For details, refer to the operating instructions of your TV.

Picture

There is no picture or the picture is not output correctly.



Select the appropriate input (page 17).

 When there is no picture while TV

input is selected, select the TV channel that you want using the TV remote control.

 Disconnect the HDMI cable, then

connect it again. Make sure that the cable is firmly inserted.

Sound

No TV sound is output from the system.

 Check the type and connection of the

HDMI cable or optical digital cable that is connected to the system and the TV (refer to the supplied Startup Guide).

 Disconnect the cables that are

connected between the TV and the system, then connect them firmly again. Disconnect the AC power cords

of the TV and the system from the AC outlets (mains), then connect them again.

 When the system and TV are

connected with an HDMI cable, check the following. – The HDMI jack of the connected TV

is labeled with “ARC.”

– The Control for HDMI function of the

TV is set to on.

– On the system, the Control for HDMI

function is set to on (page 25).

If your TV is not compatible with Audio



Return Channel, connect the optical digital cable (supplied) (refer to the supplied Startup Guide). If the TV is not compatible with Audio Return Channel, TV sound will not be output from the system even if the system is connected to the TV’s HDMI IN jack.

 If the sound of the device that is

connected to the optical input jack of the TV is not output, try the following. – Connect the cable box or satellite

box directly to the TV IN (OPTICAL) jack of the system.

 Press INPUT repeatedly to select the

TV input (page 17).

 Increase the volume on the TV or

cancel muting.

 Depending on the order in which you

connect the TV and the system, the system may be muted. If this happens, turn on the TV first, then the system.

 Set the speakers setting of the TV

(BRAVIA) to Audio System. Refer to the operating instructions of your TV regarding how to set the TV.

 Check the sound output of the TV.

Refer to the operating instructions of the TV for the TV settings.

 The system supports t he Dolby Digital

and PCM audio formats (page 34). When you playback an unsupported format, set the digital audio out setting of the TV (BRAVIA) to “PCM.” For details, refer to the operating instructions of your TV.

The sound is output from both the system and the TV.

 Mute the sound of the system or the

TV.

No sound or only a very low-level sound of the device connected to the system is heard from the system.

 Press  + and check the volume

level (page 10).

 or  + to cancel the muting

 Press

function (page 10).

 Make sure the input source is

selected correctly. You should try other input sources by pressing INPUT repeatedly (page 17).

 Check that all the cables and cords of

the system and the connected device are firmly inserted.

 If the connected device supports up-

sampling feature, you need to turn it off.

The surround effect cannot be obtained.

 Depending on the input signal and

the sound mode setting, surround sound processing may not work effectively. The surround effect may be subtle, depending on the program or disc.

 To play multi channel audio, check

the digital audio output setting on the device connected to the system. For details, refer to the operating instructions supplied with the connected device.

Subwoofer

No sound or only very low-level sound is heard from the subwoofer.

 Press BASS repeatedly to adjust the

level of the bass tone (page 21).

 If the input sources contain very little

bass sound components (i.e., a TV broadcast), the sound from the

subwoofer may be difficult to hear. Play the built-in de monstration music by following the steps below and check that the sound is output from the subwoofer.  Press and hold on the Bar

Speaker for 5 seconds. The built-in demonstration music is played.

 Press again.

The built-in demonstration music is canceled and the system returns to the previous status.

 Set the night mode to off. For details,

see “Enjoying Clear Sound with Low Volume at Midnight (NIGHT)” (page 20).

 The subwoofer is on the bottom of

the Bar Speaker. Make sure not to hit obstacles on the subwoofer.

USB Device Connection

The USB device is not recognized.

 Try the following:

 Turn the system off.  Remove and reconnect the USB

device.

 Turn the system on.

 Make sure that the USB device is

securely connected to the (USB) port (page 18).

 Check to see if the USB device or a

cable is damaged.

 Make sure that the USB device is on.  If the USB device is connected via a

USB hub, disconnect it and connect the USB device directly to the system.

Mobile Device Connection

BLUETOOTH connection cannot be completed.

 Make sure that the BLUETOOTH

indicator on the Bar Speaker is lit (page 6).

 Make sure the BLUETOOTH device to

be connected is turned on and the BLUETOOTH function is enabled.

 Bring the BLUETOOTH device close to

the system.

 Pair this system and the BLUETOOTH

device again. You may need to cancel the pairing with this system using your BLUETOOTH device first.

 If the BLUETOOTH function is set to

off, set it to on (page 24).

Pairing cannot be achieved.

 Bring the BLUETOOTH device close to

the system.

 Make sure this syste m is not receiving

interference from a wireless LAN device, other 2.4 GHz wireless devices, or a microwave oven. If a device that generates electromagnetic radiation is nearby, move the device away from this system.

 Pairing may not be possible if other

BLUETOOTH devices are present around the system. In this case, turn off the other BLUETOOTH devices.

Sound of the connected BLUETOOTH mobile device is not output from the system.

 Make sure that the BLUETOOTH

indicator on the Bar Speaker is lit (page 6).

 Bring the BLUETOOTH device close to

the system.

 If a device that generates

electromagnetic radiation, such as a wireless LAN device, other BLUETOOTH devices, or a microwave oven is nearby, move the devic e away from this system.

 Move the USB 3.0 device and its cable

away from this system.

 Remove any obstacle between this

system and the B LUETOOTH device or move this system away from the obstacle.

 If the system is installed under the TV,

move the system away from the TV.

 Reposition the connected

BLUETOOTH device.

 Switch the wireless LAN frequency of

any nearby wireless LAN router or PC to 5 GHz range.

 Increase the volume on the

connected BLUETOOTH device.

The sound is not in sync with the image.

 When you are watching movies, you

may hear the sound with a slight delay from the image.

Remote Control

The remote control of this system does not function.

 Point the remote control at the

remote control sensor on the Bar Speaker (page 6).

 Remove any obstacles in the path

between the remote control and the system.

 Replace both batteries in the remote

control with new ones, if they are weak.

 Make sure you are pressing the

correct button on the remote control (page 10).

The TV remote control does not work.

 Install the Bar Speaker so that it does

not obstruct the remote control sensor of the TV.

 This problem might be solved by

enabling the IR repeater function (page 16).

Others

The Control for HDMI function does not work properly.



Check the connection with the system (refer to the supplied Startup Guide).

 Enable the Control for HDMI function

on the TV. For details, refer to the operating instructions of your TV.

 Wait a while, and then try again. If

you unplug the system, it will take a while before operations can be made. Wait for 15 seconds or longer, and then try again.

 Make sure the devices connected to

the system support the Control for HDMI function.

 Enable the Control for HDMI function

of the devices connected to the system. For details, refer to the operating instructions of your device.

 The type and number of devices that

can be controlled by the Control for HDMI function is restricted by the HDMI CEC standard as follows: – Recording devices (Blu-ray Disc

recorder, DVD recorder, etc.): up to 3 devices

– Playback devices (Blu-ray Disc

player, DVD player, etc.): up to 3 devices

– Tuner-related devices: up to 4

devices

– Audio system (receiver/

headphone): up to 1 devi ce (used by this system)

All indicators on the Bar Speaker flash for 10 seconds and the system is turned off.

 The protection feature is activated.

Disconnect the AC power cord (mains lead) and check the items below. – Make sure that the ventilations of

the Bar Speaker are not covered and turn on the system after a while.

– When the system is using the USB

connection, remove the USB device and turn on the system. If the system operates properly, the current of the connected USB device is over the maximum output current of the system 500 mA, or the USB device may have an abnormality.

Sensors of the TV do not work properly.

 The Bar Speaker may block some

sensors (such as the brightness sensor), the remote control receiver of your TV or the emitter for 3D glasses (infrared transm ission) of a 3D TV that supports the infrared 3D glass system, or wireless communication. Move the Bar Speaker away from the TV within a range that allows those parts to operate properly. For the locations of the sensors and remote control receiver, refer to the operating instructions supplied with the TV.

The system does not work properly.

 The system may be in demo mode. To

cancel demo mode, reset the system. Press and hold – (volume) and  (power) on the Bar Speaker for more than 5 seconds (page 32).

When you change to the TV input from the USB input by pressing INPUT, the message appears.

Resetting the System

If the system still does not operate properly, reset the system as follows.

1 Press and hold – (volume) and 

(power) on the Bar Speaker for more than 5 seconds.

All indicators on the Bar Speaker flash 3 times, and the settings return to their initial status.

2 Disconnect the AC power cord

(mains lead).

3 Connect the AC power cord (mains

lead), then press  to turn on the system.

Tip

The default settings are underlined on each feature description.

* This screen is an example for English.

 Select the TV program by using the TV

remote control.

Additional Information

Specifications

Amplifier section

POWER OUTPUT (rated)

Front L + Front R: 20 W + 20 W (at 4 ohms, 1 kHz, 1% THD)

POWER OUTPUT (reference)

Front L/Front R speaker: 25 W (per channel at 4 ohms, 1 kHz) Subwoofer: 30 W (at 4 ohms, 100 Hz)

Inputs

TV IN (OPTICAL) USB

Outputs

HDMI OUT (TV (ARC))

USB section

(USB) port:

Type A (For connecting USB memory)

BLUETOOTH section

Communication system

BLUETOOTH Specification version 4.2

Output

BLUETOOTH Specification Power Class 1

Maximum communication range

Line of sight approx. 25 m

Frequency band

2.4 GHz band (2.4000 GHz -

2.4835 GHz)

Modulation method

FHSS (Freq Hopping Spread Spectrum)

Compatible BLUETOOTH profiles

A2DP (Advanced Audio Distribution Profile) AVRCP (Audio Video Remote Control Profile)

Supported Codec

SBC

Transmission range (A2DP)

20 Hz - 20,000 Hz (Sampling frequency 32 kHz, 44.1 kHz, 48 kHz)

The actual range will vary depending on factors such as obstacles between

devices, magnetic fields around a microwave oven, static electricity, cordless phone use, reception sensitivity, the operating system, software applications, etc.

BLUETOOTH standard profiles indicate the purpose of BLUETOOTH communication between devices.

Codec: Audio signal compression and conversion format

Abbreviation for Subband Codec

Speaker section

Speaker system

2-Way 3 Drivers Speaker System, Bass reflex

Speaker

Front L/Front R speaker: 46 mm cone type Subwoofer: 70 mm cone type

General

Power requirements

DC 19.5 V (using the supplied AC adapter connected to AC 100 V - 24 0 V, 50 Hz/60Hz power supply)

Power consumption

On: 25 W Standby mode: 0.5 W or less (Power Saving mode) (When Control for HDMI function and BLUETOOTH Standby mode are set to off) Standby mode: 2 W or less* (When Control for HDMI function and BLUETOOTH Standby mode are set to on)

* The system will automatically enter

Power saving mode when there is no HDMI connection and no BLUETOOTH pairing history.

Dimensions* (approx.) (w/h/d)

580 mm × 64 mm × 95 mm

* Not including projection portion

Mass (approx.)

2.3 kg

Design and specifications are subject to change without notice.

Playable Types of Files (USB Input)

Supported Input Audio Formats (TV Input)

Codec Extension

MP3 (MPEG-1 Audio Layer III)

WMA9 Standard .wma

LPCM .wav

Notes

• Some files may not play depending on

the file format, the file encoding, or the recording condition.

• Some files edited on a PC may not play.

• The system does not play coded files such

as DRM and Lossless.

• The system can recognize the following

files or folders in USB devices: – folder paths up to 128 characters long

for FAT16/32 or 124 characters long for NTFS

– up to 200 folders (including empty

folder and root folder)

– up to 200 audio files/folders in each

folder

• Some USB devices may not work with this

system.

• The system can recognize Mass Storage

Class (MSC) devices.

.mp3

Audio formats supported by this system are as follows.

•Dolby Digital

•Linear PCM 2ch

On BLUETOOTH Communication

• BLUETOOTH devices should be used within approximately 10 meters (33 feet) (unobstructed distance) of each other. The effective communication range may become shorter under the following conditions. – When a person, metal object, wall or

other obstruction is between the devices with a BLUETOOTH connection

– Locations where a wireless LAN is

installed

– Around microwave ovens that are in

use

– Locations where other

electromagnetic waves occur

• BLUETOOTH devices and wireless LAN (IEEE 802.11b/g/n) use the same frequency band (2 .4 GHz). When using your BLUETOOTH device near a device with wireless LAN capability, electromagnetic interference may occur. This could result in lower data transfer rates, noise, or inability to connect. If this happens, try the following remedies: – Use this system at least 10 meters

(33 feet) away from the wireless LAN device.

– Turn off the power to the wireless

LAN device when using your BLUETOOTH device within 10 meters (33 feet).

– Install this system and BLUETOOTH

device as closer to each other as possible.

• The radio waves broadcast by this system may interfere with the operation of some medical devices. Since this interference may result in malfunc tion, always t urn off the po wer o n th is sy st em an d B LU ET OO TH de vi ce in the following locations:

– I n hospitals, on trains, in airplanes, at

gas stations, and any place where flammable gasses may be present

– Near automatic doors or fire alarms

• This system supports security functions that comply with the BLUETOOTH specification to ensure secure connection during communication using BLUETOOTH technology. However, this security may be insufficient depending on the setting contents and other factors, so always be careful when performing communication using BLUETOOTH technology.

• Sony cannot be held liable in any way for damages or other loss resulting from information leaks during communication using BLUETOOTH technology.

• BLUETOOTH communication is not necessarily guaranteed with all BLUETOOTH devices that have the same profile as this system.

• BLUETOOTH devices connected with this system must comply with the BLUETOOTH specification prescribed by the Bluetooth SIG, Inc ., and must be certified to comply. However, even when a device complies with the BLUETOOTH specification, there may be cases where the characteristics or specifications of the BLUETOOTH device make it impossible to connect, or may result in different control methods, display or operation.

• Noise may occur or the audio may cut off depending on the BLUETOOTH device connected with this system, the communications environment, or surrounding conditions.

If you have any questions or problems concerning your system, please consult your nearest Sony dealer.

Precautions

On safety

• Should any solid object or liquid fall into the system, unplug the system and have it checked by qualified personnel before operating it any further.

• Do not climb on the Bar Speaker, as you may fall down and injure yourself, or system damage may result.

On power sources

• Before operating the system, check that the operating voltage is identical to your local power supply. The operating voltage is indicated on the nameplate on the bottom of the Bar Speaker.

• If you are not going to use the system for a long time, be sure to disconnect the system from the wall outlet (mains). To disconnect the AC power cord (mains lead), grasp the plug itself; never pull the cord.

• One blade of the plug is wider than the other for the purpose of safety and will fit into the wall outlet (mains) only one way. If you are unable to insert the plug fully into the outlet, contact your dealer.

• AC power cord (mains lead) must be changed only at a qualified service shop.

On heat buildup

Although the system heats up during operation, this is not a malfunction. If you continuously use this system at high volume, the system temperature at the rear and bottom rises considerably. To avoid burning yourself, do not touch the system.

On placement

• Place the system in a location with adequate ventilation to prevent heat buildup and prolong the life of the system.

• Do not place the system near heat sources or in a place subject to direct

sunlight, excessive dust, or mechanical shock.

• Do not place anything on the top of the Bar Speaker.

• If the system is being used in combination with a TV, VCR, or tape deck, noise may result and picture quality may suffer. In such a case, place the system away from the TV, VCR, or tape deck.

• Use caution when placing the system on a surface that has been specially treated (with wax, oil, polish, etc.), as staining or discoloration of the surface may result.

• Take care to avoid any possible injury from the corners of the Bar Speaker.

• When installing the Bar Speaker, make sure not to da mage the subwoofer on the bottom of the Bar Speaker.

On operation

Before connecting other equipment, be sure to turn off and unplug the system.

If you encounter color irregularity on a nearby TV screen

Color irregularities may be observed on certain types of TV.

• If color irregularity is observed... Turn off the TV, then turn it on again after 15 to 30 minutes.

• If color irregularity is observed again... Place the system further away from the TV.

On cleaning

Clean the system with a soft, dry cloth. Do not use any type of abrasive pad, scouring powder, or solvent such as alcohol or benzine.

If you have any question or problem concerning your system, please consult your nearest Sony dealer.

Copyrights and Trademarks

This system incorporates Dolby* Digital.

* Manufactured under license from Dolby

Laboratories. Dolby, Dolby Audio and the double-D symbol are trademarks of Dolby Laboratories.

The BLUETOOTH registered trademarks owned by Bluetooth SI G, Inc . an d a ny u se of s uch ma rks by S on y Corporation is under license. Other trademarks and trade names are those of their respective owners.

This system incorporates High-Definition Multimedia Interface (HDMI™) technology. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.

“BRAVIA” logo is a trademark of Sony Corporation.

“ClearAudio+” is a trademark of Sony Corporation.

“PlayStation” is a registered trademark or trademark of Sony Interactive Entertainment Inc.

MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer IIS and Thomson.

word mark and logos are

All other trademarks are trademarks of their respective owners.

Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. This product is protected by certain intellectual property rights of Microsoft Corporation. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft or an authorized Microsoft subsidiary.

警告

切勿將本設備安裝在狹窄的空間內，如書櫃或壁櫥內。

為了降低發生火災的危險，請勿使用報紙、桌布、窗簾等物品蓋住設備的通風孔。請勿將如點燃的蠟燭等明火源放置於設備上。

為了降低發生火災或觸電的危險，請勿讓本設備受到液體潑濺，也不要將如花瓶等裝滿液體的物體放置於本設備上。

只要交流變壓器的電源線仍連接在電源插座上，即使本機的電源已經關閉，但交流變壓器仍然未與交流電源斷開連接。

由於交流電源轉接器的主插頭用於斷開交流電源轉接器和電源的連接，請將其連接至易於插拔的交流電源插座。若發現異常狀況，請立即將其從交流電源插座斷開連接。

請勿讓電池或安裝電池的設備暴露在過熱的環境中，例如：陽光、火等。

限室內使用。

建議的電纜

必須使用妥善包覆及接地的電纜和連接器來連接主機電腦和/或週邊設備。

對於主動式揚聲器

此標示牌位於主動式揚聲器的底部。

交流變壓器

交流變壓器型號和序號的標籤位於交流變壓器的底部。

經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。

低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

委製廠商：SONY CORPORATION 進口商：台灣索尼股份有限公司地址：台北市中山北路二段42號5樓洽詢專線：4499111 （手機撥號請加02）

設備名稱：主動式揚聲器，型號（型式）：HT-S200F

單元

電路板－○○ ○ ○ ○

外殼－○○ ○ ○ ○

揚聲器－○○ ○ ○ ○

配件（遙控器等）－ ○ ○ ○ ○ ○

備考1.“○”係指該項限用物質之百分比含量未超出百分比含量基準值。

備考2.“－”係指該項限用物質為排除項目。

鉛

(Pb)汞(Hg)鎘(Cd)

限用物質及其化學符號

六價鉻

(Cr

多溴聯苯

)

(PBB)

多溴二苯醚

(PBDE)

關於本使用說明書 .............. 3

盒中內容 ...................... 4

系統的功能 .................... 5

部件與控制器的指南 ............ 6

連接電視機

透過 HDMI 連接線連接電視機

以無線方式連接具有 BLUETOOTH 功能

的 Sony 電視機 ............ 12

將主動式揚聲器安裝到牆上 ..... 14

電視機遙控器不能操作時 ....... 16

聆聽聲音

聆聽電視和其他裝置 ........... 17

聆聽 USB 裝置上的音樂 ......... 18

選擇音效

調整聲音 ..................... 20

透過 BLUETOOTH® 功能聆聽音樂 / 聲音

聆聽行動裝置中的音樂 ......... 22

透過操作 BLUETOOTH 裝置開啟

系統 ..................... 24

關閉 BLUETOOTH 功能 ........... 24

使用各種功能

使用 HDMI 控制功能 ............ 25

使用 “BRAVIA” 同步功能 ...... 26

HDMI 連接的注意事項 .......... 26

節省耗電量 ................... 27

故障排除

故障排除 ..................... 28

重設系統 ..................... 31

入門指南（另外



的文件）

其他資訊

規格 ......................... 32

可播放檔案的類型

（USB 輸入） ............... 33

支援的輸入音訊格式

（TV 輸入） ................ 33

關於 BLUETOOTH 通訊 ........... 34

預先注意事項 ................. 35

關於本使用說明書

•本使用說明書中的說明描述遙控器上的控制鍵。

•有些插圖作為概念圖，可能與實際產品有差異。

•每個功能說明的預設設定會以底線標示。

盒中內容

• 主動式揚聲器（1）

• 交流電源線（1） – 台灣機型

– 其他國家 / 地區的機型

• 遙控器（1）

• R03 （AAA 大小）電池（2）

• 光纖數位線（1）

• 交流變壓器（1）

• 壁掛式安裝用緩衝墊（2）

• 壁掛式安裝模板（1）

• 入門指南

• 使用說明書

系統的功能

“ 聆聽電視和其他裝置 ”

（第 17 頁）

Blu-ray Disc™ 播放器、有線電視盒、衛星電視盒等

連接電視機

（請參閱 “ 入門指南 ” （另外的文

件））

“使用HDMI控制功能”（第25 頁） “ 使用 “BRAVIA” 同步功能 ”

（第 26 頁）

“ 聆聽 USB 裝置上的音樂”（第18頁）

“ 聆聽行動裝置中的音樂 ”

（第 22 頁）

“ 以無線方式連接具有 BLUETOOTH 功能的 Sony 電視機 ” （第 12 頁）

部件與控制器的指南

插圖省略細節。

主動式揚聲器

正面

 遙控器感應器

將遙控器指向遙控器感應器以操作系統。

（電源）按鈕

開啟系統或設至待機模式。

 （輸入選擇）按鈕（第 17 頁）  BLUETOOTH 按鈕（第 22 頁）

 +/- （音量）按鈕  指示燈

詳情請參閱 “ 關於主動式揚聲器上的指示燈”（第7頁）。

關於主動式揚聲器上的指示燈

主動式揚聲器上的指示燈亮起和閃爍指示輸入裝置的輸入或狀態。

指示燈狀態

• 亮起：選取 TV 輸入。

• 亮起藍燈：已建立 BLUETOOTH 連線（選取 BLUETOOTH 輸入）。

• 快速閃爍藍燈（約一秒兩次）：配對待機狀態時。

• 緩慢閃爍藍燈（約一秒一次）：正在嘗試 BLUETOOTH 連線。

• 亮起：選取 USB 輸入。

• 閃爍兩次：播放模式改變。

• 先閃爍三次，然後反覆緩慢閃爍：連接不支援的裝置時。

• 反覆閃爍：讀取連接的 USB 裝置的資料時。

• 亮起：系統透過 BLUETOOTH 功能連接至電視機（選取 TV 輸入）。

開啟 / 關閉功能設定或操作遙控器時，指示燈會閃爍。

指示燈狀態

• 閃爍兩次：以下功能之一設為開啟。 – 夜間模式（第 20 頁） – 語音模式（第 20 頁）

• 閃爍一次：聲道設為主要（第 21 頁）、選取聲音模式（第 20 頁），或以下功能之一

設為關閉。

– 夜間模式（第 20 頁） – 語音模式（第 20 頁）

• 閃爍兩次：以下功能之一設為開啟。 – Dolby DRC （第 21 頁） – HDMI 控制（第 25 頁） – BLUETOOTH 待機（第 24 頁） – BLUETOOTH 功能（第 24 頁） – 自動待機（第 27 頁） – IR 中繼器（第 16 頁） – 自動音量（第 21 頁） – 壁掛式安裝模式（第 14 頁）

• 閃爍一次：聲道設為次要（第 21 頁），或以下功能之一設為關閉。 – Dolby DRC （第 21 頁） – HDMI 控制（第 25 頁） – BLUETOOTH 待機（第 24 頁） – BLUETOOTH 功能（第 24 頁） – 自動待機（第 27 頁） – IR 中繼器（第 16 頁） – 自動音量（第 21 頁） – 壁掛式安裝模式（第 14 頁）

• 閃爍兩次：透過 BLUETOOTH 功能連接至電視機的功能設定為開啟（第

12 頁）。

• 閃爍一次：透過 BLUETOOTH 功能連接至電視機的功能設定為關閉（第 12 頁）。

指示燈狀態

• 閃爍一次：聲道設為主要 / 次要（第 21 頁）。

• 快速閃爍（約一秒兩次）：保護功能啟動（第 30 頁）。

• 緩慢閃爍（約一秒一次）：系統透過自動待機功能進入待機模式（第

27 頁）。

調整音量時指示燈閃爍。

指示燈狀態

• 閃爍一次：音量低（1 - 20）。/ 低音等級設定為 -1 （輕柔）（第 21 頁）。

• 閃爍一次：音量中等（21 - 40）。/ 低音等級設定為 0（一般）（第 21 頁）。

• 閃爍一次：音量高（41 - 49）。/ 低音等級設定為 +1 （強烈）（第 21 頁）。

• 反覆閃爍：靜音。

• 閃爍兩次：音量設定為最大 / 最小。

提示

您可以按住 AUTO SOUND 5 秒關閉指示燈。即使透過使用 AUTO SOUND 關閉指示燈，當您操作系統時，操作相應的指示燈仍會亮起或閃爍。

背面

 DC IN 端子  HDMI OUT (TV (ARC)) 插孔

用 HDMI 連接線連接具備 HDMI 輸入插孔的電視機。系統相容於 Audio Return Channel

（ARC）。ARC 是將電視機的聲音從

電視機的 HDMI 插孔傳送到系統等 AV 裝置的功能。

 TV IN (OPTICAL) 插孔  （USB）連接埠（第 18 頁）  IR 中繼器（第 16 頁）

將電視機遙控器的遠端訊號傳送到電視機。

 主動式重低音揚聲器

遙控器

某些按鈕的功能可能因按下按鈕的時間長短而異。下方圖示指示按下按鈕的時間長短。

• ：按下按鈕。

• ：按住按鈕 5 秒。

 INPUT （第 17 頁）

選擇播放來源。按一下 INPUT 時，目前輸入指示燈會閃爍。再按一次 INPUT 可選擇您想要的裝置。每次按下 INPUT 時，輸入會如下循環改變。 TV 輸入  BLUETOOTH 輸入  USB 輸入

 AUTO SOUND

：將音效選擇為 AUTO SOUND。（第

20 頁）

：開啟 / 關閉主動式揚聲器上的

指示燈。（第 7 頁）

 CINEMA

：將音效選擇為 CINEMA。（第 20

頁）

：開啟 / 關閉自動待機功能。

（第 27 頁）

 VOICE

：開啟 / 關閉語音模式。（第 20

頁）

：開啟 / 關閉 HDMI 控制功能。

（第 25 頁）

  （音量）+*/-

調節音量。

 BASS

：調整低音等級。（第 21 頁）

：開啟 / 關閉壁掛式安裝模式。

（第 14 頁）

 PLAY MODE （第 18 頁）

選擇 USB 播放的播放模式。

 / （第 18 頁）

在電視機螢幕上選擇 USB 播放的內容。

/ （上一個 / 下一個）（第

18、22 頁）

短按按鈕可前往上一個或下一個檔案的開頭。按住可向後或向前搜尋（倒轉 / 快轉）。

（電源）

開啟系統或設至待機模式。

 STANDARD

：將音效選擇為 STANDARD。（第 20

頁）

：開啟/關閉IR中繼器功能。

（第 16 頁）

 MUSIC （第 20 頁）

：將音效選擇為 MUSIC。（第 20

頁）

：開啟 / 關閉自動調整音量的功

能。（第 21 頁）

 NIGHT

：開啟 / 關閉夜間模式。（第 20

頁）

：開啟 / 關閉 BLUETOOTH 待機模

式。（第 24 頁）

  （靜音）

暫時關閉聲音，或是開啟聲音。

 AUDIO*

：選擇 Dolby Digital 多路廣播的

聲道。（第 21 頁）

：開啟 / 關閉 Dolby DRC 功能。

（第 21 頁）

 ENTER （第 18 頁）

播放透過 / 選取的內容以進行 USB 播放。

  （播放 / 暫停） * （第 18、

22 頁）

暫停或繼續播放。

關於更換遙控器的電池

系統不回應遙控器操作時，請更換兩顆新電池。使用 R03 （AAA 大小）錳電池進行更換。

* AUDIO、 + 和  按鈕有觸覺點。操作

時，可將其作為參考點。

連接電視機

Blu-ray Disc 播放器、有線電視盒、衛星電視盒等

INPUT

BLUETOOTH 按鈕

透過 HDMI 連接線連接電視機

請參閱入門指南（另外的文件）。

以無線方式連接具有 BLUETOOTH 功能的 Sony 電視機

使用具備 BLUETOOTH 功能的 Sony 電視機 * 時，您可以透過無線的方式連接系統與電視機，以聆聽電視機或電視機所連接裝置的聲音。

* 電視機必須與 A2DP （Advanced Audio

Distribution Profile）相容。

透過無線的方式連接系統與電視機

若要透過無線的方式連接系統與電視機，必須使用 BLUETOOTH 功能執行系統與電視機的配對。配對是預先在要無線連接的 BLUETOOTH 裝置上相互註冊資訊所需的過程。

註

如果透過 BLUETOOTH 功能連接系統與電視機，則無法顯示系統的操作畫面，如 USB 播放畫面，也無法使用除了聆聽電視機或電視機所連接裝置的聲音以外的系統功能。若要使用系統的所有功能，請使用 HDMI 連接線（無附帶）連接系統和電視機。有關透過 HDMI 連接線連接以聆聽電視機聲音的連接和操作詳情，請參閱入門指南（另外的文件）。

1 同時按住主動式揚聲器上的

BLUETOOTH 按鈕和遙控器上的 INPUT 5秒。

TV 和 BLUETOOTH 指示燈閃爍兩次，系統進入配對模式，然後 BLUETOOTH 指示燈快速閃爍。

2 在電視機上，透過執行配對操作搜尋



 +/-



STANDARD AUTO SOUND

MUSIC CINEMA

NIGHT VOICE

BASS

系統。

搜尋到的 BLUETOOTH 裝置清單出現在電視機螢幕上。關於將 BLUETOOTH 裝置與電視機配對的操作方法，請參閱電視機的使用說明書。

3 透過從電視機螢幕上的清單中選擇

“HT-S200F” 來配對系統和電視機。

4 確定主動式揚聲器上的 BLUETOOTH 和

TV 指示燈亮起。

系統與電視機之間的連線已建立，電視機的聲音從系統輸出。配對完成後，當系統開啟時，電視機的聲音會自動從系統輸出。

註

• 如果系統無法輸出電視機的聲音，重複按下 INPUT 選擇 TV 輸入，然後檢查主動式揚聲器上的指示燈狀態。 – BLUETOOTH 和 TV 指示燈亮起：系統和電視

機已連接，電視機的聲音從系統輸出。

– BLUETOOTH 指示燈快速閃爍：正在電視機

上執行配對。

– TV 指示燈亮起：從頭開始重新執行步驟。

• 透過 HDMI 連接線（無附帶）連接系統和電

視機時，BLUETOOTH 連接取消。若要再次透過 BLUETOOTH 功能連接系統和電視機，請斷開 HDMI 連接線，然後從頭開始執行連接操作。

• 若要在配對第一台電視機後配對其他電視機，請關閉已配對的電視機，然後按照行動裝置的連接步驟進行新的配對（第 22 頁）。

聆聽電視機或電視機所連接裝置的聲音

透過無線的方式連接系統與電視機時，您可以使用電視機遙控器開啟 / 關閉系統、調整音量和靜音。

1 使用電視機遙控器開啟電視機。

透過連結電視機電源開啟系統，電視機的聲音從系統輸出。

2 使用電視機遙控器選擇節目或裝置的

輸入。

電視機螢幕上顯示的影像聲音從系統輸出。

3 使用電視機遙控器調整系統音量。

在電視機遙控器上按下靜音按鈕時，會暫時靜音。

提示

電視機關閉時，也會透過連結電視機電源關閉系統。

關於系統附帶的遙控器的操作

您可以使用以下按鈕。除了可以使用電視機遙控器操作系統開啟 / 關閉及調整音量之外，您還可以調整低音等級和音質。

註

如果在系統附帶的遙控器上選擇 USB 輸入，系統無法輸出電視機的聲音。若要輸出電視機的聲音，按遙控器上的 INPUT 選擇TV輸入。

將主動式揚聲器安裝到牆上

您可以將主動式揚聲器安裝到牆上。

註

• 準備適合牆壁材料和強度的螺絲（無附帶）。由於石膏板牆壁易碎，請將螺絲牢固釘入牆柱。水平安裝揚聲器，並將其懸掛在連續平面牆柱上的螺絲上。

• 讓 Sony 經銷商或授權承包商完成安裝，並在安裝期間特別注意安全事宜。

• 對因安裝錯誤、牆壁不夠堅固、螺絲安裝錯誤或自然災害等引起的事故或損壞，Sony 概不負責。

1 準備適合主動式揚聲器背面壁掛孔的

主動式揚聲器背面的孔

4mm

超過 30 mm

5 mm

10 mm

電視機中心

壁掛式安裝模板

膠帶等

螺絲

標示位置（）

5 mm 至 6 mm

200 mm

緩衝墊

兩個螺絲（無附帶）。

2 將壁掛式安裝模板（附帶）貼在牆

上。

1 將壁掛式安裝模板的電視機中心線

（）對齊電視機的中心線。

2 將壁掛式安裝模板的電視機底部線

（）對齊電視機的底部，然後使

用市售膠帶等將壁掛式安裝模板黏貼到牆壁上。

3 如下圖所示，在壁掛式安裝模板的螺

絲線（）上的標示位置（）鎖緊螺絲。

4 取下壁掛式安裝模板。 5 將緩衝墊（附帶）安裝在主動式揚聲

器背面孔下方。

6 將主動式揚聲器掛在螺絲上。

將主動式揚聲器的背面孔對齊螺絲，然後將主動式揚聲器掛在兩個螺絲上。

7 按住 BASS 5 秒可將壁掛式安裝模式設

為開啟。

USB 指示燈閃爍兩次。您可最佳化安裝到牆上的系統聲音。

註

• 黏貼壁掛式安裝模板時，將它完全撫平。

• 若要將壁掛式安裝模式設為關閉，按住BASS

5 秒。USB 指示燈閃爍一次。

電視機遙控器不能操作時

當主動式揚聲器擋到電視機的遙控器感應器時，電視機遙控器可能會無法使用。在此狀況下，請啟用系統上的 IR 中繼器功能。透過從主動式揚聲器背面傳送遠端訊號，可以使用電視機遙控器控制電視機。

按住 STANDARD 5 秒可開啟或關閉功能。

IR 中繼器開啟

USB 指示燈閃爍兩次。

IR 中繼器關閉

USB 指示燈閃爍一次。

註

• 請務必確定電視機遙控器無法控制電視機，再將 IR 中繼器功能設為開啟。如果該設定在遙控器可控制電視機時設為開啟，則因為遙控器的直接命令與透過主動式揚聲器發出的命令之間有干擾，所以可能無法適當操作。

• 在某些電視機上，此功能可能無法正確運作。在此情況下，請將主動式揚聲器稍微遠離電視機。

聆聽聲音

INPUT

 +/-

BASS

聆聽電視和其他裝置

1 重複按下 INPUT。

按一下 INPUT 時，目前輸入指示燈會閃爍。再按一次 INPUT 可選擇您想要的裝置。所選裝置的指示燈亮起。每次按下 INPUT 時，輸入會如下循環改變。 TV 輸入  BLUETOOTH 輸入  USB 輸入

TV 輸入

• 連接至 TV IN (OPTICAL) 插孔的電視機

• 連接至HDMI OUT (TV (ARC))插孔的Audio

Return Channel （ARC）功能相容的電視

機當您將電視機連接至 HDMI OUT (TV (ARC)) 和 TV IN (OPTICAL) 插孔時，會根據先輸入的音訊訊號選擇音訊輸入插孔。

BLUETOOTH 輸入

支援 A2DP 的 BLUETOOTH 裝置詳情請參閱 “ 透過 BLUETOOTH® 功能聆聽音樂 / 聲音 ” （第 22 頁）。

USB 輸入

連接至（USB）連接埠的 USB 裝置詳情請參閱 “ 聆聽 USB 裝置上的音樂 ”

（第 18 頁）。

2 調節音量。

• 按下遙控器上的  +/- 調節音量。

• 按下遙控器上的 BASS 調整低音等級

（第 21 頁）。

提示

您也可以按下主動式揚聲器上的選擇輸入。

聆聽 USB 裝置上的音樂

ENTER

PLAY MODE

 +/-



/

INPUT

/

BASS

您可播放在連接的 USB 裝置上儲存的音樂檔案。有關可播放檔案的類型，請參閱 “ 可播放檔案的類型（USB 輸入）” （第 33 頁）。

註

• 若要在電視機螢幕上檢視 USB 內容清單，確認您使用 HDMI 連接線將系統連接至電視機。

• 將電視機的輸入變更為主動式揚聲器連接的輸入。

1 將 USB 裝置連接至（USB）連接埠。

2 重複按下 INPUT 選擇 “USB”。

USB 指示燈亮起，電視機螢幕上出現 USB 內容清單。

3 按 / 選擇您想要的內容，然後按

ENTER。

開始播放所選擇的內容。

4 重複按下PLAY MODE可選擇您想要的播

放模式。

• 無：播放所有曲目。

• [ ] （重複一首）：重複播放一首

曲目。

[ ] （重複資料夾）：重複播放

•

資料夾內的所有曲目。

[ ] （隨機）：隨機重複播放資料

•

夾內的所有曲目。

• [ ] （全部重複）：重複播放所有曲目。

每次按下 PLAY MODE，USB 指示燈就會閃爍兩次。

5 調節音量。

• 按下遙控器上的  +/- 調節音量。

• 按下遙控器上的 BASS 調整低音等級

（第 21 頁）。

其他操作

若要動作

暫停或繼續播放按 。選擇上一首或下一首曲目按 /。

電視機螢幕上的 USB 裝置資訊

向後或向前搜尋（倒轉/快轉）

註

• 操作時請勿拔下 USB 裝置。為了避免破壞數據或損壞 USB 裝置，請在連接或拔下 USB 裝置前關閉系統。

• 如果您連接不支援的USB 裝置，USB 指示燈會先閃爍三次，然後反覆緩慢閃爍。

按住 /。

 播放時間  總播放時間  位元速率  播放狀態  倒轉/快轉速度  重複播放狀態  所選檔案索引 / 資料夾內的檔案總數

電視機螢幕上出現以下訊息。

• [File Unsupported] 略過不支援的檔案時，在左下方顯示 1秒。

• [Device Not Support] – 不支援 USB 裝置。 – 插入的裝置並非 USB 裝置、USB 裝置受

損或 USB 裝置內沒有檔案。

• [No USB] 未插入 USB 裝置。

• [Waiting] 系統正在搜尋 USB 裝置。

• [This device is empty] USB 裝置內沒有可播放的檔案。

註

• 視播放來源而定，可能無法顯示某些資訊。

• 視播放模式而定，顯示的資訊可能不同。

選擇音效

STANDARD

AUTO SOUND MUSIC

CINEMA

調整聲音

深夜時以低音量欣賞清晰的聲音（NIGHT）

在失真度最低且對話清晰的狀況下以低音量輸出聲音。

欣賞針對音源的音效（聲音模式）

您可輕鬆欣賞針對不同的音源而預先編程的音效。

按 AUTO SOUND、CINEMA、MUSIC 或 STANDARD 選擇聲音模式。

選擇聲音模式時，TV 指示燈閃爍一次。

AUTO SOUND

您可以使用 Sony 建議的聲音模式欣賞聲音。聲音模式根據播放內容和功能自動最佳化。

CINEMA

以環繞效果播放聲音，真實呈現強而有力的聲音，適合觀賞影片。

MUSIC

針對聆聽音樂最佳化的音效。

STANDARD

針對個別來源最佳化的音效。

按 NIGHT 可開啟或關閉功能。

夜間模式開啟

TV 指示燈閃爍兩次。

夜間模式關閉

TV 指示燈閃爍一次。

註

關閉系統時，夜間模式會自動設為關閉。

讓對話更清楚（VOICE）

您可以透過將語音模式設為開啟使對話更清楚。

按 VOICE 可開啟或關閉功能。

語音模式開啟

TV 指示燈閃爍兩次。

語音模式關閉

TV 指示燈閃爍一次。

透過壓縮動態範圍輕鬆聽到低音量的聲音

此功能僅在播放連接至 TV IN (OPTICAL)/ HDMI OUT (TV (ARC)) 插孔的裝置的 Dolby Digital 訊號時有效。將 Dolby DRC （動態範圍控制）設為開啟時，音訊訊號的動態範圍（最大和最小音量之間的範圍）會被壓縮，因此可輕鬆聽到低音量的聲音。

按住 AUDIO 5 秒可開啟或關閉功能。

Dolby DRC 開啟

USB 指示燈閃爍兩次。

Dolby DRC 關閉

USB 指示燈閃爍一次。

欣賞多路廣播聲音（AUDIO）

當系統接收 Dolby Digital 多路廣播訊號時，可以欣賞多路廣播聲音。

重複按下 AUDIO。

聲道會如下循環改變。

 次要  主要/次要

主要

僅輸出主要聲道。 TV 指示燈閃爍一次。

次要

僅輸出次要聲道。 USB 指示燈閃爍一次。

主要 / 次要

主音從左揚聲器中輸出，副音從右揚聲器中輸出。 TV 和 USB 指示燈閃爍一次。

註

若要接收 Dolby Digital 訊號，您需使用光纖數位線（附帶）將電視機或其他裝置連接至 TV IN (OPTICAL) 插孔或使用 HDMI 連接線

（無附帶）連接至 HDMI OUT (TV (ARC)) 插

孔。

自動調整已連接裝置的音量

您可以透過將自動音量功能設為開啟，根據已連接裝置的輸入訊號或內容自動調整音量。

按住 MUSIC 5 秒可開啟或關閉功能。

自動音量功能開啟

USB 指示燈閃爍兩次。

自動音量功能關閉

USB 指示燈閃爍一次。

調整低音等級

重複按下 BASS。

低音等級會如下循環改變。

 +1  0  -1  0...

0 （一般）

TV 和 BLUETOOTH 指示燈閃爍一次。

+1 （強烈）

所有指示燈閃爍一次。

-1 （輕柔）

TV 指示燈閃爍一次。

註

當輸入來源未含有太多低音時，例如電視節目，可能會難以聽見主動式重低音揚聲器的低音。

透過 BLUETOOTH® 功能聆聽音

BLUETOOTH 指示燈

BLUETOOTH 按鈕

樂/聲音

聆聽行動裝置中的音樂

使用 BLUETOOTH 功能連接系統與行動裝置，可以透過無線連接聆聽儲存在智慧型手機或平板電腦等行動裝置上的音樂。透過 BLUETOOTH 功能連接行動裝置時，只要使用附帶的遙控器就能操作，不需開啟電視。

透過與行動裝置配對聆聽音樂

1 按住主動式揚聲器上的 BLUETOOTH 按

鈕5秒。

系統進入配對模式，且 BLUETOOTH 指示燈快速閃爍。

系統進入配對模式後，如果 5 分鐘內未執行配對，配對模式會取消。在此情況下，請從頭開始執行配對。

2 在行動裝置上，透過執行配對操作搜

尋系統。

搜尋到的 BLUETOOTH 裝置清單出現在行動裝置的螢幕上。關於將 BLUETOOTH 裝置與行動裝置配對的操作方法，請參閱行動裝置的使用說明書。

3 透過從行動裝置螢幕上的清單中選擇

“HT-S200F” 來配對系統和行動裝置。

如需密碼，請輸入 “0000”。

4 確定主動式揚聲器上的 BLUETOOTH 指

示燈亮起藍燈。

系統與行動裝置之間的連線已建立。

5 使用所連線行動裝置上的音樂應用程

式開始播放音訊。

聲音從主動式揚聲器輸出。

6 調節音量。

• 按下遙控器上的  +/- 調節音量。

• 按下遙控器上的 BASS 調整低音等級

（第 21 頁）。

• 遙控器上的  和 / 可用

於 BLUETOOTH 功能。（倒轉和快轉也可使用。）

註

• 您最多可以配對 10 個 BLUETOOTH 裝置。如果

配對第 11 個 BLUETOOTH 裝置，新的裝置將替換最早連接的裝置。如果已配對具有 BLUETOOTH 功能的 Sony 電視機，將其視為 BLUETOOTH 裝置。

• 為第二個和之後的行動裝置執行配對。

提示

• 您可檢查 BLUETOOTH 指示燈狀態以確定

BLUETOOTH 功能的連線狀態（第 7 頁）。

• 選取 BLUETOOTH 輸入時，短按主動式揚聲器

上的 BLUETOOTH 按鈕可使系統進入配對模式。

• 未選取 BLUETOOTH 輸入時，短按主動式揚聲

器上的 BLUETOOTH 按鈕可使系統自動重新連接最近連線的 BLUETOOTH 裝置。

聆聽已配對行動裝置中的音樂

INPUT

 +/-

BASS



/

1 開啟行動裝置的 BLUETOOTH 功能。 2 重複按下 INPUT 選擇 BLUETOOTH輸入或

短按主動式揚聲器上的 BLUETOOTH 按鈕。

BLUETOOTH 指示燈閃爍，系統會自動重新連接最近連線的 BLUETOOTH 裝置。

3 確定 BLUETOOTH 指示燈亮起藍燈。

系統與行動裝置之間的連線已建立。

4 使用所連線行動裝置上的音樂應用程

式開始播放音訊。

聲音從主動式揚聲器輸出。

5 調節音量。

• 按下遙控器上的  +/- 調節音量。

• 按下遙控器上的 BASS 調整低音等級

（第 21 頁）。

• 遙控器上的  和 / 可用

於 BLUETOOTH 功能。（倒轉和快轉也可使用。）

透過操作 BLUETOOTH 裝置開啟系統

若系統具有配對資訊，透過將 BLUETOOTH 待機模式設為開啟，即使系統處於待機模式，您仍可從 BLUETOOTH 裝置開啟系統並聆聽音樂。

按住 NIGHT 5 秒可開啟或關閉功能。

BLUETOOTH 待機模式開啟

USB 指示燈閃爍兩次。

BLUETOOTH 待機模式關閉

USB 指示燈閃爍一次。

註

BLUETOOTH 待機模式開啟時，待機耗電量增加。

關閉 BLUETOOTH 功能

您可以關閉 BLUETOOTH 功能。

按住主動式揚聲器上的 、和 - 10 秒開啟或關閉功能。

BLUETOOTH 功能開啟

USB 指示燈閃爍兩次。

BLUETOOTH 功能關閉

USB 指示燈閃爍一次。

註

若 BLUETOOTH 功能設為關閉，透過按 INPUT 選擇輸入時，會略過 BLUETOOTH 輸入。

使用各種功能

使用 HDMI 控制功能

透過 HDMI 連接線（無附帶）連接與 HDMI 控制功能 * 相容的電視機或 Blu-ray Disc 播放器等裝置，可讓您使用電視機或 Bluray Disc 播放器的遙控器輕鬆操作裝置。以下功能可以與 HDMI 控制功能一起使用。

• 系統關閉功能

• 系統聲音控制功能

• Audio Return Channel

• 觸控播放功能

註

這些功能可能適用於非 Sony 製造的裝置，但不保證能正常運作。

* HDMI 控制是 CEC （Consumer Electronics

Control）用於讓 HDMI （高解析度多媒體介面）裝置互相控制的標準。

準備使用 HDMI 控制功能

按住 VOICE 5 秒可開啟或關閉功能。

HDMI 控制功能開啟

USB 指示燈閃爍兩次。

HDMI 控制功能關閉

USB 指示燈閃爍一次。

為電視機和連接至電視機的其他裝置啟用 HDMI 控制功能設定。

提示

如果您在使用 Sony 製造的電視機時啟用 HDMI 控制（“BRAVIA” 同步）功能，系統的 HDMI 控制功能也會自動啟用。

系統關閉功能

關閉電視機時，也會自動關閉系統。

系統聲音控制功能

若您在觀賞電視時開啟系統，則電視機的聲音會從系統的揚聲器輸出。可以使用電視機遙控器調整系統音量。若您在上次觀賞電視時，電視機的聲音是從系統的揚聲器輸出，則重新開啟電視機時，系統也會自動開啟。也可以使用電視機選單進行操作。詳情請參閱電視機的使用說明書。

註

• 視電視機而定，表示系統音量的數字會顯示

在電視機螢幕上。

• 視電視機的設定而定，系統聲音控制功能可

能無效。詳情請參閱電視機的使用說明書。

Audio Return Channel

如果系統連接至與 Audio Return Channel

（ARC）相容的電視機 HDMI IN 插孔，您可

以從系統的揚聲器聆聽電視機的聲音，而不需連接光纖數位線。

註

如果電視機與 Audio Return Channel 不相容，需要連接光纖數位線（附帶）（請參閱附帶的入門指南）。

觸控播放功能

當您在與電視機連接的裝置（Blu-ray Disc 播放器、“PlayStation 播放內容時，本系統與電視機會自動開啟，系統的輸入會切換到 “TV” 輸入，聲音會從系統的揚聲器輸出。

註

• 如果您上次觀賞電視時電視機的聲音從電視

機的揚聲器輸出，則即使播放裝置內容，系統也不會開啟，而且聲音和圖像會從電視機輸出。

• 視電視機而定，可能無法正確播放所播放內

容的起始處。

4” 等）上

使用 “BRAVIA” 同步功能

除了 HDMI 控制功能以外，您也可以在與 “BRAVIA” 同步功能相容的裝置上使用以下功能。

• Sound mode/ 場景選擇功能

• 家庭劇院控制

註

這些功能是 Sony 的專利功能。此功能無法在非 Sony 製造的產品上運作。

Sound mode/ 場景選擇功能

系統的聲音模式會根據電視機的場景選擇功能或聲音模式的設定自動切換。詳情請參閱電視機的使用說明書。將聲音模式設為 “AUTO SOUND” （第 20 頁）。

家庭劇院控制功能

使用與家庭劇院控制功能相容的電視機時，不需切換 TV 輸入就能設定系統、設定聲音模式設定、切換輸入等。當電視機連接到網際網路時，可以使用此功能。詳情請參閱電視機的使用說明書。

HDMI 連接的注意事項

• 使用 HDMI 授權的連接線。

• 建議使用有連接線類型標誌的 Sony 支援

乙太網路連接的高速 HDMI 傳輸線。

• 我們不建議使用 HDMI-DVI 轉換線。

• 連接裝置可能會抑制經由 HDMI 插孔傳輸

的音訊訊號（取樣頻率、位元長度等）。

節省耗電量

若要在節省耗電量的情況下使用系統，請變更以下設定。

透過偵測使用狀態關閉系統

若將自動待機功能設為開啟，當您大約 20 分鐘沒有操作系統，而且系統沒有接收到輸入訊號時，系統會自動進入待機模式。

按住 CINEMA 5 秒可開啟或關閉功能。

自動待機開啟

USB 指示燈閃爍兩次。

自動待機關閉

USB 指示燈閃爍一次。

待機模式中省電

若要在待機模式中節省耗電量，將 BLUETOOTH 待機模式（第 24 頁）和 HDMI 控制功能（第 25 頁）設為關閉。預設設定為開啟。

故障排除

若您在使用系統時遇到任何以下問題 , 請在尋求維修之前使用此故障檢修指南以幫助您解決有關問題。若問題持續，請就近與 Sony 經銷商聯絡。

圖像

沒有圖像或圖像輸出不正確。

 選擇適當的輸入（第 17 頁）。  選擇 TV 輸入時，如果沒有圖像，請使用

電視機遙控器選擇您要的電視頻道。

 斷開 HDMI 連接線，然後再次連接。確定

連接線已插牢。

聲音

電源

系統電源未開啟。

 檢查交流電源線和交流變壓器已穩固地

連接。

 將交流電源線從牆壁插座中拔出，數分

鐘後再重新接上。

系統自動關閉。

 自動待機功能運作。將自動待機功能設

為關閉（第27頁）。

雖然電視機開啟，但系統沒有開啟。

 將 HDMI 控制功能設為開啟（第 25 頁）。

電視機必須支援 HDMI 控制功能。詳情請參閱電視機的使用說明書。

 檢查電視機的揚聲器設定。系統電源與

電視機的揚聲器設定同步。詳情請參閱電視機的使用說明書。

 如果上次聲音從電視機的揚聲器輸出，

即使電視機開啟，系統也不會開啟。

當電視機關閉時，系統也關閉。

 檢查 HDMI 控制功能的設定（第 25 頁）。

當 HDMI 控制功能設為開啟且系統的輸入為 TV 輸入，關閉電視機時，系統會自動關閉。

雖然電視機關閉，但系統沒有關閉。

 檢查 HDMI 控制功能的設定（第 25 頁）。

當關閉電視機，只有在系統的輸入為 TV 輸入時，系統才會自動關閉。電視機必須支援 HDMI 控制功能。詳情請參閱電視機的使用說明書。

系統無法輸出電視機的聲音。

 檢查連接系統與電視機的 HDMI連接線或

光纖數位線的類型和連接（請參閱附帶的入門指南）。

 斷開連接在電視機和系統之間的連接

線，然後重新牢固地連接。從交流電源插座斷開電視機和系統的交流電源線，然後重新連接。

 透過 HDMI 連接線連接本系統和電視機

時，檢查以下內容。 – 所連接電視機的 HDMI 插孔標示

“ARC”。

– 電視機的 HDMI 控制功能設為開啟。 – 在系統上，HDMI 控制功能設為開啟

（第 25 頁）。

 如果電視機與 Audio Return Channel 不

相容，請連接光纖數位線（附帶）（請參閱附帶的入門指南）。如果電視機與 Audio Return Channel 不相容，即使系統連接至電視機的 HDMI IN 插孔，電視機的聲音也不會從系統輸出。

 如果連接電視機光纖輸入插孔的裝置沒

有輸出聲音，請嘗試以下操作。 – 將有線電視盒或衛星電視盒直接連接

到系統的 TV IN (OPTICAL) 插孔。

 重複按下 INPUT 選擇 TV 輸入（第 17

頁）。

 提高電視機音量或取消靜音。  視您連接電視機與系統的順序而定，系

統可能會靜音。如果發生此狀況，請先打開電視機，再啟動系統。

 將電視機（BRAVIA）的揚聲器設定設

為音訊系統。請參閱電視機的使用說明書中有關如何設定電視機的資訊。

 檢查電視機的聲音輸出。請參閱電視機

的使用說明書中有關電視機設定的資訊。

 系統支援Dolby Digital和PCM音訊格式

（第 33 頁）。播放不支援的格式時，將

電視機（BRAVIA）的數位音訊輸出設定設為 “PCM”。詳情請參閱電視機的使用說明書。

系統與電視機同時輸出聲音。

 將系統或電視機的聲音靜音。

連接至系統的裝置未從系統發出聲音，或聲音很小。

 按  +，並檢查音量（第 10 頁）。

 或  + 以取消靜音功能（第 10

 按

頁）。

 確認已正確選擇輸入來源。您應該重複

按 INPUT 來嘗試其他輸入來源（第 17 頁）。

 檢查系統與連接裝置的所有連接線與導

線是否皆已插牢。

 如果連接的裝置支援向上採樣功能，必

須將其關閉。

不能產生環繞效果。

 視輸入訊號與聲音模式設定而定，環繞

聲處理可能無法有效運作。環繞音效可能不明顯，視節目或光碟而定。

 若要播放多聲道音訊，請檢查連接本系

統的裝置上，數位音訊輸出設定是否正確。詳情請參閱連接裝置附帶的使用說明書。

主動式重低音揚聲器

主動式重低音揚聲器沒有聲音或只聽到極細微的聲音。

 重複按下 BASS 調整低音等級（第 21

頁）。

 若輸入來源包含的低音聲音元件很少

（也就是電視機廣播），則可能會難以

聽見主動式重低音揚聲器的聲音。按照

以下步驟播放內建示範音樂，並確定聲音從主動式重低音揚聲器輸出。  按住主動式揚聲器上的 5 秒。

播放內建示範音樂。

 再按一次。

內建示範音樂取消，系統返回原先狀態。

 將夜間模式設為關閉。詳情請參閱 “ 深

夜時以低音量欣賞清晰的聲音

（NIGHT）” （第 20 頁）。

 主動式重低音揚聲器位於主動式揚聲器

底部。確定主動式重低音揚聲器不會撞到障礙物。

USB 裝置連接

USB 裝置不被識別。

 嘗試以下操作 :

 關閉系統。  移除 USB 裝置，然後再次連接。  開啟系統。

 確保 USB 裝置穩固地連接至（USB）連

接埠（第 18 頁）。

 檢查 USB 裝置或連接線是否損壞。  確保 USB 裝置已開啟。  如果透過 USB 集線器連接 USB裝置，切斷

連接，然後將 USB 裝置直接連接至系統。

行動裝置連接

無法完成 BLUETOOTH 連線。

 確認主動式揚聲器上的 BLUETOOTH 指示

燈亮起（第6頁）。

 確認要連接的 BLUETOOTH 裝置已開啟，

並已啟用 BLUETOOTH 功能。

 讓 BLUETOOTH 裝置靠近系統。  再次配對本系統和 BLUETOOTH 裝置。您

可能需要先使用 BLUETOOTH 裝置取消本系統的配對。

 如果 BLUETOOTH 功能設為關閉，將其設

為開啟（第24頁）。

無法完成配對。

 讓 BLUETOOTH 裝置靠近系統。

 確認本系統未接收來自無線 LAN 裝置、

其他 2.4 GHz 無線裝置或微波爐的干擾。如果附近有產生電磁幅射的裝置，請將該裝置移離本系統。

 如果系統附近有其他 BLUETOOTH 裝置，

可能無法配對。在此情況下，請關閉其他 BLUETOOTH 裝置。

系統無法輸出所連接 BLUETOOTH 行動裝置的聲音。

 確認主動式揚聲器上的 BLUETOOTH 指示

燈亮起（第6頁）。

 讓 BLUETOOTH 裝置靠近系統。  如果附近有產生電磁輻射的裝置，如無

線 LAN 裝置、其他 BLUETOOTH 裝置或微波爐，請將該裝置移離本系統。

 將USB 3.0裝置與其連接線移離本系統。  請將本系統與 BLUETOOTH 裝置之間的任

何障礙物移開，或將本系統遠離障礙物。

 如果系統安裝於電視機下方，請將系統

移離電視機。

 重新擺放連接的 BLUETOOTH 裝置。  將任何附近的無線 LAN 路由器或 PC 的無

線 LAN 頻率切換到 5 GHz 的範圍。

 調高連接的 BLUETOOTH 裝置的音量。

聲音與影像不同步。

 觀賞影片時，您聽到的聲音可能會比影

像慢一些。

遙控器

本系統的遙控器不能操作。

 將遙控器指向主動式揚聲器上的遙控器

感應器（第6頁）。

 移除遙控器和系統之間的所有障礙物。  若遙控器的電池電量不足，請更換兩顆

新電池。

 確認您在遙控器上按下正確按鈕（第

10 頁）。

電視機遙控器不能操作。

 安裝主動式揚聲器時，不要擋到電視機

的遙控器感應器。

 啟用 IR 中繼器功能可能可解決此問題

（第 16 頁）。

其它

HDMI 控制功能不能正常操作。

 檢查系統連線（請參閱附帶的入門指

南）。

 啟用電視機的 HDMI 控制功能。詳情請參

閱電視機的使用說明書。

 請稍等片刻，然後再試一次。如果拔出

系統的插頭，要稍等一下才能進行操作。等待 15 秒以上，然後再試一次。

 確保連接系統的裝置支援 HDMI 控制功

能。

 啟用連接系統的裝置的 HDMI 控制功能。

詳情請參閱您裝置的使用說明書。

 HDMI 控制功能可控制的裝置類型與數目

受 HDMI CEC 標準的限制，如下所示： – 錄製裝置（Blu-ray Disc 錄影機、

DVD 錄影機等）：最多 3 個裝置

– 播放裝置（Blu-ray Disc 播放器、

DVD 播放器等）：最多 3 個裝置

– 與調諧器相關的裝置：最多 4 個裝置 – 音訊系統（接收器 / 耳機）：最多1個

裝置（本系統使用）

主動式揚聲器上的所有指示燈閃爍 10 秒，然後系統關閉。

 保護功能啟動。拔出交流電源線，並檢

查下列項目。 – 確保主動式揚聲器的通風未被擋住，

在一段時間後開啟系統。

– 當系統使用 USB 連接時，請移除 USB 裝

置，然後開啟系統。如果系統正常運作，可能是連接的 USB 裝置電流超過系統最大輸出電流 500 mA，或 USB 裝置可能異常。

電視機感應器未正確運作。

 主動式揚聲器可能會阻礙某些感應器

（例如亮度感應器）、電視機的遙控器

接收器、支援紅外線 3D 眼鏡系統之 3D 電視機的 3D 眼鏡發射器（紅外線傳輸）或無線通訊。在允許部件正確運作的範圍內，將主動式揚聲器從電視機處移開。有關感應器和遙控器接收器的位置，請參閱電視機附帶的使用說明書。

系統沒有正常運作。

 系統可能處於示範模式。若要取消示範

模式，請重設系統。按住主動式揚聲器上的 - （音量）和  （電源）超過 5 秒

（第 31 頁）。

當您按下 INPUT 從 USB 輸入變更為 TV 輸入時，出現訊息。

* 此畫面為英文的範例。

 使用電視機遙控器選擇電視節目。

重設系統

若系統仍無法正確運作，請依以下方法重設系統。

1 按住主動式揚聲器上的 - （音量）和

 （電源）超過 5 秒。

主動式揚聲器上的所有指示燈閃爍 3 次，設定回到初始狀態。

2 拔出交流電源線。 3 連接交流電源線，然後按  開啟系

統。

提示

每個功能說明的預設設定會以底線標示。

其他資訊

規格

放大器部分

功率輸出（額定）

左前 + 右前：20 W + 20 W （4 歐姆， 1 kHz，1% THD）

功率輸出（參考）

左前置 / 右前置揚聲器：25 W （每聲道 4 歐姆，1 kHz) 主動式重低音揚聲器：30 W （4 歐姆， 100 Hz）

輸入

TV IN (OPTICAL) USB

輸出

HDMI OUT (TV (ARC))

USB 部分

（USB）連接埠：

類型 A （用於連接 USB 記憶體）

BLUETOOTH 部分

通訊系統

BLUETOOTH 規格 4.2 版

輸出

BLUETOOTH 規格電源等級 1

最遠通訊範圍

視線範圍約 25 m

頻率波段

2.4 Ghz 波段（2.4000 GHz -

2.4835 GHz）

調製方式

FHSS (Freq Hopping Spread Spectrum)

相容的 BLUETOOTH 模式

A2DP （Advanced Audio Distribution Profile） AVRCP （Audio Video Remote Control Profile）

支援的轉碼器

SBC

傳輸範圍（A2DP）

20 Hz - 20000 Hz （取樣頻率 32 kHz、

44.1 kHz、48 kHz）

實際範圍視裝置之間的障礙物、微波爐附近的磁場、靜電、無線電話、接收靈敏度、作業系統、軟體應用程式等因素而異。

BLUETOOTH 標準模式指出裝置之間的 BLUETOOTH 通訊目的。

轉碼器：音訊訊號壓縮和轉換格式

次頻帶轉碼器的縮寫

揚聲器部分

揚聲器系統

雙向三驅動揚聲器系統、低音反射

揚聲器

左前置 / 右前置揚聲器：46 mm 圓錐型主動式重低音揚聲器：70 mm 圓錐型

一般常規

電源需求

DC 19.5 V （使用連接至 AC 100 V 240 V，50 Hz/60Hz 電源的附帶交流變壓器）

耗電量

開啟：25 W 待機模式：0.5 W 或以下（省電模式）

（HDMI 控制功能和 BLUETOOTH 待機模式

設為關閉時）待機模式：2 W 或以下 *

（HDMI 控制功能和 BLUETOOTH 待機模式

設為開啟時）

* 當沒有 HDMI 連接，而且沒有 BLUETOOTH

配對記錄時，系統會自動進入省電模式。

尺寸 * （約）（寬/高/深）

580 mm × 64 mm × 95 mm

* 不包括突出部分

質量（約）

2.3 kg

設計及規格如有變更，恕不另行通知。

可播放檔案的類型

（USB 輸入）

支援的輸入音訊格式

（TV 輸入）

轉碼器副檔名

MP3 (MPEG-1 Audio Layer III)

WMA9 標準 .wma

LPCM .wav

註

• 某些檔案視檔案格式、檔案編碼或錄製狀態而可能無法播放。

• 可能無法播放一些在 PC 編輯過的檔案。

• 本系統無法播放 DRM 和無損等編碼檔案。

• 本系統可識別在 USB 裝置中的以下檔案或資

料夾： – FAT16/32 的資料夾路徑最長為 128 個字

元，NTFS 最長為 124 個字元

– 多達 200 個資料夾（包括空資料夾和根資

料夾）

– 每個資料夾內多達200個音訊檔案/ 資料夾

• 某些 USB 裝置無法與本系統配合使用。

• 本系統可識別大容量存儲器級別（MSC）裝

置。

.mp3

本系統支援的音訊格式如下。

• Dolby Digital

• 線性 PCM 2ch

關於 BLUETOOTH 通訊

• BLUETOOTH裝置必須在距離彼此約10公尺（無障礙）範圍內才能使用。在下列情

形，實際的通訊範圍可能縮短。 – 當透過 BLUETOOTH 連接的裝置之間有

人、金屬物體、牆壁或其它障礙

– 無線 LAN 安裝的位置 – 在使用中的微波爐周圍 – 其它電磁波發生的地方

• BLUETOOTH 裝置與無線 LAN （IEEE

802.11b/g/n）使用相同的頻率波段

（2.4 GHz）。在有無線 LAN 功能的裝置

附近使用 BLUETOOTH 裝置時，可能會產生電磁干擾。這可能導致較低的數據傳輸率、噪音或無法連接。如果發生這種情況，請嘗試以下補救措施： – 在距離無線 LAN 裝置至少 10 公尺遠的位

置使用本系統。

– 在 10 公尺範圍內使用 BLUETOOTH 裝置

時，請關閉無線 LAN 裝置的電源。

– 安裝本系統與 BLUETOOTH 裝置時儘可能

彼此靠近。

• 本系統的無線電波廣播可能干擾一些醫

療裝置的操作。因為此干擾可能導致故障，在以下地點請總是關閉本系統和 BLUETOOTH 裝置的電源： – 在醫院、火車上、飛機上、加油站以

及任何可能存在可燃氣體的地方

– 靠近自動門或火災報警器

• 本系統支援符合BLUETOOTH規格的安全功

能以確保使用 BLUETOOTH 技術通訊時的安全連接。然而，此安全視設定內容和其它因素而可能不足，因此使用 BLUETOOTH 技術進行通訊時總是要小心。

• Sony對於在使用BLUETOOTH技術通訊過程

中蒙受的損害或資訊洩露造成的其它損失概不負責。

• 無法保證所有與本系統相同模式的

BLUETOOTH 裝置之間的 BLUETOOTH 通訊。

• 與本系統連接的BLUETOOTH裝置必須符合

Bluetooth SIG, Inc. 規定的 BLUETOOTH 規格，而且必須經過認證符合規格。然而，即使裝置符合 BLUETOOTH 規格，還是有 BLUETOOTH 裝置基於特性或規格使裝置無法連接，或導致不同的控制方式、顯示或操作。

• 視連接至本系統的 BLUETOOTH 裝置、通訊環境或周圍情形，可能產生噪音或音訊可能被切斷。

如果您對本系統有任何疑問或問題，請就近與 Sony 經銷商聯絡。

預先注意事項

關於安全

• 如果有任何固體或液體掉入系統，請拔出系統的插頭，並在繼續操作前讓合格的技術人員進行檢查。

• 請勿攀爬主動式揚聲器，否則可能跌落受傷，或是損壞系統。

關於電源

• 操作系統之前，請先確定操作電壓與當地電源供應相符。操作電壓如主動式揚聲器底部的標示牌所示。

• 若您將長時間不使用系統，請務必將系統插頭從牆壁插座拔出。若要切斷交流電源線，請握住插頭拔出，切勿拉扯電線。

• 為了安全起見，插頭的一個葉片寬過另一個，並只能以一個方向插入牆壁插座。如果您不能把插頭完全插入插座，請聯絡您的經銷商。

• 交流電源線必須在合格服務商店更換。

關於變熱

本系統會在操作時變熱，這不是故障。如果持續長時間以高音量使用本系統，系統的背部和底部的溫度會變得相當高。為了避免燙傷，請勿觸碰系統。

關於放置

• 請將系統擺放在通風良好的位置以防止熱量累積，並延長系統的壽命。

• 請勿將系統擺放於靠近熱源的地方，或者會受到陽光直曬、灰塵過多或機械性撞擊的地方。

• 請勿在主動式揚聲器上放置任何物品。

• 若本系統與電視機、錄影機或磁帶卡座搭配

使用，可能會產生雜訊，影響圖像品質。發生此狀況時，請將系統設置在距離電視機、錄影機或磁帶卡座較遠處。

• 將本系統置於經特別處理（打蠟、塗油、拋光等）的表面上時，請務必小心，否則可能會造成表面著色或變色。

• 請小心不要撞到主動式揚聲器的邊角，以免受傷。

• 安裝主動式揚聲器時，請小心不要損壞主動式揚聲器底部的主動式重低音揚聲器。

關於操作

連接其他設備前，請務必關閉系統並拔掉電源插頭。

如果附近的電視機螢幕上出現色彩不均勻

某些類型的電視機可能會出現色彩不均勻的情況。

• 如果出現色彩不均勻 ... 請關閉電視機，在 15 至 30 分鐘後再次開啟。

• 如果再次出現色彩不均勻 ... 將系統設置在距離電視機較遠處。

關於清理

使用柔軟的乾布清潔系統。請勿使用任何類型的砂紙、拋光粉或溶液，如酒精或汽油。

如果您對本系統有任何疑問或問題，請就近與 Sony 經銷商聯絡。

版權與商標

本系統具有 Dolby* Digital。 * Dolby Laboratories 授權製造。

Dolby、Dolby Audio 和雙 D 標誌是 Dolby Laboratories 的商標。

BLUETOOTH Bluetooth SIG, Inc. 所有，Sony Corporation 對該商標的各項使用均已經授權。其他商標和商號是相關擁有者之專利。

本系統包含 High-Definition Multimedia Interface （HDMI™）技術。 HDMI、HDMI 高畫質多媒體介面及 HDMI 標誌為 HDMI Licensing Administrator, Inc. 在美國及其他國家的商標或註冊商標。

“BRAVIA” 標誌為 Sony Corporation 的商標。

“ClearAudio+” 是 Sony Corporation 的商標。

“PlayStation” 是 Sony Interactive Entertainment Inc. 的註冊商標或商標。

MPEG Layer-3 音頻編碼技術和專利由 Fraunhofer IIS 和 Thomson 授權。

Windows Media 是 Microsoft Corporation 在美國和 / 或其它國家的註冊商標或商標。本產品由 Microsoft Corporation 的某些知識產權所保護。在沒有獲得 Microsoft 或授權 Microsoft 子公司許可的情況下，不允許於本產品之外使用或配銷此技術。

字型商標和圖形商標均為

所有其他商標為各自所有者的商標。

http://www.sony.net/

Sony HT-S200F Users guide [zh, en]

Specifications and Main Features

Frequently Asked Questions

User Manual