Sony HCD-GRX80, HCD-RXD8, HCD-RXD8S Service manual

Download

Page 1

HCD-GRX80/RXD8/RXD8S

SERVICE MANUAL

Ver 1.1 2001. 06

HCD-GRX80/RXD8/RXD8S is the tuner, deck, CD and amplifier section in MHC-GRX80/RXD8/RXD8S.

Photo: HCD-RXD8 (SILVER)

Model Name Using Similar Mechanism HCD-GRX8/R800/RX88/RX99

SECTION

TAPE DECK

SECTION

CD Mechanism Type CDM38LH-5BD32L Base Unit Type BU-5BD32L Optical Pick-up Type KSS-213D/Q-N Model Name Using Similar Mechanism HCD-GRX8/R800/RX88/RX99 T ape Transport Mechanism T ype TCM-230AWR1/230PWR1

AEP Model

HCD-RXD8/RXD8S

UK Model

HCD-RXD8

E Model

Australian Model

HCD-GRX80

SPECIFICATIONS

— Continued on next page —

9-928-823-12

COMPACT DISC DECK RECEIVER

Sony Corporation

Home Audio Company

Shinagawa Tec Service Manual Production Group

– 1 –

Page 2

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

Notes on chip component replacement

• Never reuse a disconnected chip component.

• Notice that the minus side of a tantalum capacitor may be damaged by heat.

Flexible Circuit Board Repairing

• Keep the temperature of soldering iron around 270˚C during repairing.

• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering or unsoldering.

Laser component in this product is capable of emitting radiation exceeding the limit for Class 1.

This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior.

This caution label is located inside the unit.

SAFETY-RELATED COMPONENT WARNING !!

COMPONENTS IDENTIFIED BY MARK ! OR DO TTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

– 2 –

Page 3

MODEL IDENTIFICATION — BACK PANEL —

Parts No.

NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT

The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care.

NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.

PARTS No. MODEL

PRODUCT COUNTRY

4-214-451-0π GRX80: E2, AR MALAYSIA 4-214-451-1π GRX80: EA3 MALAYSIA 4-214-451-2π GRX80: SP MALAYSIA 4-214-451-3π GRX80: MX INDONESIA 4-214-451-4π GRX80: MX MALAYSIA 4-214-451-5π GRX80: AUS MALA YSIA 4-214-451-6π GRX80: TW MALAYSIA 4-214-451-7π GRX80: E2 INDONESIA 4-214-451-8π GRX80: EA4, TH THAILAND 4-214-451-9π GRX80: E3 MALAYSIA 4-217-515-2π GRX80: E3 INDONESIA 4-217-515-3π GRX80: EA3 INDONESIA 4-215-165-0π GRX8: AEP, G, CIS, UK INDONESIA 4-215-165-2π GRX8S: AEP INDONESIA 4-215-165-3π GRX8: AEP MALA YSIA

• Abbreviation G : German model MX : Mexican model SP : Singapore model TW : Taiwan model AUS : Australian model TH : Thai model EA3 : Saudi arabia model EA4 : Israel model E2 : Without SW tuner E model E3 : With SW tuner E model

LASER DIODE AND FOCUS SEARCH OPERATION CHECK

Carry out the “S curve check” in “CD section adjustment” and check that the S curve waveform is output four times.

– 3 –

Page 4

TABLE OF CONTENTS

1. SERVICING NOTE .......................................................... 5

2. GENERAL .......................................................................... 6

3. DISASSEMBLY

3-1. Loading Panel ....................................................................... 8

3-2. Front Panel ............................................................................ 8

3-3. Cassette Lid and Tape Mechanism........................................ 9

3-4. CD SW Board and Panel Board............................................9

3-5. Disc Tray.............................................................................10

4. SERVICE MODE ............................................................ 11

5. MECHANICAL ADJUSTMENTS ..........................14

6. ELECTRICAL ADJUSTMENTS ............................... 14

7. DIAGRAMS

7-1. Circuit Boards Location ...................................................... 18

7-2. Block Diagrams

• CD Section ....................................................................... 19

• Deck Section .................................................................... 21

• Main Section .................................................................... 23

• Main Power/Sub Power Section ...................................... 25

• Display Section ................................................................ 27

7-3. Printed Wiring Board – BD (CD) Section – ....................... 31

7-4. Schematic Diagram – BD (CD) Section – .......................... 33

7-5. Printed Wiring Board – Main Section – .............................. 35

7-6. Schematic Diagram – Main (1/4) Section – ........................ 37

7-7. Schematic Diagram – Main (2/4) Section – ........................ 39

7-8. Schematic Diagram – Main (3/4) Section – ........................ 41

7-9. Schematic Diagram – Main (4/4) Section – ........................ 43

7-10. Printed Wiring Board – Leaf SW Section – ..................... 45

7-11. Schematic Diagram – Leaf SW Section – ........................ 46

7-12. Schematic Diagram – Deck Section – .............................. 47

7-13. Printed Wiring Board – Deck Section – ........................... 49

7-14. Printed Wiring Board – Panel Section –........................... 51

7-15. Schematic Diagram – Panel (1/3) Section –..................... 53

7-16. Schematic Diagram – Panel (2/3) Section –..................... 55

7-17. Schematic Diagram – Panel (3/3) Section –..................... 57

7-18. Schematic Diagram – CD Motor Section –......................59

7-19. Printed Wiring Board – CD Motor Section – ................... 61

7-20. Schematic Diagram – Trans Section – ............................. 63

7-21. Schematic Diagram – Sub Trans Section – ...................... 65

7-22. Printed Wiring Board – Trans Section –........................... 67

7-23. Printed Wiring Board – Sub Trans Section – ................... 68

7-24. IC Block Diagrams ........................................................... 69

7-25. IC Pin Functions ............................................................... 70

8. EXPLODED VIEWS

8-1. Case Section........................................................................73

8-2. Chassis Section ................................................................... 74

8-3. Front Panel Section ............................................................. 75

8-4. CD Mechanism Deck Section-1 (CDM38LH-5BD32L) .... 76

8-5. CD Mechanism Deck Section-2 (CDM38LH-5BD32L) .... 77

8-6. Base Unit Section (BU-5BD32L) ....................................... 78

8-7. TC Mechanism Section-1 (TCM230AWR1/230PWR1) .... 79

8-8. TC Mechanism Section-2 (TCM230AWR1/230PWR1) .... 80

9. ELECTRICAL PARTS LIST ........................................ 81

– 4 –

Page 5

SECTION 1

SERVICING NOTE

HOW TO OPEN THE DISC TRAY WHEN POWER SWITCH TURNS OFF

Remove the Case.

Pull-out the disc tray.

Turn the cam to the direction

of arrow.

Note for Installation (ROTARY ENCODER)

BU cam

Groove

Section A

Note:When attaching the Base unit, Insert the section A into the groove of BU cam.

Note:When attaching the BU cam, engage the Rotary encoder switch as shown in the figure.

CD-TEXT

This unit is provided with a simple CD-TEXT display function. The CD-TEXT contents of 20 tracks are displayed on the fluorescent display tube. Since the function is simple, some special characters may not be displayed, or may be displayed as other characters.

– 5 –

Page 6

Front Panel

SECTION 2

GENERAL

23 4 7561

54 51

53 50

4142

61 60

59 58

9 10 11

4849

1715

44454647

3233

22 23

25 26

– 6 –

Page 7

LOCATION OF PARTS AND CONTROLS

1 1/u (Power) button and indicator 2 DEMO (STANDBY) POWER SAVE

button (RXD8/RXD8S) DEMO button (STANDBY) (GRX80)

3 DISC 1 button and indicator 4 DISC 2 button and indicator 5 DISC 3 button and indicator 6 DISC SKIP/EX–CHANGE button 7 § (Eject) button 8 Disc tray 9 EDIT DIRECTION/TUNER MEMORY

button

10 PLA Y MODE/DOLBY NR/PTY button

(RXD8/RXD8S) PLAY MODE/DOLBY NR button (GRX80)

11 REPEAT/STEREO/MONO button 12 p button 13 ^ (CD) button and indicator 14 TUNER/BAND button 15 NON-STOP button and indicator 16 KARAOKE PON/MPX button 17 SYNC EQ button

18 SYNC BASS button 19 REC PAUSE/START button and

indicator

20 DBFB button 21 SURROUND button 22 HI DUB button 23 CD SYNC button 24 VOLUME knob 25 PHONES jack 26 ENTER/NEXT button and indicator 27 ) + button and indicator 28 JOG/0x) dial and indicator 29 GROOVE button and indicator 30 –0 button and indicator 31 AUTO BPM button and indicator 32 PAD B button and indicator 33 PAD A button and indicator 34 MIX MIC jack 35 FLASH button 36 LOOP button 37 JAM button and indicator 38 LEVEL button 39 MIX button

40 MIC LEVEL knob 41 BEAT SPEED button 42 BEAT SELECT button 43 BEAT ON/OFF button and indicator 44 P FILE MEMORY button 45 GEQ CONTROL button 46 FILE SELECT 47 EFECT button 48 ( (B deck) button and indicator 49 9 (B deck) button and indicator 50 ( (A deck) button and indicator 51 9 (A deck) button and indicator 52 FUNCTION button 53 SYNC BASS H indicator 54 SYNC BASS L indicator 55 SYNC EQ indicator 56 EFECT indicator 57 Remote sensor 58 DISPLAY button 59 SPECTRUM ANALYZER button 60 CLOCK/TIME SET button 61 TIMER SELECT button and indicator 62 Display Window

This section is extracted from instruction manual.

– 7 –

Page 8

SECTION 3

)

DISASSEMBLY

Note: Follow the disassembly procedure in the numerical order given.

3-1. LOADING PANEL

Claws

Loading panel

Pull-out the disc tray.

Turn the cam to the direction

of arrow.

3-2. FRONT PANEL

Screw (BVTT3x6)

Front panel

Screw (BVTT3x6)

Flat type wire

(CN304)

Lead wire

Flat type wire

(CN303)

Screw

(BVTT3x6)

Flat type wire

(CN501)

Lead wire

Screw (BVTT3x6)

Screw (BVTT3x6

– 8 –

Page 9

3-3. CASSETTE LID AND TAPE MECHANISM

Release

Cassette holder (R)

assembly

Cassette holder (L)

assembly

Portion

Spring

T wo screws

(BVTP2.6x8)

Three screws

(BVTP2.6x8)

T ape mechanism

Spring

Release

(Refer to order No. 1)

Portion

)

3-4. CD SW BOARD AND PANEL BOARD

CD SW board

Knob (Jog)

Nut

Knob (Vol)

Three screws

(BVTP2.6x8)

Three screws

(BVTP2.6x8)

!™

Panel board

Flat type wire

(CN601)

Four screws

(BVTP2.6x8

Five screws

(BVTP2.6x8)

!¡

Five screws

(BVTP2.6x8)

– 9 –

Page 10

3-5. DISC TRAY

(Perform after removing the front panel.) Note:When installing the Disc tray, pull around the flat type wire to

Flat type wire (8 core)

Two claws

Pull-out the disc tray.

Remove the disc tray.

pass through the claw

Claw

and claw B, as shown in the figure.

Claw

Turn the cam the

direction of arrow.

– 10 –

Page 11

SECTION 4

SER VICE MODE

MC Cold Reset

• The cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the set to the customer.

Procedure:

1. Press three buttons p , ENTER/NEXT , and 1/u simultaneously.

2. “COLD RESET” is displayed on the fluorescent display tube and reset is executed.

CD Delivery Mode

• This mode moves the pick-up to the position durable to vibration. Use this mode when returning the set to the customer after repair.

Procedure:

1. Press 1/u button to turn the set ON.

2. Press LOOP button and 1/u button simultaneously.

3. A message “LOCK” is displayed on the fluorescent indicator tube, and the CD delivery mode is set.

MC Hot Reset

• This mode resets the set with the preset data kept stored in the memory . The hot reset mode functions same as if the po wer cord is plugged in and out.

Procedure:

1. Press three buttons p , ENTER/NEXT , and DISC 1 simultaneously.

2. The fluorescent indicator tube becomes blank instantaneously, and the set is reset.

Sled Servo Mode

• This mode can run the CD sled motor freely. Use this mode, for instance, when cleaning the pick-up.

Procedure:

1. Press 1/u button to turn the set ON.

2. Press three buttons p , ENTER/NEXT , and § simultaneously.

3. The Sled Servo mode is selected, if “CD” is blanking on the fluorescent indicator tube.

4. W ith the CD in stop status, When the 0 AMS ) knob is rotated in the clockwise direction, the pick-up moves outside. When rotated

counterclockwise, it moves inside.

5. To exit from this mode, perform as follows:

1) Move the pick-up to the most inside track.

2) Execute MC cold reset. (Press the three buttons p , ENTER/NEXT , and 1/u button simultaneously.)

Note:

• Always move the pick-up to most inside track when exiting from this mode. Otherwise, a disc will not be unloaded.

• Do not run the sled motor excessively, otherwise the gear can be chipped.

Change-over of AM Tuner Step between 9kHz and 10kHz

• A step of AM channels can be changed over between 9kHz and 10kHz.

Procedure:

1. Press 1/u button to turn the set ON.

2. Select the function “TUNER”, and press TUNER/BAND button to select the BAND “AM”.

3. Press 1/u button to turn the set OFF.

4. Pr ess ENTER/NEXT and 1/u buttons simultaneously , and the display of fluorescent indica tor tube changes to “ AM 9k STEP” or “ AM

10k STEP”, and thus the channel step is changed over.

LED and Fluorescent Indicator Tube All Lit, Key Check Mode

Procedure:

1. Press three buttons p , ENTER/NEXT , and DISC 2 simultaneously.

2. LEDs and fluorescent indicator tube are all turned on.

Press DISC 2 button, and the key check mode is activated.

3. In the k ey check mode, the fluorescent indicator tube displays “K 0 V0 J0”. Each time a button is pr essed, “K”value increases. Howe v er,

once a button is pressed, it is no longer taken into account. “J” Value increases like 1, 2, 3 ... if rotating 0 AMS ) knob in “+” direction, or it decreases like 0, 9, 8 ... if rotating in “-” direction. “V” Value increases like 1, 2, 3 ... if rotating VOLUME knob in “+” direction, or it decreases like 0, 9, 8 ... if rotating in “-” direction.

4. To exit from this mode, press three buttons in the same manner as step 1, or disconnect the power cord.

– 11 –

Page 12

AMS Test Mode

• This mode is used for checking the AMS operations of the tape deck.

JIG 7-819-039-12 Alignment tape, AMS-110A

Procedure:

1. Press the 1/u button to turn the unit ON.

2. Set the tape (AMS-110A).

3. Press the three buttons p , ENTER/NEXT , and DISC 3 button simultaneously.

4. “TEST MODE” is displayed on the fluorescent display tube.

5. Press the FUNCTION button and switch the function to the deck with the tape (AMS-110A).

6. Press the CD SYNC button. “AMS CHECK” is displayed on the fluorescent display tube and the tape is rewound.

7. AMS starts in the normal direction. If the AMS count is 2 at shut down, proceed to step 8. “NG” is displayed at other times, and the deck stops.

8. AMS starts in the opposite direction. If the AMS count is 2 at shut down again, “OK” is displayed. “NG” is displayed at other times.

Note:The p button of CD section will become ef fecti v e and the aging of CD section will stop sometime, if the b uttons described in ste p 3

are not pressed simultaneously. In that case, press ^ button and operate the CD section.

Aging Mode

During the aging mode, both the CD player and tape deck are executed together.

• If an error occurs:

Aging stops, and the error state is displayed on the fluorescent display tube.

• If no error occurs:

Aging is repeated.

Procedure:

1. Press the 1/u button to turn the unit ON.

2. Load 10 minute tapes with unbent rec-proof tabs in decks A and B.

3. Set CD on the DISC 1 table.

4. Set the CD mode REPEAT to OFF and PLAY MODE to ALL DISCS. (Press the PLAY MODE/DOLBY NR and REPEAT/STEREO/MONO buttons to set these modes.)

5. Press the FUNCTION button to switch the function to “CD”.

6. Press the three buttons p , ENTER/NEXT , and DISC SKIP/EX-CHANGE button simultaneously.

7. Aging starts.

8. To end aging, press the 1/u button to turn the unit OFF.

Aging Sequence:

Aging is performed in the following sequence.

• T ape Deck

1. The tape in deck A is rewound. “TAPE A AG-1” is displayed.

2. The FWD side of deck A is played for two minutes. “TAPE A AG-2” is displayed.

3. The tape in deck A is fast forwarded. “TAPE A AG-3” is displayed. Fast forward is carried out for 20 seconds or to the tape end.

4. The RVS side of deck A is played for two minutes. “TAPE A AG-4” is displayed.

5. The tape in deck A is rewound. “TAPE A AG-5” is displayed.

6. The FWD side of deck B is played for two minutes. “TAPE B AG-2” is displayed.

7. The tape in deck B is fast forwarded. “TAPE B AG-3” is displayed. Fast forward is carried out for 20 seconds or to the tape end.

8. The RVS side of deck B is played for two minutes. “TAPE B AG-4” is displayed.

9. The tape in deck A is rewound. “TAPE A AG-5” is displayed.

10. Repeated from step 2.

• CD

1. The tray rotates.

2. DISC 1 is chucked.

3. The TOC is read.

4. The first track is played for 2 seconds.

5. The last track is played for 2 seconds.

6. Repeated from step 1.

– 12 –

Page 13

• Display when ended abnormally When the tape deck is abnormal:

The state when ended abnormally is displayed. The contents of display are the same as that during aging.

When the CD player is abnormal:

A message indicating that errors such as “CD MEC ERR” have occurred. Check the error contents in the following error history display mode.

Error History Display Mode

Mode which enables the history of error occurring in the CD player to be checked. Execute this mode after ending the aging mode.

Procedure:

1. Press the 1/u button to turn the unit ON.

2. Press the three buttons p , ENTER/NEXT , and CD SYNC simultaneously.

3. A message such as “EMC@@EDC**” is displayed. @@ : Number of mechanical errors (Up to three past errors) ** : Number of errors (NO DISC ERROR) which occurs after chucking (Up to three past errors)

4. When checking the history of mechanical errors, press the PLAY MODE/DOLBY NR buttons. When checking errors after chucking, press the REPEAT/STERO/MONO buttons to switch the display.

5. Press the 1/u button to end and turn the unit OFF.

6. To erase the error history, perform COLD reset. (Press the three buttons p , ENTER/NEXT , and DISC 1 simultaneously.

• Viewing the mechanical error history display

(Switch the history by pressing the PLAY MODE/DOLBY NR button.)

Display E@@M**#*$*

@@ : Error number. 00 is the newest.

* : Invalid

# : Loading

D : Stop that is due to a problem of other than mechanism

during CLOSE mode.

E : Stop that is due to a problem of other than mechanism

during OPEN mode.

C : Stop that is due to a problem of other than mechanism

during CHUCK UP mode.

F : Stop that is due to a problem of other than mechanism

during EX OPEN mode.

$ : Emerging

1 : Stop during CLOSE mode. 2 : Stop during CHUCK DOWN mode. 3 : Time limit of EX OPEN mode. 5 : Time limit of EX CLOSE mode.

• Viewing the NO DISC ERROR history display (Switch the history by pressing the REPEAT/STERO/MONO buttons.)

Display E@@D##$$%*

@@ : Error number. 00 is the newest

## : Error contents

01 : Focus error 02 : GFS error 03 : Setup error

$$ : Retries

00 : NO DISC is determined without attempting chucking

retry

02 : NO DISC is determined after chucking retry.

% : State when determined as NO DISC

1 : When stopped 2 : At setup 3 : At TOC READ 4 : When accessing 5 : When playing 6 : When pausing 7 : When manual searching (during play) 8 : When manual searching (during pausing)

– 13 –

* : Invalid

Page 14

SECTION 5

MECHANICAL ADJUSTMENTS

SECTION 6

ELECTRICAL ADJUSTMENTS

Precaution

1. Clean the following parts with a denatured alcohol-moistened swab:

record/playback heads pinch rollers erase head rubber belts capstan idlers

2. Demagnetize the record/playback head with a head demagnetizer.

3. Do not use a magnetized screwdriver for the adjustments.

4. After the adjustments, apply suitable locking compound to the parts adjusted.

5. The adjustments should be performed with the rated power supply voltage unless otherwise noted.

Torque Measurement

Mode

FWD FWD

back tension REV

REV back tension

FF/REW

FWD tension

REV tension

Torque meter

CQ-102C

CQ-102RC

CQ-201B

CQ-403A

CQ-403R

Meter reading

31 to 71 g • cm

(0.43 – 0.98 oz • inch)

2 to 6 g • cm

(0.02 – 0.08 oz • inch)

31 to 71 g • cm

(0.43 – 0.98 oz • inch)

2 to 6 g • cm

(0.02 – 0.08 oz • inch)

71 to 143 g • cm

(0.98 – 1.99 oz • inch)

100 g or more

(3.53 oz or more)

100 g or more

(3.53 oz or more)

DECK SECTION 0 dB=0.775V

1. Demagnetize the record/playback head with a head damagnetizer .

2. Do not use a magnetized screwdriver for the adjustments.

3. After the adjustments, apply suitable locking compound to the parts adjusted.

4. The adjustments should be performed with the rated power supply voltage unless otherwise noted.

5. The adjustments should be performed in the order given in this service manual. (As a general rule, playback circuit adjustment should be completed before performing recording circuit adjustment.)

6. The adjustments should be performed for both L-CH and R-CH.

7. Switches and controls should be set as follows unless otherwise specified.

Signal

P-4-A100

WS-48B

P-4-L300

10 kHz, –10 dB

3 kHz, 0 dB

315 Hz, 0 dB

Record/Playback Head Azimuth Adjustment (Deck A, Deck B)

Note: Perform this adjustments for both decks.

Procedure:

1. Mode : Playback

Used forTape

Azimuth Adjustment

Tape Speed Adjustment

Level Adjustment

test tape P-4-A100 (10kHz, –10dB)

set

VIDEO IN

level meter

+ –

2. Turn the adjustment screw and check output peaks. If the peaks do not match for L-CH and R-CH, turn the adjustment screw so that outputs match within 1 dB of peak.

L-CH peak

screw position

R-CH peak

output level

within 1 dB

L-CH peak

R-CH peak

within 1dB

screw position

– 14 –

Page 15

3. Mode: Playback Tape Speed Adjustment (Deck A)

)

test tape P-4-A100 (10kHz, –10dB)

oscilloscope

MD OUT

Note: Set the test mode using the following method and begin tape

speed adjustment. In the test mode, the speed will switch to double speed or normal speed each time the HI DUB button is pressed.

set

Waveform of oscilloscope

in phase 45

good

135

wrong

180

4. After the adjustments, apply suitable locking compound to the parts adjusted.

Adjustment Location: Playback Head (Deck A)

Record/Playback/Erase Head (Deck B)

Procedure:

With the power turned ON, press the p button, ENTER/NEXT button, and DISC 3 button simultaneously. (The “CD TYPE INDICA T OR” on the fluorescent display tube will blink while in the test mode.) To exit the test mode, press the 1/u button.

1. Insert the WS-48B into deck B.

2. Press the ( button of deck B.

3. Press the HI DUB button and play the tape at double speed.

4. Adjust RV1001 of the LEAF SW board so that the reading of the frequency counter becomes 6000 ± 180 Hz.

5. Press the HI DUB button and play the tape at normal speed.

6. Adjust RV1002 of the LEAF SW board so that the reading of the frequency counter becomes 3000 ± 90 Hz.

Adjustment Location: LEAF SW board

Sample Value of Wow and flutter

W.RMS (JIS) less than 0.3% (test tape: WS-48B)

Playback Level Adjustment (Deck A, Deck B)

Procedure:

Mode: Playback

Reverse Foward

test tape P-4-L300 (315Hz, 0dB)

set

MD OUT

level meter

Deck A is RV311 (L-CH) and RV411 (R-CH), deck B is RV301 (L-CH) and RV401 (R-CH) so that adjustment within the following adjustment level.

Adjustment level:

CN301 playback level: 301.5 to 338.3 mV (–8.2 to –7.2 dB) level difference between the channels: within ± 0.5 dB Adjustment Location: AUDIO board

Adjustment Location [LEAF SW BOARD]

RV1001(High Speed) RV1002(Normal Speed

RV1002 RV1001

– 15 –

Page 16

Record Bias Adjustment (Deck B)

Record Level Adjustment (Deck B)

Procedure:

INTRODUCTION

When set to the test mode performed in Tape Speed Adjustment, when the tape is rewound after recording, the “REC memory

mode” which rewinds only the recorded portion and playback is set. This “REC memory mode” is convenient for performing this adjustment. During recording, the input signal FUNCTION will automatically switch to VIDEO. (After recording, press the – 0 button without stopping will return to the position where recording was started.)

1. Press FUNCTION button to select VIDEO. (This step is not necessary if the above test mode has already been set.)

2. Insert a tape into deck B, press the r REC button, and then press the ( button to start recording.

3. Mode: Record

VIDEO (AUDIO) IN

1) 315 Hz

2) 10 kHz

AF OSC

attenuator

600

Ω

} 50 mV (–23.8 dB)

blank tape CS-123

set

Procedure:

INTRODUCTION

When set to the test mode performed in Tape Speed Adjustment, when the tape is rewound after recording, the “REC memory

1. Press FUNCTION button to select VIDEO 1. (This step is not necessary if the above test mode has already been set.)

2. Insert a tape into deck B, press the r REC button, and then press the ( button to start recording.

3. Mode: Record

VIDEO (AUDIO) IN 315Hz 50 mV (–23.8 dB)

AF OSC

attenuator

600

Ω

set

blank tape CS-123

4. Mode: Playback

recorded position

set

MD OUT

level meter

5. Confirm playback the signal recorded in step 2 become adjustment level as follows. If these levels do not adjustment lev el, adjust the R V341 (L-CH) and R V441 (R-CH) on the A UDIO board to repeat steps 3 and 4.

Adjustment level: The playback output of 10 kHz le vel dif ference

against 315 Hz reference should be ± 1.0 dB.

Adjustment Location: AUDIO board

Adjustment Location:

[AUDIO BOARD] (Conductor Side)

RV341(Lch),RV441(Rch) Record Bias

RV301 RV401

RV441 RV341

RV311(Lch),RV411(Rch) Playback Level (Deck A)

RV411

RV311

4. Mode: Playback

recorded position

set

MD OUT

level meter

5. Confirm playback the signal recorded in step 2 become adjustment level as follows. If these levels do not adjustment lev el, adjust the R V301 (L-CH) and R V351 (R-CH) on the MAIN board to repeat steps 3 and 4.

Adjustment level:

CN403 playback level: 47.2 to 53.0 mV (–24.3 to –23.3 dB)

Adjustment Location: MAIN board

[MAIN BOARD] (Conductor Side)

Record Level (L CH) RV301

CN303

RV351 Record Level (R CH)

IC301

RV301(Lch),RV401(Rch) Playback Level (Deck B)

– 16 –

Page 17

SECTION 7

MAIN board

PANEL board

CD SW board

ENCAPSULATED COMPONENT (GRX80:E2.E3,EA3,AR,SP,TW,MX,AUS) TUNER unit (GRX80:EA4,TH/RXD8/RXD8S)

TRANS board

SUB TRANS board (RXD8/RXD8)

DIAGRAMS

HCD-GRX80/RXD8/RXD8S

CD SECTION

Note:

1. CD Block is basically constructed to operate without adjustment. Therefore, check each item in order given.

2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.

3. Use an oscilloscope with more than 10MΩ impedance.

4. Clean the object lens by an applicator with neutral detergent w hen the signal level is low than specified value with the following checks.

S Curve Check

oscilloscope

BD board

TP (FE) TP (VC)

Procedure :

1. Connect the oscilloscope to test points TP (FE) and TP (VC).

2. Connect TP (FEI) and GND, and TP (AGCCON) and GND of the BD board with lead wires.

3. Press the 1/u button to turn the set ON.

4. With the disc (YEDS-18) loaded, press the ^ button and perform focus search. (Focus search will be performed in the same way even while the disc table is pushed in and out.)

5. Check the symmetry and peak to peak level of the oscilloscope waveform (S curve) at this time.

+ –

Note: Clear RF signal waveform means that the shape “◊” can be

clearly distinguished at the center of the waveform.

RF signal waveform

VOLT/DIV : 200mV TIME/DIV : 500ns

level : 1.45 ± 3 Vp-p

E-F Balance (1 Track Jump) check

oscilloscope

BD board

TP (TE) TP (VC)

+ –

Procedure:

1. Connect oscilloscope to test point TP (TE) on BD board.

2. Press the 1/u button to turn the unit ON.

3. Put disc (YEDS-18) in to play the number five track.

4. Press the ^ button.

5. Check the le vel B of the oscilloscope's wa veform and the A (DC voltage) of the center of the Traverse waveform. Confirm the following:

• A/B x 100 = less then ± 22 (%)

• B = 1.3 ± 0.6 Vp-p

7-1. CIRCUIT BOARDS LOCATION

ENCAPSU LA TED COMPONENT/TUNER unit is supplied as the assembled block.

S-curve waveform

symmetry

Within 4

1 Vp-p

6. After check, remove the lead wire connected in step 2. Note: • Try to measure several times to make sure than the ratio of

A : B or B : A is more than 10 : 7.

• Tak e sweep time as long as possible and light up the brightness to obtain best waveform.

RF Level Check

oscilloscope

BD board

TP (RF) TP (VC)

+ –

Procedure :

1. Connect oscilloscope to test point TP (RF) and TP (VC) on BD board.

2. Connect TP (AGCCON) and GND of the BD board with lead wires.

3. Press the 1/u button to turn the set ON.

4. Put disc (YEDS-18) in and playback 5track.

5. Confirm tha t oscilloscope waveform is clear and check RF signal level is correct or not.

6. After check, remove the lead wire connected in step 2.

1 track jump waveform

level : 1.3

0.6 Vp-p

Adjustment Location :

[ BD BOARD ] — SIDE A —

TP (VC)

TP (RF)

TP (AGCCON)

TP (FE)

TP (TE)

TP (FE1)

Center of the waveform

A (DC voitage)

Symmetry

CONNECTOR board

MOTOR (TURN) board

BD board

SENSOR board

MOTOR (SLIDE) board

LEAF SW board

AUDIO board

– 17 –

– 18 –

Page 18

HCD-GRX80/RXD8/RXD8S

7-2. BLOCK DIAGRAMS

– CD SECTION –

OPTICAL PICK-UP BLOCK

B+

LASER DIODE

DETECTOR

IC381

D.OUT

FOCUS/TRACKING SERVO.

RF AMP

IC101 (1/2)

1 4 2 5

LD DRIVE

Q101

38 39

41 42

3637LD

PD1

PD2

FEI

FEO TEO

TEI

SENS1

SENS2

XRST

RF O

LOCK

C.OUT

FE O FE M

TA M

TA O

DATA

XLT CLK

FOK

19 24 25

12 13

22 21 20

LOCK

CNIN

SEIN

DATAO

XLTO

15 16 17

CLKO

DOUT

MDP

FOK

SPOD

S101

LIMIT

IC381

CD DIGITAL

OUT

OPTICAL

DIGITAL SIGNAL PROCESSOR

IC103

CLOK

XLAT

DATA

10 11 12 75

SQCK

SENS

SCOR

SQSO

79 100

XRST

89 • 90

XTAI

LOUT1

LOUT2

16.9344MHz

• XTAO

X101

L-CH

R-CH

CD CLK

CD DATA

SENS2

SCOR SQ DATA

SQ CLK

SENS

M102

SLED MOTOR

M101

SPINDLE

MOTOR

XRST

TRACKING

FOCUS

COIL

•

COIL

2-AXIS

DEVICE

SLED/SPINDLE MOTOR DRIVE

IC102 (2/2)

SLED MOTOR

DRIVE

SPINDLE MOTOR

DRIVE

T+

–

F F+

18 17

MUTE

TRACKING

COIL DRIVE

FOCUS/TRACKING

COIL DRIVE

IC102 (1/2)

FOCUS

COIL DRIVE

SLED

SERVO

IC101 (2/2)

SL P

SL O

S801

DET

TABLE

SENSOR

IC702

DISC

SENSOR

IC703

ROTARY

ENCODER

S811

Q701

TURN

MOTOR DRIVER

IC701

M701

1416

TURN

MOTOR

M801

SLIDE

MOTOR

OUT1

OUT2

4 7

MOTOR DRIVER

OUT2 OUT1

SLIDE

IC801

IN1 IN2

RIN FIN

OPEN/CLOSE

3 6

XLAT

TRAY SENS

DISC SENS

ENC 1 ENC 2

ENC 3

OUT-OPEN

TBL.L TBL.R

LD IN

LD OUT

MAIN

SECTION

(Page 23)

• R CH: Same as L ch

• SIGNAL PATH : CD : Digital out

– 19 –

– 20 –

Page 19

– DECK SECTION –

HCD-GRX80/RXD8/RXD8S

HP101 PB HEAD (DECK A)

REC/PB HEAD

(DECK B)

HRPE101

ERASE HEAD

PB A/B

MS OUT

MAIN SECTION

PB L

LM ON/OFF

NORM/HIGH

NR ON/OFF

REC/PB/PASS

REC L

BIAS ON/OFF RM ON/OFF

ALC ON/OFF

RELAY

CAPM CNT1

CAPM CNT2

CAP M H / L

A SHUT

MAIN

SECTION

(Page 23)

DOLBY NR

RECOUT

32 33

S1008 B CrO

B 120/70

PAS

BIAS SW

DOL

DOLBY TYPE B

CAPSTAN

MOTOR

PB OUT

LM ON/

OFF

NORM/

HIGH

NR ON/

OFF

RIN

BIAS ON/OFF

RM ON/OFF

ALC ON/OFF

CAP MOTOR CONTROL Q336-343

CONTROL

RV1002

NORMAL

SPEED

Q1001

20 22 15

RV1001

HIGH

SPEED

SWITCH

Q335

REEL

DETECT

IC1001

S1004 A CrO

RV311

PLAYBACK

LEVEL

DECK A

RV301

PLAYBACK

LEVEL

DECK B

RV341

REC

BIAS

REC BIAS

BIAS OSC

T621, Q621, 622

IC611

R CH

ERASE BIAS

IC601

IC602

REC/PB

PB-A/B

A IN

B IN

REC LEVEL

+7.5V

Q623

EQIN

EQOUT

RV301

A 120/70

120

DOLBY NR IC301

REEL

DETECT

IC1002

S1001 (A PLAY)

• R CH : Same as L ch

• SIGNAL PATH

+5V

S1002 (B PLAY)

: PB (DECK A) : PB (DECK B) : REC (DECK B)

• PLUNGER SOLENOID is supplied as the MECHANICAL BLOCK ASSY.

A DECK/ B DECK PLUNGER

MAIN SECTION

TRIGGER MOTOR CONTROL Q331-334

S1003

(A HALF)

S1005

(REC A)

S1006

(B HALF)

S1009

(REC B)

+5V

B SHUT

A PLAY

B PLAY

A HALF

B HALF/REC A/REC B

B TRIG

A TRIG

– 21 – – 22 –

Page 20

HCD-GRX80/RXD8/RXD8S

– MAIN SECTION –

J711 MIX MIC

(Page 28)

DISPLAY

SECTION

VIDEO/IN

(AUDIO) L

MD IN L

MD/VIDEO

(AUDIO) OUT L

DJ-SIG

DJ-MUTE

J101

PB L

REC L

IC712(1/2)

RV712

MIC

LEVEL

GRX80:EA3

ECHO PROCESSOR IC711

LPF 1 IN LPF 2 OUT

ECHO LEVEL

IC712(2/2)

IC181(1/2)

GRX80:EA3

MUTE

Q181

SELECT SWITCH

MICON INTERFACE

33 32

1 2 3

IC181(2/2)

230

R-CH

EQ IC101(1/2)

EQ AMP

SPE SIG

WAKE UP STANDBY LED

IIC DATA

VOLUME IC101(2/2)

Lch

38 39

DBFB SWITCH Q111,112

Lch

MUTE

Q113

Q201

MUTE

Q191

J191

SUPER WOOFER

IIC CLK TIMER LED RESET

FRONT

DBFB

DISPLAY SECTION

(Page 27)

DECK

SECTION

(Page 22)

FM/AM TUNER TUNER UNIT IS SUPPLED AS THE ASSEMBLED BLOCK

SECTION

(Page 20)

RELAY

A SHUT

B HALF/REC A/REC B

B SHUT

A HALF A PLAY B PLAY

PB A / B

NORM/HIGH

BIAS ON/OFF

RM ON/OFF NR ON/OFF

REC/PB PASS

CAPM CNT1 CAPM CNT2

ALC ON/OFF

LM ON/OFF

CAP M H/L

A TRG B TRG

MS OUT

ST L

RDS DATA

RDS INT

ST-DOUT

ST-DIN

STEREO

TUNED

ST CE

ST-MUTE

ST-CLK

L CH

TBL. L TBL. R

SCOR

TRAY SENS

HOLD SENS

X RST

CD CLK

CD DATA

DISC SENS

SQ CLK

SQ DATA

X LAT

OUT-OPEN

ENC-1 ENC-2 ENC-3

LD IN

LD OUT

1 2 3

100

TC RELAY A SHUT

B SHUT

B HALF

A HALF

A PLAY SW

B PLAY SW

PB A/B

EQ H//N BIAS

82 81

REC MUTE

NR ON/OFF

R/PB PASS

CAPM CNT1

CAPM CNT2

ALC

TC MUTE

CAP M H/L

A TRG

B TRG

AMS IN

493-LAT

493-DATA

493-CLK

ST DIN

54 50

STEREO TUNED

51 52

ST CE

ST MUTE

ST DOUT ST CLK

TBL L

TBL R

SCOR

T SENS

HOLD

SENS

XRST

CD CLK

CD DATA

DISC SENS

SQ CLK

SQ DATA

XLT

OUT OPEN

ENC1

ENC2/DISC-LED

ENC3/UP-SW

LOAD IN

LOAD OUT

RDS DATA RDS INT

RXD8, RXD8S

MASTER CONTROL

IC501

BASS FRQ.

DBFB H/L

LINE MUTE

F RELAY

WAKE UP

ST-BY LED/CLOCK OUT

IIC DATA

IIC CLK

TIMER LED

RESET

AC CUT

(CHECK)

X-OUT

X-IN

XC-IN

XC-OUT

RY-SW

POWER

CD POWER

FL SW

STBY RELAY

STK MUTE

PROTECTOR

7 6

18 39

30 29

D503

RESET

SWITCH

Q501

RESET

IC502

+5.6V

X613

16MHz

X601

32.768KHz

MUTE SW

Q509

MUTE SW

Q508

MUTE

Q192

F RELAY

POWER

SECTION

(Page 25)

• R CH: Same as L ch

• SIGNAL PATH

RY-SW

: FM : CD

42 43

POWER ON/OFF

CD POWER

FL SW ON/OFF STANDBY RELAY

ON/OFF

STK MUTE

PROTECTOR

: PB : REC : VIDEO/MD

• Abbreviation EA3 : Saudi Arabia model.

– 23 –

– 24 –

Page 21

– MAIN POWER/SUB POWER SECTION –

F RELAY

FRONT

VH+

DBFB

STK MUTE

RY-SW

PROTECTOR

MAIN

SECTION

D+5V UNSW

(Page 24)

POWER ON/OFF

CD D+5V (SW)

CD A+5V (SW)

CD POWER

FL SW ON/OFF

VH+ SUPP Q803, 881

RECTIFIER

+5.6V (STBY)

+5V (STBY)

(DISPLAY)

+5V REG

Q907

SWITCH

D507

Q908

D509

POWER AMP

IC801

18 14

MUTE

SWITCH

Q804

RECTIFIER

D925

+5V OUT

Q911

SWITCH

Q912

THERMAL

Q831, 832

OVER LOAD

Rch

Q412, 411

JW51

RDS D+5V UN SW

+5V (LED) (DISPLAY)

D+5V

SWITCH

Q904

SWITCH

Q923, 903

IC904

3 1

REG

ST+10V

DET

THP831

Lch

DET

Q801

MUTE

SWITCH

RECTIFIER

D922

RECTIFIER

D924

+5V OUT

Q905

A+7V

A–7V

CD MOTOR +7V

TC MOTOR +12V

+10V REG

Q909

Rch

VH+

Rch

IC902

3 1

REG

+7V REG

Q901,902,913

–7V REG

Q951,952,914

IC901

3 1

+7V REG

IC903

3 1

+12V REG

RY401

PROTECT CONTROL

Q432 - 434

+VH

–VH

+VL

–VL

Q435, 436, 431

RECT D831

RECT D832

RECT

D901-904

RECT

D907-910

RELAY

DRIVE

SWITCH

Q437

POWER TRANSFORMER

AC1

AC2

AC2 AC1

AC3

AC4

MUTE

SWITCH

Q439

T951

DISPLAY

(VIA POWER)

GRX80:E2,E3,EA3,SP,AR,TW

VOLTAGE

SELECTOR

S951

Rch

SUB TRANS. D+5.6V

COM MON

FAN MOTOR

DRIVER

Q401, 402

FRONT

3 1

Rch

IC11

5.6V REG

-26V REG Q12, 13

SWITCH

Q16, 17

UNREG –7V

RXD8,RXD8S

J701

PHONES

RECT

D12-15

RECT

D17-20

VF BUFF Q14, 15

RELAY DRIVE

Q11

TM402 SURROUND

SPEAKER

M901 FAN MOTOR

TM401

FRONT

SPEAKER

T11

SUB TRANSFORMER

RY11RY11

HCD-GRX80/RXD8/RXD8S

• R CH : Same as L ch

• SIGNAL PATH : FM

• Abbreviation : Without SW tuner E model.

: Without SW tuner E model.

: Saudi Arabia model.

EA3

: Singapore model.

: Malaysia model.

: Hong Kong model.

: Taiwan model.

:Argentine model.

RXD8,RXD8S

Q11

GRX80

STANDBY RELAY ON/OFF

– 25 –

– 26 –

Page 22

HCD-GRX80/RXD8/RXD8S

– DISPLAY SECTION –

LED SWITCH

Q607

D637

RIGHT

+5V (LED)

MAIN

SECTION

(Page 24)

IIC DATA

IIC CLK

RESET

WAKE UP

X601

12.5MHz

C DATA

I2C CLK

RESET

XOUT

XIN

GRADATION R/WAKE UP

DISPLAY CONTROL

SEG1-SEG22

GR2-GR12

33 - 40, 42 - 4446 - 67

FLUORESCENT INDICATOR TUBE

IC601

FL601

GRADATION L

L/P SCK

LED LA

L/P DAT

L SEL

SIRCS

S LOW (F01)

BPF1 (F02)

ALL B (L+R)

JOG A JOG B

Busy for PAD

PAD LA

CH for PAD

VOL A VOL B

GR1, GR13-GR18

27 - 32, 45

IND BUFF

Q610-616

BPF2 BPF3 BPF4

KEY 0

KEY 3

IC604

3 4 5

1 16 17 18 19

LED

SWITCH

ROTARY

ENCODER

S602

VOLUME

LED SWITCH

Q608

• 7

•

LED

CONTROL

Q603

REMOTE

CONTROL

RECEIVER

IC602

S601 (JOG)

ROTARY

ENCODER

KEY

MATRIX

PANEL LED

D638

LEFT

Q601,602

+5V (LED)

SOUND MIX

IC605

BUSY

XT XT

X602

4.09MHz

A.OUT

MUTE SWITCH Q851

DJ MUTE

DJ SIG

MAIN

SECTION

(Page 23)

SPEANA BPF FILTER

IC603

S LOW

F01

BPF1

F02

16 F04 F05 F06 L+R

BPF2

BPF3

BPF4

ALLB

D804

ECO

D635

TIMER SELECT

LINE IN

REC IN

+5V (LED)

SPE SIG

STANDBY LED

TIMER LED

LED SWITCH

Q605

– 27 – – 28 –

Page 23

HCD-GRX80/RXD8/RXD8S

2.5V

APPROX 500mVp-p (PLAY)

2.5V

APPROX 200m Vp-p (PLAY)

THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.)

For schematic diagrams.

Note:

• All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums.

• All resistors are in Ω and 1/ specified.

•

: internal component.

• C : panel designation.

Note: The components identified by mark ! or dotted line

with mark ! are critical for safety. Replace only with part number specified.

• U : B+ Line.

• V : B– Line.

• H : adjustment for repair.

• Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions.

• Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage var iations may be noted due to normal production tolerances.

• Waveforms are taken with a oscilloscope. Voltage var iations may be noted due to normal production tolerances.

• Circled numbers refer to waveforms.

• Signal path.

F : FM f : AM g : VIDEO/MD E : PB (DECK A) d : PB (DECK B) G : REC (DECK B) J : CD c : digital out

• Abbreviation G : German model. E2 : Without SW tuner E model. E3 : With SW tuner E model. EA3 : Saudi Arabia model. EA4 : Israeli model. AUS : Australian model. SP : Singapore model. TW : Taiwan model. AR : Argentine model. TH : Thailand model. MX : Mexican model.

W or less unless otherwise

WAVEFORMS – BD (CD) SECTION –

16.9MHz

IC101 ^§ XTAI

(PLAY)

IC101 %¡ RF AC

IC101 $¡ TE

IC101 #ª FE

7.5µsec

IC101 @§ MDP

3.1Vp-p

1.2Vp-p

2.4Vp-p

– MAIN (3/4) SECTION –

5.2Vp-p

32.768kHz

IC501 !¡ XC-OUT

5.5Vp-p

16MHz

IC501 !£ X-OUT

– PANEL (2/3) SECTION –

3.4Vp-p

12.5MHz

IC601 &™ X OUT

3.6Vp-p

4.09MHz

IC605 2 XT

For printed wiring boards.

Note:

• X : parts extracted from the component side.

• p : parts mounted on the conductor side.

•

• b : Pattern from the side which enables seeing.

(The other layers' patterns are not indicated.)

• Indication of transistor

: Through hole.

These are omitted

– 29 – – 30 –

Page 24

HCD-GRX80/RXD8/RXD8S

7-3. PRINTED WIRING BOARD – BD (CD) SECTION –

• See page 18 for Circuit Boards Location.

(VC)

(RP)

(AGCCON)

(FE)

(TE)

(FF1)

(Page 36)

– 31 –

– 32 –

Page 25

7-4. SCHEMATIC DIAGRAM – BD (CD) SECTION –

• See page 30 for Waveforms.

HCD-GRX80/RXD8/RXD8S

(TE)

(FE)

(RP)

(Page 37)

220

19P

TP (AGCCON)

(VC)

– 33 –

10V

– 34 –

Page 26

HCD-GRX80/RXD8/RXD8S

7-5. PRINTED WIRING BOARD – MAIN SECTION –

• See page 18 for Circuit Boards Location.

• Semiconductor Location

Ref. No. Location D141 E-10

D191 E-10 D331 E-1 D334 E-1 D335 F-1 D401 G-11 D403 F-12 D405 H-6 D406 I-4 D407 I-2 D411 G-3 D501 D-7 D502 E-6 D503 D-6 D504 D-7 D505 D-7 D506 D-7 D509 F-2 D607 E-5 D644 C-8 D801 J-11 D802 G-9 D803 G-11 D831 I-6 D832 J-7 D851 J-10 D852 G-9 D881 H-9 D901 J-4 D902 I-4 D903 J-4 D904 I-4 D905 I-1 D906 H-1 D907 J-5 D908 I-5 D909 J-5 D910 J-5 D915 I-4 D921 H-4 D922 G-4 D923 G-4 D924 F-2 D925 G4 D971 ?

IC101 B-10 IC181 D-11 IC301 B-3 IC381 A-12 IC501 D-5 IC502 D-7 IC801 G-10 IC901 G-6 IC902 G-4 IC903 I-4

Q111 D-10 Q112 D-10

Ref. No. Location

Q113 E-9 Q161 C-9 Q162 C-9 Q163 E-9 Q181 E-11 Q191 E-10 Q192 E-10 Q201 D-9 Q251 C-9 Q331 C-1 Q332 C-2 Q333 C-2 Q334 C-2 Q335 D-1 Q336 F-1 Q337 F-1 Q338 F-1 Q339 F-1 Q340 E-1 Q341 E-1 Q342 E-1 Q343 E-1 Q401 F-12 Q402 E-12 Q411 G-2 Q412 G-2 Q431 G-12 Q432 G-11 Q433 F-11 Q434 F-11 Q435 F-11 Q436 F-11 Q437 G-12 Q439 F-12 Q471 F-12 Q501 D-7 Q508 D-7 Q509 E-7 Q801 H-10 Q803 G-10 Q804 G-9 Q831 G-10 Q832 G-10 Q851 J-11 Q881 I-9 Q901 H-2 Q902 I-1 Q903 H-1 Q904 G-4 Q905 G-4 Q907 G-5 Q908 G-4 Q909 I-4 Q913 H-1 Q914 G-2 Q923 H-1 Q951 G-2 Q952 H-1

(Page

49)

(Page 45)

(Page 51)

(Page 68)

(Page

67)

(Page 61)

(Page 61) (Page 32)

(Page 67)

– 35 – – 36 –

Page 27

7-6. SCHEMATIC DIAGRAM – MAIN (1/4) SECTION –

(Page 33)

(Page 60)

(Page 41)

(Page 42)

(Page 43)

(Page

39)

(Page

39)

HCD-GRX80/RXD8/RXD8S

– 37 –

– 38 –

Page 28

HCD-GRX80/RXD8/RXD8S

7-7. SCHEMATIC DIAGRAM – MAIN (2/4) SECTION –

• See page 35 for Printed Wiring Board.

(Page

42)

(Page

38)

(Page

42)

(Page 43)

(Page 44)

– 39 – – 40 –

(Page 63)

Page 29

7-8. SCHEMATIC DIAGRAM – MAIN (3/4) SECTION –

• See page 30 for Waveforms.

• See page 35 for Printed Wiring Board.

• See page 70 for IC Pin Functions.

HCD-GRX80/RXD8/RXD8S

(Page 37)

(Page 38)

(Page 39)

(Page 43)

(Page 48)

(Page 43)

(Page 46)

– 41 –

– 42 –

Page 30

HCD-GRX80/RXD8/RXD8S

7-9. SCHEMATIC DIAGRAM – MAIN (4/4) SECTION –

• See page 35 for Printed Wiring Board.

(Page 38)

(Page

42)

(Page 39)

(Page 39, 40)

(Page 40)

(Page

42)

(Page

42)

(Page

42)

(Page 63)

(Page 56)

(Page 63)

– 43 – – 44 –

Page 31

7-10. PRINTED WIRING BOARD – LEAF SW SECTION –

• See page 18 for Circuit Boards Location.

7-11. SCHEMATIC DIAGRAM – LEAF SW SECTION –

HCD-GRX80/RXD8/RXD8S

(Page 35)

– 45 –

(Page 41)

– 46 –

Page 32

HCD-GRX80/RXD8/RXD8S

7-12. SCHEMATIC DIAGRAM – DECK SECTION –

(Page 41)

– 47 – – 48 –

Page 33

7-13. PRINTED WIRING BOARD – DECK SECTION –

• See page 18 for Circuit Boards Location.

HCD-GRX80/RXD8/RXD8S

23456789101112

(Page 35)

– 49 –

– 50 –

Page 34

HCD-GRX80/RXD8/RXD8S

• Semiconductor Location

Ref. No. Location D601 F-6

D608 C-9 D609 C-2 D611 C-6 D612 C-7 D613 C-5 D614 C-4 D615 E-4 D619 D-3 D620 E-1 D621 G-7 D622 G-4 D623 G-7 D624 E-5 D625 E-4 D626 E-7 D627 G-9 D628 G-8 D629 F-9 D630 F-8 D631 D-6 D632 D-5 D633 D-8 D634 D-7 D635 A-9 D701 E-9

7-14. PRINTED WIRING BOARD – PANEL SECTION –

• See page 18 for Circuit Boards Location.

(Page 35)

IC601 B-5 IC602 C-9 IC603 B-7 IC604 F-5 IC605 C-4 IC711 E-8 IC712 G-8

Q601 F-6 Q602 F-6 Q603 F-6 Q604 A-10 Q605 A-10 Q607 B-2 Q608 C-9 Q610 B-7 Q611 B-7 Q612 B-7 Q613 B-7 Q614 B-7 Q615 B-8 Q616 B-8 Q620 A-10

– 51 – – 52 –

Page 35

7-15. SCHEMATIC DIAGRAM – PANEL (1/3) SECTION –

• See page 69 for IC Block Diagrams.

HCD-GRX80/RXD8/RXD8S

(Page 57)

– 53 –

(Page 57)

(Page 55)

– 54 –

Page 36

HCD-GRX80/RXD8/RXD8S

7-16. SCHEMATIC DIAGRAM – PANEL (2/3) SECTION –

• See page 30 for Waveforms.

• See page 51 for Printed Wiring Board.

• See page 69 for IC Block Diagrams.

• See page 72 for IC Pin Functions.

(Page

53, 54)

(Page 58)

– 55 – – 56 –

(Page 43)

(Page 58)

Page 37

7-17. SCHEMATIC DIAGRAM – PANEL (3/3) SECTION –

• See page 51 for Printed Wiring Board.

• See page 69 for IC Block Diagrams.

HCD-GRX80/RXD8/RXD8S

(Page

53)

(Page 55)

(Page 56)

(Page

53)

– 57 –

– 58 –

Page 38

HCD-GRX80/RXD8/RXD8S

7-18. SCHEMATIC DIAGRAM – CD MOTOR SECTION –

1SS119

MTZJ-T-72-5.6C (M)

(Page 37)

1SS119

(Page 37)

MTZJ-T-72-3.6C (M)

– 59 – – 60 –

Page 39

7-19. PRINTED WIRING BOARD – CD MOTOR SECTION –

• See page 18 for Circuit Boards Location.

(Page 35)

HCD-GRX80/RXD8/RXD8S

(Page 36)

– 61 –

– 62 –

Page 40

HCD-GRX80/RXD8/RXD8S

7-20. SCHEMATIC DIAGRAM – TRANS SECTION –

• See page 67 for Printed Wiring Board.

(Page 40)

(Page 65)

(Page 43)

– 63 – – 64 –

Page 41

7-21. SCHEMATIC DIAGRAM – SUB TRANS SECTION – (RXD8/RD8S ONLY)

• See page 68 for Printed Wiring Board.

(Page 64)

HCD-GRX80/RXD8/RXD8S

(Page 43)

– 65 –

– 66 –

Page 42

HCD-GRX80/RXD8/RXD8S

7-22. PRINTED WIRING BOARD – TRANS SECTION –

• See page 18 for Circuit Boards Location.

7-23. PRINTED WIRING BOARD – SUB TRANS SECTION – (RXD8/RXD8S ONLY)

• See page 18 for Circuit Boards Location.

(Page 68)

(Page 67)

• Semiconductor Location

Ref. No. Location D11 C-2

D12 C-2 D13 C-2 D14 C-2 D15 C-2 D16 E-3 D17 D-2 D18 D-2 D19 D-2 D20 D-2 D21 D-2 D22 D-1 D23 D-1

IC11 D-3 Q11 D-2

Q12 D-2 Q13 D-2 Q14 D-1 Q15 D-1 Q16 D-1 Q17 D-1

(Page 35)

– 67 – – 68 –

Page 43

7-24. IC BLOCK DIAGRAMS

• PANEL (1/3) section

IC603 BA3830F

REFFERENCE

CURRENT

REFFERENCE

CURRENT

Bias

R02

P01

LINE

REC

RESET

BIAS

GND1

• PANEL (2/3) section

BPF

RESET

DET

• PANEL (3/3) section

IC604 NJU3716M

DATA

CLK

STB

CLR

LATCH

SHIFT REGISTER

CONTROL

RESET

f01

f02

f03

f04

f05

f06

REC LEVEL

VCC

P10

P11

P12

P13

P14

P15

P16

IC605 MSM6654A-540GS-K

SW3 SW2 SW1 SW0

TEST

RND

BUSY

OSC1 OSC2 OSC3

14 13

12 11 10

2 3 5

ADDRESS

SWITCHING

CONTROLLER

RANDOM

CIRCUIT

I/O

INTERFACE

OSC

(XT/CR)

XT/CR

17 STAGE (MSM6654A)

MULTIPLEXER

17 STAGE (MSM6654A)

ADDRESS COUNTTER

TIMING CONTROLLER

RESET

VDD

GND

1M BIT ROM EDITING ROM & ADDRESS ROM

CONTAINS 22KBIT

DATA

CONTROLLER

MELODY

GENERATOR

BEEP TONE

GENERATOR

ADPCM

SYNTHESIZER

PCM

SYNTHESIZER

12 BIT

DAC

LPF

AOUT

– 69 –

Page 44

7-25. IC PIN FUNCTIONS

• IC501 MASTER CONTROL (M306622 MA-A01FP)

Pin No.

1 STK-MUTE O Power amp ON/OFF signal output 2 POWER O Power ON/OFF signal output 3 F-RELAY O Front speaker relay control output 4 REAR-RELAY O Rear speaker relay control output (Not used) 5 CD-POWER O CD power on signal output 6 LINE-MUTE O Line mute ON/OFF selection output 7 DBFB-H/L O DBFB H/L select signal output

8, 9 – – Not used

10 XC-IN I 11 XC-OUT O 12 RESET I Reset signal input 13 X-OUT O X’tal (16MHz) 14 VSS – Ground 15 X-IN I X’tal (16MHz) 16 VCC – Power supply (+5V) 17 NMI I Not used (PULL UP EVER+5V) 18 WAKE UP I WAKE UP (Fixed at fixed at “L”) 19 SCOR I Subcode data request signal output 20 RDS-INT I 21 RDS-DATA I 22 AC-CUT I Back up signal input 23 PL-CLK O Clock signal to pro-logic (Not used) 24 PL-DATA O Data signal to pro-logic (Not used) 25 PL-LAT O Latch signal to pro-logic (Not used) 26 TIMER LED I Timer LED ON/OF 27 PROTECT OR I Speaker protect ON/OF 28 – – Not used 29 IIC-CLK O Clock output for IC601 30 IIC-DATA O Data output for IC601 31 – – Not used 32 SQ-DATA I 33 SQ-CLK I 34 SW-MODE O Not used 35 CD-DATA O CD data output 36 RY-SW I Head phone swich detect 37 CD-CLK O CD clock output 38 493-LAT O Latch signal output for M62493FP (IC101)

40 L+R/L-R I 41 BY-PASS I 42 FL-SW I FL switch ON/OFF 43 STBY RELAY I Stand by relay ON/OFF 44 BASS FREQ O FREQ high/low signal for SYNC bass

45, 46 – – Not used

47 493-DATA O Data output for M62493FP (IC101) 48 493-CLK O Clock output for M62493FP (IC101) 49 ST-MUTE O Tuned mute signal output

Pin Name I/O Function

X’tal (32.768MHz)

RDS data interrupt input

Subcode Q data clock input

ST-BY LED/ CLOCK-OUT

O Clock ond stand by LED signal output

Not used

– 70 –

Page 45

Pin No.

50 STEREO I Stereo detection for tuner 51 TUNED I Tuned detection for tuner 52 ST-CE O Tuner chip enable output 53 ST-DOUT O Tuner data output 54 ST-DIN I Tuner data input 55 ST-CLK O Tuned clock output 56 SENS I BD Condition signal input 57 HDLD O Mode hold signal output 58 XLT O CD latch signal output 59 XRST O CD reset signal output 60 DISC-SENS I Slit sensor of disc table input 61 T-SENS I CD table detection signal input 62 VCC – Power supply (+5V) 63 TBL-L O Table motor control output 64 VSS – Ground 65 TBL-R O Table motor control output 66 LOAD-OUT O 67 LOAD-IN O 68 ENC 3/UP-SW I 69 ENC 2/DISC-LED I 70 ENC 1 I 71 OUT-OPEN O Loading out detection signal output 72 B-TRG O 73 A-TRG O 74 CAP-M-COT2 O Capstan motor control 1(-) signal output 75 CAP-M-COT1 O Capstan motor control 2(-) signal output 76 CAP-M-H/L O Capstan motor H/L speed select signal output 77 AMS-IN I Connected to ground 78 TC-MUTE O TC mute ON/OFF selection output 79 R/PB/PAS O REC/PB/PASS selection output 80 NR-ON/OFF O NR ON/OFF signal output 81 REC-MUTE O REC mute ON/OFF selection output 82 BIAS O Bias ON/OFF selection output 83 EQ-H/N O Equalizer H/N select output 84 PB-A/B O PB Deck A/Deck B select output 85 ALC O ALC ON/OFF output 86 B-PLAY-SW I Deck B play detect 87 A-PLAY-SW I Deck A play detect 88 A-HALF I Deck A cassette detect 89 B-HALF I Deck B cassette detect 90 B-SHUT I B Deck reel pulse detector 91 A-SHUT I A Deck reel pulse detector 92 SOFT-TEST O Software test port

93, 94 KEY/CD-ADJ I CD adjust point port

95 MODEL IN I Version select signal input 96 AVSS – Ground 97 SPEC-IN I Version select signal input 98 VREF I Analog reference voltage input 99 AVCC – Analog power supply

100 TC-RELAY O REC/PB head selection output for IC602

Pin Name

I/O Function

Loading motor control signal output

Disc tray address detect encoder input

Trigger motor control output

– 71 –

Page 46

• IC601 DISPLAY CONTROL (TMP88CS76F-6000)

Pin No.

1 SIRCS I Remote commander signal input 2 JOG A I Rotary encoder (S601) pulse input 3 L/P SCK O LED/PAD clock output 4 LED LA O LED latch output 5 L/P DAT O LED/PAD data output 6 PAD LA O PAD latch output 7 L SEL O LED select signal 8 JOG B I Rotary encoder (S601) pulse input 9 VOL A I

10 VOL B I

11 to 14 KEY 0 to KEY 3 I Key input

15 GRADATION L O LED gradation signal (left) 16 S LOW (F01) O Sptctrum analyzer input (Super low flegency) (40Hz) 17 BPF 1 (F02) O Sptctrum analyzer input (100Hz) 18 BPF 2 O Sptctrum analyzer input (400Hz) 19 BPF 3 O Sptctrum analyzer input (2KHz) 20 BPF 4 O Sptctrum analyzer input (6KHz) 21 ALL B (L+R) I Sptctrum analyzer input (all band) 22 GLADATION O LED gradation signal (right)/WAKE UP signal

23 VSS I/O – Ground 24 VASS – Ground 25 VAref I Analog reference voltage input 26 VDD I/O – Power supply (+5V)

27 to 40 G 18 to G 5 O FL gride signal output

41 VDD VFT – Power supply (+5V) 42 to 45 G 4 to G 1 O FL gride signal output 46 to 67 S 1 to S 22 O FL segment signal output

68 VKK – Power supply (-30V)

69 VDD for CPU – Power supply (+5V)

70 X IN I X’tal (12.5MHz)

71 VSS for CPU – Ground

72 X OUT O X’tal (12.5MHz)

73 RESET I Reset signal input from main controller

74 CH for PAD O Channel signal output for PAD

75 BUSY for PAD O Busy signal output for PAD

76 TEST I Connected ground

77 – – Not used (to ground)

78 IIC DATA O Data output for IC501

79 IIC CLK O Clock output for IC501

80 – – Not used (to ground)

Pin Name I/O Function

Rotary encoder (S602) pulse input

R/WAKE UP

– 72 –

Page 47

SECTION 8

EXPLODED VIEWS

NOTE:

• Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.

• The mechanical parts with no reference number in the exploded views are not supplied.

• Hardware (# mark) list and accessories and packing materials are given in the last of this parts list.

• Color Indication of Appearance Parts Example: KNOB, BALANCE (WHITE)

Cabinets color

8-1. CASE SECTION

• Abbreviation G : German model EA3 : Saudi Arabia model EA4 : Israel model MX : Mexican model E2 : Without SW tuner model E3 : With SW tuner model SP : Singapore model TW : Taiwan model AUS : Australian model AR : Argentine model TH : Thailand model

The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.

CDM38LH-5BD32L

Front panel

Ref. No. Part No. Description Remark * 1 4-996-716-01 HOLDER (CDM)

2 3-363-099-41 SCREW (CASE 3 TP2)(GRAY) 2 3-363-099-71 SCREW (CASE 3 TP2)(SILVER) 3 3-363-099-01 SCREW (CASE 3 TP2)(GRAY) 3 3-363-099-11 SCREW (CASE 3 TP2)(SILVER)

* 4 4-214-452-01 CASE (SILVER) * 4 4-215-753-01 CASE (GRAY)

5 1-233-545-11 TUNER UNIT (EA4,TH) 5 1-233-545-14 ENCAPSULATED COMPONENT (E2,AR,MX,AUS)

not supplied

Ref. No. Part No. Description Remark

5 1-233-546-13 ENCAPSULATED COMPONENT (E3,EA3,SP,TW)

5 1-693-443-11 TUNER UNIT (AEP,UK,G,CIS) 6 4-951-620-01 SCREW (2.6x8), +BVTP 7 X-4950-953-1 PANEL ASSY, LOADING (RXD8S) 7 X-4950-978-1 PANEL ASSY, LOADING (GRX80)(SILVER) 7 X-4950-979-1 PANEL ASSY, LOADING (GRX80)(GRAY)

7 X-4950-981-1 PANEL ASSY, LOADING (RXD8)

Including Panel board (Ref No. 118)

– 73 –

Page 48

8-2. CHASSIS SECTION

)

not supplied

T951

not supplied

(RXD8/RXD8S)

not supplied

T11

not supplied

M901

#2 (RXD8/RXD8S)

#2 #2

(EA3,SP,MY)

(AUS)

(E2,E3,MX,TH)

(UK)

(AEP,UK,G,CIS,SP,MY,HK,TW,EA3,EA4

(AR)

(E3)

The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

51 4-965-822-01 FOOT

* 52 1-672-474-11 TRANS BOARD * 53 A-4417-639-A MAIN BOARD, COMPLETE (RXD8/RXD8S) * 53 A-4417-648-A MAIN BOARD, COMPLETE (GRX80:EA3) * 53 A-4417-652-A MAIN BOARD, COMPLETE (GRX80:E3,SP,TW)

* 53 A-4417-668-A MAIN BOARD, COMPLETE (GRX80:E2,AR,MX) * 53 A-4417-671-A MAIN BOARD, COMPLETE (GRX80:AUS) * 53 A-4417-676-A MAIN BOARD, COMPLETE (GRX80:EA4,TH)

54 1-783-570-11 WIRE (FLAT TYPE)(19 CORE) 55 1-769-977-11 WIRE (FLAT TYPE)(13 CORE)

(GRX80:E2,E3,AR,MX,AUS,EA4,TH)

55 1-773-009-11 WIRE (FLAT TYPE)(15 CORE) (150mm)

(GRX80:EA3,SP,TW/RXD8/RXD8S)

56 1-773-024-11 WIRE (FLAT TYPE)(15 CORE) (320mm)

* 57 3-703-244-00 BUSHING (2104), CORD

(AEP,UK,G,CIS,EA3,SP,AR,TW,AUS) 57 3-703-571-11 BUSHING (S)(4516), CORD (E2,E3,MX,EA4,TH) 58 1-569-007-11 ADAPTOR, CONVERSION 2P (E3)

58 1-569-008-21 ADAPTOR, CONVERSION 2P (EA3,SP,TW) 58 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (UK)

! 59 1-575-651-11 CORD, POWER (AEP,UK,G,CIS,EA3,SP,TW) ! 59 1-575-653-11 CORD, POWER (E2,E3,MX,TH) ! 59 1-690-608-11 CORD, POWER (AUS)

! 59 1-783-721-11 CORD, POWER (EA4)

! 59 1-783-941-21 CORD, POWER (AR)

* 60 A-4417-646-A SUB TRANS BOARD, COMPLETE (RXD8/RXD8S) * 61 4-214-451-01 PANEL, BACK (GRX80:E2,AR)

(Malaysia PRODUCT)

* 61 4-214-451-11 PANEL, BACK (GRX80:EA3)

* 61 4-214-451-21 PANEL, BACK (GRX80:SP)

61 4-214-451-31 PANEL, BACK (GRX80:MX)(Indonesia PRODUCT)

* 61 4-214-451-41 PANEL, BACK (GRX80:MX)(Malaysia PRODUCT) * 61 4-214-451-51 PANEL, BACK (GRX80:AUS) * 61 4-214-451-61 PANEL, BACK (GRX80:TW)

* 61 4-214-451-71 PANEL, BACK (GRX80:E2) * 61 4-214-451-81 PANEL, BACK (GRX80:EA4,TH) * 61 4-214-451-91 PANEL, BACK (GRX80:E3) * 61 4-215-165-01 PANEL, BACK (RXD8)(Indonesia PRODUCT) * 61 4-215-165-21 PANEL, BACK (RXD8S)

* 61 4-215-165-31 PANEL, BACK (RXD8)(Malaysia PRODUCT) * 61 4-217-515-21 PANEL, BACK (GRX80:E3) * 61 4-217-515-31 PANEL, BACK (GRX80:EA3)

62 1-773-042-11 WIRE (FLAT TYPE)(17 CORE) M901 1-763-072-11 FAN, D.C.

! T11 1-433-591-11 TRANSFORMER, POWER (RXD8/RXD8S) ! T951 1-433-556-11 TRANSFORMER, POWER (GRX80) ! T951 1-433-557-11 TRANSFORMER, POWER (RXD8/RXD8S)

– 74 –

Page 49

8-3. FRONT PANEL SECTION

Ver 1.1 2001.06

101

106

113

108

Supplied with

S601

107

Supplied with

105

102

S602

103

104

112

111

105

114

110

109

119

not supplied

115

110

109

123

#11

121

118

120

FL601

117

116

109

TCM230AWR1 TCM230PWR1

not supplied

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

101 X-4950-697-1 HOLDER (L) ASSY, CASSETTE (SILVER) 101 X-4950-976-1 HOLDER (L) ASSY, CASSETTE (GRAY) 102 X-4950-698-1 HOLDER (R) ASSY, CASSETTE (SILVER) 102 X-4950-977-1 HOLDER (R) ASSY, CASSETTE (GRAY) 103 4-214-760-11 CATCHER (A), PUSH

104 4-214-761-11 CATCHER (B), PUSH 105 4-214-775-11 SPRING, PUSH CATCHER RETURN 106 4-214-383-11 KNOB (JOG)(SILVER) 106 4-214-383-51 KNOB (JOG)(GRAY) 107 4-214-384-11 KNOB (VOL)(SILVER)

107 4-214-384-51 KNOB (VOL)(GRAY) 1084-214-447-11SPRING, TENSION 109 4-951-620-01 SCREW (2.6X8), +BVTP 110 4-210-045-02 DAMPER 111 4-988-663-01 FOOT (FELT)

112 4-962-708-71 EMBLEM (4-A), SONY 113 X-4950-696-1 PANEL ASSY, FRONT

(GRX80:E2,SP,AR,TW,MX,AUS,EA4,TH)(SILVER)

113 X-4950-701-1 PANEL ASSY, FRONT (GRX80:EA3)(GRAY) 113 X-4950-706-1 PANEL ASSY, FRONT (RXD8/RXD8S) 113 X-4950-980-1 PANEL ASSY, FRONT (GRX80:E3)(GRAY)

* 114 A-4417-663-A CD SW BOARD, COMPLETE

115 4-214-385-11 KNOB (MIC)(SILVER) 115 4-214-385-51 KNOB (MIC)(GRAY) 116 1-773-223-11 WIRE (FLAT TYPE)(25 CORE)

* 117 4-214-439-11 HOLDER, FL TUBE

* 118 A-4417-643-A PANEL BOARD, COMPLETE (RXD8/RXD8S) * 118 A-4417-650-A PANEL BOARD, COMPLETE (GRX80:EA3) * 118 A-4417-660-A PANEL BOARD, COMPLETE

* 119 4-214-736-11 HOLDER (L)(LED) * 120 4-214-737-11 HOLDER (R)(LED)

* 121 4-214-738-11 INDICATOR (ILLUMINATION 1)

122 4-951-620-01 SCREW (2.6X8), +BVTP

123 4-214-446-11 SPRING, TENTION

FL601 1-517-831-11 INDICATOR TUBE, FLUORESCENT

#11

(EXCEPT GRX80:EA3/RXD8/RXD8S)

– 75 –

Page 50

8-4. CD MECHANISM DECK SECTION-1 (CDM38LH-5BD32L)

201

202

211

203

201

205

204

209

M701

212

206

207

208

210

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

201 4-981-789-01 BRACKET, YOKE 202 4-977-945-01 TRAY (TURN) 203 X-4946-665-1 SHAFT ASSY, WORM 204 4-977-943-01 BELT (TURN) (1.2) 205 4-977-956-01 WHEEL, WORM

* 206 1-658-577-11 MOTOR (TURN) BOARD

207 4-988-162-01 ROLLER 208 4-977-941-01 BEARING (WORM)

* 209 1-658-576-11 SENSOR BOARD

210 4-934-376-01 SHAFT (ROLLER)

211 4-981-187-01 COLLAR (WORM) 212 4-977-944-01 TRAY (SLIDE) M701 A-4672-004-A MOTOR ASSY

– 76 –

Page 51

8-5. CD MECHANISM DECK SECTION-2 (CDM38LH-5BD32L)

251

267

268

266

261

259

258

254

269

251

261

256

253

270

251

271

257

252

255

not supplied

260

not supplied

M801

BU-5BD32L

S811

262

263

264

265

251

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

251 4-917-583-71 BRACKET, YOKE 252 4-977-954-01 PULLEY (SL) 253 4-977-953-01 GEAR (SL-A) 254 4-977-955-01 GEAR (SL-B) 255 4-977-942-01 BELT (SL) (1.4)

256 X-4946-667-1 CAM ASSY, BU 257 1-452-925-21 MAGNET ASSY 258 1-776-042-11 WIRE (FLAT TYPE) (8 CORE)

* 259 1-658-575-11 CONNECTOR BOARD

260 4-900-743-01 SPRING, COMPRESSION

261 4-985-672-01 SCREW (+PTPWHM2.6), FLOATING

* 262 1-658-578-11 MOTOR (SLIDE) BOARD

263 4-982-447-01 SPRING (BU), COMPRESSION 264 4-951-620-41 SCREW (2.6), +BVTP 265 X-4949-570-1 HOLDER (BU) ASSY

266 4-989-494-01 SCREW (SLIDER), STEP 267 4-989-492-11 SLIDER (38) 268 4-989-819-02 SPRING, TENSION 269 4-989-491-01 COVER, LENS 270 4-993-142-21 PULLEY (L), PRESS

* 271 4-900-718-01 BRACKET (ADJUSTMENT)

S811 1-473-335-11 ENCODER, ROTARY M801 A-4672-004-A MOTOR ASSY (SLIDE)

– 77 –

Page 52

8-6. BASE UNIT SECTION (BU-5BD32L)

301

302

309

303

305

M101

M102

304

306

307

308

The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

! 301 8-820-020-02 OPTICAL PICK-UP KSS-213D/Q-NP

302 1-769-069-11 WIRE (FLAT TYPE) (16 CORE) 303 4-917-567-01 GEAR (M) 304 4-951-940-01 INSULATOR (BU) 305 4-917-565-01 SHAFT, SLED

306 4-917-564-01 GEAR (P), FLATNESS

* 307 A-4724-486-A BD BOARD, COMPLETE

308 4-951-620-01 SCREW (2.6X8), +BVTP 309 3-713-786-51 SCREW +P 2X3 M101 X-4917-523-3 MOTOR ASSY (SPINDLE)

– 78 –

M102 X-4917-504-1 MOTOR ASSY (SLED)

Page 53

8-7. TC MECHANISM SECTION-1 (TCM230AWR1/230PWR1)

*NOTE: Two types of parts which are not interchangeable are available

for the Head deck (A) ASSY and Head deck (B) ASSY. When replacing the parts, refer to the following figure, and use the appropriate part.

408

Parts with “P” mark: 230PWR2

Parts without “P” mark: 230AWR2

412

413

407

406

404

HP101

403

HRPE101

403

405

404

407

405

408

406

410

411

409

402

401

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

401 3-376-464-11 SCREW(+PTT 2.6X6),GROUND POINT 402 3-911-116-21 RIVET, PUSH 403 3-016-574-11 SPRING (HEAD), TENSION 404 X-3374-156-4 PINCH LEVER (REV) ASSY 405 X-3374-155-4 PINCH LEVER (FWD) ASSY

406 3-016-564-01 BASE (PINCH LEVER FWD) 407 3-016-565-01 BASE (PINCH LEVER REV) 408 3-026-892-01 SPRING (CASSETTE), LEAF

* 409 A-2007-731-A AUDIO BOARD, COMPLETE

410 3-016-573-01 LEVER (EJECT PREVENTION R)

411 3-032-810-02 SPRING (R), TORSION 412 3-016-572-01 LEVER (EJECT PREVENTION L) 413 3-032-809-02 SPRING (L), TORSION HP101 A-2056-681-A DECK (A) ASSY, HEAD (230AWR2)(*NOTE) HP101 A-2056-681-B DECK (A) ASSY, HEAD (230PWR2)(*NOTE)

HRPE101 A-2056-682-A DECK (B) ASSY, HEAD (230AWR2)(*NOTE) HRPE101 A-2056-682-B DECK (B) ASSY, HEAD (230PWR2)(*NOTE)

– 79 –

Page 54

8-8. TC MECHANISM SECTION-2 (TCM230AWR1/230PWR1)

455

461

458

465

459

*NOTE: Two types of parts which are not interchangeable are available

for the mechanical block assembly. When replacing the parts, refer to the following figure, and use the appropriate part.

Parts with “P” mark: 230PWR2

Parts without “P” mark: 230AWR2

451

462

460

#10

463

465

460

452

454

456

465

459

464

458

455

452

456

457

453

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * 451 X-3374-214-3 CHASSIS ASSY, MAIN

452 3-016-570-01 BELT (CAPSTAN) 453 3-016-569-01 BELT (TENSION) 454 3-017-360-01 BRACKET (MOTOR) 455 X-3376-497-1 FLYWHEEL (FWD) ASSY

456 X-3374-235-1 FLYWHEEL (REV) ASSY 457 X-3374-238-1 PULLEY ASSY, TENSION 458 3-024-405-01 BELT (FR2) 459 A-2004-629-A MECHANICAL BLOCK ASSY (230AWR2)(*NOTE)

459 A-2004-629-B MECHANICAL BLOCK ASSY (230PWR2)(*NOTE)

460 3-016-566-01 SLIDER, REVERSE

* 461 A-2007-732-A LEAF SW BOARD, COMPLETE

462 3-016-575-11 SPRING, TORSION 463 3-019-208-01 WASHER, STOPPER 464 3-027-453-01 SPRING (GROUND), TENSION

465 3-030-823-01 SCREW (+BVTT) (2X3.5) M1 A-2004-628-A MOTOR ASSY, CAPSTAN

– 80 –

Page 55

SECTION 9

ELECTRICAL PARTS LIST

Note:

The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.

When indicating parts by reference number, please include the board name.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

* A-2007-731-A AUDIO BOARD, COMPLETE

*********************

< CAPACITOR >

C301 1-162-289-31 CERAMIC 390PF 10% 50V C302 1-126-968-11 ELECT 100uF 20% 6.3V C303 1-162-282-31 CERAMIC 100PF 10% 50V C304 1-130-483-00 MYLAR 0.01uF 5% 50V C305 1-107-715-11 ELECT 22uF 20% 16V

C311 1-162-289-31 CERAMIC 390PF 10% 50V C313 1-162-282-31 CERAMIC 100PF 10% 50V C314 1-130-487-00 MYLAR 0.022uF 5% 50V C315 1-126-233-11 ELECT 22uF 20% 50V C331 1-137-427-11 FILM 120PF 5% 50V

C332 1-162-288-31 CERAMIC 330PF 10% 50V C333 1-162-209-31 CERAMIC 27PF 5% 50V C401 1-162-289-31 CERAMIC 390PF 10% 50V C402 1-126-968-11 ELECT 100uF 20% 6.3V C403 1-162-282-31 CERAMIC 100PF 10% 50V

C404 1-130-483-00 MYLAR 0.01uF 5% 50V C405 1-107-715-11 ELECT 22uF 20% 16V C411 1-162-289-31 CERAMIC 390PF 10% 50V C413 1-162-282-31 CERAMIC 100PF 10% 50V C414 1-130-487-00 MYLAR 0.022uF 5% 50V

C415 1-126-233-11 ELECT 22uF 20% 50V C431 1-137-427-11 FILM 120PF 5% 50V C432 1-162-288-31 CERAMIC 330PF 10% 50V C433 1-162-209-31 CERAMIC 27PF 5% 50V C601 1-104-396-11 ELECT 10uF 20% 16V

C602 1-104-396-11 ELECT 10uF 20% 16V C611 1-104-396-11 ELECT 10uF 20% 16V C612 1-104-396-11 ELECT 10uF 20% 16V C621 1-137-150-11 FILM 0.01uF 5% 100V C622 1-126-961-11 ELECT 2.2uF 20% 50V

C623 1-136-155-00 FILM 0.015uF 5% 50V C624 1-130-481-00 MYLAR 0.0068uF 5% 50V C625 1-130-481-00 MYLAR 0.0068uF 5% 50V C627 1-124-903-11 ELECT 1uF 20% 50V C628 1-136-153-00 FILM 0.01uF 5% 50V

C642 1-104-664-11 ELECT 47uF 20% 16V

< CONNECTOR >

• Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set.

• -XX, -X mean standardized parts, so they may have some difference from the original one.

• Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.

• RESISTORS All resistors are in ohms METAL: Metal-film resistor METAL OXIDE: Metal Oxide-film resistor F : nonflammable

• SEMICONDUCTORS In each case, u: µ , for example: uA...: µ A..., uPA...: µPA..., uPB...: µ PB..., uPC...: µ PC..., uPD...: µ PD...

IC601 8-759-111-44 IC UPC4570C-1 IC602 8-759-143-54 IC UPC1330HA IC611 8-759-111-44 IC UPC4570C-1

L331 1-410-780-11 INDUCTOR 27mH L431 1-410-780-11 INDUCTOR 27mH L601 1-414-193-41 INDUCTOR 220uH L602 1-414-193-41 INDUCTOR 220uH

Q621 8-729-142-46 TRANSISTOR 2SC2001-LK Q622 8-729-142-46 TRANSISTOR 2SC2001-LK Q623 8-729-801-93 TRANSISTOR 2SD1387

R301 1-247-881-00 CARBON 120K 5% 1/4W R302 1-249-409-11 CARBON 220 5% 1/4W F R303 1-249-433-11 CARBON 22K 5% 1/4W R304 1-247-889-00 CARBON 270K 5% 1/4W R305 1-247-858-11 CARBON 13K 5% 1/4W

R311 1-247-881-00 CARBON 120K 5% 1/4W R312 1-247-807-31 CARBON 100 5% 1/4W R314 1-247-882-11 CARBON 130K 5% 1/4W R315 1-247-850-11 CARBON 6.2K 5% 1/4W R331 1-249-430-11 CARBON 12K 5% 1/4W

R401 1-247-881-00 CARBON 120K 5% 1/4W R402 1-249-409-11 CARBON 220 5% 1/4W F R403 1-249-433-11 CARBON 22K 5% 1/4W R404 1-247-889-00 CARBON 270K 5% 1/4W R405 1-247-858-11 CARBON 13K 5% 1/4W

R411 1-247-881-00 CARBON 120K 5% 1/4W R412 1-247-807-31 CARBON 100 5% 1/4W R414 1-247-882-11 CARBON 130K 5% 1/4W R415 1-247-850-11 CARBON 6.2K 5% 1/4W R431 1-249-430-11 CARBON 12K 5% 1/4W

R601 1-249-409-11 CARBON 220 5% 1/4W F R602 1-249-409-11 CARBON 220 5% 1/4W F R608 1-249-409-11 CARBON 220 5% 1/4W F R609 1-249-433-11 CARBON 22K 5% 1/4W R611 1-249-409-11 CARBON 220 5% 1/4W F

• CAPACITORS uF : µ F

• COILS uH : µ H

• Abbreviation G : German model EA3 : Saudi Arabia model MX : Mexican model EA4 : Israel model E2 : Without SW tuner model E3 : With SW tuner model SP : Singapore model TW : Taiwan model AUS : Australian model AR : Argentine model TH : Thailand model

< IC >

< COIL >

< TRANSISTOR >

< RESISTOR >

AUDIO

CN601 1-695-338-11 PIN, CONNECTOR (PC BOARD) 15P

R612 1-249-409-11 CARBON 220 5% 1/4W F

! R621 1-212-851-00 FUSIBLE 5.6 5% 1/4W F

– 81 –

Page 56

AUDIO

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

! R622 1-212-851-00 FUSIBLE 5.6 5% 1/4W F

R623 1-249-432-11 CARBON 18K 5% 1/4W R624 1-249-432-11 CARBON 18K 5% 1/4W

R625 1-249-429-11 CARBON 10K 5% 1/4W

C157 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V C159 1-163-019-00 CERAMIC CHIP 0.0068uF 10% 50V C161 1-126-206-11 ELECT CHIP 100uF 20% 6.3V C162 1-126-205-11 ELECT CHIP 47uF 20% 6.3V C163 1-126-206-11 ELECT CHIP 100uF 20% 6.3V

< VARIABLE RESISTOR >

RV301 1-238-598-11 RES, ADJ, CARBON 2.2K RV311 1-238-598-11 RES, ADJ, CARBON 2.2K RV341 1-241-768-11 RES, ADJ, CARBON 220K RV401 1-238-598-11 RES, ADJ, CARBON 2.2K RV411 1-238-598-11 RES, ADJ, CARBON 2.2K

RV441 1-241-768-11 RES, ADJ, CARBON 220K

< TRANSFORMER >

T621 1-423-980-11 TRANSFORMER, BIAS OSCILLATION

**************************************************************

* A-4724-486-A BD BOARD, COMPLETE

******************

< CAPACITOR >

C101 1-163-005-11 CERAMIC CHIP 470PF 10% 50V C102 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V C103 1-163-005-11 CERAMIC CHIP 470PF 10% 50V C104 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V C108 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V

C109 1-163-011-11 CERAMIC CHIP 0.0015uF 10% 50V C110 1-164-182-11 CERAMIC CHIP 0.0033uF 10% 50V C111 1-163-251-11 CERAMIC CHIP 100PF 5% 50V C112 1-163-038-91 CERAMIC CHIP 0.1uF 25V C113 1-163-038-91 CERAMIC CHIP 0.1uF 25V

C114 1-163-038-91 CERAMIC CHIP 0.1uF 25V C115 1-126-607-11 ELECT CHIP 47uF 20% 4V C116 1-126-607-11 ELECT CHIP 47uF 20% 4V C117 1-126-209-11 ELECT CHIP 100uF 20% 4V C118 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V

C119 1-163-235-11 CERAMIC CHIP 22PF 5% 50V C121 1-163-038-91 CERAMIC CHIP 0.1uF 25V C122 1-126-206-11 ELECT CHIP 100uF 20% 6.3V C123 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V C124 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V

C125 1-163-038-91 CERAMIC CHIP 0.1uF 25V C126 1-163-038-91 CERAMIC CHIP 0.1uF 25V C127 1-128-065-11 ELECT CHIP 68uF 20% 10V C128 1-163-038-91 CERAMIC CHIP 0.1uF 25V C129 1-163-031-11 CERAMIC CHIP 0.01uF 50V

C130 1-164-346-11 CERAMIC CHIP 1uF 16V C131 1-124-779-00 ELECT CHIP 10uF 20% 16V C133 1-164-346-11 CERAMIC CHIP 1uF 16V C140 1-164-346-11 CERAMIC CHIP 1uF 16V C141 1-164-346-11 CERAMIC CHIP 1uF 16V

C143 1-163-038-91 CERAMIC CHIP 0.1uF 25V C151 1-163-235-11 CERAMIC CHIP 22PF 5% 50V C153 1-163-038-91 CERAMIC CHIP 0.1uF 25V C154 1-110-501-11 CERAMIC CHIP 0.33uF 10% 16V C156 1-163-235-11 CERAMIC CHIP 22PF 5% 50V

C165 1-163-038-91 CERAMIC CHIP 0.1uF 25V C167 1-163-235-11 CERAMIC CHIP 22PF 5% 50V C168 1-163-235-11 CERAMIC CHIP 22PF 5% 50V C171 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V C172 1-163-123-00 CERAMIC CHIP 180PF 5% 50V

C181 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V C182 1-163-123-00 CERAMIC CHIP 180PF 5% 50V

< CONNECTOR >

CN101 1-778-874-11 CONNECTOR,FFC(LIF(NON-ZIF))19P CN102 1-777-937-11 CONNECTOR, FFC/FPC 16P

< FERRITE BEAD >

FB101 1-500-445-21 FERRITE 0UH FB103 1-500-445-21 FERRITE 0UH

< IC >

IC101 8-752-386-85 IC CXD2587Q IC102 8-759-549-28 IC BA5974FP-E IC103 8-752-085-51 IC CXA2568M-T

< TRANSISTOR >

Q101 8-729-010-08 TRANSISTOR MSB710-R

< RESISTOR >

R101 1-216-077-00 METAL CHIP 15K 5% 1/10W R102 1-216-097-91 RES,CHIP 100K 5% 1/10W R103 1-216-077-00 METAL CHIP 15K 5% 1/10W R104 1-216-085-00 METAL CHIP 33K 5% 1/10W R105 1-216-073-00 METAL CHIP 10K 5% 1/10W

R106 1-216-049-91 RES,CHIP 1K 5% 1/10W R107 1-216-073-00 METAL CHIP 10K 5% 1/10W R108 1-216-061-00 METAL CHIP 3.3K 5% 1/10W R109 1-216-121-91 RES,CHIP 1M 5% 1/10W R110 1-216-025-91 RES,CHIP 100 5% 1/10W

R111 1-216-121-91 RES,CHIP 1M 5% 1/10W R113 1-216-121-91 RES,CHIP 1M 5% 1/10W R114 1-216-073-00 METAL CHIP 10K 5% 1/10W R116 1-216-001-00 METAL CHIP 10 5% 1/10W R117 1-216-049-91 RES,CHIP 1K 5% 1/10W

R119 1-216-041-00 METAL CHIP 470 5% 1/10W R123 1-216-073-00 METAL CHIP 10K 5% 1/10W R124 1-216-097-91 RES,CHIP 100K 5% 1/10W R131 1-216-033-00 METAL CHIP 220 5% 1/10W R143 1-216-103-00 METAL CHIP 180K 5% 1/10W

R144 1-216-103-00 METAL CHIP 180K 5% 1/10W R147 1-216-069-00 METAL CHIP 6.8K 5% 1/10W R148 1-216-001-00 METAL CHIP 10 5% 1/10W R149 1-216-001-00 METAL CHIP 10 5% 1/10W R158 1-216-111-00 METAL CHIP 390K 5% 1/10W

R159 1-216-101-00 METAL CHIP 150K 5% 1/10W

– 82 –

The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.

Page 57

BD LEAF SW

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

R161 1-216-308-00 METAL CHIP 4.7 5% 1/10W R162 1-216-101-00 METAL CHIP 150K 5% 1/10W R171 1-216-078-00 RES,CHIP 16K 5% 1/10W R172 1-216-073-00 METAL CHIP 10K 5% 1/10W

R173 1-216-077-00 METAL CHIP 15K 5% 1/10W R181 1-216-078-00 RES,CHIP 16K 5% 1/10W R182 1-216-073-00 METAL CHIP 10K 5% 1/10W R183 1-216-077-00 METAL CHIP 15K 5% 1/10W

< NETWORK >

CD SW CONNECTOR

S807 1-762-875-21 SWITCH, KEYBOARD (§)

**************************************************************

* 1-658-575-11 CONNECTOR BOARD

*****************

< CONNECTOR >

* CN701 1-568-946-11 PIN, CONNECTOR 8P

CN702 1-750-413-11 CONNECTOR, FFC/FPC 8P

RN101 1-233-576-11 RES, CHIP NETWORK 100 RN102 1-233-576-11 RES, CHIP NETWORK 100

< SWITCH >

S101 1-572-085-11 SWITCH, LEAF (LIMIT IN SW)

< VIBRATOR >

X101 1-767-408-21 VIBRATOR, CRYSTAL (16.9344MHz)

**************************************************************

* A-4417-663-A CD SW BOARD, COMPLETE

*********************

< DIODE >

D801 8-719-056-13 DIODE SML79423C-TP15

(DISC 1, DISC IN/PLAY)

D802 8-719-056-13 DIODE SML79423C-TP15

(DISC 2, DISC IN/PLAY)

D803 8-719-056-13 DIODE SML79423C-TP15

(DISC 3, DISC IN/PLAY)

D804 8-719-063-93 DIODE SLR325VC-N-T32

((STANDBY) POWER SAVE/DEMO)

< RESISTOR >

< TRANSISTOR >

Q701 8-729-900-80 TRANSISTOR DTC114ES

< RESISTOR >

R703 1-249-435-11 CARBON 33K 5% 1/4W R704 1-249-429-11 CARBON 10K 5% 1/4W R705 1-249-417-11 CARBON 1K 5% 1/4W F

**************************************************************

* A-2007-732-A LEAF SW BOARD, COMPLETE

************************

< CAPACITOR >

C1001 1-107-716-11 ELECT 33uF 20% 10V

< CONNECTOR >

CN1001 1-568-860-11 SOCKET, CONNECTOR 17P CN1001 1-784-459-11 CONNECTOR, FFC/FPC 17P

< DIODE >

D1001 8-719-911-19 DIODE 1SS119 D1002 8-719-911-19 DIODE 1SS119

R801 1-216-049-91 RES,CHIP 1K 5% 1/10W R802 1-216-051-00 METAL CHIP 1.2K 5% 1/10W R803 1-216-055-00 METAL CHIP 1.8K 5% 1/10W R804 1-216-059-00 METAL CHIP 2.7K 5% 1/10W R805 1-216-061-00 METAL CHIP 3.3K 5% 1/10W

R806 1-216-065-91 RES,CHIP 4.7K 5% 1/10W R807 1-216-069-00 METAL CHIP 6.8K 5% 1/10W R808 1-216-022-00 METAL CHIP 75 5% 1/10W R809 1-216-029-00 METAL CHIP 150 5% 1/10W R810 1-216-022-00 METAL CHIP 75 5% 1/10W

R811 1-216-029-00 METAL CHIP 150 5% 1/10W R812 1-216-022-00 METAL CHIP 75 5% 1/10W R813 1-216-029-00 METAL CHIP 150 5% 1/10W R814 1-216-043-91 RES,CHIP 560 5% 1/10W

< SWITCH >

S801 1-762-875-21 SWITCH, KEYBOARD (1/u) S802 1-762-875-21 SWITCH, KEYBOARD

((STANDBY) POWER SAVE/DEMO) S803 1-762-875-21 SWITCH, KEYBOARD (DISC 1) S804 1-762-875-21 SWITCH, KEYBOARD (DISC 2) S805 1-762-875-21 SWITCH, KEYBOARD (DISC 3)

S806 1-762-875-21 SWITCH, KEYBOARD (DISC SKIP/EX-CHANGE)

< HOLDER >

* DM1001 1-784-581-11 HOLDER, CABLE (2.5MM PITCH) 4P

< IC >

IC1001 8-749-014-38 IC PHOTO INTERRUPTER SG-264 IC1002 8-749-014-38 IC PHOTO INTERRUPTER SG-264

< TRANSISTOR >

Q1001 8-729-029-56 TRANSISTOR DTA144ESA

< RESISTOR >

R907 1-247-879-11 CARBON 100K 5% 1/4W R1001 1-249-409-11 CARBON 220 5% 1/4W F R1002 1-249-409-11 CARBON 220 5% 1/4W F R1003 1-249-414-11 CARBON 560 5% 1/4W F R1004 1-247-834-11 CARBON 1.3K 5% 1/4W

R1005 1-247-818-11 CARBON 300 5% 1/4W R1006 1-247-864-11 CARBON 24K 5% 1/4W R1007 1-247-856-00 CARBON 11K 5% 1/4W R1008 1-249-417-11 CARBON 1K 5% 1/4W F

– 83 –

Page 58

LEAF SW

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

RV1001 1-241-785-11 RES, ADJ, CARBON 10K RV1002 1-241-785-11 RES, ADJ, CARBON 10K

S1001 1-570-953-11 SWITCH, PUSH (1 KEY)(A PLAY) S1002 1-570-953-11 SWITCH, PUSH (1 KEY)(B PLAY) S1003 1-771-333-11 SWITCH, LEAF (A HALF) S1004 1-771-205-11 SWITCH, LEAF (A 120/70) S1005 1-771-205-11 SWITCH, LEAF (REC A)

S1006 1-771-333-11 SWITCH, LEAF (B HALF) S1008 1-771-205-11 SWITCH, LEAF (B 120/70) S1009 1-771-205-11 SWITCH, LEAF (REC B)

**************************************************************

* A-4417-639-A MAIN BOARD, COMPLETE (RXD8/RXD8S)

* A-4417-648-A MAIN BOARD, COMPLETE (GRX80:EA3)

* A-4417-652-A MAIN BOARD, COMPLETE (GRX80:E3,SP,TW)

* A-4417-668-A MAIN BOARD, COMPLETE (GRX80:E2,AR,MX)

* A-4417-671-A MAIN BOARD, COMPLETE (GRX80:AUS)

* A-4417-676-A MAIN BOARD, COMPLETE (GRX80:EA4,TH)

7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S

C101 1-162-286-31 CERAMIC 220PF 10% 50V

C102 1-162-286-31 CERAMIC 220PF 10% 50V

C103 1-162-286-31 CERAMIC 220PF 10% 50V

C104 1-164-159-11 CERAMIC 0.1uF 50V C111 1-137-195-11 FILM 0.56uF 5% 50V

C112 1-136-158-00 FILM 0.027uF 5% 50V C113 1-136-167-00 FILM 0.15uF 5% 50V C114 1-130-480-00 MYLAR 0.0056uF 5% 50V C115 1-136-159-00 FILM 0.033uF 5% 50V C116 1-130-473-00 MYLAR 0.0015uF 5% 50V

C117 1-136-153-00 FILM 0.01uF 5% 50V C118 1-162-288-31 CERAMIC 330PF 10% 50V C119 1-130-479-00 MYLAR 0.0047uF 5% 50V C120 1-130-477-00 MYLAR 0.0033uF 5% 50V C121 1-126-964-11 ELECT 10uF 20% 50V

C122 1-162-291-31 CERAMIC 560PF 10% 50V C123 1-136-169-00 FILM 0.22uF 5% 50V C124 1-136-169-00 FILM 0.22uF 5% 50V C125 1-126-964-11 ELECT 10uF 20% 50V C131 1-104-664-11 ELECT 47uF 20% 16V

MAIN

< VARIABLE RESISTOR >

< SWITCH >

********************

< CAPACITOR >

(RXD8/RXD8S)

C132 1-104-664-11 ELECT 47uF 20% 16V C135 1-126-964-11 ELECT 10uF 20% 50V C141 1-126-959-11 ELECT 0.47uF 20% 50V C151 1-162-286-31 CERAMIC 220PF 10% 50V

(RXD8/RXD8S)

C152 1-162-286-31 CERAMIC 220PF 10% 50V

(RXD8/RXD8S)

C153 1-162-286-31 CERAMIC 220PF 10% 50V

(RXD8/RXD8S) C161 1-137-195-11 FILM 0.56uF 5% 50V C162 1-136-158-00 FILM 0.027uF 5% 50V C163 1-136-167-00 FILM 0.15uF 5% 50V C164 1-130-480-00 MYLAR 0.0056uF 5% 50V

C165 1-136-159-00 FILM 0.033uF 5% 50V C166 1-130-473-00 MYLAR 0.0015uF 5% 50V C167 1-136-153-00 FILM 0.01uF 5% 50V C168 1-162-288-31 CERAMIC 330PF 10% 50V C169 1-130-479-00 MYLAR 0.0047uF 5% 50V

C170 1-130-477-00 MYLAR 0.0033uF 5% 50V C171 1-126-964-11 ELECT 10uF 20% 50V C172 1-162-291-31 CERAMIC 560PF 10% 50V C173 1-136-169-00 FILM 0.22uF 5% 50V C174 1-136-169-00 FILM 0.22uF 5% 50V

C175 1-126-964-11 ELECT 10uF 20% 50V C176 1-136-495-11 FILM 0.068uF 5% 50V C177 1-136-153-00 FILM 0.01uF 5% 50V C181 1-161-494-00 CERAMIC 0.022uF 25V C182 1-161-494-00 CERAMIC 0.022uF 25V

C183 1-126-964-11 ELECT 10uF 20% 50V C184 1-126-964-11 ELECT 10uF 20% 50V C193 1-126-964-11 ELECT 10uF 20% 50V

(GRX80) C197 1-164-159-11 CERAMIC 0.1uF 50V C301 1-126-960-11 ELECT 1uF 20% 50V

C302 1-130-479-00 MYLAR 0.0047uF 5% 50V C303 1-136-165-00 FILM 0.1uF 5% 50V C304 1-136-165-00 FILM 0.1uF 5% 50V C305 1-126-964-11 ELECT 10uF 20% 50V C306 1-126-960-11 ELECT 1uF 20% 50V

C307 1-126-959-11 ELECT 0.47uF 20% 50V C308 1-126-964-11 ELECT 10uF 20% 50V C309 1-137-194-81 FILM 0.47uF 5% 50V C310 1-162-290-31 CERAMIC 470PF 10% 50V C311 1-126-964-11 ELECT 10uF 20% 50V

C312 1-126-959-11 ELECT 0.47uF 20% 50V C313 1-162-294-31 CERAMIC 0.001uF 10% 50V C314 1-126-964-11 ELECT 10uF 20% 50V C315 1-126-963-11 ELECT 4.7uF 20% 50V C316 1-104-665-11 ELECT 100uF 20% 10V

C317 1-104-665-11 ELECT 100uF 20% 10V C320 1-162-290-31 CERAMIC 470PF 10% 50V C333 1-162-600-11 CERAMIC 0.0047uF 30% 16V C334 1-162-600-11 CERAMIC 0.0047uF 30% 16V C351 1-126-960-11 ELECT 1uF 20% 50V

C352 1-130-479-00 MYLAR 0.0047uF 5% 50V C353 1-136-165-00 FILM 0.1uF 5% 50V C354 1-136-165-00 FILM 0.1uF 5% 50V C355 1-126-964-11 ELECT 10uF 20% 50V

– 84 –

Page 59

MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

C356 1-126-960-11 ELECT 1uF 20% 50V

C357 1-126-959-11 ELECT 0.47uF 20% 50V C358 1-126-964-11 ELECT 10uF 20% 50V C359 1-137-194-81 FILM 0.47uF 5% 50V C382 1-104-665-11 ELECT 100uF 20% 10V C390 1-126-935-11 ELECT 470uF 20% 6.3V

C391 1-161-494-00 CERAMIC 0.022uF 25V C392 1-126-916-11 ELECT 1000uF 20% 6.3V C393 1-161-494-00 CERAMIC 0.022uF 25V C394 1-126-925-11 ELECT 470uF 20% 10V C396 1-126-961-11 ELECT 2.2uF 20% 50V

C397 1-126-961-11 ELECT 2.2uF 20% 50V C401 1-136-165-00 FILM 0.1uF 5% 50V

(RXD8/RXD8S)

C402 1-136-165-00 FILM 0.1uF 5% 50V

(RXD8/RXD8S)

C403 1-162-306-11 CERAMIC 0.01uF 20% 16V

(RXD8/RXD8S)

C404 1-162-306-11 CERAMIC 0.01uF 20% 16V

(RXD8/RXD8S)

C410 1-126-963-11 ELECT 4.7uF 20% 50V C411 1-162-306-11 CERAMIC 0.01uF 20% 16V C412 1-107-717-11 ELECT 47uF 20% 50V C432 1-104-665-11 ELECT 100uF 20% 10V C433 1-126-961-11 ELECT 2.2uF 20% 50V

C437 1-126-968-11 ELECT 100uF 20% 50V C451 1-136-165-00 FILM 0.1uF 5% 50V

(RXD8/RXD8S)

C452 1-136-165-00 FILM 0.1uF 5% 50V

(RXD8/RXD8S)

C453 1-162-306-11 CERAMIC 0.01uF 20% 16V

(RXD8/RXD8S)

C454 1-162-306-11 CERAMIC 0.01uF 20% 16V

(RXD8/RXD8S)

C501 1-126-964-11 ELECT 10uF 20% 50V C502 1-164-159-11 CERAMIC 0.1uF 50V C503 1-136-165-00 FILM 0.1uF 5% 50V C504 1-126-926-11 ELECT 1000uF 20% 10V C508 1-109-889-11 ELECT 1uF 20% 50V

C610 1-102-953-00 CERAMIC 18PF 5% 50V C611 1-102-951-00 CERAMIC 15PF 5% 50V C614 1-162-306-11 CERAMIC 0.01uF 20% 16V C616 1-104-665-11 ELECT 100uF 20% 10V C662 1-162-306-11 CERAMIC 0.01uF 20% 16V

C664 1-104-665-11 ELECT 100uF 20% 10V C698 1-162-306-11 CERAMIC 0.01uF 20% 16V C699 1-104-665-11 ELECT 100uF 20% 10V C801 1-126-963-11 ELECT 4.7uF 20% 50V C802 1-162-290-31 CERAMIC 470PF 10% 50V

C842 1-127-752-11 ELECT 3300uF 20% 63V

(RXD8/RXD8S)

C842 1-127-814-11 ELECT 3300uF 20% 80V

(GRX80)

C843 1-136-165-00 FILM 0.1uF 5% 50V

(GRX80) C844 1-130-777-00 FILM 0.1uF 10% 100V C851 1-126-963-11 ELECT 4.7uF 20% 50V C852 1-162-290-31 CERAMIC 470PF 10% 50V

C853 1-162-282-31 CERAMIC 100PF 10% 50V C854 1-104-665-11 ELECT 100uF 20% 10V C857 1-136-495-11 FILM 0.068uF 5% 50V C858 1-136-495-11 FILM 0.068uF 5% 50V C859 1-128-560-11 ELECT 22uF 20% 100V

C881 1-126-967-11 ELECT 47uF 20% 50V C891 1-127-811-11 ELECT 3300uF 20% 50V

(GRX80) C892 1-127-752-11 ELECT 3300uF 20% 63V

(RXD8/RXD8S)

C892 1-127-814-11 ELECT 3300uF 20% 80V

(GRX80) C893 1-136-165-00 FILM 0.1uF 5% 50V

(GRX80)

C894 1-130-777-00 FILM 0.1uF 10% 100V C901 1-136-165-00 FILM 0.1uF 5% 50V C902 1-126-936-11 ELECT 3300uF 20% 16V

(RXD8/RXD8S)

C902 1-126-937-11 ELECT 4700uF 20% 16V

(GRX80) C903 1-126-933-11 ELECT 100uF 20% 16V

C904 1-104-664-11 ELECT 47uF 20% 16V C905 1-104-665-11 ELECT 100uF 20% 10V C906 1-136-165-00 FILM 0.1uF 5% 50V C907 1-128-548-11 ELECT 4700uF 20% 25V C909 1-126-964-11 ELECT 10uF 20% 50V

C910 1-104-665-11 ELECT 100uF 20% 10V C911 1-126-964-11 ELECT 10uF 20% 50V C912 1-126-926-11 ELECT 1000uF 20% 10V C913 1-126-964-11 ELECT 10uF 20% 50V C914 1-126-767-11 ELECT 1000uF 20% 16V

C915 1-104-664-11 ELECT 47uF 20% 16V C916 1-162-306-11 CERAMIC 0.01uF 20% 16V C917 1-126-933-11 ELECT 100uF 20% 16V

(GRX80:E2,E3,EA3,SP,AR,TW,MX,AUS/RXD8/RXD8S) C951 1-136-165-00 FILM 0.1uF 5% 50V C952 1-126-768-11 ELECT 2200uF 20% 16V

C953 1-126-933-11 ELECT 100uF 20% 16V C955 1-104-665-11 ELECT 100uF 20% 10V C956 1-136-165-00 FILM 0.1uF 5% 50V

C803 1-162-282-31 CERAMIC 100PF 10% 50V C804 1-104-665-11 ELECT 100uF 20% 10V C807 1-136-495-11 FILM 0.068uF 5% 50V C808 1-136-495-11 FILM 0.068uF 5% 50V C809 1-128-560-11 ELECT 22uF 20% 100V

C810 1-128-578-11 ELECT 1uF 20% 100V C811 1-162-306-11 CERAMIC 0.01uF 20% 16V C812 1-162-306-11 CERAMIC 0.01uF 20% 16V C841 1-127-811-11 ELECT 3300uF 20% 50V

(GRX80)

< CONNECTOR >

CN303 1-784-776-11 CONNECTOR, FFC 15P CN304 1-784-778-11 CONNECTOR, FFC 17P

* CN371 1-568-832-11 SOCKET, CONNECTOR 13P

(GRX80:E2,AR,MX,AUS,EA4,TH)

CN371 1-568-834-11 SOCKET, CONNECTOR 15P

(GRX80:E3,EA3,SP,TW/RXD8/RXD8S)

* CN391 1-568-862-11 SOCKET, CONNECTOR 19P

– 85 –

Page 60

MAIN

Ref. No. Part No. Description Remark

CN392 1-785-334-11 PIN, CONNECTOR (LIGHT ANGLE)8P CN393 1-785-335-11 PIN, CONNECTOR (LIGHT ANGLE)9P

* CN403 1-564-518-11 PLUG, CONNECTOR 3P * CN501 1-568-841-11 SOCKET, CONNECTOR 25P

< DIODE >

D141 8-719-911-19 DIODE 1SS119-25 D191 8-719-911-19 DIODE 1SS119-25 D331 8-719-911-19 DIODE 1SS119-25 D333 8-719-911-19 DIODE 1SS119-25 D334 8-719-911-19 DIODE 1SS119-25

D335 8-719-911-19 DIODE 1SS119-25 D401 8-719-911-19 DIODE 1SS119-25 D403 8-719-911-19 DIODE 1SS119-25 D405 8-719-024-99 DIODE 11ES2-NTA2B D406 8-719-024-99 DIODE 11ES2-NTA2B

D407 8-719-024-99 DIODE 11ES2-NTA2B D411 8-719-911-19 DIODE 1SS119-25 D501 8-719-911-19 DIODE 1SS119-25 D502 8-719-911-19 DIODE 1SS119-25 D503 8-719-911-19 DIODE 1SS119-25

D504 8-719-911-19 DIODE 1SS119-25 D505 8-719-911-19 DIODE 1SS119-25 D506 8-719-911-19 DIODE 1SS119-25 D509 8-719-911-19 DIODE 1SS119-25 D607 8-719-911-19 DIODE 1SS119-25

Ref. No. Part No. Description Remark

< IC >

IC101 8-759-571-54 IC M62493FP IC181 8-759-634-51 IC M5218AP IC301 8-759-495-26 IC HA12215 IC381 8-749-923-04 IC TOTX178 (CD DIGITAL OUT OPTICAL) IC501 8-759-571-18 IC M30622MA-A01FP

IC502 8-759-635-63 IC M51943BSL IC801 8-749-015-37 IC STK411-240E (GRX80) IC801 8-749-015-46 IC STK407-100E (RXD8/RXD8S) IC901 8-759-604-86 IC M5F7807L IC902 8-759-231-53 IC TA7805S

IC903 8-759-088-08 IC UPC7812AHF

< JACK >

J101 1-774-411-11 JACK, PIN 6P (VIDEO/AUDIO IN, MD IN/OUT) J191 1-774-785-11 JACK, PIN 1P (GRX80)

< COIL >

L381 1-410-521-11 INDUCTOR 100uH L392 1-410-521-11 INDUCTOR 100uH L401 1-420-872-00 COIL, AIR-CORE (RXD8/RXD8S) L451 1-420-872-00 COIL, AIR-CORE (RXD8/RXD8S) L501 1-410-509-11 INDUCTOR 10uH

< TRANSISTOR >

D644 8-719-911-19 DIODE 1SS119-25 D801 8-719-911-19 DIODE 1SS119-25 D802 8-719-118-97 DIODE RD16F-T7B2 D803 8-719-911-19 DIODE 1SS119-25 D831 8-719-302-37 DIODE RBV-602

D832 8-719-060-53 DIODE RBV-2506 (GRX80) D851 8-719-911-19 DIODE 1SS119-25 D852 8-719-118-97 DIODE RD16F-T7B2 (GRX80) D881 8-719-911-19 DIODE 1SS119-25 D901 8-719-024-99 DIODE 11ES2-NTA2B

D902 8-719-024-99 DIODE 11ES2-NTA2B D903 8-719-024-99 DIODE 11ES2-NTA2B D904 8-719-024-99 DIODE 11ES2-NTA2B D905 8-719-933-36 DIODE HZS6B1L D906 8-719-911-19 DIODE 1SS119-25

D907 8-719-024-99 DIODE 11ES2-NTA2B D908 8-719-024-99 DIODE 11ES2-NTA2B D909 8-719-024-99 DIODE 11ES2-NTA2B D910 8-719-024-99 DIODE 11ES2-NTA2B D915 8-719-935-69 DIODE HZS11B1LTD

D921 8-719-911-19 DIODE 1SS119-25 (GRX80) D922 8-719-911-19 DIODE 1SS119-25 (GRX80) D923 8-719-911-19 DIODE 1SS119-25 (GRX80) D924 8-719-024-99 DIODE 11ES2-NTA2B (GRX80) D925 8-719-024-99 DIODE 11ES2-NTA2B (GRX80)

Q111 8-729-119-78 TRANSISTOR 2SC403SP-51 Q112 8-729-119-78 TRANSISTOR 2SC403SP-51 Q113 8-729-141-30 TRANSISTOR 2SC3623A-LK Q161 8-729-119-78 TRANSISTOR 2SC403SP-51 Q162 8-729-119-78 TRANSISTOR 2SC403SP-51

Q163 8-729-141-30 TRANSISTOR 2SC3623A-LK Q181 8-729-141-30 TRANSISTOR 2SC3623A-LK Q191 8-729-141-30 TRANSISTOR 2SC3623A-LK (GRX80) Q192 8-729-900-63 TRANSISTOR DTA124ES (GRX80) Q201 8-729-900-36 TRANSISTOR DTC124ES

Q251 8-729-900-36 TRANSISTOR DTC124ES Q331 8-729-118-00 TRANSISTOR 2SB1116-L Q332 8-729-900-80 TRANSISTOR DTC114ES Q333 8-729-118-00 TRANSISTOR 2SB1116-L Q334 8-729-900-80 TRANSISTOR DTC114ES

Q335 8-729-900-80 TRANSISTOR DTC114ES Q336 8-729-116-59 TRANSISTOR 2SB1068TP Q337 8-729-045-21 TRANSISTOR 2SD1513TP-LK Q338 8-729-422-57 TRANSISTOR UN4111 Q339 8-729-900-80 TRANSISTOR DTC114ES

Q340 8-729-116-59 TRANSISTOR 2SB1068TP Q341 8-729-045-21 TRANSISTOR 2SD1513TP-LK Q342 8-729-422-57 TRANSISTOR UN4111 Q343 8-729-900-80 TRANSISTOR DTC114ES Q401 8-729-119-77 TRANSISTOR 2SA1175-FEK

D971 8-719-200-82 DIODE 11ES2 (GRX80:EA4,TH)

< FERRITE BEAD >

FB391 1-412-473-21 INDUCTOR 0UH FB392 1-412-473-21 INDUCTOR 0UH

Q402 8-729-111-29 TRANSISTOR 2SD1616A-K Q411 8-729-141-30 TRANSISTOR 2SC3623A-LK Q412 8-729-900-63 TRANSISTOR DTA124ES Q431 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA Q432 8-729-140-82 TRANSISTOR 2SA988-PAFAEA

Q433 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA

– 86 –

Page 61

MAIN

Ref. No. Part No. Description Remark

Q434 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA Q435 8-729-900-36 TRANSISTOR DTC124ES Q436 8-729-119-77 TRANSISTOR 2SA1175-FEK Q437 8-729-119-79 TRANSISTOR 2SC2785-FEK

Q439 8-729-119-79 TRANSISTOR 2SC2785-FEK Q471 8-729-141-30 TRANSISTOR 2SC3623A-LK Q501 8-729-119-78 TRANSISTOR 2SC403SP-51 Q508 8-729-900-63 TRANSISTOR DTA124ES Q509 8-729-900-63 TRANSISTOR DTA124ES

Q801 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA Q803 8-729-140-82 TRANSISTOR 2SA988-PAFAEA Q804 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA Q831 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA Q832 8-729-119-79 TRANSISTOR 2SC2785-FEK

Q851 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA Q881 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA Q901 8-729-209-15 TRANSISTOR 2SD2012 Q902 8-729-119-78 TRANSISTOR 2SC403SP-51 Q903 8-729-900-36 TRANSISTOR DTC124ES

Q904 8-729-900-36 TRANSISTOR DTC124ES Q905 8-729-040-20 TRANSISTOR RT1P137L-TP Q907 8-729-040-20 TRANSISTOR RT1P137L-TP Q908 8-729-900-36 TRANSISTOR DTC124ES Q909 8-729-026-68 TRANSISTOR 2SD2525(TP)

Q913 8-729-119-78 TRANSISTOR 2SC403SP-51 Q914 8-729-119-77 TRANSISTOR 2SA1175-FEK Q923 8-729-900-36 TRANSISTOR DTC124ES Q951 8-729-141-83 TRANSISTOR 2SB1094-LK Q952 8-729-119-77 TRANSISTOR 2SA1175-FEK

< RESISTOR >

R101 1-249-417-11 CARBON 1K 5% 1/4W F R102 1-249-417-11 CARBON 1K 5% 1/4W F R103 1-249-417-11 CARBON 1K 5% 1/4W F R111 1-249-429-11 CARBON 10K 5% 1/4W R112 1-247-895-00 CARBON 470K 5% 1/4W

R113 1-247-894-11 CARBON 430K 5% 1/4W R114 1-249-415-11 CARBON 680 5% 1/4W F R115 1-249-433-11 CARBON 22K 5% 1/4W R116 1-247-887-00 CARBON 220K 5% 1/4W R117 1-249-429-11 CARBON 10K 5% 1/4W

R118 1-249-437-11 CARBON 47K 5% 1/4W R119 1-249-421-11 CARBON 2.2K 5% 1/4W F R120 1-249-441-11 CARBON 100K 5% 1/4W R121 1-249-429-11 CARBON 10K 5% 1/4W R124 1-249-421-11 CARBON 2.2K 5% 1/4W F

R125 1-247-843-11 CARBON 3.3K 5% 1/4W R126 1-249-421-11 CARBON 2.2K 5% 1/4W F R131 1-247-807-31 CARBON 100 5% 1/4W R132 1-247-807-31 CARBON 100 5% 1/4W R133 1-247-807-31 CARBON 100 5% 1/4W

R141 1-249-433-11 CARBON 22K 5% 1/4W R142 1-249-433-11 CARBON 22K 5% 1/4W R143 1-249-417-11 CARBON 1K 5% 1/4W F R144 1-249-441-11 CARBON 100K 5% 1/4W R145 1-247-903-00 CARBON 1M 5% 1/4W

R151 1-249-417-11 CARBON 1K 5% 1/4W F

Ref. No. Part No. Description Remark

R152 1-249-417-11 CARBON 1K 5% 1/4W F R153 1-249-417-11 CARBON 1K 5% 1/4W F R161 1-249-429-11 CARBON 10K 5% 1/4W R162 1-247-895-00 CARBON 470K 5% 1/4W

R163 1-247-894-11 CARBON 430K 5% 1/4W R164 1-249-415-11 CARBON 680 5% 1/4W F R165 1-249-433-11 CARBON 22K 5% 1/4W R166 1-247-887-00 CARBON 220K 5% 1/4W R167 1-249-429-11 CARBON 10K 5% 1/4W

R168 1-249-437-11 CARBON 47K 5% 1/4W R169 1-249-421-11 CARBON 2.2K 5% 1/4W F R170 1-249-441-11 CARBON 100K 5% 1/4W R171 1-249-429-11 CARBON 10K 5% 1/4W R178 1-249-421-11 CARBON 2.2K 5% 1/4W F

R181 1-249-429-11 CARBON 10K 5% 1/4W R182 1-249-417-11 CARBON 1K 5% 1/4W F R183 1-249-425-11 CARBON 4.7K 5% 1/4W F R184 1-249-429-11 CARBON 10K 5% 1/4W R185 1-249-441-11 CARBON 100K 5% 1/4W

R186 1-249-429-11 CARBON 10K 5% 1/4W R187 1-249-429-11 CARBON 10K 5% 1/4W R188 1-249-429-11 CARBON 10K 5% 1/4W R190 1-249-441-11 CARBON 100K 5% 1/4W

(GRX80)

R196 1-249-417-11 CARBON 1K 5% 1/4W F

(GRX80)

R197 1-249-441-11 CARBON 100K 5% 1/4W

(GRX80)

R198 1-249-417-11 CARBON 1K 5% 1/4W F

(GRX80)

R199 1-249-429-11 CARBON 10K 5% 1/4W

(GRX80) R201 1-247-888-11 CARBON 240K 5% 1/4W R202 1-247-903-00 CARBON 1M 5% 1/4W

R251 1-247-888-11 CARBON 240K 5% 1/4W R252 1-247-903-00 CARBON 1M 5% 1/4W R301 1-249-435-11 CARBON 33K 5% 1/4W R302 1-249-421-11 CARBON 2.2K 5% 1/4W F R303 1-247-807-31 CARBON 100 5% 1/4W

R304 1-247-807-31 CARBON 100 5% 1/4W R305 1-249-421-11 CARBON 2.2K 5% 1/4W F R306 1-249-428-11 CARBON 8.2K 5% 1/4W F R307 1-249-428-11 CARBON 8.2K 5% 1/4W F R308 1-249-425-11 CARBON 4.7K 5% 1/4W F

R309 1-249-433-11 CARBON 22K 5% 1/4W R311 1-247-903-00 CARBON 1M 5% 1/4W R312 1-247-884-11 CARBON 160K 5% 1/4W R313 1-249-441-11 CARBON 100K 5% 1/4W R315 1-249-429-11 CARBON 10K 5% 1/4W

R316 1-249-432-11 CARBON 18K 5% 1/4W R317 1-249-429-11 CARBON 10K 5% 1/4W R318 1-249-429-11 CARBON 10K 5% 1/4W R319 1-247-893-11 CARBON 390K 5% 1/4W R321 1-249-422-11 CARBON 2.7K 5% 1/4W F

R322 1-249-428-11 CARBON 8.2K 5% 1/4W F R324 1-247-876-11 CARBON 75K 5% 1/4W R325 1-247-876-11 CARBON 75K 5% 1/4W R326 1-249-437-11 CARBON 47K 5% 1/4W

– 87 –

Page 62

MAIN

Ref. No. Part No. Description Remark

R327 1-249-437-11 CARBON 47K 5% 1/4W

R328 1-249-437-11 CARBON 47K 5% 1/4W R329 1-249-417-11 CARBON 1K 5% 1/4W F R330 1-249-425-11 CARBON 4.7K 5% 1/4W F R331 1-249-425-11 CARBON 4.7K 5% 1/4W F R332 1-249-415-11 CARBON 680 5% 1/4W F

R333 1-249-421-11 CARBON 2.2K 5% 1/4W F R334 1-249-415-11 CARBON 680 5% 1/4W F R335 1-249-421-11 CARBON 2.2K 5% 1/4W F R336 1-249-437-11 CARBON 47K 5% 1/4W R337 1-249-417-11 CARBON 1K 5% 1/4W F

R338 1-249-411-11 CARBON 330 5% 1/4W R339 1-249-437-11 CARBON 47K 5% 1/4W R340 1-249-437-11 CARBON 47K 5% 1/4W R341 1-249-411-11 CARBON 330 5% 1/4W R342 1-249-437-11 CARBON 47K 5% 1/4W

R343 1-249-417-11 CARBON 1K 5% 1/4W F R351 1-249-435-11 CARBON 33K 5% 1/4W R352 1-249-421-11 CARBON 2.2K 5% 1/4W F R353 1-247-807-31 CARBON 100 5% 1/4W R354 1-247-807-31 CARBON 100 5% 1/4W

R355 1-249-421-11 CARBON 2.2K 5% 1/4W F R356 1-249-428-11 CARBON 8.2K 5% 1/4W F R357 1-249-428-11 CARBON 8.2K 5% 1/4W F R358 1-249-425-11 CARBON 4.7K 5% 1/4W F R359 1-249-435-11 CARBON 33K 5% 1/4W

R391 1-247-807-31 CARBON 100 5% 1/4W R392 1-247-807-31 CARBON 100 5% 1/4W R393 1-249-435-11 CARBON 33K 5% 1/4W R394 1-249-435-11 CARBON 33K 5% 1/4W R401 1-260-076-11 CARBON 10 5% 1/2W

(RXD8/RXD8S)

R402 1-260-076-11 CARBON 10 5% 1/2W

(RXD8/RXD8S) R406 1-249-437-11 CARBON 47K 5% 1/4W R407 1-249-437-11 CARBON 47K 5% 1/4W R408 1-249-425-11 CARBON 4.7K 5% 1/4W F R409 1-249-441-11 CARBON 100K 5% 1/4W

Ref. No. Part No. Description Remark

R434 1-249-433-11 CARBON 22K 5% 1/4W

R435 1-249-435-11 CARBON 33K 5% 1/4W R437 1-249-429-11 CARBON 10K 5% 1/4W R438 1-249-429-11 CARBON 10K 5% 1/4W R439 1-249-425-11 CARBON 4.7K 5% 1/4W F R440 1-249-429-11 CARBON 10K 5% 1/4W

R441 1-249-435-11 CARBON 33K 5% 1/4W R443 1-249-417-11 CARBON 1K 5% 1/4W F R451 1-260-076-11 CARBON 10 5% 1/2W

(RXD8/RXD8S)

R452 1-260-076-11 CARBON 10 5% 1/2W

(RXD8/RXD8S)

R471 1-260-089-11 CARBON 150 5% 1/2W

(RXD8/RXD8S)

R471 1-260-090-11 CARBON 180 5% 1/2W

(GRX80)

R472 1-260-089-11 CARBON 150 5% 1/2W

(RXD8/RXD8S)

R472 1-260-090-11 CARBON 180 5% 1/2W

(GRX80) R473 1-249-402-11 CARBON 56 5% 1/4W F R474 1-249-417-11 CARBON 1K 5% 1/4W F

R481 1-260-089-11 CARBON 150 5% 1/2W

(RXD8/RXD8S)

R481 1-260-090-11 CARBON 180 5% 1/2W

(GRX80) R482 1-260-089-11 CARBON 150 5% 1/2W

(RXD8/RXD8S)

R482 1-260-090-11 CARBON 180 5% 1/2W

(GRX80) R483 1-260-089-11 CARBON 150 5% 1/2W

(RXD8/RXD8S)

R483 1-260-090-11 CARBON 180 5% 1/2W

(GRX80) R484 1-260-089-11 CARBON 150 5% 1/2W

(RXD8/RXD8S)

R484 1-260-090-11 CARBON 180 5% 1/2W

(GRX80) R501 1-249-413-11 CARBON 470 5% 1/4W F R502 1-249-425-11 CARBON 4.7K 5% 1/4W F

R410 1-249-421-11 CARBON 2.2K 5% 1/4W F

! R411 1-215-893-11 METAL OXIDE 1.5K 5% 2W F

(RXD8/RXD8S)

! R411 1-216-482-11 METAL OXIDE 1.8K 5% 3W F

(GRX80) R413 1-249-402-11 CARBON 56 5% 1/4W F R414 1-249-417-11 CARBON 1K 5% 1/4W F

R415 1-249-429-11 CARBON 10K 5% 1/4W R416 1-249-437-11 CARBON 47K 5% 1/4W R417 1-249-417-11 CARBON 1K 5% 1/4W F R421 1-260-089-11 CARBON 150 5% 1/2W

(RXD8/RXD8S)

R421 1-260-090-11 CARBON 180 5% 1/2W

(GRX80)

R422 1-260-089-11 CARBON 150 5% 1/2W

(RXD8/RXD8S)

R422 1-260-090-11 CARBON 180 5% 1/2W

(GRX80) R431 1-249-438-11 CARBON 56K 5% 1/4W R432 1-249-437-11 CARBON 47K 5% 1/4W

– 88 –

R503 1-249-437-11 CARBON 47K 5% 1/4W R504 1-249-437-11 CARBON 47K 5% 1/4W R505 1-249-429-11 CARBON 10K 5% 1/4W R508 1-249-421-11 CARBON 2.2K 5% 1/4W F R509 1-249-441-11 CARBON 100K 5% 1/4W

R510 1-249-409-11 CARBON 220 5% 1/4W F R521 1-249-437-11 CARBON 47K 5% 1/4W R522 1-249-429-11 CARBON 10K 5% 1/4W R523 1-249-427-11 CARBON 6.8K 5% 1/4W F

(RXD8/RXD8S)

R523 1-249-431-11 CARBON 15K 5% 1/4W

(GRX80:AUS)

R523 1-249-433-11 CARBON 22K 5% 1/4W

(GRX80:E2,AR,MX)

R523 1-249-437-11 CARBON 47K 5% 1/4W

(GRX80:EA3,EA4,TH)

R524 1-247-843-11 CARBON 3.3K 5% 1/4W

(GRX80:EA4,TH)

R524 1-249-435-11 CARBON 33K 5% 1/4W

(GRX80:EA3)

The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.

Page 63

MAIN

Ref. No. Part No. Description Remark

R524 1-249-437-11 CARBON 47K 5% 1/4W

(GRX80:E2,AR,MX,AUS/RXD8/RXD8S)

R527 1-249-429-11 CARBON 10K 5% 1/4W R536 1-249-429-11 CARBON 10K 5% 1/4W R550 1-247-843-11 CARBON 3.3K 5% 1/4W R551 1-249-429-11 CARBON 10K 5% 1/4W R567 1-247-807-31 CARBON 100 5% 1/4W

R568 1-249-429-11 CARBON 10K 5% 1/4W R569 1-249-429-11 CARBON 10K 5% 1/4W R570 1-249-429-11 CARBON 10K 5% 1/4W R571 1-249-429-11 CARBON 10K 5% 1/4W R577 1-249-429-11 CARBON 10K 5% 1/4W

R610 1-247-891-00 CARBON 330K 5% 1/4W R617 1-249-429-11 CARBON 10K 5% 1/4W R618 1-247-807-31 CARBON 100 5% 1/4W R619 1-247-807-31 CARBON 100 5% 1/4W R620 1-247-807-31 CARBON 100 5% 1/4W

(GRX80:EA4,TH/RXD8/RXD8S)

R621 1-247-807-31 CARBON 100 5% 1/4W

(RXD8/RXD8S) R622 1-249-425-11 CARBON 4.7K 5% 1/4W F R626 1-247-807-31 CARBON 100 5% 1/4W R627 1-247-807-31 CARBON 100 5% 1/4W R629 1-247-807-31 CARBON 100 5% 1/4W

R630 1-247-807-31 CARBON 100 5% 1/4W R632 1-247-807-31 CARBON 100 5% 1/4W

(GRX80:E2,E3,EA3,SP,AR,TW,MX,AUS/RXD8/RXD8S) R633 1-247-807-31 CARBON 100 5% 1/4W R635 1-249-413-11 CARBON 470 5% 1/4W F R636 1-247-807-31 CARBON 100 5% 1/4W

R637 1-249-417-11 CARBON 1K 5% 1/4W F R639 1-247-807-31 CARBON 100 5% 1/4W R642 1-247-807-31 CARBON 100 5% 1/4W R643 1-247-807-31 CARBON 100 5% 1/4W R649 1-247-807-31 CARBON 100 5% 1/4W

R650 1-247-807-31 CARBON 100 5% 1/4W R651 1-247-807-31 CARBON 100 5% 1/4W R652 1-247-807-31 CARBON 100 5% 1/4W R653 1-247-807-31 CARBON 100 5% 1/4W R654 1-247-807-31 CARBON 100 5% 1/4W

R655 1-247-807-31 CARBON 100 5% 1/4W R656 1-247-807-31 CARBON 100 5% 1/4W R657 1-247-807-31 CARBON 100 5% 1/4W R658 1-249-417-11 CARBON 1K 5% 1/4W F R659 1-247-807-31 CARBON 100 5% 1/4W

R660 1-247-807-31 CARBON 100 5% 1/4W R661 1-247-807-31 CARBON 100 5% 1/4W R663 1-247-807-31 CARBON 100 5% 1/4W R665 1-247-807-31 CARBON 100 5% 1/4W R666 1-247-807-31 CARBON 100 5% 1/4W

R667 1-247-807-31 CARBON 100 5% 1/4W R668 1-247-807-31 CARBON 100 5% 1/4W R669 1-247-807-31 CARBON 100 5% 1/4W R670 1-247-807-31 CARBON 100 5% 1/4W R671 1-247-807-31 CARBON 100 5% 1/4W

R686 1-247-807-31 CARBON 100 5% 1/4W R687 1-247-807-31 CARBON 100 5% 1/4W

Ref. No. Part No. Description Remark

R688 1-247-807-31 CARBON 100 5% 1/4W R689 1-247-807-31 CARBON 100 5% 1/4W R690 1-247-807-31 CARBON 100 5% 1/4W

R691 1-247-807-31 CARBON 100 5% 1/4W R801 1-249-417-11 CARBON 1K 5% 1/4W F R802 1-249-438-11 CARBON 56K 5% 1/4W R803 1-249-413-11 CARBON 470 5% 1/4W F

(GRX80)

R803 1-249-414-11 CARBON 560 5% 1/4W F

(RXD8/RXD8S)

R804 1-249-438-11 CARBON 56K 5% 1/4W R805 1-249-417-11 CARBON 1K 5% 1/4W F R806 1-249-431-11 CARBON 15K 5% 1/4W R807 1-249-441-11 CARBON 100K 5% 1/4W

! R808 1-220-893-11 METAL 0.22 10% 5W

R809 1-260-076-11 CARBON 10 5% 1/2W R810 1-215-872-11 METAL OXIDE 3.3K 5% 1W F

(GRX80)

! R811 1-212-881-11 FUSIBLE 100 5% 1/4W F ! R812 1-202-972-61 FUSIBLE 1 5% 1/4W F

R813 1-249-435-11 CARBON 33K 5% 1/4W

R814 1-249-421-11 CARBON 2.2K 5% 1/4W F R815 1-249-433-11 CARBON 22K 5% 1/4W R816 1-249-429-11 CARBON 10K 5% 1/4W R817 1-249-421-11 CARBON 2.2K 5% 1/4W F R818 1-249-435-11 CARBON 33K 5% 1/4W

R819 1-249-439-11 CARBON 68K 5% 1/4W R831 1-249-441-11 CARBON 100K 5% 1/4W R832 1-249-441-11 CARBON 100K 5% 1/4W R833 1-249-441-11 CARBON 100K 5% 1/4W R842 1-249-441-11 CARBON 100K 5% 1/4W

R851 1-249-417-11 CARBON 1K 5% 1/4W F R852 1-249-438-11 CARBON 56K 5% 1/4W R853 1-249-413-11 CARBON 470 5% 1/4W F

(GRX80)

R853 1-249-414-11 CARBON 560 5% 1/4W F

(RXD8/RXD8S)

R854 1-249-438-11 CARBON 56K 5% 1/4W

R855 1-249-417-11 CARBON 1K 5% 1/4W F R856 1-249-431-11 CARBON 15K 5% 1/4W R857 1-249-441-11 CARBON 100K 5% 1/4W

! R858 1-220-893-11 METAL 0.22 10% 5W

R859 1-260-076-11 CARBON 10 5% 1/2W

R860 1-215-872-11 METAL OXIDE 3.3K 5% 1W F

(GRX80)

! R861 1-212-881-11 FUSIBLE 100 5% 1/4W F

R881 1-249-435-11 CARBON 33K 5% 1/4W R882 1-249-435-11 CARBON 33K 5% 1/4W R892 1-249-441-11 CARBON 100K 5% 1/4W

R901 1-247-843-11 CARBON 3.3K 5% 1/4W R902 1-249-415-11 CARBON 680 5% 1/4W F R903 1-249-419-11 CARBON 1.5K 5% 1/4W F R904 1-249-414-11 CARBON 560 5% 1/4W F R905 1-249-425-11 CARBON 4.7K 5% 1/4W F

R906 1-247-843-11 CARBON 3.3K 5% 1/4W R907 1-249-415-11 CARBON 680 5% 1/4W F R908 1-249-429-11 CARBON 10K 5% 1/4W R909 1-249-430-11 CARBON 12K 5% 1/4W

– 89 –

The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.

Page 64

MAIN

MOTOR (SLIDE) MOTOR (TURN)

PANEL

Ref. No. Part No. Description Remark

R911 1-249-409-11 CARBON 220 5% 1/4W F

R920 1-249-383-11 CARBON 1.5 5% 1/6W F R921 1-249-383-11 CARBON 1.5 5% 1/6W F R931 1-249-429-11 CARBON 10K 5% 1/4W

< VARIABLE RESISTOR >

RV301 1-238-600-11 RES, ADJ, CARBON 10K RV351 1-238-600-11 RES, ADJ, CARBON 10K

< RELAY >

RY401 1-515-920-11 RELAY (GRX80:EA4,TH) RY401 1-755-168-11 RELAY

(GRX80:E2,E3,EA3,SP,AR,TW,MX,AUS/RXD8/RXD8S)

< THERMISTOR >

TH801 1-807-796-11 THERMISTOR

< TERMINAL >

TM401 1-537-240-31 TERMINAL BOARD (CHECKER PIN)(SPEAKER)

(GRX80)

TM401 1-694-302-11 TERMINAL BOARD (CHECKER PIN)

(RXD8/RXD8S)

TM402 1-537-240-31 TERMINAL BOARD (CHECKER PIN)

(SURROUND SPEAKER)

Ref. No. Part No. Description Remark

* 1-658-577-11 MOTOR (TURN) BOARD

******************

< CAPACITOR >

C701 1-162-306-11 CERAMIC 0.01uF 20% 16V C702 1-126-964-11 ELECT 10uF 20% 50V C705 1-162-306-11 CERAMIC 0.01uF 20% 16V

< CONNECTOR >

CN703 1-750-413-11 CONNECTOR, FFC/FPC 8P CN704 1-506-469-11 PIN, CONNECTOR 4P

< DIODE >

D701 8-719-983-66 DIODE MTZJ-T-72-3.6B (Malaysia PRODUCT) D701 8-719-109-69 DIODE RD3.6ES-B2 (Indonesia PRODUCT)

< IC >

IC701 8-759-633-65 IC M54641L

< RESISTOR >

R706 1-249-411-11 CARBON 330 5% 1/4W R707 1-249-401-11 CARBON 47 5% 1/4W F

**************************************************************

< VIBRATOR >

X601 1-567-098-41 VIBRATOR, CRYSTAL (32.768kHz) X613 1-781-107-21 VIBRATOR, SERAMIC (16MHz)

**************************************************************

* 1-658-578-11 MOTOR (SLIDE) BOARD

*******************

< CAPACITOR >

C801 1-162-306-11 CERAMIC 0.01uF 20% 16V C804 1-162-306-11 CERAMIC 0.01uF 20% 16V C805 1-126-964-11 ELECT 10uF 20% 50V

< CONNECTOR >

* CN801 1-568-947-11 PIN, CONNECTOR 9P

< DIODE >

D801 8-719-921-48 DIODE MTZJ-T-72-5.6C (Malaysia PRODUCT) D801 8-719-109-89 DIODE RD5.6ESB2 (Indonesia PRODUCT) D804 8-719-911-19 DIODE 1SS119 D805 8-719-911-19 DIODE 1SS119

< IC >

IC801 8-759-274-09 IC BA6286N

< RESISTOR >

R801 1-249-401-11 CARBON 47 5% 1/4W F

< SWITCH >

S801 1-762-527-11 SWITCH, ROTARY (OPEN/CLOSE)

* A-4417-643-A PANEL BOARD, COMPLETE (RXD8/RXD8S)

*********************

* A-4417-650-A PANEL BOARD, COMPLETE (GRX80:EA3)

*********************

* A-4417-660-A PANEL BOARD, COMPLETE

*********************

(EXCEPT GRX80:EA3/RXD8/RXD8S)

* 4-214-439-11 HOLDER, FL TUBE

< CAPACITOR >

C601 1-124-589-11 ELECT 47uF 20% 16V C602 1-126-163-11 ELECT 4.7uF 20% 50V C603 1-163-031-11 CERAMIC CHIP 0.01uF 50V C604 1-163-038-91 CERAMIC CHIP 0.1uF 25V C605 1-165-319-11 CERAMIC CHIP 0.1uF 50V

C608 1-165-319-11 CERAMIC CHIP 0.1uF 50V C610 1-124-589-11 ELECT 47uF 20% 16V C611 1-163-031-11 CERAMIC CHIP 0.01uF 50V C612 1-163-031-11 CERAMIC CHIP 0.01uF 50V C614 1-163-031-11 CERAMIC CHIP 0.01uF 50V

C615 1-163-031-11 CERAMIC CHIP 0.01uF 50V C616 1-126-157-11 ELECT 10uF 20% 16V C617 1-164-182-11 CERAMIC CHIP 0.0033uF 10% 50V C618 1-126-157-11 ELECT 10uF 20% 16V C619 1-126-157-11 ELECT 10uF 20% 16V

C620 1-126-163-11 ELECT 4.7uF 20% 50V C621 1-163-001-11 CERAMIC CHIP 220PF 10% 50V C622 1-163-001-11 CERAMIC CHIP 220PF 10% 50V C625 1-126-157-11 ELECT 10uF 20% 16V C628 1-126-163-11 ELECT 4.7uF 20% 50V

**************************************************************

– 90 –

Page 65

PANEL

Ref. No. Part No. Description Remark

C629 1-124-589-11 ELECT 47uF 20% 16V C630 1-126-157-11 ELECT 10uF 20% 16V C631 1-163-031-11 CERAMIC CHIP 0.01uF 50V C632 1-124-589-11 ELECT 47uF 20% 16V C633 1-107-725-11 CERAMIC CHIP 0.1uF 10% 16V

C634 1-163-031-11 CERAMIC CHIP 0.01uF 50V C701 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V

(RXD8/RXD8S)

C702 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V

(RXD8/RXD8S) C703 1-163-038-91 CERAMIC CHIP 0.1uF 25V C711 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V

(GRX80:EA3)

C712 1-163-019-00 CERAMIC CHIP 0.0068uF 10% 50V

(GRX80:EA3)

C713 1-126-160-11 ELECT 1uF 20% 50V

(GRX80:EA3)

C714 1-164-344-11 CERAMIC CHIP 0.068uF 10% 25V

(GRX80:EA3)

C715 1-124-465-00 ELECT 0.47uF 20% 50V

(GRX80:EA3)

C716 1-124-465-00 ELECT 0.47uF 20% 50V

(GRX80:EA3)

C717 1-164-492-11 CERAMIC CHIP 0.15uF 10% 16V

(GRX80:EA3)

C718 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V

(GRX80:EA3)

C719 1-126-160-11 ELECT 1uF 20% 50V

(GRX80:EA3)

C720 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V

(GRX80:EA3)

C721 1-163-019-00 CERAMIC CHIP 0.0068uF 10% 50V

(GRX80:EA3)

C722 1-164-344-11 CERAMIC CHIP 0.068uF 10% 25V

(GRX80:EA3)

C723 1-124-589-11 ELECT 47uF 20% 16V

(GRX80:EA3)

C724 1-163-038-91 CERAMIC CHIP 0.1uF 25V

(GRX80:EA3)

C725 1-124-589-11 ELECT 47uF 20% 16V

(GRX80:EA3)

C731 1-163-031-11 CERAMIC CHIP 0.01uF 50V

Ref. No. Part No. Description Remark

< CONNECTOR >

* CN601 1-568-867-11 SOCKET, CONNECTOR 25P

< DIODE >

D601 8-719-058-24 DIODE RB501V-40TE-17 D608 8-719-074-27 DIODE SELUIE10CXM-LC(LEFT) D609 8-719-074-24 DIODE SELUD10CXM-LC (RIGHT) D611 8-719-071-41 DIODE SELS5923C-TP15 (SYNC EQ) D612 8-719-071-44 DIODE SELS5223C-TP15 (EFFECT)

D613 8-719-071-41 DIODE SELS5923C-TP15 (SYNC BASS L) D614 8-719-071-41 DIODE SELS5923C-TP15 (SYNC BASS H) D615 8-719-063-93 DIODE SLR325VC-N-T32 (NON STOP) D619 8-719-056-13 DIODE SML79423C-TP15 (^) D620 8-719-073-47 DIODE SML72923C-TP15 (PAUSE/START, REC

D621 8-719-056-13 DIODE SML79423C-TP15 (AUTO BPM) D622 8-719-057-97 DIODE SEL5923A-TP15 (+/)) D623 8-719-057-97 DIODE SEL5923A-TP15 (-/0) D624 8-719-063-93 DIODE SLR325VC-N-T32 (JOG) D625 8-719-063-93 DIODE SLR325VC-N-T32 (ENTER/NEXT)

D626 8-719-057-97 DIODE SEL5923A-TP15 (GROOVE) D627 8-719-057-97 DIODE SEL5923A-TP15 (PAD A) D628 8-719-057-97 DIODE SEL5923A-TP15 (PAD B) D629 8-719-057-97 DIODE SEL5923A-TP15 (BEAT ON/OFF) D630 8-719-057-97 DIODE SEL5923A-TP15 (BEAT JAM)

D631 8-719-058-03 DIODE SEL5423E-TP15 (9 (B DECK)) D632 8-719-058-03 DIODE SEL5423E-TP15 (( (B DECK)) D633 8-719-058-03 DIODE SEL5423E-TP15 (9 (A DECK)) D634 8-719-058-03 DIODE SEL5423E-TP15 (( (A DECK)) D635 8-719-063-93 DIODE SLR325VC-N-T32 (TIMER SELECT)

D701 8-719-976-99 DIODE DTZ5.1B (GRX80:EA3)

< GROUND PLATE >

EP601 1-537-770-21 TERMINAL BOARD, GROUND

< FERRITE BEAD >

FB601 1-414-234-22 INDUCTOR CHIP 0UH FB602 1-414-234-22 INDUCTOR CHIP 0UH

C732 1-124-257-00 ELECT 2.2uF 20% 50V C733 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V C734 1-163-109-00 CERAMIC CHIP 47PF 5% 50V C735 1-126-157-11 ELECT 10uF 20% 16V C736 1-163-005-11 CERAMIC CHIP 470PF 10% 50V

C737 1-124-463-00 ELECT 0.1uF 20% 50V C738 1-124-257-00 ELECT 2.2uF 20% 50V

(GRX80:EA3) C739 1-163-109-00 CERAMIC CHIP 47PF 5% 50V C741 1-126-157-11 ELECT 10uF 20% 16V C742 1-163-251-11 CERAMIC CHIP 100PF 5% 50V

C743 1-124-257-00 ELECT 2.2uF 20% 50V C747 1-163-038-91 CERAMIC CHIP 0.1uF 25V C782 1-163-031-11 CERAMIC CHIP 0.01uF 50V C783 1-163-031-11 CERAMIC CHIP 0.01uF 50V C851 1-163-038-91 CERAMIC CHIP 0.1uF 25V

< FLUORESCENT INDICATOR >

FL601 1-517-831-11 INDICATOR TUBE, FLUORESCENT

< IC >

IC601 8-759-571-93 IC TMP88CS76F-6000 IC602 8-749-011-05 IC GP1U28X IC603 8-759-083-77 IC BA3830F IC604 8-759-342-19 IC NJU3716M-T2 IC605 8-759-577-80 IC MSM6654A-540GS-K

IC711 8-759-496-41 IC M65850FP-E1 (GRX80:EA3) IC712 8-759-636-55 IC M5218AFP

< JACK >

J701 1-785-569-11 JACK (SMALL TYPE)(HEADPHONES) J711 1-785-569-11 JACK (SMALL TYPE)(MIC 1)

– 91 –

Page 66

PANEL

Ref. No. Part No. Description Remark

< JUMPER RESISTOR >

JR501 1-216-296-91 SHORT 0 JR502 1-216-296-91 SHORT 0 JR503 1-216-295-91 SHORT 0 JR504 1-216-295-91 SHORT 0 JR505 1-216-295-91 SHORT 0

JR506 1-216-295-91 SHORT 0 JR507 1-216-295-91 SHORT 0 JR508 1-216-296-91 SHORT 0 JR509 1-216-296-91 SHORT 0 JR510 1-216-296-91 SHORT 0

JR511 1-216-296-91 SHORT 0 JR512 1-216-296-91 SHORT 0 JR513 1-216-296-91 SHORT 0 JR514 1-216-296-91 SHORT 0 JR515 1-216-296-91 SHORT 0

JR516 1-216-295-91 SHORT 0 JR517 1-216-296-91 SHORT 0

< COIL >

L601 1-412-029-11 INDUCTOR CHIP 10uH L602 1-412-032-11 INDUCTOR CHIP 100uH

< TRANSISTOR >

Ref. No. Part No. Description Remark

R617 1-216-097-91 RES,CHIP 100K 5% 1/10W R618 1-216-017-91 RES,CHIP 47 5% 1/10W R619 1-216-043-91 RES,CHIP 560 5% 1/10W R620 1-216-073-00 METAL CHIP 10K 5% 1/10W R621 1-216-073-00 METAL CHIP 10K 5% 1/10W

R622 1-216-035-00 METAL CHIP 270 5% 1/10W R623 1-216-037-00 METAL CHIP 330 5% 1/10W R624 1-216-041-00 METAL CHIP 470 5% 1/10W R625 1-216-043-91 RES,CHIP 560 5% 1/10W R626 1-216-045-00 METAL CHIP 680 5% 1/10W

R627 1-216-049-91 RES,CHIP 1K 5% 1/10W R628 1-216-051-00 METAL CHIP 1.2K 5% 1/10W R629 1-216-055-00 METAL CHIP 1.8K 5% 1/10W R630 1-216-059-00 METAL CHIP 2.7K 5% 1/10W R631 1-216-061-00 METAL CHIP 3.3K 5% 1/10W

R632 1-216-065-91 RES,CHIP 4.7K 5% 1/10W R633 1-216-069-00 METAL CHIP 6.8K 5% 1/10W R634 1-216-073-00 METAL CHIP 10K 5% 1/10W R635 1-216-077-00 METAL CHIP 15K 5% 1/10W R636 1-216-073-00 METAL CHIP 10K 5% 1/10W

R637 1-216-035-00 METAL CHIP 270 5% 1/10W R638 1-216-037-00 METAL CHIP 330 5% 1/10W R639 1-216-041-00 METAL CHIP 470 5% 1/10W R640 1-216-043-91 RES,CHIP 560 5% 1/10W R641 1-216-045-00 METAL CHIP 680 5% 1/10W

Q601 8-729-118-00 TRANSISTOR 2SB1116-L Q602 8-729-118-00 TRANSISTOR 2SB1116-L Q603 8-729-119-78 TRANSISTOR 2SC403SP-51 Q604 8-729-119-76 TRANSISTOR 2SA1175-HFE Q605 8-729-119-78 TRANSISTOR 2SC403SP-51

Q607 8-729-900-36 TRANSISTOR DTC124ES Q608 8-729-900-36 TRANSISTOR DTC124ES Q610 8-729-900-74 TRANSISTOR DTC143TS Q611 8-729-900-74 TRANSISTOR DTC143TS Q612 8-729-900-74 TRANSISTOR DTC143TS

Q613 8-729-900-74 TRANSISTOR DTC143TS Q614 8-729-900-74 TRANSISTOR DTC143TS Q615 8-729-900-74 TRANSISTOR DTC143TS Q616 8-729-900-74 TRANSISTOR DTC143TS Q620 8-729-119-76 TRANSISTOR 2SA1175-HFE

< RESISTOR >

R601 1-216-025-91 RES,CHIP 100 5% 1/10W R602 1-216-073-00 METAL CHIP 10K 5% 1/10W R603 1-216-025-91 RES,CHIP 100 5% 1/10W R604 1-216-025-91 RES,CHIP 100 5% 1/10W R605 1-216-073-00 METAL CHIP 10K 5% 1/10W

R606 1-216-017-91 RES,CHIP 47 5% 1/10W R607 1-216-111-00 METAL CHIP 390K 5% 1/10W R608 1-216-111-00 METAL CHIP 390K 5% 1/10W R609 1-216-097-91 RES,CHIP 100K 5% 1/10W R610 1-216-073-00 METAL CHIP 10K 5% 1/10W

R611 1-216-097-91 RES,CHIP 100K 5% 1/10W R612 1-216-017-91 RES,CHIP 47 5% 1/10W R613 1-216-085-00 METAL CHIP 33K 5% 1/10W R614 1-216-113-00 METAL CHIP 470K 5% 1/10W R616 1-216-121-91 RES,CHIP 1M 5% 1/10W

R642 1-216-049-91 RES,CHIP 1K 5% 1/10W R643 1-216-051-00 METAL CHIP 1.2K 5% 1/10W R644 1-216-055-00 METAL CHIP 1.8K 5% 1/10W R645 1-216-059-00 METAL CHIP 2.7K 5% 1/10W R646 1-216-061-00 METAL CHIP 3.3K 5% 1/10W

R647 1-216-065-91 RES,CHIP 4.7K 5% 1/10W R648 1-216-069-00 METAL CHIP 6.8K 5% 1/10W R649 1-216-073-00 METAL CHIP 10K 5% 1/10W R650 1-216-035-00 METAL CHIP 270 5% 1/10W R651 1-216-037-00 METAL CHIP 330 5% 1/10W

R652 1-216-041-00 METAL CHIP 470 5% 1/10W R653 1-216-043-91 RES,CHIP 560 5% 1/10W R654 1-216-045-00 METAL CHIP 680 5% 1/10W R655 1-216-073-00 METAL CHIP 10K 5% 1/10W R656 1-216-035-00 METAL CHIP 270 5% 1/10W

R657 1-216-037-00 METAL CHIP 330 5% 1/10W R658 1-216-041-00 METAL CHIP 470 5% 1/10W R659 1-216-043-91 RES,CHIP 560 5% 1/10W R660 1-216-045-00 METAL CHIP 680 5% 1/10W R661 1-216-049-91 RES,CHIP 1K 5% 1/10W

R662 1-216-051-00 METAL CHIP 1.2K 5% 1/10W R663 1-216-055-00 METAL CHIP 1.8K 5% 1/10W R664 1-216-059-00 METAL CHIP 2.7K 5% 1/10W R665 1-216-061-00 METAL CHIP 3.3K 5% 1/10W R666 1-216-065-91 RES,CHIP 4.7K 5% 1/10W

R667 1-216-069-00 METAL CHIP 6.8K 5% 1/10W R668 1-216-073-00 METAL CHIP 10K 5% 1/10W R669 1-216-077-00 METAL CHIP 15K 5% 1/10W R670 1-216-083-00 METAL CHIP 27K 5% 1/10W R671 1-216-091-00 METAL CHIP 56K 5% 1/10W

R672 1-216-049-91 RES,CHIP 1K 5% 1/10W R673 1-216-089-91 RES,CHIP 47K 5% 1/10W

– 92 –

Page 67

PANEL

Ref. No. Part No. Description Remark

R674 1-216-049-91 RES,CHIP 1K 5% 1/10W R675 1-216-073-00 METAL CHIP 10K 5% 1/10W R676 1-216-089-91 RES,CHIP 47K 5% 1/10W

R677 1-216-089-91 RES,CHIP 47K 5% 1/10W R678 1-216-073-00 METAL CHIP 10K 5% 1/10W R680 1-216-073-00 METAL CHIP 10K 5% 1/10W R681 1-216-073-00 METAL CHIP 10K 5% 1/10W R682 1-216-073-00 METAL CHIP 10K 5% 1/10W

R683 1-216-073-00 METAL CHIP 10K 5% 1/10W R684 1-216-073-00 METAL CHIP 10K 5% 1/10W R685 1-216-073-00 METAL CHIP 10K 5% 1/10W R686 1-216-097-91 RES,CHIP 100K 5% 1/10W R687 1-216-097-91 RES,CHIP 100K 5% 1/10W

R688 1-216-073-00 METAL CHIP 10K 5% 1/10W R689 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R691 1-216-097-91 RES,CHIP 100K 5% 1/10W R692 1-216-097-91 RES,CHIP 100K 5% 1/10W R693 1-216-097-91 RES,CHIP 100K 5% 1/10W

R694 1-216-097-91 RES,CHIP 100K 5% 1/10W R695 1-216-097-91 RES,CHIP 100K 5% 1/10W R696 1-216-097-91 RES,CHIP 100K 5% 1/10W R697 1-216-097-91 RES,CHIP 100K 5% 1/10W R698 1-216-057-00 METAL CHIP 2.2K 5% 1/10W

R699 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R701 1-216-017-91 RES,CHIP 47 5% 1/10W

(GRX80:EA3) R711 1-216-081-00 METAL CHIP 22K 5% 1/10W

(GRX80:EA3) R712 1-216-081-00 METAL CHIP 22K 5% 1/10W

(GRX80:EA3) R713 1-216-081-00 METAL CHIP 22K 5% 1/10W

(GRX80:EA3)

Ref. No. Part No. Description Remark

R754 1-216-029-00 METAL CHIP 150 5% 1/10W

R758 1-216-022-00 METAL CHIP 75 5% 1/10W R759 1-216-022-00 METAL CHIP 75 5% 1/10W R760 1-216-022-00 METAL CHIP 75 5% 1/10W R761 1-216-022-00 METAL CHIP 75 5% 1/10W R762 1-216-029-00 METAL CHIP 150 5% 1/10W

R763 1-216-029-00 METAL CHIP 150 5% 1/10W R764 1-216-019-00 METAL CHIP 56 5% 1/10W R765 1-216-019-00 METAL CHIP 56 5% 1/10W R766 1-216-029-00 METAL CHIP 150 5% 1/10W R767 1-216-022-00 METAL CHIP 75 5% 1/10W

R768 1-216-029-00 METAL CHIP 150 5% 1/10W R769 1-216-029-00 METAL CHIP 150 5% 1/10W R770 1-216-029-00 METAL CHIP 150 5% 1/10W R771 1-216-029-00 METAL CHIP 150 5% 1/10W R772 1-216-029-00 METAL CHIP 150 5% 1/10W

R773 1-216-022-00 METAL CHIP 75 5% 1/10W R775 1-216-029-00 METAL CHIP 150 5% 1/10W R776 1-216-019-00 METAL CHIP 56 5% 1/10W R777 1-216-025-91 RES,CHIP 100 5% 1/10W R778 1-216-025-91 RES,CHIP 100 5% 1/10W

R780 1-216-073-00 METAL CHIP 10K 5% 1/10W R781 1-216-029-00 METAL CHIP 150 5% 1/10W R782 1-216-029-00 METAL CHIP 150 5% 1/10W R783 1-216-073-00 METAL CHIP 10K 5% 1/10W R784 1-216-081-00 METAL CHIP 22K 5% 1/10W

R785 1-216-081-00 METAL CHIP 22K 5% 1/10W R786 1-216-049-91 RES,CHIP 1K 5% 1/10W R787 1-216-095-00 METAL CHIP 82K 5% 1/10W R788 1-216-089-91 RES,CHIP 47K 5% 1/10W R789 1-216-095-00 METAL CHIP 82K 5% 1/10W

R714 1-216-089-91 RES,CHIP 47K 5% 1/10W

(GRX80:EA3) R715 1-216-081-00 METAL CHIP 22K 5% 1/10W

(GRX80:EA3) R716 1-216-077-00 METAL CHIP 15K 5% 1/10W

(GRX80:EA3) R717 1-216-081-00 METAL CHIP 22K 5% 1/10W

(GRX80:EA3) R718 1-216-081-00 METAL CHIP 22K 5% 1/10W

(GRX80:EA3)

R719 1-216-099-00 METAL CHIP 120K 5% 1/10W

(GRX80:EA3) R721 1-216-073-00 METAL CHIP 10K 5% 1/10W R722 1-216-049-91 RES,CHIP 1K 5% 1/10W R723 1-216-097-91 RES,CHIP 100K 5% 1/10W R724 1-216-049-91 RES,CHIP 1K 5% 1/10W

R725 1-216-081-00 METAL CHIP 22K 5% 1/10W R725 1-216-089-91 RES,CHIP 47K 5% 1/10W

(GRX80:EA3) R726 1-216-073-00 METAL CHIP 10K 5% 1/10W R727 1-216-077-00 METAL CHIP 15K 5% 1/10W

(GRX80:EA3) R728 1-216-103-00 METAL CHIP 180K 5% 1/10W

R729 1-216-025-91 RES,CHIP 100 5% 1/10W R751 1-216-029-00 METAL CHIP 150 5% 1/10W R752 1-216-029-00 METAL CHIP 150 5% 1/10W R753 1-216-029-00 METAL CHIP 150 5% 1/10W

R790 1-216-055-00 METAL CHIP 1.8K 5% 1/10W

< VARIABLE RESISTOR >

RV711 1-225-739-11 RES, VAR 50K (GRX80:EA3) RV712 1-225-739-11 RES, VAR 50K

< SWITCH >

S601 1-473-534-11 ENCODER, ROTARY (JOG/0 ˜ )) S602 1-473-392-11 ENCODER, ROTARY (VOLUME) S611 1-762-875-21 SWITCH, KEYBOARD (SYNC BASE) S612 1-762-875-21 SWITCH, KEYBOARD (SYNC EQ) S613 1-762-875-21 SWITCH, KEYBOARD (KARAOKE PON/MPX)

S614 1-762-875-21 SWITCH, KEYBOARD (NON STOP) S615 1-762-875-21 SWITCH, KEYBOARD (SURROUND) S616 1-762-875-21 SWITCH, KEYBOARD (DBFB) S617 1-762-875-21 SWITCH, KEYBOARD (ENTER/NEXT) S618 1-762-875-21 SWITCH, KEYBOARD (+/))

S619 1-762-875-21 SWITCH, KEYBOARD (-/0) S620 1-762-875-21 SWITCH, KEYBOARD (GROOVE) S621 1-762-875-21 SWITCH, KEYBOARD (PAD B) S622 1-762-875-21 SWITCH, KEYBOARD (BEAT SPEED) S623 1-762-875-21 SWITCH, KEYBOARD (BEAT SEL)

S624 1-762-875-21 SWITCH, KEYBOARD (BEAT ON/OFF) S625 1-762-875-21 SWITCH, KEYBOARD (REC) S626 1-762-875-21 SWITCH, KEYBOARD (HI DVB)

– 93 –

Page 68

PANEL

SENSOR

SUB TRANS

TRANS

Ref. No. Part No. Description Remark

S627 1-762-875-21 SWITCH, KEYBOARD (CD SYNC) S628 1-762-875-21 SWITCH, KEYBOARD (PAD A)

S629 1-762-875-21 SWITCH, KEYBOARD (BEAT MIX) S630 1-762-875-21 SWITCH, KEYBOARD (BEAT JAM) S631 1-762-875-21 SWITCH, KEYBOARD (BEAT LEVEL) S636 1-762-875-21 SWITCH, KEYBOARD (AUTO BPM) S637 1-762-875-21 SWITCH, KEYBOARD (FLASH)

S638 1-762-875-21 SWITCH, KEYBOARD (P FILE MEMORY) S639 1-762-875-21 SWITCH, KEYBOARD (GEQ CONTROL) S640 1-762-875-21 SWITCH, KEYBOARD (FILE SELECT) S641 1-762-875-21 SWITCH, KEYBOARD (EFFECT) S642 1-762-875-21 SWITCH, KEYBOARD (TUNER/BAND)

S643 1-762-875-21 SWITCH, KEYBOARD (^) S644 1-762-875-21 SWITCH, KEYBOARD (p) S645 1-762-875-21 SWITCH, KEYBOARD (B:() S646 1-762-875-21 SWITCH, KEYBOARD (B:9) S647 1-762-875-21 SWITCH, KEYBOARD (A:()

S648 1-762-875-21 SWITCH, KEYBOARD (A:9) S649 1-762-875-21 SWITCH, KEYBOARD (FANCTION) S650 1-762-875-21 SWITCH, KEYBOARD (LOOP) S651 1-762-875-21 SWITCH, KEYBOARD (DISPLAY) S652 1-762-875-21 SWITCH, KEYBOARD (CLOCK/TIME SET)

S653 1-762-875-21 SWITCH, KEYBOARD (TIME SELECT) S654 1-762-875-21 SWITCH, KEYBOARD (SPECTRUM ANALYZER) S655 1-762-875-21 SWITCH, KEYBOARD (REPEAT STEREO/MONO) S656 1-762-875-21 SWITCH, KEYBOARD (PLAY MODE DOLBY ON) S657 1-762-875-21 SWITCH, KEYBOARD

(EDIT DIRECTION TUNER MEMORY)

< VIBRATOR >

Ref. No. Part No. Description Remark * CN12 1-564-321-21 PIN, CONNECTOR 2P

CN13 1-785-333-11 PIN, CONNECTOR (LIGHT ANGLE)7P

< DIODE >

D11 8-719-911-19 DIODE 1SS119-25 D12 8-719-210-21 DIODE 11EQS04 D13 8-719-210-21 DIODE 11EQS04 D14 8-719-210-21 DIODE 11EQS04 D15 8-719-210-21 DIODE 11EQS04

D16 8-719-911-19 DIODE 1SS119-25 D17 8-719-024-99 DIODE 11ES2-NTA2B D18 8-719-024-99 DIODE 11ES2-NTA2B D19 8-719-024-99 DIODE 11ES2-NTA2B D20 8-719-024-99 DIODE 11ES2-NTA2B

D21 8-719-986-60 DIODE HZS27-3LTA D22 8-719-109-63 DIODE RD3.0ESB2 D23 8-719-911-19 DIODE 1SS119-25

< IC >

IC11 8-759-450-47 IC BA05T

< TRANSISTOR >

Q11 8-729-119-78 TRANSISTOR 2SC403SP-51 Q12 8-729-040-19 TRANSISTOR RT1N137L-TP Q13 8-729-118-01 TRANSISTOR 2SB1116 Q14 8-729-048-13 TRANSISTOR 2SC3616-KLM-T1 Q15 8-729-048-13 TRANSISTOR 2SC3616-KLM-T1

Q16 8-729-900-63 TRANSISTOR DTA124ES Q17 8-729-900-63 TRANSISTOR DTA124ES

X601 1-781-312-11 VIBRATOR, CERAMIC (12.5MHz) X602 1-767-353-11 VIBRATOR, CERAMIC (4.98MHz)

**************************************************************

* 1-658-576-11 SENSOR BOARD

************

< IC >

IC702 8-749-924-18 IC PHOTO INTERRUPTER RPI-1391 IC703 8-749-924-30 IC PHOTO REFLECTOR GP2S28

**************************************************************

* A-4417-646-A SUB TRANS BOARD, COMPLETE (RXD8/RXD8S)

**************************

< CAPACITOR >

C11 1-126-768-11 ELECT 2200uF 20% 16V C12 1-161-494-00 CERAMIC 0.022uF 25V C13 1-126-933-11 ELECT 100uF 20% 16V C14 1-126-968-11 ELECT 100uF 20% 50V C15 1-164-159-11 CERAMIC 0.1uF 50V

C16 1-126-948-11 ELECT 100uF 20% 35V

! C21 1-113-925-11 CERAMIC 0.01uF 20% 250V

< CONNECTOR >

CN11 1-564-321-00 PIN, CONNECTOR 2P

< RESISTOR >

R11 1-249-429-11 CARBON 10K 5% 1/4W R12 1-249-429-11 CARBON 10K 5% 1/4W R13 1-249-417-11 CARBON 1K 5% 1/4W F R15 1-249-429-11 CARBON 10K 5% 1/4W R16 1-247-807-31 CARBON 100 5% 1/4W

R17 1-247-807-31 CARBON 100 5% 1/4W R18 1-247-807-31 CARBON 100 5% 1/4W R19 1-249-417-11 CARBON 1K 5% 1/4W F R20 1-247-807-31 CARBON 100 5% 1/4W

< RELAY >

! RY11 1-755-276-11 RELAY, POWER

< TRANSFORMER >

! T11 1-433-591-11 TRANSFORMER, POWER

**************************************************************

* 1-672-474-11 TRANS BOARD

***********

< CAPACITOR >

C971 1-128-563-11 ELECT 100uF 20% 100V

(GRX80)

C972 1-126-960-11 ELECT 1uF 20% 50V

(GRX80)

– 94 –

The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.

Page 69

TRANS

Ref. No. Part No. Description Remark

C973 1-126-947-11 ELECT 47uF 20% 35V

(GRX80)

< CONNECTOR >

CN901 1-564-524-11 PLUG, CONNECTOR 9P (RXD8/RXD8S)

* CN901 1-564-527-11 PLUG, CONNECTOR 12P (GRX80)

CN902 1-785-329-11 PIN, CONNECTOR (LIGHT ANGLE) 3P (GRX80) CN951 1-564-321-00 PIN, CONNECTOR 2P (GRX80)

< DIODE >

D971 8-719-024-99 DIODE 11ES2-NTA2B (GRX80) D972 8-719-056-97 DIODE UDZ-TE-17-27B (GRX80) D973 8-719-056-74 DIODE UDZ-TE-17-3.0B (GRX80)

< FUSE >

! F951 1-532-506-31 FUSE (T6.3AL/250V)

(GRX80:E2,E3,EA3,SP,AR,TW,MX)

! F952 1-532-465-31 FUSE (3.15A/250V)

(GRX80:E2,E3,EA3,SP,AR,TW,AUS,EA4,TH)

! F953 1-532-465-31 FUSE (3.15A/250V)

(GRX80:E2,E3,EA3,SP,AR,TW,AUS,EA4,TH)

! F961 1-532-505-31 FUSE (T5AL/250V)(GRX80) ! F962 1-532-505-31 FUSE (T5AL/250V)(GRX80)

! F963 1-533-949-31 FUSE, CYLINDRICAL (T8AL/250V)(RXD8/RXD8S) ! F964 1-533-949-31 FUSE, CYLINDRICAL (T8AL/250V)(RXD8/RXD8S)

< FUSE HOLDER >

FH951 1-533-233-21 HOLDER, FUSE

(GRX80:E2,E3,EA3,SP,AR,TW,MX)

FH952 1-533-233-21 HOLDER, FUSE

(GRX80:E2,E3,EA3,SP,AR,TW,MX)

FH953 1-533-233-21 HOLDER, FUSE

(GRX80:E2,E3,EA3,SP,AR,TW,EA4,TH)

FH954 1-533-233-21 HOLDER, FUSE

(GRX80:E2,E3,EA3,SP,AR,TW,EA4,TH)

FH955 1-533-233-21 HOLDER, FUSE

(GRX80:E2,E3,EA3,SP,AR,TW,AUS)

FH956 1-533-233-21 HOLDER, FUSE

(GRX80:E2,E3,EA3,SP,AR,TW,AUS) FH961 1-533-233-21 HOLDER, FUSE (GRX80) FH962 1-533-233-21 HOLDER, FUSE (GRX80) FH963 1-533-233-21 HOLDER, FUSE (GRX80) FH964 1-533-233-21 HOLDER, FUSE (GRX80)

FH965 1-533-233-21 HOLDER, FUSE (RXD8/RXD8S) FH966 1-533-233-21 HOLDER, FUSE (RXD8/RXD8S) FH967 1-533-233-21 HOLDER, FUSE (RXD8/RXD8S) FH968 1-533-233-21 HOLDER, FUSE (RXD8/RXD8S)

< TRANSISTOR >

Q971 8-729-048-52 TRANSISTOR 2SA1932(TP)(GRX80)

< RESISTOR >

! R951 1-219-120-11 FUSIBLE 0.15 5% 1/4W F

(GRX80)

! R951 1-219-122-91 FUSIBLE 0.33 5% 1/4W F

(RXD8/RXD8S)

! R952 1-219-120-11 FUSIBLE 0.15 5% 1/4W F

(GRX80)

! R952 1-219-122-91 FUSIBLE 0.33 5% 1/4W F

(RXD8/RXD8S)

Ref. No. Part No. Description Remark

! R953 1-219-119-81 FUSIBLE 0.1 5% 1/4W F

(RXD8/RXD8S)

! R953 1-219-120-11 FUSIBLE 0.15 5% 1/4W F

(GRX80)

R971 1-216-455-11 METAL OXIDE 560 5% 2W F

(GRX80)

R972 1-216-085-00 METAL CHIP 33K 5% 1/10W

(GRX80)

R973 1-216-073-00 METAL CHIP 10K 5% 1/10W

(GRX80)

R974 1-216-025-91 RES,CHIP 100 5% 1/10W

(GRX80)

R975 1-216-025-91 RES,CHIP 100 5% 1/10W

(GRX80)

R976 1-216-085-00 METAL CHIP 33K 5% 1/10W

(GRX80)

R977 1-216-085-00 METAL CHIP 33K 5% 1/10W

(GRX80)

< SWITCH >

S951 1-771-291-11 SWITCH, POWER (VOLTAGE SELECTOR)

(GRX80:E2,E3,EA3,SP,AR,TW)

< TRANSFORMER >

! T951 1-433-556-11 TRANSFORMER, POWER (GRX80) ! T951 1-433-557-11 TRANSFORMER, POWER (RXD8/RXD8S)

**************************************************************

MISCELLANEOUS

*************

5 1-233-545-11 TUNER UNIT (EA4,TH) 5 1-233-545-14 ENCAPSULATED COMPONENT (E2,AR,MX,AUS) 5 1-233-546-13 ENCAPSULATED COMPONENT (E3,EA3,SP,TW) 5 1-693-443-11 TUNER UNIT (AEP,UK,G,CIS) 54 1-783-570-11 WIRE (FLAT TYPE)(19 CORE)

55 1-769-977-11 WIRE (FLAT TYPE)(13 CORE) 55 1-773-009-11 WIRE (FLAT TYPE)(15 CORE)(150mm) 56 1-773-024-11 WIRE (FLAT TYPE)(15 CORE)(320mm) 58 1-569-007-11 ADAPTOR, CONVERSION 2P (E3) 58 1-569-008-21 ADAPTOR, CONVERSION 2P (EA3,SP,TW)

58 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (UK)

! 59 1-575-651-11 CORD, POWER (AEP,UK,G,CIS,EA3,SP,TW) ! 59 1-575-653-11 CORD, POWER (E2,E3,MX,TH) ! 59 1-690-608-11 CORD, POWER (AUS) ! 59 1-783-721-11 CORD, POWER (EA4)

! 59 1-783-941-21 CORD, POWER (GRX80:AR)

62 1-773-042-11 WIRE (FLAT TYPE)(17 CORE) 116 1-773-223-11 WIRE (FLAT TYPE)(25 CORE) 257 1-452-925-21 MAGNET ASSY 258 1-776-042-11 WIRE (FLAT TYPE) (8 CORE)

! 301 8-820-020-02 OPTICAL PICK-UP KSS-213D/Q-NP

302 1-769-069-11 WIRE (FLAT TYPE) (16 CORE) FL601 1-517-831-11 INDICATOR TUBE, FLUORESCENT HP101 A-2056-681-A DECK (A) ASSY, HEAD (230AWR2) HP101 A-2056-681-B DECK (A) ASSY, HEAD (230PWR2)

HRPE101 A-2056-682-A DECK (B) ASSY, HEAD (230AWR2) HRPE101 A-2056-682-B DECK (B) ASSY, HEAD (230PWR2)

– 95 –

The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.

Page 70

HCD-GRX80/RXD8/RXD8S

Ref. No. Part No. Description Remark

M1 A-2004-628-A MOTOR ASSY, CAPSTAN M101 X-4917-523-3 MOTOR ASSY (SPINDLE) M102 X-4917-504-1 MOTOR ASSY (SLED)

M701 A-4672-004-A MOTOR ASSY M901 1-763-072-11 FAN, D.C. S811 1-473-335-11 ENCODER, ROTARY

! T11 1-433-591-11 TRANSFORMER, POWER (RXD8/RXD8S) ! T951 1-433-556-11 TRANSFORMER, POWER (GRX80)

! T951 1-433-557-11 TRANSFORMER, POWER (RXD8/RXD8S)

**************************************************************

*************

HARDWARE LIST

*************

#1 7-685-871-01 SCREW +BVTT 3X6 (S) #2 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S #3 7-685-880-09 SCREW +BVTT 4X6 (S) #4 7-685-650-79 SCREW +BVTP 3X16 TYPE2 IT-3 #5 7-685-852-04 SCREW +BVTT 2X5 (S)

#7 7-682-553-04 SCREW +P 3X20 #8 7-685-851-04 SCREW +BVTT 2X4 (S) #9 7-628-254-15 SCREW +PS 2.6X6 #10 7-628-254-50 SCREW +PS 2.6X16 #11 7-685-861-01 SCREW +BVTT 2.6X5 (S)

– 96 –

The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.

Page 71

MEMO

HCD-GRX80/RXD8/RXD8S

– 97 –

Page 72

HCD-GRX80/RXD8/RXD8S

REVISION HISTORY

Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page.

Ver. Date Description of Revision

1.1 2001.06 Correction of exploded views (108, 123). (SPM-01018)

1.0 1999.02 New.

Sony HCD-GRX80, HCD-RXD8, HCD-RXD8S Service manual

Specifications and Main Features

Frequently Asked Questions

User Manual

SERVICING NOTE

GENERAL

DISASSEMBLY

SER VICE MODE

MECHANICAL ADJUSTMENTS

ELECTRICAL ADJUSTMENTS

DIAGRAMS