Sony DCR-DVD105, Handycam DCR-DVD105, Handycam DCR-DVD105E, Handycam DCR-DVD605, Handycam DCR-DVD605E Service Manual

SERVICE MANUAL

Sony EMCS Co.

LEVEL 2

Link

SERVICE NOTE

MODEL INFORMATION TABLE

SPECIFICATIONS

BLOCK DIAGRAMS

SCHEMATIC DIAGRAMS

DISASSEMBLY

REPAIR PARTS LIST

PRINTED WIRING BOARDS

Link

Revision History

Revision History

How to use

Acrobat Reader

How to use

Acrobat Reader

DCR-DVD105/DVD105E/DVD605/DVD605E_L2

Ver 1.0 2005.12

DIGITAL VIDEO CAMERA RECORDER

Photo: DCR-DVD105

The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part num­ber specified.

Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.

2005L0500-1

© 2005.12

Published by DI Technical Support Department

9-876-924-31

US Model

Canadian Model

AEP Model

UK Model

East European Model

North European Model

E Model

Australian Model

Hong Kong Model

Chinese Model

Korea Model

Argentine Model

Brazilian Model

DCR-DVD105/DVD105E/

DVD605/DVD605E

— 2 —

DCR-DVD105/DVD105E/DVD605/DVD605E_L2

SPECIFICATIONS

These specifications are extracted from instruction
manual of DCR-DVD105E/DVD605E.

System

Video compression format

MPEG2/JPEG (Still images)

Audio compression format

Dolby Digital 2ch
Dolby Digital Stereo Creator

Video signal

PAL color, CCIR standards

Usable discs

8cm DVD-R/DVD-RW/DVD+RW

Recording format

Movie

DVD-R: DVD-VIDEO
DVD-RW: DVD-VIDEO (VIDEO mode),

DVD-Video Recording
(VR mode)

DVD+RW:DVD+RW Video

Still image

Exif

*1

Ver.2.2

Recording/playback time

HQ:Approx. 20 min
SP: Approx. 30 min
LP: Approx. 60 min

Viewfinder

Electric viewfinder
color

Image device

3 mm (1/6 type) CCD (Charge Coupled Device)
Gross:
Approx. 800 000 pixels
Effective (Movie):
Approx. 400 000 pixels
Effective (Still):
Approx. 400 000 pixels

Lens

Carl Zeiss Vario-Tessar
Filter diameter: 25mm (1 in.)
Optical:20×, Digital:40×, 800×
F=1.8-3.1

Focal length

f=2.3 - 46mm (3/32 - 1 13/16 in.)
When converted to a 35 mm still camera
For movies:
44 - 880mm (1 3/4 - 34 1/32 in.)
For still images:
44 - 880mm (1 3/4 - 34 1/32 in.)

Color temperature

[AUTO], [ONE PUSH], [INDOOR] (3 200 K),
[OUTDOOR] (5 800 K)

Minimum illumination

5 lx (lux) (F1.8)
0 lx (lux) (in the NightShot plus function)

*2

*1

“Exif” is a file format for still images, established
by the JEIT A (Japan Electronics and Information
Technology Industries Association). Files in this
format can have additional information such as
your camcorder’s setting information at the time
of recording.

*2

Objects unable to be seen due to the dark can be
shot with infrared lighting.

•Manufactured under license from Dolby
Laboratories.

Input/Output connectors

Audio/Video output

10 pin connector
Video signal: 1 Vp-p, 75 Ω (ohms), unbalanced
Luminance signal: 1 Vp-p, 75 Ω (ohms),
unbalanced
Chrominance signal: 0.3 Vp-p, 75 Ω (ohms),
unbalanced
Audio signal: 327 mV (at Load impedance
47 kΩ (kilohms)), Output impedance less than

2.2 kΩ (kilohms)

LCD screen

Picture

6.2 cm (2.5 type)

Tot al number of pixels

123 200 (560 × 220)

General

Power requirements

7.2 V (battery pack)

8.4 V (AC Adaptor)

Average power consumption

During camera recording using LCD
Viewfinder

Operating temperature

0°C to + 40°C (32°F to 104°F)

Storage temperature

-20°C to + 60°C (-4°F to + 140°F)

Dimensions (Approx.)

54 × 88 × 129mm (2 1/4 × 3 1/2 × 5 1/8 in.)
(w × h × d)

Mass (Approx.)

380 g (13 oz) main unit only
430 g (15 oz) including the NP-FP50
rech

AC Adaptor (1)
Mains lead (1)
A/V connecting cable (1)
Rechargeable battery pack
NP-FP50 (1)
Cleaning cloth (1)
Lens cap (1)
Operating Guide (This manual) (1)

argeable battery pack and disc

Supplied accessories

AC Adaptor AC-L25A/L25B

Power requirements

AC 100 - 240 V, 50/60 Hz

Current consumption

0.35 - 0.18 A

Power consumption

18W

Output voltage

DC 8.4V*

Operating temperature

0°C to + 40°C (32°F to 104°F)

Storage temperature

-20°C to + 60°C (-4°F to + 140°F)

Dimensions (Approx.)

56 × 31 × 100 mm (2 1/4 × 1 1/4 × 4 in.)
(w × h × d) excluding the projecting parts

Mass (Approx.)

190 g (6.7 oz) excluding the mains lead

* See at the label of AC Adaptor for other

specifications.

Rechargeable battery pack NP-FP50

Maximum output voltage

DC8.4V

Output voltage

DC7.2V

Capacity

4.9 wh (680 mAh)

Dimensions (Approx.)

31.8 × 18.5 × 45.0 mm
(1 5/16 × 3/4 × 1 13/16 in.) (w× h×d)

Mass (Approx.)

40 g (1.5 oz)

Operating temperature

0°C to + 40°C (32°F to 104°F)

Typ e

Li-ion

Design and specifications are subject to change
without notice.

— 3 —

DCR-DVD105/DVD105E/DVD605/DVD605E_L2

Model information table

•Abbreviation
AR : Argentine model
AUS: Australian model
BR : Brazilian model
CH : Chinese model
CND: Canadian model
EE : East European model
HK : Hong Kong model
JE : Tourist model
KR : Korea model
MX : Mexican Model
NE : North European model

Model DCR-DVD105 DCR-DVD105E DVR-DVD605 DCR-DVD605E
Destination US, CND, E, AR, BR AEP, UK, NE, EE E, KR E, HK, AUS, CH
Color system NTSC PAL NTSC PAL

— 4 —

DCR-DVD105/DVD105E/DVD605/DVD605E_L2

1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.

2. Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair . Point
them out to the customer and recommend their replacement.

4. Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.

5. Check the B+ voltage to see it is at the values specified.

6. Flexible Circuit Board Repairing

•Keep the temperature of the soldering iron around 270˚C
during repairing.

• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering
or unsoldering.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.

Unleaded solder

Boards requiring use of unleaded solder are printed with the lead­free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)

: LEAD FREE MARK

Unleaded solder has the following characteristics.

• Unleaded solder melts at a temperature about 40°C higher than

ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!

• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.

• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY .

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS P AR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMA TIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

WARNING!!

WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION,
BE SURE TO OBSER VE FR OM A DIST ANCE OF MORE
THAN 30 cm FROM THE SURFACE OF THE
OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.

CAUTION:

The use of optical instrument with this product will increase eye
hazard.

CAUTION :

Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.

CAUTION
Use of controls or adjustments or performance
procedures other than those specified herein may
result in hazardous radiation exposure.

— 5 —

DCR-DVD105/DVD105E/DVD605/DVD605E_L2

TABLE OF CONTENTS

1. SERVICE NOTE

1-1. Power Supply During Repairs········································· 1-1
1-2. To Take Out a Disc when not Eject (Force Eject) ···········1-1
1-3. Setting The “Forced Power On” Mode····························1-1
1-4. Using Service Jig·····························································1-2
1-5. Self-diagnosis Function ···················································1-2
1-6. Precaution on Replacing The VC-421 Board ··················1-4

2. DISASSEMBLY

2-1. Disassembly·····································································2-2

3. BLOCK DIAGRAMS

3-1. Overall Block Diagram (1/5)···········································3-1
3-2. Overall Block Diagram (2/5)···········································3-3
3-3. Overall Block Diagram (3/5)···········································3-5
3-4. Overall Block Diagram (4/5)···········································3-7
3-5. Overall Block Diagram (5/5)···········································3-9
3-6. Power Block Diagram (1/3)··········································· 3-11
3-7. Power Block Diagram (2/3)··········································· 3-13
3-8. Power Block Diagram (3/3)··········································· 3-15

4. PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS

4-1. Schematic Diagrams························································4-1
4-2. Printed Wiring Boards ···················································4-51
4-3. Waveforms ·····································································4-73
4-4. Mounted Parts Location ················································4-79

5. REPAIR PARTS LIST

5-1. Exploded V iews ·······························································5-2
5-2. Electrical Parts List························································5-12

Section Title Page

1-1

DCR-DVD105/DVD105E/DVD605/DVD605E_L2

1. SERVICE NOTE

1-1. POWER SUPPLY DURING REPAIRS

In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the po wer is shut of f so
that the unit cannot operate.
These following method is available to prevent this.

Method:

Use the AC power adaptor (AC-L25A/L25B).

1-2. TO TAKE OUT A DISC WHEN NOT EJECT (FORCE EJECT)

1 Peel off the remote control window and remote control window sheet.
2 Insert the wire etc. in the hole and lift the eject slider by it.

Eject slider

Remote control window

Remote control window sheet

Hole

Eject charge
lever

1-3. SETTING THE “FORCED POWER ON” MODE

It is possible to turn on power by adjustment remote commander (RM-95 or NEW LANC JIG).
Operate the camcorder using the adjustment remote commander.

1-3-1. Setting the “Forced Movie Power ON” Mode

1) Select page: 0, address: 01, and set data:01.

2) Select page: A, address: 10, set data:01 and press the “PAUSE (Write)” button of the adjustment remote commander.

1-3-2. Setting the “Forced Play/Edit Power ON” Mode

1) Select page: 0, address: 01, and set data:01.

2) Select page: A, address: 10, set data:02 and press the “PAUSE (Write)” button of the adjustment remote commander.

1-3-3. Exiting the “Forced Power ON” Mode

1) Select page: 0, address: 01, and set data:01.

2) Select page: A, address: 10, set data:00 and press the “PAUSE (Write)” button of the adjustment remote commander.

3) Select page: 0, address: 01, and set data: 00.

1-2

DCR-DVD105/DVD105E/DVD605/DVD605E_L2

1-5. SELF-DIAGNOSIS FUNCTION

1-5-1. Self-diagnosis Function

When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the viewfinder or LCD
screen what to do. This function consists of two display; self­diagnosis display and service mode display.
Details of the self-diagnosis functions are provided in the Instruction
manual.

1-5-2. Self-diagnosis Display

When problems occur while the unit is operating, the counter of the
viewfinder or LCD screen shows a 4-digit display consisting of an
alphabet and numbers, which blinks at 3.2 Hz. This 5-character
display indicates the “repaired by:”, “block” in which the problem
occurred, and “detailed code” of the problem.

1 1

3 1C

Repaired by:

Refer to “1-5-3. Self-diagnosis Code Table”.

Indicates the appropriate
step to be taken.
E.g.

31 ....Reload the tape.

32 ....Turn on power again.

Block

Detailed Code

Blinks at 3.2Hz

C : Corrected by customer
H : Corrected by dealer
E : Corrected by service

engineer

Viewfinder or LCD screen

C : 3 1 : 1 1

DVD mechanism deck

VC-421 board (side B

)

Flexible board
(from DVD mechanism deck (10P))

Extension cable (10P)

(J-6082-572-A)

CN1009

1-4. USING SERVICE JIG

Connect the extension cable (J-6082-572-A) between the DVD mechanism deck and CN1009 on the VC-421 board.

1-3

DCR-DVD105/DVD105E/DVD605/DVD605E_L2

1-5-3. Self-diagnosis Code Table

C
C
C

C
C

E
E

E

E

E

E

E

E

E

E

E

Block

Function

04
13
13

21
32

20
31

40

40

61

61

61

62

62

94

94

Detailed

Code

00
00
02

00
50

00
00

00

01

00

10

11

00

01

00

01

Symptom/State

Non-standard battery is used.
Faulty disc is used.
Disc access error

Condensation.
Codec IC dose not return are reply

EEPROM data are rewritten.
Drive fault

Codec IC fault

Audio Codec IC fault

Difficult to adjust focus
(Cannot initialize focus.)

Zoom operations fault
(Cannot initialize zoom lens.)

The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.

Handshake correction function does not
work well. (With PITCH angular
velocity sensor output stopped.)

Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)

Fault of writing to or erasing the flash
memory

Fault of writing to or erasing EEPROM

Self-diagnosis Code

Repaired by:

Correction

Use the InfoLITHIUM battery.
Use a compatible disc with the camcorder.
Clean the disc with the supplied cleaning cloth.

Use a compatible disc with the camcorder.
Remove the disc, and insert it again after one hour.
Remove the power source. Reconnect it again and operate your

camcorder again
Make EEPROM data correct value. (Note)
Inspect or replacement of the mechanism deck, IC (IC4302 on

the VC-421 board) and drive block
Inspect or replacement of the codec IC (IC3001on the VC-421

board) peripheral circuits
Inspect or replacement of the Audio Codec IC (IC3001 on the

VC-421 board) peripheral circuits
Inspect the lens block focus reset sensor (pin ql of CN1301 on

the VC-421 board) when focusing is performed when the touch
panel is operated in the focus manual mode and the focus motor
drive circuit (IC1301on the VC-421 board) when the focusing is
not performed.

Inspect the lens block zoom reset sensor (pin qg of CN1301 on
the VC-421 board) when zooming is performed when the zoom
switch is operated and the zoom motor drive circuit (IC1301on
the VC-421 board) when zooming is not performed.

Check whether the flexible board of the lens is broken, and
check whether it is inserted imperfectly. If there is no problem in
the flexible board, inspect the focus/zoom motor drive circuit
(IC1301 on the VC-421 board).

Inspect PITCH angular velocity sensors (SE6302 on the MA-440
board) peripheral circuits.

Inspect YAW angular velocity sensors (SE6301 on the MA-440
board) peripheral circuits.

Inspect the flash memory (IC3101 on the VC-421 board). (Note)

Inspect the EEPROM (IC2602 on the VC-421 board). (Note)

Note: Refer to “7-2. Record of Self-diagnosis check” of “3-5. SERVICE MODE”, ADJ (9-876-924-51).

1-4E

DCR-DVD105/DVD105E/DVD605/DVD605E_L2

1-6. PRECAUTION ON REPLACING THE VC-421 BOARD

Exif Model Data Check

When you replace to the repairing board, the written data of repairing board also might be changed to original setting.
When the data has changed because of board replaceing etc, check the data setting (Exif Model Data) is right. If not, rewrite to the right v alue.

Exif Model Data

Writing Method:

1) Select page: 0, address: 01 and set data: 01.

2) Select page: A, address: B7 to BA, and set the Exif Model Data.

Note: To write in the non-volatile memory (EEPROM), press the PAUSE (Write) button each time to set the data.

3) Select page: 0, address: 01, and set data: 00.

Page

A
A
A
A

Data

DCR-DVD105

31
30
35
00

DCR-DVD605

36
30
35
00

DCR-DVD105E

31
30
35
45

DCR-DVD605E

36
30
35
45

Address

B7
B8
B9

BA

2-1

2. DISSASSEMBLY

DCR-DVD105/DVD105E/DVD605/DVD605E_L2

Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)

NOTE FOR REPAIR

• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.

• When remove a connector, dont’ pull at wire of connector. It is possible that a wire is snapped.

• When installing a connector, dont’ press down at wire of connector.
It is possible that a wire is snapped.

2-2

DCR-DVD105/DVD105E/DVD605/DVD605E_L2

2-1. DISASSEMBLY

2-1-1. OVERALL ASSEMBLY

HELP

HELP

2-5 (#3)

2-7 (#2)

2-6 (#2)

2-4

(Slide the EVF)

2-2

2-1

2-3

2-8

2-9

3-3 (#2)

3-2

3-1

3-4

2 BT Cabinet Block

3 Lens Block

1 Cabinet (R) block

1-1 (#4)

1-11

1-14

1-13

1-12

1-4 (#2)

1-9 (#2)

1-8 (#2)

1-7

(#10)

1-5 (#1)

1-3 (Open the LCD)

1-10

(Slide the cabinet (R) block)

1-2

1-6

EXPLODE VIEW

HARDWARE LIST

2-3

DCR-DVD105/DVD105E/DVD605/DVD605E_L2

2-1-2. CABINET (R) BLOCK-1

CK-154

1 Mic block

2 CK-154 board

1-2 (#9)

1-1

2-5 (#5)

2-6 (#5)

2-7

2-8

2-10

2-2 (#5)

2-3

2-4

2-1

2-9

EXPLODE VIEW

HARDWARE LIST

2-4

DCR-DVD105/DVD105E/DVD605/DVD605E_L2

2-1-3. CABINET (R) BLOCK-2

MA-440

1 MA-440 board

2 LCD block

1-1 (#9)

1-3

1-5

1-6

1-2

(Boss)

1-4 (#3)

2-1 (#5)

2-3 (#9)

2-4 (Boss)

2-2

EXPLODE VIEW

HARDWARE LIST

2-5

DCR-DVD105/DVD105E/DVD605/DVD605E_L2

2-1-4. LCD BLOCK

HELP

PD-267

3-1

3-2

1 Hinge block

3 LCD

2 PD-267 board

1-1 (#5)

1-2 (#2)

1-10 (#2)

1-5

1-3 (Claw)

1-4 (Claw)

1-7

(Claw)

1-8

1-6

A

A

B

B

1-9

2-1

2-2

2-3

2-6

2-7

2-4 (#5)

2-5

(Claw)

EXPLODE VIEW

HARDWARE LIST

2-6

DCR-DVD105/DVD105E/DVD605/DVD605E_L2

2-1-5. MAIN BLOCK-1

VC-421

DD-246

2-2

2-4

3-1

(#3)

3-4 (#5)

3-2 (#5)

3-3 (#5)

3 Cabinet (L) block

1 DD-246 board

2 VC-421 board

1-1 (#3)

1-2

(Connector)

1-3

2-1 (#3)

2-3 (#3)

2-7 (#3)

2-8 (#3)

2-9

2-10

2-11

2-12

2-13

2-14

2-5 (#2)

2-6

US, CND

EXPLODE VIEW

HARDWARE LIST

2-7E

DCR-DVD105/DVD105E/DVD605/DVD605E_L2

2-1-6. MAIN BLOCK-2

JK-298

3-1

1 JK-298 board

3 FP-342 flexible board

2 Optical drive

1-1 (#3)

2-1 (#6)

2-9

2-3 (#6)

2-4 (#7)

2-5

2-2 (Boss)

1-2

2-10

2-11

2-6 (#6)

2-7 (#7)

2-8

EXPLODE VIEW

HARDWARE LIST

HELP

DCR-DVD105/DVD105E/DVD605/DVD605E_L2

HELP

Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.

Fold

Hinge cover (C)

Screw (#1)

Hinge cover (M)

Claw

Hinge assy

Adhesive tape

Adhesive tape

Adhesive tape

1 Fold dotted line parts of the FP-340 flexible board

as shown in figure.

2 Roll the the FP-340 flexible board 1.5 times,

in the direction of arrow

A.

3 Attach two hinge covers as shown in fugure.

A

Fold

Claw

Claw

Claw

Claw

THE METHOD OF ATTACHMENT OF FP-340 FLEXIBLE BOARD

DCR-DVD105/DVD105E/DVD605/DVD605E_L2

Link

Link

3. BLOCK DIAGRAMS

OVERALL BLOCK DIAGRAM (2/5)

OVERALL BLOCK DIAGRAM (1/5) OVERALL BLOCK DIAGRAM (5/5)

POWER BLOCK DIAGRAM (1/3)

OVERALL BLOCK DIAGRAM (3/5)

POWER BLOCK DIAGRAM (2/3)

OVERALL BLOCK DIAGRAM (4/5)

POWER BLOCK DIAGRAM (3/3)

DCR-DVD105/DVD105E/DVD605/DVD605E_L2

3-1. OVERALL BLOCK DIAGRAM (1/5)

3-1 3-2

( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

3. BLOCK DIAGRAMS

CAMERA SIGNAL

PROCESS,

VIDEO/AUDIO DSP,

LENS CONTROL

(5/14)

IC2701

SE6301

SE6302

YAW_AD

PITCH_AD

PITCH SENSOR

YAW SENSOR

PITCH/YAW

SENSOR

AMP

8

12

2

18

19

IC6302

30

TIMING

GENERATOR

(1/14)

IC1201

S/H, AGC,

A/D CONVERTER

(2/14)

IC1101

26, 25, 28, 31,

18, 21, 22, 33

42

16

43

CN6001

CD-600 BOARD FP-333

FLEXIBLE
BOARD

FP-341 FLEXIBLE
BOARD (1/2)

VC-421 BOARD (1/5)

V1 - V4, RG,

H1, H2, VSHT

V1 - V4, RG,

H1, H2, VSHT

7

CCD

IMAGER

IRIS

(SHUTTER)

LENS BLOCK

CCD_OUTCCD_OUT

CCD_OUT

IC6001

1 - 4, 9, 12, 13, 10

CLAMP

Q6001

LED

DRIVE

Q1001

2 - 11

1, 2, 15, 16

23, 19, 21, 22

15

MA-440 BOARD (1/2)

CN6302

(1/2)

16

VST_C_RESET

15

14

NS_LED_K

7

CN1002
(1/2)

1

3

10

2

LENS_TEMP_AD

05

AC9,

Y9, Y6

OVERALL (2/5)

(PAGE 3-3)

1

OVERALL (4/5)

(PAGE 3-7)

3

OVERALL (4/5)

(PAGE 3-7)

4

OVERALL (2/5)

(PAGE 3-3)

5

OVERALL (3/5)

(PAGE 3-5)

2

OVERALL (5/5)

(PAGE 3-9)

8

OVERALL (3/5)

(PAGE 3-5)

11

248, 250, 251 239, 246, 247

268 - 270

3 - 10

279 - 282

264 - 267,
272, 273,

275, 276

224 - 231,

233, 234

116 - 98 137 - 124, 122, 121

141

241
219
220

217

EN0,

DIR0A, DIR0B

EN01,

DIR1A, DIR1B

ZM_RST

FC_RST

DA_STRB

IRIS_PWM, IRIS_COM

IRIS_PWM, IRIS_COM

I_HALL_AD

TG_FLD TG_FLD

I_HALL_AD

238

237

ZOOM_VR_AD

P22
P23

IR_ON

A13

R22

Y5

P20

Y18

IR_ON

T2

11 - 8, 3 - 1, 6

CN1201

15

XSYS_RST

OVERALL (3/5)

(PAGE 3-5)

9

XRST_VTR

163

CAM_DD_ON

CAM_DD_ON

XSYS_RST

ZOOM_VR_AD

XSYS_RST

XSYS_RST

216

222

236

159, 158, 156, 154, 162

D6302

(NIGHTSHOT)

47, 48, 46

35, 38, 37, 39

AD0 - AD9

AD0 - AD9

AD0 - AD9

D0 - D9

CAMERA
CONTROL

(4/14)

IC2601

(1/2)

F2

157

SYS_V

164

M22

SYS_V

LINEOUT_V

D14

F4

AB19

D13

XRST_VTR

11 - 8, 3 - 1, 6

ED0 - ED7

ADATAIN0
ADATAOUT0
HYI_PLL27IN

MPLCK27

252 - 261

CAM_SO, CAM_SCK

CAM_SI, CAM_SO,
CAM_SCK,
CAM_CS, CAM_VD

CAM_SI, CAM_SO,
CAM_SCK, CAM_CS

CAM_SI, CAM_SO, CAM_SCK, CAM_CS, CAM_VD

EN0,
DIR0A, DIR0B

EN01,
DIR1A, DIR1B

ZM_RST

FC_RST

AB11, Y11,

AB10, C22, A7

A1_CNM - A19_CNM

D0_CNM - D15_CNM

301
298
284
304

119

87

85

82
83

XNS_SW

LENS_TEMP_AD

XNS_SW

CH_SO, CH_SCK, CH_CS

CH_SO, CH_SCK, CH_CS

LINEOUT_V

SYS_V

LINEOUT_V

B8

A9

OVERALL (2/5)

(PAGE 3-3)

10

SPDL_FG

SPDL_FG
OSC1

DSCK_CNM

53
60

IC_2701_Y_OUT
IC_2701_C_OUT

DATA_TO_SFD

89

DATA_FROM_SFD

40
39

PANEL_R

PANEL_G

45

PANEL_B

92

PANEL_XHD

93

PANEL_XVD

161

LINEIN_VD

149

MCXCS_IC_2701

152

BB_SI

151

BB_SO

150

XBB_SCK

144

CNMXCS_IC_2701

147

JAIRQ

SFD_BCK

SFD_LRCK

SFD_FCK

91

KASYAON

A : VIDEO SIGNAL

A : AUDIO SIGNAL

OVERALL (4/5)

(PAGE 3-8)

6

RYO0_DEHD, RYO1_DEVD,

RYO2_DEFLD

RCO0_EDHD, RCO1_EDVD,

RCO2_EDFLD, RCO3_FRMREF

RYI0_DE0 - RYI3_DE3
RCI0_DE4 - RCI3_DE7

F1

AB13

AC14
AB14

1

6

5
2

32K EEPROM

(4/14)

IC2602

EEP_SI

EEP_SO

EEP_SCK
XCS_EEP

X2601
20MHz

D1

C1

40
11

34

44
45

41
48
36

CLPDM_TG, PBLK_TG,

XSHP, XSHD

SYSCK VCK

20

221

CLPOB

XRST_RST

Q1201

9

ADCK27

46

CKCONT2

TG_HD
TG_VD

ZSG1

ZV1

TG_ID

VGAT

VCK
TG_HD
TG_VD
ZSG1
ZV1
TG_ID
VGAT

IC3701

EVR

(D/A CONVERTER)

(3/14)

3
2
1 8

6, 7

Y16, AC17

H

M

IRIS

METER

M

FOCUS
SENSOR

ZOOM

SENSOR

FOCUS

MOTOR

ZOOM
MOTOR

M

CN1301

12

8

9

4 - 124 - 21

19

LENS TEMP

SENSOR

IRIS

DRIVE

Q1301

HALL GAIN

CONTROL

Q1303

NIGHTSHOT

PLUS

(3/14)

IRIS DRIVE

I_DRIVE (-)

I_BIAS (-)

6

I_BIAS (+)

I_HALL (-)

7

I_HALL (+)

FC_A, FC_XA,
FC_B, FC_XB

ZM_A, ZM_XA,

ZM_XB, ZM_B

FC_SENS_OUT

15

ZM_SENS_OUT

16

THERMO_OUT

17

NightShot_Vcc

HALL GAIN

IC1302

(3/14)

IC1301

FOCUS
MOTOR
DRIVE

ZOOM
MOTOR
DRIVE

5, 19, 17, 7 2, 23, 4, 21

14, 16, 13, 15 10, 12, 9, 11

8

14

HALL AMP

5 7

6

12

10

HALL BIAS

1

2

4

X1201

36MHz

5

XTAL AMP

A_2.8V

HALL VRefHALL REG

IC1303
(3/14)

FREQ_AMPOUT

75

3

1

DCR-DVD105/DVD105E/DVD605/DVD605E_L2

3-3 3-4

3-2. OVERALL BLOCK DIAGRAM (2/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

A : VIDEO SIGNAL

A : AUDIO SIGNAL

A : VIDEO/AUDIO SIGNAL

A : VIDEO/AUDIO/SERVO SIGNAL

A : SERVO SIGNAL

DVD CODEC,

USB I/F

(6/14)

IC3001

(1/2)

DVD DSP

(8/14)

IC4101

CN1017

(FOR CHECK)CPC

DVD DRIVE CONTROL

(10/14)

IC4201

(1/2)

RF PROCESS

(9/14)

IC4001

DVD MECHA

DRIVE

(11/14)

IC4302

16M FLASH

(10/14)

IC4202

64M SDRAM

(8/14)

IC4102

LD

DRIVE

PD IC

FPD IC

LASER
DIODE

VC-421 BOARD (2/5)

DVD MECHANISM DECK

(DDX-C1002)

05

OVERALL (1/5)

(PAGE 3-2)

1

M4C7

AA21
AB21
AH23
AB20

V2

E10

D10

E11

1

6

2

5

AA22

Y22

ED0 - ED7

RYO0_DEHD, RYO1_DEVD,

RYO2_DEFLD

RCO0_EDHD, RCO1_EDVD,

RCO2_EDFLD, RCO3_FRMREF

RYI0_DE0 - RYI3_DE3
RCI0_DE4 - RCI3_DE7

ATA_A0 - ATA_A2

ADATAIN0

ADATAOUT0

HYI_PLL27IN

MPLCK27

H17, G14

A9, B9

L6, L7

B6, A7

A1_CNM - A19_CNM

A1_CNM - A23_CNM

D0_CNM - D15_CNM

ATA_D0 - ATA_D15

D0_CNM - D15_CNM

RFOP, RFON

FEO
TEO

VRCK

LVL

WBO

HDO

FLGA

AH20,
AE18,
AE19

D17,
B17,
E17

T10,

P10,

P11

45, 44,

48, 1

AD18,
AD17,
AB19,
AB18

AB9,

AD6 - AD9,

AE5 - AE9,
AG4 - AG10,
AH4 - AH9,

AA18, AE20,
AD20, AG20,
AB17, AG21,
AD19, AE22

AB15, AE17,
AA14, AB16,
AG17, AH19,
AA15, AG19

M13 - M15,
N15, N16,

P15, P16, R17

P14, R14, R15,

T14, T15,
U14 - U16

K16, L16, L17,

M15 - M17, N15 -N17,

P15 - P17, R10, R15 -R17

T8, T9, T15, U9, U10

R2 -R7,
T3 -T7,
U3 - U7

B10, A11,

C11, A9

G10, D11,

B11, U5

P4 - P7,
R4 - R7,
T3 -T7,

U3, U5, U7

A8 - A12,

B8 - B10

A13, A14,

B13 - B16,
D13 - D16,
E13 - E16,

G13, G14

AB11 - AB13,
AD10 - AD13,
AE11 - AE13,
AG11 - AG13,
AH11 - AH13

DSCK_CNM

SFD_FCK

U2

BEEP MELODY

MELODY_ENV

AC5

SFD_BCK

AD22

C1

AA20

SFD_LRCK

DSCK_CNM

12

5

10 9 8 7

1

16

17

14

15

2, 3

17, 19

27, 26

2

AD16
P5

CNMXCS_IC_2701

JAIRQ

Q4001,
Q4002

GAIN

CONTROL

LDD_W2DIS,

LDD_W1DIS

ENBL

CN4001

LDD-OSCEN

LDD_RSET

LDD_W2SET

LDD_W1SET

LDD_W3SET

LDOR

LDOPK

LDOW

LDOEX

LDD_W3DIS

L5D7

K2C3

SCB
SCD

WRTON

K1E5

HFQON

G15

EFMOFP

EFMPK, EFMWP

HDO

WBO

TEST_TEO

TEST_FEO

TEST_RFOP,

TEST_RFON

H16

J1

M11

F4

E14

FOO

17

E10

B4

TRO

14

C11

SKW

10

D15

FMO, FMOS

XMUTE1

MUTEO

FG

FG

HE_A0 - HE_A20 HE_A1 - HE_A20

HE_A0

- HE_A7

HE_D0 - HE_D15

HE_D0 - HE_D15

TXD_TO_IC_4201,

RXD_TO_IC_4201,

SCK_TO_IC_4201,
XCS_TO_IC_4201

SBD0 - SBD15

SBA0 - SBA13

128M SDRAM

(7/14)

IC3103

64K EEPROM

(6/14)

IC3003

SDDT0 - SDDT31

SDADR0 - SDADR11

256M SDRAM

(7/14)

IC3102

BSDDT0 - BSDDT15

BSDADR0 - BSDADR12

HE_D0 - HE_D7

DMO

4

2 28 18

H15B11A10

2

1

4

F2

H16

D3 C2

30

B11

L4A8

F11

E11

E12

D11

50

FPDIC_OUT

D4001

C12

H2

30

PDIC_GAIN

WRTON

PDHG

A - H

RF+, RF-

FOCUS

COIL

TRACKING

COIL

TILT
COIL

M901

SLED MOTOR

M902

SPINDLE MOTOR

M1C5
M2D5

ANMON

APCRSP
APCWSP

ROPCS

H11D11

K11F14
K12F15

READSP

L12F16
M12

J12G16

RFS

RFRP

RFZI

L9C9
M6D8
M5E8

F2

D14

CEO

ROPC

FSAC

M3E7

L3C6

H1C2

25 - 18

26, 25

37 - 34

FCS+, FCS-

24, 23

41 - 38

TRK+, TRK-

20, 19

45 - 42

TLT+, TLT-

8, 6

SHOCK

SENSOR AMP

(8/14)

SHOCK

SENSOR

SE4401

FLGB

EEP_TXD3
EEP_RXD3
EEP_SCK3
XCS_EEP3

IC4401

10

E15

MODULATOR

Q3001, 3002

2, 3

D10, E11

8, 9, 7, 6

SLED1 - SLED4

CN1009

35, 36, 38

3 - 5

U, V, W

COM

MM

MM

6

LDD_OSCMOD

LD_ON

11

TEMP

31

SLEEP_SW

RF_RST_X

FSAC

FSAC

LD_ON

B9

RF_RST_X

D9

DMO_CPU

DMO_SEL

E1

PDHG

E2 A6

C13

LDD_OSCMOD

TEMP

SLEEP_SW

DSP_RST_X

N3

T2

XATA_RESET

D20

A8

XIC_4201_RESET

XIC_4201
_RESET

SPDL_FG

OVERALL (5/5)

(PAGE 3-9)

15

BATT_IN

J1

SWITCH
(11/14)

IC4301

A13

A12

X4101

22.579MHz

OVERALL (5/5)

(PAGE 3-9)

14

OVERALL (1/5)

(PAGE 3-2)

10

OVERALL (1/5)

(PAGE 3-2)

5

OVERALL (4/5)

(PAGE 3-7)

13

X3001
12MHz

A22

A21

B4

OVERALL (5/5)

(PAGE 3-9)

30

64M FLASH

(7/14)

IC3101

B5

XSYS_RST

DCR-DVD105/DVD105E/DVD605/DVD605E_L2

3-3. OVERALL BLOCK DIAGRAM (3/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

3-5 3-6

A : VIDEO SIGNAL

LCD9002

COLOR

EVF UNIT

SWITCHING

Q6501, 6502

BACKLIGHT

DRIVE

Q6503 - 6506

VC-421 BOARD (3/5)

05

FP-343
FLEXIBLE
BOARD (1/2)

LB-116 BOARD

D302

(BACKLIGHT)

15
14
13

17

7

3 - 6, 8 - 12, 16

5, 9 - 13, 15 - 18

5 - 7, 9, 10, 12 - 15, 20

D6503 - 6505
(BACKLIGHT)

OVERALL (1/5)

(PAGE 3-2)

2

PANEL_R
PANEL_G
PANEL_B

PANEL_XHD

34
33
32

48

1

3

PANEL_XVD

VR
VG
VB

20
21
22

26

10

6 -9, 12, 14,

16, 17, 24, 30

COM_EVF

XSTBY_E

HCK1, HCK2,
HST, PCG,
EN, VCK,VST,
WIDE, VP, REF

EVF_VR

CN5102

EVF_VG
EVF_VB

EVF_COM_CS

EVF_STB

20

31

EXTDA

LED_K

50

COM

45

XSTBY

44

DWN

47

D24

D6

A27
B27

H7
V4

G9
H8

G7

E4

B24

28

18
11

5

COM_PANEL

XSTBY_P

DWN

RGT

RGT

COM

XSTBY

DWN
RGT

EVF_HCK1, EVF_HCK2,

EVF_HST, EVF_PCG,

EVF_EN, EVF_VCK,
EVF_VST, EVF_BLK,
EVF_PSIG, EVF_REF

6
7
8

4

14

3, 4, 6, 9 - 14, 20

3, 4, 6, 9 - 14, 20

32, 38 - 43, 46, 48, 49

17, 23 - 28, 31, 33, 34

6 - 9, 11 - 13, 20 - 22

VR

CN301

VG
VB

COM COM

CS

STB

HCK1, HCK2,

HST, PCG, EN,

VCK, VST, BLK,

PSIG, REF

HCK1, HCK2,

HST, PCG, EN,

VCK, VST,

WIDE, PSIG, REF

HCK1, HCK2, HST,

PCG, EN, VCK,

VST, WIDE, PSIG, REF

COM COM

CS

XSTBY

DWN
RGT

TP_BOT

CN6504

CN6502

CN6503

TP_TOP

TP_L
TP_R

2ND_ZOOM (W)

2ND_S/S_SW

2ND_ZOOM (T)

HCK1, HCK2, HST,

PCG, EN, VCK,

VST, WIDE, PSIG, REF

1

17
18
16

21

11

CN302

19

21
22
23

R

CN5101

(1/2)

CN6404

CN6402

CN6401 (1/2) CN6505CN6506

G
B

R
G
B

R
G
B

CK-154 BOARD (1/2)

FP-377 FLEXIBLE BOARD

FP-346 FLEXIBLE BOARD

CONTROL KEY BLOCK
(SB9000)

2

7
8
5

31
30
29

FP-340
FLEXIBLE
BOARD

35

30
29
32

8
9

10

PD-267 BOARD

2

25

KEY_AD1 KEY_AD1

KEY_AD3_V

KEY_AD3_B

27

7

KEY_AD3

45

2

FRONT_XRESET

50

11

XBATT_VIEW

FRONT_XRESET

XBATT_VIEW

41

12

3

4

25 3

4

5

18

PANEL_BL_ON PANEL_BL_ON

34 5 32

35

TP_SEL1

D5

TP_SEL_2

TP_SEL1

TP_Y

TP_X

17 20 17

37

EXTDA EXTDA

15 22 15

7
8
5

29
28
27

24

14
19

2

23

18

16

192118

16

5

3

PANEL_REVERSE

3
4

6

2

4
5
3

36

TP_X

34

TP_Y

TP_SEL_1

TP_X
TP_Y

43

XCS_EVF

BB_SI
BB_SO
XBB_SCK
XCS_EVF

PANEL_BL_ON

EVF_BL_ON

42

BB_SI

45

BB_SO

44

XBB_SCK

OVERALL (4/5)

(PAGE 3-8)

21

DS/HI CONTROL

(6/7)

IC3001

(2/2)

3 1

BACKLIGHT

CONTROL

IC6501

LCD/EVF DRIVE

(13/14)

IC5101

2.5INCH
COLOR

LCD UNIT

LCD9001

TOUCH PANEL

SWITCHING

Q3004

S3771

PLAY/EDIT

S3773

BACK LIGHT

S003

START/STOP

S002

T

S001

W

S6405

EASY

S6404
PANEL

OPEN/CLOSE

S6403
DISP/

BATT INFO

S6402

RESET

S3461

PANEL

REVERSE

EVF BACKLIGHT

DRIVE

1 3

EVF BACKLIGHT

CONTROL

(13/14)

IC5102

Q5103

XRST_VTR XRST_VTR

OVERALL (4/5)

(PAGE 3-8)

22

OVERALL (1/5)

(PAGE 3-2)

11

OVERALL (1/5)

(PAGE 3-2)

9

HI_SO
HI_SI
XHI_SCK
XCS_IC_2601

CAM_DD_ON

IR_ON

CAM_DD_ON

P4

SYS_V

OVERALL (5/5)

(PAGE 3-9)

24

B26

A12

B25

H11
H9

G11
H10

FRONT_TXD0
FRONT_RXD0
FRONT_SCK0

XFUPSTAT

KEY_AD0
KEY_AD2

FRONT_CS

OVERALL (5/5)

(PAGE 3-9)

23

AC2

XCNM_RESET

D1

XHIDSCON_MAD

N4

OSD_V