Sony DVP-S330 Service Manual
DVP-S330/S530D/S550D/S705D
RMT-D108A/D109A/D111A/D111E
SERVICE MANUAL
Photo: DVP-S330
SPECIFICATIONS
CD/DVD player
Laser Semiconductor laser
Signal format system NTSC
Audio characteristics
Frequency response DVD (PCM 96 kHz): 2 Hz to 44 kHz
(±1 dB)*
DVD (PCM 48 kHz): 2 Hz to 22 kHz
(±0.5 dB)
CD: 2 Hz to 20 kHz (±0.5 dB)
Signal-to-noise ratio More than 110 dB (LINE OUT (AUDIO 1,
2) connectors only)
Harmonic distortion Less than 0.0025%
Dynamic range More than 100 dB (DVD)
More than 97 dB (CD)
Wow and flutter Less than detected value
(±0.001% W PEAK)
Outputs and inputs
Jack Output Load impedance
type level
LINE OUT Phono 2 Vrms Over 10 kilohms
(AUDIO 1, 2) jacks (at 50 kilohms)
DIGITAL OUT Optical –18 dBm Wave length: 660 nm
(OPTICAL) output
connector
DIGITAL OUT Phono 0.5 Vp-p 75 ohms terminated
(COAXIAL) jack
LINE OUT Phono 1.0 Vp-p 75 ohms,
(VIDEO 1, 2) jacks sync negative
S VIDEO OUT 4-pin Y: 1.0 Vp-p 75 ohms,
(1, 2) mini DIN sync negative
C: 0.286 Vp-p 75 ohms terminated
COMPONENT phono Y: 1.0 Vp-p 75 ohms,
VIDEO OUT jacks sync negative
(Y, PB/B-Y, PB/B-Y,
PR/R-Y) PR/R-Y:
(EXCEPT S330) 0.7 Vp-p 75 ohms
PHONES Phone 12 mW 32 ohms
(EXCEPT S330) jack
5.1CH Phono 2 Vrms Over 10 kilohms
OUTPUT jacks (at 50 kilohms)
(EXCEPT S330)
US Model
DVP-S330/S530D/S550D
Canadian Model
DVP-S330/S530D/S550D
E Model
DVP-S530D
Hong K ong Model
DVP-S705D
Singapore Model
DVP-S705D
General
Power requirements 120 V AC, 60 Hz
Power consumption 14 W (S330)
16 W (EXCEPT S330)
Dimensions (approx.) 430 × 95 × 305 mm
(17 × 33/4 × 12 in.) (w/h/d)
incl. projecting parts
Mass (approx.) 3.3 kg (7 lb 4 oz) (S330)
3.4 kg (7 lb 8 oz) (EXCEPT S330)
Operating temperature 41°F to 95°F (5°C to 35°C)
Operating humidity 5% to 90%
Supplied accessories
• Audio/Video/S-link connecting cord (1) (US, Canadian)
• Audio/Video connecting cord (1) (E, Hong Kong, Singapore)
• S video cable (1)
• Remote commander (remote) RMT-D108A (1) (S530D)
• Remote commander (remote) RMT-D109A (1) (S330)
• Remote commander (remote) RMT-D111A (1) (S550D)
• Remote commander (remote) RMT-D111E (1) (S705D)
• Size AA (R6) batteries (2)
* The signals from LINE OUT (AUDIO 1, 2) connectors and 5.1 ch L, R
connectors (except S330) are measured. When you play the PCM sound
tracks with 96 kHz sampling frequency, the output signals from the
DIGITAL OUT (OPTICAL, COAXIAL) are converted to 48 kHz
(sampling frequency).
Design and specifications are subject to change without notice.
CD/DVD PLAYER
MICROFILM
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer:
1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder
splashes and bridges.
2. Check the interboard wiring to ensure that no wires are
“pinched” or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them
out to the customer and recommend their replacement.
4. Look for parts which, though functioning, show obvious signs
of deterioration. Point them out to the customer and recommend their replacement.
5. Check the line cord for cracks and abrasion. Recommend the
replacement of any such line cord to the customer.
6. Check the B+ voltage to see it is at the values specified.
7. Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
To Exposed Metal
Parts on Set
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground
and from all exposed metal parts to any exposed metal part having
a return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT -540A. Follow the manufacturers' instructions to use these
instruments.
2. A battery-operated A C milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indica-
tion is 0.75V, so analog meters must have an accurate low-
voltage scale. The Simpson 250 and Sanwa SH-63T rd are e x-
amples of a passive VOM that is suitable. Nearly all battery
operated digital multimeters that have a 2V A C range ar e suit-
able. (See Fig. A)
0.15 µF
1.5 k
Ω
Earth Ground
AC
Voltmeter
(0.75 V)
Fig. A Using AC voltmeter to check AC leakage
WARNING!!
WHEN SERVICING, DO NO T APPR O A CH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION,
BE SURE TO OBSERVE FROM A DISTANCE OF
MORE THAN 25 cm FROM THE SURFACE OF THE
OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
CAUTION:
The use of optical instrument with this product will increase eye
hazard.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation exposure.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED
LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS P AR UNE MARQUE !
SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE
DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ
DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES
NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
– 2 –
TABLE OF CONTENTS
Section Title Page Section Title Page
Service Note ............................................................................ 4
1. GENERAL
This Player Can Play the Following Discs .................... 1-1
Getting Started .............................................................. 1-1
Playing Discs ................................................................. 1-3
Using Various Functions with the Control Menu........... 1-5
Settings and Adjustments ............................................. 1-11
Additional Information ................................................... 1-15
2. DISASSEMBLY
2-1. Case Removal ............................................................... 2-1
2-2. MB-82/85 Board Removal ............................................. 2-1
2-3. AU-208/212 Board Removal
(S330/S530D/S550D) ................................................... 2-1
2-4. AU-210 Board Removal (S705D).................................. 2-1
2-5. Power Block Removal ................................................... 2-2
2-6. Tray Cover Removal ...................................................... 2-2
2-7. Front Panel Removal..................................................... 2-2
2-8. Mechanism Deck Removal............................................ 2-2
2-9. Tray Removal ................................................................. 2-3
2-10. Optical Pick-up Removal ............................................... 2-3
2-11. Belt, Loading Motor (M001),
MS-29/TK-51 Board Removal ....................................... 2-3
2-12. Internal View.................................................................. 2-4
2-13. Circuit Boards Location................................................. 2-5
3. BLOCK DIAGRAMS
3-1. Overall Block Diagram .................................................. 3-1
3-2. RF/Servo Block Diagram .............................................. 3-3
3-3. Signal Process/Video Block Diagram ........................... 3-5
3-4. System Control Block Diagram ..................................... 3-7
3-5. Audio (1) Block Diagram ............................................... 3-9
3-6. Audio (2) Block Diagram ............................................... 3-11
3-7. Audio (3) Block Diagram ............................................... 3-13
3-8. Interface Control Block Diagram................................... 3-15
3-9. Power Block Diagram .................................................... 3-17
4. PRINTED WIRING BOARDS AND SCHEMATIC
DIAGRAMS
4-1. Frame Schematic Diagram ........................................... 4-3
4-2. Printed Wiring Boards and Schematic Diagrams ......... 4-9
TK-51 (RF/SERVO) Printed Wiring Board.................... 4-9
TK-51 (RF/SERVO) Schematic Diagram...................... 4-13
MS-29 (LOADING) Printed Wiring Board and
Schematic Diagram ....................................................... 4-15
MB-82/85 (SIGNAL PROCESS)
Printed Wiring Board ..................................................... 4-17
MB-82/85 (AV DECODER) Schematic Diagram........... 4-21
MB-82/85 (SDRAM) Schematic Diagram ..................... 4-23
MB-82/85 (SERVO DSP) Schematic Diagram ............. 4-25
MB-82/85 (DRIVE) Schematic Diagram ....................... 4-27
MB-82/85 (ARP) Schematic Diagram ........................... 4-29
MB-82/85 (SYSTEM CONTROL)
Schematic Diagram....................................................... 4-31
MB-82/85 (HGA) Schematic Diagram........................... 4-33
MB-82/85 (CLOCK GENERATOR, AUDIO DSP,
V EQ/NR) Schematic Diagram...................................... 4-35
MB-82/85 (DAC) Schematic Diagram........................... 4-37
MB-82/85 (BIAS) Schematic Diagram .......................... 4-39
AU-208 (AUDIO, VIDEO BUFFER)
Printed Wiring Board ..................................................... 4-41
AU-208 (AUDIO, VIDEO BUFFER)
Schematic Diagram....................................................... 4-43
AU-210 (AUDIO, VIDEO BUFFER)
Printed Wiring Board ..................................................... 4-45
AU-210 (AUDIO) Schematic Diagram .......................... 4-49
AU-210 (VIDEO BUFFER) Schematic Diagram ........... 4-51
AU-212 (AUDIO, VIDEO BUFFER)
Printed Wiring Board ..................................................... 4-53
AU-212 (AUDIO) Schematic Diagram .......................... 4-55
AU-212 (VIDEO BUFFER) Schematic Diagram........... 4-57
FL-97/101 (FUNCTION SWITCH, IF CON)
Printed Wiring Board ..................................................... 4-59
FL-99 (FUNCTION SWITCH, IF CON)
Printed Wiring Board ..................................................... 4-61
FL-97/99/101 (FUNCTION SWITCH)
Schematic Diagram....................................................... 4-65
FL-97/99/101 (IF CON) Schematic Diagram ................ 4-67
SW-315/317 (SURROUND SWITCH), FR-146/148/150
(IR/POWER SWITCH) Printed Wiring Boards.............. 4-69
SW-315/317 (SURROUND SWITCH), FR-146/148/150
(IR/POWER SWITCH) Schematic Diagram ................. 4-71
HP-109/111 (HEADPHONE) Printed Wiring Boards
and Schematic Diagram................................................ 4-73
RY-12 (RELAY) Pr inted Wiring Board and
Schematic Diagram....................................................... 4-75
HS-030SF/030SH (SWITCHING REGULATOR)
Printed Wiring Board ..................................................... 4-77
HS-030SF/030SH (SWITCHING REGULATOR)
Schematic Diagram....................................................... 4-79
SRV902UC (SWITCHING REGULATOR)
Printed Wiring Board ..................................................... 4-81
SRV902UC (SWITCHING REGULATOR)
Schematic Diagram....................................................... 4-83
5. IC PIN FUNCTION DESCRIPTION
5-1. System Control Pin Function
(MB-82/85 Board IC202) ............................................... 5-1
6. TEST MODE
6-1. General Description ...................................................... 6-1
6-2. Starting T est Mode ........................................................ 6-1
6-3. Syscon Diagnosis .......................................................... 6-1
6-4. Drive Auto Adjustment .................................................. 6-5
6-5. Drive Manual Operation ................................................ 6-7
6-6. Mecha Aging ................................................................. 6-9
6-7. Emergency History ........................................................ 6-9
6-8. Version Information ....................................................... 6-10
6-9. Video Level Adjustment ................................................ 6-10
7. ELECTRICAL ADJUSTMENTS
7-1. Power Supply Adjustment ............................................. 7-1
1. Power Supply Check
(HS-030SF/030SH BOARD, SRV902UC BOARD) ...... 7-1
2. +3.3 V Adjustment (SRV902UC BOARD)..................... 7-1
7-2. Adjustment of Video System ......................................... 7-2
1. Video Level Adjustment (MB-82/85 BOARD) ............... 7-2
2. S-terminal Output Check (MB-82/85 BOARD) ............. 7-2
3. Checking Component Video Output B-Y
(MB-82/85 BOARD) ...................................................... 7-2
4. Checking Component Video Output R-Y
(MB-82/85 BOARD) ...................................................... 7-2
5. Checking Component Video Output Y
(MB-82/85 BOARD) ...................................................... 7-3
6. Checking S Video Output S-C (MB-82/85 BOARD) ..... 7-3
7-3. Adjustment Related Parts Arrangement ....................... 7-4
8. REPAIR PARTS LIST
8-1. Exploded Views ............................................................. 8-1
8-1-1. Case Assembly (S330/S530D/S550D).................... 8-1
8-1-2. Case Assembly (S705D).......................................... 8-2
8-1-3. Front Panel Assembly .............................................. 8-3
8-1-4. Chassis Assembly .................................................... 8-5
8-1-5. Mechanism Deck Assembly..................................... 8-6
8-2. Electrical Parts List........................................................ 8-7
– 3 –
SERVICE NOTE
1. DISASSEMBLY
• This set can be disassembled in the order shown below.
Set
Case
(Page 2-1)
Tray Cover
(Page 2-2)
Front Panel
(Page 2-2)
MB-82/85
Board
(Page 2-1)
Mechanism
Deck
(Page 2-2)
Tray
(Page 2-3)
Optical Pick-up
(Page 2-3)
AU-208 Board
(S330)
(Page 2-1)
TK-51 Board
(Page 2-3)
AU-210 Board
(S705D)
(Page 2-1)
Belt
(Page 2-3)
Loading Motor (M001),
MS-29 Board
(Page 2-3)
AU-212 Board
S530D/S550D
(
(Page 2-1)
Power
)
Block
(Page 2-2)
– 4 –
2. NOTE ON REMOVE THE CASE
1) Remove seven screws. (See Fig. 1)
2) Open the side of case. (See Fig. 1)
3) Remove the case as lift straight. (See Fig. 1)
Case
Two screws
Three screws
4. HOW TO SERVICE MB-82/85 BOARD
1) Remove the case from the set. (Refer to 2-1)
2) Remove the MB-82/85 board. (Refer to 2-2)
3) Set the MB-82/85 board as shown in Fig. 3.
Note: Do not disconnect wiring, except FMA-7/8/9.
MB-82/85 board
Two screws
Fig. 1
3. DISC REMOVAL PROCEDURE
(at POWER OFF)
1) Insert a tapering driver into the aperture of the unit bottom,
and move the lever of chuck cam in the direction of the ar row
A. (See Fig. 2)
2) Draw out the tray in the direction of the arrow B, and remove
a disc. (See Fig. 2)
Lever of chuck cam
Aperture
B
A
Tray
grooves
Fig. 3
Fig. 2
– 5 –
SECTION 1
GENERAL
DVP-S330/S530D/S550D/S705D
This section is extracted from DVP-S550D
instruction manual (3-865-641-11).
1-1
1-2
1-3
1-4
1-5
1-6
1-7
1-8
1-9
1-10
1-11
1-12
1-13
1-14
1-15
1-16 E
1-16
DVP-S330/S530D/S550D/S705D
7 Three screws
(B3)
5 Four screws
(B3)
(S530D/S550D)
6 Four screws
(B3)
2 Connector
(CN401)
(S530D/S550D)
1 Connector
(CN201)
3 Two flat cables
(CN302, 303)
(S530D/S550D)
4 Flat cable
(CN301)
8 AU-208 board (S330)
AU-212 board (S530D/S550D)
SECTION 2
DISASSEMBLY
Note: Follow the disassembly procedure in the numerical order given.
2-1. CASE REMOVAL 2-3. AU-208/212 BOARD REMOVAL
(S330/S530D/S550D)
4 Case
2 Two screws
1 Three screws
3 Two screws
2-2. MB-82/85 BOARD REMOVAL 2-4. AU-210 BOARD REMOVAL (S705D)
5 Flat cable
(CN005)
7 Four screws
(B3)
8 MB-82 board (S705D)
MB-85 board
(S330/S530D/S550D)
5 Three screws
(B3)
1 Connector
(CN407)
2 Connector
(CN401)
3 Two connectors
(CN301, 404)
4 Three flat cables
(CN402, 403, 405)
7 AU-210 board
6 Nine screws
(B3)
2 Two flat cables
(CN002, 003)
1 Connector
(CN011)
6 Flat cable
(CN006)
4 Two flat cables
(CN004, 007)
(S530D/S550D/S705D)
3 Connector
(CN001)
2-1
2-5. POWER BLOCK REMOVAL
2-7. FRONT PANEL REMOVAL
1 Connector
4 Four screws
(B3)
5 Power block
2 Connector
(CN102)
(S705D)
(CN101)
3 Three connectors
(CN201, 202, 203)
4 Screw
(B3)
(S530D/S550D/S705D)
2 Connector
(CN701)
(S530D/S550D/S705D)
5 Two screws
9 Claw
!º Front panel
(B3)
6 Boss
8 Claw
1 Connector
(CN203)
3 Flat cable
(CN006)
7 Boss
2-6. TRAY COVER REMOVAL 2-8. MECHANISM DECK REMOVAL
4 Tray cover
3 Two claws
B
2 Pull the tray in the
direction of the
arrow B.
A
1 Insert a tapering driver into the aperture of the
unit bottom, and move the lever of chuck cam
in the direction of the arrow A.
4 Mechanism deck
1 Connector
(CN001)
3 Screw
(B3)
2 Two flat cables
(CN003, 004)
2-2
2-9. TRAY REMOVAL
2 Two screws
(B2.6 × 4)
1 Belt
9 TK-51 board
8 Claw
7 Claw
6 Flexible board
(CN001)
5 Flexible board
(CN002)
3 Three claws
4 Loading motor (M001),
MS-29 board
2 Chuck ass’y
B
2-11. BELT, LOADING MOTOR (M001),
MS-29/TK-51 BOARD REMOVAL
1 Two screws
(BTP2.6 × 12)
4 Remove the tray in
the direction of the
arrow B.
3 Move the lever of chuck cam
in the direction of the arrow A.
A
2-10. OPTICAL PICK-UP REMOVAL
5 Optical pick-up
4 Three step
3 Remove the base
unit holder in the
direction of the
arrow A.
screws
1 Two flexible board
(CN001, 002)
2 Two claws
2-3
2-12. INTERNAL VIEW
DC motor (loading)
1-541-632-11
Optical pick-up (KHM-220AAA/J1RP)
8-820-081-03
2-4
2-13. CIRCUIT BOARDS LOCATION
Power Block
SRV902UC (S330/S530: US, Canadian/S550D)
HS-030SH (S705D)
HS-030SF (S530D: E)
(SWITCHING REGULATOR)
FR-146 (S330)
FR-148 (S705D)
FR-150 (S530D/S550D)
(IR/POWER SWITCH)
HP-109 (S705D)
HP-111 (S530D/S550D)
(HEADPHONE)
MS-29
(LOADING)
RY-12 (S705D)
(RELAY)
TK-51
(RF/SERVO)
AU-208 (S330)
AU-210 (S705D)
AU-212 (S530D/S550D)
(AUDIO)
SW-315 (S705D)
SW-317 (S530D/S550D)
(SURROUND SWITCH)
FL-97 (S330)
FL-99 (S705D)
FL-101 (S530D/S550D)
(FUNCTION SWITCH)
MB-82 (S705D)
MB-85 (S330/S530D/S550D)
(SIGNAL PROCESS/SERVO)
2-52-5 E
3-1. OVERALL BLOCK DIAGRAM
DVP-S330/S530D/S550D/S705D
SECTION 3
BLOCK DIAGRAMS
BASE UNIT
KHM-220AAA
OPTICAL DEVICE
DVD/CD
FOCUS
TRACKING
TILT
MOTOR
SPINDLE
MOTOR
PDIC
COIL
COIL
MB-82/85 BOARD
(SEE PAGE 4-21~37)
IC304
16M DRAM
TK-51 BOARD
(SEE PAGE 4-13)
SD 0-7
RF
IC001
DVD/CD RF AMP
DIGITAL SERVO
IC801
FOCUS COIL/
TRACKING COIL/
TILT MOTOR
DRIVE
M
M
DVD RF,
CD RF
IC303
ARP2
IC701
SERVO DSP
CDDOUT, CDDATA,
CDBCK, CDLRCK
IC601
HGA
S550D/S705D
IC402, 403
16M SDRAM
S550D/S705D
IC401
AV DECODER
IC202
SYSTEM CONTROL
V EQ/NR
PDO 0-7
Serial BUS
IC502
Parallel BUS
PDI 0-7
SPDIF, ACH12,
ACH34, ACH56,
BCK, LRCK
IC204
1M SRAM
4K EEP ROM
S530D/S550D/S705D
IC201
IC501
AUDIO DSP
IC205
16FLASH
VIDEO V,
VIDEO Y,
VIDEO C
S530D/S550D/S705D
VIDEO G/Y,
VIDEO R/B-Y,
VIDEO B/R-Y
SPDIF
IC902
AUDIO 2CH DAC
S530D/S550D/S705D
AU-208/210/212 BOARD
(SEE PAGE 4-43,49,51,55,57)
VIDEO
BUFFER
VIDEO
BUFFER
AUDIO LT,
AUDIO RT
LPF,
GAIN CONTROL
HEADPHONE
AMP
HP-109/111
BOARD
(SEE PAGE 4-74)
VIDEO 1, 2
S VIDEO 1, 2
COMPONENT
VIDEO
DIGITAL
OUT
AUDIO
OUT1, 2
PHONES
SLED
MOTOR
M001
LOADING
MOTOR
MS-29 BOARD
(SEE PAGE 4-16)
05
M
IC802
SPINDLE/SLED/
LOADING
MOTOR DRIVE
IC602
16M NAND-F
IC905-907
AUDIO 5.1CH DAC
S330/S530D: US, Canadian/S550D
AUDIO L, R
AUDIO LS, RS
AUDIO C, LFE
LPF
5.1CH OUTPUT
M
ND201
FL-97/99/101 BOARD
(SEE PAGE 4-65,67)
S530D/S550D/S705D
SW-315/317 BOARD
(SEE PAGE 4-71)
IC203
IC201
IF CON
SWITCH SWITCH
S-LINK
SWITCH
FR-146/148/150 BOARD
(SEE PAGE 4-71)
–12V
EVER5V
JOG UNIT
+3.3V
+5V
A+12V
M+12V
+3.3V
+5V
+12V
–12V
EVER5V
S705D
RY-12 BOARD
(SEE PAGE 4-76)
HS-030SF/030SH BOARD
(SEE PAGE 4-79)
SRV902UC BOARD
(SEE PAGE 4-83)
AC10V
T901
SW REG
S-LINK
3-1 3-2
DVP-S330/S530D/S550D/S705D
3-2. RF/SERVO BLOCK DIAGRAM
BASE UNIT
KHM-220AAA
OPTICAL DEVICE
DVD/CD
PDIC
DVD/CD
LD MODULE
COIL
TRACKING
COIL
TILT
M
MOTOR
INLIMIT
SENSOR
RF
A-D
E-H
VC
PD
LD
VR
FCSFOCUS
TRK
TIA, TIB
INLIM
TK-51 BOARD
IC0011(DVD play)
200mV/DIV 100ns/DIV
536mVp-p
IC0011(CD play)
500mV/DIV 500ns/DIV
880mVp-p
CN001
7
9
10
16
17
8
11
15
18
13
4
2
LD DRIVE
5
19
20
21
22
CN002
10
ı
13
2
(SEE PAGE 4-13)
Q001
IC001@ª(DVD play)
200mV/DIV 500ms/DIV
IC001
DVD/CD RF AMP
DIGITAL SERVO
RF IP
1 54
9
ı
A-D
12
5
ı
A2-D2
8
13
E-H
ı
16
VC
17
19
PD
20
LD
592mVp-p
SIGO
MIRR
SCLK
SWD
SRD
SDEN
FDCHG
HOLD2
IC001@ª(CD play)
200mV/DIV 20ms/DIV
IC001%¢(DVD play)
500mV/DIV 100ns/DIV
1.5Vp-p
IC001%¢(CD play)
500mV/DIV 500ns/DIV
1.5Vp-p
40
FE
39
TE
29
PI
26
32
TZC
33
VCI
43
ı
46
Q002
27
42
31
DFT
448mVp-p
CN004
17
9
8
7
3
5
6
SSCK, SSWD,
11
SSRD, SSCS
ı
14
15
4
6
7
4
5
15
ı
18
8
RF+
FE
TE
PI
MIRR
TZC
2VC
SSDFCT
SSDFCTI
FCS
TRK
TIA, TIB
INLIM
MB-82/85 BOARD(1/6)
IC001$º(DVD play)
100mV/DIV 50ms/DIV
180mVp-p
IC001#ª(DVD play)
500mV/DIV 50ms/DIV
CN002CN003
2
10
11
12
16
14
2VC
13
5
ı
8
4
15
CN003
12
13
14
15
1
ı
4
11
500mV/DIV 50ms/DIV
1.3Vp-p
(SEE PAGE 4-25,27)
IC001$º(CD play)
860mVp-p
IC001#ª(CD play)
500mV/DIV 200ms/DIV
1.7Vp-p
IC801
FOCUS
13
14
DRIVE
TRACKING
11
12
DRIVE
15
ı
MOTOR
18
DRIVE
IC802
COIL
COIL
TILT
20
23
26
2
3
9
5
6
7
FCD
TRD
TLTA, TLTB
Q801
IC702 (1/2)
3 1
IC803 (1/2)
12
13
IC701^ª(DVD play)
500mV/DIV 50ms/DIV
1.4Vp-p
IC701^ª(CD play)
500mV/DIV 200ms/DIV
1.7Vp-p
14
IC701^•(DVD play)
100mV/DIV 5ms/DIV
IC701^•(CD play)
500mV/DIV 50ms/DIV
FCD
TRD
TLTA,TLTB
SLDA, SLDB,
STVC
TILT MUTE
FGMODE
180mVp-p
860mVp-p
68
ADC1
69
ADC0
67
ADC2
66
ADC3
65
ADC4
21
TRIN
20
TRREF
23
FGIN
41
GIO 5-8
ı
44
38
GIO 11
28
DFCTI
80
DAB 2,3
85
92
DAB 0, 1
97
48
GIO 1, 2
49
7
PWM 0-2
ı
9
46
GIO 4
50
GIO 0
IC701
SERVO DSP
RS
26 108
X2/CLKIN
FG REF
VRBA,
DAB 0-3
GIO 10
HINT
HRD
HWR
HCS
EA 0, 1
HD 0-7
DVD RF
CD RF
SIGNAL PROCESS,
22
74
81
84
93
96
39
128
1
2
3
4
5
117
ı
120
122
125
IC702 (2/2)
7 5
LOCK
MDS0
MDP0
+3.3V
FCSON
XSDPIT
XSDPRD
XSDPWR
XSDPCS
HA0, 1
HD8-15
N27MSDP
XSDPRST
X3VRST
VIDEO
(SEE PAGE 3-5)
SYSTEM
CONTROL
(SEE PAGE 3-7,8)
SPINDLE
8
SPINDLE
M
MOTOR
SLED
M
MOTOR
05
SPM
SLA, SLB
9
4
ı
7
MS-29 BOARD
(SEE PAGE 4-16)
M001
LOADING
M
MOTOR
S001
TRAY SENSOR
S002
CHUCK SENSOR
CN001
13
14
9
12
1
2
4
6
3
ı
SPM
SLA, SLB
LDM
OCSW 1, 2
CKSW1
5
6
7
ı
10
1
2
4
6
3
CN011
OCSW 1, 2
CKSW1
15
MOTOR
16
DRIVE
SLED
11
ı
MOTOR
14
DRIVE
LOADING
17
MOTOR
18
DRIVE
26
20
2
3
5
6
9
23
SLDA, SLDB,
STVC
+3.3V
+5V
IC803 (2/2)
5 7
10
3 1
2.5VC
8
2VC
1.6VC
Q802, 803
GAIN
CONTROL
SPDLSTOP
SPGAIN
XDRV MUTE
LDMM/DMM
LDMP/DMP
OCSW1
OCSW2
CKSW1
3-3 3-4
3-3. SIGNAL PROCESS/VIDEO BLOCK DIAGRAM
DVP-S330/S530D/S550D/S705D
MB-82/85 BOARD(2/6)
(SEE PAGE 4-21,23,29,35,37)
IC303!ª(CD play)
500mV/DIV 200ns/DIV
1.6Vp-p
DVD RF
RF, SERVO
(SEE PAGE 3-4)
SYSTEM
CONTROL
(SEE PAGE 3-7,8)
CD RF
MDS0
MDP0
LOCK
DFCT
NORF
LOCK
FWON
MD2
MUTE
XARPWR
XARPRD
XARPIT
XARPCS
XARPWT
XCS2
XCS3
XRD
XWRH
XAVDIT
XAVDWT
DACK0
DREQ0
DACK1
DREQ1
IC303!¶(DVD play)
500mV/DIV 100ns/DIV
1.6Vp-p
S550D/S705D
IC502
V EQ/NR
IC304
16M DRAM
MA 0-9
MD 00-15
XRAS, XOE
XMWR, XCAS,
IC303
ARP2
A 0-7
148
150-152
SD 0-7
D 0-7
63-68 70 71
97
SD 0-7
98
100
ı
105
SDCK, SDEF,
91
XSHD, XSAK, XSRQ
93
ı
96
CDDOUT, CDDATA,
107
CDBCK, CDLRCK
ı
110
38
ı
43
45
46
47
ı
51
29
ı
32
166
167
193
194
196
198
ı
202
154-157
136-139
159-162
141-144
164-167
RFIN1
RFIN2
MDS0
MDP0
DFCT
NORF
LOCK
FWON
MD2
MUTE
XWR
XRD
XINT
XCS
XWAT
XRST
87
121
XARPRST
33MARP
146 147
MCKI
123
169-172
SCKI
73-76 79-82
17
19
49
52
55
56
58
59
113
111
60
61
83
84
86
DAD 0-11
105-108
110-113
115-118
DT 0-7 I
103 19 36
XAVDRST
RSTIN
256FS30
IC402, 403
16M SDRAM
DDT 0-15
134 135
137 138
140 141
143 144
146 147
149 150
152 153
155 156
CRPCLKIN
ACLKIN
CLKI
160 163
27M30
33M30
YI 0-7
CLK, CKE,
DQML, DQMU,
CS, WE, CAS, RAS
120-123
125 127
129-132
SCLKIN
168-170 172-178 180-187 189-192 2-5 7-10 12-15 205-208
PDO 0-7
PDO 0-7
IC401
AV DECODER
IC401^¡
1,1Vp-p(H)
HAD 0-21 I
YO 0-7
60-6711-18
PDI 0-7
75-78 80-8386-89 91-94
PDI 0-7
IC401^™
816mVp-p(H)
HSYNC
FLD
97 98
31 29
FLDO
HSYNCO
72 73 98 99
FLDO
HSYNCON
IC401%¶
728mVp-p(H)
IC401^∞
1.2Vp-p(H)
HD 0-15
CLK
RST
SDI
CS
SENO
SDOUT
NR-SENO
NR-SDOUT
S530D/
S550D/
S705D
S330
100
93
R/B-Y OUT
B/R-Y OUT
COMP OUT
ACH12O
ACH34O
ACH56O
G/Y OUT
Y OUT
C OUT
LRCKO
BCKO
DO
VREFI
70
58
54
57
65
61
62
21
22
23
25
26
27
RV401
VIDEO
LEVEL
ADJ
IC401%•
1.0Vp-p(H)
X57RST
27M57
IC401%¢
720mVp-p(H)
CN004
CN005
VIDEO G/Y
4
VIDEO R/B-Y
2
VIDEO B/R-Y
6
1
3
5
8
6
VIDEO V
VIDEO Y
VIDEO C
V MUTE
VS
AU-208/212 BOARD(1/3)
AU-210 BOARD(1/2)
(SEE PAGE 4-43,49,51,55,57)
S530D/S550D/S705D
CN405 :S705D
CN303 :S530D/
S550D
4
6
2
IC3214
1.2Vp-p(H)
IC3212
1.1Vp-p(H)
28
26
24
21
23
CN402 :S705D
CN301 :S330/S530D/S550D
Q301, 302 :S705D
Q321, 322 :S330/S530D/S550D
VIDEO BUFFER
2 15
4
7 10
1
VIDEO BUFFER
4 13
2
7 10
1
DC ON/OFF
IC302
:S705D
IC303
:S530D/S550D
IC301
:S705D
:S330/S530D/S550D
IC321
J302 :S705D
J303 :S530D/S550D
Y
COMPONENT
13
IC321!£
2.4 Vp-p(H)
15
J305 :S705D
J306 :S705D
CB/B-Y
VIDEO OUT
CR/R-Y
VIDEO OUT1
VIDEO OUT2
Y
S VIDEO OUT1
C
Y
S VIDEO OUT2
C
J505 :S330/S530D/S550D
INTERFACE
CONTROL
(SEE PAGE 3-16)
05
XARPRST
XAVDRST
X57RST
S550D/S705D
33MARP
256FS30
33M30
27M30
27M57
S550D/S705D
VS
HA 0-21
HD 0-15
V MUTE
HA 0-7
HD 8-15
CDDOUT, CDDATA, CDBCK, CDLRCK
HA 0-21
HD 0-15
S530D/S550D/S705D
S330
ACH12
ACH34
ACH56
LRCK
BCK
SPDIF1
CDDOUT
CDDATA
CDBCK
CDLRCK
S530D/S550D/S705D
AUDIO 1
(SEE PAGE 3-9)
IC3217
860mVp-p(H)
IC3210
1.8mVp-p(H)
IC321!∞
2.0Vp-p(H)
3-5 3-6
DVP-S330/S530D/S550D/S705D
3-4. SYSTEM CONTROL BLOCK DIAGRAM
MB-82/85 BOARD(3/6)
(SEE PAGE 4-31,33,35)
IC204
1M SRAM
IC205
16M FLASH
SIGNAL PROCESS,
VIDEO
(SEE PAGE 3-5)
RF, SERVO
(SEE PAGE 3-4)
AUDIO 2
:S330/S530D/S550D
(SEE PAGE 3-11)
AUDIO 3
:S705D
(SEE PAGE 3-13)
05
HA 0-21
HD 0-15
HA 0, 1
HD 8-15
X3VRST
S330
GAIN1
GAIN2
S530D/S550D/S705D
IC202(™
2.4Vp-p(12.5MHz)
X201
12.5MHz
X001
27MHz
IC0016
4.2Vp-p(27.0MHz)
HA 0-21
HD 0-15
42 44-64
25-39 41
A 01-15
D 16-31
IC001!¢(DVD play)
4.2Vp-p(25.3MHz)
4.7Vp-p(22.5MHz)
IC001!¶
IC001
PLL
MD
ML
XT1
SYSTEM CONTROL
IC001!¢(CDplay)
SCKO3
17
14
SCKO2
12
SCKO1
2
DACK2/PB6/CS1H
3
PB7/DW1
91
X1
92
X0
A22/P66
RAS1/PB4
66 100 99 98
CKSEL
DVD/CD
DVD:5.8Vp-p(36.5MHz)
CD:5.1Vp-p
19
1
6
IC001!™
4.6Vp-p(33.8MHz)
SI1
SIO
SC0
SO1
SI1
SC0
SO1
IC2025
4Vp-p(25.3MHz)
CS0H/PB2
DW0/PB3
1
3 5
IC004
5
2
7
SC1
SC1
PF7/OCPA0/ATG
IC003
IC0042,5,7
4.2Vp-p(26.9MHz)
SO0
76 77 78 79 80 89 14 97
SI0
SO0
IC202
3
6
1
CS0L
XFRRST
RST
7
CS0L
DACK1
DACK0
DREQ1
DREQ0
CS1
CS4
WR0
WR1
RDY
INT1
INT3
CLK
CS2
CS3
INT0
CS0
RD
11
10
22
23
24
19
94
88
83
95
84
85
86
87
IC207
POWER ON
4 5
RESET
7
5
9
8
IC0035,7
DVD:6.2Vp-p(37.0MHz)
CD:5Vp-p(33.6MHz)
XDACS0
XDACS1
S530D/S550D/S705D
384FSDA
384FS01
27M01
S530D/S550D/S705D
256FS30
33MARP
33M30
S550D/S705D
27M57
27M30
N27MSDP
HA 1-16
HD 0-15
+3.3V
CE
WE
CS
XRD
XWRH
XCS2
XCS3
XAVDIT
DACK1
DACK0
DREQ1
DREQ0
AUDIO 1
(SEE PAGE 3-9)
SIGNAL PROCESS,
VIDEO
(SEE PAGE 3-5)
RF, SERVO
(SEE PAGE 3-4)
CS, WE,
OE, UB, LB
SIGNAL PROCESS,
VIDEO
(SEE PAGE 3-5)
SIGNAL PROCESS,
VIDEO
(SEE PAGE 3-5)
HA 1-20
SC0
SO0
SI0
WE, RY/BY,
HD 0-15
IC201
4K EEPROM
4 3
5 8
6 1
SK
DI
DO
MUTE
MD2
NORF
DFCT
FWON
LOCK
XARPRST
XARPIT
XARPWT
XARPWR
XARPRD
XARPCS
XAVDWT
XAVDRST
X57RST
S550D/S705D
N27MHGA
CS
WC
R/B
VS
OE, CE
WE, UB, LB,
RY/BY, OE
112
113
124
125
141
142
145
144
143
157
156
155
135
102
103
104
105
106
107
108
109
110
111
23
24
25
4
3
98
99
72
71
27
53
59
XECS
XEWC
XEBSY
CS1
CS4
HRD
HWRH
HWRL
WAIT
XINT1
XINT3
RST
CPUCK
MUTE
MD2
NORF
DFCT
FWON
LOCK
ARPRST
ARPINT
ARPWT
ARPWR
ARPRD
ARPCS
AVDWT
AVDRST
57RST
VS
MCK
HA 0-5, 17-19
HA 0-5, 17-19
IC601
HGA
HD 8-15
126-133146-154
HD 0-7
NFD 0-7
XIFINT
FCSON
SDPRST
SDPIT
SDPWR
SDPRD
SDPCS
SPDLSTOP
SPGAIN
XDRVMUTE
LDMP/DMP
LDMM/DMM
OCSW1
OCSW2
CKSW1
01IT0
01IT1
01CS
XDACS2
01RST
DACRST
MA MUTE
S550D/S705D
12
ı
19
5
ı
11
56
22
54
114
115
116
117
118
57
94
93
92
91
64
63
88
29
30
28
96
97
31
26
49
FD 0-7
TEST, CLE, ALE,
XWE, XWP,
XCE, XRE, R/B
S530D/S550D/S705D
IC602
16M NAND-F
18
ı
21
I/O 0-7
24
ı
27
2
ı
5
40
ı
43
FCSON
XSDPRST
XSDPIT
XSDPWR
XSDPRD
XSDPCS
SPDLSTOP
SPGAIN
XDRVMUTE
LDMP/DMP
LDMM/DMM
OCSW1
OCSW2
CKSW1
X01INT0
X01INT1
X01CS
XDACS2
XDACS3
X01RST
XDACRST
MA MUTE
SC1
SO1
SI1
CS0L
SC0
SO0
SI0
XFRRST
RF, SERVO
(SEE PAGE 3-4)
AUDIO 1
(SEE PAGE 3-9)
AUDIO 2
:S330/S530D/S550D
(SEE PAGE 3-11)
AUDIO 3
:S705D
(SEE PAGE 3-13)
IC203
BUFFER
12
4A
4Y
2A
2Y
4 6
1A
1Y
1 3
S530D/S550D/S705D
11
SC1
SO1
SI1
XVIFCS
IFSC0
IFSO0
IFSI0
XFRRST
XIFINT
AUDIO 1
(SEE PAGE 3-9)
INTERFACE
CONTROL
(SEE PAGE 3-16)
3-7 3-8
Loading...