Sony DVPNW-50 Owners manual

2-584-978-11(1)

Compact Disc Player

CDP-NW10

DVD Player

DVP-NW50

User’s Manual

 2005 Sony Corporation

WARNING

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving

antenna.

– Increase the separation between the

equipment and receiver.

– Connect the equipment to an outlet on a

circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced

radio/TV technician for help.

CAUTION

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and in particular, specifies that the cable ground shall be connected to the ground system of the building, as close to the point of cable entry as practical.

If you have any questions about this product, you may call; Sony Customer Information Service Center 1-800-222-7669 or http://www.sony.com/

The number below is for the FCC related matters only.

Regulatory Information

Declaration of Conformity

Trade name: SONY Model No.: CDP-NW10/DVP-NW50 Responsible Party: Sony Electronics Inc. Address: 16450 W. Bernardo Dr.

San Diego, CA 92127 U.S.A.

Telephone No.: 858-942-2230 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Important Safety Instruction

1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with dry cloth. 7 Do not block any ventilation openings.

Install in accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such

as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9 Do not defeat the safety purpose of the

polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10Protect the power cord from being

walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11Only use attachments/accessories

specified by the manufacturer.

12 Use only with the cart, stand,

tripod, bracket, or table specified by manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13Unplug this apparatus during lightning

storms or when unused for long periods of time.

14Refer all servicing to qualified service

personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Welcome!

Thank you for purchasing the Sony Custom Integrated AV System. Before operating the unit, please read this manual thoroughly and retain it for future reference.

TABLE OF CONTENTS

About This Manual 5 Notes About the Discs 5 Features 6 Quick Guide to Disc Type 8

Chapter 1 Getting Started

Setting up the System 10

Connecting a TV (DVP-NW50 only) 10 Connecting audio Equipment 10 Selecting a method for using the remote 11

Setting up the Units 11

Setting an IP Address 11 Naming the Unit 12 Setting the time 13 Setting a remote code on the Unit 13 Selecting the time interval for automatic return to the Home Menu 13

Chapter 2 Parts and Controls

Parts and Controls 14

Key operation on the Unit 15 Key operation on the remote 16 Preparing the remote 18 Setting a remote code on the remote 18 Menu operation 18 Menu tree 19

Chapter 3 Playing Discs (CDP-NW10 only)

Playing a CD Disc 20

Various play mode functions (Shuffle play, Repeat play) 21 Searching for a particular point on a disc (Search/Scan) 21

Chapter 4 Playing Discs (DVP-NW50 only)

Playing a CD Disc 22

Various play mode functions (Shuffle play, Repeat play) 23

Playing a DVD/VCD/MP3 Disc 23

Using the DVD´s menu 24 Playing VIDEO CDs with PBC functions (VIDEO CD Ver. 2.0 or higher ) 24 Playing an MP3 audio track 25

Searching for a Scene 25

Searching for a particular point on a disc (Search/Scan) 25 Searching for a title/chapter/track/scene, etc. (Search mode) 25

Using Various Additional Functions 26

Selecting the audio 26 Selecting the subtitles 26 Selecting the angle 26 Parental control (limited playback) 27

Using the Setup Display (DVD Settings) 28

Setting the display (General Setup) 28 Setting the language and playback restriction (Preference) 29

Continue to the next page

TABLE OF CONTENTS (continued)

Chapter 5 Enjoying Radio and Other Component

Listening to the Radio 31

Listening to a preset station 31 Listening to a non-preset station 31

Presetting Radio Stations 33 Naming the Preset Stations 33 Listening to Sound from a Component Connected to LINE IN 34

Chapter 6 Using the System Network

Playing Music on Other Units 35

Playing back music from “NETWORK” 35 Playing back music from “MY MUSIC” 36 Various play mode functions (Shuffle play, Repeat play) 36

Enjoying Music in All Rooms Simultaneously (Party mode) 37

Excluding the Unit from a Party mode (Party Privacy) 37

Talking with Persons in Other Rooms (INTERCOM) 38

Excluding a Unit from INTERCOM (Intercom Privacy) 38 Changing the call sound of the INTERCOM 38

Monitoring Other Rooms (MONITOR) 39

Excluding a Unit from MONITOR (Monitor Privacy) 39

Chapter 7 Setting the Timer

Setting the Alarm 40 Setting the Sleep Timer 41

Chapter 8 Other Functions

Using the Setup Display 42

Selecting the surround mode (DVP-NW50 only) 42 Adjusting the contrast of the front panel display (DIMMER) 43 Presetting the volume when the power is turned on (VOL PRESET) 43 Adjusting the front speaker balance (BALANCE) (CDP-NW10 only) 43

Settings for Speakers (DVP-NW50 only) 44

Selecting a speaker size 44 Setting the speaker distance 45 Setting a speaker level 45 Adjusting the speaker volume – TEST TONE 46 Setting the dynamic range compressor 46

Operating a Sony TV with the Remote 47

Controlling your TV with the remote 47

Chapter 9 Other Information

Precautions 48 Troubleshooting 49 Error Messages 53 Specifications 54 Language Code List 55 Index 56

About This Manual

Notes About the Discs

• Some operations and displays may differ slightly, depending on the model you use.

• “DVD” may be used as a general term for DVD VIDEOs, DVD+RWs/DVD+Rs and DVD-RWs/ DVD-Rs.

• The meaning of the icons used in this manual is described below:

Icon Meaning

Functions available for DVD VIDEOs and DVD+RWs/DVD+Rs or DVD-RWs/ DVD-Rs in video mode.

Functions available for VIDEO CDs (including Super VCDs or CD-Rs/ CD-RWs in video CD format or Super VCD format encoding).

Functions available for music CDs or CD-Rs/CD-RWs in music CD format.

Functions available for DATA CDs (CD-ROMs/CD-Rs/CD-RWs containing MP3* audio tracks).

* MP3 (MPEG1 Audio Layer 3) is a standard format defined by

ISO (International Organization for Standardization)/MPEG which compresses audio data.

To keep the disc clean, handle the disc by its edge. Do not touch the surface.

• Do not expose the disc to direct sunlight or heat sources such as hot air ducts, or leave it in a car parked in direct sunlight as the temperature may rise considerably inside the car.

• After playing, store the disc in its case.

• Clean the disc with a cleaning cloth. Wipe the disc from the center out.

• Do not use solvents such as benzine, thinner, commercially available cleaners, or anti-static spray intended for vinyl LPs.

• If you have printed the disc’s label, dry the label before playing.

5US5

Features

The CDP-NW10/DVP-NW50 (referred to as the Unit in this manual) is a home audio component system based on network connections. A Unit is installed into the wall of a room and connected to other Units using an Ethernet connection (100Base-TX.) The system consists of:

– Up to 12 Units (CDP-NW10 or DVP-NW50) – A personal computer (if necessary) – Audio output components, such as a CD Changer – A monitor or a projector (DVP-NW50) – Two speakers (2CH) (CDP-NW10)/Five speakers

and a sub woofer (5.1CH) (DVP-NW50)

The main features of the Unit are the following:

• Two types of conventional CD player model and a DVD player model with a simple timer clock and 2ch audio input

• The Unit can play back MP3-format audio files stored on a computer via a network (An exclusive application of PC is needed)

• The Unit can play back CDs mounted in other Units via a network

• The Unit can play back the audio contents in all the rooms simultaneously from the following sources (Party mode)

– CDs in any Units – MP3 discs (DVP-NW50 only) and LINE IN in the

lead operating Unit – FM or AM tuner – MP3-format audio files stored on a computer (a

Playlist feature in the Unit is available)

• INTERCOM and MONITOR functions via a network

• 2ch to 5.1ch sound produced from connected speakers for DVP-NW50, or 2ch sound produced from connected speakers for CDP-NW10

Trademarks and Copyrights

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

This Unit incorporates Dolby* Digital and Pro Logic surround and the DTS** Digital Surround System.

* Manufactured under license from Dolby Laboratories.

“Dolby,”“Pro Logic,” and the double-D symbol are trademarks of Dolby Laboratories.

** Manufactured under licence from Digital Theater System,

Inc. “DTS” and “DTS Digital Surround” are registered trademarks of Digital Theater System, Inc.

Gracenote/CDDB

Corporate description

Music recognition technology and related data are provided by GracenoteR. Gracenote is the industry standard in music recognition technology and related content delivery. For more information visit www.gracenote.com.

Proprietary legends

CD and music-related data from Gracenote, Inc., copyright © 2000-2005 Gracenote. Gracenote CDDBR Client Software, copyright 2000-2005 Gracenote. This product and service may practice one or more of the following U.S. Patents: #5,987,525; #6,061,680; #6,154,773, #6,161,132, #6,230,192, #6,230,207, #6,240,459, #6,330,593, and other patents issued or pending. Services supplied and/or device manufactured under license for following Open Globe, Inc. United States Patent 6,304,523.

Gracenote and CDDB are registered trademarks of Gracenote. The Gracenote logo and logotype, and the “Powered by Gracenote” logo are trademarks of Gracenote.

CDP-NW10/DVP-NW50 system network

The diagram below illustrates an entire system network made up of multiple Units. The configuration shown below is for illustrative purposes only. It may differ from an actual system network. Contact your nearest installer for details on making the required connections for the system network.

INTERNET

LIVING ROOM

CDP-NW10

Front Speaker

Router

BEDROOM

CDP-NW10

Hub

DVP-NW50

GUEST ROOMKITCHEN

CDP-NW10

Computer

Front Speaker

Rear Speaker

TV/Projector CD Changer

Center

Speaker

Sub Woofer

Example of a DVP-NW50 system network

Rear Speaker

7US7

Quick Guide to Disc Type

Discs that can be played back on the Unit differ, depending on the model you are using. The kinds of disc that you can use on the Unit are as follows.

CDP-NW10

Format of discs

Music CD

CD-R

CD-RW

Also, the Unit can play CD-Rs/CD-RWs recorded in the following format: – Music CD format – CD Extra format*

* Only a music session can be played back.

The kinds of disc that cannot be played back

– CD-Rs/CD-RWs other than those recorded in the formats listed

above – CD-ROM – Data part of CD-Extras – VIDEO CD – DVD+R/DVD-R/DVD-RW/DVD+RW – DVD-ROM – DVD Audio – MP3 format – Super Audio CD

DVP-NW50

Format of discs

DVD VIDEO

DVD-R

DVD-RW

VIDEO CD

Music CD

CD-R

CD-RW

The “DVD VIDEO” logo, the “DVD-R” and the “DVDRW” logo are trademarks.

Also, the Unit can play CD-Rs/CD-RWs recorded in the following formats: – Music CD format – CD Extra format* – VIDEO CD format – MP3 format conforming to ISO 9660* Level 1/Level 2,

or its extended format, Joliet

* A logical format or files and folder on CD-ROMs, defined by

ISO (International Organization for Standardization)

The kinds of disc that cannot be played back

– CD-Rs/CD-RWs other than those recorded in the formats listed

above – CD-ROM recorded in PHOTO CD format – Data part of CD-Extras – DVD-ROM – DVD Audio – Super Audio CD – DVD VIDEO with a different region code – DVD-R/DVD-RW´s inVR (Video Recording) mode – DVD+R/DVD-R of double layer disc

Example of discs that the Unit cannot play

Region code

The Unit cannot play the following discs:

– A disc that has a non-standard shape (e.g., card, heart) – A disc with paper or stickers on it – A disc that has the adhesive of cellophane tape or a sticker still

left on it.

Note about CD-R/CD-RW/DVD-R/DVD-RW (Video mode)/DVD+R/ DVD+RW

In some cases, CD-R/CD-RW/DVD-R/DVD-RW (Video mode)/DVD+R/DVD+RW cannot be played on the Unit due to the recording quality or physical condition of the disc, or the characteristics of the recording device and authoring software. The disc will not play if it has not been correctly finalized. For more information, see the operating instructions of the recording device. Note that discs created in the Packet Write format cannot be played.

Music discs encoded with copyright protection technologies

This product is designed to play back discs that conform to the Compact Disc (CD) standard. Recently, various music discs encoded with copyright protection technologies are marketed by some record companies. Please be aware that among those discs, there are some that do not conform to the CD standard and may not be playable by this product.

Note on DualDisc

A DualDisc is a two sided disc product which mates DVD recorded material on one side with digital audio material on the other side. However, since the audio material side does not conform to the Compact Disc (CD) standard, playback on this product is not guaranteed.

This Unit is designed and manufactured to respond to the Region Management information that is recorded on a

DVD VIDEO. The region code of this Unit is “1.”

ALL

This Unit will play DVD VIDEO labelled

If you try to play any other DVD VIDEO, the message “wrong region” will appear on the TV screen. Depending on the DVD VIDEO, there may be no region code indication, even though playing the DVD VIDEO is prohibited by area restrictions.

Note on playback operations of DVDs and VIDEO CDs

Some playback operations of DVDs and VIDEO CDs may be intentionally set by software producers. Since this Unit plays DVDs and VIDEO CDs according to the disc contents the software producers designed, some playback features may not be available. Also, refer to the instructions supplied with the DVDs or VIDEO CDs.

9US9

Chapter 1

Setting up the System

Getting Started

This chapter provides you with information how to connect and setup the Unit.

Your system has already been installed by an installer. If you want to change the configuration, the TV or the audio equipment, check the location of the VIDEO out jack, the LINE IN jack, and the IR IN/OUT jack. Contact your nearest installer for details on the connections required by the system.

Connecting a TV (DVP-NW50 only)

Connections between the Unit and each device are made via cables or cords coming through the wall. Connect the VIDEO OUT of the Unit to a TV. Select one of the ways of connection methods shown below, according to the input jack on your TV.

VIDEO cord (not supplied)

VIDEO OUT of Unit

Note

Do not connect a VCR, etc., between your TV and the Unit. If you pass the Unit signals via the VCR, you may not receive a clear image on the TV screen. If your TV has only one video input jack, connect the Unit to this jack.

S VIDEO cord (not supplied)

VIDEO OUT of Unit

VCR

Connect directly

Connecting audio Equipment

Connections between the Unit and each of devices are made via cables or cords coming through the wall. The Unit can input sound from external audio equipment via the audio connectors on the Unit. Connect the OUTPUT jacks (L/R) of the audio equipment to the LINE IN (L/R) jacks of the Unit using the proper audio cords (optional).

Unit CD Changer

LINE IN LINE OUT

Setting up the Units

Selecting a method for using the remote

Connections between the Unit and each device are made via cables or cords coming through the wall. You can operate a component using the remote if the IR IN/OUT terminal of the Unit and the component are connected. For example, if you connect IR IN of the Unit and IR OUT of a TV, you can operate the Unit with the Remote by aiming it at the TV.

1 Press the “V” SELECT on the HOME Menu, then

press the “SETUP” SELECT.

The Setup Menu appears.

2 Press the “V” SELECT repeatedly until “IR ROUTE”

appears on the front panel display.

3 Press the “IR ROUTE” SELECT.

The IR route setup Menu appears.

4 Select a method for using the remote.

The default setting is underlined.

Contact your nearest installer for details on the default setting for each parameters. For details on how to make a selection in the Menu, see page 18.

Setting an IP Address

There are two ways to acquire an IP address. The default setting is underlined.

•

AUTO: You can acquire the IP address

automatically. Normally, select this setting.

• MANUAL: You can set up the IP address manually. Because some knowledge of networking is required to use this setting, we recommend you normally to select “AUTO.”

1 Press the “V” SELECT on the HOME Menu, then

press the “SETUP” SELECT.

The Setup Menu appears.

Chapter 1 Getting Started

Method Operates

EYE The Unit directly from the remote. JACK The Unit through the IR IN jack using signals

from the remote.

Both The Unit directly and through the IR IN

jack using signals from the remote.

2 Press the “V” SELECT repeatedly until “LAN”

appears on the front panel display.

3 Press the “LAN” SELECT.

The LAN setup Menu appears.

4 Press the “IP ADDRESS” SELECT.

The IP address setup Menu appears.

Continue to the next page

Setting up the Units (continued)

Chapter 1 Getting Started

5 Press “AUTO” or “MANUAL” SELECT.

If you select “AUTO,” setting an IP address is completed. If you select “MANUAL,” go to the step 6.

6 Press the A SELECT to set an IP address.

“i” appears, and the first three numbers can be entered.

7 Enter the IP address using numeric buttons on the

remote, then press ENTER.

8 Press the B SELECT to set a Sub-net mask.

“i” appears, and the first three numbers can be entered.

Naming the Unit

You can change the name of each room to something more recognizable and have it displayed on the front panel display.

1 Press the “V” SELECT on the HOME Menu, then

press the “SETUP” SELECT.

The Setup Menu appears.

2 Press the “V” SELECT repeatedly until “NAME”

appears on the front panel display.

3 Press the “NAME” SELECT.

The Room name list appears.

4 Press the “KITCHEN,” “BEDROOM,” “DEN,” or

“PATIO” SELECT that you want to change the name by pressing the corresponding SELECT.

5 If you want to name the room as you like, press

the “EDIT” SELECT.

The Text edit setup Menu appears. Enter the name in the text box using the function SELECT. See the table below for details on the function of each of the buttons.

9 Enter the Sub-net mask using numeric buttons on

the remote, then press ENTER.

Press BACK.

The display returns to the LAN setup Menu.

Press the “DIAGNOSIS” SELECT.

The confirmation display appears. Confirm the following items.

IP Assign

OK IP address is assigned correctly. NG Illegal address has been assigned.

IP Conflict

OK IP address has no conflict. NG Two or more Units are using the same IP

Cable Connect

OK Ethernet cable is inserted correctly. NG Ethernet cable is not inserted correctly.

address.

A Moves the cursor to the left in the text being edited

(Text Edit).

B Changes characters in reverse alphabetical order. C Clears the character on which the cursor is placed

in the text being edited (Text Edit).

D Cancels editing and returns to the Room name list. E Moves the cursor to the right in the text being

edited (Text Edit).

F Changes characters in alphabetical order. G Enters the selected character into the text box. H Stores the name and returns to the Room name list.

Tip

You can input up to eight characters for the name of each room.

Setting the time

You must set the time to make functions available, such as an alarm or a sleep timer. Display the Home Menu as shown below beforehand (see page 18).

1 Press the “V” SELECT on the HOME Menu, then

press the “CLOCK” SELECT.

The Clock Menu appears.

2 Press the “TIME SET” SELECT.

The Time set Menu appears.

Setting a remote code on the Unit

If the supplied remote interferes with an other, set the remote code for this Unit and the remote to one that differs from the other Unit. The defalt remote code setting for the Unit and the supplied remote is CIS2.

1 Press the “V” SELECT on the HOME Menu, then

press the “SETUP” SELECT.

The Setup Menu appears.

2 Press the “V” SELECT repeatedly until “SIRCS”

appears on the front panel display.

3 Press the “SIRCS” SELECT. 4 Press the “CIS2” (or “CIS3”) SELECT.

The remote code is set to the same one used by RM SETUP on the remote.

Note

You cannot operate the Unit using the remote when the remote code of the Unit and the remote are different.

Chapter 1 Getting Started

3 Press the “24H” (or the “12H”) SELECT on the Time

set Menu to select the time display mode.

The time display mode toggles between 24H and 12H as you press the button.

4 Set the hour and minute using the “HOUR” and the

“MIN” SELECT.

5 Press HOME to return to Home Menu.

The time is displayed on the right side of the upper line on the HOME Menu.

Note

The clock is not displayed when the Unit is in the Edit Menu or Party mode.

Selecting the time interval for automatic return to the Home Menu

The front panel display automatically returns to the Home Menu when the selected time has elapsed. The defalt time setting for the Unit is 30 seconds.

1 Press the “V” SELECT on the HOME Menu, then

press the “SETUP” SELECT.

The Setup Menu appears.

2 Press the “V” SELECT repeatedly until “TIME OUT”

appears on the front panel display.

3 Press the “TIME OUT” SELECT. 4 Press the “30sec,” “5sec,” “10sec,” or “No”

SELECT.

Note

If you select “No,” the front panel display does not return to the Home Menu automatically.

Chapter 2

Parts and Controls

This chapter provides you with information on the parts and controls of each component, and information on menu operation.

Parts and Controls

Key operation on the Unit

Chapter 2 Parts and Controls

1 REMOTE SENSOR 2 SPEAKER (for INTERCOM/MONITOR) (page 38, 39)

Receives the sound while INTERCOM or MONITOR is set to ON.

3 X/1 (POWER) (page 20, 22, 23)

Press to turn the power on/off.

4 SELECT (page 18)

Press to select an item on the front panel display, such as menu items, settings, tracks, etc.

5 MODE

Press to jump to the Mode Menu of each function.

6 BACK (page 12, 42)

Press to return to the previous menu or to view the current status of the disc title list or the Preset station list.

7 m/M (SCROLL DOWN/UP)

Press to scroll the LCD menu. When you listen to the radio, you can adjust the frequency by all kinds of tuning.

8 HOME

Press to return to the Home Menu.

9 MUTING (page 20, 22)

Press to mute the speaker output from the Unit, or to cancel muting when it is set to ON.

0 +/– VOLUME (page 38, 39)

Press to adjust the volume of the speaker output from the Unit.

qa OPEN/CLOSE (page 20, 22, 23)

Press to open/close the door on the Unit.

qs MICROPHONE

Picks up the sound while INTERCOM is set to ON.

qd OPERATIONAL BUTTONS (page 20, 22, 23)

N(PLAY): Press to play the selected source X (PAUSE) : Press to pause playback x (STOP) : Press to stop playback ./> : Locates a specific track

qf Display (page 18)

Displays the Home Menu and the Setup Menu, etc. You can operate the Home Menu and the Setup Menu, etc., using any SELECT (4).

Continue to the next page

Chapter 2 Parts and Controls

Parts and Controls (continued)

Key operation on the remote

TV/VIDEO

RM SETUP

1234

5678

ENTER CLEAR

SELECT

MODE BACK

HOME

DOWN

DVD

TOP MENU MENU

ENTER

RETURN DISPLAY TV VOL TV CH AUDIO

MASTER VOL

MUTING

ANGLE

SUBTITLE

DVD SETUP

1 RM SETUP (page 18)

Press to preset the remote code, and switch between CIS2/CIS3.

2 TV/VIDEO (page 47)

Press to switch signals between TV input and Video input for the Sony TV monitor.

3 Numeral buttons

Press to select a number, representing, for example, a desired track of the audio source.

4 SELECT (page 18)

Press to select an item on the front panel display, such as menu items, settings, tracks, etc.

5 MODE

Press to jump to Mode Menu of each function.

6 HOME

Press to return to the Home Menu on the display.

qk ?/1 (page 20, 22, 23)

Press to turn the Unit on/off.

ql TV ?/1 (page 47)

Press to turn the Sony TV on/off.

w; CLEAR

Press to clear a number which you entered.

wa ENTER

Press to set the number you entered using the numeric buttons.

ws BACK (page 12, 42)

Press to return to the previous menu or to view the current status of the disc title list or the Preset station list.

wd m/M (page 21, 25)

Press to locate a portion you want to play within a track of the source.

Chapter 2 Parts and Controls

7 DOWN/UP

Press to scroll the LCD menu. When you listen to the radio, you can adjust the frequency by all kinds of tuning.

8 ./> (page 21, 25)

Press to locate a specific track of the source or to select a preset station.

9 X (PAUSE)

Press to pause the playback of the source.

0 H (PLAY) (page 20, 22, 23)

Press to operate the selected source. H (PLAY) button has a tactile dot.**

qa TOP MENU* (page 24)

Press to display the top menu while using DVP-NW50.

qs G/ F/f /g*

Press to select a DVD setup menu on the TV screen.

qd ENTER*

Press to confirm the selection while using DVP-NW50.

qf RETURN*

Press to return to the specified position defined by DVD or VIDEO CD.

wf x (STOP) (page 20, 22, 23)

Press to stop the current playback.

wg MENU* (page 24)

Press to display a menu while using DVP-NW50.

wh MUTING (page 20, 22)

Press to mute the speaker output from the Unit on/off.

wj MASTER VOL +/–

Press to adjust the volume of the speaker output from the Unit. MASTER VOL + button has a tactile dot.**

wk ANGLE (page 26)*

Press to change the viewing angle.

wl DVD SETUP (page 27, 28, 29, 30)*

Press to display the Setup display on the TV screen.

e; AUDIO (page 26)*

Press to select the language of the sound track.

ea SUBTITLE (page 26)*

Press to display subtitles or turn them on/off.

* Used for operating a DVP-NW50 only ** Use the tactile dot as a reference when operating the system.

qg DISPLAY* (page 26)

Press to display a search menu.

qh TV VOL +/– (page 47)

Press to adjust the Sony TV volume. TV VOL + button has a tactile dot.**

qj TV CH +/– (page 47)

Press to change the Sony TV channel. TV CH + button has a tactile dot.**

Continue to the next page

Parts and Controls (continued)

Chapter 2 Parts and Controls

Preparing the remote

nsert two R06 (size-AA) batteries into the battery compartment with the + and – correctly oriented to the markings. When using the remote, point it at the IR sensor

Notes

• Under normal conditions, the batteries should last for about six

months. When the remote no longer operates the Unit, replace both batteries with new ones.

• Do not leave the remote in an extremely hot or a humid place.

• Do not drop any foreign object into the remote casing,

particularly when replacing the batteries.

• Do not use a new battery with an old one.

• Do not expose the IR sensor to direct sunlight or lighting

equipment. Doing so may cause a malfunction.

• If you do not intend to use the remote for an extended period

of time, remove the batteries to avoid possible damage from battery leakage and corrosion.

on the Unit.

Press the A or B SELECT while “RM SETUP” is being pressed on the remote.

The default setting is CIS2. When you press the A SELECT, remote code is set to CIS2. When you press the B SELECT, remote code is set to CIS3.

Note

You cannot operate the Unit using the remote when the remote code of the Unit and the remote are different.

Menu operation

The Home Menu is displayed on the Unit (A). Using the Home Menu, you can select the sound and make various adjustments to items.

Using any SELECT (B), you can select an item on the front panel display.

When the item is displayed on the left side, press a SELECT on the left side. When the item is displayed on the right side, press a SELECT on the right side.

Setting a remote code on the remote

You can switch the remote code (CIS2 or CIS3) on the remote. If the remote code of the Unit and the remote are different, you cannot use the remote to operate the Unit. Make sure that the remote code of the remote and the Unit is the same. For details on setting a remote code on the Unit, see page 13.

RM SETUP

TV/VIDEO

1234

5678

ENTER CLEAR

SELECT

MODE BACK

HOME

DOWN

For example, when you want to select “DVD,” press the F SELECT. When you want to see items below those currently displayed, press the “H” SELECT. (When there are additional items, “V” is displayed). When you want to see items above those currently displayed, press the “G” SELECT. (When there are additional items, “v” is displayed). For details on the Menu tree, see the next page.

C Press to jump to the Mode Menu of each function. D Press to return to the previous menu. E Press to return to the top menu.

+ 42 hidden pages