Sony DVP-NSSOOV Operating Instructions Manual

3-070-605-11(i)

SACD/DVD Player

Operating Instructions

VIDEO

SUPER AUDIO CD

DVP-NSSOOV

0 2001 Sony Corporation

? Precautions

On safety

. Caution -The use of optical instruments with

this product will increase eye hazard.

l Should any solid object or liquid fall into the

cabinet, unplug the player and have it checked by qualified personnel before operating it any further.

On power sources

l The player is not disconnected from the AC

power source as long as it is connected to the wall outlet, even if the player itself has been turned off.

. If you are not going to use the player for a long

time, be sure to disconnect the player from the wall outlet. To disconnect the AC power cord, grasp the plug itself; never pull the cord.

l Should the AC power cord need to be changed,

have it done at a qualified service shop only.

On placement

. Place the player in a location with adequate

ventilation to prevent heat build-up in the player.

. Do not place the player on a soft surface such as

a rug that might block the ventilation holes on the bottom.

l Do not place the player in a location near heat

sources, or in a place subject to direct sunlight,

excessive dust, or mechanical shock.

On operation

l If the player is brought directly from a cold to a

warm location, or is placed in a very damp room, moisture may condense on the lenses inside the player. Should this occur, the player may not operate properly. In this case, remove the disc and leave the player turned on for about half an hour until the moisture evaporates.

l When you move the player, take out any discs. If

you don’t, the disc may be damaged.

On adjusting volume

Do not turn up the volume while listening to a section with very low level inputs or no audio signals. If you do, the speakers may be damaged when a peak level section is played.

On cleaning

Clean the cabinet, panel, and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine. If you have any questions or problems concerning your player, please consult your nearest Sony dealer.

On cleaning discs

Do not use a commercially available cleaning disc. It may cause a malfunction.

IMPORTANT NOTICE

Caution: This player is capable of holding a still video image or on-screen display image on your television screen indefinitely. If you leave the still video image or on-screen display image displayed on your TV for an extended period of time you risk permanent damage to your television screen. Projection televisions are especially susceptible to this.

Table of Contents

WARNING

.........................

Welcome! ..........................

Precautions ........................

About this Manual ...................

This Player Can Play the Following Discs

Notes about the Discs ................

index to Parts and Controls ............

Guide to the Control Menu Display ......

. . . . .

. .

. . . .

. .

. . .

. .

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Quick Overview

..................................

. .

.15

Stepl:Unpacking

................................

. .

.15

Step 2: Inserting Batteries into the Remote

.............

.I5

Step3:TVHookups..

.............................

.16

Step 4: Playing a Disc

.............................

.17

Hookups

.......................................

..I 8

2 . . 2 . . 3 . . 6

8 :;2

Hooking Up the Player

............................

. .I8

Step 1: Connecting the Video Cords

.................

. .I8

Step 2: Connecting the Audio Cords

.................

.20

Step 3: Connecting the Power Cord

..................

. .27

Step 4: Quick Setup

..............................

. .27

Playing Discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Playing Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Resuming Playback from the Point Where You Stopped the Disc

(Resume Play) . . . . . . . . . . . . . . . . . . . .

Using the DVD’s Menu . . . . . . . . . . . . . . . . . . . .

Selecting “ORIGINAL” or “PLAY LIST” on a DVD-RW Disc

. . . .

Selecting a Playback Area for an SACD Disc . . . . . . . . . . . .

Playing VIDEO CDs with PBC Functions (PBC Playback)

. .

Various Play Mode Functions (Program Play, Shuffle Play,

Repeat Play, A-B Repeat Play) . . . . . . . . . . . . . . . . . . . . .

.32 .33

.34 .35 .36 .37

.38

Searching for a Scene

...............................

.44

Searching for a Particular Point on a Disc

(Search, Scan, Slow-motion Play, Freeze Frame)

..................

.44

Searching for a Title/Chapter/Track/Index/Scene

.....................

.46

Searching by Scene (VIEWER)

...................................

.47

Viewing Information About the Disc

......................

Viewing the Playing Time and Remaining Time on the

Front Panel Display

..........................................

Checking the Playing Time and Remaining Time

......................

Checking the Play Information (ADVANCED)

........................

.................................

ChangingtheSound

............................................

SURROUND Mode Settings

......................................

.................

ChangingtheAngles

...........................................

Displaying the Subtitles

.........................................

Adjusting the Picture Quality (BNR)

................................

Adjusting the Playback Picture (VIDEO EQUALIZER)

..................

Enhancing the Playback Picture (DIGITAL VIDEO ENHANCER)

......... 63

Using Various Additional Functions

......................

Locking Discs (CUSTOM PARENTAL CONTROL,

PARENTAL CONTROL)

...................................... 64

Operation Sound Effects (Sound Feedback)

.........................

Controlling Your TV or AV Amplifier (Receiver) with the

Supplied Remote

...........................................

...............

. .

............

Using the Setup Display

.........................................

Setting the Display or Sound Track Language (LANGUAGE SETUP)

...... 73

Settings for the Display (SCREEN SETUP)

..........................

Custom Settings (CUSTOM SETUP)

............................... 75

Settings for the Sound (AUDIO SETUP)

............................

Settings for the Speakers (SPEAKER SETUP)

.......................

“b-----

..........................

..8 3

Troubleshooting ...............................................

Self-diagnosis Function (When letters/numbers appear in the display)

..... 86

Glossary .....................................................

Specifications .................................................

LanguageCodeList

............................................

List of Setup Display Items

.......................................

Index.. ......................................................

/ Format of discs

About this Manual

Instructions in this manual describe the controls on the remote. You can also use the controls on the player if they have the same or similar names as those on the remote.

The meaning of the icons used in this manual is described below:

Icon

Meaning

Functions available for DVD

lm!lm

VIDEOS or DVD-RslDVD-RWs in Video mode

Functions available for DVD-

m RWs in VR (Video Recording)

mode

Functions available for VIDEO CDs or CD-RsKD-RWs

Functions available for Super Audio CDs

Functions available for music CDs or CD-R&D-RWs

.‘I’.

More convenient features

“DVD” may be used as a general ierm for DVD VIDEOS, DVD-Rs, and DVD-RWs.

This Player Can Play the

Following Discs

Format of discs

DVD VIDEO

DVD-RW ZE

VIDEO CD

Music CD

DIGITAL AUDIO

“DVD VIDEO”

and “DVD-RW” are trademarks

Your player has a region code printed on the back of the unit and only will play DVD VIDEO discs (playback only) labeled with identical region codes.

DVDs labeled ALL will also play on this

player.

If you try to play any other DVD, the

message “Playback prohibited by area limitations.” will appear on the TV screen. Depending on the DVD, no region code indication may be labeled even though playing the DVD is prohibited by area restrictions.

The player cannot play the following discs:

CD-ROMs (PHOTO CDs included)

All CD-Rs/CD-RWs other than music and VCD format CD-Rs/CD-RWs

Data part of CD-Extras

DVD-ROMs

DVD Audio discs

Also, the player cannot play the following

A disc recorded in a color system other than NTSC, such as PAL or SECAM (This player conforms to the NTSC color system).

A DVD with a different region code (page

86).

A disc that has a non-standard shape (e.g.,

card, heart).

A disc with paper or stickers on it.

A disc that has the adhesive of cellophane tape or a sticker still left on it.

Some DVD-Rs, DVD-RWs, CD-Rs, or CD-RWs cannot be played on this player due to the recording quality or physical condition of the disc, or the characteristics of the recording device. DVD-RWs in VR mode may also take time to playback due to the recording condition. Furthermore. the disc will not play if it has not been correctly finalized. For more information, see the operating instructions for the recording device.

Some playback operations of DVDs and VIDEO CDs may be intentionally set by software producers. Since this player plays DVDs and VIDEO CDs according to the disc contents the software producers designed, some playback features may not be available. Also, refer to the instructions supplied with the DVDs or VIDEO CDs.

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents, other intellectual property rights owned by Macrovision Corporation, and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or

disassembly is prohibited.

Notes about the Discs

On handling discs

To keep the disc clean, handle the disc by its edge. Do not touch the surface.

Do not expose the disc to direct sunlight or heat sources such as hot air ducts, or leave it in a car parked in direct sunlight as the temperature may rise considerably inside the car.

After playing, store the disc in its case.

On cleaning

Before playing, clean the disc with a cleaning cloth. Wipe the disc from the center out.

Do not use solvents such as benzine, thinner, commercially available cleaners, or anti-static spray intended for vinyl LPs.

Index to Parts and Controls

For more information, refer to the pages indicated in parentheses.

POWER switch/indicator (32)

DVD indicator Lights up when the disc is a DVD

SACD indicator Lights up when the disc is an SACD

MULTI CHANNEL indicator Lights up when:

- playing a disc that contains more than 3 audio signal channels

- the disc is not inserted

Disc tray (32)

0 (open/close) button (32)

w/H (previous/next) buttons (33)

t/q/+/+/ ENTER buttons (27)

JOG button/indicator (45)

TOP MENU button (34)

MENU button (34)

o? RETURN button (37)

DISPLAY button (12)

Click shuttle (45)

H (stop) button (32)

II (pause) button (33) (68)

D (play) button (32)

Front panel display (9)

SURROUND button/indicator (55)

BNR (Block Noise Reduction) button/ indicator (61)

(remote sensor) (15)

When playing back a DVD VIDEO/DVD-RW

Lights up when you can change the angle (59)

Disc type

Playing status

TITLE

: ! .

#ANGLE HOUR MIN SEC;

:---

. . . . . . .

: 1.

““-: “““‘:

f....,; i

:- . . . . ..j

:...w ;.....C

i i

. . . . . . . :+..A

. ..-L!.

--it....

I.....! i

” . . . . . . . -..

Currentaudio Current play Current title (49) Current chapter (49)

Playing time (49)

signal (54)

mode (38)

When playing back a VIDEO CD (PBC)

Disc type Playing status

m:+ii

MiN

. . . . . . . . . . . . . . .

: : :

; . . . . ..~

““?

SEC;

:-“”

. . . . . . . . f . . . . . . I

. . . . ..r . . . . . . . i i.....

A-B’

: :

: .:

L.... : ,..... 1 :.:,.r...r L,.; .~ . . . . ;:. :

Current play mode (38)

Playing time (49)

Current scene (49)

When playing back an SACD, CD, or VIDEO CD (without PBC)

Playing

Lights up when playing the multi-

Disc type:: status

channel playback area on SACDs (36)

TRACK, INDEX‘

MIN

---- sic:

;

Current play mode (38)

Current track and index (49)

Playing time (49)

::: When playing the SACD layer of SACD discs, the disc type is not displayed

continued -

DIGITAL OUT (COAXIAL) jack (22) (24) (25)

DIGITAL OUT (OPTICAL) jack (22)

(24) (25)

LINE OUT (VIDEO) l/2 jacks (18)

S VIDEO OUT l/2 jacks (18)

COMPONENT VIDEO OUT jacks (18)

5.1CH OUTPUT jacks (22)

LINE OUT L/R (AUDIO) l/2 jacks (21) (24) (25)

TV/DVD switch (69)

k OPEN/CLOSE button (33)

Number buttons (34)

The number 5 button has a tactile dot.

CLEAR button (38) (69)

SACD MULTI12CH button (36)

SACD/CD button (36)

AUDIO button (53)

ANGLE button (59)

SHUFFLE button (40)

PROGRAM button (38)

w/w PREV/NEXT (previous/next)

buttons (33)

411@/811) SEARCH/STEP buttons

(44)

D PLAY button (32) The D PLAY button has a tactile dot.

TOP MENU button (34)

DISPLAY button (38)

I/& (on/standby) button (32) (69)

VOL (volume) +/-buttons (69) The + button has a tactile dot.

TV/VIDEO button (69)

WIDE MODE/DVE (Digital Video

Enhancer) (63) (69)

ENTER button

BNR (Block Noise Reduction) button

(61)

SEARCH MODE button (46)

TIME/TEXT button (49)

SUBTITLE button (60)

A-B button (42)

REPEAT bu’tton (4 1)

REPLAY button (33)

SURROUND button (55)

-rl@/@b

SCAN/SLOW buttons (44)

STOP button (32)

II PAUSE button (33)

MENU button (34)

tl*l+l+ buttons (27)

q O?

RETURN button (37)

ENTER button (27)

Guide to the Control Menu Display

Use the Control Menu to select a function that you would like to

use.

The Control Menu display

appears when the DISPLAY button is pressed. For details, please refer to the page in parentheses.

Total number of titles or tracks recorded

Currently playing title number (VIDEO CD/SACD/CD: track number)

Currently playing chapter number (VIDEO CD/SAC CD: index number)

Total number of chapters or indexes recorded

Icon of selected --

Control Menu item

Control Menu items

Function name of selected Control Menu item

Operation message -.--

List of Control Menu Items

46)BCENE (page Selects the title, scene, or track to be played.

CHAPTER (page 46)ANDEX

ORIGINAL/PLAY LIST (page

Selects the chapter or index to be played.

Selects the track to be played. Selects the index to be played. Checks the elapsed time and the remaining

playback time. Input the time code for picture and music searching.

Displays the DVD or SACDKD text.

Selects the type of titles (DVD-RW) to be played, the ORIGINAL one, or an edited PLAY LIST.

Changes the audio setting. Selects the playback area on 2 channel+Multi-

channel SACDs.

SUBTITLE (page 60)

Displays the subtitles. Changes the subtitle language.

ANGLE (page 59)

Changes the angle.

SURROUND (page 55)

Selects the surround functions.

ADVANCED (page 52)

Checks the information (bit rate or layer) on the disc while playing a DVD.

PARENTAL CONTROL (page

Sets the disc to prohibit playing.

SETUP (page 72)

QUICK Setup (page 27) Use Quick Setup to choose the desired language of the on-screen display, the aspect ratio of the TV, the audio output, and the appropriate speaker settings. CUSTOM Setup In addition to the Quick Setup setting, you can adjust the image and sound quality, and other various settings. RESET Returns the settings in “SETUP” to the default setting.

PROGRAM (page 38)

Selects the title, chapter, or track to play a disc in the order you want.

SHUFFLE (page 40)

Plays the title, chapter, or track in random order.

_..

REPEAT (page 41)

Plays the entire disc (all titles/all tracks) repeatedly or one title/chapter/track

repeatedly. A-B REPEAT (page 42) Specifies the parts you want to play repeatedly. BNR (page 61)

Adjusts the picture quality by reducing the

“block noise” or mosaic like patterns that

appear on your TV screen. VIDEO EQUALIZER (page 62) Adjusts the video signal from the player. You

can select the picture quality that best suits the

program you are watching. DIGITAL VIDEO ENHANCER Exaggerates the outline of the image to

)

produce a sharper picture. VIEWER (page 47)

Divides the screen into 9 subscreens to help

you find the scene you want quickly.

.“‘.

$’ Each time you press DISPLAY, the Control Menu display changes as follows:

Control Menu display I

Control Menu display 2

ADVANCED display (Appears if you select any setting other than “OFF.” See page 52.)

Control Menu display off

When playing an SACDKD disc, only the Control Menu display 1 will appear. The Control Menu items are different depending on the disc.

.*‘a.

c The Control Menu icon indicator lights up in green

when you select any item except “OFF.” (“SURROUND,” “PROGRAM,” “SHUFFLE,” “REPEAT,” “A-B REPEAT,” “BNR,” “DIGITAL VIDEO ENHANCER” only). The “ANGLE” indicator lights up in green only when the angles can be changed. The “VIDEO EQUALIZER” indicator lights up in green when any setting other than “STANDARD” is selected.

Quick Overview

A quick overview presented in this chapter will give you enough information to start using the player for your enjoyment. To use the surround sound features of this player, refer to “Hookups” on page 18.

You cannot connect this player to a TV that

does not have a video input jack.

sure to turn off the power of each component before connecting.

Step 1: Unpacking

Check that you have the following items:

Audio/video cord (pinplug x 3 ++ pinplug x 3) (1)

Remote commander (remote) RMT-D 13 1 A (1)

Size AA (R6) batteries (2)

Step 2: Inserting Batteries into the Remote

You can control the player using the supplied remote. Insert two size AA (R6) batteries by matching the @ and 0 ends on the batteries to the markings inside the compartment. When using the remote, point it at the remote sensor q on the player.

Do not leave the remote in an extremely hot or humid place.

Do not

drop any foreign object into the remote casing, particularly when replacing the batteries.

Do not expose the remote sensor to direct light from the sun or a lighting apparatus. Doing so may cause a malfunction.

If you do not use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion.

Step 3: TV Hookups

Connect the supplied audio/video cord and the power cord in the order (m-m) shown below. Be sure to connect the power code last.

, _, , . l”./_ ‘, i

to LINE OUT L/R LINE ( (AUDIO) 1

IDEO)

,I ,,,, A,, j

3JT

SACD!DVD Player

u Power source

Power source

When connecting to a wide screen TV Depending on the disc, the image may not fit your TV screen.

If you want to change the aspect ratio, please refer to page 74.

? Step 4: Playing a Disc

Turn on the TV.

Switch the input selector on the TV to the player.

With the playback side facing down

Press POWER on the player.

Press 62 on the player to open the disc tray.

Place the disc on the tray with the playback side facing down.

Press D.

The disc tray closes and the player begins playing the disc.

After Step 6

Depending on the disc, a menu may be displayed on the TV screen. If so, select the item you want from the menu and play the DVD VIDEO (page 34) or VIDEO CD disc (page 37).

To stop playing

Press H.

To take out the disc Press 6.

To turn off the player Press

l/O

on the remote. The player is set to standby mode and the power indicator lights up in

red. Press POWER on the player to turn off completely.

Hooking Up the Player

Follow Steps 1 to 4 to hook up and adjust the settings of the player. Before you start, turn off the power, check that you have all of the supplied accessories, and insert the batteries into the remote (page 15).

Plug cords securely to prevent unwanted noise.

Refer to the instructions supplied with the components to be connected.

Step 1: Connecting the Video Cords

Connect this player to your TV monitor, projector, or AV amplifier (receiver) using a video cord. Select one of the patterns @ through 0, according to the input jack on your TV monitor, projector, or AV amplifier (receiver).

S VIDEO cord (not supplied)

d : Signal flow

tf ~~~

Connect the yellow plug of the audio/video cord (supplied) to the yellow (video) jacks. You will enjoy standard quality images.

Yellow (Video) Yellow (Video) White (L)

White (L)

Red (R)

Use the red and white plugs to connect to the audio input jacks (page 21).

Connect the S VIDEO cord (not supplied). You will enjoy high quality images.

Connect the component via the COMPONENT VIDEO OUT jacks using the component video cord (not supplied) or three video cords (not supplied) of the same kind and length. You will enjoy accurate color reproduction and high quality images.

Green

Blue Red

Green Blue Red

Do not connect the player to a VCR. If you pass the player signals via the VCR, you may not receive a clear image on the TV screen.

Step 2: Connecting the Audio Cords

Refer to the chart below to select the connection that best suits your system. The surround effects you will enjoy depend on the connections and components you use.

Select one of the following connections, m through a.

Connection

(page 2 1)

a (page

22)

Components to be connected TV (stereo) AV amplifier (receiver) having 5. Ich input jacks

l 4 speakers

(front L and R, rear L and R)

l 6 speakers

a (page

22)

(front L and R, center, rear L and R, subwoofer)

AV amplifier (receiver) having a Dolby* Digital or DTS** decoder and a digital input jack

l 6 speakers

(front L and R, center, rear L and R, subwoofer)

m (page 24)

Stereo amplifier (receiver) (having L and R audio input jacks only, or having a digital input jack)

l 2 speakers

(front L and R)

m (page 24) m (page 25)

MD deck/DAT deck AV amplifier (receiver) with a Dolby Surround (Pro Logic) decoder

(having L and R audio input jacks only, or having a digital input jack)

l 3 speakers

(front L and R, and rear (monaural))

l 6 speakers

(front L and R, center, rear L and R, subwoofer)

‘c To enjoy SACD Multi or 96kHz/24bit sound, use the connection e.

* Manufactured under license from Dolby Laboratories. “Dolby,” “ Pro Logic,” and the double-r) symbol are

** Manufactured under license from Digital Theater Systems, Inc. US Pat. No. 5,451,942 and other world-wide

This connection will use your TV speakers for sound.

Recommended surround sound effects for this connection

TVS DYNAMIC (page 55)

*TVS WIDE (page 55)

Audio/video cord

d : Signal flow

The yellow plug is used for video signals (page 18).

continued -

If your AV amplifier (receiver) has 5.1 channel inputs, use m. If you want to use the Dolby Digital or DTS decoder function on your AV amplifier (receiver), connect to its digital jack using m. With the following connections, you can enjoy a more realistic audio presence in the comfort of your own home.

a: Connecting to the 5.lch input jacks

You can enjoy 5.lch surround sound using the internal Dolby Digital, DTS, or SACD Multi decoder of this player. You can also enjoy Dolby Surround (Pro Logic) sounds, or surround sounds using various “SURROUND’ modes (page 55).

n Recommended surround sound effects for this connection

When 6 speakers are connected. (Set “SURROUND’ to “OFF.“)

*Dolby Digital (5.lch) (page 86)

l DTS (5.lch) (page 86)

SACD Multi channel (page 86)

@: Connecting to a digital jack

This connection will allow you to use the Dolby Digital or DTS decoder function of your AV amplifier (receiver). You are not able to enjoy the surround sound effects of the player.

HRecommended surround sound effects using this connection with your

amplifier (receiver)

*Dolby Digital (5. lch) (page 86) l DTS (Klch) (page 86)

96kHz/24bit PCM

l After you have completed the connection, be sure to set “DOLBY DIGITAL” to “DOLBY DIGITAL” (page 27)

and “DTS” to “DTS” (page 27). Otherwise, no sound or a loud noise will come from the speakers.

l When you connect an amplifier (receiver) that conforms to the 96kHz sampling frequency, set “48kHz/96kHz

PCM” to “96kHz/24bit” (page 78).

l SACD audio signals are not output from the digital jack.

SACDIDVD player

: Optical digital cord

j ri (not supplied)

Remove jack cap before connecting

Stereo audio cord (not supplied)

Coaxial digital cord

to coaxial or optical digital input

Monaural audio cord (not supplied)

to audio input

[Speakers] 1 1 [Speakers]

d: Signal flow

.“‘.

$’ To enhance the surround sound effects:

l Use high-performance speakers. l Use front, rear, and center speakers having the same size and performance. l Place a subwoofer between the right and left front speakers. l When using connection e, refer to the operating instructions of the receiver (amplifier) for correct speaker

setting location.

continued -

This connection will use your 2 front speakers connected to your stereo amplifier (receiver) for sound. If the stereo amplifier (receiver) has audio input jacks L and R only, use m. If the amplifier (receiver) has a digital input jack, use e. When connecting to an MD deck or a DAT deck, use m. In this case, you can also connect the player directly to the MD deck or DAT deck without using your stereo amplifier (receiver).

n Recommended surround sound effects for the m connection only

*TVS STANDARD (page 55)

‘;cs’ In connection e, you can use the supplied audio/video cord instead of using a separate audio cord L’..

9 To realize better surround sound effects, make sure that your listening position is in between your speakers

SACD audio signals are not output from the digital jack

SACD/DVD playar

Coaxial

digital cord

(not supplied)

Stereoaudiocord (not supplied)

Optical digital cord(not supplied) Remove jack cap before connecting

to coaxial or optical digital

inpa

(white)

or R-AUDIO?-I VIDEO*

(red)

to audio input

[Speakers]

Stereo amplifier (receiver)

A: Signal flow

This connection will allow you to enjoy the surround effects of the Dolby Surround (Pro Logic) decoder on your amplifier (receiver). If you have an AV amplifier (receiver) equipped with a Dolby Digital or DTS decoder, refer to page 22. You can enjoy the Dolby Surround effects only when playing Dolby Surround audio or multichannel audio (Dolby Digital) discs.

This connection needs a minimum of 3 speakers (front L and R, and rear (monaural)). The

surround effects are enhanced if 6 speakers (front L and R, center, rear L and R, and subwoofer)

are used. If your amplifier (receiver) has L and R audio input jacks only, use m. If your amplifier (receiver) has a digital input jack, use a.

WRecommended surround sound effects using this connection with your amplifier (receiver)

Dolby Surround (Pro Logic) (page 86)

.S”.

c For correct speaker setting location, please refer to the operating instructions of the amplifier (receiver)

SACD audio signals are not output from the digital jack

continued -

(whit

(red)

to audio input

Optical digital cord (not supplied) Remove jack cap before connecting

to coaxial or optical digital inpu

6: Signal flow

*When connecting 6 speakers, replace the monaural rear speaker with a center speaker, 2 rear speakers and a

subwoofer.

Step 3: Connecting the Power Cord

Plug the player and TV power cords into an AC outlet. Do not connect the power cord of your player to the “switched” power socket of an amplifier

(receiver). When you turn off the power of your amplifier (receiver), the menu setting for the player such as Playback Memory may be lost.

5 g

Step 4: Quick Setup

Follow the steps below to make the minimum number of basic adjustments for using the player. To skip an adjustment, press w. To return to the previous adjustment, press H.

ENTER

I I

- +I*

- ENTER

Turn on the TV.

Switch the input selector on the TV to the player.

Press POWER on the player and press I/& on the remote.

“Press [ENTER] to run QUICK SETUP” appears at the bottom of the screen. If this message

does not appear, select “QUICK” under “SETUP” in the Control Menu to run Quick Setup

(page 72).

con timed -

Press ENTER without inserting a disc.

The Setup Display for selecting the language used in the on-screen display appears.

FJ Press W to select a language.

The player uses the language selected here to display the menu and subtitles as well.

Press ENTER.

The Setup Display for selecting the aspect ratio of the TV to be connected appears.

Press +/4+ to select the item.

TV Twe

You select Paae

4:3 standard TV

4:3 LETTER BOX or 4:3 PAN SCAN

A wide-screen TV or a 4:3 standard TV with a wide-screen mode

16:9 74

Press ENTER.

The Setup Display for selecting the type of jack used to connect your amplifier (receiver) appears.

Press W to select the item, then press ENTER.

Audio Cord Connecting Type You select

aDaD

LINE OUTPUT L/R (AUDIO)

aae

DIGITAL OUTPUT

m or both 0) and m

DIGITAL & 5. I CH OUTPUT

When “NO” or “LINE OUTPUT L/R (AUDIO)” is selected, Quick Setup is finished and connections are complete.

When “DIGITAL OUTPUT” or “DIGITAL & 5. ICH OUTPUT” is selected, the

Setup

Display for “DOLBY DIGITAL” appears.

Press +/+ to select the item.

Choose the item that matches the audio connection you selected in page 22 to 25 (e through m).

Audio Cord Connection Type

You select

Page

D-PCM 78 DOLBY DIGITAL (only if the

amplifier (receiver) has a Dolby

Digital decoder)

Press ENTER.

“DTS” is selected.

Press +/+ to select the item.

Choose the item that matches the audio connection you selected in page 22 to 25 (e through e).

Audio Cord Connection Type

You select

Page

D-PCM 78

DTS (only if the amplifier 78 (receiver) has a DTS decoder)

Press ENTER.

When “DIGITAL OUTPUT” is selected in Step q , Quick Setup is finished. All connections and setup operations are complete.

When “DIGITAL & 5.lCH OUTPUT” is selected in Step q , the Setup Display for

“SPEAKER SETUP” appears.

con timed -

H Press W to select the size of the center speaker.

If no center speaker is connected, select “NONE.” Refer to page 80 for each selection item.

Press ENTER.

The Setup Display for selecting the size of the rear speaker appears.

Press +/JI to select the size.

If no rear speaker is connected, select “NONE.” “SIDE” and “REAR’ refer to the speakers’ position relative to your listening position. Refer to page 80 for each selection item.

Press ENTER.

The Setup Display for selecting whether or not you have connected a subwoofer appears.

Press W to select the item.

Press ENTER.

Quick Setup is finished. All connections and setup operations are complete.

You can directly start Quick Setup only when you run it for the first time. To run Quick Setup a second time, select “QUiCr under “SETUP” in the Control Menu (page 72)

+ 77 hidden pages

Sony DVP-NSSOOV Operating Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual