Sony DVP-NS975V User Manual

2-059-565-11(4)

CD/DVD Player

Operating Instructions

For customers in the U.S.A Owner’s Record

The model and serial numbers are located at the rear of the unit. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product.

Model No. DVP-NS975V Serial No.______________

For Customers in Canada

If this product is not working properly, please call 1-877-602-2008 for

Peace of Mind Warranty Replacement service. For other product related questions please contact our Customer Information Service Centre at 1-877-899-7669 or write to us at:

Customer Information Service 115 Gordon Baker Road, Toronto, Ontario, M2H 3R6

DVP-NS975V

WARNING

To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

The AC power cord must be changed only at a qualified service shop.

CAUTION

The use of optical instruments with this product will increase eye hazard. As the laser beam used in this CD/DVD player is harmful to eyes, do not attempt to disassemble the cabinet. Refer servicing to qualified personnel only.

This symbol is intended to alert the user to the presence of uninsulated

within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION

You are cautioned that any change or modifications not expressly approved in this manual could void your authority to operate this equipment.

“dangerous voltage”

This symbol is intended to alert the user to the presence of important operating and

Note

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the

receiving antenna.

– Increase the separation between

the equipment and receiver.

– Connect the equipment into an

outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an

experienced radio/TV technician for help.

Welcome!

Thank you for purchasing this Sony CD/DVD Player. Before operating this player, please read this manual thoroughly and retain it for future reference.

Important Safeguards

For your protection, please read these safety instructions completely before operating the appliance, and keep this manual for future reference. Carefully observe all warnings, precautions and instructions on the appliance, or the one described in the operating instructions and adhere to them.

Use

Power sources

This set should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of electrical power supplied to your home, consult your dealer or local power company. For those sets designed to operate from battery power, or other sources, refer to the operating instructions.

Grounding or Polarization

This set is equipped with a polarized ac power cord plug (a plug having one blade wider than the other), or with a three-wire grounding type plug (a plug having a third pin for grounding). Follow the instructions below:

For the set with a polarized AC power cord plug:

This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to have a suitable outlet installed. Do not defeat the safety purpose of the polarized plug by forcing it in.

For the set with a three-wire grounding type AC plug:

This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to have a suitable outlet installed. Do not defeat the safety purpose of the grounding plug.

Overloading

Do not overload wall outlets, extension cords or convenience receptacles beyond their capacity, since this can result in fire or electric shock.

Object and Liquid Entry

Never push objects of any kind into the set through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the set.

Attachments

Do not use attachments not recommended by the manufacturer, as they may cause hazards.

Cleaning

Unplug the set from the wall outlet before cleaning or polishing it. Do not use liquid cleaners or aerosol cleaners. Use a cloth lightly dampened with water for cleaning the exterior of the set.

Installation

Water and Moisture

Do not use power-line operated sets near water - for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc.

Power-Cord Protection

Route the power cord so that it is not likely to be walked on or pinched by items placed upon or against them, paying particular attention to the plugs, receptacles, and the point where the cord exits from the appliance.

Accessories

Do not place the set on an unstable cart, stand, tripod, bracket, or table. The set may fall, causing serious injury to a child or an adult, and serious damage to the set. Use only a cart stand tripod, bracket, or table recommended by the manufacturer.

An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

S3125A

Ventilation

The slots and openings in the cabinet are provided for necessary ven tila tion. To ensure reliable operation of the set, and to protec t it from overheating, these slots and openings must never be blocked or covered.

• Never cover the slots and openings with a cloth or other materials.

• Never block the slots and openings by placing the set on a bed, sofa, rug or other similar surface.

,continued

• Never place the set in a confined space, such as a bookcase, or built-in cabinet, unless proper ventilation is provided.

• Do not place the set near or over a radiator or heat register, or where it is exposed to direct sunlight.

Antennas Outdoor antenna grounding

If an outdoor antenna or cable system is installed, follow the precautions below.

An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits. WHEN INSTALLING AN OUTDOOR ANTENNA SYSTEM, EXTREME CARE SHOULD BE TAKEN TO KEEP FROM CONTACTING SUCH POWER LINES OR CIRCUITS AS CONTACT WITH THEM IS ALMOST INVARIABLY FATAL. Be sure the antenna system is grounded so as to provide some protection aga inst voltage surges and built-up static charges. Section 810 of the National E lectrical Code provides information with respect to proper groun ding of the mast and supporting structure, grounding o f the lead-in wire to an antenn a disc ha rge unit, size of grounding conductors, location of antenn a-discharge unit, connection to grounding electrodes, a nd requirements for the grounding electrode.

Antenna Grounding According to the National Electrical Code

Antenna Lead in Wire

Ground Clamp

Electric Service Equipment

NEC-NATIONAL ELECTRICAL CODE

Lightning

For added protection for this set during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the set due to lightning and powerline surges.

Antenna Discharge unit (NEC Section 810-20)

Grounding Conductors (NEC Section 810-21)

Ground Clamps

Power Service Grounding Electrode System (NEC Art 250 Part H)

Service

Damage Requiring Service

Unplug the set from the wall outlet and refer servicing to qualified service personnel under the following conditions:

• When the power cord or plug is damaged or fraye d.

• If liquid has been spilled or objects have fallen into the set.

• If the set has been exposed to rain or water.

• If the set has been subject to excessive shock by being dropped, or the cabinet has been damage d.

• If the set does not operate normally when following the operating instructions. Adjust only those controls that are specified in the operating in structions. Improper ad justment of other contro ls may result in damage and will often require extensive work by a qualified technician to restore the set to normal operation.

• When the set exhibits a distinct change in performance - this indicates a need for service.

Servicing

Do not attempt to service the set yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

Replacement parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock, or other hazards.

Safety Che ck

Upon completion of any service or repairs to the set, ask the service technician to perform routine safety checks (as specified by the manufacturer) to determine that the set is in safe operating condition.

Precautions

• The power requirement s and power consumption of this player are indicated on the back of the play er . Check that the player’s operating voltage is identical with your local power supply.

Power requirements and power consumption t

00W

On safety

• To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the app aratus.

• Should any solid object or liquid fall into the cabinet, unplu g the player and have it checked by quali f ie d personnel before operating it any further.

On power sources

• The player is not disc onnect ed from the A C power source as long as it is connected to the wall outlet, even if the player itself has been turned off.

• If you are not going to use the player for a long time, be sure to disconnect the player from the wall outlet. To disconnect the AC power cord, grasp the plug itself; never pull the cord.

On placement

• Place the player i n a l ocat io n with a dequ at e ventilation to prevent heat build-up in the player.

• Do not place the player on a sof t sur fa ce such as a rug.

• Do not p l ace the player in a locati on near heat sources, or in a place subject to di rect sunlight, excessive dust, or mechanical shock.

• Do not install the player in an inclined position. It is des i gned to be operated in a horizontal position only.

• Keep the player and the discs away from equipment with st rong magnets, such as microwave ovens, or large loudspeakers.

• Do not place heavy objects on the player.

00V 00Hz

NO.

DVP–XXXX

0-000-000-00

On operation

• If the player is brought di re ctl y from a cold to a warm location, or is placed in a very damp room, moisture may condense on th e lenses inside the player. Should this occur, the player may not operate properly. In this case, remove the disc and leave the player turned on for about half an hour until the moisture evaporates.

• When you move the player, take out any discs. If you do n’t, the disc may be damaged.

On adjusting volume

Do not turn up the volume while listening to a section with very low level inputs or no audio signals. If you do, the speakers may be damaged when a pe ak l eve l se cti on is pl ay ed.

On cleaning

Clean the cabinet, panel, and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine.

On cleaning discs

Do not use a commercially available cleaning disc. It may cause a malfunction.

IMPORTANT NOTICE

Caution: This player is capable of holding a still video image or on-screen display image on your television screen indefinite ly . I f you leave the still video image or on-screen display ima ge displayed on your TV for an extended period of time you risk permanent damage to your te levision screen . Plasma display panel televisions and projection televisions are susceptible to this.

If you have any questi ons or problems concerning your player, please consult your nearest Sony dealer.

Table of Contents

WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Welcome!. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

About This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

This Player Can Play the Following Discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Notes About the Discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Index to Parts and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Guide to the Control Menu Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Hookups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Hooking Up the Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Step 1: Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Step 2: Inserting Batteries Into the Remote. . . . . . . . . . . . . . . . . . . . . . . . . . 18

Step 3: Connecting the Video/HDMI Cords . . . . . . . . . . . . . . . . . . . . . . . . . 19

Step 4: Connecting the Audio Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Step 5: Connecting the Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Step 6: Quick Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Playing Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Playing Discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Resuming Playback Fro m the Poi nt Where You Stopped the Disc

(Multi-disc Resume) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Using the DVD’s Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Selecting “ORIGINAL” or “PLAY LIST” on a DVD-RW . . . . . . . . . . . . . . . . . 38

Selecting a Playback Area for a Super Audio CD . . . . . . . . . . . . . . . . . . . . . 39

Playing VIDEO CDs With PBC Functions (PBC Playback) . . . . . . . . . . . . . 40

Various Play Mode Functions

(Program Play, Shuffle Play, R epeat Play, A-B Repeat Play) . . . . . . . . . 41

Searching for a Scene . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Searching for a Particular Poin t on a Disc

(Search, Scan, Slow-motion Play, Freeze Frame). . . . . . . . . . . . . . . . . . 46

Searching for a Title/Chap t er/Tr ac k/ Scene, etc. (Search mode) . . . . . . . . . 47

Searching by Scene (PICTURE NAVIGATION) . . . . . . . . . . . . . . . . . . . . . . 49

Viewing Information About the Disc . . . . . . . . . . . . . . . . . . . . . . . 50

Checking the Playing Time and Remaining Time . . . . . . . . . . . . . . . . . . . . . 50

Sound Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Changing the Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Surround Mode Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Enjoying Mo vies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 8

Changing the Angles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Displaying the Subtitles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Adjusting the Playback Picture (CUSTOM PICTURE MODE). . . . . . . . . . . . 59

Sharpening the Pictures (SHARPNESS). . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Adjusting the Delay Betwe en the Picture and Sound (AV ALIGNM E NT) . . . 61

Enjoying MP3 Audio and JPEG Images . . . . . . . . . . . . . . . . . . . . . 62

About MP3 Audio Tracks and JPEG Image Files . . . . . . . . . . . . . . . . . . . . . 62

Playing MP3 Audio Tracks or JPEG Image Files . . . . . . . . . . . . . . . . . . . . . 63

Enjoying JPEG Images as a Slide Show . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Using Various Additional Functions . . . . . . . . . . . . . . . . . . . . . . . 70

Locking Discs

(CUSTOM PARENTAL CONTROL, PARENTAL CONTROL). . . . . . . . . 70

Controlling Your TV or AV Amplifier

(Receiver) With the Supplied Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Settings and Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Using the Setup Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Setting the Display or Sound Tra ck Language (LANGUAGE SETUP) . . . . . 78

Settings for the Display (SCREEN SETUP). . . . . . . . . . . . . . . . . . . . . . . . . . 79

Custom Settings (CUSTOM SETUP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Settings for the Sound (AUDIO SETUP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Settings for the Speakers (SPEAKER SETUP) . . . . . . . . . . . . . . . . . . . . . . . 85

Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Self-diagnosis Functio n (W hen letters/numbers appear in the display). . . . . 91

Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Language Code List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

About This Manual

This Player Can Play the

• Operations and displa ys d i ff er slightly, depending on wher e t he model is sold. U.S./Canadian models are used for illustration purposes unless otherwise specified. Any difference in operation is clearly indica te d in the text, for exam ple, “(U.S./Canadian models only).”

• Instructions in this manual describe the controls on the remote. You can also use the controls on the player if they hav e the same or similar names as those on the remote.

• “DVD” may be used as a general term for DVD VIDEOs, DVD+RWs/DVD+Rs and DVD-RWs/DVD-Rs.

• The meaning of the icons used in this manual is described below:

Icons Meanings

Functions available for DVD VIDEOs and DVD+RWs/ DVD+Rs or DVD-RWs/DVDRs in video mode

Functions available for DVDRWs in VR (Video Recording) mode

Functions available for VIDEO CDs (including Super VCDs or CD-Rs/CD-RWs in video CD format or Super VCD format)

Functions available for Super Audio CDs

Functions available for music CDs or CD-Rs/CD-RWs in music CD format

Functions available for DATA CDs (CD-ROMs/CD-Rs/CDRWs containing MP3* audio tracks and JPEG im ag e files)

* MP3 (MPEG1 Audio Layer 3) is a standard

format defined by ISO (International Organization for Standardization)/MPEG which compresses audio data.

Following Discs

Format of discs

DVD VIDEO (page 91)

DVD-RW (page 91)

Super Audio CD (page 91)

VIDEO CD

Music CD

“DVD VIDEO” and “DVD-RW” are trademarks.

Note about CDs

The player can pl ay CD-ROMs/CD-Rs/CDRWs recorded in the following formats: –music CD format –video CD form at –MP3 audio tracks and JPEG i m age files of

format conforming to ISO 9660* Level 1/ Level 2, or its extended format, Joliet

–KODAK Picture CD format

* A logical format of files and folders on CD-

ROMs, defined by ISO (International Organization for Standardization).

Example of discs that the player cannot play

The player cannot play the following dis cs:

• CD-ROMs/CD-Rs/CD-RWs other than those recorded in the formats listed on the previous page.

• CD-ROMs recorded in PHOTO CD format.

• Data part of CD-Extras.

• DVD-ROMs.

• DVD Audios.

Also, the player cannot play the following discs:

• A DVD VIDEO with a different region code.

• A disc recorded in a color system other than NTSC, such as PAL or SECAM (this player conforms to the NTSC color system).

• A disc that has a non-standard shape (e.g., card, heart).

• A disc with paper or stickers on it.

• A disc that has the adhesive of cellophane tape or a sticker still left on it.

Notes

• Notes about DVD+RWs/DVD+Rs, DVD-RWs/ DVD-Rs or CD-Rs/CD-RWs

Some DVD+RWs/DVD+Rs, DVD-RWs/DVDRs or CD-Rs/CD-RWs cannot be played on this player due to the recording quality or physical condition of the disc, or th e cha racteristics of the recording device and authoring softwa re . The disc will not play if it has not bee n corr e ct ly finalized. For more information, see the operating instructions for the recording device. Note that some playback functions may not work with some DVD+RWs/DVD+Rs, even if they have been correctly finalized. In this case, view the disc by normal playback. Also some DATA CDs created in Packet Write format cannot be played.

• Music discs encoded with co pyright protecti on

technologies

This product is designed to playback discs that conform to the Compact Disc (CD) standard. Recently, various music dis cs encode d wit h copyright protection technologies are marketed by some record companies. Please be aware that among those discs, there are some that do not conform to the CD standard and may not be playable by this product.

Region code

Your player has a region code printed on the back of the unit and onl y w ill play DVD VIDEOs (playback only) labeled with identical region codes. This sys tem is used to protect copyrig ht s.

ALL

Region code

DVD VIDEOs labelled will also play on this player.

If you try to play any other DVD VIDEO, the message “Pla yback prohibited by area limitations.” will appear on the TV screen. Depending on the DVD VIDEO, there may be no region code indi cation, even though playing the DVD VIDEO is prohibited by area restrictions.

00V 00Hz

NO.

DVP–XXXX

00W

0-000-000-00

Note on playback operations of DVDs and VIDEO CDs

Some playback operations of DVDs and VIDEO CDs may be intentionally set by software producers. Since this play er plays DVDs and VIDEO CDs according to the disc contents the software producers designed, some playback features may not be available. Also, refer to the instructions supplied with the DVDs or VIDEO CDs.

Copyrights

This product incorporates copyrigh t protection techn ol ogy that is protected by U.S. patents and oth er in te llectual property rights. Use of this copyright protection technology must be authorized by Macrovision, an d is in te nded for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineer i ng or disassembly is prohibited.

Notes About the Di sc s

• To keep the disc clean, h andle th e disc by its edge. Do not touch the surface.

• Do not expose the disc to direct sunlight or heat sources such as hot air ducts, or leave it in a car parked in dir ect sunlight as the temperature ma y rise considerably ins ide the car.

• After playing, store the disc in its case.

• Clea n t he disc with a cleaning cl ot h. Wipe the disc from the center out.

• Do no t use solvents such as benzine, thinner, commercially available cleaners, or anti-static spray intended for vinyl LPs.

• If you have printed the disc' s l abel, dry the label before pl aying.

Index to Parts an d Controls

For more information, see the pages indicated in parentheses.

Front panel

A [/1 (on/standby) button (34) B HDMI* (High-Definition Multimedia

Interface) indicator (20, 79, 84, 92) Lights up when the HDMI OUT jack is correctly connected to a HDCP (Highbandwidth Digital Content Protection) compliant device with HDMI or DVI (Digital Visual Interface) input.

C SUPER AUDIO CD indicator (39, 93)

Lights up when: –playing an HD (High Density) layer

of Super Audio CDs.

–no disc i s inserted.

D MULTI CHANNEL indicator (39, 93)

Lights up when:

–playing a disc that contains multiple

audio signal channels.

–no disc is inserted.

E Disc tray (34) F A (open/close) button (34)

G H (play) but ton (34) H X (pause) button (35) I x (stop) button (35) J ./> (previous/next) buttons (46) K PROGRESSIVE button/indicator (22)

Lights up when the player outputs progressive signals.

L Front panel display (12) M Remote sen s or (18) N FL OFF (Front panel display off)

indicator (81)

O VIDEO OFF indicator (34)

* This pl ay er is ba se d on ve r sion 1.1 of High-

Definition Multimedia Interface Specifications.

This DVD player incorporates High-Definition Multimedia Interface (HDMI ™ ) te c hnol ogy.

HDMI, the HDMI logo and High-Defini tion Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

,continued

Front panel display

When playing back a DVD VIDEO/DVD- RW

Disc type

Lights up during Repeat Play (43)

Playing status

Current audio signal (54)

Lights up when you can change the angle (58)

Current title/chapter or playing time (50)

When playing back a VIDEO CD with Playback Control (PBC) (40)

Disc type

Playing status

Lights up during A-B Repeat Play (44)

Current scene or playing ti me (50)

When playing back a Super Audio CD, CD, DATA CD (MP3 audio), or VIDEO CD (without PBC)

Playing status

Lights up dur i ng Repeat Play (43)

Current track (50)

Disc type*

* When playing the HD lay er of Sup er Audi o CDs, the disc type is not displayed.

z Hint

You can adjust the lighting of the front pan el display by setting “DISPLAY” in “CUSTOM SETUP.” (page 81)

Lights up when playing MP3 audio tracks (62)

Playing time (50)

Rear panel

OPTICAL FRONTCOAXIAL

DIGITAL OUT

HDMI OUT

5.1CH OUTPUT

REAR CENTER

WOOFER

R-AUDIO-L

LINE OUT

VIDEO Y

121

S VIDEO

OUT

PRPB

COMPONENT VIDEO OUT

CONTROL S

A DIGITAL OUT (COAXIAL) jack (26)

(27) (28)

B DIGITAL OUT (OPTICAL) jack (26)

(27) (28)

C 5.1CH OUTPUT jacks (28) D LINE OUT L/R (AUDIO) 1/2 jacks

(25) (26) (27)

E LINE OUT (VIDEO) 1/2 jack (19)

F S VIDEO OUT 1/2 jack (19) G COMPONENT VIDEO OUT jack (19)

(Y, PB, PR) or (Y, PB/CB, P R/CR)

H CONTROL S IN jack (19) (U.S./

Canadian models on ly)

I HDMI OUT (high-definition

multimedia interface out) jack (19)

,continued

Remote

A TV/DVD switch (75)

Z OPEN/CLOSE button (35)

B C Number buttons (37)

The number 5 button has a tactile dot.*

D CLEAR button (41) E SUBTITLE button (58) F AUDIO button (53) G REPEAT button (43) H SHUFFLE button (42) I SA-CD MULTI/2CH (Super Audio

CD multi/2 channel) button (39)

J SA-CD/CD (Super Audio CD/CD)

button (39)

K ./> PREV/NEXT buttons (35)

L m/M SCAN/SLOW

buttons (47)

M H PLAY button (34)

The H button has a t actile dot.*

N X PAUSE button (35) O C/X/x/c buttons (37) P DISPLAY button (15) Q TOP MENU button (37) R [/1 (on/standby) button (34) S VOL (volume) +/– buttons (75)

The + button has a t actile dot.*

T TV/VIDEO/TIME/TEXT button (50) U PICTURE MODE button (59) V ENTER button (74) W ANGLE button (58) X SUR (surr ound) button ( 54) Y VIDEO ON/OFF (34) Z SEARCH MODE button (47)

wj ALBUM +/– button

(35, 64)

wk PICTURE NAVI (picture navigation)

button (49, 65 )

wl ZOOM button (35, 65) e; INSTANT ADVANCE/STEP

button (35, 47 )

ea INSTANT REPLAY/STEP

button (35, 47 )

es x STOP button (35) ed ENTER button (30) ef O RETURN button (35) eg MENU button (37) (63)

* Use the tactile dot as a reference when operatin g

the player.

Guide to the Control Menu Display

Use the Control Menu to select a function and to view related information. Press DISPLAY repeatedly to turn on or change the Control Menu display as fol lo w s :

Control Menu display 1

Control Menu display

The Control Menu display 1 and 2 will show di fferent items depending on the disc type . Fo r details about each item, see the pages in parent heses.

Example: Control Menu display 1 when playing a DVD VIDEO.

Control Menu display 2 (DATA CDs only)

Control Menu display off

Control Menu items

1 2 ( 2 7 1 8 ( 3 4 T

Selected item

Function name of selected Control Menu item

Operation message

*1Displays the scene number for VIDEO CDs

(PBC is on), track number for VIDEO CDs/ Super Audio CDs/CDs, album number for DATA CDs.

Displays the index number for VIDEO CDs/

Super Audio CDs, MP3 audio track number or JPEG image file number for DATA CDs.

Displays Super VCD as “SVCD.”

Displays the date for JPEG fi le s.

PROGRAM

1 : 3 2 : 5 5

OFF OFF SET ON

Currently playing chapter number* Currently playing title number * Total number of titles*

Total number of chapters*

) )

ENTER DISPLAY

Quit:

PLAY DVD VIDEO

Playback status (N Playback,

X Pause, x Stop, etc.)

Type of disc being played*

Playing time* Current setting

Options

To turn off the display

Press DISPLAY.

,continued

List of Control Menu items

Item Item Name, Function, Relevant Disc Type

TITLE (page 47)/SCENE (page 47)/TRACK (page 47)

Selects the title, scene, or track to be played.

CHAPTER (page 47)/INDEX (page 47)

Selects the chapter or index to be played.

TRACK (page 47)

Selects the track to be played.

ORIGINAL/PLAY LIST (page 38)

Selects the type of titles (DVD-RW) to be played, the ORIGINAL one, or an edited PLAY LIST.

TIME/TEXT (page 47)

Checks the elapsed time and the remaining playback time. Input the time code for picture and music searching. Displays the DVD/Super Audio CD/CD text, or the DATA CD track name.

MULTI/2CH (page 39)

Selects the playback area on Super Audio CDs when available.

PROGRAM (page 41)

Selects the title, chapte r, or trac k t o pla y in the order you want.

SHUFFLE (page 42)

Plays the title, chapter, or track in random order.

REPEAT (page 43)

Plays the entire disc (all titles/all tracks/all albums) repeatedly or one title/chapter/track/ album repeated ly .

A-B REPEAT (page 44)

Specifies the parts you want to pla y re peatedly.

SHARPNESS (page 60)

Exaggerates the outline of the image to produce a sharper picture.

AV ALIGNMENT (page 61)

Adjust the delay between the pic tu re and sound.

PARENTAL CONTROL (page 70)

Set to prohibit playback on this player.

SETUP (page 77)

QUICK Setup (page 30) Use Quick Setup to choose the desired language of the on-screen display, the aspect ratio of the TV, the audio output signal, and the size of the speaker you are using. CUSTOM Setup In addition to the Quick Setup settin g, you can adj u st va ri o us oth er sett in gs. RESET Returns the settings in “SETUP” to the default setting.

ALBUM (page 62)

Selects the al bum to be played.

FILE (page 47)

Selects the JPEG image file to be played.

DATE (page 65)

Displays the date the picture was ta ke n by a digi ta l cam e ra.

INTERVAL (page 68)

Specifies the duration for which the slides are displayed on the screen.

EFFECT (page 68)

Selects the effects to be used for changing slides during a slide show.

MODE (MP3, JPEG) (page 67)

Selects the data type; MP3 audio track (AUDIO), JPEG image file (IMAGE) or both (AUTO) to be played when playing a DATA CD.

z Hint

The Control Menu icon indicator lights up in green

except “OFF.” (“PROGRAM,” “SHUFFLE,” “REPEAT,” “A-B REPEAT,” “SHARPNESS” only). The “ORIGINAL/PLAY LIST” indicator lights up in green when you select “PLAY LIST” (default setting). The “MULTI/2CH” indicator lights up in green when you select the multi-channel playback area on a Super Audio CD. The “AV ALIGNMENT” indicator lights up in green when set to more than 0 ms.

when you select any item

Hookups

Hooking Up the Player

Follow steps 1 to 6 to hoo k up and adjust the setti ngs of the player.

Notes

• Plug cords securely to prevent unwanted noise.

• Refer to the instructions supplied with the components to be connected.

• You cannot connect this playe r to a TV that do es not ha ve a vide o input jack.

• Be sure to disconnect the power cord of each compone nt before connecting.

Step 1: Unpacking

Check that you have the following items:

• Audio/Video cord (pinplug × 3 y pinplug × 3) (1)

• Remote commander (remote) (1)

• Size AA (R6) batteries (2)

Step 2: Inserting Batteries Into the Remote

You can control the player using the supplied remote. Insert two Size AA (R6) batteries by matching the 3 and # ends on the batteries to the markings inside the compartment. When using the remote, point it at the remote sensor on the player.

Notes

• Do not leave the remote in an extremely hot or humid place.

• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.

• Do not expose the remote sensor to direct light from the sun or a lighting apparatus. Doing so may cause a malfunction.

• If you do not use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion.

Step 3: Connecting the Video/HDMI Cords

Connect th is player to your TV moni tor, pr ojector, or AV ampl ifier ( receive r) using a video cord. Select one of the patter ns A through D, according to the in put jack on y o ur TV moni tor, projector, or AV amplifier (receiver). In order to view progressive signal “480p (525p)” pictures with a compatible TV, proj ect or, or monitor, you m ust us e patt er n B. Select pa tte rn A when connecting to a TV, projector, or AV amplifier (rece iv er) equipped with HD MI input.

Hookups

INPUT

VIDEO

AUDIO

TV, projector, or AV amplifier (receiver)

to LINE OUT (VIDEO) 1 or 2

to HDMI OUT

HDMI cord (not supplied)

TV, projector, or AV amplifier (receiver)

Audio/video cord (supplied)

DIGITAL OUT

HDMI OUT

OPTICAL FRONTCOAXIAL

REAR CENTER

R-AUDIO-L

WOOFER

5.1CH OUTPUT

LINE OUT

(green)

to COMPONENT VIDEO OUT

S VIDEO cord (not supplied)

(yellow)

VIDEO Y

121

COMPONENT VIDEO OUT

S VIDEO

OUT

(blue)

TV, projector, or AV amplifier (receiver)

to S VIDEO OUT 1 or 2

PRPB

CONTROL S

(red)

INPUT

S VIDEO

CD/DVD player

to CONTROL S IN (page 21) (U.S./ Canadian models only)

CONTOL S cord (not supplied)

COMPONENT

VIDEO IN

(green)

(blue)

(red)

TV, projector, or AV amplifier

(receiver)

l : Signal flow

Component video cord (not supplied)

S-LINK

CONTROL S

TV or other eq ui p m e nt with a CONTROL S jack

,continued

A If you are connecting to an HDMI/DVI input jack

Use a certified HDMI cord (not supplied) to enjoy high quality digital picture and sound through the HDMI OUT jack. Note that Super Au dio CD sound is not output fr om the HDMI OUT jac k.

To connect to a TV with DVI input

Use an HDMI-DV I converter cord (not su pplied). The DVI jack w i ll not accept any audio signals, so you ha ve t o use another audio co nnection in addition to this connection (page 23). Furthermore, you cannot connect the HDMI OUT jack to DVI jacks that are not HDCP compliant (e.g., DVI jacks on PC displays).

B If you are connecting to a monitor, projector, or AV amplifier

(receiver) having component video input jacks (Y, P

R/CR)

Connect the component via the COMPONEN T VIDEO OUT jacks us in g a component video cord (not suppl ie d) or three video cords (not supplied) of the same kind and length. You will enjoy accurate col or reproduction and high quality ima ges. If your TV accepts progressive 480p (525p) format signa ls *, use this connection and press the PROGRESSIVE button on the front panel to output progressive signals. For details, see “Using the PROGRESSIVE button” (page 22).

B, PR or Y, PB/CB,

Green

Blue

Red

* The active num ber of pro gr es sive scan lines is 480, and the measured numbe r of lines is 525.

Green Blue Red

C If you are connecting to a video input jack

Connect the yellow plug of an audio/video cord (supplied) to the yellow (video) jack. You will enjoy standard quality images. With this connection, select “NORMAL (INTERLACE)” (default) by pressing the PROGRESSIVE button on t he front panel.

Yellow

White (L)

Red (R)

Yellow White (L) Red (R)

D If you are connecting to an S VIDEO input jack

Connect an S VIDEO cord (not supplied). You will enjoy high quality images. With this connection, select “NORMAL (INTERLACE)” (default) by pressing the PROGRESSIVE button on the front panel.

When connecting to a wide screen TV

Depending on the disc, the image may not fit your TV screen. To change the aspect ratio, see page 79.

z Hint

• For U.S./Canadian models

If your TV has a CONTROL S jack, you can control the player by operating the remote toward the TV. This feature is convenient when you placed the play er an d the TV away from eac h othe r . Afte r connecting the player with other components according to the above A, B, C or D, connect the TV via the C ONTROL S IN jack using a control S cord (not supplied). Refer to the instructions supplied with the TV to be connected. Note that your TV’s input will not automa tically switch to this player when you play a disc.

Notes

• Do not connect a VCR, etc., between your TV and th e playe r . If you pas s the pla ye r signa ls via the VCR, you may not receive a clear image on the TV screen. If your TV ha s only one audio/video input jack, connect the player to thi s ja ck .

VCR

Hookups

CD/DVD player

Connect directly

• Consumers should note that not all high definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In case of 480 (525) progressive scan picture problems, it is recommended that the user swit ch the connection to the ‘standard definition’ output. If there are questions regarding your TV set compatibility with this 480p (525p) DVD player model, please contact our customer service center.

• If the picture appears too white when you are using C or D connection, set “BLACK LEVEL” in “SCREEN SETUP” to “OFF” (page 80).

,continued

Using the PROGRESSIVE button

By using the PROGRESSIVE button on the front panel, you can select the signal format in which the player outputs video signals (Progressive or Interlace), and the conversion method for progressive signals. The PROGRESSIVE indicator lights up when the player outputs progressive s ig nals. Each time you press PROGRESSIVE, the display changes as follows:

PROGRESSIVE AUTO

PROGRESSIVE VIDEO

NORMAL (INTERLACE)

◆PROGRESSIVE AUTO

Select th is setting when: –your TV accepts prog ressive signals, and, –the TV is connected to the COMPONENT VIDEO OUT jacks. Normally select this under the above condition. This automatically detects the software type, and selects the appropriate conversion m ethod. Note that the picture will not be clear or no picture will appear if you select these settings when either of the above conditions is not met.

◆PROGRESSIVE VIDEO

Select th is setting when: –your TV accepts prog ressive signals, and, –the TV is connected to the COMPONENT VIDEO OUT jacks, and –you want to fix the conversion method to PROGRESSIVE VIDEO for video-based software. Select this if the image is no t c lear when you selec t PROGRE SSIVE AUTO. Note that the picture will not be clear or no picture will appear if you select these settings when either of the above conditions is not met.

◆NORMAL (INTERLACE)

Select th is setting when: – your TV does not acc ept progressive sign a ls , or, – your TV is connected to jacks other than the COMPONENT VIDEO OUT jacks (LINE OUT (VIDEO) or S VIDEO OUT).

About DVD software types and the conver sion method

DVD software can be divided into two types: film-based software and video based software. Video-based software is derived from TV, such as dramas and sit-coms, and displays images at 30 frames/60 fiel ds per second. Film -based software is derived from film an d di splays images at 24 frames per second. Some DVD software contains both video and film. In order for the se images to appea r na tural on your screen when output in progressive format, the progressive signals need to be converted to match the type of DVD software that you are watching.

Note

When you play video-based software in pr ogre ssive signal format, sections of some type s of images may appear unnatural due to the conversion process when output through the COMPONENT VIDEO OUT jacks. Images from the S VI DEO OUT 1/2 and LINE OUT (VIDEO) 1/2 jacks are unaffect ed as they are output in the normal (interlace) format.

Step 4: Connecting the Audio Cords

Refer to the chart bel ow to select th e connectio n that be st suits your syst em. Be sure to also rea d the instructions for the components you wish to connect.

Select a connection

Select one of the follow i ng connections, through .

Components to be connected Connection Your setup (example)

• Surround effects: – TVS DYNAMIC (page 54) – TVS WIDE (page 54)

A D

(page 25)

Hookups

Stereo amplifier (receiver)

• Surround effects: – TVS STANDARD (page 54)

MD deck/DAT deck

• Surround effects: – TVS STANDARD (page 54)

AV amplifier (receiver ) having a Dolby Surround (Pro Logic) decoder speakers

• Surround effects: – Dolby Surround (Pro Logi c) ( page 91)

AV amplifier (receiver) with 5.1 ch input jacks and 4 to 6 speakers

• Surround effects: – Dolby Digital ( 5.1 ch) ( page 91) – DTS (5.1 ch) (page 91) – Super Audio CD Multi channel (page 91)

AV amplifier (receiver) with digital input jacks having a Dolby Digital or DTS*2 decoder and 6 speakers

• Surround effects: – Dolby Digital ( 5.1 ch) (p age 91) – DTS (5.1 ch) (page 91)

and 2 speakers

and 3 to 6

(page 26)

(page 27)

(page 28)

,continued

z Hint

If you connect an AV amplifier (receiver) that conforms to the 96 kHz sampling frequency, use connection .

Manufactured under license from Dolby

Laboratories. “Dolby,” “Pro Logic,” and the double-D symbol are trademarks of Dolby Laboratories.

Manufactured under license from Digital Theater

Systems, Inc. U.S. Pat. No’s. 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535 and other U.S. and worldwide patents issued and pending. “DTS ” and “DTS Digital Surround” are registe r e d trademarks of Digital Theater Systems, Inc. Copyright 1996, 2003 Digital Theater Systems, Inc. All Rights Rese r ved.

Connecting to your TV

This connection w i ll use your TV’s spea kers for sound.

CD/DVD player

OPTICAL FRONTCOAXIAL

REAR CENTER

R-AUDIO-L

DIGITAL OUT

HDMI OUT

5.1CH OUTPUT

VIDEO Y

121

WOOFER

LINE OUT

S VIDEO

OUT

PRPB

COMPONENT VIDEO OUT

CONTROL S

R-AUDIO-L

VIDEO

(yellow)*

Hookups

(white)

(red)

LINE OUT

to LINE OUT L/R (AUDIO) 1or 2

l: Signal flow

* The yellow plug is used for vide o si gna ls ( pa ge

19).

z Hint

When connecting to a monaural TV, use a stereomono conversion cord (not supp li ed). Connect the LINE OUT L/R (AUDIO) 1/2 jacks to the TV’s audio input jack.

Audio/video cord (supplied)

(white)

(red)

to audio input

,continued

Connecting to a stereo amplifier ( receiver) and 2 speakers/C onnecting to

an MD deck or DAT deck

If the stereo amplifier (receiver) has audio input jacks L and R only, use . If the amplifier (receiver) has a digital input jack, or when connecting to an MD deck or DAT deck, use . In this case, you can also connect the player directly to the MD deck or DAT deck without using your stereo amplifier (receiver).

CD/DVD player

OPTICAL FRONTCOAXIAL

REAR CENTER

R-AUDIO-L

B-2

VIDEO Y

121

WOOFER

LINE OUT

DIGITAL OUT

HDMI OUT

5.1CH OUTPUT

Optical dig ital cord (not suppli e d) Remove jack cap before connecting

OPTICALCOAXIAL

S VIDEO

OUT

PRPB

COMPONENT VIDEO OUT

CONTROL S

(red)

B-1

R-AUDIO-L

B-2

B-1

VIDEO

DIGITAL OUT

to DIGITAL OUT (COAXIAL or OPTICAL)

Coaxial digital cord (not supplied)

to coaxial or optical digital input

[Speakers]

Stereo amplifier (receiver)

Front (L)

Front (R)

l: Signal flow

Note

Super Audio CD audio signals are not output from the DIGITAL OUT (COAXIAL or OPTICAL)/ HDMI OUT jacks.

(white)

LINE OUT

to LINE OUT L/R (AUDIO) 1 or 2 Stereo audio cord (not supplied)

(red)

to audio input

MD deck/DAT deck

Connecting to an AV amplifier (receiver) having a Dolby Surround (Pro

Logic) decoder and 3 to 6 speakers

You can enjoy Dolby Surround effects only when playing Dolby Surround audio or multichannel audio (D ol by D igital) discs. If your amplifier (receiver) has L and R audio input jacks only, use . If your amplifier (receiver) has a di gital input jack, use .

CD/DVD player

OPTICAL FRONTCOAXIAL

REAR CENTER

C-2

DIGITAL OUT

HDMI OUT

OPTICALCOAXIAL

WOOFER

5.1CH OUTPUT

Optical digital cord (not suppli e d) Remove jack cap before connecting

R-AUDIO-L

LINE OUT

C-2

VIDEO Y

121

S VIDEO

OUT

PRPB

COMPONENT VIDEO OUT

CONTROL S

(red)

C-1

R-AUDIO-L

C-1

VIDEO

Hookups

DIGITAL OUT

to DIGITAL OUT (COAXIAL or OPTICAL)

Coaxial digital cord (not supplied)

to coaxial or optical digital input

[Speakers]

Amplifier (receiver) with Dolby Surround decoder

Rear (L)

Rear (R)

Subwoofer

Center

l: Signal flow

Notes

• When connecting 6 speakers, repl ace th e monaural rear speaker with a center spea ke r, 2 rear speakers and a subwoofer.

• Super Audio CD audio signals are not output from the DIGITAL OUT (COAXIAL or OPTICAL)/ HDMI OUT jacks.

(white)

LINE OUT

to LINE OUT L/R (AUDIO) 1 or 2

Stereo audio cord (not supplied)

(red)

to audio input

[Speakers]

Rear (mono)

Front (R)Front (L)

,continued

Connecting to an AV amplifier (receiver) w ith 5 .1 ch inpu t ja cks and /or a

digital input jack and 4 to 6 speakers

If your AV ampli fier (receiver) has 5. 1 channel inputs, use . If you want to u se t he Do lb y Di gi tal , o r DTS d ec ode r fu nc tio n on y our AV a mpli fi er (r ecei ve r), connect to its digital jack using . With the following connection s, you can enjoy a more

D-2

realistic audio presence in the comfort of your own home.

CD/DVD player

OPTICAL FRONTCOAXIAL

REAR CENTER

R-AUDIO-L

D-2

DIGITAL OUT

HDMI OUT

HDMI cord (not suppli e d)

DIGITAL OUT

5.1CH OUTPUT

HDMI OUT

OPTICALCOAXIAL

Coaxial digital cord (not supplied)

VIDEO Y

121

WOOFER

LINE OUT

to DIGITAL OUT (COAXIAL or OPTICAL)/ HDMI OUT

PRPB

COMPONENT VIDEO OUT

S VIDEO

OUT

Optical digital cord (not supplied) Remove jack cap before connecting

Stereo audio cord (not supplied)

CONTROL S

to 5.1CH OUTPUT

D-1

FRONT

5.1CH OUTPUT

D-1

REAR CENTER

WOOFER

Center

l: Signal flow

to coaxial or optical/ HDMI digital input

[Speakers]

Subwoofer

AV amplifier (receiver) havin g

5.1 ch inputs or/and a decoder

Monaural audio cord (not supplied)

to audio input

[Speakers]

Front (L)

Front (R)

Rear (L)

Rear (R)

: Connecting to the 5.1ch input jacks

D-1

You can enjoy 5.1ch surround sound using the inter n al Dolby Digital, DTS, or Super Audio CD Multi decoder of this player.

: Connecting to a digital input jack

D-2

This connection will allow you to use the Dolby Digital, or D T S decoder function of your AV amplifier (receiver). You are not able to enjoy the surround sound effects of this player.

z Hints

• For connection For correct speaker lo cation, refer to the operating instructions of the connected components.

• To enhance the sound performanc e:

– Use h ig h-perfor mance speakers. – Use front, rear, and center speakers of the same

size and performance.

– Place the subw oof er be twe e n the le ft and right

front speakers.

D-2

Notes

For connection

• After you have completed the connection, be sure to set “DOLBY DIGITAL” to “DOLBY DIGITAL” and “DTS” to “DTS” in Quick Setup (page 30).

• When you connect an amplifier (receiver) that conforms to the 96 kHz sam pli ng f reque nc y, se t “48kHz/96kHz PCM” in “AUDIO SETUP” to “96kHz/24bit” (page 84).

• Super Audio CD audio signals are not output from the DIGITAL OUT (COAXIAL or OPTICAL)/ HDMI OUT jack.

• When you connect the play er to an AV ampl i f i er (receiver) using an HDMI cord, you will need to do one of the following:

– Connect the AV amplifier (receiver) to the TV

with the HDMI cord.

– Connect the player to the TV with a video cord

other than HDMI cord (component video cord, S VIDEO cord, or audio/video cord).

D-2

Hookups

Step 5: Connecting the Power Cord

Plug the player and TV power cords into an AC outlet.

Step 6: Quick Setu p

Follow the steps below to make the minimum number o f basic adju stmen ts for using the pl ayer. To skip an adjustment, press >. To return to the previous adjustment, press .. The on-screen displays differ depen ding on the player model. U.S./Canadi an models are used for illustration unless otherwi se specified.

"/1

./>

1 Turn on the TV. 2 Press [/1. 3 Switch the input selector on your

TV so that the signal from the player appears on the TV screen.

“Press [ENTER] to run QUICK SETUP” appears at the bottom of t he screen. If this message does not appear, select “QUICK” under “SETUP” in the Control Menu to run Quick Setup (page 78).

X/x

ENTER

4 Press ENTER without inserting a

disc.

The Setup Display for selecting the language used in the on-screen display appears.

LANGUAGE SETUP

OSD: MENU: AUDIO: SUBTITLE:

ENGLISH ENGLISH

FRENCH

SPANISH

PORTUGUESE

5 Press X/x to select a language.

The player displays the menu and subtitles in the selected language.

+ 70 hidden pages