Sony CXA3095N Datasheet
– 1 –
CXA3095N
24 pin SSOP (Plastic)
E95Y07-ST
All Band TV Tuner IC (VHF-CATV-UHF)
Description
The CXA3095N is a single chip TV tuner IC which
performs as an oscillator, mixer for VHF-CATV and
UHF bands. An IF amplifier is also provided.
This IC adopts a 24-pin SSOP package (0.8mm
pitch) in response to the trend toward miniaturizing
the tuner and automatic IC mounting.
This IC is the inverted product of the CXA3025N
pin assignment.
Features
• Low noise figure
• Superior cross modulation
• Low spurious
• Stable oscillating characteristics
• Local oscillator output for PLL
• Double tune filter connectable to MIX output
• Low thermal resistance package
Structure
Bipolar silicon monolithic IC
Applications
• TV tuner
• CATV tuner
• VCR tuner
Block Diagram and Pin Configuration (Top View)
Absolute Maximum Ratings
• Supply voltage VCC 10.5 V
• Storage temperature Tstg –65 to +150 °C
• Allowable power dissipation
PD 1200 mW
(when mounted on a board)
Operating Conditions
• Supply voltage VCC 9.0 ± 0.9 V
• Operating temperature Topr –20 to +75 °C
IFOUT
BANDSW
PLLOUT
UOSCB2
UOSCE2
GND
GND
UOSCE1
UOSCB1
VOSCC
NC
VOSCB
IFIN1
IFIN2
V
CC
MIXOUT1
MIXOUT2
GND
GND
VHFIN1
VHFIN2
NC
UHFIN1
UHFIN2
OSC
BUFF
UHF
OSC
VHF
OSC
UHF
MIX
VHF
MIX
REG IF AMP
BAND
SW
13
14
15
16
17
18
19
20
21
22
23
24
2
3
4
5
6
7
8
9
10
11
12
1
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by
any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the
operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
– 2 –
CXA3095N
Pin Description and Equivalent Circuit
Pin
NO.
Symbol
Pin voltage
typ (V)
Equivalent circuit Description
IF output.
Band switching. UHF operation
when 3V or more voltage is
applied externally, and VHF
operation when OPEN or 0.5V
or less voltage is applied.
PLL oscillator signal output.
UHF oscillator.
VHF oscillator.
No connected.
1 IFOUT
Under VHF
operation:
4.5
Under UHF
operation:
4.5
0
3
5.8
5.7
3.5
3.3
3.0
2.5
3.0
2.5
3.5
3.3
6.3
9.0
3.3
3.5
BANDSW
PLLOUT
UOSCB2
UOSCE2
UOSCE1
UOSCB1
VOSCC
VOSCB
NC
2
3
4
5
8
9
10
12
11
1
22
V
CC
47
2
VCC
900
1.6k
20k
22
VCC
3.2k
3
22
30
3k3k
4
5
8
9
3k
1k
10
22
12
3k
VCC
– 3 –
CXA3095N
UHF input.
The balanced input to Pins 13
and 14, or a capacitor is
connected at Pin 13 to GND
and Pin 14 is used for input.
13
14
15
16
17
6, 7
18, 19
20
21
22
23
24
NC
VHFIN2
VHFIN1
GND
MIXOUT2
MIXOUT1
VCC
IFIN2
IFIN1
3.2
3.4
3.2
3.4
0
7.4
7.2
7.4
7.2
9.0
—
—
—
—
No connected.
VHF input.
Normally a capacitor is
connected at Pin 17 to GND
and Pin 16 is used for input.
GND.
Mixer output.
Power supply.
IF amplifier input.
UHFIN2
UHFIN1
3.4
3.2
3.4
3.2
13
14
6k 6k
16
17
6k 6k
20
21
450 450
VCC
22
8k8k
23
24
15p 15p
Pin
NO.
Symbol
Pin voltage
typ (V)
Equivalent circuit Description
– 4 –
CXA3095N
Electrical Characteristics See Electrical Characteristics Measurement Circuit (Ta = 25°C, VCC = 9V)
Item
Circuit current
Conversion
gain
∗1
Noise figure
∗1 ∗2
1% cross
modulation
∗1 ∗3
Max. output
power
Switch ON drift
∗4
+B supply
voltage drift
∗5
PLL OUT output
power
Band switch
voltage
IccV
IccU
CG1
CG2
CG3
CG4
NF1
NF2
NF3
NF4
CM1
CM2
CM3
CM4
Pomax
(sat)
∆fsw1
∆fsw2
∆fsw3
∆fsw4
∆fst1
∆fst2
∆fst3
∆fst4
PoscV
PoscU
VswV
VswU
VHF operation; no signal
UHF operation; no signal
VHF operation; fRF = 55MHz; Input level –40dBm
VHF operation; fRF = 360MHz; Input level –40dBm
UHF operation; fRF = 360MHz; Input level –40dBm
UHF operation; fRF = 800MHz; Input level –40dBm
VHF operation; fRF = 55MHz
VHF operation; fRF = 360MHz
UHF operation; fRF = 360MHz
UHF operation; fRF = 800MHz
VHF operation; fD = 55MHz, fUD = ±12MHz
VHF operation; fD = 360MHz, fUD = ±12MHz
UHF operation; fD = 360MHz, fUD = ±12MHz
UHF operation; fD = 800MHz, fUD = ±12MHz
50Ω load
VHF operation; fosc = 100MHz
VHF operation; fosc = 405MHz
UHF operation; fosc = 405MHz
UHF operation; fosc = 845MHz
VHF operation; fosc = 100MHz
VHF operation; fosc = 405MHz
UHF operation; fosc = 405MHz
UHF operation; fosc = 845MHz
VHF operation; 50Ω load
UHF operation; 50Ω load
VHF operation
UHF operation
38
37
17
18
23
23
99
97
91
89
+8
–20
–20
0
3
53
51
20
21
26
26
13
12
9
9
102
100
94
92
+10
–10
–10
63
62
23
24
29
29
16
15
13
13
±200
±300
±300
±300
±100
±200
±150
±150
0.5
10.5
mA
mA
dB
dB
dB
dB
dB
dB
dB
dB
dBµ
dBµ
dBµ
dBµ
dBm
kHz
kHz
kHz
kHz
kHz
kHz
kHz
kHz
dBm
dBm
V
V
Symbol Conditions Min. Typ. Max. Unit
∗1
Measured value for untuned inputs.
∗2
Noise figure is the direct-reading value of NF meter in DSB.
∗3
Desired signal (fD) input level is –33dBm. Undesired signal (fUD) is 100kHz, 30%AM at ±12MHz.
The measurement value is undesired signal level, it measured with a spectrum analyzer at S/I = 46dB.
∗4
Frequency variation form 3 seconds to 3 minutes after switch ON.
∗5
Frequency variation when Vcc = 9V ± 5% variation.
Loading...