Sony CSDED37, CSDED57, CSDED67 Operating Manual

WARNING

TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

AE!!!5aA

“CAUTION TO REDUCE THE RISK OF

ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.”

Explanation of Graphical Symbols:

Objects and liquid entry - Take care that objects or liquids do not get inside the unit through the ventilation openings.

Carts and stands - When placed or mounted on a stand or cart, the unit should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the unit or cart to overturn or fall.

Condensation - Moisture may form on the CD pickup lens when:

- The unit is moved from a cold spot to a warm spot

- The heating system has just been turned on

- The unit is used in a very humid room

- The unit is cooled by an air conditioner When this unit has condensation inside, it may not function normally. Should this occur, leave the unit for a few hours, then try to operate again.

Wall or ceiling mounting - The unit should not be mounted on a wall or ceiling, unless specified in the Operating Instructions.

~~.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of

●

OWNER’S RECORD

For your convenience, record the model number (you will find it at the bottom of the unit) and serial number (you will find it in the battery compartment) in the space provided below. Please refer to them when you contact your AIWA dealer

‘ode’No ~ ‘erialNO ~

sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

in case of difficulty.

Precautions

Read the Operating Instructions carefully and completely before operating the unit. Be sure to keep the Operating

Instructions for future reference. All warnings and cautions in the Operating Instructions and on the unit should be strictly followed, as well as the safety suggestions below.

Installation

Water and moisture - Do not use this unit near water, such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, swimming pool, or the like.

Heat - Do not use this unit near sources of heat, including heating vents, stoves, or other appliances that generate heat.

It also should not be placed in temperatures less than 5°C (41 “F) or greater than 35°C (95°F). Mounting surface - Place the

Ventilation - The unit should be situated with adequate

space around it so that proper heat ventilation is a&ured. Allow 10 cm (4 in.) clearance from the rear and the top of the unit and 5 cm (2 in.) from each side.

- Do not place the unit on a bed, rug, or similar surface

that may block the ventilation openings.

- Do not install the unit in a bookcase, cabinet, or airtight

rack where ventilation may be impeded.

2 ENGLISH

unit on a flat, even surface.

Electric Power

Power sources - Use on batteries or AC house current,

as specified in the Operating Instructions and marked on the unit.

Polarization - As a safety feature, some units are equipped with polarized AC power plugs which can only be inserted one way into a power outlet. If it is difficult or impossible to insert the AC power plug into an outlet, turn the plug over and try again. If it still does not easily insert into the outlet, please call a qualified service technician to service or replace the outlet. To avoid defeating the safety feature of the polarized plug, do not force it into a power outlet.

AC power cord

- When disconnecting the AC power cord, pull it out by the AC power plug. Do not pull the cord itself.

- Never handle the AC power plug with wet hands, as this could result in fire or shock.

- Power cords should be firmly secured to avoid being bent, pinched, or walked upon. Pay particular attention to the cord from the unit

- Avoid overloading

beyond their capacity, as this could result in fire or shock.

Extension cord - To help prevent electric shock, do not

use a polarized AC power plug with an extension cord, receptacle, or other outlet unless the polarized plug can

be completely inserted to prevent exposure of the blades of the plug. When not in use - Unplug the AC power cord from the

AC outlet or remove all the batteries if the unit will not be used for several months or more. When the cord is plugged in, a small amount of current continues to flow to the unit, even when the power is turned off.

to the power socket.

AC power plugs and extension cords

Maintenance

Clean the unit only as recommended in the Operating Instructions.

Damage Requiring Service

Have the units serviced by a qualified service technician if:

- The AC power cord or plug has been damaged

- Foreign objects or liquid have got inside the unit

- The unit has been exposed to rain or water

- The unit does not seem to operate normally

- The unit exhibits a marked change in performance

- The unit has been dropped, or the cabinet has been damaged

DO NOT ATTEMPT TO SERVICE THE UNIT YOURSELF.

Power Supply

o;2E/BA’j_T/D]R,

OPE/BATT

Remote Control

Insert two R6 (size AA) batteries

* . \~*

(except CSD-ED37)

R6 (AA)

The OPE/BATT/DIR or OPE/BATT indicator lights up while electric current flows to the unit.

to the AC inlet of the unit

supplied AC cord &+ @ to an AC outlet

CAUTION

Use only the supplied AC cord. Use with other cords may

result in the risk of fire.

Open the lid of the battery compartment on the rear and insert eight RI 4 (size C) batteries, not supplied, with the ~

O marks correctly aligned. Then close the lid.

and

To switch from AC power supply to battery power supply, disconnect the AC cord from the AC inlet.

When the reach of the remote control signal is less than 5

meters (16 feet), replace the batteries.

The remote control may not operate correctly when:

- The unit is exposed to intense light, such as direct sunlight

- Objects block the remote control signal to the unit

To use the buttons on the remote control

Buttons on the remote control and the main unit with identical indications have the same functions.

To turn the power on

Press POWER to turn on the display. When using the unit on the batteries, this button will not turn the power on.

To turn the power off

Press POWER to turn off the display. When one of the deck operation buttons is pressed, this button will not turn the Dower off.

To use the FUNCTION button

Each time FUNCTION is pressed while the power is on, the

function is selected cyclically.

CD ~ RADIO ~ *TAPE ~

* applicable when one of the deck operation buttons is pressed

When to replace the batteries

The OPE/BATT/DIR or OPE/BATT indicator becomes dim, the tape speed slows down, volume decreases, or sound is distorted during operation.

Notes on batteries

● Do not mix different types of batteries or old batteries with

new ones.

● When the unit is not to be used for a long period, remove

the batteries to prevent needless battery wear.

● Never recharge the batteries, apply heat to them or take

them apart.

● Remove dead batteries.

If liquid leaks from the batteries, wipe thoroughly to remove.

FUNCTION

POWER —

Unless otherwise noted, the illustrations in the Operating Instructions show the CSD-ED67.

ENGLISH 3

REPEAT/

FM MODE/

Osc

STOPIMEMORY~

– TUNING+

POWER(!)STANDBY

TAPE

H ““’0 I-kL.J

BAND

~ Press *RADIO/BAND repeatedly to select the

desired band.

~FM--+AMT

The power is turned on and the previously tuned station is received. The RADIO indicator lights up. * or BAND on the remote control when the AC cord is connected (except CSD-ED37)

z Press 1+4, BI (+, – TUNING) to select a

station.

During FM stereo reception, ~ is displayed.

After listening, press POWER (!) STANDBY to turn the power off.

For better reception

$% P

Extend the FM antenna and orient it for the best reception.

The AM antenna is inside the unit. Position the unit for the best reception.

For quick tuning

Keep i-,

– TUNING pressed until the tuner starts searching for a station. When a station is tuned to, the search stops.

If the broadcast signal is weak, it does not stop. To stop

the search manually, press -1-or –.

*REPEAT/FM MODE/OSC

- If an FM stereo broadcast contains noise, press the

button so that _ is displayed. Noise is reduced, although reception is monaural. To restore stereo reception, press the button again.

- If a high-pitched sound is heard during

press the button repeatedly until the noise is reduced. Its position can be checked by “*” being

AM recording,

on or off the display.

* or MODE on the remote control (except CSD-ED37)

To change the AM tuning interval

The default setting of the AM tuning interval is 10 kHz/step.

If you use this unit in an area where the frequency allocation system is 9 kHz/step, change the interval as follows. 1 Press RADIO/BAND to display FM. 2 Press

■ while pressing RADIO/BAND to display the

AM frequency. When the AM tuning interval is changed, the preset stations are cleared.

4 ENGLISH

NOTE

unit picks up noise from other electrical appliances

If the

nearby, like a TV or fluorescent lights, move the unit.

You can preset up to 15 stations in each band.

Select a station.

Press *9 STOP/MEMORY once so that “M” is

displayed to store the station.

A station is assigned a preset number, beginning from 1 in consecutive order for each band. “M” may not be displayed if the button is kept pressed for more than 0.5 second.

Preset number

Frequency

* or

■ on the remote control (except CSD-ED37)

Repeat steps 1 and 2.

The next station will not be stored if a total of 15 preset stations have already been stored for a band.

TO listen to preset stations

Select a band then press -11 PLAY/PAUSE/PRESET repeatedly.

- PLAY on the remote control is also available.

To select a preset number directly with the remote control (except CSD-ED37)

Press the numbered buttons O-9 and +1O.

Example: To select number 15, press +10 and 5. To select number 10, press +10 and O.

To clear a preset station

Display the preset number first. Then, press preset number is displayed. The higher numbers in the band are decreased by one,

■ while the

MODE

REPEAT

- PLAY H+, m

■ STOP

Press CD.

The power is turned on and the CD indicator lights up.

Press OPEN to open the disc compartment.

Place a disc with the printed side up and

close the disc compartment.

Total number of tracks and total playing time are displayed.

Press’- II PLAY/PAUSE/PRESET to start

play.

The number of the track being played and elapsed

playing time are displayed. * or F PLAY on the remote control (except CSDED37)

■ STOP/MEMORY – Stops play.

‘>lE PLAY/PAUSE/PRESET – Pauses play. To resume

play, press again. ‘ or II PAUSE on the remote control (except CSDED37)

K+, FM SKIP/SEARCH – Searches for a particular point

during playback. Keep H or release it. – Skips to the beginning of a track. Press 14 or FM repeatedly.

‘REPEAT/FM MODE/OSC – Repeats a single track or all

tracks. Select as follows.

C 1: A single track is played repeatedly. Select a track

with 144 or

C : All tracks are played repeatedly.

* or REPEAT on the remote control (except CSD-ED37)

To start play when the power is off, press CD. The power is turned on and play of the loaded disc begins (Direct Play Function). If you load a disc while the CD indicator flashes in step 2, play starts without pressing -11.

➤>1.

➤Pl pressed and then

To select a track directly with the remote control (except CSD-ED37), press the numbered buttons O-9 and +1O. CD

play starts from the selected track and continues to the last track.

Example: To select number 25, press +10, +10 and 5. To select number 10, press +10 and O.

After listening, press POWER (!) STANDBY to turn the power off.

NOTE

● Do not use irregular shape CDs (example: heart-shaped,

octagonal ones).

It may result in malfunctions.

● Do not place more than one disc in the disc compartment.

● Do not try to open the disc compartment during play.

● Do not touch the lens. Doing so may cause malfunctions.

Up to 30 tracks can be programmed from the disc.

In stop mode, keep’= STOP/MEMORY

pressed until “M” flashes in the display.

‘

or ■ on the remote control (except CSD-ED37)

Press W, >>1 to select a track, then press

H STOP/MEMORY to store it.

Track number

Programmed number

To select a track with the remote control (except CSD-ED37)

Press the numbered buttons O-9 and +1O.

Repeat step 2 to program other tracks.

Press -II to start play.

To check the program, press ~< or ~ in stop mode.

To clear the program, press

“M” disappears in the display.

To change the programmed tracks, clear the program and

repeat all the steps again.

■ once in stop mode so that

ENGLISH 5

POWER(!) STANDBY/TAPE —%

CSD-ED67

OPE/BATT/DIR

(CSD-ED67 only)

Jse Type I (normal) tapes only. XD-ED67 plays the both sides of the tape. >SD-ED57/CSD-ED37 plays the side facing out.

%ess W4 STOP/EJECT to open the cassette holder md insert a tape with the exposed side up.

‘ush the cassette holder to close.

DIR STOP/EJECT

CSD-ED571CSD-ED37

Press +1➤ PLAY or < PLAY while the power is off.

The power is turned on and play of the inserted tape begins.

volume level is displayed during tape operation.

The

-q

WA STOP/EJECT – Stops play. The power will be

automatically turned off.

II PAUSE – Pauses play. To resume play, press again.

M/W~ – Rewinds/fast forwards. To stop the winding,

■\A.

press When the end of a tape is reached, press WA to release

U,w.

The OPEVBATT/DIR indicator – Indicates the playback

side. U: The side facing out (front side) is played.

D: The back side is played.

REVERSE MODE – Selects reverse mode.

~ G (pressed): Plays both sides of the tape once, Play

stops at the end of the reverse side.

1~=) (released): Plays both sides repeatedly.

DIR – Changes play side.

PLAY <REC

-)57=D-ED371 W= STOP/EJECT – Stops play. The power will be

automatically turned off.

II PAUSE – Pauses play. To resume

RE\MIND/+ F FWD – Rewinds/fast forwards. To

stop winding, press

■/4.

play, press again.

6 ENGLISH

Insert a tape with the side to be recorded facing out.

Get ready to record from the

To record from a CD, press CD and load the disc. To record from a radio broadcast, press RADIO/

BAND and tune to a station.

NOTE (CSD-ED67 only) Make sure that ~ of the OPE/BATT/DIR indicator is on. If it is not on, press DIR to turn it on.

Press

4* PLAY or 4 PLAY is pressed simultaneously. When the selected function is CD, CD play and recording starts simultaneously,

For CSD-ED67, REVERSE MODE is also pressed simultaneously. At the end of the tape, it reverses to the back side although recording stops (the deck enters play mode). Press WA STOP/EJECT to stop the tape and press STOP/MEMORY to stop CD play.

To record only the selected tracks of a CD

1 Follow steps 1 to 3 of PROGRAMMED PLAY on page 5

to program tracks.

2 Press

To stop recording, press WA STOP/EJECT. When recording from a CD, play pauses. To stop CD play,

press W STOP/MEMORY.

To pause recording, press II PAUSE. To resume

recording, press again.

To erase recording, press After recording, press POWER (!) STANDBY to turn the

power off.

● REC to start recording,

● REC.

● REC while the power is off.

source.

■

To prevent accidental erasure

Break off the plastic tabs on the cassette tape with a screwdriver or other pointed tool after recording.

To record on the tape again

Cover the tab openings with adhesive tape, etc.

Side A

“OO(! ~

Tab for side A

ENGLISH

REPEAT/FM M“DE/

“’c Iml=ra

3-MODE EQUALIZER —

T-BASS

QSOUND

,,-,====4==,4 ,4

LL—’716

\\..——— ,—

STOP/MEMORY ~

m, w

VOLUME

Press VOLUME A or V. The volume level is displayed

as a number from Oto MAX (25).

● The volume level is automatically set to 14 if the power

is turned off when the volume level is set to 15 or more.

To display the volume level when a function other than TAPE function is selected

Press VOLUME A or V. The volume level is displayed

for 4 seconds.

DISPLAY on the remote control is also available (except CSD-ED37).

3-MODE EQUALIZER

Press * 3-MODE EQUALIZER until one of the indicators lights up. The equalizer mode changes to ROCK, POP, JAZZ or no equalization, cyclically.

ROCK - Emphasizes the high and low range of music. POP - Emphasizes voice and midrange of music.

JAZZ - Emphasizes the low range of music. * or EQ on the remote control (except CSD-ED37)

T-BASS system

The T-BASS system enhances the realism of lowfrequency sound.

Press T-BASS and the T-BASS indicator lights up.

The unit can be turned off automatically at a specified time.

● While CD function is selected, operate the following

procedures in stop mode.

Press REPEAT/FM MODE/OSC ~ while

pressing STOP/MEMORY 13’HW.

If STOP/MEMORY is kept pressed, another operation may start.

Within 4 seconds, press l++ or M to specify

the time until the power is turned off.

Each time it is pressed, the time changes between 10

and 90 minutes in 10-minute steps.

Specified time

To check the time remaining until the power is turned off

Repeat step 1 shown above. The remaining time is displayed for 4 seconds.

While the sleep timer works, the dot keeps flashing.

QSOUND system

This system provides a rich, three dimensional sound area for stereo sources.

You can enjoy more enhanced sound.

Press QSOUND and the QSOUND indicator lights

● At higher volumes, turning QSOUND on may cause

sound distortion. In this case, make the volume down.

To listen with the headphones

Connect headphones with a stereo mini plug to the 0 jack.

up.

8 ENGLISH

To cancel the sleep timer

Display the remaining time and press K or ~

repeatedly until OFF is displayed.

NOTE

If the unit is turned off during tape playback, <- or 4 on

the deck will not be released. Press W= to release

If an erroneous display or malfunction occurs

Make sure that none of the deck operation buttons is

pressed.

■ while pressing POWER 0 STANDBY.

Press

If the unit cannot be reset in the way above, disconnect the AC cord and remove all the batteries to turn off the display. Leave the unit for a while and turn the power back on.

● > or

Maintenance

To clean the cabinet

Use a soft cloth lightly moistened with mild detergent solution. Do not use strong solvents such as alcohol,

benzine or thinner.

To clean the heads

When the tape heads are dirty;

- high frequency sound is not emitted

- the sound is not adequately high

- the sound is off-balance

- the tape cannot be erased

- the tape cannot be recorded on

After every 10 hours of use, clean the tape heads with a

head cleaning cassette. Use separately sold dry-type or wet-type cleaning

cassette.

Refer to the instructions of the cleaning cassette for

details.

To clean the lens

Use a cotton swab slightly moistened with cleaning fluid.

Wipe gently from the center to

the edge.

Lens

ENGLISH 9

+ 19 hidden pages