Sony AVD-V95 User Manual

OPERATING INSTRUCTIONS

MANUAL DE INSTRUCCIONES

MODE D’EMPLOI :

—

For assistance and information

call toll free I-800-BUY-AIW’A

(United States and Puerto Rico)

8Z-AR1 -903-01 99031 5ACK-Y-9

DIGITAL

SURROUND

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

●

RISKOFELECTRICSHOCK

“CAUTION:TO REDUCE THE RISK OF

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

Explanation of Graphical Symbols:

●

DONOTOPEN

- A

ELECTRIC SHOCK,

SERVICE PERSONNEL.”

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alerl the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

●

PRECAUTIONS

Read the Operating Instructions carefully and completely before operating the unit. Be sure to keep the Operating Instructions for future reference. All warnings and cautions in the Operating Instructions and on the unit should be strictly followed, as well as the safety suggestions below.

Installation

Wster and moisture — Do not use this unit near water, such as near a bathtub, washbowl, swimming pool, or the like. Heat — Do not use this unit near heat sources, including

heating vents, stoves, or other appliances that generate heat. It also should not be placed in temperatures less than 5°C (41”F) or higher than 3FPC (95”F). Mounting surface — Place the unit on a flat, even surface.

Ventilation — The unit should be situated with adequate

space around it so that proper heat ventilation is assured. Allow 10 cm (4 in.) clearance from the rear and the top of the unit, and 5 cm (2 in.) from each side.

- Do not place the unit on a bed, rug, or similar surface that may block the ventilation openings.

- Do not install the unit in a bookcase, cabinet, or airtight rack where ventilation may be impeded.

Objects and liquid entry —Take care that objects or liquids do not get inside the unit through the ventilation openings.

Carte and attmde — When placed or mounted on a stand or cart, the unit should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the unit or cart to overturn or fall.

Wafl or ceiling mounting —The unit should not be mounted on a wall or ceiling, unless specified in the Operating

Instructions.

A&*

Owner’s record For your convenience, record the model number and serial number (you will find them on the rear of your unit) in the space provided below. Please refer to them when you contact your Aiwa dealer in case of difficulty.

] Model No.

AV-DV95

Serial No. (Lot No.)

Electric Power

Power sources — Connect this umt only to power sources specified in the Operating Instructions, and as marked on the unit.

Polarization — As a safety feature, some units are equipped with polarized AC power plugs which can only be inserted one way into a power outlet. If it is difficult or impossible to

insert the AC power plug into an outlet, turn the plug over

and try again. If it is not still inserted easily into the outlet,

please call a qualified service technician to service or replace

the outlet. To avoid defeating the safety feature of the

polarized plug, do not force it into a power outlet.

AC power cord

- When disconnecting the AC power cord, pull it out by the AC power plug. Do not pull the cord itself.

- Never handle the AC power plug with wet hands, as this could result in fire or shock.

- Power cords should be firmly secured to avoid being severely bent, pinched, or walked upon. Pay particular attention to the cord from the unit to the power socket.

- Avoid overloading AC power plugs and extension cords

beyond their capacity, as this could result in fire or shock.

Extension cord — To help prevent electric chock, do not use a polarized AC power plug with an extension cord, receptacle, or other outlet unless the polarized plug can De completely inserted to prevent exposure of the blades of the plug.

When not in use — Unplug the AC power cord from the AC power outlet if the unit will not be used for several months or more. When the cord is plugged in, a small amount of current continues to flow to the unit, even when the power is turned off.

1 ENGLISH

Outdoor Antenna

1 Power lines — When connecting an outdoor antenna, make

sure it is located away from power lines.

2 Outdoor antenna grounding — Be sure the antenna system

is properly grounded to provide protection against unexpected voltage surges or static electricity build-up. Article 810 of the National Electrical Code, ANSVNFPA70, provides information on proper grounding of the mast, supporting structure, and the lead-in wire to the antenna discharge unit, as well as the size of the grounding unit, connection to grounding terminals, and requirements for grounding terminals themselves.

Antenna GroundingAccordingto the National ElectricalCode

TABLE OF CONTENTS

PRECAUTIONS ................................................................... 1

PREPARATION!3

CONNECTIONS ..................................................................3

BEFORE OPERATION ........................................................7

SOUND

CUSTOM AUDIO ADJUSTMENT .......................................8

ELECTRONIC GRAPHIC EQUALIZER ...............................9

DSP SURROUND .............................................................. 10

—

(NECART250PARTH)

NEC-NATIONAL ELECTRICAL CODE

Maintenance

Clean the unit only as recommended in the Operating Instructions.

Damaae Requirina Service

Have the unit serviced by a qualified service technician if:

- The AC power cord or plug has been damaged

- Foreign objects or liquid have gotten inside the unit

- The unit has been exposed to rain or water

- The unit does not seem to operate normally

- The unit exhibits a marked change in performance

- The unit has been dropped, or the cabinet has been damaged DO NOT ATTEMPT TO” sEf3VICE THE UNIT YOURSELF. -

BASIC OPERATIONS

SELECTION OF AUDIOAODEO SOURCE

RECORDING AN AUDIO SOURCE .................................12

RADIO RECEPrlON

)

MANUAL TUNIIUG .............................................................

PRESETTING STATIONS ...................o....mm......mmm.............ol4

DOLBY SURRCNJND AND DTS SURROUND

SELECTING DOLBY SURROUND ................................... 15

ADJUSTING DOLBY DIGITAL SURROUND SOUND .....18

SELECTING DTS SURROUND ........................................ 19

REMOTE CONTROL

OPERATING TV, CABLE TV, VCR AND CD PLAYER ......20

...................... 11

—

❑

ON SCREEN DISPLAY

ON SCREEN DISPLAY .....................................................2l

TIMER

SETTING THE CLOCK ......................................r...............2l

SETTING THE SLEEP TIMER .........................................22

GENERAL

SPECIFICATIONS .............................................................23

CARE AND MAINTENANCE .......................................... .

TROUBLESHOOTING GUIDE ..........................................

PARTS INDEX ...................................................................24

—

24 24

Check your unit and accessories

AV-DV95 Stereo receiver Remote control

FM antenna

Operating Instructions, etc.

AM antenna

APPENDIX

ID CODES FOR TV ID CODES FOR CABLE TV

ID CODES FOB VCR ...................................................... A-3

ID CODES FOIR CD PLAYER

..........................................................

m...,,,.......,,,.. ........................

......................................... A-4

ENGLISH

A-1 A-2

CONNECTIONS

Before connecting the AC cord The rated voltage of your unit shown on the rear panel is 120 V AC. Check that the rated voltage matches your local voltage.

CONNECTING EQUIPMENT

Jacks and plugs of the connecting cord are color-coded as follows: Red jacks and plugs : For the right channel of audio signals White jacks and plugs: For the left channel of audio signals Yellow jacks and plugs: For video signals

IMPORTANT Connect the speakers, antennas, and all other external equipment first. Then connect the AC cord at the end.

“ Be sure to connect the VIDEO OUT terminal of a DVD player

directly to aTV set, not through this unit. Otherwise, the picture noise may appear when playing copy protected DVDS.

“2 Input sound through the DIGITAL IN terminals cannot be

recorded. When recording the sound from the DVD, CD, MD or LD player, connect the analog AUDIO OUT terminals of the player to the corresponding AUDIO IN terminals of the receiver.

‘3 When connecting a monaural video, use a stereo-mono

connecting cord (not supplied).

“

When connecting an LD player equipped with the AC-3 RF OUT terminal, use an RF demodulator unit. Also connect the analog AUDIO OUT terminals of the LD player to the receiver to play all the sources. For further information, refer to the instructions of the LD player.

DVD or Video 1*31MD player

to OPTICAL DIGITAL OUT (DVD)

Optical connecting cord

–Coaxial connecting

cord

Optical connecting to OPTICAL

cord

DIGITAL OUT

11~

I ~toAUDIOO”T A

to VIDEO OUT(Video l)”’ -

I ,),,,, .

... .,,,

!..,...,! :;, ,C,,,

!/:11,

-—R

&.=

Insert the plugs fully into the jacks. Loose connections may produce a humming sound or other noise interference.

0)0 m

@m2@ B_Z@; ‘Q~o o

to VIDEO IN

to AUDIO OUTPUT

‘;ll>1:”>i

() <,’ .

..~!), ., , ,~,, ..!,

f’

F&ifEta

o COAXIAL

XGITAL OUT ?F demodulator*4

Video 2*3or

LDWCabie TV

3 ENGLISH

DVD or MD Player

{

(

to VIDEO IN (Video 2)

Optical to OPTICAL DIGITAL OUT

to AUDIO OUT

to AUDIO IN (Video 2) -

connecting ~ ‘

cord

to VIDEO OUT

to LINE IN

Tape deck

IDI 0

@ and@ in the illustration correspond to the following details

@FM antenna

\v/——

@Sub woofer

I 1-

@. Surroundspeakers

@AM antenna

R\aht Left

Q ~j,, @r7

CONNECTING SPEAKERS@)

Speaker terminals Connect front speakers (system A and/or B), a center speaker, surround speakers and sub woofer to the corresponding speaker terminals on the unit:

- the front speaker cords to the FRONT SPEAKERS terminals

- the center speaker cord to the CENTER SPEAKER terminals

- the surround speaker cords to the SURROUND SPEAKERS terminals.

- for more powerful bass, the sub woofer (with a built-in amplifier) cord to the SUPER WOOFER ~ jack When not connecting the sub woofer, be sure to select the “SUBW OFF (sub woofer off) mode (see page 7).

1m*

@Speaker

Front speakers

.- —.— . . - . ..— —..-——————.. —..——— —.

Lift up the terminal flap,

insert the speaker cord lead

into the terminal slot, then close the flap. Check that the cord is connected securely.

Surround speakers

Right

S!/Stem A

Left Right

@Speaker system B

ft+”_

Left

Speaker impedance “ Front and center speakers Use the same Impedance for both the front and center speakers. The SPEAKER IMPEDANCE SELECTOR on the rear should be set to the position that matches the impedance value of the front and center speakers, When using 4 ohm speakers, set the selector to IMP:4Q. When using 8 ohm speakers, set the selector to IMP:8Q. Please unplug the AC cord before setting the selector, . Surround speakers and super woofer The SPEAKER IMPEDANCE SELECTOR has no effect on the SURROUND SPEAKERS terminals and the SUPER WOOFER

4 jack. For the surround speakers and sub woofer, use speakers

of 8 ohms or more.

Connecting + to +, – to - terminals

To get the proper sound effect, the speaker terminals on the unit and the speaker should be connected with proper polarity; the + terminal on the unit should be connected to the + terminal on the speaker (and - to –).

* Be sure to connect the speaker cords correctly as shown in

the illustration on the right column. Improper connections can cause short circuits in the SPEAKER(S) terminals.

● Do not leave objects generating magnetism near the speakers.

—-----x. ‘

SPEAKER— IMPEDANCE SELECTOR

● ,,4

●#

Sub woofer

Center speakel

ENGLISH

POSITIONING THE SPEAKERS

Position the speakers to make the most of the Dolby Digital Surround, Dolby Pro Logic, DTS surround or DSP effect.

@ Front speakers @ Center speaker

Position in the center of the two front speakers. In addition, position on or below the TV set, if connecting a TV set to the unit.

@ Surround speakers

Place the surround speakers directly to the side of or slightly behind the listening area. Align them horizontally, about 1 meter (3.2 feet) above ear height.

@ Sub woofer

Place the sub woofer in any place between the two front speakers. When not connecting the sub woofer, be sure to select the “SUBW OFF (sub woofer off) mode (see page 7).

CONNECTING THE SUPPLIED ANTENNAS @

Connect the FM antenna to the FM 75 Q terminals and the AM

antenna to the AM LOOP terminals.

FM antenna

-Y? antenna

Sound from the surround speakers or center speaker depends on the settina of the DSP, DTS surround, Dolby Pro Logic and Dolby Digital-Surround.

,--%

----,-”.

t m

l-v

l.{

+: ~ k

_————JL–—___”..

“----

,..-

,—%

,------

.-.

To stand the AM loop antenna on a surface

Fix the claw to the slot as shown in the illustration.

To position the antennas

FM feeder antenna: Extend this antenna horizontally in a T shape and fix its ends to the wall. AM loop antenna: Position for the best reception.

● Do not bring the FM antenna near metal objects or curtain rails.

● Do not bring the AM antenna near other external equipment,

the unit itself, the AC power cord or speaker cords, as noise will be picked up.

● Do not unwind the AM loop antenna wire.

5 ENGLISH

CONNECTING AN OUTDOOR ANTENNA

For better FM reception, use of an outdoor antenna is recommended. Connect the outdoor antenna to the terminals.

FM 75 Q

ABOUTTHEREMOTE CONTROL

Inserting batteries

Detach the battery cover on the rear of the remote control and insert two R6 (size AA) batteries.

&(&

R6(AA)

When to replace the batteries

The maximum operational distance between the remote control and the sensor on the unit should be approximately 5 meters (16 feet). When this distance decreases, replace the batteries

with new ones.

Using the remote control

The instructions in this manual refer mainly to the buttons on the main unit, In principle buttons on the remote control with the same names as those on the main unit can be used as well.

● If the unit is not going to be used for an extended period of

time, remove the batteries to prevent possible electrolyte leakage.

● The remote control may not operate correctly when:

- The line of sight between the remote control and the remote sensor in the display window is exposed to intense light, such as direct sunlight.

- Other remote controls are used nearby (those of a television, etc. )

Remote control operation

This remote control system allows you to operate other external equipment besides the AIWA receiver. For details of the remote control operation for other external equipment, see “REMOTE

CONTROIY on page 20. The following is an explanation on how to operate the Aiwa receiver.

RECEIVER/DIGIT

AIWA RECEIVER SET UP

MUTE

POWER

FUNCTION VOLUME

Press the AIWA RECEIVER button to set remote control to the Aiwa receiver mode.

Press one of the buttons indicated above.

FUNCTION button Each time this but!ton is pressed, the sound source changes

cyclically.

TUNER PRESET/SURROUND buttons Tune in the station which has been preset on the receiver. To go to a higher preset number, press the UP>H button, To go to a lower preset number, press the DOWN- button. This button is also used when adjusting the speaker level balance of the DSP, Dolby Pro Logic or Dolby Digital Surround

mode.

TUNER PRESET/

SURROUND

the

It is not necessary to press the AIWA RECEIVER button each time you operate the Aiwa receiver unless another mode has already been set. (See “REMOTE CONTROL’ on page 20.)

If the receiver cannot be operated with the remote control

Follow the steps below using the remote control.

1 Press the AIWA RECEIVER button.

2 Press and hold the SET UP button for about 2.5

seconds.

The indicator on the top of the remote control blinks twice while pressing ithe button.

3 Press the DIIGIT buttons in the order of “4j” “’O”

and “61’

ENGLISH

BEFORE OPERATION

TAPE MONITOR

POWER I

I Eco I UP

PHONES SURROUND

FRONT SPEAKERS A,B

To turn the unit on

Press the POWER button.

Operation is possible after four seconds. The VOL (volume) level or function name is displayed one after the other for the first four seconds. The selected function indicator lights up in red and the others in green.

To change the brightness level of the display

1 Press ECO so that “ECO MODE is displayed.

2 Within 4 seconds, turn the MULTI JOG to display DIM MODE,

and then press the ENTER button within 4 seconds.

3 Within 4 seconds, turn the MULTI JOG to select the dimmer

mode as below, The mode will be automatically set after 4 seconds. It will also be set if the ENTER button is pressed within 4 seconds after step 3.

DIM OFF - DIMMER 1+ DIMMER 2- DIMMER 3

DIM-OFF: The normal display. DIMMER 1: The illumination of the display is dimmer than

DIMMER 2: The illumination of the display is dimmer than

DIMMER 3: The illumination of the display is dimmer than

Using the headphones Connect headphones to the PHONES jack with a standard stereo

plug (06,3 mm, 1/4 inch). Be sure to set the FRONT SPEAKERS A and B buttons to &OFF. Otherwise sound is output from the speakers.

When the headphones are plugged in:

- The Dolby Pro Logic or DSP system is automatically canceled

- The Dolby Digital surround mode or the DTS surround mode is

changed to the “2chSTERE0 (2CH DOWNMIX)” mode

Function indicators

MANUAL SELECT

MULTI JOG

usual.

DIMMER 1.

DIMMER 2. The function indicators turn off.

\_J

To select the front speaker system

To use speaker system A: Set the FRONT SPEAKERS A button to ~ON. To use speaker system B: Set the FRONT SPEAKERS B button to ~ON. To use both speaker systems: Set both the buttons to = ON. Set the button(s) to KOFF to turn off the speaker system(s).

As the front speaker systems A and B are connected in series:

- The sound will decrease slightly when using both speaker systems

- No sound can be heard if the FRONT SPEAKERS A and B buttons are set to wON when only one speaker system is

connected

When not connecting a sub woofer

Be sure to select the “SUBW OFF mode. After pressing the SURROUND button to turn on the Dolby

Pro Logic, press the MANUAL SELECT button on the remote control once so that “SUBW ON” appears on the display. Then press the UP button or turn the MULTI JOG within four seconds to display “SUBW OFF.”

To turn the unit off, press the POWER button.

POWER ECONOMIZING (ECO) MODE

~ PowER &TANDBY/ON indicator

Setting this unit to the ECO mode reduces power consumption as below. Initial setting of the ECO mode is ON.

● When the current time is set, the clock display disappears

immediately.

● While the power is off, all the display lights turn off, and only

the POWER& 3TANDBY/ON indicator lights in red.

To cancel the ECO mode 1

Press the ECO button to display ECO MODE while the unit is

turned on.

Within 4 seconds, press the ENTER button. Within 4 seconds, turn the MULTI JOG to select ECO OFF,

The mode will be automatically set after 4 seconds. It will also be set if the ENTER button is pressed within 4 seconds

after step 3.

7 ENGLISH

CUSTOM AUDIO ADJUSTMENT

CKKxJ CID

00 cx-&

0::0

EGO

!——.——l

I ..TJI--JEU

BALANCE T-BASS

T-BASS

BBE

VOLUME

BBE SYSTEMI

The BBE system enhances the clarity of high-frequency sound.

Press the BBE button. Each time it is pressed, the level changes. Select one of the

three levels, or the off position to suit your preference.

l--cmirTTQ~ ~ :

mmm

r~mirlrimrwz]-- ; : ,

.......

..”..,

..:

:..

~ .!

:,.::

:;.

&l.&”

,:.

-n

VOLUME

Turn the VOLUME control on the unit, or press the VOLUME

buttons on the remote control.

The volume level is shown on the display for four seconds. It can

be adjusted between O and MAX (31). It flashes when set over the level of 21,

The volume level remains memorized even after the power is

turned off, However, if the power is turned off when the volume is set to more than 17, it is automatically set to 16 the next time

the power is turned on.

To adjust the Iefthight balance of the front speakers

Press the BALANCE button to display “L/R OdB”. Then press the DOWN or UP button repeatedly or turn the MULTI JOG within four seconds. Note that the front speaker balance for the Dolby Digital, Dolby Pro Logic and DTS surround modes is also changed.

To mute the sound temporarily Press the MUTING button (–20 dB). “MUTE ON” appears on the display for four seconds. While muting the sound, the selected function indicator flashes. Press the MUTING button again to restore the sound.

CONTROL

● The BBE system is automatically canceled:

- When the DIGITAL (Dolby Digital or DTS) mode is selected

- When the Dolby Pro Logic is turned on

● The BBE system cannot be turned on:

- While the DIGITAL (Dolby Digital or DTS) mode is selected

- While the Dolby Pro Logic is turned on

SUPER T-BASS SYSTEM

The T-BASS syst~!m enhances the realism of low-frequency

sound. Press the T-BASS button.

Each time it is pressed, the level changes. Select one of the

three levels, or the off position to suit your preference.

EmmmmamEml

mmommQR?ac3msr9nm! i

....,;..

::t

,...:... ,.m .!.

: .:

LIzc=l

mm mm mm Umi

(cancel)l

Low-frequency sound may be distorted when the T-BASS system

is used for a disc or tape in which low-frequency sound is

originally emphas~zed. In this case, cancel the T-BASS sysitem.

SOUND ADJUSTMENT DURING RECORDING

The output volume and tone of the speakers or headphones may

be freely varied without affecting the level of the recording.

ENGLI!;H

ELECTRONIC GRAPHIC

EQUALIZER

SETTING NEW EQUALIZATION CURVES

Up to 4 equalization curves can be stored as the manual modes Ml to M4.

GEQ

This unit provides the following five different equalization modes.

ROCK. Powerful sound emphasizing treble and bass POP: More presence in the vocals and midrange

JAZZ: Accented lower frequencies for jazz-type music CLASSIC: Enriched sound with heavy bass and fine treble

BGM: Calm tone with suppressed bass and treble

Press the GEQ (Graphic Equalizer) button, and turn the MULTI JOG until the desired equalization mode is displayed. The GEQ modes are displayed cyclically as follows.

ROCK— POP — JAZZ —

L-

The selected mode name is displayed for four seconds, and the

y4— M3—

,------- Manual mode -------:

CLASSIC — BGM

M2—

➤indicator appears on the left side of the selected mode name.

Selected mode

To cancel the selected mode Press the GEQ button to display the GEQ mode name, and press

the button again within 4 seconds. “GEQ OFF appears on the display.

1 3,6

2 1,5,7

Press the GEQ button and press the ENTER button within 4 seconds.

Press the DOWN or

frequency.

The level indicator of the selected frequency flashes.

Turn the MULTI JOG to adjust the level of the

selected frequency.

Repeat steps 2 and 3 to make the desired

equalization curve.

In steps 2 and 3, the unit returns to normal mode when no

operation is made for about 8 seconds.

Within 8 seconds, press the ENTER button.

“GEQ Ml” appears on the display.

Turn the MULTI JOG to select a preset number

from Ml to M4.

Press the ENTER button.

The equalization curve is stored. The selected preset number and the equalization curve are displayed for a few seconds for each.

UP button to select a

To select with the remote control

Press the GEQ button repeatedly until the desired equalization mode is displayed. Five preset modes, the manual modes GEQ Ml to GEQ M4 and “GEQ OFF can be selected.

9 ENGLISH

To adjust the GEQ curve temporarily Follow the steps from 1 to 4 above. The adjusted GEQ curve

still remains before changing or canceling the GEQ mode,

To select the manual preset curve

Press the GEQ button, and turn the MULTI JOG until the desired

manual preset number is displayed.

DSPSURROUND

urcwJ

DSP

DOWN,UP

The DSP (Digital Signal Processor) surround circuits can recreate

the effect of sounds reflected from walls or ceilings, to obtain the sound presence of real environments. There are four modes with matching graphic equalization modes. Equalization modes are selected automatically and can also be selected or turned off to suit your preference.

Press the DSP button, and turn the MULTI JOG until

the desired DSP mode is displayed. The selected mode name is displayed for four seconds, and the

indicators and matching GEQ mode name.

➤appear on the left sides of the selected DSP name

MULTI JOG

5%CJ

C3R ~:g=

at.=

\ a“

Qo a

MANUAL SELECT

DOWN,UP

To adjust the volume and balance of the surrounld 2,,,,.. speakers

Press the MANUAL !3ELECT button on the remote control three times to display “SUR 0d13°while the DSP system is turned on, Then press the DOWN or UP button repeatedly or turn the MULTI JOG within four seconds.

● The DSP system i:; automatically canceled:

- When the Dolby lPro Logic is turned on

- When the DIGI1-AL (Dolby Digital or DTS) mode except “2chSTERE0 is selected

● The DSP system cannot be turned on:

- While the DIGI1-AL (Dolby Digital or DTS) mode except

“2chSTERE0 is selected

- While the Dolby lPro Logic is turned on

- While headphones are plugged in

~+~;j

Selected DSP mode

Matching GEQ mode

When the music source is monaural

Select LIVE to obtain a simulated stereo effect, When DANCE, HALL or ARENA is selected, no sound will be heard from the surround speakers,

To cancel the selected mode

Press the DSP button to display the DSP mode name, and press

the button again within 4 seconds, “DSP OFF” appears on the

display. Even if canceling the selected DSP mode, the matching or selected GEQ mode still remains.

To select with the remote control

Press the DSP button repeatedly until the desired DSP mode is displayed. Four DSP modes and “DSP OFF can be selected.

ENGLISH10

SELECTION OF AUDIOMDEO SOURCE

FUNCTION

Function indicators

To select the video source

1 Trun the FUNCTION to select PHONO, CD or AUX, 2 Press the ENTER button to display VIDEO 1. 3 Turn the MULTI JOG to select VIDEO 2 or VIDEO 3.

To change a displayed name for the VIDEO 1

and VIDEO 2

When the VIDEO 1 function is selected, VIDEO 1 is displayed initially. It can be changed to DVD or MD. Press the DIGITAUANALOG/BAND button while pressing the ENTER button. The displayed name for the VIDEO 2 function can be changed to VIDEO 2, LD or TV; while the VIDEO 2 function is selected, press the DIGITAL/ANALOG/BAND button while pressing the ENTER button.

DOWN:UP

DIGITAUANALOG/BAND

MULTi JOG

EN+ER

1 Select the program source.

Turn the FUNCTION selector or press the TAPE MONITOR button. The selected function indicator lights in red.

I ComDact disc I Television, etc. I AUX

Video I VIDEO l/DVD/MD.

LD or Cable TV I VIDEO 2/LD/TV

I MD or DVD I VIDEO l/DVD/MD

The function to be selected (except PHONO) depends on the equipment connected to the input terminals on the rear panel of the unit.

To select with the remote control Press the TAPE MONITOR button or the FUNCTION button repeatedly.

I CD

I VIDEO 2/LDiTv, VIDEO 3 I

When using a turntable with a built-in equalizer amplifier, set the switch of the equalizer amplifier to off. See the instructions of the turntable for further information.

2 Start the selected program

3 Adjust the sound,

About the video source to

source.

the monitor or TV

To select the “ANALOG” or “DIGITAL” (Dolby Digital or

1, VIDEO 2 or VIDEO 3 function

Press the DIGITAIJANALOG/BAND button when the CD, VIDEO 1, VIDEO 2 or VIDEO 3 is selected. The selected mode “ANALOG” or “DIGITAL’ appears on the display. In the DIGITAL mode: Equipment connected to the OPTICAL DIGITAL IN terminal is selected as a source for the CD, VIDEO 1 or VIDEO 3 function, and one connected to the COAXIAL DIGITAL IN terminal for the VIDEO 2 function. The DIGITAL

indicator lights in red. In the ANALOG mode: Equipment connected to the CD, VIDEO

l/DVD/MD IN or VIDEO 3 terminals is selected as a source for

the CD, VIDEO 1or VIDEO 3 function, and one connected to the

VIDEO 2/LDiTV terminals for the VIDEO 2 function.

The “DIGITAL’ mode changes to the “ANALOG,” when pressing the TAPE MONITOR button.

When the “OVER LEVEL” indicator lights up

The unit is equipped with the OVER LEVEL indicator. When input analog signals from the connected equipment are too high to accept, the indicator lights on the right side of the display. In this case, adjust the input level as mentioned below so that the indicator disappears.

To adjust the sound level of the connected source The input sensitivity level of each function can be adjusted

(except the TUNER, CD(DIGITAL), VIDEO 1 (DIGITAL), VIDEO

2 (DIGITAL) and VIDEO 3 (DIGITAL) functions).

When the sound level of the connected source is higher or lower than that of the TUNER, adjust it as follows.

1 Select the function to be adjusted.

Turn the FUNCTION or press the TAPE MONITOR button and play the source.

2 Press the UP or

DTS surround) mode of the CD, VIDEO

DOWN button repeatedly.

CEmBmmmcmmm ! : GEmmElmzzl massiamIim , ,

....... ...- ,,... ; , ,

.,..:...

:..%:...:;...: ;

.... .... :...:

U?5iimimi

Selected video source

V1:VIDEO 1,V2:VIDE02,V3:VIDE03

The selected video source is indicated on the display and the video signal through the MONITOR VIDEO OUT jack is output on the TV.

11 ENGUSH

Adjust the level so that the “OVER LEVEL’ indicator does not light on the display.

● The level can be adjusted between -6dB (MIN) and +8dB

(MAX) in 2dB steps. Adjust the level so that the sound is

output at the same level as the TUNER.

● The input sensitivity level of the TAPE MONITOR can be

adjusted to OdB or -6dB.

TO PLAY A DVD OR LD RECORDED DOLBY DIGITAL OR DTS SURROUND

RECORDING AN AUDIO SOURCE ,,,

-:, ,,.

This receiver is equipped with the Dolby Digital decoder DTS decoder, and has the DIGITAL IN (both OPTICAL COAXIAL) terminals. When a DVD or LD player is connected to the DIGITAL IN terminal of the receiver, you can enjoy theaterquality audio right in your home when playing discs recorded Dolby Digital surround or DTS surround,

Before operation

Check that the TAPE MONITOR is not selected. If the TAPE MONITOR is selected, press the TAPE MONITOR button so that “TAPE OFF appears on the display.

Turn the FUNCTION to select the VIDEO 1 (VIDEO 2 or VIDEO 3) and press the DIGITAUANALOG/ BAND button repeatedly until “DIGITAL” is displayed.

cmmcmmxmcx%ml ;

[rmncllmmmxzalmm$m?m ,

;.. ... ... .:. ..... ... .

.. :::.. ,: ;;: : :.. ;...:: :...

.:. :...: .:. : . ::.,..

The DVD (LD) player connected to the OPTICAL (COAXIAL) DIGITAL IN terminal is selected as a source.

Start playing the DVD (LD) recorded in Dolby

tititi

.,.,,,,

and and

Digital surround or DTS surround.

● The “DOLBY DIGITA~ indicator will light on the display when

the bit stream of the Dolby Digital surround comes in the unit.

mmm!ElmmcmEm

m5mmmr3zzam3mrzml : ; .:,

y,..;’- :...: .;

:..: : : :: . . . : :

. .:. :... . . . . . . . . . .:.

To select the Dolby Digital surround mode according to your speakers, see “SELECTING DOLBY SURROUND on page 15,

* The “dts” indicator will light on the display when the bit stream

of the DTS surround comes in the unit.

12z E@cmmmmmm Cmi20nxmmmlzzxmmm

: : .:. ~...:-:-. .: ::: ::... ; :

... .:. ...

1.0,,, mm,u .,.,,..

............ ,:.

‘

. .

immimkmi

Li!mitii!ti

1 ENTER

Select the program source to be recorded.

Turn the FUNCTION.

Set the tape deck or MD recorder to the recording mode.

Start the selected program source.

To monitor recorded sound during recording (when tlhe connected tape deck is a three-head system)

Press the TAPE MONITOR button, “TAPE ON” appears on the display for four seccmds, and then the source name selected in step 1 comes back on, To cancel the tape monitor, press it again so that “TAPE OFF” appears,

●

Any sound control system has no effect on recording (see page 8).

●

Input sound through the DIGITAL IN terminals cannot be recorded. When recording the sound from the DVD, CD, MD or LD player, connect the analog AUDIO OUT terminals of

the player to the corresponding AUDIO IN terminals of Ithe

receiver.

The sound will be recorded in 2 ch stereo.

✎

When recording audio sources by the MD recorder connected to the VIDEO 1/[)VD/MD AUDIO OUT terminals, the selected video source (see page 11) should be V2 m’ V3. Recording cannot be done while the VI (VIDEO 1) is selected and

displayed on the! window.

●

Input sound frcim the tape deck connected to the TAPE

MONITOR IN terminals cannot be recorded.



❑

—

To select the DTS surround mode according to your speakers, see “SELECTING DTS SURROUND” on page 19.

● While the TAPE MONITOR is selected and the TAPE MONITOR

indicator turns red, “DIGITA~ cannot be selected.

● When headphones are plugged in, the Dolby Digital surround

mode or DTS surround mode is automatically changed to “2chSTERE0 and the “2CH DOWN MIX indicator lights on the display. Even if the SURROUND button is pressed while the headphones are plugged in, the mode cannot be changed.

● This unit supports input signals of the Dolby Digital surround

bit stream, DTS surround bit stream and linear PCM whose sampling frequency is 32 kHz, 44,1 kHz and 48 kHz. The unit cannot play the DVDS whose sampling frequency is 96 kHz.

● When connecting some DVD player to the receiver through the

DIGITAL IN terminals, noise maybe heard in the DVD operation: e.g. searching a disc, skipping a chapter.

To play a DTS audio CD There are some audio CDs recorded in DTS surround like

DVDS and LDs.

They will present you with a live-quality audio in your home.

1 Select the CD function. 2 Select the DIGITAL mode (see page 11).

The CD player connected to OPTICAL DIGITAL IN (CID) terminal is selected as a source.

3 Start playing the CD recordea in DTS surround.

To select the DTS surround mode, see page 19.

—

ENGLISH12

MANUAL TUNING

Turn the FUNCTION to select theTUNER function, and press the DIGITAUANALOG/BAND button repeatedly to select the desired band.

The display changes to frequency indications after indicating band and video source (VI, V2 or V3) for two seconds.

Press the UP or DOWN button on the main unit

to select a station.

Each time the button is pressed, the frequency changes. When a station is received, “TUNE” is displayed for two seconds. During FM stereo reception, ll@DIl) is displayed.

MONO

TUNER

Tochange the AM tuning interval

The default setting of the AM tuning interval is 10 kHz/step. If

you use this unit in an area where the frequency allocation system is 9 kHz/step, change the tuning interval. Hold down the DIGITAUANALOG/BAND button and press the POWER button. To reset the interval, repeat this procedure.

Tosearch for a station quickly (Auto Search)

Keep the UP or DOWN button on the main unit pressed until the

tuner starts searching for a station. After tuning in to a station, the search stops. To stop the Auto Search manually, press the UP or DOWN button.

● The Auto Search may not stop at stations with very weak

signals.

When an FM stereo

Press the MONO TUNER button on the remote control so that “MONO appears on the display. Noise is reduced, although reception is monaural.

MONO

To restore stereo reception, press the button so that “STEREO appears.

broadcast contains noise

When the reception contains noise interference

Move the unit away from other electrical appliances, especially digital audio devices, or turn off the appliances that generate noise signals.

13 ENGLISH

PRESETTING STATIONS

CX30C2 ]

.DOWN,UP

I MULTIJOG ~

The unit can store a total of 32 preset stations. When a station is stored, a preset number is assigned to the station. Use the preset number to tune in to a preset station directly.

Turn the FUNCTION to select theTUNER function,

and press the DIGITAL/ANALOG/BAND button repeatedly to select the desired band. Then press

the UP or DOWN button to select a station.

Press the ENTER button on the main unit to store

the station.

A preset number assigned to the station, beginning from 1 in consecutive order for each band, flashes in the display for

PRESET NUMBER TUNING

1 Turn the FUNCTION to select the TUNER function,

and press the DIGITAL/ANALOG/BAND button repeatedly to select a band.

2 Turn the MULTI JOG to select a preset number.

To clear a preset station

Select the preset number of the station to be cleared. Then, press

the ENTER button gm the main unit, and press it again within four seconds. The preset numbers of all other stations in the band with higher

numbers are decreased by one.

When using the remote control

Press UP>Ft or DC)WNM4 button to select a preset number.

Repeat steps 1 and 2.

No more stations will be stored if a total of 32 stations have already been stored for all the bands.

When the AM tuning interval is changed, all preset stations are

cleared. The preset stations have to be set again.

ENGLISH 14

This unit is equipped with the Dolby Pro Logic decoder, Dolby Digital decoder and DTS decorder. The unit and the center and surround speakers (standard) assure full-scale home theater sound. When playing back discs or video software that have been recorded in Dolby Pro Logic, Dolby Digital surround or DTS surround, astonishingly realistic sound surrounds the listener to create a new level of audio/visuai entertainment.

Independent control of the five channels allows the listener to enjoy the same type of sound reproduction experienced in movie theaters. Voices are reproduced in the front and center sound field, while ambient sounds like cars and crowds are reproduced on all sides of the listener for an incredibly lifelike audio/video experience. Please read the following carefully to “tune” the system’s output to match the characteristics of your listening space.

Check the following:

● Before enjoying the DOLBY surround sound or DTS

surround sound, adjuat the speaker sound ievefs to the proper balance (see page 16).

● Make sure the speakers are properly connected and positioned

(see pages 4 and 5).

● Make sure the TV set and video unit are properly connected

(see page 3).

● Make sure the disc and video tape, etc., support Dolby Pro

Logic, Dolby Digital surround or DTS surround.

TO SELECT A DOLBY SURROUND MODE

Preparations

● When selecting a Dolby Digital surround mode, select the

VIDEO 1 (DIGITAL), VIDE02 (DIGITAL) or VIDEO 3 (DIGITAL) function (see page 12),

● When selecting a Dolby Pro Logic mode, select the function

except CD(DIGITAL), VIDEO 1 (DIGITAL), VIDEO 2 (DIGITAL) and VIDEO 3 (DIGITAL).

12Press the SURROUN CD button and turn the

MULTI JOG to select the appropriate mode.

The selected mode name appears on the display.

[Dolby Digital surround]

SELECTING DOLBY SURROUND

The optimal Dolby Digital surround and Dolby Pro Logic modes

and settings depend on the type and placement of the speakers. It is recommended that the optional Aiwa speakers should be

used for all channels, for example, the SX-AVR2700 speaker system. Check the current type and placement of your speakers and select the recommended mode accordingly.

The recommended mode

[Dolby Digital surround]

I Center sDeaker

Larger-size

Surround speaker DOLBY (Rear speaker)

No eurround speaker WIDE

[Dolby Pro Logic]

[

Surround speaker

(Rear s~eaker)

No surround

s~eaker

D-WIDE

3 STEREO-

Lamer-size

PRO LOGIC-

WIDE

3 STEREO-

WIDE

Smaller-size

DOLBY PHANTOM

D-NORMAL

3 STEREO-

NORMAL

Center epeaker

Smaller-size

PRO LOGIC-

NORMAL

3 STEREO-

NORMAL

No speaker

2chSTERE0

No soeaker

PHANTOM

—

Q&)

To select the 2chSTERE0 mode, press the SURROUND

MODE button repeatedly until “2chSTERE0 appears.

[Dolby Pro Logic]

*3 i : “.=..:, :..; . ..........

~PROLOGlC4 PHANTOM ‘3 STERE0 I

Cmcecmmmcm’ml ; : DmEKlcEmmz?llzmm cEm : ; ,

:,., -.,. . :.,, , ;..

:: ::. ,: ..

:: :...

:: ::

...............~...: :

‘

DOLBY D ~

mimc!mmxmckiizml [ :

\r%5ciorFWlr-mznl~@ml , ; ,

.... .... ...

:: :: :

.... .... . . :: :;.. ;:

IW18

:...

Y G+G,T.41J LU.m

PHANTOM ---+ 3 STEREO

: ..... ..... .:. :.... ; ; .

0!3 q

. .:. .....

g? ;;

+;;:

-wig

tirm!%ti

(@jD

Press the SURROUND button again and hold it

down until the center speaker mode to be selected appears. (Except the 2chSTERE0 and PHANTOM

“NORMAL” and “WIDE” appear one after the other.

modes.)

PHANTOM mode: Select this mode when the center speaker is not connected. All center channel signals are redistributed to

the left and right channel speakers. 3 STEREO mode: Select this mode when the surround speakers

are not connected.

15 ENGLISH

When operating with the remote control

Press the SURROUND button repeatedly to select the mode,

and hold it down to select the center speaker mode.

● Depending on the sound source or listening condition, surround

effect may not be obtained even when the Dolby Digital surround or Dolby Pro Logic is selected.

● The full Dolby Digital surround or Dolby Pro Logic effect cannot

be obtained when using software not recorded in the Dolby Digital surround or Dolby Pro Logic system, In this case, use

the DSP surround system instead (see page 10).

● When headphones are plugged in:

- The Dolby Pro Logic system is automatically canceled,

- The Dolby Digital surround mode is automatically changed to “2chSTERE0.”

● While headphones are plugged in:

- The Dolby Pro Logic cannot be turned on.

- The Dolby Digital surround mode cannot be changed.

ADJUSTING SPEAKER LEVEL BALANCE

The unit is equipped with a built-in test signal generator called a

noise sequencer for easy balance adjustment of all five channels. The sequencer outputs a noise signal that “travels” from channel to channel, enabling the simple adjustment of sound level to achieve the same apparent loudness, at your listening position, from each channel,

12Select the Dolby Digital surround (except

“2chSTEREO”) or Dolby Pro Logic mocle according to the current type and placement of

your speakers.

(See page 15,)

Press the MANUAL SELECT button on the remote

control and hold it down for about two seconds

until “U’ of “LJR OdB” starts to flash.

A noise signal is sent to each channel in turn as follows:

DOLBY D (PRO LOGIC) NORMAL or WIDE mode

UR OdB(Left front speaker)*

CEN 0d13(Center speaker)

UR OdB(Right front speaker)*

S-R OdB (Right surround speaker)

S-L OdB (Left surround speaker)

PHANTOM mode

# UR OdB’

l-- S-L odB +– S.R ()(,fB~

3 STEREO NORMAL or WIDE mode

l-+ “i30dB*-+CEN OdB+ M, OdB’---l

—+ L/R OdfY ~

“ “L’ or “R flashes to indicate one of the front speakers from

which the noise signal is output.

Tobe continued

ENGLISH16

3 Adjust the sound level of the center and surround

speakers.

While “CEN,” “S-U’ or “S-R” flashes in the display, press the UP or DOWN button on the remote control so that the sound level of the center or surround speakers matches that of the

front speakers.

The balance of the front speakers can be adjusted as well

while “UR” is displayed.

The UP or DOWN button on the main unit cannot be used.

Press the MANUAL SELECT button again to stop

the noise signaL

To change the delay time of the surround speakers or center speaker when

or Dolby Pro Logic mode While the Dolby Digital surround (except “2chSTEREO) or Dolby

Pro Logic is activated, press the MANUAL SELECT button on the remote control repeatedly so that “CEN OmS” or “SUR 5mS” (SUR 20mS) is displayed. Then, within 4 seconds, press the UP or DOWN button or turn the MULTI JOG. The delay time changes as shown below.

[Center speaker] Adjust the delay time so that lines (voice in a movie) are heard clearly and naturally. The center speaker delay time is initially set to O ms (milliseconds). It can be adjusted between O and 5 ms in 1 ms step.

Cl&

;-~.y-:. :

‘.......... :

using the Dolby Digital surround

122mrBcLmGmGiFiEm CrEmmzimzllxmmmml :

:.,.:..:

... ....

~ ;... :-.. ::::::

.....,,.,,

LMITAL

;

:.;

li&mimi

@j@

When adjusting the speaker level balance of the Dolby Digital surround, that of the Dolby Pro Logic is also changed and vice versa.

About the channels The left and right speakers create the stereo effect. The center spesker helps precise sound positioning over a broad sound field. The rear-mounted surround speakers enhance the “depth” of

the sound field.

[Surround speakers]

Adjust the delay time to suite your preference.

Dolby Digital Surround

The speakers delay time is initially set to 5 ms. It can be adjusted

between Oand 15 ms in 5 ms steps.

Dolby Pro Logic The speakers delay time isinitially set to 20 ms. Itcan be adjusted between 15 and 30 ms in 5 ms steps.

● When adjusting the delay time of the surround speakers or

center speaker for the Dolby Digital surround, that of the Dolby Pro Logic is changed and vice versa.

● When the surround speakers delay time of the Dolby Digital

surround is set to O m’s (5 ms, 10 ‘ms , or 15 ins), that o~the Dolby Pro Logic is set to 15 ms (20 ms, 25 ms or 30 ins), and vice versa.

To adjust the speaker level balance source

The speaker level balance can be changed after adjusting it with the noise sequencer. The balance can be changed whenever

the Dolby Digital surround or Dolby Pro Logic system is activated.

Play a disc or video software recorded in Dolby Pro Logic or Dolby Digital surround.

Press the MANUAL SELECT button on the remote control repeatedly so that “L/R,” “CEN,” “S-U or “S-R” appears on the

display.

Press the UP or DOWN button or turn the MULTI JOG while

the speaker name to be adjusted is displayed,

while listening to the

17 ENGLISH

ADJUSTING DOLBY DIGITAL

SURROUND SOUND

DOWN,UP

ENTER

ADJUSTING DYNAMIC RANGE

Dynamic range of tlhe Dolby Digital surround sound can be ~~~ adjusted, The unit is initially set to the “STD” (standard) mode. pg:~

1 While the Dolby Digital surround is activated,

&#,’

# .4 “-.

fg%

press the ENTER button on the main unit and hold @ it down until “MID NIGHTTHEATER” runs through ~’i on the display.

$] ,“

% ‘a

MULfl JOG

ADJUSTING LOW FREQUENCY SOUND

EFFECT(LFE)

The disc recorded in Dolby Digital surround contains special signals called LFE to enhance low frequency sound effect, The LFE signals are recorded insomeparticular parts on the disc and output from the connected sub-woofer to reproduce astonishingly powerful low sound. The sound level of the LFE signals can be adjusted according to your speakers connected while the Dolby Digital surround is activated.

1 Press the UP or DOWN button and hold it down

until “LFE” is displayed.

2 Press the UP or DOWN button repeatedly or turn

the MULTI JOG to adjust the LFE level.

The unit is initially set to O dB (maximum) and can be adjusted as shown below.

mEElmEJcF!mlni3mn

.......... ...m .....

:... ~...

.....;::.....

OFF + -20dB e -lOdB~ OdB

.. :::,

:m..:. ......

.... ...!....:

Fm$mmmI O,C,,A,

am&!lli

,$[~] {W] JAZZ CLAssl BQ.

2 Press the UP or DOWN button or turn the MULTl

JOG to select the “MAX;’ “STD” or “MIN” mode.

MIN ~ STD +-+ MAX

[MIN] You can enjoy the full dynamic range sound like in the movie

theater.

[STD]

Original position, when playing back in home, that is

recommended by the software producers. [MAX] Select this mode when playing back at low volume. This is the mode when playing back in the mid night.

When not using a sub-woofer While the Dolby Digital surround (except “2chSTEREO”) is activated, press the MANUAL SELECT button on the remote control once so that “SUBW ON” is displayed. Then, press the

UP button or turn the MULTI JOG within 4 seconds to display “SUBW OFF” The LFE signals are redistributed to the other speakers. To restore, press the MANUAL SELECT button once so that “SUBW OFF is displayed, then press the DOWN button or turn the MULTI JOG to display “SUBW ON:

When setting the sub-woofer mode of the Dolby Digital surround to “SUBW OFF,”that of the Dolby Pro Logic is also set to “SUBW OFF,” and vice versa. In this case, the sub-woofer signals are

redistributed to the other speakers.

ENGLISH“18

SELECTING DTS SURROUND

The optimal DTS surround modes and settings depend on the typeand placement of thespeakers. Itisrecommended thatthe optional Aiwa speakers should be used for ail channels, for example, the SX-AVR2700 speaker system. Check the current type and placement of your speakers and select the recommended mode accordingly.

The recommended mode

Center speaker No

Surround speaker (Rear sDeaker)

No surround speaker

4 ch mode: Select this mode when the center speaker is not

connected. AH center channel signals are redistributed to the

left and right channel speakers. 3 STEREO mode: Select this mode when the surround speakers are not connected.

5.lch

3 STEREO

TO SELECT A DTS SURROUND MODE

centerspeaker

4 ch

2chSTERE0

Before playing a disc, adjust the speaker level balance in Dolby Digital or Dolby Pro Logic mode as described in page 16.

To adjust the balance while listening to the source, see the

right column in page 17 and follow the steps 2 and 3. The delay time of the center and surround speakers cannot be adjusted in DTS surround mode.

● Depending on the sound source or listening condition, surround

effect may not be obtained even when the DTS surround is selected.

● The full DTS surround effect cannot be obtained when using

software not recorded in the DTS surround system. In this case, use the DSP surround system instead (see page 10).

● When headphones are plugged in, DTS surround mode is

automatically changed to “2chSTERE0.”

QWhile headphones are plugged in, DTS surround mode cannot

be changed.

To listen to the original DTS sound

When the DTS is appears on the display, all the sound settings can be canceled for DTS sound.

1 While the DTS surround is activated, press the

ENTER button on the main unit and hold it down until “BYPASS OFF” runs through on the display.

Preparation When selecting a DTS surround, select the CD function and play a disc recorded in DTS surround before selecting the mode.

1 Press the SURROUND button and turn the MULTI

JOG to select the appropriate mode.

The selected mode name appears on the display.

..... .

.... .: ... :...

....- :: .:. .... . .

~ 5.ICH —-----+4ch

Gm.1.ru

— 3 STEREO

;;.

;:”

mmmimkmi

rmmmmmmmim’a ; ; mxKlaQEI QEzimmEicEm , : ,

.... . ..... ... .... ... ... .......... :

;-t.:: :: :: ::

. . ....

““”’:: : ““””’””--”””’”:

:,mm; ;:... ;., . , : :

:m..: . . .

., . .

13mol.avl

imrtim

2 Press the UP or DOWN button or turn the MULTI

JOG to display “BYPASS ON.”

..... ... .... ... ... . :

:... .

:: ::

:... . . :... :...::...

L..’

; ; :

restore the sound settings

Repeat steps 1 and 2 so that “BYPASS OFF” appears.

:.., :::.,.:

:Omo,:,m.o:

;,:: :

;,m.~:..: .

DIGWAL

mmmrmsim

To select the 2chSTERE0 mode, press the SURROUND button repeatedly until “2chSTERE0 appears.

19 ENGLISH

OPERATING TV, CABLE TV, VCR

AND CD PLAYER

You can control basic functions of aTV, CABLE TV, VCR and CD player with this remote control.

TO ENTER THE ID CODE OF THE

EXTERNAL EQUIPMENT

Indicator

DIGIT buttons

(o-9)

MODE SELECT

SET

You can check the stored ID code by counting the indicator blinking,

1 Press either the TV, CABLE, VCR or CD button.

For example, to clheck the stored code for CD player, press

CD. 2 Press and hold the SETUP button for about 2.5 seconds. 3 Press “9: “9” and “O.” 4 Press”1 ;’ and ccmnt the indicator blinks.

For example, in the case that the stored ID is”1 57.”

The indicator blinks once,

Press “2;’ and ccwnt the indicator blinks.

The indicator blinks five times,

Press “3;’ and count the indicator blinks.

The indicator blinks seven times,

TO CONTROL TV, CABLE TV, VCR AND CD

PLAYER

~it.~~..~

‘..

~;$$$j;

Before attempting to control them, be sure to enter the ID code of the external equipment to the remote control as follows,

Confirm the code number of the external equipment.

See the ID code list in the “APPENDIX at the end of this manual.

Press either the TV, CABLE, VCR or CD button in the MODE SELECT area.

Press and hold the SET UP button for about 2.5

seconds.

Confirm that the indicator blinks twice while pressing the SET UP button,

Press three DIGIT buttons which correspond to the ID code of the external equipment.

For example, if your CD player is an AIWA unit, the required

ID code is 124 or 157. In this case, press the DIGIT buttons in

the order of”1; “2” and “4” (or “1; ‘(5” and “7” ).

After the third DIGIT button is pressed, the indicator blinks twice indicating that the ID code is correct and is stored on the remote control.

CHANNEL -

MODE SELECT

POWER

Press any button in the MODE SELECT area (TV,

VOLUME

DIGIT buttons (O-9) and ENTER

VCRICD

lI:Pause, =: Stop, t4<:Rewind, E: Play,

FM :Fast forward

CABLE, VCR or CD).

The remote conlrol is ready to operate the selected mode equipment.

Press one of the buttons indicated above.

For the use of the O – 9 and the ENTER buttons, see the instruction manual supplied with the unit to be controlled.

Other buttons indicated above have the same function which

you will find on the unit to be controlled.

● Reenter the ID CCIDE of the external equipment after replacing

the batteries of the remote control.

s If there are plural ID codes for external equipment in Ihe

“APPENDIX,” try f?ach number listed until you can control the external equipment.

Ifl

ENGLISH

ON SCREEN DISPLAY

The receiver provides an “On Screen Display” function to show the receiver settings on the TV screen. With the TV turned on, when you operate the receiver buttons or remote control buttons, the settings appear on the TV screen as well as the receiver display. The following are examples of the “On Screen Display.”

When turning on the receiver, pressing the function buttons, or tuning in a station On the right side of the screen, the setting results appear for 5 seconds.

Video V I DEO 1

Aud\o FM

TAPE OFF

_{ MUT<G

TUNER FREQ

87.50 MHz

“MUTING ON” continues flashing until MUTING mode is set to off.

VOL 10

SETTING THE CLOCK

;,.

2 1,3

DIGITAUANALOISJBAND

When the AC cord is connected for the first time, the clock on

the display flashes.

Set the time as follows while the power is off.

Press the ENTER button on the main unit.

The display becomes a little brighter.

CJCXX3

QKIC2

000

ccl

.Qo

0::=

000,

CLOCK

When pressing audio effect buttons such as SURROUND,

DSP, GEQ, T-BASS, BBE and MANUAL SELECT On the left side of the screen, the audio effect settings appear for 5 seconds.

PRO LOG IC OFF D~P OFF

LVL MAX

R LVL

GEQ OFF T-BASS

BBE

When pressing CLOCK or SLEEP buttons on the remote control

On the left side of the screen, the timer setting and the present time appear for 5 seconds.

The receiver provides an “On Screen Display” function only when the TV IS connected to the MONITOR VIDEO OUT jack.

OFF OFF

MAX

Turn the MULTI JOG to designate the hour and the minute.

The time advances by turning it to right, and decreases by turning it to left. The DOWN or UP button is also available. Press the button repeatedly. To change the time rapidly in 10-minute steps, hold it down.

Press the ENTER button on the main unit.

The clock starts from 00 seconds.

When the clock is set for the first time after purchase Everything on the display will clear. This is because the power economizing mode of the unit is activated, and is not a malfunction, The power economizing mode can be canceled. See page 7 for details.

To correct the current time Press the POWER button to turn the unit off. Carry out steps 1 to 3 above.

To display the current time Press the CLOCK button on the remote control. The clock is displayed for 4 seconds.

To switch to the 24-hour standard While the power is on, prese the CLOCK button on the remote control to display the clock. Then press the DIGITAUANALOG/ BAND button while the clock is displayed. Repeat the same procedure to restore the 12-hour standard.

21 ENGLISH

If the clock display flashes while the power is off

This is caused by a power interruption. The current time needs to be reset.

If power is interrupted for more than approximately 24 hours, all

settings stored in memory after purchase need to be reset.

SETTING THE SLEEP TIMER

2 1

UP, DOWN

The receiver can be automatically turned off at a specified time,

1 Press the AIWA RECEIVER button.

2 Press the SLEEP button.

mmBmElcimDcmE&D ~

SLEEP

Imt57x7 mm Irmm l~a I-I , , .

.. .. . ...... . . . . . . . . .. ....

:.. . ; :

... . :... :...:

:::

.... .... . ..... .... . . . .... . . . ..

:..,

, :...:

Iimmititi

The unit will be turned off after about 60 minutes.

To specify the time until the power is turned off Press the UP or DOWN button repeatedly within four seconds after step 2. Each time the button is pressed, the time changes between 5 and 240 minutes in 5-minute steps.

SLEEP

Cmm3mmcmmcxima

Cm2smmmcmammmm : , ,

. . . . . . . . . . . . . . . . . .

:,+, ;

:... :... :...:

::::

. . . . . . . . . . . . . . . . . . . .

[z=J:::

Specified time

To check the time remaining until the power is turned off Press the SLEEP button once. The remaining time is displayed for four seconds,

To cancel the sleep timer Press the SLEEP button twice so that “SLEEP on the display disappears.

ENGLISH

SPECIFICATIONS

FM tuner section

Tuning range 87.5 MHz to 108 MHz Usable sensitivity 13.2 dBf

(IHF)

Antenna terminals 75 ohms (unbalanced)

AM tuner section

Tuning range 530 kHz to 1710 kHz (1O kHz step),

531 kHz to 1602 kHz (9 kHz step)

Usable sensitivity

Antenna Loop antenna

Amplifier section

Power output [Stereo Mode]

Total harmonic 0.15 % (85 W, 1 kHz, 8 ohms, Front)

distortion

Inputs AUDIO IN

350 @J/m

Front 170 watts per channel, Min. RMS at 8 ohms, from 40 Hz to 20 kHz, with no more than 0.970 Total Harmonic Distortion

[Dolby Digital Surround or Dolby

Pro Logic Mode] Front 120 watts per channel, Min. RMS at 8 ohms, from 40 Hz to 20 kHz, with no more than 0.9% Total Harmonic Distortion Rear (Surround) 120 watts per channel, Min. RMS at 8 ohms, 1 kHz, with no more than 0,97. Total Harmonic Distortion Center 120 watts, Min. RMS at 8 ohms, 1 kHz, with no more than 0.97. Total Harmonic Distortion

PHONO: 2.5 mV, adjustable (47

kohms) CD, VIDEO l/DVD/MD, VIDEO 2/ LD/TV, VIDEO 3:300 mV, adjustable (47 kohms) TAPE MONITOR: 300 mv, adjustable (47 kohms) AUX: 230 mV, adjustable (47 kohms)

DIGITAL IN

COAXIAL (VIDEO 2): OPTICAL (VIDEO 1): OPTICAL (VIDEO 3): OPTICAL (CD): accept linear PCM (32 kHz, 44,1 kHz and 48 kHz) signals and bit stream of Dolby Digital and DTS Surround

VIDEO IN: 1 Vp-p (75 ohms)

outputs

Muting

AUDIO OUT (REC OUT): 250 mV (1

kohm)

VIDEO OUT (MONITOR): 1 VP-P (75

ohms) SUPER WOOFER: 5.0 V FRONT SPEAKERS IMP: 8f2/4Q selectable (front speakers A and B):

with the SPEAKER IMPEDANCE SELECTOR set to 4Q, accepts speakers of 4 ohms. with the SPEAKER IMPEDANCE SELECTOR set to 8Q, accepts speakers of 8 ohms or more.

SURROUND SPEAKERS IMP: 8!2

(surround speakers): accepts speakers of 8 ohms or more

CENTER SPEAKER IMP: 8Q/4Q

selectable

with the SPEAKER IMPEDANCE SELECTOR set to 4Q accepts speaker of 4 ohms. with the SPEAKER IMPEDANCE SELECTOR set to 8Q, accepts

speaker of 8 ohms or more. PHONES (stereo jack): accepts headphones of 32 ohms or more

-20 dB

General

Power requirements Power consumption Dimensions

(W XHXD)

Weight

Specifications and external appearance are subject to change without notice.

WWSYSTEM

The word “BBE” and the “BBE symbol” are trademarks of BBE Sound, Inc. Under license from BBE sound, Inc.

● Manufactured under license from Dolby Laboratories.

● Manufactured under license from Digital Theater Systems, Inc.

US Pat. No. 5,451,942 and other world-wide patents issued and pending. “DTS and “DTS Digital Surround” are trademarks of Digital Theater Systems, Inc. @l 996 Digital Theater systems, Inc. All Rights Reserved.

120 V AC, 60

230 W 430 x 155 x 385 mm

(17x6’/8 x15’/, in.)

12 kg (26 lb 7

OZ.)

23 ENGLISH

+ 56 hidden pages