Sony RMTP100, ANM1000 Users Manual

4-253-728-11(1)

Custom Integrated
AV System

Installation Manual
Owner’s Record

The model and serial numbers are located on the rear panel. Record the model
and serial numbers in the spaces provided below. Refer to them whenever you
call upon your Sony dealer regarding this product.

Model No. Serial No.

CAV -M1000ES

 2004 Sony Corporation

WARNING

To prevent fire or shock
hazard, do not expose the
unit to rain or moisture.
To avoid electrical shock,
do not open the cabinet.
Refer servicing to qualified
personnel only.

This symbol is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a
risk of electric shock to persons.

This symbol is intended to alert the
user to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.

WARNING

This equipment has been tested and found
to comply with the limits for a Class B
digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential
installation. This equipment generates,
uses, and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur
in a particular installation. If this
equipment does cause harmful interference
to radio or television reception, which can
be determined by turning the equipment
off and on, the user is encouraged to try to
correct the interference by one or more of
the following measures:
– Reorient or relocate the receiving

antenna.

– Increase the separation between the

equipment and receiver.

– Connect the equipment to an outlet on a

circuit different from that to which the
receiver is connected.

– Consult the dealer or an experienced

radio/TV technician for help.

CAUTION

You are cautioned that any changes or
modification not expressly approved in this
manual could void your authority to
operate this equipment.

If you have any questions about this
product, you may call;
Sony Customer Information Services
Center 1-800-222-7669 or
http://www.sony.com

Declaration of Conformity

Trade name: SONY
Model No.: CAV-M1000ES
Responsible Party: Sony Electronics
Inc.
Address: 680 Kinderkamack Road,

Oradell, NJ 07649 USA

Telephone No.: 201-930-6972
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.

Declaration of Conformity

Trade name: SONY

Model No.: RM-TP100

Responsible Party: Sony Electronics

Inc.

Address: 680 Kinderkamack Road,

Oradell, NJ 07649 USA

Telephone No.: 201-930-6972
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.

Important Safety Instruction

1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings.

Install in accordance with the
manufacturer’s instrucitons.

8 Do not install near any heat sources such

as radiators, heat registers, stoves, or
other apparatus (including amplifiers)
that produce heat.

9 Do not defeat the safety purpose of the

polarized or grounding-type plug. A
polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third
grounding prong. The wide blade or the
third prong are provided for your safety.
If the provided plug does not fit into
your outlet, consult an electrician for
replacement of the obsolete outlet.

10Protect the power cord from being

walked on or pinched particularly at
plugs, convenience receptacles, and the
point where they exit from the
apparatus.

11Only use attachments/accessories

specified by the manufacturer.

12 Use only with the cart,

stand, tripod, bracket, or
table specified by the
manufacturer, or sold with
the apparatus. When a cart
is used, use caution when
moving the cart/apparatus
combination to avoid injury
from tip-over.

13Unplug this apparatus during lightning

storms or when unused for long periods
of time.

14Refer all servicing to qualified service

personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus,
the apparatus has been exposed to rain
or moisture, does not operate normally,
or has been dropped.

Welcome!

Thank you for purchasing the Sony Custom
Integrated AV System. Before operating the
unit, please read this manual thoroughly
and retain it for future reference.

2

TABLE OF CONTENTS

Chapter 1 Getting Started

Features 4
Unpacking 6
Parts and Controls 7
Before Customizing the System 14

Chapter 2
Setting up the Main Unit

Installing the Main Unit 15
Hooking up the Main Unit 16
Selecting the Source and the Volume Level

of the Main Unit 18

Setting up the Remote Code and the Baud Rate

– SETUP mode 19

Learning the Remote Code for a Connected

Component

– LEARN Mode 20
Testing Learned Remote Code – CHECK Mode 22
Customizing the Main Unit – INSTALLATION

Mode 22

Chapter 5
Appendix

LEARN Mode Code List 34
Index 37
Using the RF Remote Control 39
Using the Keypad 40
Using the IR Remote Control for the Keypad 41

Chapter 3
Setting up the Keypad

Installing the Keypad 25
Hooking up in Each Zone 27
Customizing the Keypad 28
Testing the Components 29

Chapter 4
Other Information

Precautions 30
Troubleshooting 31
Error Messages 32
Specifications 33

3

Chapter 1

Features

Getting
Started

This chapter provides you with
information on the features of the
system, its accessories, and the parts
and controls of each component.

You can control up to eight audio/video sources in up to
six zones with this Custom Integrated AV System. The
system consists of:

– a Main Unit
– an RF Remote Control
– Keypads (optional)
– IR Remote Controls for Keypads (optional)

You can enjoy the audio/video source and the output
components by using a Keypad in each zone and an RF
Remote Control in the main zone. This Custom Integrated
AV System allows you to
– Distribute audio/video signals from eight independent

sources to six separate zones.

– Control volume adjustment, such as muting, bass and

treble adjustments for each of the six zones.

– Control up to eight source components by using an RF

Remote Control, a Keypad, or via RS 232C commands.

4

Main Unit

• Zones: Up to six zones receive up to eight source

audio/video signals.
– Preamp Outs: Four fixed outputs for zones 1 to 4,

and two variable outputs for zones 5 and 6.

– Amplification: All six zones have built-in stereo

audio amplifiers at 30 Watts per channel.

– Video outputs for all six zones
– Keypad connections: RJ45 connectors for all six zones

using CAT5 cables

• Sources: Up to eight audio/video sources can be

selected by all six zones.

• Remote code entry: Remote code commands can be

learned by the Main Unit.

– on your computer
– on the Main Unit

• 12 V trigger: Six zone-specific 12 V status outputs; each

300 mA max, total 1.2 A.

• RS232C port (Front): Allows you to connect the Main

Unit to your computer when you update the settings.

• RS232C ports (Rear): Allow you to connect a Sony DVD

Mega Changer and a Sony A/V Receiver to the Main
Unit.

Keypad

• LCD contrast adjustment.

• Connecting IR IN to an IR emitter enables you to use

the IR Remote Control for the additional range.

• RJ45 connectors enable you to use two Keypads in a
single zone.

RF Remote Control

• LCD panel configurable through your computer.

• Controls the audio/video sources in the main zone and

the other zones.

• Customize touch panels via an RS232C cable connected
to your computer.

Getting Started

Computer

Preset Commands

RF Remote Control

: Signal

: Command

RS232C

Preset Commands

RF Antenna

Audio/Video
Signal

Main
Keypad

Subsidiary
Keypad

IR Remote Control
for the Keypad

Audio/Video
Sources 1 – 8

Serial
RJ45

IR

Zone
Status

Zones 1 – 6

AV Receiver

Audio/Video
Signal

Audio/Video
Signal

Zones 1 – 6
Display/Signal

5

Unpacking

Getting Started

The CAV-M1000ES system includes the following
components:

• CAV-M1000ES Main Unit

• RM-TP100 RF Remote Control

• Charger cradle for the RF Remote Control

• AN-M1000 RF Antenna

• AC power cord

• Plug-in 4-terminal screw-type connector for speaker (6)

• RF Antenna cable

• Installation Manual (this manual)

Optional Accessories:
RMR-K100 Keypad

• IR Remote Control

• Keypad mounting bracket

• Screws for fixing the Keypad to the Keypad mounting

bracket (2)

• Installation Guide

6

12 3 4 5 6

q

q

q

q

q

987

Parts and Controls

Front panel of the Main Unit

RS232C

PROGRAM

CHECK LEARN SETUP

ENTER MODE BACK CANCEL

;

Getting Started

SOURCE SELECTZONE

ZONE VOLUME

ALL ZONE

MUTING

f

d

s

a

1 ?/1 (POWER) switch

Press to turn the power on or off.

2 Learning IR window

Used to input remote codes into the Main Unit.

3 Display window

Displays various information.

4 Mode indicators

Display the current mode. These indicators turn off in
the NORMAL mode.

5 ZONE +/–

Press to select the zone in the NORMAL mode.

6 SOURCE SELECT +/–

Press to select the source component in the NORMAL
mode.

7 RS232C connector

8 PROGRAM

Press to initiate a firmware update.

9 Cursor/ENTER

Press to select a menu.

0 MODE

Press repeatedly to select the mode of the Main Unit.

qa BACK

Press to return to the previous layer of the menu.

qs CANCEL

Press to cancel the present operation and return to the
NORMAL mode.

qd ZONE VOLUME +/–

Press to adjust the volume of the selected zone.

qf ALL ZONE MUTING

Press to set muting on or off in all zones.
Used to update the firmware of the Main Unit and to
upload/download setup data from a computer using
an RS232C cross cable.

7

Parts and Controls

q

q

qjqkq

Getting Started

Rear panel of the Main Unit

g

ANTENNA

IR OUT

VIDEO OUT

VIDEO IN

AUDIO OUT

AUDIO IN

L

R

SOURCE 1

KEYPAD

LR

FIXED

VIDEO OUT

PRE OUT

RL

SPEAKERS (CLASS II WIRING

ZONE 1

IR OUT

VIDEO OUT

VIDEO IN

AUDIO OUT

AUDIO IN

L

R

SOURCE 2

FIXED

PRE OUT

)

SPEAKERS (CLASS II WIRING

IR OUT

VIDEO IN
AUDIO IN

L

R

SOURCE 3

KEYPAD

LR

VIDEO OUT

RL

ZONE 2

VIDEO OUT

VIDEO IN

AUDIO OUT

AUDIO IN

)

SPEAKERS (CLASS II WIRING

IR OUT

VIDEO OUT
AUDIO OUT

L

R

SOURCE 4

KEYPAD

LR

FIXED

PRE OUT

RL

ZONE 3

h

IR OUT

VIDEO IN
AUDIO IN

SOURCE 5

VIDEO OUT

)

IR OUT

VIDEO OUT

VIDEO IN

AUDIO OUT

AUDIO IN

L

R

SOURCE 6

KEYPAD

LR

FIXED

VIDEO OUT

PRE OUT

RL

SPEAKERS (CLASS II WIRING

ZONE 4

IR OUT IR OUT

VIDEO OUT

VIDEO OUT

VIDEO IN

AUDIO OUT

AUDIO OUT

AUDIO IN

L

L

R

R

SOURCE 7

KEYPAD

LR

VARIABLE

VIDEO OUT

PRE OUT

RL

)

SPEAKERS (CLASS II WIRING

ZONE 5

IR OUT

VIDEO OUT

VIDEO IN

AUDIO OUT

AUDIO IN

L

R

SOURCE 8

VARIABLE
PRE OUT

)

SPEAKERS (CLASS II WIRING

COMMON

CONTROL

A1 II

KEYPAD

LR

VIDEO OUT

RL

ZONE 6

12V TRIGGER

123

456

SPEAKERS IMPEDANCE

)

USE 4-16

l

STR

DVP

AUX

RS232C

w; wa ws

~AC IN

qg RF ANTENNA (page 17)

Hooks up to the RF Antenna using a CAT5 cable, to
operate the RF Remote Control.

qh SOURCE connection jacks
a) IR OUT (page 16)

A 3.5 mm monaural mini phone jack for the
connection of an IR emitter to control the eight source
components individually. IR signals received from a
zone will be routed to the IR sensor of the source
component .

b) VIDEO IN (page 16)

An RCA jack for composite video input from a source
component.

c) VIDEO OUT (page 17)

An RCA jack for connecting a video source to another
local component.

Note

This is a buffered video connection, and this loop-through is
active even when the Main Unit is turned off, as long as the
AC power cord is plugged in.

d) AUDIO IN (page 16)

RCA jacks for stereo line level audio input from a
source component.

e) AUDIO OUT (page 17)

RCA jacks for connecting an audio source to another
local component.

Note

This is a buffered audio connection, and this loop-through is
active even when the Main Unit is turned off, as long as the
AC power cord is plugged in.

qj IR OUT COMMON (page 17)

A 3.5 mm monaural mini phone jack for the
connection of an IR emitter to control any IR­controlled component such as a lighting system or
motorized screen.

qk CONTROL A1 II (page 16)

Hooks up to a Sony source component equipped with
a matching jack allowing the Main Unit to control the
source component.

ql 12 V TRIGGER (page 17)

Provide control outputs of +12 V DC that turn devices
on and off in sync with the zone to drive voltage
sensing relay modules and AC strips.

8

w; ZONE connection jacks
a) KEYPAD (page 17)

An RJ-45 jack for the Keypad interface. Each connector
interfaces with the following: power, GND, and data
input/output.

b) VIDEO OUT (page 17)

An RCA jack that sends a source video signal selected
by the zone to the composite video input on a zone
display.

c) FIXED PRE OUT (zones 1 to 4)

An RCA jack for connecting zone audio output to an
external amplifier. For use with applications where
either more power is required for a zone, or for
passing signals to a Dolby Prologic-compatible
receiver for theater quality audio in one or more
zones.

d) VARIABLE PRE OUT (zones 5 and 6)

An RCA jack for connecting zone audio output to an
external power amplifier. The volume is attenuated via
VOLUME +/– on the Keypad.

RF Remote Control

e) SPEAKERS (page 17)

A Plug-in 4-terminal screw-type jack which accepts

speaker cords sizes up to 12AWG.

Leave the AC power cord unplugged when you hook

up speaker cords.

wa RS232C (page 16)

Hook up to other RS232C components, allowing the

Main Unit to be controlled by other RS232C

components, or to control other components that

communicate via RS232C, such as a Sony DVD Mega

Changer or a Sony A/V Receiver. Use an RS232C cross

cable for the connection.

ws AC IN (page 17)

Hooks up the supplied AC power cord to AC IN.

Getting Started

6

1 MUTING

Press to mute the audio.

2 VOLUME +/–

Press to adjust the volume.

3 SYSTEM OFF switch

Press to shut down the system.

1

MUTING

VOLUME

SYSTEM

CHANNEL

4 Cursor/ENTER

Press to control the source.

5 CHANNEL +/–

Press to control the source.

6 RS232C connector

Hook up a computer using an RS232C cable.

3

4

52

9

Parts and Controls

Getting Started

Front panel of the Keypad

1

2

3
4
5
6
7
8
9
q;

POWER

PAGE SOURCE MUTING

VOLUME

qa

2

qs

qd

qf

qg

1 IR sensor

Receives IR signals from the IR Remote Control for the
Keypad (supplied) to control both source components
and the system.

2 SELECT

Press to select a menu on the LCD display, such as a
source menu, a disc title list, etc.

3 PAGE

Press to return to the previous menu or to view the
current status of the disc title list and the preset station
list. If there is no list, only a source name will be
displayed.

4

5 X (PAUSE)

6 > (AMS)

7 .(AMS)

(LOCK)

Press to lock the selected source component in.

Press to pause the playback.

Press to advance the track or to select a preset station.

Press to go reverse the track or to select a preset
station.

8 POWER switch

Press to turn the power of the Keypad on or off.

9 N (PLAY)

Press to operate the selected source.

0 x (STOP)

Press to stop playback.

qa Display window

Displays the selected source, the zone volume level,
the zone and the system status, and other system
status information.

qs SCROLL UP/DOWN

Press to scroll the LCD menu.

qd MUTING

Press to mute the speaker output in the zone.

qf SOURCE

Press to return to the source components list screen.

qg VOLUME +/–

Press to adjust the volume in a zone.

10

Rear panel of the Keypad

Getting Started

qk

ql

qh TO SPEAKERS (page 27)

Connects speaker cords to the speakers in a zone.

qj CAT5 OUT (page 27)

Connects a CAT5 cable to the CAT5 IN jack of the
subsidiary Keypad when used in a single room

OUT

IR IN

TO SPEAKERS

R

L

SUB

FROM AMPLIFIER

R

MODE

MAIN

L

w;qh

IN

waqj

qk IR IN (page 27)

Connects an optional IR cord so you can operate the IR
Remote Control for the Keypad by pointing it at the IR
sensor of the IR emitter.

ql MODE switch (page 27)

When using two Keypads in a single room, set this
switch to SUB on the subsidiary Keypad.

w; FROM AMPLIFIER (page 27)

Connect speaker cords to the Main Unit.

wa CAT5 IN (page 27)

Connects a CAT5 cable from the Main Unit to the main
Keypad.

11

Parts and Controls

Getting Started

IR Remote Control for Keypads

Buttons marked in grey are used to control the source
components.

1 SLEEP

Press to activate the sleep function that turns off the
Keypad automatically after the specified duration.
The time changes as shown below

2:00 t1:30 t1:00 t0:30 tOFF

2 DIMMER

Press repeatedly to change the brighteness of the LCD
backlight.

3 Numeral

Press to select a number, representing, for example, a
desired track of the source.

4 SELECT

Press to select a menu on the display on the LCD, such
as a source menu, a disc title list, etc.

5 LOCK

Press to lock the selected source component in.

6 PAGE

Press to return to the previous menu or to view the
current status of the disc title list or the preset station
list. If there is no list, only a source name will be
displayed.

7 DOWN

Press to scroll the LCD menu down.

8 ./> (AMS)

Press to locate a specific track of the source or to select
a preset station.

9 X (PAUSE)

Press to pause the playback of the source.

0 N (PLAY)

Press to operate the selected source.

qa TOP MENU/GUIDE

Press to display the top menu while using a source
component such as a DVD player.

qs CURSOR/ENTER

Press to select a menu while using a source component
such as a DVD player.

qd DISPLAY

Press to display on-screen messages from equipment
such as a DVD player.

qf RETURN/EXIT

Press to return to the previous menu screen (level) or
to quit the menu function while using a source
component such as a DVD player.

qg TV VOL +/–

Press to adjust the TV volume.

qh TV CH +/–

Press to change the TV channel.

qj ?/1 switch

Press to turn the Keypad on/off.

qk TV ?/1 switch

Press to turn the TV on/off.

ql ENTER

Press to confirm the selection.

w; DISC

Press to select a disc of a DVD/CD Mega Changer.

wa SOURCE

Press to return to the source components list screen.

ws UP

Press to scroll the LCD menu up.

wd m/M

Press to locate a portion you want to play within a
track of the source.

wf x (STOP)

Press to stop the current playback.

wg MENU

Press to display a menu while using a source
component such as a DVD player.

wh MUTING

Press to mute the speaker output in a zone.

wj VOLUME +/–

Press to adjust the volume in a zone.

wk F1

A button reserved for source components.

wl F2

A button reserved for source components.

e; FOLDER

Press to move to the FOLDER screen while using a
DVD player.

ea TV/VIDEO

Press to switch signals between TV input and Video
input.

12

Getting Started

1

2

3

4
5
6wa

SLEEP DIMMER

1234

5678

90

TV

>10

SELECT

LOCK DISC

PAGE SOURCE

UP

DOWN

ENTER

qj

qk

ql

w;

7ws
8wd
9
q;

qa

qs

TOP MENU/

GUIDE

MENU MUTING

VOLUME

wf
wg
wh
wj

qd
qf
qg

TV VOL TV CH FOLDER F1

RETURN/EXITDISPLAY

TV/VIDEO F2

wk
wl

qh

e;
ea

13

Before Customizing the System

Getting Started

Be sure to read the following procedure thoroughly before
you actually make any settings.

Overview

The following chart gives an overview of how to set up
the Main Unit system.

Setting up the Main Unit

- Install the Main Unit. (page 15)

- Connect components, such as source components and
outut components, to the Main Unit. (page 16)

- Make other connections.

Setting up a Keypad

- Install the Keypad into a junction box. (page 25)

- Connect the Main Unit and the Keypad. (pae 17)

Customizing the Main Unit

- Customize the Main Unit on your computer. (page 19)

- Customize the Main Unit. (page 20)

Testing the components (page 29)

Planning the system

Before setting up the system, plan the system
configuration.

1 Decide the source components to be connected to

each SOURCE connection of the Main Unit.

2 Decide the allocation of the components to be

used in each zone.

Setting up the RF Remote Control

- Customize the RF Remote Control on your computer.

For detailed information on the RF Remote Control, please
consult your nearest Sony dealer.

14

Chapter 2

Installing the Main Unit

Setting up the
Main Unit

This chapter provides you with
information on the Main Unit
regarding installation, hookups and
settings.

When you mount the Main Unit, note the following:

•Place the Main Unit in a location with adequate
ventilation to prevent heat buildup and prolong the life
of the receiver.

• Do not place the Main Unit near heat sources, or in a
place subject to direct sunlight, excessive dust or
mechanical shock.

• Do not place anything on top of the cabinet that might
block the ventilation holes and cause malfunctions.

• Do not cover the rear panel.

• Use caution when placing the unit or speakers on

surfaces that have been specially treated (with wax, oil,
polish, etc.) as staining or discoloration of the surface
may result.

Installing the RF Antenna

Mount the RF Antenna in an appropriate place in the
room where the RF Remote Control is to be used.
For details on how to make the connection, refer to “RF
Antenna hookup” on page 17.

Horizontal position

Setting up the Main Unit

Vertical position

15

Hooking up the Main Unit

AMBEGF D LH

Before hooking up the Main Unit, be sure the power cord
is unplugged. Refer to the figures below for the
connections.

Source component hookups

Setting up the Main Unit

AUDIO IN jack (A)

Hook up the audio output of each source component and
the AUDIO IN jack of each SOURCE connection jack of
the Main Unit.
Use RCA audio cables.

VIDEO IN jack (B)

Hook up the video output of each source component and
the VIDEO IN jack of each SOURCE connection jack of the
Main Unit.
Use an RCA video cable.

RS232C connector (C)

Hook up any RS232C equipped source component and
the RS232C connector of the Main Unit.
Use a DB9 cross cable.
You can control the connected RS232C components from
the Main Unit by sending commands.

CONTROL A1II jack (D)

Hook up each CONTROL A1II jack of the source
equipment such as XXXX and the Main Unit.
Use a CONTROL A1II cable.
You can control the connected source component from the
Main Unit.

IR OUT jack (E)

Plug the IR emitter into the IR OUT jack of each SOURCE
connection jack of the Main Unit. Be careful to match the
source audio and video connection number on the Main
Unit to the IR emitter connector number.
The IR control signal will be routed to the correct source
component. Find the IR sensor window on the source
component and attach the emitter to the component
sensor.

IR OUT

IR OUT

IR OUT

IR OUT

VIDEO OUT

VIDEO IN

AUDIO OUT

AUDIO IN

L

R

SOURCE 4

KEYPAD

LR

FIXED

PRE OUT

RL

ZONE 3

IR OUT

VIDEO IN
AUDIO IN

SOURCE 5

VIDEO OUT

VIDEO OUT
AUDIO OUT

L

R

FIXED

PRE OUT

RL

)

SPEAKERS (CLASS II WIRING

ZONE 4

KEYPAD

ANTENNA

VIDEO OUT

VIDEO OUT

VIDEO IN

VIDEO IN

AUDIO OUT

AUDIO IN

AUDIO IN

L

R

SOURCE 1

SOURCE 2

KEYPAD

LR

FIXED

VIDEO OUT

PRE OUT

RL

ZONE 1

)

J

SPEAKERS (CLASS II WIRING

SPEAKERS (CLASS II WIRING

KI C N

AUDIO OUT

L

R

FIXED

PRE OUT

RL

ZONE 2

VIDEO IN
AUDIO IN

SOURCE 3

KEYPAD

LR

VIDEO OUT
AUDIO OUT

L

R

VIDEO OUT

)

SPEAKERS (CLASS II WIRING

16

IR OUT

VIDEO IN
AUDIO IN

SOURCE 6

LR

VIDEO OUT

VIDEO OUT
AUDIO OUT

L

R

)

SPEAKERS (CLASS II WIRING

VIDEO IN
AUDIO IN

IR OUT IR OUT

IR OUT

COMMON

VIDEO OUT

VIDEO OUT

VIDEO IN

AUDIO OUT

AUDIO OUT

AUDIO IN

L

L

CONTROL

R

KEYPAD

LR

SOURCE 8

VIDEO OUT

)

R

KEYPAD

LR

VARIABLE
PRE OUT

RL

SPEAKERS (CLASS II WIRING

ZONE 6

SOURCE 7

VARIABLE
PRE OUT

RL

ZONE 5

A1 II

VIDEO OUT

12V TRIGGER

123

456

SPEAKERS IMPEDANCE

)

USE 4-16

STR

DVP

AUX

RS232C

~AC IN

Output component hookups

AUDIO OUT jack (F)

Hook up the AUDIO OUT jack of each SOURCE
connection jack of the Main Unit and each audio input of
the external A/V receiver.
Use RCA audio cables.

VIDEO OUT jack (G)

Hook up the VIDEO OUT jack of each SOURCE
connection jack of the Main Unit and each video input of
the external A/V receiver.
Use RCA video cables.

IR OUT COMMON jack (H)

Plug the IR emitter into the IR OUT COMMON jack of the
Main Unit.
The IR control signal will be routed to the output
component (an auxiliary device that are not source
specific). Find the IR sensor window on the output
component and attach the emitter to the component
sensor.

RF Antenna hookup (M)

Hook up the RF ANTENNA jack of the Main Unit and the
jack of the RF Antenna.
Use a CAT5 cable.

AC power cord hookup (N)

Connect the supplied AC power cord to the AC IN jack.

Setting up the Main Unit

Zone related cables hookups

SPEAKERS jack (I)

Hook up the SPEAKERS jack of each ZONE connection
jack of the Main Unit and the FROM AMPLIFIER jack of
each Keypad.
Use speaker cords terminated with plug-in 4-terminal
screw-type connectors.
Leave the AC power cord unplugged when you hook up
speaker cords.

VIDEO OUT jack (J)

Hook up the VIDEO OUT jack of each ZONE connection
jack of the Main Unit and the video input of the TV
monitor in each zone.
Use an RCA video cable.

KEYPAD jack (K)

Hook up the KEYPAD jack of each ZONE connection jack
of the Main Unit and the CAT5 IN jack of each Keypad.
Use a CAT5 cable.

12 V TRIGGER jack (L)

Hook up the 12 V TRIGGER jack of the Main Unit and
the device used to drive a voltage sensing relay module
and an AC strip.
Use a 3.5 mm mini phone cable.

17

Selecting the Source and the Volume Level
of the Main Unit

Selecting the source for each zone

In the NORMAL mode, you can select a source
component for each zone. The status information for each
zone appears on the display window.

Setting up the Main Unit

1 Select a zone by pressing the ZONE + or ZONE –

button.

2 Select a source component by pressing the SOURCE

+ or SOURCE – button.

The source component is confirmed one second after
you release the SOURCE button.

Example 1:

Example 2: When you connect a source component

When a source component connected to the

SOURCE 1 Out/In plugs is selected in ZONE 1.

ZONE1 : SOURCE 1

ZONE SOURCE Title SOURCE No

whose title has changed from SOURCE 1 to
DVD in the PC SETUP mode.

r

Adjusting the volume in each zone

1 Press ZONE+ or ZONE – repeatedly to select a zone.
2 Press ZONE VOLUME+ or VOLUME – to display the

current volume level.

The display window changes as shown below.

t VOLUME MIN

VOLUME 1

…

VOLUME 73

t VOLUME MAX

Note

The volume level displayed in the display window varies
depending on the volume limits you have set as described in

X

“Setting volume limits” on page 28.

3 Press ZONE VOLUME+ or VOLUME – repeatedly to

adjust the volume to the desired level.

The display window returns to the NORMAL mode in
a few seconds after you have finished.

Note

In a zone where SOURCE INPUT OFFSET is ON, the actual
volume level is lower than the displayed volume level.

Tip

Even when you connect several DVD players to the Main
Unit, you can distinguish each of them by the source number
displayed on the far right side in the display window.

Turning ALL ZONE MUTING on or off

1 Press ALL ZONE MUTING on the Main Unit.

“ALL ZONE MUTING” appears in the display
window.

2 To turn ALL ZONE MUTING off, press ALL ZONE

MUTING again.

“MUTING OFF” appears for a few seconds, then the
display window returns to the previous display.

18

Setting up the Remote Code and the Baud Rate
– SETUP mode

Setting the baud rate – BAUD RATE SET

You can adjust the baud rate between the Main Unit and
an FM/AM Receiver (STR) or DVD Mega Changer
connected via an RS232C connection.

1 Press MODE repeatedly until ”<<SETUP>>” appears

in the display window, then press ENTER.

2 Press the R cursor or r cursor to select ”BAUD RATE

SET”.

3 Press ENTER.

”WHICH PORT?” appears for a few seconds.

4 Press the R cursor or r cursor to select a port.

Each time you press the R cursor or r cursor, the
display window changes cyclically as shown below.

WHICH PORT? (Appears for a few seconds)

Y

t FRONT RS232C

STR RS232C
DVP RS232C

t AUX RS232C

R r
R r
R r
R r

5 Press ENTER.

The baud rate setting display appears.

6 Press the R cursor or r cursor to select the desired

baud rate.

Each time you press the R cursor or r cursor, the
display window changes cyclically as shown below.

t 9600 bps

14400 bps
19200 bps
38400 bps
57600 bps
115200 bps

t 128000 bps

R r
R r
R r
R r
R r
R r
R r

7 Press ENTER when you have finished.

The display window returns to the NORMAL mode.

Setting up the Main Unit connected to a
computer – PC SETUP

You can transfer setting data to the Main Unit and
customize it using an RS232C connection to your
computer.
The items that should be customized on your computer
are the following.

• The information needed to specify the source component,
output component, and remote code settings

• 12V Trigger

Note

Do not connect speakers and a TV to the Main Unit while in
the PC SETUP mode.

1 Connect the RS232C connector on the Main Unit to

your computer with an RS232C cross cable.

2 Press MODE repeatedly until ”<<SETUP>>” appears

in the display window, then press ENTER.

“WHICH MENU?” appears for a few seconds.

3 Select “PC SETUP” by pressing the R cursor or r

cursor.

Each time you press the R cursor or r cursor, the
display window changes as follows:

“PC SETUP R r” y “BAUD RATE SET R r”

4 Press ENTER.

“READY!” appears in the display window. You are
now ready to transfer data between the Main Unit and
your computer.

5 <TBD> (STEP TAKEN ON THE PC)
6 “PLEASE WAIT…” appears while data is being

transferred.

When the data has been transferred successfully,
“COMPLETED!” appears in the display window.
If the data transfer is unsuccessful, “FAILED!” appears
in the display window.

7 Press ENTER when you have finished.

Setting up the Main Unit

19

Learning the Remote Code for a Connected Component
– LEARN Mode

You can enter any remote codes, even if the remote code
that you want to enter is not preset in the SETUP mode.

Learning the remote code - CODE

Setting up the Main Unit

LEARNING

1 Press MODE repeatedly until “<<LEARN>>” appears

in the display window, then press ENTER.

“WHICH MENU?” appears for a few seconds.

2 Press the cursor R or rrepeatedly to select “CODE

LEARNING”, then press ENTER.

“CONNECT TO?” appears for a few seconds.

3 Press the cursor R or r repeatedly to select the

desired component.

Each time you press the cursor R or r , the display
window changes cyclically as shown below.

CONNECT TO? (Appears for a few seconds)

r

t SOURCE 1

……

SOURCE 8
COMMON 1

t COMMON 10

Notes

• The SOURCE or COMMON, which has already been
learned by the Main Unit in the PC SETUP mode, appears
with an exclamation mark ( ! ) at the left side of the display
window.

• Components that have not been connected to the Main Unit
are grayed out in the display window. You cannot select
them.

4 Press ENTER.

“INPUT IR CODE” appears for a few seconds, then
display window changes to “CODE ID #001 R r”.

R r

R r

R r

R r

5

While the code ID number is displayed in the
display window, press the corresponding button
on the remote control of the component while
pointing it toward the learning IR window of the
Main Unit.

When your entries are confirmed, “COMPLETED!”
appears for a few seconds, then the display window
moves to the next remote code entry.
If your entries are not confirmed, “LEARN FAILED!”
appears for a few seconds, then the failed code ID
number appears.

Tips

• When you want to skip the code ID number, press the
cursor r.

• When you want to re-enter the code ID, press the cursor R.

Notes

• When the remote code has been successfully learned, a “*”
will appear next to the remote code name.

• You can enter up to 50 remote codes into the Main Unit.

• You must complete step 5 within one minute after the

remote code name is displayed in the display window;
otherwise, your entry will not be learned and “LEARN
FAILED!” appears.

6

Repeat step 5 to enter other remote codes.

7

Press ENTER when you have finished.

“SETTING NOW…” appears for a few seconds. Then,
the display window returns to the NORMAL mode.

Notes

• Even if you quit the LEARN mode in the midst of making
the settings, the remote codes that have already been
learned will be stored.

• Some remote codes cannot be learned. In this case,
“MEMORY FULL” appears, then the display window

returns to the previous remote code entry. The remote
codes that have already been learned will be stored.

• The remote codes that have already been learned in the PC
SETUP mode are grayed out in the display window.

Note

Refer to “LEARN Mode Codes List” on page 34 to see the
code ID number corresponding to each IR command. For
example, “CODE ID #001” indicates “Power”.

20

You can add new remote codes using EXPAND CODE.

Adding a new remote key - EXPAND CODE

1 Press MODE repeatedly until “<<LEARN>>” appears

in the display window, then press ENTER.

“WHICH MENU?” appears for a few seconds.

2 Press the R cursor or r cursor to select “EXPAND

CODE”, then press ENTER.

“CONNECT TO?” appears for a few seconds.

3 Press the R cursor or r cursor repeatedly to select

the desired component.

Each time you press the R cursor or r cursor, the
display window changes cyclically as shown below.

CONNECT TO? (Appears for a few seconds)

r

t SOURCE 1

R r

• You can add up to 10 additional remote codes to the Main
Unit.

• You must complete step 5 within one minute after the
remote code name is displayed in the display window;
otherwise, your entry will not be learned and “LEARN
FAILED!” appears.

Setting up the Main Unit

6 Repeat step 5 to enter other remote codes.
7 Press ENTER when you have finished.

“SETTING NOW…” appears for a few seconds.
The display window returns to the NORMAL mode.

Notes

• Even if you quit the LEARN mode in the midst of making
the settings, the remote codes that have already been
learned will be stored.

• Some remote codes cannot be learned. In this case,
“MEMORY FULL” appears, then the display window

returns to the previous remote code entry. The remote
codes that have previously been learned will be stored. You
cannot select them.

SOURCE 8
COMMON 1

R r

R r

……

t COMMON 10

Note

Remote codes that have not already been learned by the Main
Unit are grayed out in the display window. You cannot select
them.

R r

4 Press ENTER.

“INPUT IR CODE” appears for a few seconds, then
the display window changes to “CODE ID #100”.

5 While the code ID number is displayed in the

display window, press the corresponding button
on the remote control of the component while
pointing it toward the learning IR window of the
Main Unit.

When your entries are confirmed, “COMPLETED!”
appears for a few seconds, then the display window
moves to the next remote code entry.
If your entries are not confirmed, “LEARN FAILED!”
appears for a few seconds, then the failed code ID
number appears.

Tips

• When you want to skip the code ID number, press the r
cursor.

• When you want to re-enter the code ID, press the R cursor.

Notes

• When the remote code is successfully learned, a “*” will
appear next to the remote code name.

21

Testing Learned Remote

Customizing the Main Unit

Code – CHECK Mode

You can check to see if the remote code of the source
component have been successfully learned by the Main
Unit.

1 Press SOURCE – or SOURCE + to select the source

component that you want to check.

Setting up the Main Unit

2 Press MODE repeatedly until “<<CHECK>>“ appears

in the display window, then press ENTER.

“SET COMMAND” appears for a few seconds, then
the learned remote code appears.

3 Press the cursor R or r repeatedly to select the

remote code that you want to check.

4 Press ENTER.

The selected remote command will be performed.

– INSTALLATION Mode

Viewing disc information
– DISC SEARCH

By connecting a Sony DVD Mega Changer to an RS232C
jack, or a Sony CD Mega Changer to CONTROL A1II, you
can view disc information, such as a disc title.

1 Turn off the power.
2 Press and hold MODE and the T cursor

simultaneously, and then turn on the power.

“DISC SEARCH” appears in the display window for a
few seconds, then, “DVD MEGA” appears.

3 Press the R cursor or r cursor to select “DVD MEGA”

or “CD MEGA”.

4 Press ENTER.

“SEARCHING NOW…” appears and flashes while the
Main Unit is searching for the disc information.
“COMPLETED!” appears after the information has
been received.
“FAILED!” appears when informations is not found or
cannot be read.

5 Press ENTER when you have finished.

The display returns to the NORMAL mode.

22

Adjusting the source input offset
– SOURCE INPUT OFFSET

You can specify the maximum volume level to optimize
the acoustic conditions in each zone.

1 Turn off the power.
2 Press and hold ZONE + and ALL ZONE MUTING

simultaneously, and then turn on the power.

“SOURCE OFFSET” appears in the display window
for a few seconds.

3 Press the R cursor or r cursor repeatedly to select a

source number.

Each time you press the R cursor or r cursor, the
display window changes cyclically as shown below.

SOURCE OFFSET (Appears for a few seconds)

r

t SOURCE 1 R r

Y

SOURCE 2 R r

…

t SOURCE 8 R r

4 Press ENTER.

The display window displays the OFFSET settings.

5 Press the R cursor or r cursor to adjust the offset.

Each time you press the R cursor or r cursor, the
display window changes cyclically as shown below.

t OFFSET 0dB

OFFSET -1dB R r
OFFSET -2dB R r
OFFSET -3dB R r
OFFSET -4dB R r

t OFFSET -5dB R r

R r

Locking the settings – SETUP LOCK

You can lock in the settings under which have been
entered into the Main Unit.

1 Turn off the power.
2 Press and hold SOURCE SELECT + and BACK

simultaneously, and then turn on the power.

“SETUP LOCK” appears for a few seconds, then the
display window displays the SETUP LOCK window.

3 Press the R cursor or r cursor to turn SETUP LOCK

on or off.

The display window changes as follows:

SETUP LOCK (Appears for a few seconds)

r

LOCK [OFF]
LOCK [ON] R r

R r

4 Press ENTER when you have finished.

The display window returns to the NORMAL mode.

Notes

• The following are the preferences that can be locked in in
the SETUP LOCK mode.

- All settings in the LEARN mode.

- All settings in the SETUP mode.

- Settings for the Disc Search.

- The adjustment of SOURCE OFFSET.

- All Clear.

• When you select settings that cannot be changed,
“LOCKED!” appears for a few seconds, then the display

window returns to the NORMAL mode.

Setting up the Main Unit

6 Press ENTER when you want to adjust the offset

for other source components.

The step goes back to step 3.

7 Press CANCEL when you have finished.

The display window returns to the NORMAL mode.

Note

In a zone where SOURCE INPUT OFFSET is ON, the actual
volume level is lower than the displayed volume level.

23

Customizing the Main Unit – INSTALLATION Mode

Viewing the version information
– CIS VERSION

CIS VERSION provides you the version information of
the Main Unit and other external components, such as an
FM/AM Receiver (STR), a DVD Mega Changer, an RF
Remote Control, or the Keypad.

Setting up the Main Unit

1 Turn off the power.
1 Press and hold ZONE – and CANCEL simultaneously,

and then turn on the power.

“CIS VERSION” appears in the display window for a
few seconds.

2 Press the cursor R or r to view the version

information.

Each time you press the button, the display window
changes as shown below.

CIS VERSION (Appears for a few seconds)

r

VERSION [X.XX]: displays the version information

Y

STR [X.XX]: displays the version information

Y

DVD SYS. [X.XX]: displays the version information

Y

DVD IF. [X.XX]: displays the version information

(interface control).

Y

RF RM [X.XX]: displays the version information

Y

KEYPAD [X.XX]: displays the version information

r

NORMAL mode

of the Main Unit.

of the FM/AM RECEIVER (STR).

of the DVD MEGA CHANGER
(system control).

of the DVD MEGA CHANGER

of the RF Remote Control.

of the Keypad.

Initializing all the settings – ALL CLEAR

Note that all memory data will be deleted when you
initiate an ALL CLEAR setting.

1 Turn off the power.
2 Press and hold SOURCE SELECT + and CANCEL

simultaneously, and then turn on the power.

“MEMORY CLEARING” appears in the display
window during the initialization.
When the initialization is completed, “MEMORY
CLEARED!” appears for four seconds, then the
display window returns to the NORMAL mode.

3 Power will be turned off automatically after the

display window returns to the NORMAL mode.

Notes

• Any command keys other than POWER are not enabled during
the initialization of the Main Unit. If pressed, they are not
recognized.

• If you turn off the power before the initialization is completed,
the Main Unit will start initializing settings again when you
turn on the power the next time.

24

Chapter 3

Installing the Keypad

Setting up the
Keypad

This chapter provides you with
information regarding installation,
hookup and settings for the optional
Keypad.

A Keypad must be installed in a junction box (optional).
Follow the procedures below to mount a Keypad
mounting bracket and a Keypad on the wall.

Installing the Keypad

1 Place the Keypad mounting bracket over a junction

box which has already been installed on the wall
with the mounting lips facing out.

2 Attach the Keypad mounting bracket to the

junction box with the supplied screws at the four
points as shown below.

Proceed to the steps in “Zone related cables hookups”
on page 17 before mounting the Keypad.

Note

The Keypad mounting bracket may not fit easily over some
junction boxes. In this case, loosen the screws and move the
Keypad mounting bracket left to right to center on the
junction box.

Setting up the Keypad

25

Installing the Keypad

3 Insert the top of the Keypad onto the mounting

bracket first, in the direction of the arrow 1 until
it clicks, then push the bottom of the Keypad onto
the bracket in the direction of the arrow 2.

Setting up the Keypad

Removing the Keypad

1 Remove the screws that hold the Keypad and the

Keypad mounting bracket.

2 Press and hold the edge of the upper-side of the

Keypad tightly. Pull the lower part of the Keypad
away from the Keypad mounting bracket first,
then pull the upper part of the Keypad out
slightly, lifting it in the direction of the arrow, as
shown below.

4 Fix and tighten the Keypad mounting screws as

shown below.

Note

You may need some extra effort to remove the Keypad from
the wall since there are various kinds of junction boxes, and
the installation environment of the Keypad differs.

5 When you have finished mounting the Keypad,

check that it operates properly.

26

Hooking up in Each Zone

You must install at least one Keypad and a pair of
speakers in each zone. In the zones where both audio and
video will be installed, you must install at least one TV
monitor.
Requirements for these hookups are as follows.

• A CAT5 cable has been installed for each zone's Keypad.

• Two pairs of 12 to 18 AWG speaker cords for each pair of

speakers.

• An RCA video cable for a TV monitor from each zone to
the Main Unit location.

TV monitor hookup

Hook up the video input of the TV monitor in each zone
and the VIDEO OUT of each ZONE connection jack of the
Main Unit.
Use an RCA video cable.

Speakers hookup

1 Hook up the speaker cords from the SPEAKERS jack

of each ZONE connection jack of the Main Unit to
the FROM AMPLIFIER jack of the Keypad in each
zone.

CAT5 cable hookup

1 Set the MODE switch to MAIN on the rear panel of

the Keypad.

2 Hook up the CAT5 cable from the KEYPAD jack of

each ZONE connection jack of the Main Unit to the
IN jack of the Keypad in each zone.

To install two Keypads in the same zone

You can install two Keypads in a single room.

1 Set the MODE switch to SUB on the rear panel of

the subsidiary Keypad.

2 Hook up the CAT5 cable from the OUT jack of the

Keypad for which the MODE switch is set to MAIN,
to the IN jack of the subsidiary Keypad.

Note

Note that the length of CAT5 cables for each connection is
limited. See the figure below for the maximun length of CAT5
cables.

Main Unit Keypad

275 feet max.

Setting up the Keypad

2 Hook up the speaker cords from the TO SPEAKERS

jack of the Keypad to the speaker terminals in each
zone.

Notes

• Use speakers which have a combined impedance of
between 4 and 16 Ohms loaded.

• Twist the stripped ends of the speaker cords about
2/3 inch (10 mm). Be sure to match the speaker cord
to the appropriate terminal on the components: + to
+ and – to –. If the cords are reversed, the sound will
be distorted and will lack bass.

• 14 AWG speaker cords are recommended for
speaker runs up to 150 feet (45 m). The 4-terminal
connectors accept speaker cords sizes up to 12 AWG,
maximum.

• If you use speakers with a low maximum input
rating, adjust the volume carefully to avoid
excessive output on the speakers.

Main Unit Keypad Keypad

150 feet max. 50 feet max.

IR emitter hookup

When you want to use the IR Remote Control for the
Keypad without pointing at the IR sensor of the Keypad,
plug an IR emitter (optional) into the IR IN jack of the
Keypad.
You can operate the IR Remote Control for the Keypad
pointing at the IR sensor of the IR emitter.

27

Customizing the Keypad

Setting bass and treble

You can adjust bass and treble to optimize the acoustic
conditions in each zone.

1 Turn off the power.
2 Press and hold MUTING and LOCK simultaneously,

and then press POWER.

The LCD panel changes to the Bass and Treble setup
mode.

3 Press the corresponding SELECTION button to

adjust the bass and the treble.

4 Turn off the power when you have finished.

The settings are confirmed when the power is turned
off.

Setting up the Keypad

Notes

• All buttons, other than VOLUME +, VOLUME –, MUTING
and POWER, are disabled while you are making settings.

• You can adjust Bass and Treble between ± 14 dB and 2 dB.

Adjusting LCD contrast

1 Turn off the power.
2 Press and hold PLAY and the SELECT button in the

left-upper simultaneously, and then press POWER.

The display window enters the contrast setting mode.

3 Press the corresponding SELECTION buttons to

adjust the LCD Contrast Value.

4 Turn off the power when you have finished.

The settings are confirmed when the power is turned
off.

Notes

• All buttons other than POWER are disabled while settings
are being made.

• You can adjust the LCD contrast between level 01 and level

32.

Setting volume limits

You can customize the volume limits to protect speakers
from being over driven.

1 Turn off the power.
2 Press SOURCE and PAGE simultaneously, and then

press POWER.

The LCD touch panel changes to the Volume
limitation mode.

3 Press the corresponding SELECTION button to

adjust the maximum volume.

4 Turn off the power when you have finished.

The settings are confirmed when the power is turned
off.

Notes

• All buttons, other than VOLUME +, VOLUME –, MUTING,
and POWER, are disabled while you are making settings.

• You can adjust the volume limits between level 64 and level

74.

28

Testing the Components

y

It is recommended that you test all the components before
you finish with the installation of the entire system in
each zone so as not to encounter any problems after the
installation is completed. Check to see if the Main Unit,
the installed components, and the Keypad operate
properly by testing each operation.

1 Check the following connections.

- All the Keypads are connected to the Main Unit via CAT5
cables.

- An audio or a video component is connected between
AUDIO IN Left/Right and VIDEO IN of each SOURCE
connection jack.

- A display (output component) is connected to VIDEO OUT
at each ZONE connection jack.

- Speakers are connected to SPEAKERS at each ZONE
connection jack.

- An IR emitter is connected to IR OUT of each SOURCE
connection jack, and is placed near the IR sensor of the
source component.

- AC power cords for the Main Unit and the other
components are plugged in.

2 Turn on the Main Unit.
3 Select ZONE 1 by pressing the ZONE button on the

front panel of the Main Unit.

4 Select SOURCE 1 by pressing the SELECT SOURCE

button on the front panel of the Main Unit.

5 Turn on the Keypad in zone 1.
6 Select SOURCE 1 by pressing the SELECT button on

the Keypad. Then, check the following.

- Power control
Press POWER to turn the Keypad on or off.

- Volume adjustment
Press VOLUME +/– to adjust the volume.

- Muting
Press MUTING to mute the speaker output.

- Playback operation
Press the Play, Stop, Pause, and AMS (./>) buttons
on the Keypad to confirm that the source component
operates properly.

- Remote control operation
Check that the remote control of the SOURCE 1 component
works by pressing any command button while pointing
the Remote Control toward the IR sensor of the Keypad.
Then check that the SOURCE 1 component operates
properly using the remote control.

7 Perform the test in each zone from zone 1 through

zone 6 by repeating Steps 3 to 6.

Setting up the Keypad

IR OUT

ANTENNA

VIDEO IN
AUDIO IN

SOURCE 1

KEYPAD

FIXED

PRE OUT

RL

SPEAKERS (CLASS II WIRING

ZONE 1

DVD player

VIDEO OUT
AUDIO OU T

L

R

LR

VIDEO OUT

VIDEO IN
AUDIO IN

IR OUT

VIDEO OUT
AUDIO OU T

L

R

SOURCE 2

FIXED

PRE OUT

)

SPEAKERS (CLASS II WIRING

IR OUT

VIDEO IN
AUDIO IN

SOURCE 3

KEYPAD

LR

VIDEO OUT

RL

ZONE 2

VIDEO OUT
AUDIO OU T

L

R

)

SPEAKERS (CLASS II WIRING

IR OUT

VIDEO OUT

VIDEO IN

AUDIO OU T

AUDIO IN

L

R

SOURCE 4

KEYPAD

LR

FIXED

PRE OUT

RL

ZONE 3

VIDEO IN
AUDIO IN

VIDEO OUT

IR OUT

VIDEO OUT
AUDIO OU T

L

R

SOURCE 5

PRE OUT

)

SPEAKERS (CLASS II WIRING

IR OUT

VIDEO IN
AUDIO IN

SOURCE 6

KEYPAD

LR

FIXED

RL

ZONE 4

OUT

IR IN

IR OUT IR OUT

VIDEO OUT

VIDEO OUT

VIDEO IN

AUDIO OUT

AUDIO OU T

AUDIO IN

L

L

R

R

SOURCE 7

KEYPAD

LR

VARIA BLE

VIDEO OUT

PRE OUT

RL

)

SPEAKERS (CLASS II WIRING

ZONE 5

TO SPEAKERS

R

L

MODE

SUB

IR OUT

VIDEO IN
AUDIO IN

SOURCE 8

VIDEO OUT

)

FROM AMPLIFIER

R

L

MAIN

COMMON

VIDEO OUT
AUDIO OU T

L

CONTROL

A1 II

R

KEYPAD

LR

VARIABLE

VIDEO OUT

PRE OUT

RL

SPEAKERS (CLASS II WIRING

ZONE 6

IN

DC IN

12V TRIGGER

123

456

)

STR

DVP

AUX

RS232C

SPEAKERS IMPEDANCE
USE 4-16

~AC IN

SP TV

SP

Ke

pad

29

Chapter 4

Precautions

Other
Information

This chapter provides you with
additional information that will help
you understand and maintain your
system.

On safety

• Should any solid object or liquid fall into the cabinet, unplug
the player and have it checked by qualified personnel before
operating it any further.

• The AC power cord must be changed only at a qualified
service shop.

• The unit is not disconnected from the AC power source
(mains) as long as it is connected to the wall outlet, even if the
unit itself has been turned off.

On power sources

• Before operating the unit, check that the operating voltage of
the unit is identical to that of your local power supply. The
operating voltage is indicated on the nameplate on the back of
the unit.

• If you are not going to use the unit for a long time, be sure to
disconnect it from the AC power source (mains). To disconnect
the mains lead, grasp the plug itself; never pull the cord.

On placement

• Place the unit in a location with adequate ventilation to
prevent heat build-up in the Main Unit.

• Do not place the unit on a soft surface such as a rug that might
block the ventilation holes on the bottom.

• Do not place the unit in a location near heat sources, or in a
place subject to direct sunlight, excessive dust, or mechanical
shock.

On adjusting the volume

• Do not turn up the volume too much while listening to audio
with very low input levels or no audio signals. If you do, the
speakers may be damaged when a peak level portion is played.

On cleaning

• Clean the cabinet, panel, and controls with a soft cloth slightly
moistened with a mild detergent solution. Do not use any type
of abrasive pad, scouring powder, or solvent, such as alcohol
or benzine.

If you have any questions or problems concerning the
Main Unit, please consult your nearest Sony dealer.

30

Troubleshooting

If you experience any of the following difficulties while
using the player, use this troubleshooting guide to help
you to remedy the problem. Should any problem persist,
consult your nearest Sony dealer.

There is no sound, no matter which component is
selected.

, Check that both the Main Unit and all components

are turned on.

, Check that all speaker cords are connected

correctly.

, Press MUTING to cancel the muting function.

There is no sound from a specific component.

, Check that the component is connected correctly to

the audio input jacks for that component.

, Check that the cord(s) used for the connection is

(are) fully inserted into the jacks on both the
receiver and the component.

There is no sound, or only a very low-level sound
is heard.

, Check that the speakers and components are

connected securely.

, Check that you have selected the correct

component on the Main Unit.

, Press MUTING if the muting function is activated.
, The protective device on the Main Unit has been

activated because of a short circuit. Turn off the
Main Unit, eliminate the short-circuit problem and
turn the power on again.

the Main Unit and placed in an appropriate
position.

, Make sure you have selected the correct function

on the Remote Control.

The IR Remote Control for the Keypad does not
function.

, Point the Remote Control at the remote sensor

on the Keypad.

, Remove any obstacles in the path between the

Remote Control and the Keypad.

, Replace both batteries in the Remote Control with

new ones, if they are weak.

, Check that you have selected the correct function

on the Remote Control.

The source component does not respond to the
Keypad operation.

, Check that the IR emitter is connected to the IR

OUT jack of the Main Unit.

, Check that the IR emitter is connected to the

corresponding IR OUT jack of the source
component.

, Check that the IR emitter is connected to the IR

sensor of the source component.

, Check that the remote codes have been

successfully learned by the Main Unit in the PC
SETP mode and the LEARN mode.

Other Information

The left and right sounds are unbalanced or
reversed.

, Check that the speakers and components are

connected correctly and securely.

, Adjust the balance parameters on each Keypad.

There is severe hum or noise.

, Check that the speakers and components are

connected securely.

, Check that the connecting cords are away from a

transformer or motor, and at least 3 meters away
from a TV set or fluorescent light.

, Move your TV away from the audio components.
, The plugs and jacks are dirty. Wipe them with a

cloth slightly moistened with alcohol.

There is no picture, or an unclear picture appears
on the TV screen or monitor.

, Select the appropriate input on the Main Unit.
, Set your TV to the appropriate input mode.
, Move your TV away from the audio components.

The RF Remote Control does not function.

, Make sure the RF antenna is connected securely to

31

Error Messages

Main Unit

If any of the messages below appear on the Display window of the Main Unit, check the following.

Message Cause Corrective action

PROTECTOR ZONE1 Protective device in zone 1 has been activated. Ask your nearest Sony dealer.
PROTECTOR ZONE2 Protective device in zone 2 has been activated. Ask your nearest Sony dealer.
PROTECTOR ZONE3 Protective device in zone 3 has been activated. Ask your nearest Sony dealer.
PROTECTOR ZONE4 Protective device in zone 4 has been activated. Ask your nearest Sony dealer.
PROTECTOR ZONE5 Protective device in zone 5 has been activated. Ask your nearest Sony dealer.
PROTECTOR ZONE6 Protective device in zone 6 has been activated. Ask your nearest Sony dealer.
FAN STOP
CONNECTION ERROR

STR
CONNECTION ERROR

DVD MEGA
CONNECTION ERROR

PC
CONNECTION ERROR

RF REMOTE
EEP ACCESS FAIL

Other Information

MEMORY FULL

The fan does not rotate. Ask your nearest Sony dealer.
A communication error with the AV receiver An error occurred due to an unsupported connection.

has (STR) occurred.
A communication error with the DVD MEGA An error occurred due to an unsupported connection.

CHANGER has occurred.
A communication error with the computer has An error occurred due to an unsupported connection.

occurred.
A confirmation error with the RF Remote Ask your nearest Sony dealer.

Control has occurred.
The Main Unit failed to access the EEPROM. Ask your nearest Sony dealer.
The Memory capacity for storing EEPROM Some remote codes cannot be learned even if the memory

code has been exceeded during the remote capacity used for learning has not been exceeded.
code learning.

Keypad

If any of the messages below appear on the display window of the Keypad, check the following.

Message Cause Corrective action

CONNECTION NOT The Keypad failed to communicate with Turn off the Main Unit and check the CAT5 connections.
ESTABLISHED the Main Unit.

PROTECTOR Protector is detected by the Main Unit. Turn off the Main Unit and check the speaker connections.
FAN STOP The fan of the Main Unit does not rotate. Turn off the Main Unit and check that the ventilation holes

PLEASE CHECK Mode selector switch setting is wrong. Check that the Mode switch on the rear panel of the
MODE SELECTOR Keypad is in the correct position.

CANNOT ACCESS NOW Multiple Keypads tried to access Wait for a few seconds and try again.

SOURCE NOT AVAILABLE! An inactive source was selected. Select the appropriate source connected to the Main Unit.
LOCKED BY OTHER ZONE

LOCKED BY MAIN ZONE

NOT USED

The selected source was locked by another You cannot operate a locked source until it is unlocked.
zone.

The selected source was locked by the main You cannot operate a locked source until it is unlocked.
zone.

An inactive button was selected. Some buttons are not assigned for certain sources.

are not covered.

the same source component.

ex.) PLAY cannot be operated in the TUNER position.

32

Specifications

CAV-M1000ES Main Unit

Audio (each channel)

Continuous average power output (FTC)
All channels: 30 W per channel min. RMS at 8 ohms,

any two channels driven from 20 Hz
to 20 kHz with no more than 0.09 %
HD.

Frequency response: 5 Hz to 70 kHz ± 3dB
Input sensitivity: 160 mV for 1 W output, 890 mV for full

output (30 W) with volume control

set to maximum.
Input impedance: 20 k ohms
Power output: 35 W RMS (4 - 8 ohms)
Signal-to-noise ratio: >92 dB (A-weighted )
Bass control range: 100 Hz ± 12 dB, 2 dB step
Treble control range: 10 kHz ± 12 dB, 2 dB step

Loop OUT/Pre OUT

Frequency response: 5 Hz to 55 kHz ± 3dB
THD @ 2 V: <0.08 %
Signal-to-noise ratio: 102 dB (A-weighted @ 2 V)

RM-TP100 RF Remote Control

Audio (each channel)

Operating system: Liquid crystal touch panel
Liquid crystal size: 3.8 inches

(256 ✕ 200 dots)

Liquid crystal type: Reflection system

(Monochrome type)

Touch panel: Resistant membrance system

Analog type

Power requirements: Rechargeable

(Ni-MH) battery

Maximum external dimensions:

166 mm ✕ 25 mm ✕ 126 mm (W ✕ D ✕
H, including projecting parts and
controls)

Mass: 392 g (Main unit only, including the

rechargeable battery)

Design and specifications are subject to change without notice.

Video

Input/output impedance:

75 ohm

Video insertion loss: 0 dB (50 Hz - 6 MHz)

General

12V trigger: 300mA max each zone, total 1.2A max
Power requirements: 120 V 60 Hz
Power consumption: 540 W
Dimensions: 430 mm ✕ 433 mm ✕ 175 mm

(W ✕ D ✕ H)
Mass: 24 kg

Other Information

33

Chapter 5

Appendix

This chapter provides you with
remote code lists and concise
information about operating the
system.

LEARN Mode Code List

34

Appendix

35

LEARN Mode Code List

Appendix

36

Index

A

AC IN 9,17
AC power cord 9, 17, 38
Adding a new remote key 21
Adjusting

Volume 38, 39, 40

Source input offset 23
ALL CLEAR 24
ALL ZONE MUTING button 7, 18
AMS button 10, 12
AUDIO IN jack 8, 16
AUDIO OUT jack8, 17

B

BACK button 7
Bass 28
Battery 38
BAUD RATE SET19

C

CANCEL button 7
CAT5 IN jack 11
CAT5 OUT jack 11
Charging the battery 38
CHANNEL +/- button 9
CHECK mode 22
CIS VERSION 24
CODE LEARNING 20
CONTROL A1II jack 8, 16
Cursor/ENTER button 7, 9, 12
Customizing

Keypad 28

Main Unit 22

D, E, F

DIMMER button 12
DISC

Button 12

DISC SEARCH 22

Information 22
DISPLAY button 12
Display window 7,10
ENTER button7,9,12
Error messages 32
EXPAND CODE 21

F1 button 12
F2 button 12
FIXED PRE OUT jack 9
FOLDER button 12
FROM AMPLIFIER jack 11

H, I

Hookup

AC power cord17
Keypad 17,27
IR emitter 17
Output components 27
RF Antenna 17
Source components 16
Speaker 27
TV monitor 27

Zone related cables 17
Initializing all the settings 24
INSTALLATION mode 22
Installing

Keypad 25

Main Unit 15

RF Antenna 15
IR IN jack 11
IR OUT jack 8,16,17
IR Remote Control 12,40
IR sensor 10

Appendix

K, L, M

Keypad 9, 25, 39
KEYPAD jack 9,17
LCD contrast 28
Learning the remote code 22
LEARN mode code list 34
LOCK button 10
Locking the settings 23
MENU button 12
MODE button 7
MODE switch 11
Mode indicator 7
MUTING button 9,10,12

37

Index

P

PAGE button 10, 12
PAUSE button 10, 12
PC SETUP 19
Planning the system 14
PLAY button 10, 12
POWER switch 7, 10
Precautions 30
PROGRAM button 7

R

Removing the Keypad 26
RS232C connector 7, 9, 16
RF Antenna 15 ,17
RF ANTENNA jack 8
RF Remote Control 9, 38

S

SCROLL button 10
SELECT button 10, 12
Selecting the source 18
SETUP LOCK 23
SLEEP button 12
SOURCE button 10, 12
SOURCE INPUT OFFSET 23

Appendix

SOURCE SELECT button 7
SPEAKERS jack 9, 17
Specifications 33
STOP button 10, 12
SYSTEM OFF switch 9

T, U, V, W, X, Y, Z

Testing

Components 29

Learned remote code 22
TOP MENU/GUIDE button 12
TO SPEAKERS jack 11
Treble28
Troubleshooting 31
TV CH button 12
TV/VIDEO button 12
TV VOL button 12
Using

IR Remote Control for the Keypad 40

Keypad 39

RF Remote Control 38
VARIABLE PREOUT jack 9
Version information 24
VIDEO IN jack 8,16
VIDEO OUT jack 8,9,17
Volume limits 28
VOLUME +/- button 9,10,12
ZONE VOLUME +/- button 7
ZONE button 7

Numeral

12 V TRIGGER jack 8,17

38

Using the RF Remote Control

Commands on the touch panel vary depending on the RF
Remote Control programming.

Turning the system on or off

1 Press SYSTEM OFF.

“ALL OFF”, “MAIN OFF”, and “RETURN” appear on
the touch panel.

2 Press “ALL OFF” when you want to turn off all

zones, and press “MAIN OFF” when you want to
turn off the main zone only.

Press “RETURN” when you want to cancel the
operation.

MUTING

MUTING

Turning the RF Remote Control off

Leave the RF Remote Control alone for a few
minutes.

The RF Remote Control turns off automatically.

Adjusting the volume

Press VOLUME +/– to the desired volume level.

Muting the volume

Press MUTING.

To cancel the muting, press MUTING again.

POWER OFF

SYSTEM OFF

Used for controlling
the source.

VOLUME +/–

VOLUME

Charging the internal battery

1 Connect the AC power cord of the charger cradle to

the wall outlet.

2 Place the RF Remote Control on the charger cradle.

The internal battery starts charging.

2

1

To the wall outlet

CHANNEL

Used for controlling
the source.

Appendix

39

Using the Keypad

Press POWER to turn the Keypad on.

The source components also turn on.
To turn the Keypad off, press POWER again.
When the last zone is turned off, all the source
components also turn off.

1 Press SELECT next to the desired source displayed

2 Press any of the following buttons to control the

Receives IR signals from the
IR Remote Control for Keypad
(supplied).

Press to select a menu on the
display on the LCD, such as a
source menu, disc title list,

Appendix

tuner preset station list, etc.
Press to return to the

previous menu or to view the
current status of the disc title
list or the preset station list.
If there is no list, only a
source name will be
displayed.

Press to lock the selected
source component.

Turning the Keypad on or off

Selecting and controlling the source

in the LCD window.

The selected source is activated.

activated source component.

H: Operates the selected source component.
X: Pauses the playback.
x: Stops the playback.
./>: Locates a specific track or preset station.

PAGE SOURCE MUTING

POWER

Adjusting the volume

Press VOLUME +/– to the desired listening level.

Muting the volume

Press MUTING.

T o cancel the muting, press MUTING again or VOLUME +.

Shows the selected source,
zone volume level, zone
and system status, and
other system status
information.

Press to select a menu on
the display on the LCD,
such as a source menu, disc
title list, tuner preset
station list, etc.

Press to scroll the LCD menu.

Press to mute the speaker
output from the Keypad.

Press to return to the home
screen, while the selected

VOLUME

source component is still
enabled.

Press to increase/decrease
the volume in a zone.

H: Press to operate the

selected source
component.

X: Press to pause playback.
x: Press to stop playback.
./>:Locates a specific

track or preset station.

Press to turn the Keypad
on/off.

40

Using the IR Remote Control for the Keypad

Buttons marked in grey are used to control the source
components.

Inserting batteries into the Remote
Control

Insert two R06 (size-AA) batteries into the battery
compartment with the + and – correctly oriented to the
markings. When using the Remote, point it at the IR
sensor

z

Under normal conditions, the batteries should last for about six
months. When the remote no longer operates the player, replace
both batteries with new ones.

Notes

• Do not leave the Remote Control in an extremely hot or a

• Do not drop any foreign object into the Remote Control casing,

• Do not use a new battery with an old one.

• Do not expose the IR sensor to direct sunlight or lighting

• If you do not intend to use the Remote Control for an extended

on the Keypad.

When to replace the batteries

humid place.

particularly when replacing the batteries.

equipment. Doing so may cause a malfunction.

period of time, remove the batteries to avoid possible damage
from battery leakage and corrosion.

2 Press any of the following buttons to control the

activated source component.

H: Operates the selected source component.
X: Pauses playback.
x: Stops playback.
./>: Locates a specific track or preset station.
m/M: Locates a section you want to play within a

track.

Adjusting the volume

Press MASTER VOL +/– to the desired volume level.

Muting the volume

Press MUTING.

To cancel the muting, press MUTING again or VOLUME +.

SLEEP DIMMER

1234

5678

90

SELECT

./>

TV

>10

SELECT

LOCK DISC

PAGE SOURCE

UP

DOWN

ENTER

m/M

Appendix

Turning the Keypad on or off

Press ?/1 to turn the Keypad on.

The source components also turn on.
To turn the Keypad off, press ?/1 again.
When the last active zone is turned off, all the source
components also turn off.

Selecting and controlling the source

1 Press SELECT next to the desired source displayed

in the LCD window.

The selected source is activated.

X
H

TOP MENU/

GUIDE

TV VOL TV CH FOLDER F1

MENU MUTING

RETURN/EXITDISPLAY

TV/VIDEO F2

x

MUTING

VOLUME

VOLUME

41

Appendix

42

Appendix

43

Información complementaria

Sony Corporation Printed in Malaysia

44