Sony AIRLINK HELIX User Manual

AirLink Helix
User Guide
2140847
Rev 3.0D
Preface
Important Notice
Safety and Hazards
READ ALL SAFETY AND OPERATING INSTRUCTIONS BEFORE OPERATING THE PRODUCT.
Warning:
NOT EXPOSE THIS DEVICE TO RAIN OR MOISTURE. DO NOT EXPOSE THIS PRODUCT TO DRIPPING OR SPLASHING. NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE DEVICE.
Caution:
THAN THAT CONTAINED IN THE INSTALLATION AND TROUBLESHOOTING INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO. REFER ALL SERVICING TO QUALIFIED SERVICE PERSONNEL.
FOR INDOOR USE ONLY. TO PREVENT FIRE OR SHOCK HAZARD, DO
DO NOT OPEN THE UNIT. DO NOT PERFORM ANY SERVICING OTHER
Caution:
PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
It is recommended that the customer install an AC surge arrestor in the AC outlet to which this device is connected. This is to avoid damaging the equipment by local lightning strikes and other electrical surges.
Only use twisted pair Ethernet cables with RJ-45 connectors that conform to FCC standards in the Ethernet ports. Do not plug a telephone cable (RJ-11) into any Ethernet (RJ-45) port on your device.
Installation of this product must be in accordance with national wiring codes.
To clean, wipe this device with a clean, dry cloth. Never use cleaning fluid or similar chemicals. Do not spray cleaners directly on the unit or use forced air to remove dust.
Do not use attachments not recommended by the device manufacturer.
To avoid injury from falling equipment, do not place this product on an unstable surface.
This device should be situated away from heat sources and products that produce heat.
CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE
Rev 3.0D May.10 3
AirLink Helix User Guide
All safety and operating instructions should be retained for future reference.
Do not use onboard aircraft or in hazardous locations such as gas stations or explosive environments.
Not designed, manufactured or intended for machinery, medical, or industrial applications or for any other application may be hazardous.
Do not move or touch the antennas while the device is on. Device should be located at least 20 centimeters (8 inches) away from any human body in order to meet FCC exposure limits.
Do not operate while driving.
Regulatory Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference; and
2. This device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
The device that accompanies this software can radiate radio frequency energy. If not used in accordance with the instructions given in the User Guide, the device may cause harmful interference with other communications devices (for example radios, televisions, phones, etc.).
Any changes or modifications not expressly approved by Sierra Wireless could void the user's authority to operate this device.
Sierra Wireless America, 39677 Eureka Drive, Newark, CA USA, 94560 (510.624.4900).
Open Source Certain components of the software included with the Helix RT are subject to the
GNU General Public License ("GPL"), the Lesser GNU General Public License ("LGPL"), or other "open source" or "free software" licenses ("Open Source Software"). Some of the Open Source license is owned by third parties. Each item of Open Source Software is licensed under the terms of the end-user license that accompanies such Open Source Software. Nothing in this document limits your
4 2140847
Preface
rights under, or grants you rights that supersede, the terms and conditions of any applicable Open Source License. In particular, nothing in this document restricts your right to copy, modify, and distribute that Open Source Software subject to the terms of Open Source License. As required by the terms of the GPL and LGPL or any other applicable Open Source License, Sierra Wireless makes the Open Source Software available to the public in source code form on a CD. To receive a CD, please contact customer support.
The following Open Source Software is included with the Helix RT.
GPL and LGPL Software. The Helix RT is provided with the following software licensed under the GPL and LGPL. A copy of the GNU GPL license is available from the Free Software Foundation (http://www.gnu.org).
· BusyBox from Erik Andersen (http://www.busybox.net)
· Host AP driver from Jouni Malinen (http://hostap.epitest.fi)
· IPtables from Harald Welte and others (http://www.netfilter.org)
· Linux operating system version 2.4.20
· Openswan from Xelerance Corporation (http://www.openswan.org)
· PPP from Paul Mackerras (http://www.samba.org/ftp/unpacked/ppp/
· README)
· SPLASH from Willem de Bruijn (http://splash-snap.sourceforge.net)
· Updatedd from Philipp Benner (http://www.philipp-benner.de/updatedd)
Other Open Source Software. The Helix RT is provided with the following
software licensed under BSD licenses or other Open Source Licenses. The software and license details are available from the referenced web sites.
· Internet Software Consortium DHCP Server (http://www.isc.org)
· Net-SNMP from the NET-SNMP Project (http://www.net-snmp.org)
· OpenSSH from the OpenBSD Project (http://www.openssh.com)
· thttpd from Jef Poskanzer (http://www.acme.com)
Patents Portions of this product may be covered by some or all of the following US
patents:
5,515,013 5,629,960 5,845,216 5,847,553 5,878,2345,890,0575,929,8156,169,884 6,191,741 6,199,168 6,339,405 6,359,591 6,400,3366,516,2046,561,8516,643,501 6,653,979 6,697,030 6,785,830 6,845,249 6,847,8306,876,6976,879,5856,886,049 6,968,171 6,985,757 7,023,878 7,053,843 7,106,5697,145,2677,200,512D442,170 D459,303
and other patents pending.
Copyright 2004-2009 Sierra Wireless America, Inc.
Trademarks AirLink™ and AceWare™ are trademarks of Sierra Wireless.
Helix RT ™ is a trademark os Sierra Wireless.
Windows
Other trademarks are the property of the respective owners.
Rev 3.0D May.10 5
®
is a registered trademark of Microsoft Corporation.
AirLink Helix User Guide
Contact Information
Support Desk: Phone: 1-877-231-1144
Hours: 5:00 AM to 5:00 PM Pacific Time,
Monday to Friday, except US Holidays
E-mail: support@sierrawireless.com
Sales Desk: Phone: 1-510-624-4200
1-604-232-1488
Hours: 8:00
E-mail: MobileandM2Msales@sierrawireless.com
Post: Sierra Wireless America
39677 Eureka Drive Newark, CA USA 94560
Sierra Wireless 13811 Wireless Way Richmond, BC Canada V6V 3A4
Fax: 1-510-624-4299
1-604-231-1109
AM to 5:00 PM Pacific Time
Web: www.sierrawireless.com
Consult our website for up-to-date product descriptions, documentation, application notes, firmware upgrades, troubleshooting tips, and press releases:
www.sierrawireless.com
Revision number
1.x 2009 AirLink Helix documentation draft created.
2.x 2009 AirLink Helix documentation revised.
3.x 2009 USB Chapter added.
Release date
Changes
6 2140847
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
What’s Included with the AirLink Helix? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
What Else Do You Need to Get Started?. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Getting Going (the quick version). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
CDMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
GSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Connecting a Computer to the AirLink Helix . . . . . . . . . . . . . . . . . . . . . . . . . .7
Connecting Through Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Connecting Through Wi-Fi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Where to Find More Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Physical Interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Turning On the AirLink Helix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Status Lights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Cellular Antennas. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Wi-Fi Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Reset Button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Power Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
SIM Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Remove the SIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
USB Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
USB Modem connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Configuring AirLink Helix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
ACEmanager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Rev 3.0D May.10 1
Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Home . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
WAN/Cellular . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
LAN/WiFi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
VPN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
About . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Configuring WAN/Cellular . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
WAN/Cellular . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
WAN Failover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
How it works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
IP Passthrough . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Contents
Configuring LAN/WiFi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
LAN/WiFi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Addressing/VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
WiFi Global . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Shared WEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
WPA/WPA2 Personal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
WPA Enterprise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
WiFi 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Global DNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
VRRP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Configuring AirLink Helix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
VPN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
VPN 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
VPN 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Rev 3.0D May.10 2
Contents
Configuring Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Port Forwarding and DMZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Port Filtering - Outbound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
MAC Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Configuring Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
ACEnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
ACEmanager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Dynamic DNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Landing Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Management (“SNMP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Configuring Admin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Admin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Debug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
WAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Routing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Administration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Rev 3.0D May.10 3
AirLink Helix User Guide
Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Federal Communications Commission Notice (FCC United States) . . . . 53
Industry Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Antenna Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
RF Exposure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
EU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
WEEE Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
4 2140847

1: Introduction

What’s Included
with the AirLink Helix?
What Else Do You
Need to Get Started?
Getting Going (the
quick version)
The AirLink Helix enables computers and other devices to connect quickly and easily to the Internet and remote enterprise networks using cellular data networks.
This User Guide provides basic instructions on how to configure and operate your AirLink Helix. For additional support please visit www.sierrawireless.com/support.

What’s Included with the AirLink Helix?

AirLink Helix RT kit
AirLink Helix RT cellular router
User Guide
Outlet power adapter
Wi-Fi (optional depending on the kit)
Antennas (optional depending on the kit)
1

What Else Do You Need to Get Started?

An active data account with your cellular provider is required. Contact your cellular carrier or reseller if you have data account related queries.
Note: Please also read the terms and conditions of your cellular service to ensure that your rate plan is appropriate for use with the AirLink Helix.
At least one computer that supports Ethernet or Wi-Fi networking.
A web browser such as Internet Explorer 6 or later for Windows, Firefox 1.5, or Safari.
Rev 3.0D May.10 5
AirLink Helix User Guide

Getting Going (the quick version)

The AirLink Helix is designed to be simple to use. No additional software is required for most users. The remainder of the User Guide provides complete instructions for using the device.

CDMA

If you have a CDMA device, please follow the instructions as below:
1. Plug the AirLink Helix power adapter into the power connector on the back panel of the AirLink Helix. Wait approximately two minutes to allow the AirLink Helix and modem to initialize.
2. Connect your computer to the AirLink Helix with an ethernet cable. Users can also connect with Wi-Fi using “helix” as the default network name.
3. If the modem is not automatically detected, and if you are a first time user, you may need to configure your cellular modem through the WAN page in the ACEmanager with your web browser at 192.168.2.1. The username is admin and default password is 12345. For more details on configuring the AirLink Helix, refer to the chapter titled “Using the ACEmanager.”
GSM
If you have a GSM device, please follow the instructions as below:
1. Insert a SIM card into the SIM slot on the front of the Helix.
2. Plug the AirLink Helix power adapter into the power connector on the back
panel of the AirLink Helix. Wait approximately two minutes to allow the AirLink Helix and modem to initialize.
3. Connect your computer to the AirLink Helix with an ethernet cable. Users can also connect with Wi-Fi using “helix” as the default network name.
4. If the modem is not automatically detected, and if you are a first time user, you may need to configure your cellular modem through the WAN page in the ACEmanager with your web browser at 192.168.2.1. The username is admin and default password is 12345. For more details on configuring the AirLink Helix, refer to the chapter titled “Using the ACEmanager.”
Have more questions? Look through this manual for more information or contact Sierra Wireless support at http://www.sierrawireless.com/support.
6 2140847
2: Connecting a Computer to the AirLink
Serial Port
LAN Ethernet
USB port
USB Port
LAN/WAN Ethernet
Power
Helix
Connecting
Through Ethernet
Connecting
Through Wi-Fi
Where to Find More
Help
Any laptop, desktop, handheld, printer, or other computing device that supports Ethernet (or optional Wi-Fi) can connect to the AirLink Helix. If your computer supports these common network interfaces, you don’t need to install any additional software to connect to the AirLink Helix.
Before connecting multiple devices to the AirLink Helix for the first time, it is a good idea to connect one computer first and verify that the Product Name is successfully connected to the Internet. You may need to use AirLink Helix ACEmanager to verify that the Helix device is properly configured. See the “Configuring AirLink Helix” chapter for more information.
2
Figure 2-1: Helix: Ports on the backplate

Connecting Through Ethernet

To connect to the AirLink Helix using Ethernet, simply plug one end of an Ethernet cable into your computer, and plug the other end into either of the Ethernet ports on the AirLink Helix.
There are two Ethernet ports on the Helix. In most configurations, both can be used for LAN connections. In WAN failover mode, one is used for a WAN port to connect to another Internet service like a DSL or cable modem.
Rev 3.0D May.10 7
Make sure your computer is setup for DHCP addressing. To setup the AirLink Helix for static IP addressing, refer to the LAN Page section in “Using the ACEmanager”.
AirLink Helix User Guide

Connecting Through Wi-Fi

Wi-Fi is available as an option on some versions of the Helix RT.
To connect wirelessly to the AirLink Helix using a Wi-Fi equipped computer, simply select the network name “helix” using the Wi-Fi connection software provided with your operating system or Wi-Fi network interface.
You can customize the network name and other Wi-Fi configuration options using the LAN/Wi-Fi page in the ACEmanager. For more information, see the “Using the ACEmanager” chapter.
Note: If you don’t change the default security settings in the ACEmanager for the AirLink Helix, the AirLink Helix is accessible to any Wi-Fi device. For information about Wi-Fi security, see the Security Page section in the “Using ACEmanager” chapter.
The AirLink Helix Wi-Fi network is based on the 802.11b/g. By default you can also use computers equipped with 802.11b Wi-Fi hardware because 802.11g is backwards compatible with 802.11b.
If you have trouble connecting automatically to the AirLink Helix using Wi-Fi, try the following:
Make sure the “helix” network name is selected in the list of available networks with your computer’s Wi-Fi connection software.
Turn your computer’s Wi-Fi connection off and then on again.
Restart your computer.
Check to see that your computer’s network configuration is consistent with the
configuration of the AirLink Helix. The default AirLink Helix configuration requires your computer to use a DHCP connection.
For Windows XP users, check to see that you have Service Pack 2 or higher installed. To determine if you have Service Pack 2 installed, open the Control Panel and then open the System application.
Change the Wi-Fi channel in the AirLink Helix ACEmanager. You may be encountering interference on a certain channel.
Try turning off WEP or WPA encryption in the ACEmanager. If you can connect when encryption is turned off, you may be entering incorrect WPA or WEP login information into your computer or device.

Where to Find More Help

The Ethernet, Wi-Fi, and TCP/IP network interfaces used by the AirLink Helix comply with industry standards. Connection issues may be related to the proper use of these standards and not the AirLink Helix itself. For additional help connecting your computer or device to the AirLink Helix, please refer to the networking instructions provided by your computer’s operating system.
Please contact Sierra Wireless support for further Helix RT related queries.
8 2140847

3: Hardware Overview

Physical Interfaces
Turning On the
AirLink Helix
Status Lights
Cellular Antennas
Wi-Fi Antennas
Reset Button
Power Connector
SIM Slot

Physical Interfaces

The AirLink Helix has the following physical interfaces and connection methods:
Two cellular SMA antenna connectors
802.11b/g Wi-Fi (optional)
Two Wi-Fi SMA antenna connectors (optional)
2 host USB ports
2 Ethernet ports
1 serial port
Note: Software currently does not support USB services. Do not plug unsupported devices into the USB ports.
3
Note: An ALEOS update support USB is expected by September 2009.
Note: Serial connection is for modem programming purposes only.

Turning On the AirLink Helix

The AirLink Helix powers on as soon as it is plugged in to the power outlet. The AirLink Helix power port is located on the back of the device. To turn the device off, simply unplug the power adapter.
For use in a vehicle, a vehicle power adapter is available as an optional accessory.

Status Lights

The AirLink Helix has three lights on the front faceplate that indicate status and help initial troubleshooting. The green LED on the left, is lit whenever Helix is plugged in. The middle green LED indicates cellular signal strength. The right green LED indicates WWAN activity.There are three modes:
Rev 3.0D May.10 9
AirLink Helix User Guide
3G
Signal Strength
WWAN
Status
Figure 3-1: Status LEDs

LEDs

The LED patterns in the Helix are as follows:
(Left) – 3G
Off : 3G connection is not active
On : 3G connection is active
(Middle) – Signal Strength (RSSI)
On Solid : Equal to or stronger than -69dBm (excellent signal strength)
Fast Blink : -70 to -79dBm
Normal Blink : -80 to -89dBm
Slow Blink : -90 to -99dBm
Off : Equal to or weaker than -100dBm (no signal strength)
(Right) – WWAN Status
Off : No cell module detected
Blinking : cellular module detected, communicating with the Helix CPU. This
LED is hardware dependent and may blink differently depending on the installed cellular module.

Cellular Antennas

The AirLink Helix requires two cellular antennas, as shown in Figure 3-2. Depending on your Helix kit, antennas may or may not be included.
10 2140847
Hardware Overview
Cellular Antennas
Note: This device is not intended for use within close proximity of the human body. Antenna installation should provide for at least a 20 cm separation from the operator.
The Helix will work with most dual band cellular antennas with SMA connectors. Connect antennas directly to the connectors found on the sides of the Helix.
Note: When using a cable to an antenna placed away from the Helix, minimize the length of your cable. All gain from a more advantageous antenna placement can be lost with a long cable to the device. Each external antenna used with an extension cable, should be located 20cm apart from any other antenna.
Figure 3-2: Cellular Antennas
Note: Use all four antennas for diversity . Using only one cell antenna or one Wi-Fi antenna can cause degraded performance.
The optimal placement of the cellular antenna is upright.
Rev 3.0D May.10 11
AirLink Helix User Guide

Wi-Fi Antennas

Reset Button

Wi-Fi Antennas
The antennas on the back of the Helix are for transmitting and receiving Wi-Fi signals. Connect antennas directly to the connectors found at the back of the Helix.
Note: Optimal antenna performance can be achieved by orienting the WiFi antennas horizontally.
Figure 3-3: Wi-Fi Connection
Reset Button
The reset button is a small hole located in on the front faceplate of the Helix. This button provides a quick way to turn the Helix power off and back on. Simply insert a paper clip or similar object into the hole to press the reset button.
In some cases the Airlink Helix may need to be reset to defaults. This will reset any custom settings and connection information. If the ACEmanager password has been forgotten or is unable to be accessed, the Airlink Helix can be reset during the bootup process by pressing the reset button for just 10 seconds.
Figure 3-4: Helix: Reset Button
12 2140847
Hardware Overview
Power adapter

Power Connector

Helix comes with a switching adapter. The power connector is located on the back plate of the Helix.
Figure 3-5: Power Connector

SIM Slot

Note: This section applies to Helix with GSM technology only.
To insert the SIM in to the SIM slot, follow the instructions as below:
1. Carefully remove the SIM card from the card you received.
Figure 3-6: SIM card
2. Gently press the SIM to click it into place.
Figure 3-7: Insert SIM
3. When the SIM card is fully inserted, it will lock into the holder with a click sound.
Rev 3.0D May.10 13
Loading...
+ 44 hidden pages