Sony 4-127-735-12-1, KDL-19S55xx User Manual

LCD Digital Colour TV

Operating Instructions

KDL-32S55xx KDL-26S55xx KDL-22S55xx KDL-19S55xx

NOTICE FOR CUSTOMERS IN THE UNITED KINGDOM

A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience. Should the fuse in the plug supplied need to be replaced with the same rating of fuse approved by ASTA or BSI to BS 1362 (i.e., marked with or ) must be used. When an alternative type of plug is used it should be fitted with the same rating of fuse, otherwise the circuit should be protected by a 10 AMP FUSE at the distribution board. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station.

FUSE

The manufacturer of this product is Sony Corporation, 1-7-1 Konan Minato-ku Tokyo, 1080075 Japan. The Authorized Representative for EMC and product safety is Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents.

Trademark information

• is a registered trademark of the DVB Project

• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

About the model name in this manual

The “xx” that appears on the model name, corresponds to two numeric digits related to design or colour variation.

FUSE

How to replace the fuse

Open the fuse compartment with a blade screwdriver, and replace the fuse. Please refer to the illustration that actually equipped with

the product.

Introduction

Thank you for choosing this Sony product. Before operating the TV, please read this manual thoroughly and retain it for future reference.

Notice for Digital TV function

• Any functions related to Digital TV ( ) will only work in countries or areas where DVB-T (MPEG2) digital terrestrial signal s are broadcasted. Please confirm with your local dealer if you can receive a DVB-T signal where you live.

• Although this TV set follows DVB-T specifications, compatibility with future DVB-T digital terrestrial broadcasts cannot be guaranteed.

• Some Digital TV functions may not be available in some countries.

Table of Contents

Start-up Guide 4

Safety information.............................................................................................................9

Precautions......................................................................................................................11

Overview of the remote ..................................................................................................12

Overview of the TV buttons and indicators ..................................................................13

Watching TV

Watching TV ....................................................................................................................14

Using the Digital Electronic Programme Guide (EPG) .......................................16

Using the Digital Favourite list .............................................................................17

Using Optional Equipment

Connecting optional equipment ....................................................................................18

Viewing pictures from connected equipment ..............................................................20

Playing Back Photo/Music via USB...............................................................................21

Using control for HDMI ...................................................................................................22

Using MENU Functions

Navigating through menus.............................................................................................23

Settings ............................................................................................................................24

Additional Information

Installing the Accessories (Wall-Mount Bracket) .........................................................31

Specifications ..................................................................................................................34

Troubleshooting..............................................................................................................36

: for digital channels only

Start-up Guide

1: Checking the accessories

Remote RM-ED017 (1) Size AA batteries (R6 type) (2) Stand (1) Screws for stand (KDL-32S55xx/KDL-26S55xx (4), KDL-22S55xx/KDL-19S55xx (3))

To insert batteries into the remote

Push and slide to open.

• Observe the correct polarity when inserting batteries.

• Do not use different types of batteries together or mix old and new batteries.

• Dispose of batteries in an environmentally friendly way. Certain regions may regulate disposal of batteries. Please consult your local authority.

• Handle the remote with care. Do not drop or step on it, or spill liquid of any kind onto it.

• Do not place the remote in a location near a heat source, a place subject to direct sunlight, or a damp room.

KDL-32S55xx/KDL-26S55xx

Accessory bag Screws

Table-Top Stand

TV unit

KDL-22S55xx/KDL-19S55xx

Accessory bag

Table-Top Stand

Screws

2: Attaching the stand

Follow the assembling steps required to place on a TV stand.

1 Take out the Table-Top Stand and screws

from the carton. The screws are found in the accessory bag.

TV unit

2 Gently slide the TV unit onto the neck of

the Table-Top Stand and align the screws holes.

KDL-32S55xx/KDL-26S55xx

Rear of TV

KDL-22S55xx/KDL-19S55xx

Rear of TV

• When you carry the TV, place your hand as illustrated and hold it securely, see page 9. Do not put stress on the LCD panel and the frame around the screen.

• Be careful not to pinch your hands or the mains lead when you install the TV to the Table-Top Stand.

3 Use the supplied screws to attach the TV

unit to the Table-Top Stand.

KDL-32S55xx/KDL-26S55xx

Screws

3: Connecting an aerial/VCR/DVD recorder

• This product has been tested and found to compliant with the limits set out in the EMC Directive for using connection cables not longer than 3 meters (9.8 feet).

Connecting an aerial only

Coaxial cable

Connecting an aerial/VCR/DVD recorder with SCART

Start-up Guide

KDL-22S55xx/KDL-19S55xx

Screws

• If an electric screw driver is used, set the torque to tighten at approximately 1.5 N·m {15 kgf·cm}.

AV1 AV2

Coaxial cable

Scart lead

Coaxial cable

VCR/DVD recorder

• AV1 outputs available only for analogue TV.

• AV2 outputs to the current screen (except PC, HDMI, Component 1080i).

Continued

Connecting an aerial/VCR/DVD recorder with HDMI

KDL-32S55xx/KDL-26S55xx

Coaxial

cable

4: Preventing the TV from toppling over

HDMI cable

Coaxial cable

VCR/DVD recorder

KDL-22S55xx/KDL-19S55xx

HDMI cable

Coaxial

cable

1 Install a wood screw (4 mm in diameter,

not supplied) in the TV stand.

2 Install a machine screw (M4 × 14 mm, not

supplied) and a nut (M4, not supplied) from the bottom of the Table-Top Stand into the screw hole of the TV. Adjust a strong cord line weight accordingly, to secure the machine screw and nut.

• Be sure to secure a machine screw and a nut.

3 Tie the wood screw and the machine

screw with a strong cord.

• An optional Sony support belt kit is used to secure the TV. Contact your nearest Sony Service Centre to purchase a kit. Have your TV model name ready for reference.

5: Bundling the cables

You can bundle the connecting cables as illustrated below.

VCR/DVD recorder

Coaxial cable

1 2 3

• Do not bundle the mains lead with other connecting cables.

6: Adjusting the

3° 8°

RETURN TOOLS

GUIDE

AUDIOSCENE

ANALOGDIGITAL

viewing angle of the TV

KDL-22S55xx/KDL-19S55xx only

This TV can be adjusted within the angle shown below.

Adjust the angle back and forth (tilt)

Right view

Front

• When you turn on the TV, the power indicator light up in green.

3 Press F/f to select the language

displayed on the menu screens, then

press

Auto Start-up

Language

Country

Location

Select: Confirm:

English

Nederlands

Italiano

Deutsch

4 Press F/f to select the country/region in

which you will operate the TV, then press

Start-up Guide

Selecting the language, country/region and location

3,4,5

Auto Start-up

Language

Country

Location

Select:Back: Confirm:

United Kingdom

Ireland

Nederland

Luxembourg

France

Italia

If the country/region which you want to use on the TV does not appear in the list, select “-” instead of a country/region.

5 Press F/f to select the location type in

which you will operate the TV, then press .

Auto Start-up

Language

Country

Location

Home

Shop

1 Connect the TV to your mains socket

(220-240V AC, 50Hz).

2 Press 1 on the side of the TV.

When you turn on the TV for the first time, the Language menu appears on the screen.

Select:Back: Confirm:

In Shop mode, some settings will be periodically reset for Shop usage.

This option selects the initial picture mode appropriate for the typical lighting condition in these environments.

8: Auto-tuning the TV

1 Before you start auto-tuning the TV, insert

a pre-recorded tape into the VCR connected to the TV (page 5) and start play back.

The video channel will be located and stored on the TV during auto-tuning. If no VCR is connected to the TV, skip this step.

2 Press .

Auto Tuning

Do you want to start Auto Tuning?

Back: Start:

5 Press MENU to exit.

The TV has now tuned in all the available channels.

Detaching the TableTop Stand from the TV

• Do not remove the Table-Top Stand for any reason other than to wall-mount the TV.

KDL-32S55xx/KDL-26S55xx

The TV starts searching for all available digital channels, followed by all available analogue channels. This may take some time, so do not press any buttons on the TV or remote while proceeding.

If a message appears for you to confirm the aerial connection

No digital or analogue channels were found. Check all the aerial connections and press to start auto-tuning again.

3 When the Programme Sorting menu

appears on the screen, follow the steps of “Programme Sorting” (page 27).

If you do not change the order in which the analogue channels are stored on the TV, go to next step.

4 When the Eco Preset menu appears on

the screen, if you press “Yes,” the “Eco” settings are changed to recommended values to reduce power consumption.

Eco Preset

Do you want to use the Eco Preset?

Choosing "YES" will reduce power consumption.

Power Saving

Idle TV Standby

PC Power Management

Yes

Reduce

3 h

Table-Top Stand

KDL-22S55xx/KDL-19S55xx

Table-Top Stand

Safety information

Installation/Set-up

Install and use the TV set in accordance with the instructions below in order to avoid any risk of fire, electrical shock or damage and/or injuries.

Installation

• The TV set should be installed near an easily accessible mains socket.

• Place the TV set on a stable, level surface.

• Only qualified service personnel should carry out wall installations.

• For safety reasons, it is strongly recommended that you use Sony accessories, including:

KDL-32S55xx:

– Wall-mount bracket SU-WL500

KDL-26S55xx/KDL-22S55xx/KDL-19S55xx:

– Wall-mount bracket SU-WL100

• Be sure to use the screws supplied with the Wall-mount bracket when attaching the mounting hooks to the TV set. The supplied screws are designed so that they are 8 mm to 12 mm in length when measured from the attaching surface of the mounting hook. The diameter and length of the screws differ depending on the Wall-mount bracket model. Use of screws other than those supplied may result in internal damage to the TV set or cause it to fall, etc.

8 mm-12 mm

Transporting

• Before transporting the TV set, disconnect all cables.

• Two or more people are needed to transport a large TV set.

• When transporting the TV set by hand, hold it as shown below. Do not put stress on the LCD panel and the frame around the screen.

• When lifting or moving the TV set, hold it firmly from the bottom.

• When transporting the TV set, do not subject it to jolts or excessive vibration.

• When transporting the TV set for repairs or when moving, pack it using the original carton and packing material.

KDL-32S55xx KDL-26S55xx/KDL-22S55xx/

KDL-19S55xx

Ventilation

• Never cover the ventilation holes or insert anything in the cabinet.

• Leave space around the TV set as shown below.

• It is strongly recommended that you use a Sony wallmount bracket in order to provide adequate aircirculation.

Screw (supplied with the Wall-mount bracket)

Mounting Hook

Hook attachment on rear of TV set

Installed on the wall

30 cm

10 cm

Leave at least this space around the set.

Installed with stand

30 cm

10 cm10 cm

Leave at least this space around the set.

10 cm

Continued

6 cm

• To ensure proper ventilation and prevent the collection of dirt or dust: – Do not lay the TV set flat, install upside down,

backwards, or sideways.

– Do not place the TV set on a shelf, rug, bed or in a

closet.

– Do not cover the TV set with a cloth, such as curtains,

or items such as newspapers, etc.

– Do not install the TV set as shown below.

Air circulation is blocked.

Wall

Air circulation is blocked.

Wall

Prohibited Usage

Do not install/use the TV set in locations, environments or situations such as those listed below, or the TV set may malfunction and cause a fire, electrical shock, damage and/or injuries.

Location:

Outdoors (in direct sunlight), at the seashore, on a ship or other vessel, inside a vehicle, in medical institutions, unstable locations, near water, rain, moisture or smoke.

Environment:

Places that are hot, humid, or excessively dusty; where insects may enter; where it might be exposed to mechanical vibration, near flammable objects (candles, etc). The TV set shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the TV.

Situation:

Do not use when your hands are wet, with the cabinet removed, or with attachments not recommended by the manufacturer. Disconnect the TV set from mains socket and aerial during lightning storms.

Mains lead

Handle the mains lead and socket as follows in order to avoid any risk of fire, electrical shock or damage and/or injuries:

– Use only mains leads supplied by Sony, not other

suppliers. – Insert the plug fully into the mains socket. – Operate the TV set on a 220-240 V AC supply only. – When wiring cables, be sure to unplug the mains lead

for your safety and take care not to catch your feet on

the cables. – Disconnect the mains lead from the mains socket

before working on or moving the TV set. – Keep the mains lead away from heat sources. – Unplug the mains plug and clean it regularly. If the

plug is covered with dust and it picks up moisture, its

insulation may deteriorate, which could result in a

fire.

Notes

• Do not use the supplied mains lead on any other equipment.

• Do not pinch, bend, or twist the mains lead excessively. The core conductors may be exposed or broken.

• Do not modify the mains lead.

• Do not put anything heavy on the mains lead.

• Do not pull on the mains lead itself when disconnecting the mains lead.

• Do not connect too many appliances to the same mains socket.

• Do not use a poor fitting mains socket.

Broken pieces:

• Do not throw anything at the TV set. The screen glass may break by the impact and cause serious injury.

• If the surface of the TV set cracks, do not touch it until you have unplugged the mains lead. Otherwise electric shock may result.

When not in use

• If you will not be using the TV set for several days, the TV set should be disconnected from the mains for environmental and safety reasons.

• As the TV set is not disconnected from the mains when the TV set is just turned off, pull the plug from the mains to disconnect the TV set completely.

• However, some TV sets may have features that require the TV set to be left in standby to work correctly. The instructions in this manual will inform you if this applies.

For children

• Do not allow children to climb on the TV set.

• Keep small accessories out of the reach of children, so that they are not mistakenly swallowed.

If the following problems occur...

Turn off the TV set and unplug the mains lead immediately if any of the following problems occur. Ask your dealer or Sony service centre to have it checked by qualified service personnel.

When:

– Mains lead is damaged. – Poor fitting of mains socket. – TV set is damaged by being dropped, hit or having

something thrown at it.

– Any liquid or solid object falls through openings in

the cabinet.

Precautions

Viewing the TV

• View the TV in moderate light, as viewing the TV in poor light or during long period of time, strains your eyes.

• When using headphones, adjust the volume so as to avoid excessive levels, as hearing damage may result.

LCD Screen

• Although the LCD screen is made with high-precision technology and 99.99% or more of the pixels are effective, black dots may appear or bright points of light (red, blue, or green) may appear constantly on the LCD screen. This is a structural property of the LCD screen and is not a malfunction.

• Do not push or scratch the front filter, or place objects on top of this TV set. The image may be uneven or the LCD screen may be damaged.

• If this TV set is used in a cold place, a smear may occur in the picture or the picture may become dark. This does not indicate a failure. These phenomena disappear as the temperature rises.

• Ghosting may occur when still pictures are displayed continuously. It may disappear after a few moments.

• The screen and cabinet get warm when this TV set is in use. This is not a malfunction.

• The LCD screen contains a small amount of liquid crystal. Some fluorescent tubes used in this TV set also contain mercury. Follow your local ordinances and regulations for disposal.

Handling and cleaning the screen surface/cabinet of the TV set

Be sure to unplug the mains lead connected to the TV set from mains socket before cleaning. To avoid material degradation or screen coating degradation, observe the following precautions.

• To remove dust from the screen surface/cabinet, wipe gently with a soft cloth. If dust is persistent, wipe with a soft cloth slightly moistened with a diluted mild detergent solution.

• Never use any type of abrasive pad, alkaline/acid cleaner, scouring powder, or volatile solvent, such as alcohol, benzene, thinner or insecticide. Using such materials or maintaining prolonged contact with rubber or vinyl materials may result in damage to the screen surface and cabinet material.

• Periodic vacuuming of the ventilation openings is recommended to ensure to proper ventilation.

• When adjusting the angle of the TV set, move it slowly so as to prevent the TV set from moving or slipping off from its table stand.

Disposal of the TV set

Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems)

This symbol on the product or on its

packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

Disposal of waste ba tteries (applicable

in the European Union and other

European countries with separate

collection systems)

This symbol on the battery or on the

packaging indicates that the batter y provided

with this product shall not be treated as household waste. On certain batteries this symbol might be used in combinationwith a chemical symbol. The chemical symbols for mercury (Hg) or lead (Pb) are added if the battery contains more than 0.0005% mercury or 0.004% lead. By ensuring these batteries are disposed of correctly, you will help prevent potentially negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of the battery. The recycling of the materials will help to conserve natural resources. In case of products that for safety, performance or data integrity reasons require a permanent connection with a n incorporated battery, this battery should be replaced by qualified service staff only. To ensure that the battery will be treated properly, hand over the product at end-of-life to the applicable collection point for the recycling of electrical and electronic equipment. For all other batteries, please view the section on how to remove the battery from the product safely. Hand the battery over to the applicable collection point for the recycling of waste batteries. For more detailed information about recycling of this product or battery, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

Optional Equipment

Keep optional components or any equipment emitting electromagnetic radiation away from the TV set. Otherwise picture distortion and/or noisy sound may occur.

Overview of the remote

1 "/1 – TV standby

Turns the TV on and off from standby mode.

PROG

AUDIOSCENE

TOOLS

2 AUDIO

Press to change the dual sound mode (page 25).

3 SCENE – Scene Select (page 15) 4 Coloured buttons (page 15, 17) 5 / – Info/Text reveal

• In digital mode: Displays brief details of the programme currently being watched.

• In analogue mode: Displays information such as current channel number and screen format.

• In Text mode (page 15): Reveals hidden information (e.g. answers to a quiz).

6 F/f/G/g/ 7 TOOLS (page 15, 21)

Enables you to access various viewing options and change/make adjustments according to the source and screen format.

8 MENU (page 23) 9 Number buttons

• In TV mode: Selects channels. For channel numbers 10 and above, press the second and third digit in quick succession.

• In Text mode: Enters the three digit page number to select the page.

0 – Digital Favourite list

Press to display the Digital Favourite list that you have specified (page 17).

qa – Previous channel

Returns to the previous channel watched.

qs PROG +/-/ /

• In TV mode: Selects the next (+) or previous (-) channel.

• In Text mode (page 15): Selects the next ( ) or previous ( ) page.

qd 2 +/- – Volume qf % – Mute the sound qg / – Text (page 15) qh RETURN /

Returns to the previous screen of any displayed menu.

qj GUIDE / – EPG (Digital Electronic Programme Guide) (page 16) qk ANALOG – Analogue mode (page 14) ql DIGITAL – Digital mode (page 14) w; – Screen mode (page 15) wa – Input select

Selects the input source from equipment connected to the TV sockets (page 20).

• The number 5, PROG + and AUDIO buttons have tactile dots. Use the tactile dots as references when operating the TV.

ANALOGDIGITAL

GUIDE

RETURN

Overview of the TV buttons and indicators

1 1 – Power

Turns the TV on or off.

PROG

• To disconnect the TV completely, pull the plug from the mains.

• When you turn on the TV, the power indicator lights in green.

2 PROG +/-/ /

• In TV mode: Selects the next (+) or previous (-) channel.

• In TV menu: Moves through the options up ( ) or down ( ).

3 2 +/-/ /

• In TV mode: Increases (+) or decreases (-) the volume.

• In TV menu: Moves through the options right ( ) or left ( ).

4 / – Input select / OK

• In TV mode: Selects the input source from equipment connected to the TV sockets (page 20).

• In TV menu: Selects the menu or option, and confirms the setting.

5 (page 23) 6 Remote control sensor

• Receives IR signals from the remote.

• Do not put anything over the sensor, as its function may be affected.

7 – Picture Off / Sleep Timer indicator

• Lights up in green when the picture is switched off (page 26).

• Lights up in orange when the sleep timer is set (page 26).

8 1 – Standby indicator

Lights up in red when the TV is in standby mode.

9 " – Power indicator

Lights up in green when the TV is turned on.

• Make sure that the TV is completely turned off before unplugging the mains lead. Unplugging the mains lead while the TV is turned on may cause the indicator to remain lit or may cause the TV to malfunction.

Watching TV

ANALOGDIGITAL

GUIDE

1 Press 1 on the side of the TV to turn on

the TV.

When the TV is in standby mode (the 1 (standby) indicator on the TV front panel is red), press "/1 on the remote to turn on the TV.

2 Press DIGITAL to switch to digital mode,

or ANALOG to switch to analogue mode.

The channels available vary depending on the mode.

3 Press the number buttons or PROG +/- to

select a TV channel.

To select channel numbers 10 and above using the number buttons, press the second and third digits in quick succession. To select a digital channel using the Digital Electronic Programme Guide (EPG), see

AUDIOSCENE

page 16.

In digital mode

An information banner appears briefly. The following icons may be indicated on the banner.

RETURN

PROG

TOOLS

: Interactive service is available (MHEG

Digital Text)

: Interactive service (MHEG Digital Text) is

currently disabled

: Radio service

: Scrambled/Subscription service

: Multiple audio languages available

: Subtitles available

: Subtitles available for the hearing impaired

: Recommended minimum age for current

programme (from 4 to 18 years)

: Parental Lock

Additional operations

To Do this

Adjust the volume Press 2 + (increase)/

- (decrease).

Access the Programme index table (in analogue mode only)

Access the Digital Favourites (in digital mode only)

Press . To select an analogue channel, press F/f, then press

Press . For details, see page 17.

+ 30 hidden pages