Sony 145890811 User Manual

Installation Manual

Information of FCC ID Label of this device:
FCC ID: AK8145890811

For OEM integration only – device cannot be sold to general public.
Therefore we will ask OEM to include the following statements required
by FCC on the product and in the Installation manual Notice.

Contents

1.Land Pattern (Recommended)

2.Supply Voltage

3.Antenna

4.Notice

**This module can only be installed in host powered by battery.

0.125

0.325

0.575

0.775

1.025

1.225

1.475

1.675

1.925

2.125

2.375

2.575

2.825

3.15

3.65

3.95

0.10

0.35

0.55

0.80

1.00

1.25

1.45

1.70

1.90

2.15

2.35

2.60

2.80

3.05

3.25

3.50

3.85

0.60

1.30

2.50

3.15

3.65

3.95

0.60

1.30

2.50

3.05

3.55

3.85

1.Land Pattern TOP View (Recommended)

Please take a solid ground this shaded area.
In the surface layer, in the inner layer,
there is no problem either.

Unit : mm

2.Supply Voltage

min.

typ.

max.

unit

Operating Temperature

-20

+25

+85

deg.C

Supply
Voltage

VBAT

3.13

3.2

4.4

V

VDDXO*

1.70

1.8

1.9

V

VIO *

1.71

1.8 or 3.3

3.63
V

*VDDXO and VIO don’t influence the RF characteristic.

This module can only be installed in host powered by battery.

3.Antenna

■Please perform the antenna design that followed the specifications of the antenna.

■About the signal line between an antenna and a module

It is a 50-ohm line design.
Fine tuning of return loss etc. can be performed using a matching network.
However, it is required to check "Class1 change" and "Class2 change"
which the authorities define then.

The concrete contents of a check are the following three points.

１）It is the same type as the antenna type of antenna specifications.
２）An antenna gain is lower than a gain given in antenna specifications.

３）The emission level is not getting worse.

3.

Antenna

3.

Antenna(Trace design)

3.Antenna

(Trace design)

3.

Antenna(Trace design)

4. Notice

Please describe the following warning on the final product which contains this module.

Contains Transmitter

Contains FCC ID:

This device complies with Part 15 of FCC Rules and Industry Canada’s licence-exempt
to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.

Le

présent appareil est conforme à la partie 15 des règles de la FCC et aux normes des CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1)
l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.

※When the product is small, as for these words mentioned above, the posting to a manual is possible.

Module FCC ID:AK8145890811

or

AK8145890811

RSSs. Operation is subject

●Please describe the following warning to the manual.

FCC CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

4. Notice

●Please describe the following statement to the manual.

4. Notice

When installing it in a mobile equipment. Please describe the following warning to the manual.

●

If mobile equipment use only low power BT/BLE or low power Wi-Fi.

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency
(RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that
it deemed to comply without maximum permissive exposure evaluation (MPE). When installing this module in host with multiple or additional
transmitters, additional RF exposure evaluation is required.

Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les
règles les radioélectriques (RF) de la FCC lignes directrices d'exposition et d’exposition aux fréquences radioélectriques (RF) CNR-102
de l’IC. Cet équipement émet une énergie RF très faible qui est considérée conforme sans évaluation de l’exposition maximale
autorisée (MPE). Lors de l'installation de ce module sur un hôte avec plusieurs émetteurs ou plus, une évaluation d'exposition RF
supplémentaire est requise.

In the case of conditions other than the above

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and
RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s
body. When installing this module in host with multiple or additional transmitters, additional RF exposure evaluation is required.

Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles les radioélectriques (RF) de la FCC
lignes directrices d'exposition et d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement doit être installé et utilisé en gardant une distance de 20 cm
ou plus entre le radiateur et le corps humain. Lors de l'installation de ce module sur un hôte avec plusieurs émetteurs ou plus, une évaluation d'exposition RF supplémentaire est
requise.

Note)
Portable equipment : Equipment for which the spaces between human body and antenna are used within 20cm.
Mobile equipment : Equipment used at position in which the spaces between human body and antenna exceeded 20cm.

4. Notice