SONIQ CWR300ND-AU Instruction Manual

CWR300ND-AU

300M ADSL2+Wireless Router

CWR300ND

User Manual

- 1 -

Contents

1 Introduction ....................................................................................................- 3 -

1.1 Packing List .......................................................................................- 3 -

1.2 Safety Precautions ............................................................................- 3 -

1.3 LEDs and Interfaces..........................................................................- 4 -

1.4 System Requirements .......................................................................- 6 -

1.5 Features ............................................................................................- 7 -

2 Hardware Installation .....................................................................................- 8 -

3 Web Configuration .......................................................................................- 11 -

3.1 Access the Router ...........................................................................- 11 -

3.2 Wizard .............................................................................................- 12 -

3.3 Status...............................................................................................- 29 -

3.3.1 System..................................................................................- 29 -

3.3.2 LAN.......................................................................................- 30 -

3.3.3 WLAN ...................................................................................- 30 -

3.3.4 WAN .....................................................................................- 31 -

3.3.5 Port Mapping ........................................................................- 32 -

3.3.6 Statistics................................................................................- 32 -

3.3.7 ARP Table.............................................................................- 34 -

3.4 Network ...........................................................................................- 35 -

3.4.1 LAN.......................................................................................- 35 -

3.4.2 WAN .....................................................................................- 42 -

3.4.3 WLAN ...................................................................................- 48 -

3.5 Service.............................................................................................- 60 -

3.5.1 DNS ......................................................................................- 60 -

3.5.2 Firewall .................................................................................- 62 -

3.5.3 UPNP....................................................................................- 72 -

3.5.4 IGMP Proxy ..........................................................................- 72 -

3.5.5 TR-069..................................................................................- 73 -

3.5.6 ACL.......................................................................................- 75 -

3.6 Advance...........................................................................................- 78 -

3.6.1 Bridge Setting .......................................................................- 78 -

3.6.2 Routing .................................................................................- 80 -

- 2 -

3.6.3 Port Mapping ........................................................................- 83 -

3.6.4 QoS.......................................................................................- 85 -

3.6.5 SNMP ...................................................................................- 88 -

3.6.6 Others ...................................................................................- 89 -

3.7 Admin ..............................................................................................- 89 -

3.7.1 Commit/Reboot.....................................................................- 89 -

3.7.2 Upgrade ................................................................................- 90 -

3.7.3 System Log...........................................................................- 91 -

3.7.4 Password ..............................................................................- 92 -

3.7.5 Time Zone.............................................................................- 94 -

3.7.6 Logout...................................................................................- 95 -

3.8 Diagnostic........................................................................................- 95 -

3.8.1 Ping.......................................................................................- 95 -

3.8.2 ATM Loopback ......................................................................- 96 -

3.8.3 ADSL ....................................................................................- 97 -

3.8.4 Diagnostic Test .....................................................................- 97 -

- 3 -

1 Introduction

The CWR300ND is an ADSL access device that supports multiple line modes. It

provides one 10/100Base-T Ethernet interface at the user end. The device

provides high-speed ADSL broadband connection to the Internet or Intranet for

high-end users, such as net cafes and office users. The device provides high

performance access to the Internet, downlink up to 24 Mbps and uplink up to 1

Mbps.

The device supports WLAN access. It can connect to the Internet through a WLAN

AP or WLAN device. It complies with IEEE 802.11, 802.11b/g/n specifications, WEP,

WPA, and WPA2 security specifications.

1.1 Packing List

 1 x CWR300ND

 1 x external splitter

 1 x power adapter

 2 x telephone cables (RJ11)

 1 x Ethernet cable (RJ45)

 1 x CD

 1 x WARRANTY CARD

1.2 Safety Precautions

Follow the following instructions to prevent the device from risks and damage

caused by fire or electric power:

 Use volume labels to mark the type of power.

 Use the power adapter packed within the device package.

 Pay attention to the power load of the outlet or prolonged lines. An

overburden power outlet or damaged lines and plugs may cause electric

shock or fire accident. Check the power cords regularly. If you find any

damage, replace it at once.

- 4 -

 Proper space left for heat dissipation is necessary to avoid damage caused

by overheating to the device. The long and thin holes on the device are

designed for heat dissipation to ensure that the device works normally. Do

not cover these heat dissipation holes.

 Do not put this device close to a place where a heat source exists or high

temperature occurs. Avoid the device from direct sunshine.

 Do not put this device close to a place where it is over damp or watery. Do

not spill any fluid on this device.

 Do not connect this device to any PCs or electronic products, unless our

customer engineer or your broadband provider instructs you to do this,

because any wrong connection may cause power or fire risk.

 Do not place this device on an unstable surface or support.

1.3 LEDs and Interfaces

Front Panel

The following table describes the LEDs of the device:

LED Color Status Description

On The device is powered on and the

initialization is normal.

Green

Off The power is off.

Power

Red On The device is self-testing or self-testing is

failed.

Slow

Blinks

No signal is detected.

Fast

Blinks

The device is handshaking with the physical

layer of the office.

ADSL Green

On The device is connected to the physical layer

of the office.

- 5 -

LED Color Status Description

On The Internet connection is normal in the

routing mode (for example: PPP dial-up is

successful), and no Internet data is being

transmitted.

Blinks Internet data is being transmitted in the

routing mode.

Green

Off The device is in bridged mode.

Internet

Red On The Internet connection fails after successful

synchronization in the routing mode (for

example: PPP dial-up is failed).

On The LAN connection is normal.

Blinks Data is being transmitted through the LAN

interface, or the Internet data is being

transmitted in bridged mode.

LAN4-1 Green

Off The LAN connection is not established.

On The WLAN connection has been activated.

Blinks Data is being transmitted through the WLAN

interface.

WLAN Green

Off The WLAN connection is not activated.

Blinks WPS is activated and the device is waiting

for negotiation with the clients.

WPS Green

Off WPS is not activated.

Rear Panel

- 6 -

The following table describes the interfaces of the device:

Interface/Button Description

WPS/WLAN

 Press the button silently less than 1s to enable

WLAN function.

 Press the button for more than 5s to enable WPS

function.

If you press the button between 1s and 5s, no function

takes effect.

ADSL

RJ-11 interface, for connecting to the ADSL interface or

a splitter through a telephone cable.

LAN4/3/2/1

RJ-45 interface, for connecting to the Ethernet interface

of a PC or the Ethernet device through an Ethernet

cable.

Power

Power interface for connecting to the power adapter of

12 V DC ,1A.

Power switch, power on or off the device.

Reset

Reset to the factory defaults. To restore factory defaults,

keep the device powered on and insert a needle into the

hole for 3 to 6 seconds and then release.The device is

reset to the factory default configuration.

1.4 System Requirements

Recommended system requirements are as follows:

 A 10/100 base-T Ethernet card is installed on your PC

 A hub or Switch. (connected to several PCs through one of Ethernet

interfaces on the device)

 Operating system: Windows 98SE, Windows 2000, Windows ME, Windows

XP

 Internet Explorer V5.0 or higher, Netscape V4.0 or higher, or Firefox 1.5 or

higher

- 7 -

1.5 Features

The device supports the following features:

 Various line modes

 External PPPoE dial-up access

 Internal PPPoE/PPPoA dial-up access

 1483Briged/1483Routed/MER/IPoA access

 Multiple PVCs (up to eight) and these PVCs can be isolated from each other

 A single PVC with multiple sessions

 Multiple PVCs with multiple sessions

 802.1Q and 802.1P protocol

 DHCP server

 NAPT

 Static route

 Firmware upgrading through Web, TFTP, or FTP

 Resetting to the factory defaults through Reset button or Web

 DNS

 Virtual server

 DMZ

 Two-level passwords and usernames

 Web interface

 Telnet CLI

 System status display

 PPP session PAP/CHAP

 IP filter

 IP quality of service (QoS)

 Remote access control

 Line connection status test

 Remote managing through Telnet or HTTP

 Backup and restoration of configuration file

 Ethernet interface supporting crossover detection, auto-correction, and

polarity correction

 Universal plug and play (UPnP)

- 8 -

2 Hardware Installation

Step 1 Connect the ADSL interface of the device and the Modem interface of

the splitter through a telephone cable. Connect the phone to the Phone

interface of the splitter through a cable. Connect the incoming line to the

Line interface of the splitter.

The splitter has three interfaces:

 Line: Connect to a wall phone jack (RJ-11 jack).

 Modem: Connect to the ADSL jack of the device.

 Phone: Connect to a telephone set.

Step 2 Connect the LAN interface of the device to the network card of the PC

through an Ethernet cable (MDI/MDIX).

Note:

Use twisted-pair cables to connect with the hub or switch.

Step 3 Plug one end of the power adapter to the wall outlet and connect the

other end to the Power interface of the device.

Connection 1

Figure 1 shows the application diagram for the connection of the router, PC, splitter

and the telephone sets, when no telephone set is placed before the splitter.

- 9 -

Figure 1 Connection diagram (Without connecting telephone sets before the splitter)

Connection 2

Figure 2 shows the connection when the splitter is installed close to the router.

Figure 2 Connection diagram (Connecting a telephone set before the splitter)

- 10 -

Note:

When connection 2 is used, the filter must be installed close to the telephone

cable. See Figure2. Do not use the splitter to replace the filter.

Installing a telephone directly before the splitter may lead to failure of connection

between the device and the central office, or failure of Internet access, or slow

connection speed. If you really need to add a telephone set before the splitter, you

must add a microfilter before a telephone set. Do not connect several telephones

before the splitter or connect several telephones with the microfilter.

- 11 -

3 Web Configuration

This chapter describes how to configure the router by using the Web-based

configuration utility.

3.1 Access the Router

The following is the detailed description of accesing the router for the first time.

Step 1 Open the Internet Explorer (IE) browser and enter http://192.168.1.1

.

Step 2 In the Login page that is displayed, enter the username and password.

 The username and password of the super user are admin and admin.

 The username and password of the common user are user and user.

If you log in as a super user, the page shown in the following figure appears. You

can check, configure and modify all the settings.

- 12 -

When you log in as a common user, you can check the status of the router, but can

not configure the most of the settings.

Note:

In the Web configuration page, you can click Apply Changes to save the

settings temporarily. If you want to save the settings of this page permanently,

click Save of Attention that appears at the bottom of the Web page after the

configuration.

3.2 Wizard

When subscribing to a broadband service, you should be aware of the method by

which you are connected to the Internet. Your physical WAN device can be either

PPP, ADSL, or both. The technical information about the properties of your Internet

connection is provided by your Internet Service Provider (ISP). For example, your

ISP should inform you whether you are connected to the Internet using a static or

dynamic IP address, and the protocol that you use to communicate on the Internet.

The Wizard page guides fast and accurate configuration of the Internet connection

and other important parameters. The following sections describe these various

configuration parameters. Whether you configure these parameters or use the

default ones, click NEXT to enable your Internet connection.

- 13 -

In the navigation bar, choose Wizard. The page shown in the following figure

appears.

You may change the password by entering a new one, or enter the current

password and then click NEXT. The page shown in the following figure appears. In

this page, you can set the system time and Network Time Protocol (NTP) server.

- 14 -

The following table describes the parameters of this page:

Field

Description

State

You can disable or enable NTP function. You have to

enable it if you want to configure the parameters in this

page.

Server IP Enter the IP address of the specified time server manually.

Interval

Set the interval that the router obtains the time from the

time server and verifies it with the server.

Time Zone Choose the time zone of your country.

GMT time It displays the Greenwich mean time.

After finishing the configuration, click NEXT. The page shown in the following figure

appears.

- 15 -

The following table describes the parameters of this page:

Field

Description

Country Select the Country from the drop-down list.

ISP

Select the ISP according to the country from the

drop-down list. If you do not find the ISP that matches

the country, you can select Others.

Protocol

Select the WAN connection type. You can select from

the drop-down list.

Connection

Type

You can select LLC or VC-Mux.

VPI/VCI

 VPI:Virtual path between two points in an ATM

network. Its valid value range is from 0 to 255.

 VCI: The virtual channel between two points in an

ATM network, ranging from 32 to 65535 (0 to 31 is

reserved for local management of ATM traffic).

User name The correct user name that your ISP provides to you.

Password The correct password that your ISP provides to you.

After finishing the configuration, click NEXT. The page shown in the following figure

appears.

- 16 -

The following table describes the parameters of this page:

Field

Description

WLAN

Interface

You can choose Enable or Disable. By default, WAN

interface is enabled.

You need to enable WAN interface, and then you can

set the parameters in this page.

Band

Choose the working mode of the router. You can choose

24 GHz(B), 24 GHz(G), 24 GHz(B+G), 24 GHz(N), 24

GHz(G+N) or 24 GHz(B+G+N).

SSID

The service set identification (SSID) is a unique name to

identify the router in the wireless LAN. Wireless stations

associating to the router must have the same SSID.

Enter a descriptive name that is used when the wireless

client connecting to the router.

Encryption

Configure the wireless encryption mode. You can

choose None, WEP, WPA (TKIP), WPA (AES), WPA2

(AES), WPA2 (TKIP) or WPA2 Mixed.

 Wired equivalent privacy (WEP) encrypts data

- 17 -

Field

Description

frames before transmitting over the wireless

network.

 Wi-Fi protected access (WPA) is a subset of the

IEEE802.11i security specification draft.

 WPA2 Mixed is the collection of WPA and WPA2

encryption modes. The wireless client establishes

the connection between the router through WPA or

WPA2.

Key differences between WPA and WEP are user

authentication and improved data encryption.

After finishing the configuration, click NEXT. The page shown in the following figure

appears.

- 18 -

Note:

If the WAN connection type is set to PPPoA, the parameters of the WAN

connection type are the same as those of PPPoE. For the parameters in these

pages, refer to the parameter description of PPPoE.

1483 Bridged

In the WAN Interface Setup page, set the WAN connection type to 1483 Bridged.

The page shown in the following figure appears.

Click NEXT. The page shown in the following figure appears.

- 19 -

The following table describes the parameters of this page:

Field

Description

WLAN

Interface

You can choose Enable or Disable. By default, WAN

interface is enabled.

You need to enable WAN interface, and then you can

set the parameters in this page.

Band

Choose the working mode of the router. You can choose

24 GHz(B), 24 GHz(G), 24 GHz(B+G), 24 GHz(N), 24

GHz(G+N) or 24 GHz(B+G+N).

SSID

The service set identification (SSID) is a unique name to

identify the router in the wireless LAN. Wireless stations

associating to the router must have the same SSID.

Enter a descriptive name that is used when the wireless

client connecting to the router.

Encryption

Configure the wireless encryption mode. You can

choose None, WEP, WPA (TKIP), WPA (AES), WPA2

(AES), WPA2 (TKIP), or WPA2 Mixed.

 Wired equivalent privacy (WEP) encrypts data

- 20 -

Field

Description

frames before transmitting over the wireless

network.

 Wi-Fi protected access (WPA) is a subset of the

IEEE802.11i security specification draft.

 WPA2 Mixed is the collection of WPA and WPA2

encryption modes. The wireless client establishes

the connection between the router through WPA or

WPA2.

Key differences between WPA and WEP are user

authentication and improved data encryption.

After finishing the configuration, click NEXT. The page shown in the following figure

appears.

1483 MER: DHCP

In the WAN Interface Setup page, set the WAN connection type to be 1483 MER:

DHCP. The page shown in the following figure appears.

- 21 -

The following table describes the parameters of this page:

Field Description

Country Select the Country from the drop-down list.

ISP

Select the ISP according to the country from the

drop-down list. If you do not find the ISP that matches

the country, you can select Others

Protocol

Select the WAN connection type. You can select from

the drop-down list.

- 22 -

Connection

Type

You can select LLC or VC-Mux.

VPI/VCI

 VPI: Virtual path between two points in an ATM

network. Its valid value range is from 0 to 255.

 VCI: The virtual channel between two points in an

ATM network, ranging from 32 to 65535 (0 to 31 is

reserved for local management of ATM traffic).

Click NEXT, the page shown in the following figure appears.

The following table describes the parameters of this page:

- 23 -

Field

Description

WLAN

Interface

You can choose Enable or Disable. By default, WAN

interface is enabled.

You need to enable WAN interface, and then you can

set the parameters in this page.

Band

Choose the working mode of the router. You can choose

24 GHz(B), 24 GHz(G), 24 GHz(B+G), 24 GHz(N), 24

GHz(G+N) or 24 GHz(B+G+N).

SSID

The service set identification (SSID) is a unique name to

identify the router in the wireless LAN. Wireless stations

associating to the router must have the same SSID.

Enter a descriptive name that is used when the wireless

client connecting to the router.

Encryption

Configure the wireless encryption mode. You can

choose None, WEP, WPA (TKIP), WPA (AES), WPA2

(AES), WPA2 (TKIP), or WPA2 Mixed.

 Wired equivalent privacy (WEP) encrypts data

frames before transmitting over the wireless

network.

 Wi-Fi protected access (WPA) is a subset of the

IEEE802.11i security specification draft.

 WPA2 Mixed is the collection of WPA and WPA2

encryption modes. The wireless client establishes

the connection between the router through WPA or

WPA2.

Key differences between WPA and WEP are user

authentication and improved data encryption.

After finishing the configuration, click NEXT. The page shown in the following figure

appears.

- 24 -

1483 Routed/1483 MER: Static IP

- 25 -

The following table describes the parameters of this page:

Field Description

Country Select the Country from the drop-down list.

ISP

Select the ISP according to the country from the

drop-down list. If you do not find the ISP that matches

the country, you can select Others

Protocol

Select the WAN connection type. You can select from

the drop-down list.

- 26 -

Connection

Type

You can select LLC or VC-Mux.

VPI/VCI

 VPI: Virtual path between two points in an ATM

network. Its valid value range is from 0 to 255.

 VCI: The virtual channel between two points in an

ATM network, ranging from 32 to 65535 (0 to 31 is

reserved for local management of ATM traffic).

WAN IP

Address

Enter the IP address of the WAN interface provided by

your ISP.

Subnet Mask

Enter the subnet mask concerned to the IP address of

the WAN interface provided by your ISP.

Default

Gateway

Enter the default gateway of the WAN interface provided

by your ISP.

Primary DNS

Server

Enter the primary DNS server of the WAN interface

provided by your ISP.

Click NEXT, the following page appears.

- 27 -

The following table describes the parameters of this page:

Field

Description

WLAN

Interface

You can choose Enable or Disable. By default, WAN

interface is enabled.

You need to enable WAN interface, and then you can

set the parameters in this page.

Band

Choose the working mode of the router. You can choose

24 GHz(B), 24 GHz(G), 24 GHz(B+G), 24 GHz(N), 24

GHz(G+N) or 24 GHz(B+G+N).

SSID

The service set identification (SSID) is a unique name to

identify the router in the wireless LAN. Wireless stations

associating to the router must have the same SSID.

Enter a descriptive name that is used when the wireless

client connecting to the router.

Encryption

Configure the wireless encryption mode. You can

choose None, WEP, WPA (TKIP), WPA (AES), WPA2

(AES), WPA2 (TKIP), or WPA2 Mixed.

 Wired equivalent privacy (WEP) encrypts data

frames before transmitting over the wireless

- 28 -

Field

Description

network.

 Wi-Fi protected access (WPA) is a subset of the

IEEE802.11i security specification draft.

 WPA2 Mixed is the collection of WPA and WPA2

encryption modes. The wireless client establishes

the connection between the router through WPA or

WPA2.

Key differences between WPA and WEP are user

authentication and improved data encryption.

After finishing the configuration, click NEXT. The page shown in the following figure

appears.