Sonifex S2, SOL-MB1300, SOL-MB1500, SOL-SB1600, SOL-T12 User Handbook Manual

S2 Solutions Furniture

User Handbook

b

S2 Solutions Furniture User Handbook

This handbook is for use with the following product:
S2 Solutions Furniture

©Sonifex Ltd, 2006
All Rights Reserved
Revision 1.00, June 2006

Sonifex Ltd, 61, Station Road, Irthlingborough,
Northants, NN9 5QE, England.
Tel: [phone]
Fax: [phone]
Email: [e-mail]
Website: http://www.sonifex.co.uk

Information in this document is subject to change without notice and does not represent a commitment on the part of the
vendor. Sonifex Ltd shall not be liable for any loss or damage whatsoever arising from the use of information or any error
contained in this manual.

No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including
photocopying, recording, information storage and retrieval systems, for any purpose other than the purchaser’s personal
use, without the express written permission of Sonifex Ltd. Unless otherwise noted, all names of companies, products
and persons contained herein are part of a completely fictitious adaptation and are designed solely to document the use of
Sonifex product.

S2 SOLUTIONS FURNITURE
USER HANDBOOK

S2 SOLUT ION S F URN ITU RE USE R H AND BOO K

S2 Solutions Furniture User Handbook

c

CONT E NTS

CONTENTS

Warranty i

Warranty and Liability i
Unpacking the S2 Solutions i

i

Warranty Registration i

i

Safety Information iii

Safety Equipment iii
Material Handling ii

i

Atmosphere ii

i

WEEE & RoHS Directives - Sonifex Statement ii

i

1 Introduction 1

Room Requirements 1
Manpower and Tools Needed

1

2 S2 Solutions Single Mixer Furniture Installation 3

Main Components 3
Fitting the Main SOL-MB1300 or SOL-MB1500 Mixer Desk Top to the SOL-SB1600 Side
Work-Surface

4

Adjusting the Height of the Furniture

6

Fitting the SOL-D8, or SOL-D12 Desk Top 19” Rack

6

Fitting the Optional SOL-T12 Top 19” Rack

6

Fitting the SOL-CVR80 Desk End Cover Panel

7

Assembling U-Shaped S2 Solutions Single Mixer Furniture

7

S2 Solutions Single Mixer Furniture Full Assembly

8

3 S2 Solutions Split Mixer Furniture Installation 9

Main Components 9
Assembly of the SOL-MBR, SOL-MBL and the SOL-MBC Mixer Work-Surfaces 1

0

Fitting the SOL-SB1000 Side Work-Surfaces 1

0

Fitting the SOL-D8, or SOL-D12 Desk Top 19” Rack 1

2

Fitting the Optional SOL-T12 Top 19” Rack 1

2

S2 Solutions Split Mixer Furniture Full Assembly 1

4

d

S2 Solutions Furniture User Handbook

FIGURES

FIG URE S

Figures

Fig 1: S2 Solutions Single Mixer L Shaped Furniture, Viewed From Above 3

Fig 2a: SOL-MB1300 or SOL-MB1500 and SOL-SB1600 assembly

5

Fig 2b: SOL-B12 support base 19” rack attachment

5

Fig 3: Detail of adjustable feet on SOL-B12 support base 19” rack and the SOL-LGG80

6

Fig 4: Fitting the Optional SOL-T12 Top 19” rack

7

Fig 5: S2 Solutions Single Mixer Furniture Full Assembly (Dims in mm)

8

Fig 6: S2 Solutions Split Mixer Furniture, Viewed From Above

9

Fig 7: S2 Solutions Split Mixer Work Surface Assembly 1

0

Fig 8: Fitting SOL-LGG80 Legs to the SOL-SB1000 side return 1

1

Fig 9: Assembling The SOL-SB1000 Side Return And SOL-B12 12U Support Base 19” Rack 1

2

Fig 10: Fitting the Optional SOL-T12 Top 19” rack 1

3

Fig 11: S2 Solutions Split Mixer Furniture Full Assembly (Dims in mm) 1

4

S2 Solutions Furniture User Handbook

i

Warranty

Warranty and Liability

Important: the purchaser is advised to read this clause

(a) The Company agrees to repair or (at its discretion) replace Goods which are found to

be defective (fair wear and tear excepted) and which are returned to the Company
within 12 months of the date of despatch provided that each of the following
are satisfied:

(i) notification of any defect is given to the Company immediately upon its

becoming apparent to the Purchaser;

(ii) the Goods have only been operated under normal operating conditions and

have only been subject to normal use (and in particular the Goods must have
been correctly connected and must not have been subject to high voltage or
to ionising radiation and must not have been used contrary to the Company’s
technical recommendations);

(iii) the Goods are returned to the Company’s premises at the Purchaser’s expense;

(iv) any Goods or parts of Goods replaced shall become the property of

the Company;

(v) no work whatsoever (other than normal and proper maintenance) has been

carried out to the Goods or any part of the Goods without the Company’s prior
written consent;

(vi) the defect has not arisen from a design made, furnished or specified by

the Purchaser;

(vii) the Goods have been assembled or incorporated into other goods only in

accordance with any instructions issued by the Company;

(viii) the defect has not arisen from a design modified by the Purchaser;

(ix) the defect has not arisen from an item manufactured by a person other than

the Company.

In respect of any item manufactured by a person other than the Company, the Purchaser
shall only be entitled to the benefit of any warranty or guarantee provided by such
manufacturer to the Company.

(b) In respect of computer software supplied by the Company the Company does not

warrant that the use of the software will be uninterrupted or error free.

(c) The Company accepts liability:

(i) for death or personal injury to the extent that it results from the negligence of

the Company, its employees (whilst in the course of their employment) or its
agents (in the course of the agency);

WARRANTY

WAR R AN TY

ii

S2 Solutions Furniture User Handbook

(ii) for any breach by the Company of any statutory undertaking as to title, quiet

possession and freedom from encumbrance.

(d) Subject to conditions (a) and (c) from the time of despatch of the Goods from the

Company’s premises the Purchaser shall be responsible for any defect in the Goods
or loss, damage, nuisance or interference whatsoever consequential economic or
otherwise or wastage of material resulting from or caused by or to the Goods. In
particular the Company shall not be liable for any loss of profits or other economic
losses. The Company accordingly excludes all liability for
the same.

(e) At the request and expense of the Purchaser the Company will test the Goods to

ascertain performance levels and provide a report of the results of that test. The
report will be accurate at the time of the test, to the best of the belief and knowledge
of the Company, and the Company accepts no liability in respect of its accuracy
beyond that set out in Condition (a).

(f) Subject to Condition (e) no representation, condition, warranty or other term, express

or implied (by statute or otherwise) is given by the Company that the Goods are of
any particular quality or standard or will enable the Purchaser to attain any particular
performance or result, or will be suitable for any particular purpose or use under
specific conditions or will provide any particular capacity, notwithstanding that the
requirement for such performance, result or capacity or that such particular purpose
or conditions may have been known (or ought to have been known) to the Company,
its employees or agents.

(g) (i) To the extent that the Company is held legally liable to the Purchaser for any

single breach of contract, tort, representation or other act or default, the
Company’s liability for the same shall not exceed the Price of the Goods.

(ii) The restriction of liability in Condition (g)(i) shall not apply to any liability

accepted by the Seller in Condition (c).

(h) Where the Goods are sold under a consumer transaction (as defined by the Consumer

Transactions (Restrictions on Statements) Order 1976) the statutory rights of the
Purchaser are not affected by these Conditions of Sale.

Unpacking the S2 Solutions

Each S2 Solutions is shipped in protective packaging and should be inspected for damage
before use. Where an item is found to have transit damage, notify the carrier immediately
with all the relevant details of the shipment. Packing materials should be kept for inspection
and also for if the product needs to be returned.

Warranty Registration

In order to register the date of purchase so that we can keep you informed of any design
improvements or modifications, it is important to complete the warranty registration
document that is enclosed and return it to Sonifex Ltd in the UK, or register online at
www.sonifex.co.uk/register

WARRANTY

WAR R AN TY

S2 Solutions Furniture User Handbook

iii

Safety Information

Safety Equipment

This equipment has been designed to meet the safety regulations currently advised
in the country of purchase and it conforms to the safety regulations specified by
use of the CE Mark.

Material Handling

The woodwork supplied is heavy and it can be difficult/strenuous for one person to
assemble it. Please use all safety precautions and follow your company Health & Safety
guidelines for assembling the furniture.

Atmosphere

The units should be installed in an area that is not subject to excessive temperature
variation (<0°C, >50°C), moisture, dust or vibration.

WEEE & RoHS Directives - Sonifex Statement

The Waste Electrical and Electronic Equipment (WEEE) Directive was agreed on
13 February 2003, along with the related Directive 2002/95/EC on Restrictions
of the use of certain Hazardous Substances in electrical and electronic
equipment (RoHS).

The Waste Electrical and Electronic Equipment Directive (WEEE) aims to minimise the
impacts of electrical and electronic equipment on the environment during their life times
and when they become waste. It applies to a huge spectrum of products. It encourages
and sets criteria for the collection, treatment, recycling and recovery of waste electrical and
electronic equipment. All products manufactured by Sonifex Ltd have the WEEE directive
label placed on the case. It gives a contact for individuals who are unsure about the correct
procedure when the product has reached its “end of use”.

Sonifex Ltd will be happy to give you information about local organisations that can
reprocess the products, or alternatively all products that have reached “end of use” can be
returned to Sonifex and will be reprocessed correctly free of charge.

Sonifex Ltd is in the process of phasing out the use of certain hazardous substances
identified in the European Union’s Restriction of Hazardous Substances (RoHS) directive.
The RoHS directive limits the use of certain hazardous substances currently used in EEE
manufacture, including lead, mercury, cadmium, hexavalent chromium, and halide­containing compounds PBB (polybrominated biphenyl) and PBDE (polybrominated
diphenyl ether). Elimination of these substances will result in more environmentally friendly
recycling of electronic equipment. For the products which Sonifex manufacture, the main
area where products were affected was in the use of lead for manufacturing and assembling
electronics circuit boards.

Sonifex Ltd practices lead-free (LF) manufacturing processes. LF solder is used on the
surface-mount PCB manufacturing processes and for hand soldering. The printed circuit

SAFETY INFORMATION

SAF ET Y I NFO RMATI O N

iv

S2 Solutions Furniture User Handbook

boards (PCBs) used are either gold plated, or immersion tin plated, both of which use no
lead. Historically the PCBs were hot air solder levelled (HASL) PCBs which used tin/lead
based solder.

The manufacturing processes include the assembly of purchased components from various
sources. Product is offered as RoHS compliant, or LF, only after sufficient evidence is received
from the component manufacturers that their components are RoHS compliant. Sonifex
Ltd relies solely on the distributor, or manufacturer, of the components for identification of
RoHS compliance. Thus whilst every effort is made to ensure compliance, Sonifex Ltd makes
no warranty, or certification, or declaration of compliance concerning said components.

Sonifex Ltd defines “Lead Free” as pertaining to any product, which has been manufactured
by Sonifex Ltd using components which have been declared by the manufacturers as
“Lead Free”. All statements by Sonifex Ltd of RoHS compliance are based on component
manufacturer documentation.

SAFETY INFORMATION

SAF ET Y I NFO RMATI O N

S2 Solutions Furniture User Handbook

1

INTRODUCTION

INT ROD UC TIO N

1

1 Introduction

The information provided here is for the assembly of the S2 Solutions furniture. For
information on the assembly of the mixer and other equipment please refer to the specific
equipment handbooks.

Section 2 covers the assembly of the S2 Solutions Single Mixer furniture (usually L-shaped,
but can be U-shaped).

Section 3 covers the S2 Solutions Split Mixer furniture assembly (usually U-shaped, but can
be L-shaped).

The studio furniture has been designed by Sonifex to offer a series of modular components
that create a flexible package that can be tailored to suit various room sizes and customer
requirements. Please read this document thoroughly before you start to install the furniture.

The Sonifex S2 Solutions can also be purchased as a fully featured, low price radio studio
package, which is complete in every detail. The packages are centred around the Sonifex S2
mixing console, set in custom technical furniture. With both guest and presenter positions,
the package is ideal for hospital radios, RSL’s, sports grounds, colleges and university
media studies departments.

The studio furniture is ergonomically designed to house all of the technical equipment and
place frequently used items within easy reach of the presenter. Manufactured in high quality
ash, the furniture modules can be arranged in either L or U shaped layouts and the L shaped
components can be installed either left-handed or right handed. The surfaces are covered
with hard wearing, blue/grey mottled linoleum surfaces which are not only robust but also
have good acoustic qualities - items dropped onto the surface produce a dull thud, to which
the microphone is not sensitive. The edges of the woodwork have a grey/black edging strip
with ash trim set back underneath the work-top.

Alternatively for applications where the requirements are different, full custom packages can
be accommodated. Please contact Sonifex Ltd for a competitive quote.

Room Requirements

The Solutions radio package was designed to compliment small studios and its’ compact
dimensions should allow installation in almost any room. It is worth noting that you will
need to allow additional room around the package for the presenter and guests to sit
comfortably.

You should fully consider the acoustics of your proposed room. Sound isolation from the
world outside is essential if you wish to produce quality radio programmes. Ideally, the walls
should be covered in a non acoustically reflective surface.

Manpower and Tools Needed

The furniture can be unpacked and initially assembled by one person, but there will be
times when two people need to be present to erect or move the furniture. Please adhere to
your company Health and Safety guidelines when lifting heavy weights.

2

S2 Solutions Furniture User Handbook

INTRODUCTION

INT ROD UC TIO N

1

Make sure that you have the following tools available to assemble the furniture :

• No.2 Pozi-drive screwdriver.

• A socket set with a 13mm driver.

• A 13mm open ended spanner.

• A medium length spirit level.

S2 Solutions Furniture User Handbook

3

2 S2 Solutions Single Mixer Furniture Installation

Your S2 Solutions package should arrive boxed or wrapped. Check the condition of the
boxes, packaging and woodwork and if any damage is evident report this to the carrier
before signing for the packages. Also report any damage immediately to Sonifex Ltd.

Each woodwork item is supplied with its relevant fixings. Make sure that you don’t throw the
fixings away in the packaging.

The Single Mixer Furniture is usually configured as an L-shape but can also be assembled as
a U shape if you’ve ordered an additional SOL-SB1600 Side return and SOL-LGG80 Table legs.

Main Components

SOL-MB1300 or SOL-MB1500 Mixer desktop that holds the S2 series mixers (either 1.3m
or 1.5m wide respectively).
SOL-SB1600 Side return with joint box.
SOL-T12 (Optional) 12U top 19” rack straight double on legs.
SOL-B12 12U support base 19” rack.
SOL-D8 or SOL-D12 Desk top 19” rack (either 8U or 12U high).
SOL-LGG80 80mm silver/grey round table legs (pair).
SOL-CVR80 Desk end cover panel.

The package can be installed with the side work-surface on either the right or left hand side
of the mixing console. So, your first decision will be to decide if you want the package to be
left or right handed. The instructions below assume left handed operation.

Fig 1 : S2 Solutions Single Mixer L Shaped Furniture, Viewed From Above.

Presenter’s seating
position

S2 mixe

r

cut-ou

t

SOL-SB1600
Side

return

work

surface

SOL-D8
Desk Top 19” rack

SOL-MB1300/MB1500
Mixer desk

top

work surface

SOL-CVR80
Desk end cover pane

l

SOL-CVR8

0

Desk end cover pane

l

2

S2 SOLUTIONS SINGLE MIXER

FURNITURE UNSTALLATION

S2 SOLUT ION S S ING LE MIX ER FUR NIT URE IN STAL L AT ION

4

S2 Solutions Furniture User Handbook

Fitting the Main SOL-MB1300 or SOL-MB1500 Mixer Desk Top to the
SOL-SB1600 Side Work-Surface

• Clear an area of the floor to make sure that it is clean and free from debris (so as not to
mark the desk linoleum surface).

• Place the SOL-SB1600 side work surface upside down on the floor, this is to aid the
correct alignment of the two parts.

• Orient either the SOL-MB1300 or SOL-MB1500 mixer desk top so that the cable access
in the side faces align with the cable access holes in the side faces of the SOL-SB1600
side work surface & place the side joint box in the gap between the two work surfaces
in line with the holes in the side return.

• The two parts are fixed together with two M8 x 140mm bolts, four large flat washers
and two M8 nuts supplied. These are inserted through holes in the SOL-SB1600 side
work surface, the joint box and the corresponding holes in the mixer desktop.

• Screw 2 x SOL-LGG80 silver/grey round table legs into the mounting plates fitted in
the SOL-SB1600 desk top and 2 table legs into the mounting plates in the mixer desk
top (as shown in fig.2a).

• Place the SOL-B12 support base 19” rack to the left or right of the presenter’s seat
position and slightly behind it.

• Turn the connected SOL-SB1600 side work surface and the SOL-MB1300 or SOL­MB1500 mixer desk top over and place it on top of the SOL-B12 support base 19” rack,
taking care not to put side load on the SOL-LGG80 round table legs (Note: This part
of the installation process needs at least two people to perform it safely). Move these
items by lifting the work surfaces, i.e. not by dragging along the floor.

• Move the SOL-B12 support base 19” rack into position underneath the work surfaces.

S2 SOLUT ION S S ING LE MIX ER FUR NIT URE IN STAL L AT ION

S2 SOLUTIONS SINGLE MIXER
FURNITURE UNSTALLATION

2

S2 Solutions Furniture User Handbook

5

Fig 2a : SOL-MB1300 or SOL-MB1500 and SOL-SB1600 assembly.

SOL-LGG80
Silver/grey table legs

SOL-CVR80
Desk end cover pane

l

SOL-MB1300/MB1500
Mixer desk

top

work

surface

SOL-SB1600
Side

return

work

surface

Joint bo

x

Bolt
positions

Fig 2b : SOL-B12 support base 19” rack attachment.

SOL-B12
Support Base 19” rack

2

S2 SOLUTIONS SINGLE MIXER

FURNITURE UNSTALLATION

S2 SOLUT ION S S ING LE MIX ER FUR NIT URE IN STAL L AT ION

6

S2 Solutions Furniture User Handbook

Adjusting the Height of the Furniture

Before installing the cables and equipment into the wood-work, adjust the height of the
package so that it is stable and level, using the spirit level. This is achieved by adjusting the
bases of the SOL-LGG80 round legs and the adjustable feet on the SOL-B12 support base
19” rack. After levelling the whole assembly check and fully tighten the M8 fixing bolts
in the desktops.

Fig 3 : Detail of adjustable feet on SOL-B12 support base 19” rack and the SOL-LGG80.

Fitting the SOL-D8, or SOL-D12 Desk Top 19” Rack

The SOL-D8 or SOL-D12 desktop 19” rack simply sits on the linoleum worktop of the
SOL-SB1600 side work surface. If you are fitting the free standing SOL-D8 or SOL-D12 desk
top 19” rack, you will need to cut an access hole through the top of the SOL-SB1600 side
work surface to allow the cables to be fed through to the other equipment. This can be
pre-cut by Sonifex when ordered as a SOL-CVRC, if a location is supplied when ordering.

Fitting the Optional SOL-T12 Top 19” Rack

Two black angled metal legs are used to support the SOL-T12 top 19” rack on the side
work-surface. There are holes in the top 19” rack and SOL-SB1600 side work surface to
accommodate the brackets.

• Fit the two large metal brackets in the appropriate holes in the SOL-SB1600 side work­surface. When viewed from the front edge the brackets angle backwards from the
base. Each bracket is secured with four 32-043 pan head slotted screws, M6 x 30mm,
with black plastic washers under the heads. These are fitted through the clearance
holes in the legs and into threaded inserts in the side work surface. This now provides
a support for the top 19” rack shown below : -

• Remove the two rear doors from the top 19” rack and position the top 19” rack onto
the two black metal legs. The top 19” rack will need supporting by an assistant while

Detail of adjustable feet in the SOL-B12
and on

the bottom of the SOL-LGG80

2

S2 SOLUT ION S S ING LE MIX ER FUR NIT URE IN STAL L AT ION

S2 SOLUTIONS SINGLE MIXER
FURNITURE UNSTALLATION

S2 Solutions Furniture User Handbook

7

you fit the eight 32-043 pan head slotted screws, M6 x 30mm with black plastic
washers under the heads, through the clearance holes in the legs and into threaded
inserts in the top 19” rack.

SOL-T12
Top 19” rack

SOL-T12
Black angled
metal legs

SOL-SB1600

Side

return

work

surface

SOL-B12
Support base
19” rack

Fig 4 : Fitting the Optional SOL-T12 Top 19” Rack.

Fitting the SOL-CVR80 Desk End Cover Panel

The end cover plate is used to cover the cable access holes in the SOL-SB1600 and the other
end of the SOL-MB1300 or SOLMB1500 mixer work surface. This is fitted with the two wood
screws and cups supplied.

Assembling U-Shaped S2 Solutions Single Mixer Furniture

If you have bought the additional SOL-SB1600 Side return and SOL-LGG80 Round legs to
make a U shape package, follow the instructions as above and then follow them again for
fitting the Side Work Surface and Main Work Surface using the new components on the
other side of the SOL-MB1300 or SOL-MB1500 mixer desk top. The SOL-CVR80 Desk end
cover panel should be fitted to cover the remaining access hole in the SOL-SB1600
Side return.

Your S2 Solutions Single Mixer furniture should now be successfully fitted together.

2

S2 SOLUTIONS SINGLE MIXER

FURNITURE UNSTALLATION

S2 SOLUT ION S S ING LE MIX ER FUR NIT URE IN STAL L AT ION

8

S2 Solutions Furniture User Handbook

S2 Solutions Single Mixer Furniture Full Assembly

S2 mixer
cut-ou

t

Top view

Side

view

1600

600

1500

900

425

630

735

Fig 5 : S2 Solutions Single Mixer Furniture Full Assembly (Dims in mm).

S2 SOLUT ION S S ING LE MIX ER FUR NIT URE IN STAL L AT ION

S2 SOLUTIONS SINGLE MIXER
FURNITURE UNSTALLATION

2

S2 Solutions Furniture User Handbook

9

3 S2 Solutions Split Mixer Furniture Installation

Your S2 Solutions package should arrive boxed or wrapped. Check the condition of the
boxes, packaging and woodwork and if any damage is evident report this to the carrier
before signing for the packages. Also report any damage immediately to Sonifex Ltd.

Each woodwork item is supplied with its relevant fixings. Make sure that you don’t throw the
fixings away in the packaging.

Main Components

SOL-MBR RH corner desk top that contains the right hand S2 split mixer.
SOL-MBL LH corner desk top that contains the right hand S2 split mixer.
SOL-MBC Mixer desk top centre section.
SOL-SB1000 Side return with joint boxes.
SOL-T12 (Optional) 12U top 19” rack straight double on legs.
SOL-B12 12U support base 19” rack.
SOL-D8 or SOL-D12 Desk top 19” rack (either 8U or 12U high).
SOL-LGG80 80mm silver/grey round table legs (pair).

The package has left and right hand corner mixer desk tops which are pre-cut to fit the
specific mixer sizes used. The SOL-SB1000 side returns are not handed and can be installed
on either the right or left hand side of the main mixing console.

Presenters seating

position

S2 mixe

r

cut-ou

t

SOL-SB1000
Side

return

work

surface

SOL-D8
Desk To

p

SOL-MBC
Centre

mixer desk top

work

surface

S2 mixe

r

cut-ou

t

SOL-SB1000

Side

return

work

surface

SOL-MBL
Left

hand mixer desk top

work

surface

SOL-MBR
Right hand

mixer desk top

work

surface

19” rack

Fig 6 : S2 Solutions Split Mixer Furniture, Viewed From Above.

3

S2 SOLUTIONS SPLIT MIXER

FURNITURE INSTALLATION

S2 SOLUT ION S S PLI T M IXE R F URN ITU RE INS TA LL ATI ON

10

S2 Solutions Furniture User Handbook

Assembly of the SOL-MBR, SOL-MBL and the SOL-MBC Mixer Work-Surfaces

• Clear an area of the floor to make sure that it is clean and free from debris (so as not to
mark the desk linoleum surface).

• Place the SOL-MBC mixer desk top centre section upside down on the floor with the
SOL-MBL LH and SOL-MBR RH mixer corner desk tops oriented as shown in Fig. 7. This
is done to aid the correct alignment of the three parts.

• The three parts are fixed together with four x M8 x 60mm bolts, eight large flat
washers and four M8 nuts supplied. These are inserted through holes in the SOL-MBC
mixer desk top centre section and the SOL-MBL LH and SOL-MBR RH mixer corner desk
tops.

• Screw the six SOL-LGG80 80mm silver/grey round table legs into the mounting plates
fitted in the LH, RH & centre mixer corner desk tops.

• Turn over the main mixer work surface assembly and stand it on the round legs, taking
care not to put side load on the round legs (Note: This part of the installation process
needs at least two people to perform it safely).

• Move these items by lifting the work surface, i.e. not by dragging it along the floor.

SOL-LGG80
Round Table Legs

Bolt
position

s

Bolt
position

s

SOL-LGG80
Round Table Legs

Fig 7 : S2 Solutions Split Mixer Work Surface Assembly.

Fitting the SOL-SB1000 Side Work-Surfaces

The SOL-SB1000 side returns can each be supported either by 2 x SOL-LGG80 80mm silver/
grey round table legs, or by the SOL-B12 12U support base 19” rack, depending on what you
have ordered.

S2 SOLUT ION S S PLI T M IXE R F URN ITU RE INS TA LL ATI ON

S2 SOLUTIONS SPLIT MIXER
FURNITURE INSTALLATION

3

S2 Solutions Furniture User Handbook

11

If fitting the SOL-SB1000 side return onto 2 x SOL-LGG80 80mm silver/grey round table legs :

• On a clear area of the floor, turn the SOL-SB1000 side return upside down and screw
the 2 x SOL-LGG80 80mm silver/grey round table legs into the leg mounting plates.

Fig 8 : Fitting SOL-LGG80 Legs to the SOL-SB1000 side return.

• Turn over the SOL-SB1000 side return and move it so that it fits up to either the
SOL-MBL LH or SOL-MBR RH mixer corner desk top. Take care not to put side load on
the round legs (move these items by lifting the work surface, i.e. not by dragging it
along the floor). Insert the small joint box and fit the two working surfaces together
with two x M8 x 140mm bolts four large flat washers and two M8 nuts. The bolts are
inserted through the SOL-SB1000 side return, the joint box and through the LH and
RH mixer corner desk tops.

If fitting the SOL-SB1000 side return onto the SOL-B12 12U support base 19” rack :

• Place the SOL-B12 12U support base 19” rack to the left or right of the proposed
presenters seat position and slightly behind it.

• The SOL-SB1000 side return is placed on top of the SOL-B12 12U support base 19”
rack, initially to act as a support.

• Move the SOL-SB1000 side return so that it fits up to either the SOL-MBL LH or SOL­MBR RH mixer corner desk top Insert the small joint box and fit the two working
surfaces together with two M8 x 140mm bolts, four large flat washers and two M8
nuts. The bolts are inserted through the SOL-SB1000 side return, the joint box and
through the LH and RH mixer corner desk tops.

S2 SOLUT ION S S PLI T M IXE R F URN ITU RE INS TA LL ATI ON

S2 SOLUTIONS SPLIT MIXER

FURNITURE INSTALLATION

3

SOL-LGG80
Round Table Legs
screw into

the

leg mounting

plates

12

S2 Solutions Furniture User Handbook

• Position the SOL-B12 12U support base 19” rack so that it’s front is under the front lip
of the SL-SB1000 side return.

Support Base
19” rack

Fig 9 : Assembling The SOL-SB1000 Side Return And SOL-B12 12U Support Base 19” Rack.

Fitting the SOL-D8, or SOL-D12 Desk Top 19” Rack

The SOL-D8 or SOL-D12 desk top 19” rack simply sits on the linoleum worktop of the SOL­SB1000 side work surface. If you are fitting the free standing SOL-D8 or SOL-D12 desk top
19” rack, you will need to cut an access hole through the top of the SOL-SB1000 side work
surface to allow the cables to be fed through to the other equipment. This can be pre-cut by
Sonifex when ordered as a SOL-CVRC, if a location is supplied when ordering.

Fitting the Optional SOL-T12 Top 19” Rack

Two black angled metal legs are used to support the SOL-T12 top-pod on the side work­surface. There are holes in the top pod and SOL-SB1000 side work surface to accommodate
the brackets.

• Fit the two large metal brackets in the appropriate holes in the SOL-SB1000 side work­surface. When viewed from the front edge the brackets angle backwards from the
base. Each bracket is secured with four 32-043 pan head slotted screws, M6 x 30mm,

3

S2 SOLUT ION S S PLI T M IXE R F URN ITU RE INS TA LL ATI ON

S2 SOLUTIONS SPLIT MIXER
FURNITURE INSTALLATION

S2 Solutions Furniture User Handbook

13

with black plastic washers under the heads. These are fitted through the clearance
holes in the legs and into threaded inserts in the side work surface. This now provides
a support for the top 19” rack shown below (Fig 10): -

• Remove the two rear doors from the top 19” rack and position the top 19” rack onto
the two black metal legs. The top 19” rack will need supporting by an assistant while
you fit the eight 32-043 pan head slotted screws, M6 x 30mm with black plastic
washers under the heads, through the clearance holes in the legs and into threaded
inserts in the top 19” rack.

SOL-SB1600

Side

return

work

surface

SOL-T12
Top 19” rack

SOL-T12
Black angled
metal legs

SOL-B12
Support base
19” rack

Fig 10: Fitting the Optional SOL-T12 Top 19” rack.

Your S2 Solutions Split Mixer furniture should now be successfully fitted together.

3

S2 SOLUT ION S S PLI T M IXE R F URN ITU RE INS TA LL ATI ON

S2 SOLUTIONS SPLIT MIXER

FURNITURE INSTALLATION

14

S2 Solutions Furniture User Handbook

S2 Solutions Split Mixer Furniture Full Assembly

S2 mixer
cut-ou

t

S2 mixe

r

cut-ou

t

Top View

2000

2200

425

630

735

600

1000

1000

Side

View

Fig 11 : S2 Solutions Split Mixer Furniture Full Assembly (Dims in mm).

S2 SOLUT ION S S PLI T M IXE R F URN ITU RE INS TA LL ATI ON

S2 SOLUTIONS SPLIT MIXER
FURNITURE INSTALLATION

3

S2 Solutions Furniture User Handbook

15

S2 SOLUT ION S F URN ITU RE USE R H AND BOO K

S2 SOLUTIONS FURNITURE

USER HANDBOOK

w w w . s o n i f e x . c o . u k

t:[phone]
f:[phone]
sa l es @ so n ife x. c o. uk