Sonicwall 02C Users Manual

SonicWALL SonicPoint - Model APL13-02C

FCC Part 15 Class A Notice

NOTE: This equipment was tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy. And if
not installed and used in accordance with the instruction manual, the device may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user is required to correct the interference at
his own expense.

Complies with EN 55022 Class A and CISPR22 Class A.
*Refer to the label on the bottom of the unit for device information including Class A or Class

B FCC information.

Caution: Modifying this equipment or using this equipment for purposes not shown in this
manual without the written consent of SonicWALL, Inc. could void the user’s authority to
operate this equipment.

BSMI Statement

VCCI Statement

Page 1

Canadian Radio Frequency Emissions Statement

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à toutes la norme NMB-003 du Canada.

CISPR 22 (En 55022) Class A

Warning: This is a class A product. In a domestic environment, this product may cause radio

interference in which case the user may be required to take adequate measures.

Declaration of Conformity

Application of council Directive Directive 89/336/EEC (EMC) and

Standards to which conformity is declared EN 55022 (1998) Class A

72/23/EEC (LVD)

Directive 1999/5/EC (R&TTE) and standards

EN 301 489-1/-17 and EN 300 328-1/-2

EN 55024 (1998)
EN 61000-3-2 (1995) + A1, A2, A14
EN 61000-3-3 (1994)
EN 60950 (1992) + A1, A2, A4, A11

National Deviations: AT, AU, BE, CH, CN, CZ,
DE, DK, FI, FR, GB, GR, HU, IE, IL, IN, IT, JP,
KR, NL, NO, PL, SE, SG, SI

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20
centimetres (7.9 inches) between the radiator (antenna) and your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.

For more information regarding the above statement, please contact SonicWALL, Inc. at 1143
Borregas Avenue, Sunnyvale, CA 94089-1306 or 1-408-745-9600.

Cable Connections

All Ethernet and RS232 (Console) cables are designed for intra-building connection to other
equipment. Do not connect these ports directly to communication wiring or other wiring that
exits the building where the SonicWALL is located.

Power Supply Information

If the power supply is missing from your SonicWALL product package, please contact
SonicWALL Technical Support at 408-752-7819 for a replacement. This product should only be
used with a UL listed power supply marked “Class 2” or “LPS”, with an output rated 5 VDC,
minimum 1.66 A.

Page 2

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of
the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not ca use
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to
operate this equipment.

Canada (IC):
To prevent radio interference to the licensed service, this device is intended to be
operated indoors and away from windows to provide maximum shielding. Equipment
(or its transmit antenna) that is installed outdoors is subject to licensing.

Canada (IC):

To prevent radio interference to the licensed service (i.e. co-channel Mobile Satellite
systems) this device is intended to be operated indoors and away from windows to
provide maximum shielding. Equipment (or its transmit antenna) that is installed
outdoors is subject to licensing.