1
Introduction
Thank you for purchasing Sonance Visual Performance®SingleStereo Technology
®
(SST) and surround (SUR) speakers. When
properly installed your new speakers will give you years of entertainment pleasure. This manual covers the following speaker
models: VP65R SST; VP65R SUR, VP65S SST, VP65S SUR, VP65 SST.
Box Contents
IItteemm QQuuaannttiittyy ((SSSSTT)) QQuuaannttiittyy ((SSUURR))
Visual Performance Speaker 1 2
Paintable Grille 1 2
Plastic Paint Plug 1 2
Mounting Cutout Template 1 1
Speaker Placement
SST Models
Because a single SST speaker reproduces both stereo channels
from a single location, it will deliver outstanding performance
from a wide variety of mounting locations where a pair of stereo
speakers would be impractical, including hallways, bathrooms
and closets.
The table below shows how far apart SST speakers can be
spaced in distributed audio applications while still providing
good coverage for standing and seated listeners (see
Figure 1
).
CCeeiilliinngg HHee iigghhtt SSppaacciinngg ((SSttaannddiinngg)) SSppaacciinngg ((SSeeaatteedd))
9-Foot Ceiling 5’7” 9’5”
10-Foot Ceiling 9’7” 13’5”
12-Foot Ceiling 13’7” 17’5”
14-Foot Ceiling 17.7’ 21.5’
SUR Models: 5.1-Channel Home Theater System
Mount the left and right surround speakers on the ceiling
between 2 feet and 6 feet behind the listening position.
The speakers should be between 6 feet and 10 feet apart. Orient
the speakers so the tweeters face the front and rear walls of the
room. Use
Figure 2
as a guide.
SUR Models: 7.1-Channel Home Theater System
Mount the left and right surround speakers directly to the sides of
the listening position, between 6 feet and 10 feet apart. Mount
the surround back speakers between 2 feet and 6 feet behind the
listening position. The surround back speakers should be closer
together than the left and right surround speakers — between
3 feet and 6 feet apart. Use
Figure 3
as a guide.
Before Installation: Retrofit
1. Determine the location for the speaker (see
Speaker Placement
above).
S
AFETY W ARNING:
THESE SPEAKERS HAVE FASTMOUNT
®
TABS THAT PREVENT THE
SPEAKERS FROM FALLING OUT OF THE MOUNTING HOLES
DURING THE INSTALLATION PROCESS.
THE EDGES OF THE FASTMOUNT TABS ARE VERY
SHARP.
USE CAUTION WHEN HANDLING THE SPEAKERS.
C
OVERAGE
A
REA
C
OVERAGE
A
REA
S
PEAKER
S
PACING
FIGURE 1: DISTRIBUTED AUDIO COVERAGE AREA
TV
3' – 6'
apart
2' – 6'
Surround
Back
Speaker
Surround
Back
Speaker
Right Surround
Speaker
Left Surround
Speaker
F
IGURE 3: SUR SPEAKER PLACEMENT IN A 7.1-CHANNEL SYSTEM
INSTRUCTION MANUAL
VISUAL PERFORMANCE® SERIES
6” SST AND SUR SPEAKERS
TV
6' – 10'
apart
2' – 6'
Right Surround
Speaker
Left Surround
Speaker
FIGURE 2: SUR SPEAKER PLACEMENT IN A 5.1-CHANNEL SYSTEM
2
SONANCE VISUAL PERFORMANCE®6” SST & SUR
2. Perform an obstruction survey to be certain that there are no
studs, conduit, pipes, heating ducts, pocket doors or air returns
in the wall or ceiling cavity that will interfere with the speaker.
3. Mounting cutout dimensions and depth requirements:
• VP65R SST/VP65R SUR: Cutout Diameter = 8
3
/
16” (208mm);
Depth = 4
13
/
16” (122mm).
• VP65S SST/VP65S SUR: Cutout H x W = 8
3
/
16”x 8
3
/
16”
(208mm x 208mm); Depth = 4
13
/
16” (122mm).
• VP65 SST: Cutout H x W = 6¾" x 10
5
/
8" (172mm x 270mm),
Depth = 3
9
/
16” (91mm)
4. Position the included cutout template where the speaker is to
be located and pencil an outline on the wall or ceiling.
• If you are unsure about obstructions, drill a small hole in the
center of the outline and insert a coat hanger wire into the
hole to feel-around for possible obstructions.
5. Cut the mounting hole using a keyhole or drywall saw, and
run the speaker wires from the mounting hole to the amplifier
location.
• Consult local building codes before running speaker wires
through ceilings.
Installation
Visual Performance SST AND SUR speakers feature exclusive
FastMount
®
tabs and an integral RotoLock®mounting system for
quick mounting directly into existing walls and ceilings.
WARNING: The edges of FastMount tabs are very
sharp. Use caution when handling the speaker.
1. Remove the paint plug from the speaker.
2. Run speaker wire from each speaker to the amplifier location.
3. Strip ¼” – ½” of insulation from each speaker lead. Twist the
strands or tin the exposed wire with solder to ensure that there
are no stray strands. (Stray strands that touch each other can
cause a short-circuit that can damage the amplifier.)
4. The speaker’s connector posts are spring-loaded. Push the top
of each connector post down to open the connector and insert
the exposed wires into the holes in the posts.
• The speaker’s positive post is labeled with a red dot; the negative post is labeled with a black dot. Double-check that you
connected amplifier
“+” to speaker “+”
and amplifier “–” to
speaker “–”.
5. Make sure all the
RotoLock clamps are
in the full clockwise
position so that they
are tucked within the
mounting hole’s
border. Insert the
speaker into the hole
in the wall or ceiling
(
Figure 4
). The
RotoLock system can
accommodate a
maximum wall or
ceiling material
thickness of 1¼”.
• The FastMount tabs
will prevent the
speaker from falling
out of the mounting
hole, allowing the
installer to let go of
the speaker to pickup tools or other
items (
Figure 5
).
N
OTE : THE
F
ASTMOUNT TABS
ARE DESIGNED FOR
ONE-TIME USE ONLY.
IF THE SPEAKER IS
REMOVED FROM THE MOUNTING HOLE THE FASTMOUNT TABS
WILL DISCONNECT AND REMAIN INSIDE THE WALL OR CEILING
.
6. Tighten the four screws on the front of the speaker baffle
(
Figure 6
). The RotoLock clamps will automatically rotate into
position and begin clamping the speaker.
• When you notice resistance on the screws the speaker has
been clamped successfully.
IMPORTANT: Always use low-torque settings;
NEVER over-tighten.
N
OTE : ADJUSTING THE TENSION OF THE ROTOLOCK CLAMPS SO
THAT THE SPEAKER FRAME IS FLAT WILL HELP ENSURE THAT THE
GRILLE CONTACTS THE WALL ALL THE WAY AROUND THE SPEAKER
FOR A PROPER FIT.
7. The new micro flange grille is held in place by several small,
powerful magnets on the speaker frame. Place the grille
against the speaker and the magnets will hold it firmly in
place. When properly installed, the grille flange should make
contact with the wall all the way around the speaker.
RotoLock Clamps
(retracted)
FIGURE 4: INSERT SPEAKER INTO
MOUNTING HOLE
RotoLock
Screws
RotoLock
Screws
FIGURE 6: TIGHTENING THE ROTOLOCK SCREWS
FastMount Tabs
F
IGURE 5: FASTMOUNT TABS
3
SONANCE VISUAL PERFORMANCE®6” SST & SUR
Speaker Adjustments
Pivoting Woofer
The VP65R SST/SUR, and VP65S SST/SUR models have a
pivoting woofer assembly. This allows you to direct sound toward
or away from the listening area, depending on how the speakers
are being used:
• For SST models, pivoting the woofer towards the listening
position will maximize the speaker’s clarity and definition.
• For SUR models, you can create a more diffuse, spacious
surround effect by aiming the woofers towards a wall or
window, away from the listeners.
NOTE
: WHEN P IVOTING THE WOOFERS IN
SUR MODEL
SPEAKERS
,
MAKE SURE THAT THE TWEETERS REMAIN ORIENTED
TOWARDS THE FRONT
AND REAR WALLS
FOR SIDE SURROUND
SPEAKERS
, AND TOW-
ARDS THE SIDE WALLS
FOR SURROUND BACK
SPEAKERS.
To pivot the woofer,
apply pressure on
the outer edge of
the tweeter support
bracket, as shown in
Figure 7
. Do not touch
or apply pressure to
the woofer cone.
Painting The Speakers and Grilles
Please refer to the included
Painting Instructions
sheet.
Specifications
VP65R SST, VP65S SST, VP65 SST,
VP65R SUR, VP65S SUR
Tweeter: 1" (25mm) Silk dome,
Ferrofluid-cooled, pivoting,
in acoustic back chamber
Woofer: 6½" (165mm) Carbon fiber
cone with a rubber surround,
pivoting (VP65R, VP65S)
Frequency Response: 44Hz – 20kHz ±3dB
Impedance: 8 ohms nominal;
6 ohms minimum
Power Handling: 5 watts minimum;
130 watts maximum
Sensitivity: 90dB SPL (2.83V/1 meter)
Grille Material: Perforated Steel
Dimensions
VP65R SST/SUR (Dia. x D): 9¼" x 4
13
/
16"
(234mm x 122mm)
VP65S SST/SUR (H x W x D): 9¼" x 9¼” x 4
13
/16"
(234mm x 234mm x 122mm)
VP65 SST (W x H x D): 7
13
/
16" x 11
11
/
16" x 3
9
/
16”
(198mm x 297mm x 91mm)
Cutout Dimensions
VP65R SST/SUR (Dia): 8
3
/
16
” (208mm)
VP65S SST/SUR (W x H): 8
3
/
16”x 8
3
/
16”
(208mm x 208mm)
VP65 SST (W x H): 6¾” x 10
5
/8"
(172mm x 270mm)
Shipping Weight:
VP65R/VP65S/VP65 SST: 5 lbs (2.3kg) each
VP65R/VP65S SUR: 10 lbs (4.5kg) pair
F
IGURE 7:
P
IVOTING THE WOOFER
Technical Assistance and Service
If you any have questions about the operation or installation of this product, please call our Technical Assistance
Department on any business day at (800) 582-0772 or (949)
492-7777; from 7 a.m. to 5 p.m., PST.
If your speakers should need repair or service, contact your Sonance
Authorized Dealer for help, or use the following procedure:
1. Prior to calling, note the product’s model number, serial number,
purchase date, and the name and address of the dealer where you
purchased the product.
2. Contact our Technical Assistance Department at the above num-
ber(s) and describe the problem the unit is experiencing. If applicable, they will issue a Return Authorization Number.
IMPORTANT: YOU MUST HAVE PRIOR AUTHORIZATION TO
RETURN YOUR SPEAKER TO SONANCE!
3. If you’re directed to return the unit to Sonance for repair, pack the
unit in its original shipping carton. If needed, you can obtain
replacement packaging from us for a small charge. Note: it is best
if you place the box into an additional outer “overcarton” before
shipment to minimize a chance of theft in shipment. Please include
a copy of the original bill of sale inside the package.
4. Contact a package delivery company such as United Parcel
Service or Federal Express to arrange prepaid (not collect)
shipping. Do not use the U.S. Postal Service.
IMPORTANT: Freight collect shipments will be refused.
5. Write the Return Authorization Number on the outside of
the shipping carton.
6. Ship the packaged unit to:
Quality Assurance Department
Sonance
212 Avenida Fabricante
San Clemente, CA 92672-7531
Limited Lifetime Warranty Coverage
(U.S. Only)
Sonance warrants to the original retail purchaser only that
this Sonance product will be free from defects in materials
and workmanship, provided the speaker was purchased
from a Sonance Authorized Dealer.
Defective products must be shipped, together with proof of purchase,
prepaid insured to the Authorized Sonance Dealer from whom they
were purchased, or to the Sonance factory at the address listed on
this instruction manual. Freight collect shipments will be refused. It is
preferable to ship this product in the original shipping container to
lessen the chance of transit damage. In any case, the risk or loss or
damage in transit is to be borne by the purchaser. If upon examination at the factory or Authorized Sonance Dealer it is determined that
the unit was defective in materials or workmanship at any time during this warranty period, Sonance or the Authorized Sonance Dealer
will, at its option, repair or replace this product at no additional
charge, except as set forth below. If this model is no longer available
and can not be repaired effectively, Sonance, at is sole option, may
replace the unit with a current model of equal or grater value. In
some cases where a new model is substituted, a modification to the
mounting surface may be required. If mounting surface modification
is required, Sonance assumes no responsibility or liability for such
modification. All replaced parts and product become the property of
Sonance. Products replaced or repaired under this warranty will be
returned to the original retail purchaser, within a reasonable time,
freight prepaid.
This Warranty does not include service or parts to repair damage
caused by accident, disaster, misuse, abuse, negligence, inadequate
packing or shipping procedures, commercial use, voltage inputs in
excess of the rated maximum of the unit, or service, repair or modification of the product which has not been authorized or approved
by Sonance. This Warranty also excludes normal cosmetic deterioration caused by environmental conditions. This Warranty will be void
if the Serial Number on the product has been removed, tamperedwith or defaced. This Warranty is in lieu of all other expressed warranties. If the product is defective in materials or workmanship as
warranted above, the purchaser’s sole remedy shall be repair or
replacement as provided above. In no event will Sonance be liable
for any incidental or consequential damages arising out of the use or
inability to use the product, even if Sonance or an Authorized
Sonance Dealer has been advised of the possibility of such damages,
or for any claim by any other party.
Some states do not allow the exclusion or limitation of consequential
damages, so the above limitation and exclusion may not apply. All
implied warranties on the product are limited to the duration of this
expressed Warranty. Some states do not allow limitation on the
length of an implied warranty. If the original retail purchaser resides
in such a state, this limitation does not apply.
Exclusions And Limitations
The warranty set forth above is in lieu of all other warranties,
express or implied, of merchantability, fitness for a particular
purpose, or otherwise. The warranty is limited to Sonance products
registered herein and specifically excludes any damage to
loudspeakers and other allied or associated equipment which may
result for any reason from use with this product. Sonance shall, in no
event, be liable for incidental or consequential damages arising from
any breach of this warranty or otherwise. This warranty gives you
specific legal rights, and you may have other rights which vary from
state to state.
©2008 Sonance. All rights reserved. Sonance, Sonance Visual Performance, Single-Stereo Technology, RotoLock and FastMount
are registered trademarks of Dana Innovations.
Due to continuous product improvement, all features and specifications are subject to change without notice.
For the latest Sonance product specification information visit our website: www.sonance.com
212 Avenida Fabricante • San Clemente, CA 92672-7531 USA • (800) 582-7777 or (949) 492-7777 • FAX: (949) 361-5151
Technical Support: (800) 582-0772
www.sonance.com
33-4942 06/08
Loading...