Sonance SB46 M, SB46 L Owner's Manual
INSTALLATION MANUAL
SONANCE SOUNDBARS
SB46 M AND SB46 L
Introduction
Thank you for purchasing the Sonance Soundbar SB46 M or
SB46 L. When properly installed your new Soundbar will give you
years of entertainment pleasure. The Sonance SB46 M & SB46 L
Soundbar is a high performance Left, Center, & Right
3-way speaker system housed in a sealed aircraft grade
aluminum enclosure. The SB46 M will align with displays from
50” to 65” diagonal. The SB46 L will align with displays from
70” to 80” diagonal.
Box Contents
Sonance Soundbar Box contains: (1) Soundbar, (2)
Flat Soundbar connectors, (2) Display attachment rails,
(2) Recessed Soundbar connectors, (1) Key hole wall mount
template, (2) Key hole wall mounts, (2) Display spacers and
(2) Black opaque strips.
(1) Soundbar
(2) Flat Soundbar connectors
(2) Recessed
Soundbar connectors
The Hardware Pack contains: A. (4) M8 10mm screws
for display attachment rails, B. (4) M8 14mm screws for
flat Soundbar connector, C. (4) M8 23mm short screws for recessed
Soundbar connector, D. (4) M8 38mm long screws for recessed
Soundbar connector, E. (4) M6 25mm screws, F. (4) M8 25mm
screws, G. (8) M8 nuts, H. (8) M6 washers, I. (8) M8 washers and J.
(4) Rubber feet.
A. x 4
G. x 8
D. x 4
H. x 8 I. x 8
B. x 4
E. x 4
C. x 4
F. x 4
J. x 4
Wall Mount Installations
Verify the wall mount will support the combined
weight of the display and Soundbar.
SB46 M weighs 24 lbs. (10.88 kg) installed. Suitable for displays
50” to 65” (1270mm to 1651mm).
(2) Display attachment rails
wall mount template
(2) Key hole
wall mounts
(1) Key hole
(2) Black opaque strips
(2) Display spacers
SB46 L weighs 29 lbs. (13.15 kg) installed. Suitable for displays
70” to 80” (1778mm to 2032mm).
NOTE: CAREFULLY FOLLOW INSTALLATION DIRECTIONS FOR
THE THIRD PARTY DISPLAY WALL MOUNT.
Before any installation carefully plan where wiring will pass
through walls. Perform an obstruction survey using a stud finder
to be certain there are no studs, conduit, pipes, heating ducts,
pocket doors or air returns in the wall cavity. If you are unsure
about obstructions, drill a small hole near where the Soundbar
wire terminals will be located and insert a coat hanger wire
into the hole to feel around for possible obstructions.
Run three sets of speaker wires: Left channel, Center channel,
Right channel as well as the necessary video cable from the
amplifier to the display location. Whenever possible leave extra
wire to make it easy to connect the wire to the Soundbar spring
terminals prior to hanging the display. Extra wire can then be
pushed back into the wall.
NOTE: CONSULT LOCAL BUILDING CODES BEFORE RUNNING
SPEAKER AND ELECTRICAL WIRES THROUGH WALLS.
1
SONANCE SOUNDBARS SB46 M AND SB46 L
Soundbar Placement and
Options Overview
Soundbar SB46 M and SB46 L are designed to attach directly to
most flat panel display wall mounts using VESA mounting points
with the included attachment rails, connectors, and hardware.
Mounting Option 1 - Flat Soundbar Connector
The Flat Soundbar Connector will align with displays 2 5/8”
(65mm) deep.
Mounting Option 2 -
The Recessed Soundbar Connector will align with displays from
1 7/32” - 2 3/32” (31.74mm - 53mm) deep.
Mounting Option 3 - Table Top
Soundbars can additionally be cabinet or table top mounted using
the rubber feet included in your box contents.
Mounting Option 4 - Key Hole Wall Mount
Key hole wall mounting is an alternative option accomplished by
using the key hole wall mounts combined with the wall mount
template.
Recessed Soundbar Connector
Soundbar Connectors for Wall Mount Brackets
Choose and attach the correct Soundbar connector to the
display attachment rails for your desired depth.
The flat Soundbar connector will align with 2 5/8” (65mm)
deep displays. The recessed Soundbar connector will align with
displays from 1 7/32” - 2 3/32” (31.74mm - 53mm) deep.
Mounting option 1:
F
lat Soundbar ConneCtor
Mounting option 2:
r
eCeSSed Soundbar ConneCtor
Step 1
Mounting Option 1 - Flat Soundbar Connector
The flat Soundbar connector will align with 2 5/8” (65mm)
displays. Use the A screws to connect to the display
attachment rails.
Mounting option 1:
F
lat Soundbar ConneCtor
Mounting option 3:
t
able top
2
Mounting option 2:
r
eCeSSed Soundbar ConneCtor
Mounting option 4:
K
ey Hole Wall Mount
A
Mounting optio n 1 - Flat So un db ar Con ne Cto r
SONANCE SOUNDBARS SB46 M AND SB46 L
Display Spacers
Included with your Soundbar are two 8mm thick wood display
spacers. The spacers allow the front surface of the display to be
in line with the flat surface on the top edge of the Soundbar.
When using the spacers carefully place the display on top of
the spacers. This will require two people. Be careful not to
scratch the display. Spacers do not go under the Soundbar.
Mounting Option 2 - Recessed Soundbar Connector
The recessed Soundbar connector will align with displays from
1 7/32” (31.74mm) to 2 3/32” (53mm) deep displays.
Various depths can be accomplished by using C or D screws
accompanied by I washers and G nuts. Use the A screws to
attached the connector to the display attachment rails.
C or D
A
G
Display Spacer
Variable dep tH S Fo r Va ri ou S di Sp lay tHi CK ne SS eS
If the spacers are not used the front
surface of the display will be in line
with the front radius of the Soundbar
grille. This is dependent on the display
thickness and installation preference.
Proceed to Step 2
I
Mounting optio n 2 - reCeSSed Sou nd ba r Co nn eC tor
M
ult ip le dep tH opt io nS uSi ng nut S an d Wa SH er S
Proceed to Step 2
3
Loading...