OMNI-6T
OMNIDIRECTIONAL OUTDOOR SPEAKER
INSTRUCTION MANUAL
Omnidirectional Outdoor Speaker
OMNI-6T
IMPORTANT SAFETY INSTRUCTIONS
This product is intended to be installed by professional
AV integrators and installers only. This product manual
is intended to serve as a general guideline for most
applications. It is the installer’s responsibility to ensure
this product is installed in accordance with local
building codes and regulations. Consult a local authority
for specific requirements, regulations, and building
codes of the jurisdiction in which this product is to be
installed.
READ THIS DOCUMENT IN ITS
ENTIRETY BEFORE ATTEMPTING
INSTALLATION.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
TABLE OF CONTENTS
1 Important Safety Instructions and Box Contents
2 Product Description
2 Product Features
3 Product Preparation
3 Installation
6 Technical Specifications
7 Architectural Specification
7 Technical Assistance and Service
8 Warranty
5. Clean only with a dry cloth.
6. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
7. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
8. Only use attachments/accessories specified by
Sonance.
9. Refer all servicing to qualified service personnel.
BOX CONTENTS
(1) OMNI-6T Speaker
(2) Silicone-Filled Wire Nuts
(1) Installation Manual
1
PRODUCT DESCRIPTION
The Sonance OMNI-6T In-Ground Omnidirectional
Speaker utilizes a unique, perimeter-firing driver array
paired with an up-firing 6.5” woofer in a discreet,
weatherized housing. Exceptional omnidirectional
coverage is achieved while maintaining fidelity
throughout the midrange and treble via direct radiation
of the four wide-band canopy drivers. With the addition
of a sealed woofer firing upward and through the
speaker’s canopy grille, true full-range response is
attained with even, broadband omnidirectivity. The
small form-factor, earth-tone brown enclosure makes
this outdoor speaker remarkably easy to hide in
landscaping environments, against soil/mulch, and in
the shadows of foliage. Bury the OMNI-6T for optimal
performance and security or anchor above ground
for hardscape applications (stainless steel mounting
hardware not included). An internal 70V/100V highoutput transformer allows installation in sprawling
properties—especially commercial projects. A
side-accessible tap switch provides easy switching
between transformer taps and can be bypassed for
low-impedance (8 ohm) operation. Used on its own
or as part of the Sonance Landscape Series outdoor
speaker systems, the OMNI-6T delivers excellent, fullrange omnidirectional coverage for eciently solving
coverage challenges and creating immersive, highfidelity outdoor audio experiences.
PRODUCT FEATURES
• Wideband, 4-driver array provides true
omnidirectional coverage with full fidelity
• Full-range response with up-firing 6.5” woofer
• IP66 rated for all-season use
• 80W 70V/100V transformer with Sonance
Laminated Core Technology
• Multiple transformer taps and 8 Ohm bypass
settings speed installation time and allow for
adjustments even after installation
• Weatherized, earth-tone brown, mineral-filled
polypropylene housing makes the OMNI-6T
disappear in landscaping and behind foliage
• Bury the speaker in-ground or secure above-ground
for flexible installation options
• Use in multiples or as part of the Sonance
Landscape Series to complete any professional
outdoor audio system
PRODUCT FEATURES
Mineral-Reinforced
Polypropylene Enclosure
6.5” Woofer
Hi-Def Crossover
Laminated Core
Hardscape Security
Mount Points
4-Driver
Omnidirectional
Array
80W Sonance
Transformer
Transformer Tap Switch
2
PRODUCT PREPARATION
70V
OFF
20
40
80
NA
8Ω
OFF
20
40
80
8Ω
10
100V
AMPLIFIER SELECTION
When choosing an amplifier, the maximum number of
speakers and the output level of each speaker must be
known. The sum of the tap settings should never exceed
80% of the amplifier’s rated output. For example, if
there are 5 speakers and the taps are set at 20 watts,
the load would be 100 watts (5 x 20 watts = 100 watts).
To arrive at the needed power for this number of
speakers, simply divide the total load by 0.8. In this
case, 100 / 0.8 = 125 watts. Therefore, a standard 125
watt amp would safely drive this load. To calculate the
amount of usable power an amp oers, simply multiply
the rated output by 0.8, i.e., 125 watts x 0.8 = 100 watts.
WIRE GAUGE – 70V/100V SYSTEM
The most common wire used on commercial 70
volt systems is 18 gauge, 2 conductor, stranded, and
jacketed without a shield. For outdoor applications,
direct burial type wire is recommended. The wire
starts at the amplifier location and is paralleled at each
speaker location. Maximum recommended wire length
using 18 gauge is up to 700 feet with a 100 watt load.
If you double the load (sum of your tap settings), you
will reduce the footage by half, to 350 feet. Conversely,
if you halve the load, you may double the acceptable
wire length, i.e., a 50 watt load is safe over 1400 feet
of 18 gauge. Stepping up to 16 gauge wire extends
the allowable run length by approximately 35%. For
example, a 100 watt load can go 700 feet on 18 gauge;
the same load may be placed on 1100 feet of 16 gauge.
INSTALLATION
In a typical 70V/100V mono configuration, multiple
OMNI-6T units can be wired in parallel along a single
2-conductor wire. Alternatively, a 4-conductor wire can
be used to alternate left and right channels for a stereo
configuration.
NOTE: Before placing speakers in their final locations,
ensure that each tap is set to the appropriate 70V/100V
or 8 Ohm setting (Figure 2). Never connect multiple
speakers set at 70V/100V and 8 Ohm to the same
circuit.
ADJUSTING THE TRANSFORMER
TAP SETTINGS
WIRE GAUGE – 8 OHM SYSTEM
When using the product in an 8 Ohm system, the
total wire resistance should be less than 10% of the
speaker impedance. The speakers are nominally 6
Ohms impedance, so your total wire resistance should
be no more than 0.6 Ohms. In simple terms, the extra
resistance from the wire will have a very negative aect
on the sound quality of the speaker. The sound can
be less dynamic, definition of bass frequencies can be
reduced, and in extreme cases, the high frequencies
can be attenuated. Amplifier power is also wasted in
the wire, reducing the maximum output level of the
system. Please refer to the following chart (Figure 1)
when deciding on the appropriate wire gauge for
your installation.
WIRE RESISTANCE IN OHMS VS. LENGTH OF CABLE RUN
DISTANCE IN FEET 50’ 100’ 150’ 200’ 250’ 300’
20 GAUGE .86 1.73 2.59 3.45 4.32 5.18
18 GAUGE .65 1.30 1.94 2.59 3.24 3.89
16 GAUGE .43 .85 1.28 1.71 2.14 2.56
14 GAUGE .27 .54 .81 1.08 1.35 1.62
12 GAUGE .17 .34 .51 .68 .85 1.02
Figure 1: Wire Resistance
Figure 2: Adjusting the Transformer Tap Settings
IMPORTANT: This product is IP66-rated for use in harsh
outdoor environments. Nevertheless, careful placement
of the speakers to reduce exposure to direct water
spray is recommended.
CAUTION: The amplifier should not be connected to AC
power until all speaker wire connections are completed.
70V/100V amplifiers present a serious shock hazard.
SPEAKER PLACEMENT
The Omni-6T is designed to deliver a seamless, 360
degree omnidirectional sound field in an open air
environment. An array of multiple speakers should be
strategically placed to minimize ‘hot spots’ and ‘nulls’
as you move around the outdoor entertainment area.
Recommended placement of the Omni-6T speakers
is every 10-15 ft (3-4.5m) around the listening area for
ideal coverage. The shorter spacing is recommended for
higher SPL and closer listening applications (Figure 3).
Minimum spacing is every 30 ft (7.5m) but may result
in non-optimal coverage. For optimal performance and
visual integration into softscaping, bury each speaker
6-8 inches (Figure 4). In hardscaping applications, use
3
the four 1/4” (6mm) mounting holes in the base to
secure the speaker onto its installation surface (stainless
steel mounting hardware not included).
- OMNI 6-T Speaker
Residential Speaker Placement
DINING
2. Prepare the wires to be connected by stripping back
the insulation to expose approximately 1/2” of
copper. Combine the positive (+) wires from the
amplifier, the speaker, and the line running to the
next speaker. Using the included silicone filled wire
nuts, twist the wires together ensuring that no
copper is exposed (Figure 5). Repeat the same
process for the negative (-) wires.
Figure 5: Wire Connections
Figure 6: Cable Stripper
3. When both connections at the speaker are complete,
use a zip tie to manage the extra slack and provide
strain relief to the connection.
4. Place the speaker over the completed wire
connections.
EVENT SPACE
- OMNI 6-T Speaker
Commerical Speaker Placement
Figure 3: Speaker Placement
Figure 4: Speaker Placement
RECEPTION
CONFERENCE
ROOMS
LOBBY
12” (305mm)
OFFICES
3” (76mm)
EVENT CENTER
7” (178mm)
MONO CONFIGURATION
1. Run a single direct burial type 2-conductor wire
from the amplifier’s location out to the furthest
speaker location, passing through each speaker
location along the way. Leave an extra 12-18” of
wire at each speaker location for making your
speaker connections.
5. Repeat steps 2 through 4 at each speaker location.
See the AMPLIFIER CONNECTIONS SECTION for
more detailed wiring diagrams.
ALTERNATING LEFT/RIGHT
STEREO CONFIGURATION
1. Run a single direct burial type 4-conductor wire
from the amplifier’s location out to the furthest
speaker location, passing through each speaker
location along the way. Leave an extra 12-18” of
wire at each speaker location for making your
speaker connections.
2. Using a radial cable stripper (Figure 6), prepare
the wires to be connected by stripping back the
outer jacket to expose the four individual wires
(Figure 7). Assuming the first speaker is designated
as the Left channel, cut the Left (+) and Left (-)
wires (typically white/green) (Figure 8). Combine
the positive (+) wires from the amplifier, the
speaker, and the line running to the next speaker.
Using the included silicone filled wire nuts, twist
the wires together ensuring that no copper is
exposed. Repeat the same process for the negative
(-) wires. The other two wires should be left intact,
as they will be used at the next speaker.
4
1-L 1-R 2-L
IN
OUTINOUT
SONANCE DSP2-750
S/N
CAUTION
MADE IN CHINA
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS
RISQUE DE CHOC ELECTRIQUE
2-R
1- LEFT
CLASS 2 WIRING
NE PAS OUVRIR
275 watts
IR
IR
CONTROL
STATUS
T15AL / 250VAC
CAUTION
IN
REPLACE FUSE ONLY
WITH
SAME TYPE AND RATING
AC 100-120V ~ 60Hz
ATTENTION
REMPLACER UNIQUEMENT AVEC
VOLTAGE TRIGGER
AC 220-240V ~ 50Hz
LE MEME TYPE ET CALIBRE DU
1- RIGHT
FUSIBLE
IN OUT
OUT
TCP/IP
3-30 VOLTS
BRIDGE
DHCP ON - DEFAULT
AC or DC
Ω
MIN
8
+ +
Figure 7: Wire Jacket Removed
White/Green = Left
Red/Black = Right
Figure 8: Prepared Wires
3. When both connections at the speaker are complete,
use a wire tie to manage the extra slack and provide
strain relief to the connection.
4. Place the speaker over the completed wire
connections.
5. Repeat steps 2 through 5 at each speaker location.
Alternate between using the left channel wires
(white/green) and the right channel wires
(red/black). See the AMPLIFIER CONNECTIONS
SECTION for more detailed wiring diagrams.
1-L 1-R 2-L
IN
OUTINOUT
- -
To Next Speaker
Figure 9: 2-Conductor Trunk
SONANCE DSP2-750
S/N
CAUTION
MADE IN CHINA
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS
RISQUE DE CHOC ELECTRIQUE
2-R
NE PAS OUVRIR
275 watts
IR
IR
CONTROL
STATUS
T15AL / 250VAC
CAUTION
IN
REPLACE FUSE ONLY
WITH
SAME TYPE AND RATING
AC 100-120V ~ 60Hz
ATTENTION
REMPLACER UNIQUEMENT AVEC
VOLTAGE TRIGGER
AC 220-240V ~ 50Hz
LE MEME TYPE ET CALIBRE DU
1- RIGHT
1- LEFT
FUSIBLE
IN OUT
OUT
TCP/IP
3-30 VOLTS
BRIDGE
DHCP ON - DEFAULT
AC or DC
Ω
8
MIN
CLASS 2 WIRING
White
Green
+ +
- -
To Next Left Speaker
Red
Black
+ +
- -
To Next Right Speaker
Figure 10: 4-Conductor Trunk
AMPLIFIER CONNECTIONS
Once all speaker connections have been completed,
connect the 2-conductor or 4-conductor wire to your
amplifier. Take care to ensure that no excess copper
strands are exposed to prevent shorting or other
dangerous electrical hazards.
Connect an audio source to the amplifier. Power on the
amplifier and test the speakers.
5
12” (305mm)
4.86” (123mm)
14.5” (368mm)
8.67” (220mm)
11.36” (289mm)
Bury 6–8” (150–200mm)
SPECIFICATIONS
Frequency Range (-10dB) 35Hz – 25kHz
Frequency Range (-3dB) 60Hz – 20kHz
Power Capacity 120 Watts Continuous Program Power | 60 Watts Continuous Pink Noise
Nominal Sensitivity 88 dB
Nominal Coverage Angle 360 Degrees Hortizontal Coverage, 160 Degrees Vertical Coverage
Rated Maximum SPL 107dB @ 1 Meter (3.3 feet) Average, 133dB Peak
Rated Impedance 8 Ohms Nominal, 6 Ohms Minimum
Transformer Taps 80W, 40W, 20W and (10W @70V)
Crossover Point 500Hz
LF Driver 6.5” (165mm) Polypropylene Cone, Santoprene Rubber Surround
Wide Band Driver Four 1.25” (32mm) EPDM Dome
Input Connectors Flying Leads
Environmental Conforms to Mil Spec 810 for Humidity, IEC 529, IP-66
Included Accessories Silicon Filled Wire Nuts
Dimension HxDia 14.5” x 12” (368mm x 305mm)
Weight 14.6 lbs (6.62kg)
Color Landscape Brown
6
OMNI-6T ARCHITECTURAL
SPECIFICATIONS
70V/100V/8 Ohm Selectable 6.5” Omni-Directional
Outdoor Loudspeaker
The loudspeaker shall deliver 360 degrees horizontal,
160 degrees vertical coverage and consist of a 6.5”
(165mm) Polypropylene cone, Santoprene rubber
surround Woofer and 4 x 1.25” (32mm) EPDM dome,
Wide Band Drivers, with a crossover point of 500Hz.
Frequency range shall be 60Hz – 20kHz (-3dB). Total
power handling shall be 120 Watts continuous program
power, 60 Watts continuous pink noise. Nominal
sensitivity should be rated at 88dB, and it should have
a rated maximum SPL of 107dB @ 1 meter (3.3 feet)
average, 113dB peak. The unit shall be supplied with
a line-matching transformer suitable for 100 volt or
70 volt with a side-mounted control allowing user
selectable power taps of 80W, 40W, 20W and (10W
@70V) and an 8 Ohm bypass. The loudspeaker should
be finished in a dark brown color and shall conform to
Mil Spec 810 for humidity, salt spray, temperature and
UV, have IEC 529 and an IP-66 waterproof rating. The
loudspeaker shall be the Sonance Omni-6T. No other
system shall be acceptable unless the above combined
performance specifications are equaled or exceeded.
TECHNICAL ASSISTANCE
AND SERVICE
The Technical Assistance Department at Sonance is
available at (949) 492-7777 to answer any questions
concerning the operation and installation of your
speakers between the hours of 7:00 AM and 5:00 PM
Pacific time, Monday through Friday, except holidays.
In the event your unit should need repair or service, you
may return the unit to your authorized dealer or use the
following guidelines:
PLEASE KEEP ORIGINAL PACKAGING WHEN POSSIBLE.
1. Be prepared to state the model number and / or
serial number, date of purchase, and dealer’s name
and address when calling.
2. Contact Sonance directly at (949) 492-7777
or at www.sonance.com. YOU MUST HAVE PRIOR
AUTHORIZATION TO RETURN YOUR UNIT.
3. If you are returning the product directly to Sonance,
call us to obtain a return authorization number
(RMA) before shipping.
4. Ship the product via United Parcel Service, Federal
Express, or other package delivery service. Please do
not use the U.S. Postal Service.
5. Include the return authorization number on the
shipping label. Please do not write the RMA number
directly on the carton.
6. Ship to:
Attn: Quality Assurance Department
RMA# (include RMA number here)
Sonance
11016 Mulberry Ave.
Suite B
Fontana, CA 92337
7
LIMITED FIVE (5) YEAR WARRANTY
Sonance warrants to the first end-user purchaser that this Sonance-brand product (“Product”), when purchased from
an authorized Sonance Dealer/Distributor, will be free from defective workmanship and materials for the period stated
below. Sonance will at its option and expense during the warranty period, either repair the defect or replace the Product
with a new or remanufactured Product or a reasonable equivalent.
EXCLUSIONS
TO THE EXTENT PERMITTED BY LAW, THE WARRANTY SET FORTH ABOVE IS IN LIEU OF, AND EXCLUSIVE OF,
ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND IS THE SOLE AND EXCLUSIVE WARRANTY PROVIDED
BY SONANCE. ALL OTHER EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY, IMPLIED WARRANTY OF FITNESS FOR USE, AND IMPLIED WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE ARE SPECIFICALLY EXCLUDED.
No one is authorized to make or modify any warranties on behalf of Sonance. The warranty stated above is the sole and
exclusive remedy and Sonance’s performance shall constitute full and final satisfaction of all obligations, liabilities and
claims with respect to the Product.
IN ANY EVENT, SONANCE SHALL NOT BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL, ECONOMIC, PROPERTY,
BODILY INJURY, OR PERSONAL INJURY DAMAGES ARISING FROM THE PRODUCT, ANY BREACH OF THIS WARRANTY
OR OTHERWISE.
This warranty statement gives you specific legal rights, and you may have other rights which vary from state to state.
Some states do not allow the exclusion of implied warranties or limitations of remedies, so the above exclusions and
limitations may not apply. If your state does not allow disclaimer of implied warranties, the duration of such implied
warranties is limited to period of Sonance’s express warranty. Your Product Model and Description: OMNI-6T. Warranty
Period for this Product: Five (5) years from the date on the original sales receipt or invoice or other satisfactory proof
of purchase. Additional Limitations and Exclusions from Warranty Coverage: The warranty described above is nontransferable, applies only to the initial installation of the Product, does not include installation of any repaired or replaced
Product, does not include damage to allied or associated equipment which may result for any reason from use with
this Product, and does not include labor or parts caused by accident, disaster, negligence, improper installation, misuse
(e.g. overdriving the amplifier or speaker, excessive heat, cold or humidity), or from service or repair which has not been
authorized by Sonance. Obtaining Authorized Service: To qualify for the warranty, you must contact your authorized
Sonance Dealer/Installer or call Sonance Customer Service at (949) 492-7777 within the warranty period, must obtain
a return merchandise number (RMA), and must deliver the Product to Sonance shipping prepaid during the warranty
period, together with the original sales receipt, or invoice or other satisfactory proof of purchase.
©2020 Sonance. All rights reserved. Sonance is a registered trademarks of Dana Innovations. Due to continuous product improvement,
all features and specifications are subject to change without notice. For the latest Sonance product specification information visit our
website: www.sonance.com
SONANCE • 991 Calle Amanecer • San Clemente, CA 92673 USA
PHONE: (949) 492-7777 • FAX: (949) 361-5151 • Technical Support: (949) 492-7777 • www.sonance.com
03.11.2020
8
Loading...