SOMFY tilt wirefree ir Installation Manual
www.somfy.com
5 - 7 m
9 Cm / 3.54 In
9 Cm / 3.54 In
Mark and CutMark and Cut
Installation guide
Tilt WireFree IR
Ref. 5055108A
• This Somfy product must be installed by a professional motorisation and home automation
installer
, for whom these instructions are intended.
• Before installation, check that this product is compatible with the associated equipment and accessories.
• These instructions describe how to install, commission and use this product.
• Moreover, the installer must comply with current standards and legislation in the country
in which the product is being installed, and inform his customers of the operating and maintenance conditions for the product.
• Any use outside the sphere of application specified by Somfy is not approved. Such use,or any failure to
comply with the instructions given herein will invalidate the warranty, And Somfy refuses to accept liability.
TM
Argentina: Somfy Argentina
+54 (0) 1147 373 700
Australia: Somfy PTY
+61 (0) 2 9638 0744
Austria: Somfy GesmbH
+43 (0) 662 62 53 08
Belgium: Somfy Belux
+32 (0) 2 712 07 70
Brasil: Somfy Brasil STDA
+55 1
1 (0) 6161 6613
Canada: Somfy ULC
+1 (0) 905 564 6446
China: Somfy China Co. Ltd
+86 21 (0) 6280 9660
Cyprus : Somfy Middle East
+357 (0) 25 34 55 40
Czech Republic:Somfy Spol s.r.o.
+420 (0) 296 372 486-7
Denmark: Somfy AB
+45 (0) 65325793
Finland: Somfy AB
+358 (0) 957 13 02 30
France : Somfy France
+33 (0) 820 374 374
Germany: Somfy GmbH
+49 (0) 7472 930 0
Greece: Somfy Hellas
+30 (0) 210 614 67 68
Hong Kong: Somfy Co. Ltd
+852 (0) 2523 6339
Hungary : Somfy Kft
+36 (0) 1814 5120
LTD
Denmark
Finland
India: Somfy India PVT
+91 (0) 11 51 65 91 76
Israel: Sisa Home
+972 (0) 3 952 55 54
Indonesia: Somfy Indonesia
+62 (0) 21 719 3620
Italy: Somfy Italia s.r
+39 (0) 024 84 71 84
Japan: Somfy KK
+81-45-475-0732
Kingdom of Saudi Arabia:
Somfy Saudi
+966 (0) 1 46 02 748
Kuwait: Somfy Kuwait
+965 (0) 434 89 01
Lebanon:
cf. Cyprus Somfy Middle East
+961 (0) 1 391 224
Malaisia: Somfy Malaisia
+60 (0)3 228 74743
Mexico:
Somfy Mexico SA
+52 (0) 55 5576 3421
Morocco: Somfy Maroc
+212 (0) 22 95 1
Netherlands: Somfy BV
+31 (0) 23 55 44 900
Norway: Somfy Norway
+47 (0) 67 97 85 05
Poland: Somfy SP
+48 (0) 22 50 95 300
Portugal:cf.Spain Somfy Espana SA
+351 (0) 229 396 840
Ltd
Automation Ltd
.l
de CV
1 53
Z.O.O
Romania: Somfy SRL
+40 (0) 368 444 081
Russia: Somfy LLC
+7 (0) 495 360 47 72
Singapore: Somfy PTE L
+65 (0) 638 33 855
Slovaquia: cf. Czech Republic
Somfy Spol s.r
+420 (0) 296 372 486-7
South Korea: Somfy JOO
+82 (0) 2 594 4333
Spain: Somfy Espana SA
+34 (0) 934 800 900
Sweden: Somfy AB
+46 (0) 40 165900
Switzerland: Somfy A.G.
+41 (0) 44 838 40 30
Taïwan: Somfy T
+886 (0) 2 8509 8934
Thailand:Somfy Bangkok
Regional Of
+66 (0) 2714 3170
Turkey: Somfy T
+90 (0) 216 651 30 15
UAE: Somfy Gulf
+971 (0)4 88 32 808
United Kingdom: Somfy L
+44 (0) 113 391 3030
United States:
Somfy Systems Inc
+1 (0) 609 395 1300
fice
TD
.o.
aiwan
urkey
TD
12 V
8 X AA/LR6
Lithium Battery
INSTALLATION
[1]. SHAFT
a. Slide shaft to the far side of the headrail until is
9cm / 3.54Inches from the end.it
b. If shaft does not slide 9cm / 3.54Inches from
the end, mark and cut shaft to remove 9cm /
3.54Inches from the end of the headrail (use
motor to measure mark).
c. If needed, file the end of the shaft to remove
any rough edges.
[2]. MOT
ADAPTATION
OR MOUNTING
a. Position the blinds to be open fully (horizontal)
b. Put the motor into the appropriate headrail
adaptor and secure snaps on top of motor.
c. If needed, press the shaft adaptor into the
motor
.
[3]. MOTOR INTEGRATION INSIDE HEADRAIL
Slide the motor into the headrail until the shaft is
fully inserted into the motor.
[4]. POWER SUPPL
CONNECTION
Y & IR SENSOR
a. On the back of the motor, there are
two connectors.
One is for the power supply (1) and the other for
the IR sensor (2).
b. Connect the battery to the motor.
c. Connect the IR sensor to the motor using the
lower terminals of the motor IR data connector.
[1]
ab
[2]
[3]
[4]
(1)
(2)
USER MODE
[1]. USER
a. To move the shade from one closed position to
the other closed position, briefly press the UP or
DOWN button.
b. To stop the motor, press the MIDDLE button.
c. To tilt the slats,press and hold the Up or
DOWN button on the transmitter.
MODE
[1]
[2]. LIGHT GAP ADJUSTMENT
12
34
56
7
8
PROG.
1- 8 1- 4 5 - 8
12
3
4
5
6
78
PROG.
1- 8 1- 4 5 - 8
12
34
56
78
PROG.
1- 8 1- 4 5 - 8
1
2
3
4
56
78
P
ROG.
1- 8 1- 4 5 - 8
X 3
12
34
5
6
78
PROG.
1- 8 1- 4 5 - 8
1
2
34
56
7
8
PROG.
1- 8 1- 4 5 - 8
1
2
3
4
56
78
P
ROG.
1- 8 1- 4 5 - 8
12
34
56
78
P
ROG.
1- 8 1- 4 5 - 8
12
34
56
78
PROG.
1- 8 1- 4 5 - 8
12
34
56
78
PROG.
1
-8 1- 4 5 - 8
12
34
56
78
1- 8 1- 4 5 - 8
12
34
56
78
1
-8 1- 4 5 - 8
a. Press the UP and DOWN buttons simultaneously until the motor jogs.
b. Press the UP and STOP or DOWN and STOP buttons until the motor
jogs to adjust the gap.
c. To test the new light gap, move the shade to close position with the
UP or DOWN button.
c. To confirm the new settings, press the STOP button until the motor
jogs.
Note: After the 3rd consecutive adjustement without testing,the amount
of change factor will increase 10x.
[2]
[3]. MOT
OR DIRECTION CHANGE
a. Press the UP and DOWN buttons simultaneously until the motor jogs.
b. Press the UP, STOP and DOWN buttons, to change the direction.
The motor jogs.
[4]. ASSIGN
A CHANNEL
Only with the IR8 transmitter.
Note: By factory default, the motor is paired to ALL the channels on the
transmitter. To designate one channel to a particular shade, the user
must first delete unwanted channels (see step [5] DELETE A
CHANNEL).
To enter in programming mode: Press on the transmitter prog button until
the motor jogs.
To program one channel: press on key 1 and next on the key of the
channel to program (1 to 8) or channel group until the motor jogs.
To exit programming mode: press on the transmitter prog button until the
motor jogs.
[5].DELETE A CHANNEL
Only with the IR8 transmitter.
[3]
[4]
[5]
To enter in programming mode: Press on the transmitter prog button until
the motor jogs.
To erase one channel: press on key 8 and next on the key of the
channel to program (1 to 8) or channel group until the motor jogs.
To erase all channels: press on key 8 and next on key 1->8 until the
motor feedback.
To exit programming mode: press on the transmitter prog button until the
motor jogs.
[6].CHANNEL
SELECTION
Press 1 to 8 button.The motor jogs once the channel is paired.
[7]. F
ACTORY RESET
a. Position the blinds to be open fully (horizontal)
b. With the motor prog button: Press on the motor prog button until the
motor jogs 3 times. The first at 2s, the second at 7s and the third at 12s.
TROUBLE SHOOTING
The motor does not work
Verify:
• The batteries of the motor or of
the remote control
• The compatibility of the remote
control
The equipment stops too soon
Verify:
• The batteries of the motor
• The light gap of the motor is
properly adjusted
[6]
[7]
SOMFY hereby declares that this product complies with the essential requirements and other relevant provisions of
Directive 1999/5/EC. A Declaration of Conformity is available at the web address www.somfy.com/CE. Suitable for use in
EU, CH and NO
Copyright © 2008 Somfy SAS. All rights reserved.
Somfy SAS, capital 20.000.000 Euros, RCS Bonneville 303.970.230 04/2008
Loading...