SOMFY Tilt 50 RTS Instructions Manual

Tilt 50 RTS

Ref. 5122959A

Instructions

Notice

Manual

CONTENTS

1. PREREQUISITE INFORMATION

1.1 FIELDS OF APPLICATION

The Tilt 50 RTS is a motor specially dedicated to interior applications. The Tilt 50 RTS can motorize wood venetian blinds. The Tilt 50 RTS is a battery operated motor, powered with lithium primary batteries or NiMH batteries mounted with or without a solar pack. The motor can also be powered by a power supply.

Use only the below Somfy references with this motor : Ref. 9018685 : 12V RELOADABLE TUBE (8 AA LITHIUM) + Ref. 9014834 : 8 AA LITHIUM BATTERY PACK Ref. 9018608 : 12V RELOADABLE TUBE (10 AA NIMH) + Ref. 9018621 : 10AA NIMH BATTERIES Ref. 9019034 : SOLAR PACK Ref. 1822445 : 12V AC/DC Power Supply Caution : Batteries must be installed as shown on the battery tube. Do not mix type, brand or used batteries with new.

Warning : The Tilt 50 RTS is compatible only with the «Sunis Indoor WireFreeTM RTS» sensor. Warning : The Tilt 50 RTS cannot be used with sealed double glazing.

Please separate storage cells and batteries from other types of waste and recycle them via your local collection facility.

1. Prerequisite information 3

1.1. Fields of application 3

1.2. Liability 4

2. Installation 4

2.1. Installation 5

2.2. wiring 6

2.3. commissioning 6

2.4. Tips and recommendations for installation 8

3. Use and maintenance 9

3.1. Up and Down buttons 10

3.2. STOP function 10

3.3. Favourite position (my) 10

3.4. Tilting 10

3.5. Additional setting 10

3.6.

Tips and recommendations for use

4. Technical data 12

1.2 LIABILITY

Before installing and using the motor, please read operating and installation guide carefully. In addition to following the instructions given in this guide, the instructions detailed in the attached Safety instructions document must also be observed.

The motor must be installed by a motor and home automation professional, according to instructions from Somfy and the regulations applicable in the country in which it is commissioned.

It is prohibited to use the motor outside the elds of application described above.

Such use, and any failure to comply with the instructions given in this guide and in the attached Safety instructions document, absolves Somfy of any liability and invalidates the warranty.

The installer must inform its customers of the operating and maintenance conditions for the motor and must provide them with the instructions for use and maintenance, and the attached Safety instructions document, after installing the motor. Any After-Sales Service operation on the motor must be performed by a motor and home automation professional.

If in doubt when installing the motor, or to obtain additional information, contact a Somfy adviser or go to the website www.somfy.com

Safety warning!

Information



Caution!

2. INSTALLATION

Instructions which must be followed by the motor and home automation professional installing the Tilt 50 RTS motor.

Never drop, knock, drill or submerge the motor.

Install a separate control point for each motor.

 



2.1. INSTALLATION

2.1.1. Shaft adaptation

1) Slide shaft to far side of the headrail until is 9cm / 3.54In from the end.

2) If shaft does not slide 9cm / 3.54In from the end, mark and cut shaft to remove 9cm / 3.54In from the end of the headrail (use motor to measure mark). If needed, file the end of the shaft to remove any rough edges.

2.1.2. Motor preparation

1) Put the motor into the appropriate headrail adaptor and secure snaps on top of motor.

2) If needed, press the shaft adaptor into the motor.

2.1.3. Motor/headrail assembly

Position the blind to be fully open (horizontal). Slide the motor into the headrail until the shaft is fully inserted into the motor.

9 Cm / 3.54 In



2.2 WIRING

Cables which pass through a metal wall must be protected and isolated using a sheath or sleeve.

Attach cables to prevent any contact with moving parts.

The cable for the Tilt 50 RTS cannot be removed. If it is damaged, return the motor to the After-Sales department.

Leave the motor power supply cable accessible: it must be possible to replace it easily.

Do not unplug the battery when the motor is working.

Plug the battery with the motor supply cable :

2.3. COMMISSIONING

2.3.1. Programming the RTS control point

Press the Up and Down buttons simultaneously on the RTS control point: the motorised product moves up and down and the control point is preprogrammed in the motor

2.3.2. Checking the direction of rotation

1) Press the Up button on the RTS control point:

a) If the motorised product rises (a), the direction of rotation is correct: Move onto the section 2.3.3 entitled “Setting the end limits”.

b) If the motorised product lowers (b), the direction of rotation is incorrect: Move onto the next step (2).

2) Press the my button on the RTS control point until the motorised product moves up and down: The direction of rotation has been

modied.

3) Press the Up button on the RTS control point to check the direction of rotation.



2) 3)

2.3.3. Setting the end limits

The end limits can be set in any order.

1) Raise the motorised product to the desired position by pressing the Up button.

2) Press the my and Down buttons at the same time until the motorised product moves.

The upper end limit is memorised.

3) Press the my button when the motorised product reaches the desired lowered position. If necessary, adjust the position of the motorised product using the Up and Down buttons.

4) Press the my and Up buttons at the same time until the motorised product moves.

The lower end limit is memorised. The motorised product rises and stops in the raised position.

5) To conrm the end limits, press the my button until the motorised product moves up and down.

The end limits are programmed.

Do not set an end limit in a position able to raise the motorised product, as this could damage the motorised product and/or the motor in the long term.

2.3.4. Recording the RTS control point

The motorisation is in programming mode:

-- Quickly press the PROG button on the RTS control point to be programmed:

→The motorised product moves up and

down: this RTS control point is programmed in the motorisation.

If the motorisation is no longer in programming mode, repeat Step 2.3.1 then perform Step 2.3.4.

1) 2)

3) 4)

PROG.

2.4. TIPS AND RECOMMENDATIONS FOR INSTALLATION

2.4.1. Questions about the Tilt 50 RTS?

Observations Possible causes Solutions

The motorised product does not operate.

There may be some radio interferences.

Unplug the motor supply cable and reconnect the battery tube to the motor.

One or more batteries have been mounted backwards.

Verify that batteries are all mounted in the correct manner.

Batteries (inside battery tube) are weak.

Check whether the batteries are weak and replace if necessary.

The control point battery is weak.

Check whether the battery is weak and replace it if necessary.

The control point is not compatible.

Check for compatibility and replace the control point if necessary.

The control point used has not been programmed into the motor.

Use a programmed control point or program this control point.

2.4.2. Re-setting the end limits Readjusting the upper end limit

1) Press the Up button to bring the motorised product to the end limit to be readjusted.

2) Press the Up and Down buttons at the same time until the motorised product moves up and down.

3) Press the Up or Down button to move the motorised product to the new desired position.

4) To conrm the new end limit, press the my button until the motorised product moves up and down.

Readjusting the lower end limit

1) Press the Down button to bring the motorised product to the end limit to be readjusted.

2) Press the Up and Down buttons at the same time until the motorised product moves up and down.

3) Press the Up or Down button to move the motorised product to the new desired position.

4) To conrm the new end limit, press the my button until the motorised product moves up and down.

2.4.3. Adding or deleting a RTS control point

Find an RTS control point (A) programmed in the motor. Press and hold the RTS programmed control point (A) PROG button or the motor PROG button until the motorised product moves up and down: the motor is in programming mode. Quickly press the RTS control point(B) PROG button to add or delete: the motorised product moves up and down and the RTS control point is programmed or deleted from the motor.

2.4.4. Erasing the control point from the memory of the motor

To delete all the programmed control points, press and hold the motor PROG button until the motorised product moves up and down twice. All the control points are deleted.

2.4.5. Erasing the memory of the motor

To reset the motor, press and hold the PROG button on the motor head until the motorised product moves up and down 3 times. All the settings are erased.

3. USE AND MAINTENANCE

This motor is maintenance-free

These instructions only describe the use with a “Telis modulis” control point. For use with an other control point, refer to the corresponding manual.

A B

3.1. UP AND DOWN BUTTONS

Briey press the Up or Down button fully raise or lower the motorised product.

3.2. STOP FUNCTION

The motorised product is moving.

- Briey press the STOP button: the motor-

ised product stops automatically.

3.3. FAVOURITE POSITION (my)

To use the favourite position (my):

- Briey press my: the motorised product

starts to move, and stops in the favourite position (my).

To modify or delete the favourite (my) position, see the section entitled “Additional settings”.

3.4. TILTING

To tilt the slats, use the scroll of the remote control, until the slats reach the desired position.

3.5. ADDITIONAL SETTINGS

3.5.1. Record or Modify the favourite position (my)

1) Place the motorised product in the desired

favourite position (my).

2) Press my until the motorised

product moves up and down: the desired favourite position (my) has been programmed.

3.5.2. Deleting the favourite position (my)

1) Press my: the motorised product starts to move, and stops in the favourite position (my).

2) Press my again until the motorised product moves: the favourite position (my) is deleted.

3.5.3. Adjusting the tilting speed

1) To decrease the tilting speed, press and hold the my and Down buttons simultaneously until the motorised product moves up and down. Repeat as needed. If the motorised product does not moves up and down, then the minimum setting has been reached.

2) To increase the tilting speed, press and hold the my and Up buttons simultaneously until the motorised product moves up and down. Repeat as needed. If the motorised product does not moves up and down, then the maximum setting has been reached.

3.5.4. Modifying the wheel rotation direction

1) Move the motorised product away from the end limits.

2) Press the Up and Down buttons simultaneously, until the motorised product makes an Up and Down movement.

3) Press the Up, my and Down buttons simultaneously, until the motorised product moves up and down, to reverse the wheel rotation direction.

2 3

3.6. TIPS AND RECOMMENDATIONS FOR USE

Questions about the Tilt 50 RTS?

If the motorised product still does not work, contact a motorisation and home automation professional.

4. TECHNICAL DATA

Somfy hereby declares that the product conforms with the essential requirements and other relevant provisions of the European Directives applicable for Europe. A Declaration of Conformity is available at www.somfy.com/ce.

Power supply 12 Vdc SELV

Radio frequency

433.42 MHz

Torque 1 Nm

Up speed 10 rpm

Down speed 10 rpm

Electrical insulation III

Minimum distance between two end-limit 0,25 turn

Maximum distance between two end-limit 5 turns

Maximum running time 1 min

Operating temperature 0°C to + 60°C

Protection rating IP 20 (For indoor use only)

Observations Possible causes Solutions

The motorised product does not operate.

One or more batteries have been mounted backwards.

Verify that batteries are all mounted in the correct manner.

Batteries (inside battery tube) are weak.

Check whether the batteries are weak and replace if necessary.

The control point battery is weak.

Check whether the battery is weak and replace it if necessary.

SOMMAIRE

1. INFORMATIONS PRÉALABLES

1.1 DOMAINE D’APPLICATION

Le Tilt 50 RTS est un moteur spécialement dédié aux applications intérieures. Le Tilt 50 RTS peut motoriser des stores vénitien en bois. Le Tilt 50 RTS est un moteur fonctionnant sur batterie, alimenté par des batteries au lithium ou des batteries NiMH avec ou sans le « Solar pack ». Le moteur peut également être alimenté par un bloc d’alimentation.

Utiliser uniquement les références ci-dessous avec ce moteur: Ref. 9018685 : 12V RELOADABLE TUBE (8 AA LITHIUM) + Ref. 9014834 : 8 AA LITHIUM BATTERY PACK Ref. 9018608 : 12V RELOADABLE TUBE (10 AA NIMH) + Ref. 9018621 : 10AA NIMH BATTERIES Ref. 9019034 : SOLAR PACK Ref. 1822445 : 12V AC/DC Power Supply

Attention : Les batteries doivent être installées comme indiqué sur le tube batterie. Ne pas mélanger le type, la marque ou des bateries usagées avec des neuves.

Attention: Le Tilt 50 RTS est uniquement compatible avec le capteur «Sunis Indoor WireFreeTM RTS ». Attention: Tilt 50 RTS ne peut pas être utilisé avec des double vitrage scellé.

Veiller à séparer les piles et batteries des autres types de déchets et à les recycler via votre systeme local de collecte.

1. Informations préalables 13

1.1. Domaine d’application 13

1.2. Responsabilité 14

2. Installation 14

2.1. Montage 15

2.2. Câblage 16

2.3. Mise en service 16

2.4. Astuces et conseils d’installation 18

3. Utilisation et maintenance 19

3.1. Touches Montée et Descente 20

3.2. Fonction STOP 20

3.3. Position favorite (my) 20

3.4. Orientation 20

3.5. Réglages supplémentaires 20

3.6. Astuces et conseils d’utilisation 22

4. Données techniques 22

1.2 RESPONSABILITÉ

Avant d’installer et d’utiliser la motorisation, lire attentivement cette notice. Outre les instructions décrites dans cette notice, respecter également les consignes détaillées dans le document joint Consignes de sécurité.

La motorisation doit être installée par un professionnel de la motorisation et de l’automatisation de l’habitat, conformément aux instructions de Somfy et à la réglementation applicable dans le pays de mise en service.

Toute utilisation de la motorisation hors du domaine d’application décrit ci-dessus est

interdite. Elle exclurait, comme tout irrespect des instructions gurant dans cette notice

et dans le document joint Consignes de sécurité, toute responsabilité et garantie de Somfy.

L’installateur doit informer ses clients des conditions d’utilisation et de maintenance de la motorisation et doit leur transmettre les instructions d’utilisation et de maintenance, ainsi que le document joint Consignes de sécurité, après l’installation de la motorisation. Toute opération de Service Après-Vente sur la motorisation nécessite l’intervention d’un professionnel de la motorisation et de l’automatisation de l’habitat.

Si un doute apparaît lors de l’installation de la motorisation ou pour obtenir des informations complémentaires, consulter un interlocuteur Somfy ou aller sur le site www.somfy. com.

Avertissement

Sécurité!

Information



Attention!

2. INSTALLATION

Consignes à suivre impérativement par le professionnel de la motorisation et de l’automatisation de l’habitat réalisant l’installation de la motorisation Tilt 50 RTS.

Ne jamais laisser tomber, choquer, percer, immerger la motorisation.

Installer un point de commande individuel pour chaque motorisation.

 



+ 30 hidden pages

SOMFY Tilt 50 RTS Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual