SOMFY SUNEA CMO User Manual
SUNEA RTS CMO VISUAL REFERENCE GUIDE
STANDARD AWNING SETTINGS:
Both UP and DOWN limits need to be set.
!
Before You Begin:
Make sure the DOWN button on the remote extends the awning. ( = awning moves outward or extends). Failure to correct this
may cause damage to the awning or personal injury.
Initiate programming by
STEP 1
pressing both the (Up) and
(Down) buttons at the same
my
time until the motor jogs.
STEP 4
my
my
Press the button
until the motor begins
and
to move up. the motor will
stop at the original upper
point.
ADJUSTING THE LIMITS
To change the lower limit:
Move the motor to its current lower limit position and let it stop. Press and hold the and buttons simultaneously until the motor
jogs, then release. Adjust to a new lower limit position. Press the button until the motor jogs, then release. Check new limit.
my
To change the upper limit:
Move the motor to its current upper limit position and let it stop. Press and hold the and buttons simultaneously until the motor
jogs, then release. Adjust to a new upper limit position. Press the button until the motor jogs, then release. Check new limit.
Check the direction of operation.
Press and hold the button and
my
confirm it moves the motor out.
To change the direction press and
hold the (Stop) button until the
my
my
motor jogs.
Bring the motor to your desired
upper limit by pressing the
button. Press and hold both
the and buttons until
the motor begins to move
down, then release. Use the
my
button to stop it at the desired
STEP 2
STEP 3
my
lower limit
my
Press and hold the button
until the motor jogs
STEP 5
my
op
Press and hold the Program
button on the back of the
STEP 6
transmitter until the motor
jogs. Double check limits as
a precaution.
my
my
To add a remote/channel or sun and wind sensor:
First press the programming button on the back of the already programmed remote until the motor jogs. Then press the programming
button on the remote or sun/wind sensor that you would like to add until the motor jogs. Check it.
To reset the motor:
you will need to disconnect power (120vac) for 2 seconds, reconnect for 10 seconds, disconnect for another 2 seconds and reconnect.
The motor should start to move or jog (If this does not happen, continue to perform the disconnects until it does). Once the motor stops,
press and hold the programming button on the back of the remote and count to ten without letting go. The motor should jog twice.
ADVANCED FEATURE FUNCTIONS
BACK IMPULSE function for both cassette and standard awnings
This function allows you to apply tension on the fabric when the awning is fully extended. The motor can be adjusted up to a ½ half turn.
STEP 1
Disconnect power
momentarily and
reconnect.
STEP 2
Set the awning
to the lowest
position.
my
SOMFY CANADA
1-800-22SOMFY 1-905-564-6446
© SOMFY SYSTEMS, INC. 4/2015
STEP 3
Press the MY and Up
buttons until the awning
jogs: The motor is in
programming mode.
WWW.SOMFYSYSTEMS.COM
L-0138
my
STEP 4
Adjust the fabric's
tension using the Up
or Down buttons.
my
STEP 5
Press the MY button until
the awning jogs: The
fabric's tension has been
programmed.
my
CASSETTE AWNING SETTINGS:
Only DOWN limit needs to be set. UP limit is set automatically.
!
Before You Begin:
Make sure the DOWN button on the remote extends the awning. ( = awning moves outward or extends). Failure to correct this
may cause damage to the awning or personal injury.
Initiate programming by
STEP 1
my
pressing both the (Up) and
(Down) buttons at the same
time until the motor jogs.
STEP 4
Stop the awning halfway in
by pressing the button.
my
ADJUSTING THE LIMITS
To change the lower limit:
my
Move the motor to its current lower limit position and let it stop. Press and hold the and buttons simultaneously until the motor
jogs, then release. Adjust to a new lower limit position. Press the button until the motor jogs, then release. Check new limit.
To add a remote/channel or sun and wind sensor:
First press the programming button on the back of the already programmed remote until the motor jogs. Then press the programming
button on the remote or sun/wind sensor that you would like to add until the motor jogs. Check it.
To reset the motor:
you will need to disconnect power (120vac) for 2 seconds, reconnect for 10 seconds, disconnect for another 2 seconds and reconnect.
The motor should start to move or jog (If this does not happen, continue to perform the disconnects until it does). Once the motor stops,
press and hold the programming button on the back of the remote and count to ten without letting go. The motor should jog twice.
Check the direction of operation.
my
Press and hold the button and
confirm it moves the awning out.
To change the direction press and
hold the (Stop) button until the
my
my
motor jogs.
mymy
Press and hold the button
STEP 5
my
op
until the motor moves. It will
automatically set the upper
limit.
Bring the motor to your desired
lower limit by pressing the
button. Press and hold both
the and buttons until
the motor begins to move up,
Press and hold the Program
button on the back of the
transmitter until the motor
jogs. Double check limits as
STEP 2
STEP 3
my
then release.
STEP 6
a precaution.
my
ADVANCED FEATURE FUNCTIONS
BACK IMPULSE function for both cassette and standard awnings
This function allows you to apply tension on the fabric when the awning is fully extended. The motor can be adjusted up to a ½ half turn.
STEP 1
Disconnect power
momentarily and
reconnect
STEP 2
Set the awning
to the lowest
position.
my
STEP 3
Press the MY and Up buttons
until the awning jogs: The
motor is in programming mode.
my
BACK RELEASE function on cassette awnings only
This function allows the fabric tension to be decreased after the cassette awning is closed.
STEP 1
Disconnect power
momentarily and
reconnect
STEP 2
Set the awning
to the inner
limit position.
my
STEP 3
Press the MY and Down buttons until the motor moves up and
down: If the Back release function was deactivated, it is activated.
If the Back release function was active, it is deactivated.
CLOSING FORCE function on cassette awnings only
This function enables the closing force of the awning to be increased or decreased to 3 levels (high/medium/low).
The motor is factory set at the medium level.
STEP 1
Disconnect power
momentarily and reconnect
STEP 4
Adjust the closing force setting using the Up and Down buttons.
- to increase the closing force, press the Up button until the motor jogs up and down.
- to decrease the closing force, press the Down button until the motor jogs up
and down. (delayed jog for levels 3 and 1) (short jog for level 2)
STEP 2
Bring the awning to
the halfway position.
cassette
STEP 3
Briefly press the MY and Up buttons simultaneously, then immediately
press and hold the MY and Up buttons until the motor jogs. The motor
is only inprogramming mode for approx. 10 seconds.
STEP 4
Adjust the fabric's
tension using the
Up or Down buttons.
Increases
closing force
my
my
Decreases
closing force
STEP 5
Press the MY button
my
until the awning jogs:
The fabric's tension has
been programmed.
STEP 5
Press the MY button until
the awning jogs up and
down: The new closing force
has been programmed.
my
my
+
my
my
my
Loading...